[alsa-devel] Open bugs
Hello,
The bugs listed are over a month old, and haven't been addressed yet. It would be appreciated if corresponding maintainers identify whether the bugs have been fixed, or need to be worked on, and take appropriate action.
In most cases, reporters are standing by and ready to provide information and necessary testing. Thanks!
Memory Management=======================================
swapping in 2.6.24-rc5-git3 http://bugzilla.kernel.org/show_bug.cgi?id=9592 Date: 12/07/2007 Regression Summary: # /proc/sys/vm# cat swappiness 0 but scp-ing 2GB file causes many processes are swapped out due to increase of the file cache size. Was looked at by Jan Kara jack@suse.cz; KAMEZAWA Hiroyuki kamezawa.hiroyu@jp.fujitsu.com - commented
I/O-Storage================================================
SATA DVD drive & UDF filesystem problem http://bugzilla.kernel.org/show_bug.cgi?id=9668 12/31/2007 Summary: I mount dvd discs (udf) with piix and ide_cd modules without problem (on hw decribed higher). Then I put NEC drive to new mainboard (ICH9 + jmicron SATA/PATA chips) and use ahci (jmicron) + sr_mod modules.
SCSI======================================================
Problems on booting http://bugzilla.kernel.org/show_bug.cgi?id=9621 Date: 12/22/2007 Regression Summary: The boot stops / hangs on hardware detection of SCSI. I have an InitioINI-9X00U/UW When I have an usb key sticked in /dev/sba, and run lilo then, then it dont boot but give L99 99 99 99 ... error
Resetting RAID attached to a FC Switch causes kernel panic and crash http://bugzilla.kernel.org/show_bug.cgi?id=9598 12/18/2007 Hardware Environment:SunFire X4200 - 2 x dual core AMD Opteron CPUs, 8GB Ram, Qlogic FC adapter. Summary: Resetting the RAID box causes the X4200 to crash.
3ware 9650SE -8LPML not recognized by 3w-9xxx driver http://bugzilla.kernel.org/show_bug.cgi?id=8908 08/19/2007 Problem Description: The 3w-9xxx kernel driver for 3ware 9xxx SATA RAID Controller series did not recognize the 3ware 9650SE-8LPML SATA RAID Controller.
Plarform===================================================
kexec buffer error http://bugzilla.kernel.org/show_bug.cgi?id=9693 Date: 01/04/2008 Regression Summary: Close of /boot/kernel-2.6.24-rc6-git11 failed: : buffer error kexec load failed, error = 1
20000+ wake-ups/second in 2.6.24 http://bugzilla.kernel.org/show_bug.cgi?id=9489 Date: 12/02/2007 Summary: "something" is causing the system to go into a state where the cpu throws us right out of the C-state the kernel asks for Discussed: Arjan van de Ven, Mark Lord
VIDEO/FB======================================================
No text consoles with FRAMEBUFFER_CONSOLE_DETECT_PRIMARY http://bugzilla.kernel.org/show_bug.cgi?id=9310 11/05/2007 still there Regression Summary: After initial boot messages all output to console stops. The last visible messages are: checking if image is initramfs...<6>Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 After that, nothing until XOrg starts up and graphical login/desktop on VT7are displayed normal.
DVB===========================================================
DVB-T Pluto2: SUSPEND/RESUME methods are missing for this driver 04/05/2007 - still present in 2.6.24 http://bugzilla.kernel.org/show_bug.cgi?id=8304 Summary: After SWSUPS resume, pluto2 card is not started properly, led getts not green and card is unable load tda firmware Hardware Environment: Acer TravelMate No one looked at it yet.
Several Pluto bug:
DVB-T Pluto2 && PCI: When playing in dmesg I often getts: "pluto2 0000:03:00.0: overflow irq (10)" Date: 11/08/2006 still there http://bugzilla.kernel.org/show_bug.cgi?id=7473 Hardware Environment: Acer TravelMate
DVB-T Pluto2: Getting tons of "card hung up :(" messages when card is removed from pcmcia slot Date: 11/08/2006 - still there http://bugzilla.kernel.org/show_bug.cgi?id=7472
DVB-T Pluto2: Unable to change MUX Date: 11/08/2006 http://bugzilla.kernel.org/show_bug.cgi?id=7471
KNC1 DVB-C cam module not working on driver load Date: 1/15/2007 - still there http://bugzilla.kernel.org/show_bug.cgi?id=7825 Error: DVB: registering new adapter (KNC1 DVB-C) adapter failed MAC signature check encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff KNC1-0: MAC addr = 00:09:d6:6d:5a:f0 TDA10021: i2c-addr = 0x0c, id = 0x7c DVB: registering frontend 0 (Philips TDA10021 DVB-C)... budget-av: ci interface initialised. budget-av: cam inserted A dvb_ca adaptor 0: PC card did not respond :(
build #341 failed for 2.6.24-rc6-g1842c7f in linux/./drivers/media/dvb/ttpci/budget-av.c 01/01/2008 http://bugzilla.kernel.org/show_bug.cgi?id=9671 Still there in 2.6.24.. has it been fixed?
DVB-USB UMT-010 driver has certain oops when installed 01/09/2008 http://bugzilla.kernel.org/show_bug.cgi?id=9720 In the umt-010 driver the struct umt_properties sets the number of URBs for transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10. This causes an oops for all devices which use the umt-010 chipset when they are inserted.
v4l Problem with dvb-usb and Hauppage USB Stick http://bugzilla.kernel.org/show_bug.cgi?id=9001 9/9/2007 x86_64 dvb-usb: Hauppauge Nova-T Stick crashes during channel search with Kaffeine
KEXEC=============================================================
kexec buffer error http://bugzilla.kernel.org/show_bug.cgi?id=9693 01/05/2008 2.6.24-rc6-git9 works as expected. git10 fails with root device not found
DRIVERS===========================================================
Two small bugs detected by code review:
physmap does not have a release() function 01/05/2008 http://bugzilla.kernel.org/show_bug.cgi?id=9690 Summary: Pretty trivial addition of the release()
hgafb module is broken & unmaintained http://bugzilla.kernel.org/show_bug.cgi?id=9689 This one also needs release() function
FILESYSTEMS======================================================
journal_data mount option causes filesystem corruption with blocksize != 4096 01/05/2008 http://bugzilla.kernel.org/show_bug.cgi?id=9692 Appears to be e2fsck problem
ALSA==============================================================
SC-5200 + wine = System freeze http://bugzilla.kernel.org/show_bug.cgi?id=9649 12/27/2007 -- Motherboard: Asus A8R-MVP -- Harddrive: Samsung 200Gb -- Soundcard 1: Onboard -- Soundcard 2: Trust SC-5200 Running any part of wine freezes up the whole system. Both SSH connections, the normal X screen and any other device, including sound played by for example music players, freezes up. After about 10 seconds the system reboots. By removing my second sound card it works. By disabling my onboard sound it still causes the freeze.
Networking=========================================================
An ioctl to delete an ipv6 tunnel leads to a kernel panic http://bugzilla.kernel.org/show_bug.cgi?id=8895 8/16/2007 Summary: The mip6d HA was modified to make a redundancy evolution, when an HA is interrupted, the other takes over, this leads to some creation/deletion of routes and tunnels.
BUG: bad unlock balance detected! http://bugzilla.kernel.org/show_bug.cgi?id=9542 Date: 12/11/2007 Summary: ...bug in the bonding driver...bond->lock should always turn BH off, even on read lock. Handled: Herbert Xu Problem and solution has been identified, but the bug stalled - probably needs someone to submit an actual patch
WIRELESS==========================================================
IWL3945 generates WARNING in mac80211/rx.c code http://bugzilla.kernel.org/show_bug.cgi?id=9656 12/28/2007 WARNING: at net/mac80211/rx.c:1486 __ieee80211_rx() Pid: 0, comm: swapper Not tainted 2.6.24-rc6 #8 Call Trace: <IRQ> [<ffffffff88123d89>] :mac80211:__ieee80211_rx+0xc69/0xd30 [<ffffffff812abd86>] _spin_lock_irqsave+0x26/0xa0 [<ffffffff812ac3a5>] _spin_unlock_irqrestore+0x15/0x30 [<ffffffff8815af91>] :iwl3945:iwl_rx_queue_restock+0xd1/0x160 [<ffffffff812abd86>] _spin_lock_irqsave+0x26/0xa0 [<ffffffff88114f7b>] :mac80211:ieee80211_tasklet_handler+0xbb/0x120 [<ffffffff810420a7>] tasklet_action+0x47/0xb0 [<ffffffff81041fb9>] __do_softirq+0x59/0xd0 [<ffffffff8100d5dc>] call_softirq+0x1c/0x30 [<ffffffff8100f975>] do_softirq+0x35/0x90 [<ffffffff81041ee5>] irq_exit+0x85/0x90 [<ffffffff8100fa54>] do_IRQ+0x84/0x100 [<ffffffff8100c931>] ret_from_intr+0x0/0xa <EOI> [<ffffffff811a312f>] acpi_idle_enter_bm+0x272/0x2de [<ffffffff811a3125>] acpi_idle_enter_bm+0x268/0x2de [<ffffffff81230357>] cpuidle_idle_call+0x97/0xd0 [<ffffffff812302c0>] cpuidle_idle_call+0x0/0xd0 [<ffffffff8100b001>] cpu_idle+0x71/0xe0
NFS/RPC===================================================
in-kernel rpc generates broken RPCBPROC_GETVERSADDR v4 requests http://bugzilla.kernel.org/show_bug.cgi?id=8891 8/15/2007 Problem Description: When locking a file, an invalid RPCBPROC_GETVERSADDR procedure call is sent out Chuck Lever looked at it a while ago
Added linux-scsi for the SCSI ones
On Tue, 2008-02-12 at 00:18 -0800, Natalie Protasevich wrote:
Hello,
The bugs listed are over a month old, and haven't been addressed yet. It would be appreciated if corresponding maintainers identify whether the bugs have been fixed, or need to be worked on, and take appropriate action.
In most cases, reporters are standing by and ready to provide information and necessary testing. Thanks!
SCSI======================================================
Problems on booting http://bugzilla.kernel.org/show_bug.cgi?id=9621 Date: 12/22/2007 Regression Summary: The boot stops / hangs on hardware detection of SCSI. I have an InitioINI-9X00U/UW When I have an usb key sticked in /dev/sba, and run lilo then, then it dont boot but give L99 99 99 99 ... error
I think this was fixed by commit e2d435ea4084022ab88efa74214accb45b1f9e92
Apparently bugzilla email is on the fritz again because this bug report didn't come across linux-scsi.
Resetting RAID attached to a FC Switch causes kernel panic and crash http://bugzilla.kernel.org/show_bug.cgi?id=9598 12/18/2007 Hardware Environment:SunFire X4200 - 2 x dual core AMD Opteron CPUs, 8GB Ram, Qlogic FC adapter. Summary: Resetting the RAID box causes the X4200 to crash.
This one looks like the usual problem of remove re-add with the SCSI device model.
3ware 9650SE -8LPML not recognized by 3w-9xxx driver http://bugzilla.kernel.org/show_bug.cgi?id=8908 08/19/2007 Problem Description: The 3w-9xxx kernel driver for 3ware 9xxx SATA RAID Controller series did not recognize the 3ware 9650SE-8LPML SATA RAID Controller.
Since this one never apparently worked it's not a regression but an enhancement request, isn't it?
However, adding this PCI ID to the driver should be fairly straightforward. Does anyone know what the actual PCI IDs are?
James
On Feb 12, 2008 9:57 AM, James Bottomley James.Bottomley@hansenpartnership.com wrote:
Added linux-scsi for the SCSI ones
On Tue, 2008-02-12 at 00:18 -0800, Natalie Protasevich wrote:
Hello,
The bugs listed are over a month old, and haven't been addressed yet. It would be appreciated if corresponding maintainers identify whether the bugs have been fixed, or need to be worked on, and take appropriate action.
In most cases, reporters are standing by and ready to provide information and necessary testing. Thanks!
SCSI======================================================
Problems on booting http://bugzilla.kernel.org/show_bug.cgi?id=9621 Date: 12/22/2007 Regression Summary: The boot stops / hangs on hardware detection of SCSI. I have an InitioINI-9X00U/UW When I have an usb key sticked in /dev/sba, and run lilo then, then it dont boot but give L99 99 99 99 ... error
I think this was fixed by commit e2d435ea4084022ab88efa74214accb45b1f9e92
Apparently bugzilla email is on the fritz again because this bug report didn't come across linux-scsi.
I just fixed that, thanks. It was incorrect "assign-to" party.
Resetting RAID attached to a FC Switch causes kernel panic and crash http://bugzilla.kernel.org/show_bug.cgi?id=9598 12/18/2007 Hardware Environment:SunFire X4200 - 2 x dual core AMD Opteron CPUs, 8GB Ram, Qlogic FC adapter. Summary: Resetting the RAID box causes the X4200 to crash.
This one looks like the usual problem of remove re-add with the SCSI device model.
3ware 9650SE -8LPML not recognized by 3w-9xxx driver http://bugzilla.kernel.org/show_bug.cgi?id=8908 08/19/2007 Problem Description: The 3w-9xxx kernel driver for 3ware 9xxx SATA RAID Controller series did not recognize the 3ware 9650SE-8LPML SATA RAID Controller.
Since this one never apparently worked it's not a regression but an enhancement request, isn't it?
No this is not a regression. The bug list that I post is just any bugs (mostly unattended or stalled). Sometimes those are regressions off of the Raphael's list, when they don't get resolved for a while, or just random regressions that haven't showed up on the "hot list" by Raphael.
However, adding this PCI ID to the driver should be fairly straightforward. Does anyone know what the actual PCI IDs are?
I just asked the reporter to provide this information, thanks.
James
participants (2)
-
James Bottomley -
Natalie Protasevich