From: Sven Brandau brandau@gmx.de

The TI STA350 is an integrated 2.1-channel power amplifier that is controllable over I2C. This patch adds an ASoC driver for it.

At a glance, this chip is very similar to the STA320 for which a driver already exists. In details, however, the register maps contain subtle differences which made a whole new driver easier to write and maintain.

[daniel@zonque.org: cleanups, DT property rework, rebased on asoc-next] Signed-off-by: Sven Brandau brandau@gmx.de --- I'm sending this patch on behalf of Sven Brandau, who wrote the driver, based on earlier bits for the STA320.

In case of any pending issue, I will amend and resubmit.

Thanks, Daniel

.../devicetree/bindings/sound/st,sta350.txt | 103 ++ include/sound/sta350.h | 52 + sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/sta350.c | 1277 ++++++++++++++++++++ sound/soc/codecs/sta350.h | 228 ++++ 6 files changed, 1666 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/st,sta350.txt create mode 100644 include/sound/sta350.h create mode 100644 sound/soc/codecs/sta350.c create mode 100644 sound/soc/codecs/sta350.h

diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt new file mode 100644 index 0000000..ae0630b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sta350.txt @@ -0,0 +1,103 @@ +STA350 audio CODEC + +The driver for this device only supports I2C. + +Required properties: + + - compatible: "st,sta350" + - reg: the I2C address of the device for I2C + - reset-gpio: a GPIO spec for the reset pin. If specified, it will be + deasserted before communication to the codec starts. + + - power-down-gpio: a GPIO spec for the power down pin. If specified, + it will be deasserted before communication to the codec + starts. + +Optional properties: + + - st,output-conf: number, Selects the output configuration: + 0: 2-channel (full-bridge) power, 2-channel data-out + 1: 2 (half-bridge). 1 (full-bridge) on-board power + 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX + 3: 1 Channel Mono-Parallel + If parameter is missing, mode 0 will be enabled. + + - st,ch1-output-mapping: Channel 1 output mapping + - st,ch2-output-mapping: Channel 2 output mapping + - st,ch3-output-mapping: Channel 3 output mapping + 0: Channel 1 + 1: Channel 2 + 2: Channel 3 + If parameter is missing, channel 1 is choosen. + + - st,thermal-warning-recover: + If present, thermal warning recovery is enabled. + + - st,thermal-warning-adjustment: + If present, thermal warning adjustment is enabled. + + - st,fault-detect-recovery: + If present, then fault recovery will be enabled. + + - st,ffx-power-output-mode: string + The FFX power output mode selects how the FFX output timing is + configured. Must be one of these values: + - "drop-compensation" + - "tapered-compensation" + - "full-power-mode" + - "variable-drop-compensation" (default) + + - st,drop-compensation-ns: number + Only required for "st,ffx-power-output-mode" == + "variable-drop-compensation". + Specifies the drop compensation in nanoseconds. + The value must be in the range of 0..300, and only + multiples of 20 are allowed. Default is 140ns. + + - st,overcurrent-warning-adjustment: + If present, overcurrent warning adjustment is enabled. + + - st,max-power-use-mpcc: + If present, then MPCC bits are used for MPC coefficients, + otherwise standard MPC coefficients are used. + + - st,max-power-corr: + If present, power bridge correction for THD reduction near maximum + power output is enabled. + + - st,am-reduction-mode: + If present, FFX mode runs in AM reduction mode, otherwise normal + FFX mode is used. + + - st,odd-pwm-speed-mode: + If present, PWM speed mode run on odd speed mode (341.3 kHz) on all + channels. If not present, normal PWM spped mode (384 kHz) will be used. + + - st,distortion-compensation: + If present, distortion compensation variable uses DCC coefficient. + If not present, preset DC coefficient is used. + + - st,invalid-input-detect-mute: + If not present, automatic invalid input detect mute is enabled. + + + +Example: + +codec: sta350@38 { + compatible = "st,sta350"; + reg = <0x1c>; + reset-gpio = <&gpio1 19 0>; + power-down-gpio = <&gpio1 16 0>; + st,output-conf = <0x3>; // set output to 2-channel + // (full-bridge) power, + // 2-channel data-out + st,ch1-output-mapping = <0>; // set channel 1 output ch 1 + st,ch2-output-mapping = <0>; // set channel 2 output ch 1 + st,ch3-output-mapping = <0>; // set channel 3 output ch 1 + st,max-power-correction; // enables power bridge + // correction for THD reduction + // near maximum power output + st,invalid-input-detect-mute; // mute if no valid digital + // audio signal is provided. +}; diff --git a/include/sound/sta350.h b/include/sound/sta350.h new file mode 100644 index 0000000..3a329810 --- /dev/null +++ b/include/sound/sta350.h @@ -0,0 +1,52 @@ +/* + * Platform data for ST STA350 ASoC codec driver. + * + * Copyright: 2014 Raumfeld GmbH + * Author: Sven Brandau info@brandau.biz + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef __LINUX_SND__STA350_H +#define __LINUX_SND__STA350_H + +#define STA350_OCFG_2CH 0 +#define STA350_OCFG_2_1CH 1 +#define STA350_OCFG_1CH 3 + +#define STA350_OM_CH1 0 +#define STA350_OM_CH2 1 +#define STA350_OM_CH3 2 + +#define STA350_THERMAL_ADJUSTMENT_ENABLE 1 +#define STA350_THERMAL_RECOVERY_ENABLE 2 +#define STA350_FAULT_DETECT_RECOVERY_BYPASS 1 + +#define STA350_FFX_PM_DROP_COMP 0 +#define STA350_FFX_PM_TAPERED_COMP 1 +#define STA350_FFX_PM_FULL_POWER 2 +#define STA350_FFX_PM_VARIABLE_DROP_COMP 3 + + +struct sta350_platform_data { + u8 output_conf; + u8 ch1_output_mapping; + u8 ch2_output_mapping; + u8 ch3_output_mapping; + u8 ffx_power_output_mode; + u8 drop_compensation_ns; + unsigned int thermal_warning_recovery:1; + unsigned int thermal_warning_adjustment:1; + unsigned int fault_detect_recovery:1; + unsigned int oc_warning_adjustment:1; + unsigned int max_power_use_mpcc:1; + unsigned int max_power_correction:1; + unsigned int am_reduction_mode:1; + unsigned int odd_pwm_speed_mode:1; + unsigned int distortion_compensation:1; + unsigned int invalid_input_detect_mute:1; +}; + +#endif /* __LINUX_SND__STA350_H */ diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index f0e8401..6211889 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -80,6 +80,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_SSM2602_SPI if SPI_MASTER select SND_SOC_SSM2602_I2C if I2C select SND_SOC_STA32X if I2C + select SND_SOC_STA350 if I2C select SND_SOC_STA529 if I2C select SND_SOC_STAC9766 if SND_SOC_AC97_BUS select SND_SOC_TAS5086 if I2C @@ -435,6 +436,9 @@ config SND_SOC_SSM2602_I2C config SND_SOC_STA32X tristate

+config SND_SOC_STA350 + tristate + config SND_SOC_STA529 tristate

diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 3c4d275..efdb4d0 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -74,6 +74,7 @@ snd-soc-ssm2602-objs := ssm2602.o snd-soc-ssm2602-spi-objs := ssm2602-spi.o snd-soc-ssm2602-i2c-objs := ssm2602-i2c.o snd-soc-sta32x-objs := sta32x.o +snd-soc-sta350-objs := sta350.o snd-soc-sta529-objs := sta529.o snd-soc-stac9766-objs := stac9766.o snd-soc-tas5086-objs := tas5086.o @@ -221,6 +222,7 @@ obj-$(CONFIG_SND_SOC_SSM2602) += snd-soc-ssm2602.o obj-$(CONFIG_SND_SOC_SSM2602_SPI) += snd-soc-ssm2602-spi.o obj-$(CONFIG_SND_SOC_SSM2602_I2C) += snd-soc-ssm2602-i2c.o obj-$(CONFIG_SND_SOC_STA32X) += snd-soc-sta32x.o +obj-$(CONFIG_SND_SOC_STA350) += snd-soc-sta350.o obj-$(CONFIG_SND_SOC_STA529) += snd-soc-sta529.o obj-$(CONFIG_SND_SOC_STAC9766) += snd-soc-stac9766.o obj-$(CONFIG_SND_SOC_TAS5086) += snd-soc-tas5086.o diff --git a/sound/soc/codecs/sta350.c b/sound/soc/codecs/sta350.c new file mode 100644 index 0000000..c78d1c5 --- /dev/null +++ b/sound/soc/codecs/sta350.c @@ -0,0 +1,1277 @@ +/* + * Codec driver for ST STA350 2.1-channel high-efficiency digital audio system + * + * Copyright: 2014 Raumfeld GmbH + * Author: Sven Brandau info@brandau.biz + * + * based on code from: + * Raumfeld GmbH + * Johannes Stezenbach js@sig21.net + * Wolfson Microelectronics PLC. + * Mark Brown broonie@opensource.wolfsonmicro.com + * Freescale Semiconductor, Inc. + * Timur Tabi timur@freescale.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ":%s:%d: " fmt, __func__, __LINE__ + +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/pm.h> +#include <linux/i2c.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/soc-dapm.h> +#include <sound/initval.h> +#include <sound/tlv.h> + +#include <sound/sta350.h> +#include "sta350.h" + +#define STA350_RATES (SNDRV_PCM_RATE_32000 | \ + SNDRV_PCM_RATE_44100 | \ + SNDRV_PCM_RATE_48000 | \ + SNDRV_PCM_RATE_88200 | \ + SNDRV_PCM_RATE_96000 | \ + SNDRV_PCM_RATE_176400 | \ + SNDRV_PCM_RATE_192000) + +#define STA350_FORMATS \ + (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S16_BE | \ + SNDRV_PCM_FMTBIT_S18_3LE | SNDRV_PCM_FMTBIT_S18_3BE | \ + SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S20_3BE | \ + SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_3BE | \ + SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S24_BE | \ + SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_S32_BE) + +/* Power-up register defaults */ +static const struct reg_default sta350_regs[] = { + { 0x0, 0x63 }, + { 0x1, 0x80 }, + { 0x2, 0xdf }, + { 0x3, 0x40 }, + { 0x4, 0xc2 }, + { 0x5, 0x5c }, + { 0x6, 0x00 }, + { 0x7, 0xff }, + { 0x8, 0x60 }, + { 0x9, 0x60 }, + { 0xa, 0x60 }, + { 0xb, 0x00 }, + { 0xc, 0x00 }, + { 0xd, 0x00 }, + { 0xe, 0x00 }, + { 0xf, 0x40 }, + { 0x10, 0x80 }, + { 0x11, 0x77 }, + { 0x12, 0x6a }, + { 0x13, 0x69 }, + { 0x14, 0x6a }, + { 0x15, 0x69 }, + { 0x16, 0x00 }, + { 0x17, 0x00 }, + { 0x18, 0x00 }, + { 0x19, 0x00 }, + { 0x1a, 0x00 }, + { 0x1b, 0x00 }, + { 0x1c, 0x00 }, + { 0x1d, 0x00 }, + { 0x1e, 0x00 }, + { 0x1f, 0x00 }, + { 0x20, 0x00 }, + { 0x21, 0x00 }, + { 0x22, 0x00 }, + { 0x23, 0x00 }, + { 0x24, 0x00 }, + { 0x25, 0x00 }, + { 0x26, 0x00 }, + { 0x27, 0x2a }, + { 0x28, 0xc0 }, + { 0x29, 0xf3 }, + { 0x2a, 0x33 }, + { 0x2b, 0x00 }, + { 0x2c, 0x0c }, + { 0x31, 0x00 }, + { 0x36, 0x00 }, + { 0x37, 0x00 }, + { 0x38, 0x00 }, + { 0x39, 0x01 }, + { 0x3a, 0xee }, + { 0x3b, 0xff }, + { 0x3c, 0x7e }, + { 0x3d, 0xc0 }, + { 0x3e, 0x26 }, + { 0x3f, 0x00 }, + { 0x48, 0x00 }, + { 0x49, 0x00 }, + { 0x4a, 0x00 }, + { 0x4b, 0x04 }, + { 0x4c, 0x00 }, +}; + +static const struct regmap_range sta350_write_regs_range[] = { + regmap_reg_range(STA350_CONFA, STA350_AUTO2), + regmap_reg_range(STA350_C1CFG, STA350_FDRC2), + regmap_reg_range(STA350_EQCFG, STA350_EVOLRES), + regmap_reg_range(STA350_NSHAPE, STA350_MISC2), +}; + +static const struct regmap_range sta350_read_regs_range[] = { + regmap_reg_range(STA350_CONFA, STA350_AUTO2), + regmap_reg_range(STA350_C1CFG, STA350_STATUS), + regmap_reg_range(STA350_EQCFG, STA350_EVOLRES), + regmap_reg_range(STA350_NSHAPE, STA350_MISC2), +}; + +static const struct regmap_range sta350_volatile_regs_range[] = { + regmap_reg_range(STA350_CFADDR2, STA350_CFUD), + regmap_reg_range(STA350_STATUS, STA350_STATUS), +}; + +static const struct regmap_access_table sta350_write_regs = { + .yes_ranges = sta350_write_regs_range, + .n_yes_ranges = ARRAY_SIZE(sta350_write_regs_range), +}; + +static const struct regmap_access_table sta350_read_regs = { + .yes_ranges = sta350_read_regs_range, + .n_yes_ranges = ARRAY_SIZE(sta350_read_regs_range), +}; + +static const struct regmap_access_table sta350_volatile_regs = { + .yes_ranges = sta350_volatile_regs_range, + .n_yes_ranges = ARRAY_SIZE(sta350_volatile_regs_range), +}; + +/* regulator power supply names */ +static const char const *sta350_supply_names[] = { + "vdd-dig", /* digital supply, 3.3V */ + "vdd-pll", /* pll supply, 3.3V */ + "vcc" /* power amp supply, 5V - 26V */ +}; + +/* codec private data */ +struct sta350_priv { + struct regmap *regmap; + struct regulator_bulk_data supplies[ARRAY_SIZE(sta350_supply_names)]; + struct sta350_platform_data *pdata; + + unsigned int mclk; + unsigned int format; + + u32 coef_shadow[STA350_COEF_COUNT]; + int shutdown; + int gpio_nreset; + int gpio_power_down; +}; + +static const DECLARE_TLV_DB_SCALE(mvol_tlv, -12750, 50, 1); +static const DECLARE_TLV_DB_SCALE(chvol_tlv, -7950, 50, 1); +static const DECLARE_TLV_DB_SCALE(tone_tlv, -1200, 200, 0); + +static const char const *sta350_drc_ac[] = { + "Anti-Clipping", "Dynamic Range Compression" +}; +static const char const *sta350_auto_gc_mode[] = { + "User", "AC no clipping", "AC limited clipping (10%)", + "DRC nighttime listening mode" +}; +static const char const *sta350_auto_xo_mode[] = { + "User", "80Hz", "100Hz", "120Hz", "140Hz", "160Hz", "180Hz", + "200Hz", "220Hz", "240Hz", "260Hz", "280Hz", "300Hz", "320Hz", + "340Hz", "360Hz" +}; +static const char const *sta350_binary_output[] = { + "FFX 3-state output - normal operation", "Binary output" +}; +static const char const *sta350_limiter_select[] = { + "Limiter Disabled", "Limiter #1", "Limiter #2" +}; +static const char const *sta350_limiter_attack_rate[] = { + "3.1584", "2.7072", "2.2560", "1.8048", "1.3536", "0.9024", + "0.4512", "0.2256", "0.1504", "0.1123", "0.0902", "0.0752", + "0.0645", "0.0564", "0.0501", "0.0451" +}; +static const char const *sta350_limiter_release_rate[] = { + "0.5116", "0.1370", "0.0744", "0.0499", "0.0360", "0.0299", + "0.0264", "0.0208", "0.0198", "0.0172", "0.0147", "0.0137", + "0.0134", "0.0117", "0.0110", "0.0104" +}; +static const char const *sta350_noise_shaper_type[] = { + "Third order", "Forth order" +}; + +static const unsigned int sta350_limiter_ac_attack_tlv[] = { + TLV_DB_RANGE_HEAD(2), + 0, 7, TLV_DB_SCALE_ITEM(-1200, 200, 0), + 8, 16, TLV_DB_SCALE_ITEM(300, 100, 0), +}; + +static const unsigned int sta350_limiter_ac_release_tlv[] = { + TLV_DB_RANGE_HEAD(5), + 0, 0, TLV_DB_SCALE_ITEM(TLV_DB_GAIN_MUTE, 0, 0), + 1, 1, TLV_DB_SCALE_ITEM(-2900, 0, 0), + 2, 2, TLV_DB_SCALE_ITEM(-2000, 0, 0), + 3, 8, TLV_DB_SCALE_ITEM(-1400, 200, 0), + 8, 16, TLV_DB_SCALE_ITEM(-700, 100, 0), +}; + +static const unsigned int sta350_limiter_drc_attack_tlv[] = { + TLV_DB_RANGE_HEAD(3), + 0, 7, TLV_DB_SCALE_ITEM(-3100, 200, 0), + 8, 13, TLV_DB_SCALE_ITEM(-1600, 100, 0), + 14, 16, TLV_DB_SCALE_ITEM(-1000, 300, 0), +}; + +static const unsigned int sta350_limiter_drc_release_tlv[] = { + TLV_DB_RANGE_HEAD(5), + 0, 0, TLV_DB_SCALE_ITEM(TLV_DB_GAIN_MUTE, 0, 0), + 1, 2, TLV_DB_SCALE_ITEM(-3800, 200, 0), + 3, 4, TLV_DB_SCALE_ITEM(-3300, 200, 0), + 5, 12, TLV_DB_SCALE_ITEM(-3000, 200, 0), + 13, 16, TLV_DB_SCALE_ITEM(-1500, 300, 0), +}; + +static const struct soc_enum sta350_drc_ac_enum = + SOC_ENUM_SINGLE(STA350_CONFD, STA350_CONFD_DRC_SHIFT, + 2, sta350_drc_ac); +static const struct soc_enum sta350_noise_shaper_enum = + SOC_ENUM_SINGLE(STA350_CONFE, STA350_CONFE_NSBW_SHIFT, + 2, sta350_noise_shaper_type); +static const struct soc_enum sta350_auto_gc_enum = + SOC_ENUM_SINGLE(STA350_AUTO1, STA350_AUTO1_AMGC_SHIFT, + 4, sta350_auto_gc_mode); +static const struct soc_enum sta350_auto_xo_enum = + SOC_ENUM_SINGLE(STA350_AUTO2, STA350_AUTO2_XO_SHIFT, + 16, sta350_auto_xo_mode); +static const struct soc_enum sta350_binary_output_ch1_enum = + SOC_ENUM_SINGLE(STA350_C1CFG, STA350_CxCFG_BO_SHIFT, + 2, sta350_binary_output); +static const struct soc_enum sta350_binary_output_ch2_enum = + SOC_ENUM_SINGLE(STA350_C2CFG, STA350_CxCFG_BO_SHIFT, + 2, sta350_binary_output); +static const struct soc_enum sta350_binary_output_ch3_enum = + SOC_ENUM_SINGLE(STA350_C3CFG, STA350_CxCFG_BO_SHIFT, + 2, sta350_binary_output); +static const struct soc_enum sta350_limiter_ch1_enum = + SOC_ENUM_SINGLE(STA350_C1CFG, STA350_CxCFG_LS_SHIFT, + 3, sta350_limiter_select); +static const struct soc_enum sta350_limiter_ch2_enum = + SOC_ENUM_SINGLE(STA350_C2CFG, STA350_CxCFG_LS_SHIFT, + 3, sta350_limiter_select); +static const struct soc_enum sta350_limiter_ch3_enum = + SOC_ENUM_SINGLE(STA350_C3CFG, STA350_CxCFG_LS_SHIFT, + 3, sta350_limiter_select); +static const struct soc_enum sta350_limiter1_attack_rate_enum = + SOC_ENUM_SINGLE(STA350_L1AR, STA350_LxA_SHIFT, + 16, sta350_limiter_attack_rate); +static const struct soc_enum sta350_limiter2_attack_rate_enum = + SOC_ENUM_SINGLE(STA350_L2AR, STA350_LxA_SHIFT, + 16, sta350_limiter_attack_rate); +static const struct soc_enum sta350_limiter1_release_rate_enum = + SOC_ENUM_SINGLE(STA350_L1AR, STA350_LxR_SHIFT, + 16, sta350_limiter_release_rate); +static const struct soc_enum sta350_limiter2_release_rate_enum = + SOC_ENUM_SINGLE(STA350_L2AR, STA350_LxR_SHIFT, + 16, sta350_limiter_release_rate); + +/* + * byte array controls for setting biquad, mixer, scaling coefficients; + * for biquads all five coefficients need to be set in one go, + * mixer and pre/postscale coefs can be set individually; + * each coef is 24bit, the bytes are ordered in the same way + * as given in the STA350 data sheet (big endian; b1, b2, a1, a2, b0) + */ + +static int sta350_coefficient_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + int numcoef = kcontrol->private_value >> 16; + uinfo->type = SNDRV_CTL_ELEM_TYPE_BYTES; + uinfo->count = 3 * numcoef; + return 0; +} + +static int sta350_coefficient_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + int numcoef = kcontrol->private_value >> 16; + int index = kcontrol->private_value & 0xffff; + unsigned int cfud, val; + int i; + + /* preserve reserved bits in STA350_CFUD */ + regmap_read(sta350->regmap, STA350_CFUD, &cfud); + cfud &= 0xf0; + /* + * chip documentation does not say if the bits are self clearing, + * so do it explicitly + */ + regmap_write(sta350->regmap, STA350_CFUD, cfud); + + regmap_write(sta350->regmap, STA350_CFADDR2, index); + if (numcoef == 1) + regmap_write(sta350->regmap, STA350_CFUD, cfud | 0x04); + else if (numcoef == 5) + regmap_write(sta350->regmap, STA350_CFUD, cfud | 0x08); + else + return -EINVAL; + + for (i = 0; i < 3 * numcoef; i++) { + regmap_read(sta350->regmap, STA350_B1CF1 + i, &val); + ucontrol->value.bytes.data[i] = val; + } + + return 0; +} + +static int sta350_coefficient_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + int numcoef = kcontrol->private_value >> 16; + int index = kcontrol->private_value & 0xffff; + unsigned int cfud; + int i; + + /* preserve reserved bits in STA350_CFUD */ + regmap_read(sta350->regmap, STA350_CFUD, &cfud); + cfud &= 0xf0; + /* + * chip documentation does not say if the bits are self clearing, + * so do it explicitly + */ + regmap_write(sta350->regmap, STA350_CFUD, cfud); + + regmap_write(sta350->regmap, STA350_CFADDR2, index); + for (i = 0; i < numcoef && (index + i < STA350_COEF_COUNT); i++) + sta350->coef_shadow[index + i] = + (ucontrol->value.bytes.data[3 * i] << 16) + | (ucontrol->value.bytes.data[3 * i + 1] << 8) + | (ucontrol->value.bytes.data[3 * i + 2]); + for (i = 0; i < 3 * numcoef; i++) + regmap_write(sta350->regmap, STA350_B1CF1 + i, + ucontrol->value.bytes.data[i]); + if (numcoef == 1) + regmap_write(sta350->regmap, STA350_CFUD, cfud | 0x01); + else if (numcoef == 5) + regmap_write(sta350->regmap, STA350_CFUD, cfud | 0x02); + else + return -EINVAL; + + return 0; +} + +static int sta350_sync_coef_shadow(struct snd_soc_codec *codec) +{ + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + unsigned int cfud; + int i; + + /* preserve reserved bits in STA350_CFUD */ + regmap_read(sta350->regmap, STA350_CFUD, &cfud); + cfud &= 0xf0; + + for (i = 0; i < STA350_COEF_COUNT; i++) { + regmap_write(sta350->regmap, STA350_CFADDR2, i); + regmap_write(sta350->regmap, STA350_B1CF1, + (sta350->coef_shadow[i] >> 16) & 0xff); + regmap_write(sta350->regmap, STA350_B1CF2, + (sta350->coef_shadow[i] >> 8) & 0xff); + regmap_write(sta350->regmap, STA350_B1CF3, + (sta350->coef_shadow[i]) & 0xff); + /* + * chip documentation does not say if the bits are + * self-clearing, so do it explicitly + */ + regmap_write(sta350->regmap, STA350_CFUD, cfud); + regmap_write(sta350->regmap, STA350_CFUD, cfud | 0x01); + } + return 0; +} + +static int sta350_cache_sync(struct snd_soc_codec *codec) +{ + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + unsigned int mute; + int rc; + + /* mute during register sync */ + regmap_read(sta350->regmap, STA350_CFUD, &mute); + regmap_write(sta350->regmap, STA350_MMUTE, mute | STA350_MMUTE_MMUTE); + sta350_sync_coef_shadow(codec); + rc = regcache_sync(sta350->regmap); + regmap_write(sta350->regmap, STA350_MMUTE, mute); + return rc; +} + +#define SINGLE_COEF(xname, index) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, \ + .info = sta350_coefficient_info, \ + .get = sta350_coefficient_get,\ + .put = sta350_coefficient_put, \ + .private_value = index | (1 << 16) } + +#define BIQUAD_COEFS(xname, index) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, \ + .info = sta350_coefficient_info, \ + .get = sta350_coefficient_get,\ + .put = sta350_coefficient_put, \ + .private_value = index | (5 << 16) } + +static const struct snd_kcontrol_new sta350_snd_controls[] = { +SOC_SINGLE_TLV("Master Volume", STA350_MVOL, 0, 0xff, 1, mvol_tlv), +/* VOL */ +SOC_SINGLE_TLV("Ch1 Volume", STA350_C1VOL, 0, 0xff, 1, chvol_tlv), +SOC_SINGLE_TLV("Ch2 Volume", STA350_C2VOL, 0, 0xff, 1, chvol_tlv), +SOC_SINGLE_TLV("Ch3 Volume", STA350_C3VOL, 0, 0xff, 1, chvol_tlv), +/* CONFD */ +SOC_SINGLE("High Pass Filter Bypass Switch", + STA350_CONFD, STA350_CONFD_HPB_SHIFT, 1, 1), +SOC_SINGLE("De-emphasis Filter Switch", + STA350_CONFD, STA350_CONFD_DEMP_SHIFT, 1, 0), +SOC_SINGLE("DSP Bypass Switch", + STA350_CONFD, STA350_CONFD_DSPB_SHIFT, 1, 0), +SOC_SINGLE("Post-scale Link Switch", + STA350_CONFD, STA350_CONFD_PSL_SHIFT, 1, 0), +SOC_SINGLE("Biquad Coefficient Link Switch", + STA350_CONFD, STA350_CONFD_BQL_SHIFT, 1, 0), +SOC_ENUM("Compressor/Limiter Switch", sta350_drc_ac_enum), +SOC_ENUM("Noise Shaper Bandwidth", sta350_noise_shaper_enum), +SOC_SINGLE("Zero-detect Mute Enable Switch", + STA350_CONFD, STA350_CONFD_ZDE_SHIFT, 1, 0), +SOC_SINGLE("Submix Mode Switch", + STA350_CONFD, STA350_CONFD_SME_SHIFT, 1, 0), +/* CONFE */ +SOC_SINGLE("Zero Cross Switch", STA350_CONFE, STA350_CONFE_ZCE_SHIFT, 1, 0), +SOC_SINGLE("Soft Ramp Switch", STA350_CONFE, STA350_CONFE_SVE_SHIFT, 1, 0), +/* MUTE */ +SOC_SINGLE("Master Switch", STA350_MMUTE, STA350_MMUTE_MMUTE_SHIFT, 1, 1), +SOC_SINGLE("Ch1 Switch", STA350_MMUTE, STA350_MMUTE_C1M_SHIFT, 1, 1), +SOC_SINGLE("Ch2 Switch", STA350_MMUTE, STA350_MMUTE_C2M_SHIFT, 1, 1), +SOC_SINGLE("Ch3 Switch", STA350_MMUTE, STA350_MMUTE_C3M_SHIFT, 1, 1), +/* AUTOx */ +SOC_ENUM("Automode GC", sta350_auto_gc_enum), +SOC_ENUM("Automode XO", sta350_auto_xo_enum), +/* CxCFG */ +SOC_SINGLE("Ch1 Tone Control Bypass Switch", + STA350_C1CFG, STA350_CxCFG_TCB_SHIFT, 1, 0), +SOC_SINGLE("Ch2 Tone Control Bypass Switch", + STA350_C2CFG, STA350_CxCFG_TCB_SHIFT, 1, 0), +SOC_SINGLE("Ch1 EQ Bypass Switch", + STA350_C1CFG, STA350_CxCFG_EQBP_SHIFT, 1, 0), +SOC_SINGLE("Ch2 EQ Bypass Switch", + STA350_C2CFG, STA350_CxCFG_EQBP_SHIFT, 1, 0), +SOC_SINGLE("Ch1 Master Volume Bypass Switch", + STA350_C1CFG, STA350_CxCFG_VBP_SHIFT, 1, 0), +SOC_SINGLE("Ch2 Master Volume Bypass Switch", + STA350_C1CFG, STA350_CxCFG_VBP_SHIFT, 1, 0), +SOC_SINGLE("Ch3 Master Volume Bypass Switch", + STA350_C1CFG, STA350_CxCFG_VBP_SHIFT, 1, 0), +SOC_ENUM("Ch1 Binary Output Select", sta350_binary_output_ch1_enum), +SOC_ENUM("Ch2 Binary Output Select", sta350_binary_output_ch2_enum), +SOC_ENUM("Ch3 Binary Output Select", sta350_binary_output_ch3_enum), +SOC_ENUM("Ch1 Limiter Select", sta350_limiter_ch1_enum), +SOC_ENUM("Ch2 Limiter Select", sta350_limiter_ch2_enum), +SOC_ENUM("Ch3 Limiter Select", sta350_limiter_ch3_enum), +/* TONE */ +SOC_SINGLE_RANGE_TLV("Bass Tone Control Volume", + STA350_TONE, STA350_TONE_BTC_SHIFT, 1, 13, 0, tone_tlv), +SOC_SINGLE_RANGE_TLV("Treble Tone Control Volume", + STA350_TONE, STA350_TONE_TTC_SHIFT, 1, 13, 0, tone_tlv), +SOC_ENUM("Limiter1 Attack Rate (dB/ms)", sta350_limiter1_attack_rate_enum), +SOC_ENUM("Limiter2 Attack Rate (dB/ms)", sta350_limiter2_attack_rate_enum), +SOC_ENUM("Limiter1 Release Rate (dB/ms)", sta350_limiter1_release_rate_enum), +SOC_ENUM("Limiter2 Release Rate (dB/ms)", sta350_limiter2_release_rate_enum), + +/* + * depending on mode, the attack/release thresholds have + * two different enum definitions; provide both + */ +SOC_SINGLE_TLV("Limiter1 Attack Threshold (AC Mode)", + STA350_L1ATRT, STA350_LxA_SHIFT, + 16, 0, sta350_limiter_ac_attack_tlv), +SOC_SINGLE_TLV("Limiter2 Attack Threshold (AC Mode)", + STA350_L2ATRT, STA350_LxA_SHIFT, + 16, 0, sta350_limiter_ac_attack_tlv), +SOC_SINGLE_TLV("Limiter1 Release Threshold (AC Mode)", + STA350_L1ATRT, STA350_LxR_SHIFT, + 16, 0, sta350_limiter_ac_release_tlv), +SOC_SINGLE_TLV("Limiter2 Release Threshold (AC Mode)", + STA350_L2ATRT, STA350_LxR_SHIFT, + 16, 0, sta350_limiter_ac_release_tlv), +SOC_SINGLE_TLV("Limiter1 Attack Threshold (DRC Mode)", + STA350_L1ATRT, STA350_LxA_SHIFT, + 16, 0, sta350_limiter_drc_attack_tlv), +SOC_SINGLE_TLV("Limiter2 Attack Threshold (DRC Mode)", + STA350_L2ATRT, STA350_LxA_SHIFT, + 16, 0, sta350_limiter_drc_attack_tlv), +SOC_SINGLE_TLV("Limiter1 Release Threshold (DRC Mode)", + STA350_L1ATRT, STA350_LxR_SHIFT, + 16, 0, sta350_limiter_drc_release_tlv), +SOC_SINGLE_TLV("Limiter2 Release Threshold (DRC Mode)", + STA350_L2ATRT, STA350_LxR_SHIFT, + 16, 0, sta350_limiter_drc_release_tlv), + +BIQUAD_COEFS("Ch1 - Biquad 1", 0), +BIQUAD_COEFS("Ch1 - Biquad 2", 5), +BIQUAD_COEFS("Ch1 - Biquad 3", 10), +BIQUAD_COEFS("Ch1 - Biquad 4", 15), +BIQUAD_COEFS("Ch2 - Biquad 1", 20), +BIQUAD_COEFS("Ch2 - Biquad 2", 25), +BIQUAD_COEFS("Ch2 - Biquad 3", 30), +BIQUAD_COEFS("Ch2 - Biquad 4", 35), +BIQUAD_COEFS("High-pass", 40), +BIQUAD_COEFS("Low-pass", 45), +SINGLE_COEF("Ch1 - Prescale", 50), +SINGLE_COEF("Ch2 - Prescale", 51), +SINGLE_COEF("Ch1 - Postscale", 52), +SINGLE_COEF("Ch2 - Postscale", 53), +SINGLE_COEF("Ch3 - Postscale", 54), +SINGLE_COEF("Thermal warning - Postscale", 55), +SINGLE_COEF("Ch1 - Mix 1", 56), +SINGLE_COEF("Ch1 - Mix 2", 57), +SINGLE_COEF("Ch2 - Mix 1", 58), +SINGLE_COEF("Ch2 - Mix 2", 59), +SINGLE_COEF("Ch3 - Mix 1", 60), +SINGLE_COEF("Ch3 - Mix 2", 61), +}; + +static const struct snd_soc_dapm_widget sta350_dapm_widgets[] = { +SND_SOC_DAPM_DAC("DAC", "Playback", SND_SOC_NOPM, 0, 0), +SND_SOC_DAPM_OUTPUT("LEFT"), +SND_SOC_DAPM_OUTPUT("RIGHT"), +SND_SOC_DAPM_OUTPUT("SUB"), +}; + +static const struct snd_soc_dapm_route sta350_dapm_routes[] = { + { "LEFT", NULL, "DAC" }, + { "RIGHT", NULL, "DAC" }, + { "SUB", NULL, "DAC" }, +}; + +/* MCLK interpolation ratio per fs */ +static struct { + int fs; + int ir; +} interpolation_ratios[] = { + { 32000, 0 }, + { 44100, 0 }, + { 48000, 0 }, + { 88200, 1 }, + { 96000, 1 }, + { 176400, 2 }, + { 192000, 2 }, +}; + +/* MCLK to fs clock ratios */ +static int mcs_ratio_table[3][6] = { + { 768, 512, 384, 256, 128, 576 }, + { 384, 256, 192, 128, 64, 0 }, + { 192, 128, 96, 64, 32, 0 }, +}; + +/** + * sta350_set_dai_sysclk - configure MCLK + * @codec_dai: the codec DAI + * @clk_id: the clock ID (ignored) + * @freq: the MCLK input frequency + * @dir: the clock direction (ignored) + * + * The value of MCLK is used to determine which sample rates are supported + * by the STA350, based on the mcs_ratio_table. + * + * This function must be called by the machine driver's 'startup' function, + * otherwise the list of supported sample rates will not be available in + * time for ALSA. + */ +static int sta350_set_dai_sysclk(struct snd_soc_dai *codec_dai, + int clk_id, unsigned int freq, int dir) +{ + struct snd_soc_codec *codec = codec_dai->codec; + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + + pr_debug("mclk=%u\n", freq); + sta350->mclk = freq; + + return 0; +} + +/** + * sta350_set_dai_fmt - configure the codec for the selected audio format + * @codec_dai: the codec DAI + * @fmt: a SND_SOC_DAIFMT_x value indicating the data format + * + * This function takes a bitmask of SND_SOC_DAIFMT_x bits and programs the + * codec accordingly. + */ +static int sta350_set_dai_fmt(struct snd_soc_dai *codec_dai, + unsigned int fmt) +{ + struct snd_soc_codec *codec = codec_dai->codec; + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + unsigned int confb; + + regmap_read(sta350->regmap, STA350_CONFB, &confb); + + pr_debug("\n"); + confb &= ~(STA350_CONFB_C1IM | STA350_CONFB_C2IM); + + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBS_CFS: + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { + case SND_SOC_DAIFMT_I2S: + case SND_SOC_DAIFMT_RIGHT_J: + case SND_SOC_DAIFMT_LEFT_J: + sta350->format = fmt & SND_SOC_DAIFMT_FORMAT_MASK; + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_INV_MASK) { + case SND_SOC_DAIFMT_NB_NF: + confb |= STA350_CONFB_C2IM; + break; + case SND_SOC_DAIFMT_NB_IF: + confb |= STA350_CONFB_C1IM; + break; + default: + return -EINVAL; + } + + regmap_write(sta350->regmap, STA350_CONFB, confb); + return 0; +} + +/** + * sta350_hw_params - program the STA350 with the given hardware parameters. + * @substream: the audio stream + * @params: the hardware parameters to set + * @dai: the SOC DAI (ignored) + * + * This function programs the hardware with the values provided. + * Specifically, the sample rate and the data format. + */ +static int sta350_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_codec *codec = dai->codec; + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + int i, mcs = -EINVAL, ir = -EINVAL; + unsigned int confa, confb; + unsigned int rate, ratio; + + if (!sta350->mclk) { + dev_err(codec->dev, + "sta350->mclk is unset. Unable to determine ratio\n"); + return -EIO; + } + + rate = params_rate(params); + ratio = sta350->mclk / rate; + pr_debug("rate: %u, ratio: %u\n", rate, ratio); + + for (i = 0; i < ARRAY_SIZE(interpolation_ratios); i++) + if (interpolation_ratios[i].fs == rate) { + ir = interpolation_ratios[i].ir; + break; + } + if (ir < 0) { + dev_err(codec->dev, "Unsupported samplerate: %u\n", rate); + return -EINVAL; + } + + for (i = 0; i < 6; i++) + if (mcs_ratio_table[ir][i] == ratio) { + mcs = i; + break; + } + if (mcs < 0) { + dev_err(codec->dev, "Unresolvable ratio: %u\n", ratio); + return -EINVAL; + } + + regmap_read(sta350->regmap, STA350_CONFA, &confa); + confa &= ~(STA350_CONFA_MCS_MASK | STA350_CONFA_IR_MASK); + confa |= (ir << STA350_CONFA_IR_SHIFT) | + (mcs << STA350_CONFA_MCS_SHIFT); + + regmap_read(sta350->regmap, STA350_CONFB, &confb); + confb &= ~(STA350_CONFB_SAI_MASK | STA350_CONFB_SAIFB); + switch (params_format(params)) { + case SNDRV_PCM_FORMAT_S24_LE: + case SNDRV_PCM_FORMAT_S24_BE: + case SNDRV_PCM_FORMAT_S24_3LE: + case SNDRV_PCM_FORMAT_S24_3BE: + pr_debug("24bit\n"); + /* fall through */ + case SNDRV_PCM_FORMAT_S32_LE: + case SNDRV_PCM_FORMAT_S32_BE: + pr_debug("24bit or 32bit\n"); + switch (sta350->format) { + case SND_SOC_DAIFMT_I2S: + confb |= 0x0; + break; + case SND_SOC_DAIFMT_LEFT_J: + confb |= 0x1; + break; + case SND_SOC_DAIFMT_RIGHT_J: + confb |= 0x2; + break; + } + + break; + case SNDRV_PCM_FORMAT_S20_3LE: + case SNDRV_PCM_FORMAT_S20_3BE: + pr_debug("20bit\n"); + switch (sta350->format) { + case SND_SOC_DAIFMT_I2S: + confb |= 0x4; + break; + case SND_SOC_DAIFMT_LEFT_J: + confb |= 0x5; + break; + case SND_SOC_DAIFMT_RIGHT_J: + confb |= 0x6; + break; + } + + break; + case SNDRV_PCM_FORMAT_S18_3LE: + case SNDRV_PCM_FORMAT_S18_3BE: + pr_debug("18bit\n"); + switch (sta350->format) { + case SND_SOC_DAIFMT_I2S: + confb |= 0x8; + break; + case SND_SOC_DAIFMT_LEFT_J: + confb |= 0x9; + break; + case SND_SOC_DAIFMT_RIGHT_J: + confb |= 0xa; + break; + } + + break; + case SNDRV_PCM_FORMAT_S16_LE: + case SNDRV_PCM_FORMAT_S16_BE: + pr_debug("16bit\n"); + switch (sta350->format) { + case SND_SOC_DAIFMT_I2S: + confb |= 0x0; + break; + case SND_SOC_DAIFMT_LEFT_J: + confb |= 0xd; + break; + case SND_SOC_DAIFMT_RIGHT_J: + confb |= 0xe; + break; + } + + break; + default: + return -EINVAL; + } + + regmap_write(sta350->regmap, STA350_CONFA, confa); + regmap_write(sta350->regmap, STA350_CONFB, confb); + return 0; +} + +static int sta350_startup_sequence(struct sta350_priv *sta350) +{ + if (gpio_is_valid(sta350->gpio_power_down)) + gpio_set_value(sta350->gpio_power_down, 1); + + if (gpio_is_valid(sta350->gpio_nreset)) { + gpio_set_value(sta350->gpio_nreset, 1); + mdelay(1); + gpio_set_value(sta350->gpio_nreset, 0); + mdelay(1); + gpio_set_value(sta350->gpio_nreset, 1); + mdelay(1); + } + + return 0; +} + +/** + * sta350_set_bias_level - DAPM callback + * @codec: the codec device + * @level: DAPM power level + * + * This is called by ALSA to put the codec into low power mode + * or to wake it up. If the codec is powered off completely + * all registers must be restored after power on. + */ +static int sta350_set_bias_level(struct snd_soc_codec *codec, + enum snd_soc_bias_level level) +{ + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + int ret; + + pr_debug("level = %d\n", level); + switch (level) { + case SND_SOC_BIAS_ON: + break; + + case SND_SOC_BIAS_PREPARE: + /* Full power on */ + regmap_update_bits(sta350->regmap, STA350_CONFF, + STA350_CONFF_PWDN | STA350_CONFF_EAPD, + STA350_CONFF_PWDN | STA350_CONFF_EAPD); + break; + + case SND_SOC_BIAS_STANDBY: + if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) { + ret = regulator_bulk_enable( + ARRAY_SIZE(sta350->supplies), + sta350->supplies); + if (ret < 0) { + dev_err(codec->dev, + "Failed to enable supplies: %d\n", + ret); + return ret; + } + sta350_startup_sequence(sta350); + sta350_cache_sync(codec); + } + + /* Power down */ + regmap_update_bits(sta350->regmap, STA350_CONFF, + STA350_CONFF_PWDN | STA350_CONFF_EAPD, + 0); + + break; + + case SND_SOC_BIAS_OFF: + /* The chip runs through the power down sequence for us. */ + regmap_update_bits(sta350->regmap, STA350_CONFF, + STA350_CONFF_PWDN | STA350_CONFF_EAPD, 0); + /* power down: low */ + if (gpio_is_valid(sta350->gpio_power_down)) + gpio_set_value(sta350->gpio_power_down, 0); + + regulator_bulk_disable(ARRAY_SIZE(sta350->supplies), + sta350->supplies); + break; + } + codec->dapm.bias_level = level; + return 0; +} + +static const struct snd_soc_dai_ops sta350_dai_ops = { + .hw_params = sta350_hw_params, + .set_sysclk = sta350_set_dai_sysclk, + .set_fmt = sta350_set_dai_fmt, +}; + +static struct snd_soc_dai_driver sta350_dai = { + .name = "sta350-hifi", + .playback = { + .stream_name = "Playback", + .channels_min = 2, + .channels_max = 2, + .rates = STA350_RATES, + .formats = STA350_FORMATS, + }, + .ops = &sta350_dai_ops, +}; + +#ifdef CONFIG_PM +static int sta350_suspend(struct snd_soc_codec *codec) +{ + sta350_set_bias_level(codec, SND_SOC_BIAS_OFF); + return 0; +} + +static int sta350_resume(struct snd_soc_codec *codec) +{ + sta350_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + return 0; +} +#else +#define sta350_suspend NULL +#define sta350_resume NULL +#endif + +static int sta350_probe(struct snd_soc_codec *codec) +{ + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + struct sta350_platform_data *pdata = sta350->pdata; + int i, ret = 0, thermal = 0; + + if (gpio_is_valid(sta350->gpio_nreset)) + if (devm_gpio_request_one(codec->dev, sta350->gpio_nreset, + GPIOF_OUT_INIT_HIGH, + "ST350 Reset")) + sta350->gpio_nreset = -EINVAL; + + if (gpio_is_valid(sta350->gpio_power_down)) + if (devm_gpio_request_one(codec->dev, sta350->gpio_power_down, + GPIOF_OUT_INIT_HIGH, + "ST350 Power-Down")) + sta350->gpio_power_down = -EINVAL; + + ret = sta350_startup_sequence(sta350); + if (ret < 0) { + dev_err(codec->dev, "Failed to startup device\n"); + return ret; + } + + ret = regulator_bulk_enable(ARRAY_SIZE(sta350->supplies), + sta350->supplies); + if (ret < 0) { + dev_err(codec->dev, "Failed to enable supplies: %d\n", ret); + return ret; + } + + /* + * Tell ASoC what kind of I/O to use to read the registers. ASoC will + * then do the I2C transactions itself. + */ + codec->control_data = sta350->regmap; + + /* + * Chip documentation explicitly requires that the reset values + * of reserved register bits are left untouched. + * Write the register default value to cache for reserved registers, + * so the write to the these registers are suppressed by the cache + * restore code when it skips writes of default registers. + */ + regcache_cache_only(sta350->regmap, true); + regmap_write(sta350->regmap, STA350_CONFC, 0xc2); + regmap_write(sta350->regmap, STA350_CONFE, 0xc2); + regmap_write(sta350->regmap, STA350_CONFF, 0x5c); + regmap_write(sta350->regmap, STA350_MMUTE, 0x10); + regmap_write(sta350->regmap, STA350_AUTO1, 0x60); + regmap_write(sta350->regmap, STA350_AUTO3, 0x00); + regmap_write(sta350->regmap, STA350_C3CFG, 0x40); + regcache_cache_only(sta350->regmap, false); + + /* CONFA */ + if (!pdata->thermal_warning_recovery) + thermal |= STA350_CONFA_TWAB; + if (!pdata->thermal_warning_adjustment) + thermal |= STA350_CONFA_TWRB; + if (!pdata->fault_detect_recovery) + thermal |= STA350_CONFA_FDRB; + regmap_update_bits(sta350->regmap, STA350_CONFA, + STA350_CONFA_TWAB | STA350_CONFA_TWRB | + STA350_CONFA_FDRB, + thermal); + + /* CONFC */ + regmap_update_bits(sta350->regmap, STA350_CONFC, + STA350_CONFC_OM_MASK, + pdata->ffx_power_output_mode + << STA350_CONFC_OM_SHIFT); + regmap_update_bits(sta350->regmap, STA350_CONFC, + STA350_CONFC_CSZ_MASK, + pdata->drop_compensation_ns + << STA350_CONFC_CSZ_SHIFT); + regmap_update_bits(sta350->regmap, + STA350_CONFC, + STA350_CONFC_OCRB, + pdata->oc_warning_adjustment ? + STA350_CONFC_OCRB : 0); + + /* CONFE */ + regmap_update_bits(sta350->regmap, STA350_CONFE, + STA350_CONFE_MPCV, + pdata->max_power_use_mpcc ? + STA350_CONFE_MPCV : 0); + regmap_update_bits(sta350->regmap, STA350_CONFE, + STA350_CONFE_MPC, + pdata->max_power_correction ? + STA350_CONFE_MPC : 0); + regmap_update_bits(sta350->regmap, STA350_CONFE, + STA350_CONFE_AME, + pdata->am_reduction_mode ? + STA350_CONFE_AME : 0); + regmap_update_bits(sta350->regmap, STA350_CONFE, + STA350_CONFE_PWMS, + pdata->odd_pwm_speed_mode ? + STA350_CONFE_PWMS : 0); + regmap_update_bits(sta350->regmap, STA350_CONFE, + STA350_CONFE_DCCV, + pdata->distortion_compensation ? + STA350_CONFE_DCCV : 0); + /* CONFF */ + regmap_update_bits(sta350->regmap, STA350_CONFF, + STA350_CONFF_IDE, + pdata->invalid_input_detect_mute ? + STA350_CONFF_IDE : 0); + regmap_update_bits(sta350->regmap, STA350_CONFF, + STA350_CONFF_OCFG_MASK, + pdata->output_conf + << STA350_CONFF_OCFG_SHIFT); + + /* channel to output mapping */ + regmap_update_bits(sta350->regmap, STA350_C1CFG, + STA350_CxCFG_OM_MASK, + pdata->ch1_output_mapping + << STA350_CxCFG_OM_SHIFT); + regmap_update_bits(sta350->regmap, STA350_C2CFG, + STA350_CxCFG_OM_MASK, + pdata->ch2_output_mapping + << STA350_CxCFG_OM_SHIFT); + regmap_update_bits(sta350->regmap, STA350_C3CFG, + STA350_CxCFG_OM_MASK, + pdata->ch3_output_mapping + << STA350_CxCFG_OM_SHIFT); + + /* initialize coefficient shadow RAM with reset values */ + for (i = 4; i <= 49; i += 5) + sta350->coef_shadow[i] = 0x400000; + for (i = 50; i <= 54; i++) + sta350->coef_shadow[i] = 0x7fffff; + sta350->coef_shadow[55] = 0x5a9df7; + sta350->coef_shadow[56] = 0x7fffff; + sta350->coef_shadow[59] = 0x7fffff; + sta350->coef_shadow[60] = 0x400000; + sta350->coef_shadow[61] = 0x400000; + + sta350_set_bias_level(codec, SND_SOC_BIAS_STANDBY); + /* Bias level configuration will have done an extra enable */ + regulator_bulk_disable(ARRAY_SIZE(sta350->supplies), sta350->supplies); + + return 0; +} + +static int sta350_remove(struct snd_soc_codec *codec) +{ + struct sta350_priv *sta350 = snd_soc_codec_get_drvdata(codec); + + if (gpio_is_valid(sta350->gpio_nreset)) + gpio_set_value(sta350->gpio_nreset, 0); + + if (gpio_is_valid(sta350->gpio_power_down)) + gpio_set_value(sta350->gpio_power_down, 0); + + sta350_set_bias_level(codec, SND_SOC_BIAS_OFF); + regulator_bulk_disable(ARRAY_SIZE(sta350->supplies), sta350->supplies); + + return 0; +} + +static const struct snd_soc_codec_driver sta350_codec = { + .probe = sta350_probe, + .remove = sta350_remove, + .suspend = sta350_suspend, + .resume = sta350_resume, + .set_bias_level = sta350_set_bias_level, + .controls = sta350_snd_controls, + .num_controls = ARRAY_SIZE(sta350_snd_controls), + .dapm_widgets = sta350_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(sta350_dapm_widgets), + .dapm_routes = sta350_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(sta350_dapm_routes), +}; + +static const struct regmap_config sta350_regmap = { + .reg_bits = 8, + .val_bits = 8, + .max_register = STA350_MISC2, + .reg_defaults = sta350_regs, + .num_reg_defaults = ARRAY_SIZE(sta350_regs), + .cache_type = REGCACHE_RBTREE, + .wr_table = &sta350_write_regs, + .rd_table = &sta350_read_regs, + .volatile_table = &sta350_volatile_regs, +}; + +#ifdef CONFIG_OF +static const struct of_device_id st350_dt_ids[] = { + { .compatible = "st,sta350", }, + { } +}; +MODULE_DEVICE_TABLE(of, st350_dt_ids); + +static const char const *sta350_ffx_modes[] = { + [STA350_FFX_PM_DROP_COMP] = "drop-compensation", + [STA350_FFX_PM_TAPERED_COMP] = "tapered-compensation", + [STA350_FFX_PM_FULL_POWER] = "full-power-mode", + [STA350_FFX_PM_VARIABLE_DROP_COMP] = "variable-drop-compensation", +}; + +static int sta350_probe_dt(struct device *dev, struct sta350_priv *sta350) +{ + struct device_node *np = dev->of_node; + struct sta350_platform_data *pdata; + const char *ffx_power_mode; + u16 tmp; + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return -ENOMEM; + + sta350->gpio_nreset = of_get_named_gpio(np, "reset-gpio", 0); + sta350->gpio_power_down = of_get_named_gpio(np, "power-down-gpio", 0); + + of_property_read_u8(np, "st,output-conf", + &pdata->output_conf); + of_property_read_u8(np, "st,ch1-output-mapping", + &pdata->ch1_output_mapping); + of_property_read_u8(np, "st,ch2-output-mapping", + &pdata->ch2_output_mapping); + of_property_read_u8(np, "st,ch3-output-mapping", + &pdata->ch3_output_mapping); + + if (of_get_property(np, "st,thermal-warning-recovery", NULL)) + pdata->thermal_warning_recovery = 1; + if (of_get_property(np, "st,thermal-warning-adjustment", NULL)) + pdata->thermal_warning_adjustment = 1; + if (of_get_property(np, "st,fault-detect-recovery", NULL)) + pdata->fault_detect_recovery = 1; + + pdata->ffx_power_output_mode = STA350_FFX_PM_VARIABLE_DROP_COMP; + if (!of_property_read_string(np, "st,ffx-power-output-mode", + &ffx_power_mode)) { + int i, mode = -EINVAL; + + for (i = 0; i < ARRAY_SIZE(sta350_ffx_modes); i++) + if (!strcasecmp(ffx_power_mode, sta350_ffx_modes[i])) + mode = i; + + if (mode < 0) + dev_warn(dev, "Unsupported ffx output mode: %s\n", + ffx_power_mode); + else + pdata->ffx_power_output_mode = mode; + } + + tmp = 140; + of_property_read_u16(np, "st,drop-compensation-ns", &tmp); + pdata->drop_compensation_ns = clamp_t(u16, tmp, 0, 300) / 20; + + if (of_get_property(np, "st,overcurrent-warning-adjustment", NULL)) + pdata->oc_warning_adjustment = 1; + + /* CONFE */ + if (of_get_property(np, "st,max-power-use-mpcc", NULL)) + pdata->max_power_use_mpcc = 1; + + if (of_get_property(np, "st,max-power-correction", NULL)) + pdata->max_power_correction = 1; + + if (of_get_property(np, "st,am-reduction-mode", NULL)) + pdata->am_reduction_mode = 1; + + if (of_get_property(np, "st,odd-pwm-speed-mode", NULL)) + pdata->odd_pwm_speed_mode = 1; + + if (of_get_property(np, "st,distortion-compensation", NULL)) + pdata->distortion_compensation = 1; + + /* CONFF */ + if (of_get_property(np, "st,invalid-input-detect-mute", NULL)) + pdata->invalid_input_detect_mute = 1; + + sta350->pdata = pdata; + + return 0; +} +#endif + +static int sta350_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct sta350_priv *sta350; + int ret, i; + + sta350 = devm_kzalloc(&i2c->dev, sizeof(struct sta350_priv), + GFP_KERNEL); + if (!sta350) + return -ENOMEM; + + sta350->pdata = dev_get_platdata(&i2c->dev); + sta350->gpio_nreset = -EINVAL; + +#ifdef CONFIG_OF + if (of_match_device(st350_dt_ids, &i2c->dev)) { + ret = sta350_probe_dt(&i2c->dev, sta350); + if (ret < 0) + return ret; + } +#endif + + /* regulators */ + for (i = 0; i < ARRAY_SIZE(sta350->supplies); i++) + sta350->supplies[i].supply = sta350_supply_names[i]; + + ret = devm_regulator_bulk_get(&i2c->dev, ARRAY_SIZE(sta350->supplies), + sta350->supplies); + if (ret < 0) { + dev_err(&i2c->dev, "Failed to request supplies: %d\n", ret); + return ret; + } + + sta350->regmap = devm_regmap_init_i2c(i2c, &sta350_regmap); + if (IS_ERR(sta350->regmap)) { + ret = PTR_ERR(sta350->regmap); + dev_err(&i2c->dev, "Failed to init regmap: %d\n", ret); + return ret; + } + + i2c_set_clientdata(i2c, sta350); + + ret = snd_soc_register_codec(&i2c->dev, &sta350_codec, &sta350_dai, 1); + if (ret < 0) + dev_err(&i2c->dev, "Failed to register codec (%d)\n", ret); + + return ret; +} + +static int sta350_i2c_remove(struct i2c_client *client) +{ + snd_soc_unregister_codec(&client->dev); + return 0; +} + +static const struct i2c_device_id sta350_i2c_id[] = { + { "sta350", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, sta350_i2c_id); + +static struct i2c_driver sta350_i2c_driver = { + .driver = { + .name = "sta350", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(st350_dt_ids), + }, + .probe = sta350_i2c_probe, + .remove = sta350_i2c_remove, + .id_table = sta350_i2c_id, +}; + +module_i2c_driver(sta350_i2c_driver); + +MODULE_DESCRIPTION("ASoC STA350 driver"); +MODULE_AUTHOR("Sven Brandau info@brandau.biz"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/sta350.h b/sound/soc/codecs/sta350.h new file mode 100644 index 0000000..c3248f0 --- /dev/null +++ b/sound/soc/codecs/sta350.h @@ -0,0 +1,228 @@ +/* + * Codec driver for ST STA350 2.1-channel high-efficiency digital audio system + * + * Copyright: 2011 Raumfeld GmbH + * Author: Sven Brandau info@brandau.biz + * + * based on code from: + * Raumfeld GmbH + * Johannes Stezenbach js@sig21.net + * Wolfson Microelectronics PLC. + * Mark Brown broonie@opensource.wolfsonmicro.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ +#ifndef _ASOC_STA_350_H +#define _ASOC_STA_350_H + +/* STA50 register addresses */ + +#define STA350_REGISTER_COUNT 0x4D +#define STA350_COEF_COUNT 62 + +#define STA350_CONFA 0x00 +#define STA350_CONFB 0x01 +#define STA350_CONFC 0x02 +#define STA350_CONFD 0x03 +#define STA350_CONFE 0x04 +#define STA350_CONFF 0x05 +#define STA350_MMUTE 0x06 +#define STA350_MVOL 0x07 +#define STA350_C1VOL 0x08 +#define STA350_C2VOL 0x09 +#define STA350_C3VOL 0x0a +#define STA350_AUTO1 0x0b +#define STA350_AUTO2 0x0c +#define STA350_AUTO3 0x0d +#define STA350_C1CFG 0x0e +#define STA350_C2CFG 0x0f +#define STA350_C3CFG 0x10 +#define STA350_TONE 0x11 +#define STA350_L1AR 0x12 +#define STA350_L1ATRT 0x13 +#define STA350_L2AR 0x14 +#define STA350_L2ATRT 0x15 +#define STA350_CFADDR2 0x16 +#define STA350_B1CF1 0x17 +#define STA350_B1CF2 0x18 +#define STA350_B1CF3 0x19 +#define STA350_B2CF1 0x1a +#define STA350_B2CF2 0x1b +#define STA350_B2CF3 0x1c +#define STA350_A1CF1 0x1d +#define STA350_A1CF2 0x1e +#define STA350_A1CF3 0x1f +#define STA350_A2CF1 0x20 +#define STA350_A2CF2 0x21 +#define STA350_A2CF3 0x22 +#define STA350_B0CF1 0x23 +#define STA350_B0CF2 0x24 +#define STA350_B0CF3 0x25 +#define STA350_CFUD 0x26 +#define STA350_MPCC1 0x27 +#define STA350_MPCC2 0x28 +#define STA350_DCC1 0x29 +#define STA350_DCC2 0x2a +#define STA350_FDRC1 0x2b +#define STA350_FDRC2 0x2c +#define STA350_STATUS 0x2d +/* reserved: 0x2d - 0x30 */ +#define STA350_EQCFG 0x31 +#define STA350_EATH1 0x32 +#define STA350_ERTH1 0x33 +#define STA350_EATH2 0x34 +#define STA350_ERTH2 0x35 +#define STA350_CONFX 0x36 +#define STA350_SVCA 0x37 +#define STA350_SVCB 0x38 +#define STA350_RMS0A 0x39 +#define STA350_RMS0B 0x3a +#define STA350_RMS0C 0x3b +#define STA350_RMS1A 0x3c +#define STA350_RMS1B 0x3d +#define STA350_RMS1C 0x3e +#define STA350_EVOLRES 0x3f +/* reserved: 0x40 - 0x47 */ +#define STA350_NSHAPE 0x48 +#define STA350_CTXB4B1 0x49 +#define STA350_CTXB7B5 0x4a +#define STA350_MISC1 0x4b +#define STA350_MISC2 0x4c + +/* 0x00 CONFA */ +#define STA350_CONFA_MCS_MASK 0x03 +#define STA350_CONFA_MCS_SHIFT 0 +#define STA350_CONFA_IR_MASK 0x18 +#define STA350_CONFA_IR_SHIFT 3 +#define STA350_CONFA_TWRB BIT(5) +#define STA350_CONFA_TWAB BIT(6) +#define STA350_CONFA_FDRB BIT(7) + +/* 0x01 CONFB */ +#define STA350_CONFB_SAI_MASK 0x0f +#define STA350_CONFB_SAI_SHIFT 0 +#define STA350_CONFB_SAIFB BIT(4) +#define STA350_CONFB_DSCKE BIT(5) +#define STA350_CONFB_C1IM BIT(6) +#define STA350_CONFB_C2IM BIT(7) + +/* 0x02 CONFC */ +#define STA350_CONFC_OM_MASK 0x03 +#define STA350_CONFC_OM_SHIFT 0 +#define STA350_CONFC_CSZ_MASK 0x3c +#define STA350_CONFC_CSZ_SHIFT 2 +#define STA350_CONFC_OCRB BIT(7) + +/* 0x03 CONFD */ +#define STA350_CONFD_HPB_SHIFT 0 +#define STA350_CONFD_DEMP_SHIFT 1 +#define STA350_CONFD_DSPB_SHIFT 2 +#define STA350_CONFD_PSL_SHIFT 3 +#define STA350_CONFD_BQL_SHIFT 4 +#define STA350_CONFD_DRC_SHIFT 5 +#define STA350_CONFD_ZDE_SHIFT 6 +#define STA350_CONFD_SME_SHIFT 7 + +/* 0x04 CONFE */ +#define STA350_CONFE_MPCV BIT(0) +#define STA350_CONFE_MPCV_SHIFT 0 +#define STA350_CONFE_MPC BIT(1) +#define STA350_CONFE_MPC_SHIFT 1 +#define STA350_CONFE_NSBW BIT(2) +#define STA350_CONFE_NSBW_SHIFT 2 +#define STA350_CONFE_AME BIT(3) +#define STA350_CONFE_AME_SHIFT 3 +#define STA350_CONFE_PWMS BIT(4) +#define STA350_CONFE_PWMS_SHIFT 4 +#define STA350_CONFE_DCCV BIT(5) +#define STA350_CONFE_DCCV_SHIFT 5 +#define STA350_CONFE_ZCE BIT(6) +#define STA350_CONFE_ZCE_SHIFT 6 +#define STA350_CONFE_SVE BIT(7) +#define STA350_CONFE_SVE_SHIFT 7 + +/* 0x05 CONFF */ +#define STA350_CONFF_OCFG_MASK 0x03 +#define STA350_CONFF_OCFG_SHIFT 0 +#define STA350_CONFF_IDE BIT(2) +#define STA350_CONFF_BCLE BIT(3) +#define STA350_CONFF_LDTE BIT(4) +#define STA350_CONFF_ECLE BIT(5) +#define STA350_CONFF_PWDN BIT(6) +#define STA350_CONFF_EAPD BIT(7) + +/* 0x06 MMUTE */ +#define STA350_MMUTE_MMUTE 0x01 +#define STA350_MMUTE_MMUTE_SHIFT 0 +#define STA350_MMUTE_C1M 0x02 +#define STA350_MMUTE_C1M_SHIFT 1 +#define STA350_MMUTE_C2M 0x04 +#define STA350_MMUTE_C2M_SHIFT 2 +#define STA350_MMUTE_C3M 0x08 +#define STA350_MMUTE_C3M_SHIFT 3 +#define STA350_MMUTE_LOC_MASK 0xC0 +#define STA350_MMUTE_LOC_SHIFT 6 + +/* 0x0b AUTO1 */ +#define STA350_AUTO1_AMGC_MASK 0x30 +#define STA350_AUTO1_AMGC_SHIFT 4 + +/* 0x0c AUTO2 */ +#define STA350_AUTO2_AMAME 0x01 +#define STA350_AUTO2_AMAM_MASK 0x0e +#define STA350_AUTO2_AMAM_SHIFT 1 +#define STA350_AUTO2_XO_MASK 0xf0 +#define STA350_AUTO2_XO_SHIFT 4 + +/* 0x0d AUTO3 */ +#define STA350_AUTO3_PEQ_MASK 0x1f +#define STA350_AUTO3_PEQ_SHIFT 0 + +/* 0x0e 0x0f 0x10 CxCFG */ +#define STA350_CxCFG_TCB_SHIFT 0 +#define STA350_CxCFG_EQBP_SHIFT 1 +#define STA350_CxCFG_VBP_SHIFT 2 +#define STA350_CxCFG_BO_SHIFT 3 +#define STA350_CxCFG_LS_SHIFT 4 +#define STA350_CxCFG_OM_MASK 0xc0 +#define STA350_CxCFG_OM_SHIFT 6 + +/* 0x11 TONE */ +#define STA350_TONE_BTC_SHIFT 0 +#define STA350_TONE_TTC_SHIFT 4 + +/* 0x12 0x13 0x14 0x15 limiter attack/release */ +#define STA350_LxA_SHIFT 0 +#define STA350_LxR_SHIFT 4 + +/* 0x26 CFUD */ +#define STA350_CFUD_W1 0x01 +#define STA350_CFUD_WA 0x02 +#define STA350_CFUD_R1 0x04 +#define STA350_CFUD_RA 0x08 + + +/* biquad filter coefficient table offsets */ +#define STA350_C1_BQ_BASE 0 +#define STA350_C2_BQ_BASE 20 +#define STA350_CH_BQ_NUM 4 +#define STA350_BQ_NUM_COEF 5 +#define STA350_XO_HP_BQ_BASE 40 +#define STA350_XO_LP_BQ_BASE 45 +#define STA350_C1_PRESCALE 50 +#define STA350_C2_PRESCALE 51 +#define STA350_C1_POSTSCALE 52 +#define STA350_C2_POSTSCALE 53 +#define STA350_C3_POSTSCALE 54 +#define STA350_TW_POSTSCALE 55 +#define STA350_C1_MIX1 56 +#define STA350_C1_MIX2 57 +#define STA350_C2_MIX1 58 +#define STA350_C2_MIX2 59 +#define STA350_C3_MIX1 60 +#define STA350_C3_MIX2 61 + +#endif /* _ASOC_STA_350_H */