[PATCH 1/2] ASoC: rt5645: Fix the electric noise due to the CBJ contacts floating
From: Derek Fang derek.fang@realtek.com
The codec leaves tie combo jack's sleeve/ring2 to floating status default. It would cause electric noise while connecting the active speaker jack during boot or shutdown. This patch requests a gpio to control the additional jack circuit to tie the contacts to the ground or floating.
Signed-off-by: Derek Fang derek.fang@realtek.com
diff --git a/sound/soc/codecs/rt5645.c b/sound/soc/codecs/rt5645.c index e3ba04484813..d0d24a53df74 100644 --- a/sound/soc/codecs/rt5645.c +++ b/sound/soc/codecs/rt5645.c @@ -444,6 +444,7 @@ struct rt5645_priv { struct regmap *regmap; struct i2c_client *i2c; struct gpio_desc *gpiod_hp_det; + struct gpio_desc *gpiod_cbj_sleeve; struct snd_soc_jack *hp_jack; struct snd_soc_jack *mic_jack; struct snd_soc_jack *btn_jack; @@ -3186,6 +3187,9 @@ static int rt5645_jack_detect(struct snd_soc_component *component, int jack_inse regmap_update_bits(rt5645->regmap, RT5645_IN1_CTRL2, RT5645_CBJ_MN_JD, 0);
+ if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 1); + msleep(600); regmap_read(rt5645->regmap, RT5645_IN1_CTRL3, &val); val &= 0x7; @@ -3202,6 +3206,8 @@ static int rt5645_jack_detect(struct snd_soc_component *component, int jack_inse snd_soc_dapm_disable_pin(dapm, "Mic Det Power"); snd_soc_dapm_sync(dapm); rt5645->jack_type = SND_JACK_HEADPHONE; + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); } if (rt5645->pdata.level_trigger_irq) regmap_update_bits(rt5645->regmap, RT5645_IRQ_CTRL2, @@ -3229,6 +3235,9 @@ static int rt5645_jack_detect(struct snd_soc_component *component, int jack_inse if (rt5645->pdata.level_trigger_irq) regmap_update_bits(rt5645->regmap, RT5645_IRQ_CTRL2, RT5645_JD_1_1_MASK, RT5645_JD_1_1_INV); + + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); }
return rt5645->jack_type; @@ -4012,6 +4021,16 @@ static int rt5645_i2c_probe(struct i2c_client *i2c) return ret; }
+ rt5645->gpiod_cbj_sleeve = devm_gpiod_get_optional(&i2c->dev, "cbj-sleeve", + GPIOD_OUT_LOW); + + if (IS_ERR(rt5645->gpiod_cbj_sleeve)) { + ret = PTR_ERR(rt5645->gpiod_cbj_sleeve); + dev_info(&i2c->dev, "failed to initialize gpiod, ret=%d\n", ret); + if (ret != -ENOENT) + return ret; + } + for (i = 0; i < ARRAY_SIZE(rt5645->supplies); i++) rt5645->supplies[i].supply = rt5645_supply_names[i];
@@ -4259,6 +4278,9 @@ static void rt5645_i2c_remove(struct i2c_client *i2c) cancel_delayed_work_sync(&rt5645->jack_detect_work); cancel_delayed_work_sync(&rt5645->rcclock_work);
+ if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); + regulator_bulk_disable(ARRAY_SIZE(rt5645->supplies), rt5645->supplies); }
@@ -4274,6 +4296,9 @@ static void rt5645_i2c_shutdown(struct i2c_client *i2c) 0); msleep(20); regmap_write(rt5645->regmap, RT5645_RESET, 0); + + if (rt5645->gpiod_cbj_sleeve) + gpiod_set_value(rt5645->gpiod_cbj_sleeve, 0); }
static int __maybe_unused rt5645_sys_suspend(struct device *dev)
From: Derek Fang derek.fang@realtek.com
Add an optional gpio property to control external CBJ circuits to avoid some electric noise caused by sleeve/ring2 contacts floating.
Signed-off-by: Derek Fang derek.fang@realtek.com
diff --git a/Documentation/devicetree/bindings/sound/rt5645.txt b/Documentation/devicetree/bindings/sound/rt5645.txt index 41a62fd2ae1f..c1fa379f5f3e 100644 --- a/Documentation/devicetree/bindings/sound/rt5645.txt +++ b/Documentation/devicetree/bindings/sound/rt5645.txt @@ -20,6 +20,11 @@ Optional properties: a GPIO spec for the external headphone detect pin. If jd-mode = 0, we will get the JD status by getting the value of hp-detect-gpios.
+- cbj-sleeve-gpios: + a GPIO spec to control the external combo jack circuit to tie the sleeve/ring2 + contacts to the ground or floating. It could avoid some electric noise from the + active speaker jacks. + - realtek,in2-differential Boolean. Indicate MIC2 input are differential, rather than single-ended.
@@ -68,6 +73,7 @@ codec: rt5650@1a { compatible = "realtek,rt5650"; reg = <0x1a>; hp-detect-gpios = <&gpio 19 0>; + cbj-sleeve-gpios = <&gpio 20 0>; interrupt-parent = <&gpio>; interrupts = <7 IRQ_TYPE_EDGE_FALLING>; realtek,dmic-en = "true";
On Mon, 08 Apr 2024 17:10:56 +0800, derek.fang@realtek.com wrote:
The codec leaves tie combo jack's sleeve/ring2 to floating status default. It would cause electric noise while connecting the active speaker jack during boot or shutdown. This patch requests a gpio to control the additional jack circuit to tie the contacts to the ground or floating.
[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/2] ASoC: rt5645: Fix the electric noise due to the CBJ contacts floating commit: 103abab975087e1f01b76fcb54c91dbb65dbc249 [2/2] ASoC: dt-bindings: rt5645: add cbj sleeve gpio property commit: 306b38e3fa727d22454a148a364123709e356600
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
participants (2)
-
derek.fang＠realtek.com -
Mark Brown