[alsa-devel] [Patch V5 00/12] ASoC: QCOM: Add support for ipq806x SOC
From: Kenneth Westfield kwestfie@codeaurora.org
This patch series adds support for I2S audio playback on the Qualcomm Technologies ipq806x SOC.
The ipq806x SOC has audio-related hardware blocks in its low-power audio subsystem (or LPASS). One of the relevant blocks in the LPASS is its low-power audio interface (or LPAIF). This contains an MI2S port, which is what these drivers are configured to use. The LPAIF also contains a DMA engine that is dedicated to moving audio samples into the transmit FIFO of the MI2S port.
The development board being used for testing contains the ipq806x SOC and a Maxim max98357a DAC/amp. One bus from the MI2S port of the SOC is connected to the DAC/amp for stereo playback. This bus is configured so that the SOC is bus master and consists of DATA, LRCLK, and BCLK. The DAC/amp does not need MCLK to operate. In addition, a single GPIO pin from the SOC is connected to the same DAC/amp, which gives enable/disable control over the DAC/amp.
The specific drivers added are: * a codec DAI driver for controlling the DAC/amp * a CPU DAI driver for controlling the MI2S port * a platform driver for controlling the LPAIF DMA engine * a machine driver that instantiates a dai-link for playback
Corresponding additions to the device tree for the ipq806x SOC and its documentation has also been added. Also, as this is a new directory, the MAINTAINERS file has been updated as well.
The LPASS also contains clocks that need to be controlled. Those drivers have been submitted as a separate patch series: [PATCH v3 0/8] qcom audio clock control drivers http://lkml.org/lkml/2015/1/19/656
= Changes since V4 [Patch V4 00/10] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2015-February/087499.ht...
* Replaced simple-card with a machine driver to resolve the system clock configuration, rather than having the CPU DAI driver do it. * Added header files to avoid indirect header dependencies and implicit forward declarations. * Tweaked the ISR to match the conventions of the surrounding code. * Removed the usage of the low-power memory as it is not needed. * Removed the use of the DRV_NAME constant. * Added explicit dependancy on gpiolib for the codec driver. * Moved the MODULE_DEVICE_TABLE macro inside the CONFIG_OF conditional. * Modified the documentation to reflect the changes. * General code cleanup.
= Changes since V3 [Patch V3 00/10] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2014-December/085694.ht...
* Placed the content of the inline functions into the callbacks. * Replaced use of readl/writel register access functions with regmap access functions. Notable exception is the ISR, which uses ioread32/iowrite32. * Rearranged the sequencing of the hardware block enables to fit within the ASoC framework callbacks, while remaining functional. REQ 1: The hardware requires the enable sequence to be: LPAIF-DMA[enable],then LPAIF-MI2S[enable], then DAC-GPIO[enable] REQ 2: The hardware requires the disable sequence to be: DAC-GPIO[disable], then LPAIF-MI2S[disable] * Corrected the implementation of the pointer callback. * Utilize the LPM to buffer audio samples, rather than memory external to LPASS. * Corrected the interrupt clearing in the ISR. * Implemented a default system clock (defined by the simple-card DT node), and optional LPASS DT node modifiers that can alter the system clock in order to expand the range of available bit clock frequencies. * Addressed all of the remaining issues raised by Mark Brown. * General code cleanup.
= Changes since V2 [Patch v2 00/11] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2014-December/085186.ht...
* Removed the PCM platform driver from the DTS platform and tied it to the CPU DAI driver. * Changed I2S pinctrl to use generic naming convention and moved control to CPU DAI driver. It should be controlled now by soc-core's pinctrl_pm_* functionality. * Added stub DAPM support in codec driver. As the DAC GPIO needs to be enabled last when starting playback, and disabled first when stopping playback, it seems as though the trigger function may be the place for this. Suggestions are welcome for a better place to put this. * Removed machine driver and tied DAI drivers to simple-audio-card. * Packaged the build files and Maxim codec files together in one change. * Removed QCOM as vendor from Maxim code and documentation. * Separated the SOC and board definitions into the correct DTS files. * Update device tree documentation to reflect changes. * General code cleanup.
= Changes since V1 [PATCH 0/9] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2014-November/084322.ht...
* Remove the native LPAIF driver, and move its functionality to the CPU DAI driver. * Add a codec driver to manage the pins going to the external DAC (previously managed by the machine driver). * Use devm_* and dev_* where possible. * ISR only handles relevant DMA channel now. * Update device tree documentation to reflect changes. * General code cleanup.
Kenneth Westfield (12): MAINTAINERS: Add QCOM audio ASoC maintainer ASoC: max98357a: Document MAX98357A bindings ASoC: qcom: Document LPASS CPU bindings ASoC: qcom: Document IPQ806X-MAX89357A bindings ASoC: codec: Add MAX98357A codec driver ASoC: ipq806x: add LPASS header files ASoC: ipq806x: Add LPASS CPU DAI driver ASoC: ipq806x: Add LPASS platform driver ASoC: ipq806x: Add @max98357a machine driver ASoC: qcom: Add ability to build QCOM drivers ASoC: Allow for building QCOM drivers ARM: dts: Model IPQ LPASS audio hardware
.../devicetree/bindings/sound/max98357a.txt | 14 + .../bindings/sound/qcom,ipq806x-max98357a.txt | 24 + .../devicetree/bindings/sound/qcom,lpass-cpu.txt | 38 ++ MAINTAINERS | 7 + arch/arm/boot/dts/qcom-ipq8064.dtsi | 23 + sound/soc/Kconfig | 1 + sound/soc/Makefile | 1 + sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max98357a.c | 145 ++++++ sound/soc/qcom/Kconfig | 26 + sound/soc/qcom/Makefile | 11 + sound/soc/qcom/ipq806x-max98357a.c | 171 +++++++ sound/soc/qcom/lpass-cpu.c | 481 +++++++++++++++++++ sound/soc/qcom/lpass-lpaif-ipq806x.h | 172 +++++++ sound/soc/qcom/lpass-platform.c | 526 +++++++++++++++++++++ sound/soc/qcom/lpass.h | 51 ++ 17 files changed, 1697 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/max98357a.txt create mode 100644 Documentation/devicetree/bindings/sound/qcom,ipq806x-max98357a.txt create mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt create mode 100644 sound/soc/codecs/max98357a.c create mode 100644 sound/soc/qcom/Kconfig create mode 100644 sound/soc/qcom/Makefile create mode 100644 sound/soc/qcom/ipq806x-max98357a.c create mode 100644 sound/soc/qcom/lpass-cpu.c create mode 100644 sound/soc/qcom/lpass-lpaif-ipq806x.h create mode 100644 sound/soc/qcom/lpass-platform.c create mode 100644 sound/soc/qcom/lpass.h
From: Kenneth Westfield kwestfie@codeaurora.org
Add maintainers for the Qualcomm Technologies sound drivers.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS index d66a97dd3a12548e0f79c59154260724da11f282..9beda051e158156e2f7742485059ca299ed6a3d5 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -5183,6 +5183,13 @@ F: drivers/char/ipmi/ F: include/linux/ipmi* F: include/uapi/linux/ipmi*
+QCOM AUDIO (ASoC) DRIVERS +M: Patrick Lai plai@codeaurora.org +M: Banajit Goswami bgoswami@codeaurora.org +L: alsa-devel@alsa-project.org (moderated for non-subscribers) +S: Supported +F: sound/soc/qcom/ + IPS SCSI RAID DRIVER M: Adaptec OEM Raid Solutions aacraid@adaptec.com L: linux-scsi@vger.kernel.org
From: Kenneth Westfield kwestfie@codeaurora.org
Add documentation to the sound directory of the device-tree bindings for the Maxim MAX98357A audio DAC.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- Documentation/devicetree/bindings/sound/max98357a.txt | 14 ++++++++++++++ 1 file changed, 14 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/max98357a.txt
diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt new file mode 100644 index 0000000000000000000000000000000000000000..a7a149a236e55b8372b7cb3622cd6a6c664d4e2d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -0,0 +1,14 @@ +Maxim MAX98357A audio DAC + +This node models the Maxim MAX98357A DAC. + +Required properties: +- compatible : "maxim,max98357a" +- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin + +Example: + +max98357a { + compatible = "maxim,max98357a"; + sdmode-gpios = <&qcom_pinmux 25 0>; +};
On Wed, Feb 11, 2015 at 06:10:05PM -0800, Kenneth Westfield wrote:
From: Kenneth Westfield kwestfie@codeaurora.org
Add documentation to the sound directory of the device-tree bindings for the Maxim MAX98357A audio DAC.
This driver has already been applied. If there are any changes to current code please send incremental patches.
On Thu, Feb 12, 2015 at 11:29:18AM +0800, Mark Brown wrote:
On Wed, Feb 11, 2015 at 06:10:05PM -0800, Kenneth Westfield wrote:
From: Kenneth Westfield kwestfie@codeaurora.org
Add documentation to the sound directory of the device-tree bindings for the Maxim MAX98357A audio DAC.
This driver has already been applied. If there are any changes to current code please send incremental patches.
No changes from V4 to V5. Please drop this patch.
From: Kenneth Westfield kwestfie@codeaurora.org
Add documentation to the sound directory of the device-tree bindings for the IPQ806x LPASS CPU DAI device.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- .../devicetree/bindings/sound/qcom,lpass-cpu.txt | 38 ++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt
diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt new file mode 100644 index 0000000000000000000000000000000000000000..621773d1c64af8f4f9eaceb2f7d2d7ec17c66aeb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt @@ -0,0 +1,38 @@ +* Qualcomm Technologies LPASS CPU DAI + +This node models the Qualcomm Technologies Low-Power Audio SubSystem. + +Required properties: + +- compatible : "qcom,lpass-cpu" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : A list which must include the following entries: + * "ahbix-clk" + * "mi2s-osr-clk" + * "mi2s-bit-clk" +- interrupts : Must contain an entry for each entry in + interrupt-names. +- interrupt-names : A list which must include the following entries: + * "lpass-irq-lpaif" +- pinctrl-N : One property must exist for each entry in + pinctrl-names. See ../pinctrl/pinctrl-bindings.txt + for details of the property values. +- pinctrl-names : Must contain a "default" entry. +- reg : Must contain an address for each entry in reg-names. +- reg-names : A list which must include the following entries: + * "lpass-lpaif" + +Example: + +lpass@28100000 { + compatible = "qcom,lpass-cpu"; + clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; + interrupts = <0 85 1>; + interrupt-names = "lpass-irq-lpaif"; + pinctrl-names = "default", "idle"; + pinctrl-0 = <&mi2s_default>; + pinctrl-1 = <&mi2s_idle>; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; +};
From: Kenneth Westfield kwestfie@codeaurora.org
Add documentation to the sound directory of the device-tree bindings for the IPQ806x-MAX98357A soundcard.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- .../bindings/sound/qcom,ipq806x-max98357a.txt | 24 ++++++++++++++++++++++ 1 file changed, 24 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/qcom,ipq806x-max98357a.txt
diff --git a/Documentation/devicetree/bindings/sound/qcom,ipq806x-max98357a.txt b/Documentation/devicetree/bindings/sound/qcom,ipq806x-max98357a.txt new file mode 100644 index 0000000000000000000000000000000000000000..54c6211ce34ab8eb5c764df516c875694eeab3cb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,ipq806x-max98357a.txt @@ -0,0 +1,24 @@ +* Qualcomm Technologies IPQ806x-MAX98357A SoundCard + +This node models a soundcard for boards with the Qualcomm Technologies IPQ806x +SOC connected to a MAX98357A DAC via I2S. + +Required properties: + +- compatible : "qcom,ipq806x-max98357a" +- qcom,model : The user-visible name of this sound card. +- cpu : Phandle of the CPU DAI +- codec : Phandle of the codec DAI +- codec-dai : Name of the codec DAI which must be selected from one of the + following entries: + * max98357a + +Example: + +sound { + compatible = "qcom,ipq806x-max98357a"; + model = "ipq806x-max98357a"; + cpu = <&lpass_cpu>; + codec = <&max98357a>; + codec-dai = "max98357a"; +};
From: Kenneth Westfield kwestfie@codeaurora.org
Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- sound/soc/codecs/Kconfig | 4 ++ sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max98357a.c | 145 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 sound/soc/codecs/max98357a.c
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 8349f982a586841a3ac9e7b0526af05699c7deaf..0500b3ed5fa5ac4d45663ad659da9db3003bc5a3 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -69,6 +69,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_MAX98088 if I2C select SND_SOC_MAX98090 if I2C select SND_SOC_MAX98095 if I2C + select SND_SOC_MAX98357A if GPIOLIB select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9768 if I2C select SND_SOC_MAX9877 if I2C @@ -456,6 +457,9 @@ config SND_SOC_MAX98090 config SND_SOC_MAX98095 tristate
+config SND_SOC_MAX98357A + tristate + config SND_SOC_MAX9850 tristate
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index bbdfd1e1c182f9ee102f532f391f522e77a8922b..69b8666d187a0e8d1e2a532e68e2509acc95da7e 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -64,6 +64,7 @@ snd-soc-max9768-objs := max9768.o snd-soc-max98088-objs := max98088.o snd-soc-max98090-objs := max98090.o snd-soc-max98095-objs := max98095.o +snd-soc-max98357a-objs := max98357a.o snd-soc-max9850-objs := max9850.o snd-soc-mc13783-objs := mc13783.o snd-soc-ml26124-objs := ml26124.o @@ -245,6 +246,7 @@ obj-$(CONFIG_SND_SOC_MAX9768) += snd-soc-max9768.o obj-$(CONFIG_SND_SOC_MAX98088) += snd-soc-max98088.o obj-$(CONFIG_SND_SOC_MAX98090) += snd-soc-max98090.o obj-$(CONFIG_SND_SOC_MAX98095) += snd-soc-max98095.o +obj-$(CONFIG_SND_SOC_MAX98357A) += snd-soc-max98357a.o obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_MC13783) += snd-soc-mc13783.o obj-$(CONFIG_SND_SOC_ML26124) += snd-soc-ml26124.o diff --git a/sound/soc/codecs/max98357a.c b/sound/soc/codecs/max98357a.c new file mode 100644 index 0000000000000000000000000000000000000000..4ee23fbc4e1237268ae104319a9cfe4fc369934e --- /dev/null +++ b/sound/soc/codecs/max98357a.c @@ -0,0 +1,145 @@ +/* Copyright (c) 2010-2011,2013-2015 The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * max98357a.c -- MAX98357A ALSA SoC Codec driver + */ + +#include <linux/device.h> +#include <linux/err.h> +#include <linux/gpio.h> +#include <linux/gpio/consumer.h> +#include <linux/kernel.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <sound/pcm.h> +#include <sound/soc.h> +#include <sound/soc-dai.h> +#include <sound/soc-dapm.h> + +static int max98357a_daiops_trigger(struct snd_pcm_substream *substream, + int cmd, struct snd_soc_dai *dai) +{ + struct gpio_desc *sdmode = snd_soc_dai_get_drvdata(dai); + + switch (cmd) { + case SNDRV_PCM_TRIGGER_START: + case SNDRV_PCM_TRIGGER_RESUME: + case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: + gpiod_set_value(sdmode, 1); + break; + case SNDRV_PCM_TRIGGER_STOP: + case SNDRV_PCM_TRIGGER_SUSPEND: + case SNDRV_PCM_TRIGGER_PAUSE_PUSH: + gpiod_set_value(sdmode, 0); + break; + } + + return 0; +} + +static const struct snd_soc_dapm_widget max98357a_dapm_widgets[] = { + SND_SOC_DAPM_DAC("SDMode", NULL, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_OUTPUT("Speaker"), +}; + +static const struct snd_soc_dapm_route max98357a_dapm_routes[] = { + {"Speaker", NULL, "SDMode"}, +}; + +static int max98357a_codec_probe(struct snd_soc_codec *codec) +{ + struct gpio_desc *sdmode; + + sdmode = devm_gpiod_get(codec->dev, "sdmode"); + if (IS_ERR(sdmode)) { + dev_err(codec->dev, "%s() unable to get sdmode GPIO: %ld\n", + __func__, PTR_ERR(sdmode)); + return PTR_ERR(sdmode); + } + gpiod_direction_output(sdmode, 0); + snd_soc_codec_set_drvdata(codec, sdmode); + + return 0; +} + +static struct snd_soc_codec_driver max98357a_codec_driver = { + .probe = max98357a_codec_probe, + .dapm_widgets = max98357a_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(max98357a_dapm_widgets), + .dapm_routes = max98357a_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(max98357a_dapm_routes), +}; + +static struct snd_soc_dai_ops max98357a_dai_ops = { + .trigger = max98357a_daiops_trigger, +}; + +static struct snd_soc_dai_driver max98357a_dai_driver = { + .name = "max98357a", + .playback = { + .stream_name = "max98357a-playback", + .formats = SNDRV_PCM_FMTBIT_S16 | + SNDRV_PCM_FMTBIT_S24 | + SNDRV_PCM_FMTBIT_S32, + .rates = SNDRV_PCM_RATE_8000 | + SNDRV_PCM_RATE_16000 | + SNDRV_PCM_RATE_48000 | + SNDRV_PCM_RATE_96000, + .rate_min = 8000, + .rate_max = 96000, + .channels_min = 1, + .channels_max = 2, + }, + .ops = &max98357a_dai_ops, +}; + +static int max98357a_platform_probe(struct platform_device *pdev) +{ + int ret; + + ret = snd_soc_register_codec(&pdev->dev, &max98357a_codec_driver, + &max98357a_dai_driver, 1); + if (ret) + dev_err(&pdev->dev, "%s() error registering codec driver: %d\n", + __func__, ret); + + return ret; +} + +static int max98357a_platform_remove(struct platform_device *pdev) +{ + snd_soc_unregister_codec(&pdev->dev); + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id max98357a_device_id[] = { + { .compatible = "maxim,max98357a" }, + {} +}; +MODULE_DEVICE_TABLE(of, max98357a_device_id); +#endif + +static struct platform_driver max98357a_platform_driver = { + .driver = { + .name = "max98357a", + .of_match_table = of_match_ptr(max98357a_device_id), + }, + .probe = max98357a_platform_probe, + .remove = max98357a_platform_remove, +}; +module_platform_driver(max98357a_platform_driver); + +MODULE_DESCRIPTION("Maxim MAX98357A Codec Driver"); +MODULE_LICENSE("GPL v2");
On Wed, Feb 11, 2015 at 06:10:08PM -0800, Kenneth Westfield wrote:
From: Kenneth Westfield kwestfie@codeaurora.org
Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org
sound/soc/codecs/Kconfig | 4 ++ sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max98357a.c | 145 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 sound/soc/codecs/max98357a.c
Posted changes from V4 to V5 here: http://mailman.alsa-project.org/pipermail/alsa-devel/2015-February/087872.ht...
Please drop this patch.
From: Kenneth Westfield kwestfie@codeaurora.org
Add the CPU DAI driver for the Qualcomm Technologies low-power audio subsystem (LPASS).
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- sound/soc/qcom/lpass-cpu.c | 481 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 481 insertions(+) create mode 100644 sound/soc/qcom/lpass-cpu.c
diff --git a/sound/soc/qcom/lpass-cpu.c b/sound/soc/qcom/lpass-cpu.c new file mode 100644 index 0000000000000000000000000000000000000000..c178142989abce9c46565fccbaf3b140cb289b19 --- /dev/null +++ b/sound/soc/qcom/lpass-cpu.c @@ -0,0 +1,481 @@ +/* + * Copyright (c) 2010-2011,2013-2015 The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * lpass-cpu.c -- ALSA SoC CPU DAI driver for QTi LPASS + */ + +#include <linux/clk.h> +#include <linux/compiler.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <linux/regmap.h> +#include <sound/soc.h> +#include <sound/soc-dai.h> +#include "lpass-lpaif-ipq806x.h" +#include "lpass.h" + +static int lpass_cpu_daiops_set_sysclk(struct snd_soc_dai *dai, int clk_id, + unsigned int freq, int dir) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = clk_set_rate(drvdata->mi2s_osr_clk, freq); + if (ret) + dev_err(dai->dev, "%s() error setting mi2s osrclk to %u: %d\n", + __func__, freq, ret); + + return ret; +} + +static int lpass_cpu_daiops_startup(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = clk_prepare_enable(drvdata->mi2s_osr_clk); + if (ret) { + dev_err(dai->dev, "%s() error in enabling mi2s osr clk: %d\n", + __func__, ret); + return ret; + } + + ret = clk_prepare_enable(drvdata->mi2s_bit_clk); + if (ret) { + dev_err(dai->dev, "%s() error in enabling mi2s bit clk: %d\n", + __func__, ret); + clk_disable_unprepare(drvdata->mi2s_osr_clk); + return ret; + } + + return 0; +} + +static void lpass_cpu_daiops_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + + clk_disable_unprepare(drvdata->mi2s_bit_clk); + clk_disable_unprepare(drvdata->mi2s_osr_clk); +} + +static int lpass_cpu_daiops_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + snd_pcm_format_t format = params_format(params); + unsigned int channels = params_channels(params); + unsigned int rate = params_rate(params); + unsigned int regval; + int bitwidth, ret; + + bitwidth = snd_pcm_format_width(format); + if (bitwidth < 0) { + dev_err(dai->dev, "%s() invalid bit width given: %d\n", + __func__, bitwidth); + return bitwidth; + } + + regval = LPAIF_I2SCTL_LOOPBACK_DISABLE | + LPAIF_I2SCTL_WSSRC_INTERNAL; + + switch (bitwidth) { + case 16: + regval |= LPAIF_I2SCTL_BITWIDTH_16; + break; + case 24: + regval |= LPAIF_I2SCTL_BITWIDTH_24; + break; + case 32: + regval |= LPAIF_I2SCTL_BITWIDTH_32; + break; + default: + dev_err(dai->dev, "%s() invalid bitwidth given: %d\n", + __func__, bitwidth); + return -EINVAL; + } + + switch (channels) { + case 1: + regval |= LPAIF_I2SCTL_SPKMODE_SD0; + regval |= LPAIF_I2SCTL_SPKMONO_MONO; + break; + case 2: + regval |= LPAIF_I2SCTL_SPKMODE_SD0; + regval |= LPAIF_I2SCTL_SPKMONO_STEREO; + break; + case 4: + regval |= LPAIF_I2SCTL_SPKMODE_QUAD01; + regval |= LPAIF_I2SCTL_SPKMONO_STEREO; + break; + case 6: + regval |= LPAIF_I2SCTL_SPKMODE_6CH; + regval |= LPAIF_I2SCTL_SPKMONO_STEREO; + break; + case 8: + regval |= LPAIF_I2SCTL_SPKMODE_8CH; + regval |= LPAIF_I2SCTL_SPKMONO_STEREO; + break; + default: + dev_err(dai->dev, "%s() invalid channels given: %u\n", + __func__, channels); + return -EINVAL; + } + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_I2SCTL_REG(LPAIF_I2S_PORT_MI2S), regval); + if (ret) { + dev_err(dai->dev, "%s() error writing to i2sctl reg: %d\n", + __func__, ret); + return ret; + } + + ret = clk_set_rate(drvdata->mi2s_bit_clk, rate * bitwidth * 2); + if (ret) { + dev_err(dai->dev, "%s() error setting mi2s bitclk to %u: %d\n", + __func__, rate * bitwidth * 2, ret); + return ret; + } + + return 0; +} + +static int lpass_cpu_daiops_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_I2SCTL_REG(LPAIF_I2S_PORT_MI2S), 0); + if (ret) + dev_err(dai->dev, "%s() error writing to i2sctl reg: %d\n", + __func__, ret); + + return ret; +} + +static int lpass_cpu_daiops_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_I2SCTL_REG(LPAIF_I2S_PORT_MI2S), + LPAIF_I2SCTL_SPKEN_MASK, LPAIF_I2SCTL_SPKEN_ENABLE); + if (ret) + dev_err(dai->dev, "%s() error writing to i2sctl reg: %d\n", + __func__, ret); + + return ret; +} + +static int lpass_cpu_daiops_trigger(struct snd_pcm_substream *substream, + int cmd, struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + int ret; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_START: + case SNDRV_PCM_TRIGGER_RESUME: + case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_I2SCTL_REG(LPAIF_I2S_PORT_MI2S), + LPAIF_I2SCTL_SPKEN_MASK, + LPAIF_I2SCTL_SPKEN_ENABLE); + if (ret) + dev_err(dai->dev, "%s() error writing to i2sctl reg: %d\n", + __func__, ret); + break; + case SNDRV_PCM_TRIGGER_STOP: + case SNDRV_PCM_TRIGGER_SUSPEND: + case SNDRV_PCM_TRIGGER_PAUSE_PUSH: + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_I2SCTL_REG(LPAIF_I2S_PORT_MI2S), + LPAIF_I2SCTL_SPKEN_MASK, + LPAIF_I2SCTL_SPKEN_DISABLE); + if (ret) + dev_err(dai->dev, "%s() error writing to i2sctl reg: %d\n", + __func__, ret); + break; + } + + return ret; +} + +static struct snd_soc_dai_ops lpass_cpu_dai_ops = { + .set_sysclk = lpass_cpu_daiops_set_sysclk, + .startup = lpass_cpu_daiops_startup, + .shutdown = lpass_cpu_daiops_shutdown, + .hw_params = lpass_cpu_daiops_hw_params, + .hw_free = lpass_cpu_daiops_hw_free, + .prepare = lpass_cpu_daiops_prepare, + .trigger = lpass_cpu_daiops_trigger, +}; + +static int lpass_cpu_dai_probe(struct snd_soc_dai *dai) +{ + struct lpass_data *drvdata = snd_soc_dai_get_drvdata(dai); + int ret; + + /* ensure audio hardware is disabled */ + ret = regmap_write(drvdata->lpaif_map, + LPAIF_I2SCTL_REG(LPAIF_I2S_PORT_MI2S), 0); + if (ret) + dev_err(dai->dev, "%s() error writing to i2sctl reg: %d\n", + __func__, ret); + + return ret; +} + +static struct snd_soc_dai_driver lpass_cpu_dai_driver = { + .playback = { + .stream_name = "lpass-cpu-playback", + .formats = SNDRV_PCM_FMTBIT_S16 | + SNDRV_PCM_FMTBIT_S24 | + SNDRV_PCM_FMTBIT_S32, + .rates = SNDRV_PCM_RATE_8000 | + SNDRV_PCM_RATE_16000 | + SNDRV_PCM_RATE_32000 | + SNDRV_PCM_RATE_48000 | + SNDRV_PCM_RATE_96000, + .rate_min = 8000, + .rate_max = 96000, + .channels_min = 1, + .channels_max = 8, + }, + .probe = &lpass_cpu_dai_probe, + .ops = &lpass_cpu_dai_ops, +}; + +static const struct snd_soc_component_driver lpass_cpu_comp_driver = { + .name = "lpass-cpu", +}; + +static bool lpass_cpu_regmap_writeable(struct device *dev, unsigned int reg) +{ + int i; + + for (i = 0; i < LPAIF_I2S_PORT_NUM; ++i) + if (reg == LPAIF_I2SCTL_REG(i)) + return true; + + for (i = 0; i < LPAIF_IRQ_PORT_NUM; ++i) { + if (reg == LPAIF_IRQEN_REG(i)) + return true; + if (reg == LPAIF_IRQCLEAR_REG(i)) + return true; + } + + for (i = 0; i < LPAIF_RDMA_CHAN_NUM; ++i) { + if (reg == LPAIF_RDMACTL_REG(i)) + return true; + if (reg == LPAIF_RDMABASE_REG(i)) + return true; + if (reg == LPAIF_RDMABUFF_REG(i)) + return true; + if (reg == LPAIF_RDMAPER_REG(i)) + return true; + } + + return false; +} + +static bool lpass_cpu_regmap_readable(struct device *dev, unsigned int reg) +{ + int i; + + for (i = 0; i < LPAIF_I2S_PORT_NUM; ++i) + if (reg == LPAIF_I2SCTL_REG(i)) + return true; + + for (i = 0; i < LPAIF_IRQ_PORT_NUM; ++i) { + if (reg == LPAIF_IRQEN_REG(i)) + return true; + if (reg == LPAIF_IRQSTAT_REG(i)) + return true; + } + + for (i = 0; i < LPAIF_RDMA_CHAN_NUM; ++i) { + if (reg == LPAIF_RDMACTL_REG(i)) + return true; + if (reg == LPAIF_RDMABASE_REG(i)) + return true; + if (reg == LPAIF_RDMABUFF_REG(i)) + return true; + if (reg == LPAIF_RDMACURR_REG(i)) + return true; + if (reg == LPAIF_RDMAPER_REG(i)) + return true; + } + + return false; +} + +static bool lpass_cpu_regmap_volatile(struct device *dev, unsigned int reg) +{ + int i; + + for (i = 0; i < LPAIF_IRQ_PORT_NUM; ++i) + if (reg == LPAIF_IRQSTAT_REG(i)) + return true; + + for (i = 0; i < LPAIF_RDMA_CHAN_NUM; ++i) + if (reg == LPAIF_RDMACURR_REG(i)) + return true; + + return false; +} + +static const struct regmap_config lpass_cpu_regmap_config = { + .reg_bits = 32, + .reg_stride = 4, + .val_bits = 32, + .max_register = LPAIF_RDMAPER_REG(LPAIF_RDMA_CHAN_MAX), + .writeable_reg = lpass_cpu_regmap_writeable, + .readable_reg = lpass_cpu_regmap_readable, + .volatile_reg = lpass_cpu_regmap_volatile, + .cache_type = REGCACHE_FLAT, +}; + +static int lpass_cpu_platform_probe(struct platform_device *pdev) +{ + struct lpass_data *drvdata; + struct resource *res; + int ret; + + drvdata = devm_kzalloc(&pdev->dev, sizeof(struct lpass_data), + GFP_KERNEL); + if (!drvdata) + return -ENOMEM; + platform_set_drvdata(pdev, drvdata); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "lpass-lpaif"); + if (!res) { + dev_err(&pdev->dev, "%s() error getting resource\n", __func__); + return -ENODEV; + } + + drvdata->lpaif = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR((void const __force *)drvdata->lpaif)) { + dev_err(&pdev->dev, "%s() error mapping reg resource: %ld\n", + __func__, + PTR_ERR((void const __force *)drvdata->lpaif)); + return PTR_ERR((void const __force *)drvdata->lpaif); + } + + drvdata->lpaif_map = devm_regmap_init_mmio(&pdev->dev, drvdata->lpaif, + &lpass_cpu_regmap_config); + if (IS_ERR(drvdata->lpaif_map)) { + dev_err(&pdev->dev, "%s() error initializing regmap: %ld\n", + __func__, PTR_ERR(drvdata->lpaif_map)); + return PTR_ERR(drvdata->lpaif_map); + } + + drvdata->mi2s_osr_clk = devm_clk_get(&pdev->dev, "mi2s-osr-clk"); + if (IS_ERR(drvdata->mi2s_osr_clk)) { + dev_err(&pdev->dev, "%s() error getting mi2s-osr-clk: %ld\n", + __func__, PTR_ERR(drvdata->mi2s_osr_clk)); + return PTR_ERR(drvdata->mi2s_osr_clk); + } + + drvdata->mi2s_bit_clk = devm_clk_get(&pdev->dev, "mi2s-bit-clk"); + if (IS_ERR(drvdata->mi2s_bit_clk)) { + dev_err(&pdev->dev, "%s() error getting mi2s-bit-clk: %ld\n", + __func__, PTR_ERR(drvdata->mi2s_bit_clk)); + return PTR_ERR(drvdata->mi2s_bit_clk); + } + + drvdata->ahbix_clk = devm_clk_get(&pdev->dev, "ahbix-clk"); + if (IS_ERR(drvdata->ahbix_clk)) { + dev_err(&pdev->dev, "%s() error getting ahbix-clk: %ld\n", + __func__, PTR_ERR(drvdata->ahbix_clk)); + return PTR_ERR(drvdata->ahbix_clk); + } + + ret = clk_set_rate(drvdata->ahbix_clk, LPASS_AHBIX_CLOCK_FREQUENCY); + if (ret) { + dev_err(&pdev->dev, "%s() error setting rate on ahbix_clk: %d\n", + __func__, ret); + return ret; + } + + ret = clk_prepare_enable(drvdata->ahbix_clk); + if (ret) { + dev_err(&pdev->dev, "%s() Error enabling ahbix_clk: %d\n", + __func__, ret); + return ret; + } + + ret = devm_snd_soc_register_component(&pdev->dev, + &lpass_cpu_comp_driver, &lpass_cpu_dai_driver, 1); + if (ret) { + dev_err(&pdev->dev, "%s() error registering cpu driver: %d\n", + __func__, ret); + goto err_clk; + } + + ret = asoc_qcom_lpass_platform_register(pdev); + if (ret) { + dev_err(&pdev->dev, "%s() error registering platform driver: %d\n", + __func__, ret); + goto err_clk; + } + + return 0; + +err_clk: + clk_disable_unprepare(drvdata->ahbix_clk); + return ret; +} + +static int lpass_cpu_platform_remove(struct platform_device *pdev) +{ + struct lpass_data *drvdata = platform_get_drvdata(pdev); + + clk_disable_unprepare(drvdata->ahbix_clk); + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id lpass_cpu_device_id[] = { + { .compatible = "qcom,lpass-cpu" }, + {} +}; +MODULE_DEVICE_TABLE(of, lpass_cpu_device_id); +#endif + +static struct platform_driver lpass_cpu_platform_driver = { + .driver = { + .name = "lpass-cpu", + .of_match_table = of_match_ptr(lpass_cpu_device_id), + }, + .probe = lpass_cpu_platform_probe, + .remove = lpass_cpu_platform_remove, +}; +module_platform_driver(lpass_cpu_platform_driver); + +MODULE_DESCRIPTION("QTi LPASS CPU Driver"); +MODULE_LICENSE("GPL v2");
From: Kenneth Westfield kwestfie@codeaurora.org
Add platform driver for the Qualcomm Technologies low-power audio subsystem (LPASS) ports.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- sound/soc/qcom/lpass-platform.c | 526 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 526 insertions(+) create mode 100644 sound/soc/qcom/lpass-platform.c
diff --git a/sound/soc/qcom/lpass-platform.c b/sound/soc/qcom/lpass-platform.c new file mode 100644 index 0000000000000000000000000000000000000000..2fa6280dfb234b213904ad73dfad91c7f575538c --- /dev/null +++ b/sound/soc/qcom/lpass-platform.c @@ -0,0 +1,526 @@ +/* + * Copyright (c) 2010-2011,2013-2015 The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * lpass-platform.c -- ALSA SoC platform driver for QTi LPASS + */ + +#include <linux/compiler.h> +#include <linux/device.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/export.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/io.h> +#include <linux/platform_device.h> +#include <sound/memalloc.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <linux/regmap.h> +#include <sound/soc.h> +#include "lpass-lpaif-ipq806x.h" +#include "lpass.h" + +#define LPASS_PLATFORM_BUFFER_SIZE (16 * 1024) +#define LPASS_PLATFORM_PERIODS 2 + +static struct snd_pcm_hardware lpass_platform_pcm_hardware = { + .info = SNDRV_PCM_INFO_MMAP | + SNDRV_PCM_INFO_MMAP_VALID | + SNDRV_PCM_INFO_INTERLEAVED | + SNDRV_PCM_INFO_PAUSE | + SNDRV_PCM_INFO_RESUME, + .formats = SNDRV_PCM_FMTBIT_S16 | + SNDRV_PCM_FMTBIT_S24 | + SNDRV_PCM_FMTBIT_S32, + .rates = SNDRV_PCM_RATE_8000_192000, + .rate_min = 8000, + .rate_max = 192000, + .channels_min = 1, + .channels_max = 8, + .buffer_bytes_max = LPASS_PLATFORM_BUFFER_SIZE, + .period_bytes_max = LPASS_PLATFORM_BUFFER_SIZE / + LPASS_PLATFORM_PERIODS, + .period_bytes_min = LPASS_PLATFORM_BUFFER_SIZE / + LPASS_PLATFORM_PERIODS, + .periods_min = LPASS_PLATFORM_PERIODS, + .periods_max = LPASS_PLATFORM_PERIODS, + .fifo_size = 0, +}; + +static int lpass_platform_pcmops_open(struct snd_pcm_substream *substream) +{ + struct snd_pcm_runtime *runtime = substream->runtime; + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + int ret; + + snd_soc_set_runtime_hwparams(substream, &lpass_platform_pcm_hardware); + + runtime->dma_bytes = lpass_platform_pcm_hardware.buffer_bytes_max; + + ret = snd_pcm_hw_constraint_integer(runtime, + SNDRV_PCM_HW_PARAM_PERIODS); + if (ret < 0) { + dev_err(soc_runtime->dev, "%s() setting constraints failed: %d\n", + __func__, ret); + return -EINVAL; + } + + snd_pcm_set_runtime_buffer(substream, &substream->dma_buffer); + + return 0; +} + +static int lpass_platform_pcmops_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + snd_pcm_format_t format = params_format(params); + unsigned int channels = params_channels(params); + unsigned int regval; + int bitwidth; + int ret; + + bitwidth = snd_pcm_format_width(format); + if (bitwidth < 0) { + dev_err(soc_runtime->dev, "%s() invalid bit width given: %d\n", + __func__, bitwidth); + return bitwidth; + } + + regval = LPAIF_RDMACTL_BURSTEN_INCR4 | + LPAIF_RDMACTL_AUDINTF_MI2S | + LPAIF_RDMACTL_FIFOWM_8; + + switch (bitwidth) { + case 16: + switch (channels) { + case 1: + case 2: + regval |= LPAIF_RDMACTL_WPSCNT_ONE; + break; + case 4: + regval |= LPAIF_RDMACTL_WPSCNT_TWO; + break; + case 6: + regval |= LPAIF_RDMACTL_WPSCNT_THREE; + break; + case 8: + regval |= LPAIF_RDMACTL_WPSCNT_FOUR; + break; + default: + dev_err(soc_runtime->dev, "%s() invalid PCM config given: bw=%d, ch=%u\n", + __func__, bitwidth, channels); + return -EINVAL; + } + break; + case 24: + case 32: + switch (channels) { + case 1: + regval |= LPAIF_RDMACTL_WPSCNT_ONE; + break; + case 2: + regval |= LPAIF_RDMACTL_WPSCNT_TWO; + break; + case 4: + regval |= LPAIF_RDMACTL_WPSCNT_FOUR; + break; + case 6: + regval |= LPAIF_RDMACTL_WPSCNT_SIX; + break; + case 8: + regval |= LPAIF_RDMACTL_WPSCNT_EIGHT; + break; + default: + dev_err(soc_runtime->dev, "%s() invalid PCM config given: bw=%d, ch=%u\n", + __func__, bitwidth, channels); + return -EINVAL; + } + break; + default: + dev_err(soc_runtime->dev, "%s() invalid PCM config given: bw=%d, ch=%u\n", + __func__, bitwidth, channels); + return -EINVAL; + } + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_RDMACTL_REG(LPAIF_RDMA_CHAN_MI2S), regval); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmactl reg: %d\n", + __func__, ret); + return ret; + } + + return 0; +} + +static int lpass_platform_pcmops_hw_free(struct snd_pcm_substream *substream) +{ + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + int ret; + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_RDMACTL_REG(LPAIF_RDMA_CHAN_MI2S), 0); + if (ret) + dev_err(soc_runtime->dev, "%s() error writing to rdmactl reg: %d\n", + __func__, ret); + + return ret; +} + +static int lpass_platform_pcmops_prepare(struct snd_pcm_substream *substream) +{ + struct snd_pcm_runtime *runtime = substream->runtime; + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + int ret; + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_RDMABASE_REG(LPAIF_RDMA_CHAN_MI2S), + runtime->dma_addr); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmabase reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_RDMABUFF_REG(LPAIF_RDMA_CHAN_MI2S), + (snd_pcm_lib_buffer_bytes(substream) >> 2) - 1); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmabuff reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_write(drvdata->lpaif_map, + LPAIF_RDMAPER_REG(LPAIF_RDMA_CHAN_MI2S), + (snd_pcm_lib_period_bytes(substream) >> 2) - 1); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmaper reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_RDMACTL_REG(LPAIF_RDMA_CHAN_MI2S), + LPAIF_RDMACTL_ENABLE_MASK, LPAIF_RDMACTL_ENABLE_ON); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmactl reg: %d\n", + __func__, ret); + return ret; + } + + return 0; +} + +static int lpass_platform_pcmops_trigger(struct snd_pcm_substream *substream, + int cmd) +{ + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + int ret; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_START: + case SNDRV_PCM_TRIGGER_RESUME: + case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: + /* clear status before enabling interrupts */ + ret = regmap_write(drvdata->lpaif_map, + LPAIF_IRQCLEAR_REG(LPAIF_IRQ_PORT_HOST), + LPAIF_IRQ_ALL(LPAIF_RDMA_CHAN_MI2S)); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to irqclear reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_IRQEN_REG(LPAIF_IRQ_PORT_HOST), + LPAIF_IRQ_ALL(LPAIF_RDMA_CHAN_MI2S), + LPAIF_IRQ_ALL(LPAIF_RDMA_CHAN_MI2S)); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to irqen reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_RDMACTL_REG(LPAIF_RDMA_CHAN_MI2S), + LPAIF_RDMACTL_ENABLE_MASK, + LPAIF_RDMACTL_ENABLE_ON); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmactl reg: %d\n", + __func__, ret); + return ret; + } + break; + case SNDRV_PCM_TRIGGER_STOP: + case SNDRV_PCM_TRIGGER_SUSPEND: + case SNDRV_PCM_TRIGGER_PAUSE_PUSH: + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_RDMACTL_REG(LPAIF_RDMA_CHAN_MI2S), + LPAIF_RDMACTL_ENABLE_MASK, + LPAIF_RDMACTL_ENABLE_OFF); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmactl reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_update_bits(drvdata->lpaif_map, + LPAIF_IRQEN_REG(LPAIF_IRQ_PORT_HOST), + LPAIF_IRQ_ALL(LPAIF_RDMA_CHAN_MI2S), 0); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to irqen reg: %d\n", + __func__, ret); + return ret; + } + break; + } + + return 0; +} + +static snd_pcm_uframes_t lpass_platform_pcmops_pointer( + struct snd_pcm_substream *substream) +{ + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + unsigned int base_addr, curr_addr; + int ret; + + ret = regmap_read(drvdata->lpaif_map, + LPAIF_RDMABASE_REG(LPAIF_RDMA_CHAN_MI2S), &base_addr); + if (ret) { + dev_err(soc_runtime->dev, "%s() error reading from rdmabase reg: %d\n", + __func__, ret); + return ret; + } + + ret = regmap_read(drvdata->lpaif_map, + LPAIF_RDMACURR_REG(LPAIF_RDMA_CHAN_MI2S), &curr_addr); + if (ret) { + dev_err(soc_runtime->dev, "%s() error reading from rdmacurr reg: %d\n", + __func__, ret); + return ret; + } + + return bytes_to_frames(substream->runtime, curr_addr - base_addr); +} + +static int lpass_platform_pcmops_mmap(struct snd_pcm_substream *substream, + struct vm_area_struct *vma) +{ + struct snd_pcm_runtime *runtime = substream->runtime; + + return dma_mmap_coherent(substream->pcm->card->dev, vma, + runtime->dma_area, runtime->dma_addr, + runtime->dma_bytes); +} + +static struct snd_pcm_ops lpass_platform_pcm_ops = { + .open = lpass_platform_pcmops_open, + .ioctl = snd_pcm_lib_ioctl, + .hw_params = lpass_platform_pcmops_hw_params, + .hw_free = lpass_platform_pcmops_hw_free, + .prepare = lpass_platform_pcmops_prepare, + .trigger = lpass_platform_pcmops_trigger, + .pointer = lpass_platform_pcmops_pointer, + .mmap = lpass_platform_pcmops_mmap, +}; + +static irqreturn_t lpass_platform_lpaif_irq(int irq, void *data) +{ + struct snd_pcm_substream *substream = data; + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + unsigned int interrupts; + irqreturn_t ret = IRQ_NONE; + int rv; + + rv = regmap_read(drvdata->lpaif_map, + LPAIF_IRQSTAT_REG(LPAIF_IRQ_PORT_HOST), &interrupts); + if (rv) { + dev_err(soc_runtime->dev, "%s() error reading from irqstat reg: %d\n", + __func__, rv); + return IRQ_NONE; + } + interrupts &= LPAIF_IRQ_ALL(LPAIF_RDMA_CHAN_MI2S); + + if (interrupts & LPAIF_IRQ_PER(LPAIF_RDMA_CHAN_MI2S)) { + rv = regmap_write(drvdata->lpaif_map, + LPAIF_IRQCLEAR_REG(LPAIF_IRQ_PORT_HOST), + LPAIF_IRQ_PER(LPAIF_RDMA_CHAN_MI2S)); + if (rv) { + dev_err(soc_runtime->dev, "%s() error writing to irqclear reg: %d\n", + __func__, rv); + return IRQ_NONE; + } + snd_pcm_period_elapsed(substream); + ret = IRQ_HANDLED; + } + + if (interrupts & LPAIF_IRQ_XRUN(LPAIF_RDMA_CHAN_MI2S)) { + rv = regmap_write(drvdata->lpaif_map, + LPAIF_IRQCLEAR_REG(LPAIF_IRQ_PORT_HOST), + LPAIF_IRQ_XRUN(LPAIF_RDMA_CHAN_MI2S)); + if (rv) { + dev_err(soc_runtime->dev, "%s() error writing to irqclear reg: %d\n", + __func__, rv); + return IRQ_NONE; + } + dev_warn(soc_runtime->dev, "%s() xrun warning\n", __func__); + snd_pcm_stop(substream, SNDRV_PCM_STATE_XRUN); + ret = IRQ_HANDLED; + } + + if (interrupts & LPAIF_IRQ_ERR(LPAIF_RDMA_CHAN_MI2S)) { + rv = regmap_write(drvdata->lpaif_map, + LPAIF_IRQCLEAR_REG(LPAIF_IRQ_PORT_HOST), + LPAIF_IRQ_ERR(LPAIF_RDMA_CHAN_MI2S)); + if (rv) { + dev_err(soc_runtime->dev, "%s() error writing to irqclear reg: %d\n", + __func__, rv); + return IRQ_NONE; + } + dev_err(soc_runtime->dev, "%s() bus access error\n", __func__); + snd_pcm_stop(substream, SNDRV_PCM_STATE_DISCONNECTED); + ret = IRQ_HANDLED; + } + + return ret; +} + +static int lpass_platform_alloc_buffer(struct snd_pcm_substream *substream, + struct snd_soc_pcm_runtime *soc_runtime) +{ + struct snd_dma_buffer *buf = &substream->dma_buffer; + size_t size = lpass_platform_pcm_hardware.buffer_bytes_max; + + buf->dev.type = SNDRV_DMA_TYPE_DEV; + buf->dev.dev = soc_runtime->dev; + buf->private_data = NULL; + buf->area = dma_alloc_coherent(soc_runtime->dev, size, &buf->addr, + GFP_KERNEL); + if (!buf->area) { + dev_err(soc_runtime->dev, "%s: Could not allocate DMA buffer\n", + __func__); + return -ENOMEM; + } + buf->bytes = size; + + return 0; +} + +static void lpass_platform_free_buffer(struct snd_pcm_substream *substream, + struct snd_soc_pcm_runtime *soc_runtime) +{ + struct snd_dma_buffer *buf = &substream->dma_buffer; + + if (buf->area) { + dma_free_coherent(soc_runtime->dev, buf->bytes, buf->area, + buf->addr); + } + buf->area = NULL; +} + +static int lpass_platform_pcm_new(struct snd_soc_pcm_runtime *soc_runtime) +{ + struct snd_pcm *pcm = soc_runtime->pcm; + struct snd_pcm_substream *substream = + pcm->streams[SNDRV_PCM_STREAM_PLAYBACK].substream; + struct lpass_data *drvdata = + snd_soc_platform_get_drvdata(soc_runtime->platform); + int ret; + + soc_runtime->dev->coherent_dma_mask = DMA_BIT_MASK(32); + soc_runtime->dev->dma_mask = &soc_runtime->dev->coherent_dma_mask; + + ret = lpass_platform_alloc_buffer(substream, soc_runtime); + if (ret) + return ret; + + ret = devm_request_irq(soc_runtime->dev, drvdata->lpaif_irq, + lpass_platform_lpaif_irq, IRQF_TRIGGER_RISING, + "lpass-irq-lpaif", substream); + if (ret) { + dev_err(soc_runtime->dev, "%s() irq request failed: %d\n", + __func__, ret); + goto err_buf; + } + + /* ensure audio hardware is disabled */ + ret = regmap_write(drvdata->lpaif_map, + LPAIF_IRQEN_REG(LPAIF_IRQ_PORT_HOST), 0); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to irqen reg: %d\n", + __func__, ret); + return ret; + } + ret = regmap_write(drvdata->lpaif_map, + LPAIF_RDMACTL_REG(LPAIF_RDMA_CHAN_MI2S), 0); + if (ret) { + dev_err(soc_runtime->dev, "%s() error writing to rdmactl reg: %d\n", + __func__, ret); + return ret; + } + + return 0; + +err_buf: + lpass_platform_free_buffer(substream, soc_runtime); + return ret; +} + +static void lpass_platform_pcm_free(struct snd_pcm *pcm) +{ + struct snd_pcm_substream *substream = + pcm->streams[SNDRV_PCM_STREAM_PLAYBACK].substream; + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + + lpass_platform_free_buffer(substream, soc_runtime); +} + +static struct snd_soc_platform_driver lpass_platform_driver = { + .pcm_new = lpass_platform_pcm_new, + .pcm_free = lpass_platform_pcm_free, + .ops = &lpass_platform_pcm_ops, +}; + +int asoc_qcom_lpass_platform_register(struct platform_device *pdev) +{ + struct lpass_data *drvdata = platform_get_drvdata(pdev); + + drvdata->lpaif_irq = platform_get_irq_byname(pdev, "lpass-irq-lpaif"); + if (drvdata->lpaif_irq < 0) { + dev_err(&pdev->dev, "%s() error getting irq handle: %d\n", + __func__, drvdata->lpaif_irq); + return -ENODEV; + } + + return devm_snd_soc_register_platform(&pdev->dev, + &lpass_platform_driver); +} +EXPORT_SYMBOL_GPL(asoc_qcom_lpass_platform_register); + +MODULE_DESCRIPTION("QTi LPASS Platform Driver"); +MODULE_LICENSE("GPL v2");
From: Kenneth Westfield kwestfie@codeaurora.org
Add machine driver for the boards with the IPQ806X SOC connected to the MAX98357A DAC.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- sound/soc/qcom/ipq806x-max98357a.c | 171 +++++++++++++++++++++++++++++++++++++ 1 file changed, 171 insertions(+) create mode 100644 sound/soc/qcom/ipq806x-max98357a.c
diff --git a/sound/soc/qcom/ipq806x-max98357a.c b/sound/soc/qcom/ipq806x-max98357a.c new file mode 100644 index 0000000000000000000000000000000000000000..af92e9ffa42104d6e29160b9e0ffedc820388c7c --- /dev/null +++ b/sound/soc/qcom/ipq806x-max98357a.c @@ -0,0 +1,171 @@ +/* + * Copyright (c) 2010-2011,2013-2015 The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * ipq806x-max98357a.c -- ALSA SoC machine driver for QTi ipq806x SOC with + * MAX98357a DAC + */ + +#include <linux/device.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/mod_devicetable.h> +#include <linux/platform_device.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> + +#define IPQ806X_MAX98357A_SYSCLK_MULT 4 + +static int ipq806x_max98357a_ops_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_pcm_runtime *soc_runtime = substream->private_data; + struct snd_soc_card *card = soc_runtime->card; + snd_pcm_format_t format = params_format(params); + unsigned int rate = params_rate(params); + unsigned int sysclk_freq; + int bitwidth, ret; + + bitwidth = snd_pcm_format_width(format); + if (bitwidth < 0) { + dev_err(card->dev, "%s() invalid bit width given: %d\n", + __func__, bitwidth); + return bitwidth; + } + + /* + * as the CPU DAI is the I2S bus master and no system clock is needed by + * the MAX98357a DAC, simply set the system clock to be a constant + * multiple of the bit clock for the clock divider + */ + sysclk_freq = rate * bitwidth * 2 * IPQ806X_MAX98357A_SYSCLK_MULT; + + ret = snd_soc_dai_set_sysclk(soc_runtime->cpu_dai, 0, sysclk_freq, 0); + if (ret) { + dev_err(card->dev, "%s() error setting sysclk to %u: %d\n", + __func__, sysclk_freq, ret); + return ret; + } + + return 0; +} + +static struct snd_soc_ops ipq806x_max98357a_soc_ops = { + .hw_params = ipq806x_max98357a_ops_hw_params, +}; + +static struct snd_soc_dai_link ipq806x_max98357a_dai_link = { + .name = "IPQ806x Media1", + .stream_name = "MultiMedia1", + .ops = &ipq806x_max98357a_soc_ops, +}; + +static struct snd_soc_card ipq806x_max98357a_soc_card = { + .name = "ipq806x-max98357a", + .dev = NULL, +}; + +static int ipq806x_max98357a_parse_of(struct snd_soc_card *card) +{ + struct snd_soc_dai_link *dai_link = card->dai_link; + struct device_node *np = card->dev->of_node; + int ret; + + dai_link->cpu_of_node = of_parse_phandle(np, "cpu", 0); + if (!dai_link->cpu_of_node) { + dev_err(card->dev, "%s() error getting cpu phandle\n", + __func__); + return -EINVAL; + } + dai_link->platform_of_node = dai_link->cpu_of_node; + + dai_link->codec_of_node = of_parse_phandle(np, "codec", 0); + if (!dai_link->codec_of_node) { + dev_err(card->dev, "%s() error getting codec phandle\n", + __func__); + return -EINVAL; + } + + ret = of_property_read_string(np, "codec-dai", + &dai_link->codec_dai_name); + if (ret) { + dev_err(card->dev, "%s() error getting codec-dai: %d\n", + __func__, ret); + return -EINVAL; + } + + return 0; +} + +static int ipq806x_max98357a_platform_probe(struct platform_device *pdev) +{ + struct snd_soc_card *card = &ipq806x_max98357a_soc_card; + int ret; + + if (card->dev) { + dev_err(&pdev->dev, "%s() error, existing soundcard\n", + __func__); + return -ENODEV; + } + card->dev = &pdev->dev; + platform_set_drvdata(pdev, card); + + ret = snd_soc_of_parse_card_name(card, "qcom,model"); + if (ret) { + dev_err(&pdev->dev, "%s() error parsing card name: %d\n", + __func__, ret); + return ret; + } + + card->dai_link = &ipq806x_max98357a_dai_link; + card->num_links = 1; + + ret = ipq806x_max98357a_parse_of(card); + if (ret) { + dev_err(&pdev->dev, "%s() error resolving dai links: %d\n", + __func__, ret); + return ret; + } + + ret = devm_snd_soc_register_card(&pdev->dev, card); + if (ret == -EPROBE_DEFER) { + card->dev = NULL; + return ret; + } else if (ret) { + dev_err(&pdev->dev, "%s() error registering soundcard: %d\n", + __func__, ret); + return ret; + } + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id ipq806x_max98357a_device_id[] = { + { .compatible = "qcom,ipq806x-max98357a" }, + {}, +}; +MODULE_DEVICE_TABLE(of, ipq806x_max98357a_device_id); +#endif + +static struct platform_driver ipq806x_max98357a_platform_driver = { + .driver = { + .name = "ipq806x-max98357a", + .of_match_table = + of_match_ptr(ipq806x_max98357a_device_id), + }, + .probe = ipq806x_max98357a_platform_probe, +}; +module_platform_driver(ipq806x_max98357a_platform_driver); + +MODULE_DESCRIPTION("QTi ipq806x-max98357a Machine Driver"); +MODULE_LICENSE("GPL v2");
From: Kenneth Westfield kwestfie@codeaurora.org
Define the LPASS platform driver and the LPASS CPU DAI driver configuration, and how to build them.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- sound/soc/qcom/Kconfig | 26 ++++++++++++++++++++++++++ sound/soc/qcom/Makefile | 11 +++++++++++ 2 files changed, 37 insertions(+) create mode 100644 sound/soc/qcom/Kconfig create mode 100644 sound/soc/qcom/Makefile
diff --git a/sound/soc/qcom/Kconfig b/sound/soc/qcom/Kconfig new file mode 100644 index 0000000000000000000000000000000000000000..803fc204d65ae1916f30477bdaf926b650320c8a --- /dev/null +++ b/sound/soc/qcom/Kconfig @@ -0,0 +1,26 @@ +config SND_SOC_QCOM + tristate "SoC Audio support for QCOM platforms" + help + Support for audio in Qualcomm Technologies SOC-based systems. + Say Y if you want to use audio devices such as I2S, PCM, + S/PDIF, etc. + +config SND_SOC_LPASS_CPU + tristate + depends on SND_SOC_QCOM + +config SND_SOC_IPQ806X_MAX98357A + tristate "SoC Audio support for IPQ806x based platforms" + depends on SND_SOC_QCOM || ARCH_QCOM || COMPILE_TEST + select SND_SOC_LPASS_CPU + select SND_SOC_LPASS_PLATFORM + select SND_SOC_MAX98357A + help + Support for Qualcomm Technologies LPASS audio block in + IPQ806X SOC-based systems. + Say Y if you want to use audio devices such as I2S, PCM, + S/PDIF, etc. + +config SND_SOC_LPASS_PLATFORM + tristate + depends on SND_SOC_QCOM diff --git a/sound/soc/qcom/Makefile b/sound/soc/qcom/Makefile new file mode 100644 index 0000000000000000000000000000000000000000..b2811496b0df654a451c0dc231ab5bff84ca2850 --- /dev/null +++ b/sound/soc/qcom/Makefile @@ -0,0 +1,11 @@ +# Platform +snd-soc-lpass-cpu-objs := lpass-cpu.o +snd-soc-lpass-platform-objs := lpass-platform.o + +obj-$(CONFIG_SND_SOC_LPASS_CPU) += snd-soc-lpass-cpu.o +obj-$(CONFIG_SND_SOC_LPASS_PLATFORM) += snd-soc-lpass-platform.o + +# Machine +snd-soc-ipq806x-max98357a-objs := ipq806x-max98357a.o + +obj-$(CONFIG_SND_SOC_IPQ806X_MAX98357A) += snd-soc-ipq806x-max98357a.o
From: Kenneth Westfield kwestfie@codeaurora.org
Allow for the Qualcomm Technologies ASoC drivers to build.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- sound/soc/Kconfig | 1 + sound/soc/Makefile | 1 + 2 files changed, 2 insertions(+)
diff --git a/sound/soc/Kconfig b/sound/soc/Kconfig index 7d5d6444a83737ffa3c01acbe1925de619e0390a..b98eebf0e30bba19ec24acc7f0e6ab155e5e602b 100644 --- a/sound/soc/Kconfig +++ b/sound/soc/Kconfig @@ -47,6 +47,7 @@ source "sound/soc/kirkwood/Kconfig" source "sound/soc/intel/Kconfig" source "sound/soc/mxs/Kconfig" source "sound/soc/pxa/Kconfig" +source "sound/soc/qcom/Kconfig" source "sound/soc/rockchip/Kconfig" source "sound/soc/samsung/Kconfig" source "sound/soc/sh/Kconfig" diff --git a/sound/soc/Makefile b/sound/soc/Makefile index 865e090c80616024a552da5e33d2796b9be1dbbd..3d78a8d874dc98dd6219b33e3f2c100ef0334bfc 100644 --- a/sound/soc/Makefile +++ b/sound/soc/Makefile @@ -28,6 +28,7 @@ obj-$(CONFIG_SND_SOC) += nuc900/ obj-$(CONFIG_SND_SOC) += omap/ obj-$(CONFIG_SND_SOC) += kirkwood/ obj-$(CONFIG_SND_SOC) += pxa/ +obj-$(CONFIG_SND_SOC) += qcom/ obj-$(CONFIG_SND_SOC) += rockchip/ obj-$(CONFIG_SND_SOC) += samsung/ obj-$(CONFIG_SND_SOC) += sh/
From: Kenneth Westfield kwestfie@codeaurora.org
Model the Qualcomm Technologies LPASS hardware for the ipq806x SOC.
Signed-off-by: Kenneth Westfield kwestfie@codeaurora.org Acked-by: Banajit Goswami bgoswami@codeaurora.org --- arch/arm/boot/dts/qcom-ipq8064.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index 63b2146f563b541e4994697af5ee1bbb41a4abd1..f9b1cf2737e61c5e428cfef19cfd013395138a52 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -2,6 +2,7 @@
#include "skeleton.dtsi" #include <dt-bindings/clock/qcom,gcc-ipq806x.h> +#include <dt-bindings/clock/qcom,lcc-ipq806x.h> #include <dt-bindings/soc/qcom,gsbi.h>
/ { @@ -96,6 +97,21 @@ cpu-offset = <0x80000>; };
+ lpass@28100000 { + compatible = "qcom,lpass-cpu"; + status = "disabled"; + clocks = <&lcc AHBIX_CLK>, + <&lcc MI2S_OSR_CLK>, + <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", + "mi2s-osr-clk", + "mi2s-bit-clk"; + interrupts = <0 85 1>; + interrupt-names = "lpass-irq-lpaif"; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + }; + acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; @@ -279,5 +295,12 @@ #clock-cells = <1>; #reset-cells = <1>; }; + + lcc: clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; }; };
participants (2)
-
Kenneth Westfield -
Mark Brown