[PATCH v8 00/13] Introduce STM32 Firewall framework
Introduce STM32 Firewall framework for STM32MP1x and STM32MP2x platforms. STM32MP1x(ETZPC) and STM32MP2x(RIFSC) Firewall controllers register to the framework to offer firewall services such as access granting.
This series of patches is a new approach on the previous STM32 system bus, history is available here: https://lore.kernel.org/lkml/20230127164040.1047583/
The need for such framework arises from the fact that there are now multiple hardware firewalls implemented across multiple products. Drivers are shared between different products, using the same code. When it comes to firewalls, the purpose mostly stays the same: Protect hardware resources. But the implementation differs, and there are multiple types of firewalls: peripheral, memory, ...
Some hardware firewall controllers such as the RIFSC implemented on STM32MP2x platforms may require to take ownership of a resource before being able to use it, hence the requirement for firewall services to take/release the ownership of such resources.
On the other hand, hardware firewall configurations are becoming more and more complex. These mecanisms prevent platform crashes or other firewall-related incoveniences by denying access to some resources.
The stm32 firewall framework offers an API that is defined in firewall controllers drivers to best fit the specificity of each firewall.
For every peripherals protected by either the ETZPC or the RIFSC, the firewall framework checks the firewall controlelr registers to see if the peripheral's access is granted to the Linux kernel. If not, the peripheral is configured as secure, the node is marked populated, so that the driver is not probed for that device.
The firewall framework relies on the access-controller device tree binding. It is used by peripherals to reference a domain access controller. In this case a firewall controller. The bus uses the ID referenced by the access-controller property to know where to look in the firewall to get the security configuration for the peripheral. This allows a device tree description rather than a hardcoded peripheral table in the bus driver.
The STM32 ETZPC device is responsible for filtering accesses based on security level, or co-processor isolation for any resource connected to it.
The RIFSC is responsible for filtering accesses based on Compartment ID / security level / privilege level for any resource connected to it.
STM32MP13/15/25 SoC device tree files are updated in this series to implement this mecanism.
Changes in V8: - Add missing "simple-bus" compatible in STM32MP13/25 SoC device tree files for the ETZPC/RIFSC nodes - Add missing dependency on OF for OF_DYNAMIC that is selected by STM32_FIREWALL
Changes in V7: - Separate indentation changes from access-controllers changes in the device tree file commits - Select OF_DYNAMIC when STM32_FIREWALL is set in order to use of_detach_node() in the firewall framework - Handle previously non-present RNG and HASH nodes in the STM32MP13 device tree file
Changes in V6: - Rename access-controller to access-controllers - Remove access-controller-provider - Update device trees and other bindings accordingly - Rework ETZPC/RIFSC bindings to define what access-controllers cells contain inside #access-controller-cells - Some other minor fixes
Changes in V5: - Integrate and rework the "feature-domains" binding patch in this patchset. The binding is renamed to "access-controller" - Rename every feature-domain* reference to access-control* ones - Correct loop bug and missing select STM32_FIREWALL in 32-bit platform Kconfig
Changes in V4: - Fix typo in commit message and YAML check errors in "dt-bindings: Document common device controller bindings" Note: This patch should be ignored as stated in the cover letter. I've done this to avoid errors on this series of patch - Correct code syntax/style issues reported by Simon Horman - Added Jonathan's tag for IIO on the treewide patch
Changes in V3:
Change incorrect ordering for bindings commits leading to an error while running "make DT_CHECKER_FLAGS=-m dt_binding_check"
Changes in V2:
generic: - Add fw_devlink dependency for "feature-domains" property.
bindings: - Corrected YAMLS errors highlighted by Rob's robot - Firewall controllers YAMLs no longer define the maxItems for the "feature-domains" property - Renamed st,stm32-rifsc.yaml to st,stm32mp25-rifsc.yaml - Fix examples in YAML files - Change feature-domains maxItems to 2 in firewall consumer files as there should not be more than 2 entries for now - Declare "feature-domain-names" as an optional property for firewall controllers child nodes. - Add missing "feature-domains" property declaration in bosch,m_can.yaml and st,stm32-cryp.yaml files
firewall framework: - Support multiple entries for "feature-domains" property - Better handle the device-tree parsing using phandle+args APIs - Remove "resource firewall" type - Add a field for the name of the firewall entry - Fix licenses RIFSC: - Add controller name - Driver is now a module_platform_driver - Fix license
ETZPC: - Add controller name - Driver is now a module_platform_driver - Fix license
Device trees: - Fix rifsc node name - Move the "ranges" property under the "feature-domains" one
Gatien Chevallier (12): dt-bindings: treewide: add access-controllers description dt-bindings: bus: document RIFSC dt-bindings: bus: document ETZPC firewall: introduce stm32_firewall framework of: property: fw_devlink: Add support for "access-controller" bus: rifsc: introduce RIFSC firewall controller driver arm64: dts: st: add RIFSC as an access controller for STM32MP25x boards bus: etzpc: introduce ETZPC firewall controller driver ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards ARM: dts: stm32: put ETZPC as an access controller for STM32MP15x boards ARM: dts: stm32: add ETZPC as a system bus for STM32MP13x boards ARM: dts: stm32: put ETZPC as an access controller for STM32MP13x boards
Oleksii Moisieiev (1): dt-bindings: document generic access controllers
.../access-controllers.yaml | 84 + .../bindings/bus/st,stm32-etzpc.yaml | 87 + .../bindings/bus/st,stm32mp25-rifsc.yaml | 96 + .../bindings/crypto/st,stm32-cryp.yaml | 4 + .../bindings/crypto/st,stm32-hash.yaml | 4 + .../devicetree/bindings/dma/st,stm32-dma.yaml | 4 + .../bindings/dma/st,stm32-dmamux.yaml | 4 + .../devicetree/bindings/i2c/st,stm32-i2c.yaml | 4 + .../bindings/iio/adc/st,stm32-adc.yaml | 4 + .../bindings/iio/adc/st,stm32-dfsdm-adc.yaml | 4 + .../bindings/iio/dac/st,stm32-dac.yaml | 4 + .../bindings/media/cec/st,stm32-cec.yaml | 4 + .../bindings/media/st,stm32-dcmi.yaml | 4 + .../memory-controllers/st,stm32-fmc2-ebi.yaml | 4 + .../bindings/mfd/st,stm32-lptimer.yaml | 4 + .../bindings/mfd/st,stm32-timers.yaml | 4 + .../devicetree/bindings/mmc/arm,pl18x.yaml | 4 + .../bindings/net/can/bosch,m_can.yaml | 4 + .../devicetree/bindings/net/stm32-dwmac.yaml | 4 + .../bindings/phy/phy-stm32-usbphyc.yaml | 4 + .../bindings/regulator/st,stm32-vrefbuf.yaml | 4 + .../devicetree/bindings/rng/st,stm32-rng.yaml | 4 + .../bindings/serial/st,stm32-uart.yaml | 4 + .../bindings/sound/st,stm32-i2s.yaml | 4 + .../bindings/sound/st,stm32-sai.yaml | 4 + .../bindings/sound/st,stm32-spdifrx.yaml | 4 + .../bindings/spi/st,stm32-qspi.yaml | 4 + .../devicetree/bindings/spi/st,stm32-spi.yaml | 4 + .../devicetree/bindings/usb/dwc2.yaml | 4 + MAINTAINERS | 7 + arch/arm/boot/dts/st/stm32mp131.dtsi | 1063 ++++--- arch/arm/boot/dts/st/stm32mp133.dtsi | 51 +- arch/arm/boot/dts/st/stm32mp13xc.dtsi | 19 +- arch/arm/boot/dts/st/stm32mp13xf.dtsi | 19 +- arch/arm/boot/dts/st/stm32mp151.dtsi | 2756 +++++++++-------- arch/arm/boot/dts/st/stm32mp153.dtsi | 52 +- arch/arm/boot/dts/st/stm32mp15xc.dtsi | 19 +- arch/arm/mach-stm32/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + arch/arm64/boot/dts/st/stm32mp251.dtsi | 7 +- drivers/bus/Kconfig | 10 + drivers/bus/Makefile | 1 + drivers/bus/stm32_etzpc.c | 141 + drivers/bus/stm32_firewall.c | 294 ++ drivers/bus/stm32_firewall.h | 83 + drivers/bus/stm32_rifsc.c | 252 ++ drivers/of/property.c | 2 + include/linux/bus/stm32_firewall_device.h | 141 + 48 files changed, 3352 insertions(+), 1938 deletions(-) create mode 100644 Documentation/devicetree/bindings/access-controllers/access-controllers.yaml create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml create mode 100644 Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml create mode 100644 drivers/bus/stm32_etzpc.c create mode 100644 drivers/bus/stm32_firewall.c create mode 100644 drivers/bus/stm32_firewall.h create mode 100644 drivers/bus/stm32_rifsc.c create mode 100644 include/linux/bus/stm32_firewall_device.h
From: Oleksii Moisieiev Oleksii_Moisieiev@epam.com
Introducing of the generic access controllers bindings for the access controller provider and consumer devices. Those bindings are intended to allow a better handling of accesses to resources in a hardware architecture supporting several compartments.
This patch is based on [1]. It is integrated in this patchset as it provides a use-case for it.
Diffs with [1]: - Rename feature-domain* properties to access-control* to narrow down the scope of the binding - YAML errors and typos corrected. - Example updated - Some rephrasing in the binding description
[1]: https://lore.kernel.org/lkml/0c0a82bb-18ae-d057-562b
Signed-off-by: Oleksii Moisieiev oleksii_moisieiev@epam.com Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V6: - Renamed access-controller to access-controllers - Example updated - Removal of access-control-provider property
Changes in V5: - Diffs with [1] - Discarded the [IGNORE] tag as the patch is now part of the patchset
.../access-controllers.yaml | 84 +++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 Documentation/devicetree/bindings/access-controllers/access-controllers.yaml
diff --git a/Documentation/devicetree/bindings/access-controllers/access-controllers.yaml b/Documentation/devicetree/bindings/access-controllers/access-controllers.yaml new file mode 100644 index 000000000000..99e2865f0e46 --- /dev/null +++ b/Documentation/devicetree/bindings/access-controllers/access-controllers.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/access-controllers/access-controllers.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic Domain Access Controllers + +maintainers: + - Oleksii Moisieiev oleksii_moisieiev@epam.com + +description: |+ + Common access controllers properties + + Access controllers are in charge of stating which of the hardware blocks under + their responsibility (their domain) can be accesssed by which compartment. A + compartment can be a cluster of CPUs (or coprocessors), a range of addresses + or a group of hardware blocks. An access controller's domain is the set of + resources covered by the access controller. + + This device tree binding can be used to bind devices to their access + controller provided by access-controllers property. In this case, the device + is a consumer and the access controller is the provider. + + An access controller can be represented by any node in the device tree and + can provide one or more configuration parameters, needed to control parameters + of the consumer device. A consumer node can refer to the provider by phandle + and a set of phandle arguments, specified by '#access-controller-cells' + property in the access controller node. + + Access controllers are typically used to set/read the permissions of a + hardware block and grant access to it. Any of which depends on the access + controller. The capabilities of each access controller are defined by the + binding of the access controller device. + + Each node can be a consumer for the several access controllers. + +# always select the core schema +select: true + +properties: + "#access-controller-cells": + description: + Number of cells in an access-controllers specifier; + Can be any value as specified by device tree binding documentation + of a particular provider. The node is an access controller. + + access-controller-names: + $ref: /schemas/types.yaml#/definitions/string-array + description: + A list of access-controllers names, sorted in the same order as + access-controllers entries. Consumer drivers will use + access-controller-names to match with existing access-controllers entries. + + access-controllers: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + A list of access controller specifiers, as defined by the + bindings of the access-controllers provider. + +additionalProperties: true + +examples: + - | + clock_controller: access-controllers@50000 { + reg = <0x50000 0x400>; + #access-controller-cells = <2>; + }; + + bus_controller: bus@60000 { + reg = <0x60000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + #access-controller-cells = <3>; + + uart4: serial@60100 { + reg = <0x60100 0x400>; + clocks = <&clk_serial>; + access-controllers = <&clock_controller 1 2>, + <&bus_controller 1 3 5>; + access-controller-names = "clock", "bus"; + }; + };
On Tue, 12 Dec 2023 16:23:44 +0100, Gatien Chevallier wrote:
Reviewed-by: Rob Herring robh@kernel.org
access-controllers is an optional property that allows a peripheral to refer to one or more domain access controller(s).
Description of this property is added to all peripheral binding files of the peripheral under the STM32 firewall controller. It allows an accurate representation of the hardware, where various peripherals are connected to a firewall bus. The firewall can then check the peripheral accesses before allowing its device to probe.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V6: - Minor changes in commit message - Renamed access-controller to access-controllers
Changes in V5: - Discarded review tags as the content has changed - Renamed feature-domains to access-controller
Changes in V4: - Added Jonathan's tag for IIO
Changes in V2: - Add missing "feature-domains" property declaration in bosch,m_can.yaml and st,stm32-cryp.yaml files
Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml | 4 ++++ Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml | 4 ++++ Documentation/devicetree/bindings/dma/st,stm32-dma.yaml | 4 ++++ Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml | 4 ++++ Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml | 4 ++++ Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml | 4 ++++ .../devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml | 4 ++++ Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml | 4 ++++ Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml | 4 ++++ Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml | 4 ++++ .../bindings/memory-controllers/st,stm32-fmc2-ebi.yaml | 4 ++++ Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml | 4 ++++ Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml | 4 ++++ Documentation/devicetree/bindings/mmc/arm,pl18x.yaml | 4 ++++ Documentation/devicetree/bindings/net/can/bosch,m_can.yaml | 4 ++++ Documentation/devicetree/bindings/net/stm32-dwmac.yaml | 4 ++++ Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml | 4 ++++ .../devicetree/bindings/regulator/st,stm32-vrefbuf.yaml | 4 ++++ Documentation/devicetree/bindings/rng/st,stm32-rng.yaml | 4 ++++ Documentation/devicetree/bindings/serial/st,stm32-uart.yaml | 4 ++++ Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml | 4 ++++ Documentation/devicetree/bindings/sound/st,stm32-sai.yaml | 4 ++++ Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml | 4 ++++ Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml | 4 ++++ Documentation/devicetree/bindings/spi/st,stm32-spi.yaml | 4 ++++ Documentation/devicetree/bindings/usb/dwc2.yaml | 4 ++++ 26 files changed, 104 insertions(+)
diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml index 0ddeb8a9a7a0..27354658d054 100644 --- a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml +++ b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml @@ -46,6 +46,10 @@ properties: power-domains: maxItems: 1
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml b/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml index ac480765cde0..822318414095 100644 --- a/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml +++ b/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml @@ -51,6 +51,10 @@ properties: power-domains: maxItems: 1
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml b/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml index 329847ef096a..ff935a0068ec 100644 --- a/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml +++ b/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml @@ -82,6 +82,10 @@ properties: description: if defined, it indicates that the controller supports memory-to-memory transfer
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml b/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml index e722fbcd8a5f..ddf82bf1e71a 100644 --- a/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml +++ b/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml @@ -28,6 +28,10 @@ properties: resets: maxItems: 1
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml index 94b75d9f66cd..39fad8f7df44 100644 --- a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml +++ b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml @@ -99,6 +99,10 @@ properties:
wakeup-source: true
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml index 995cbf8cefc6..ec34c48d4878 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml @@ -93,6 +93,10 @@ properties: '#size-cells': const: 0
+ access-controllers: + minItems: 1 + maxItems: 2 + allOf: - if: properties: diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml index 1970503389aa..c1b1324fa132 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml @@ -59,6 +59,10 @@ properties: If not, SPI CLKOUT frequency will not be accurate. maximum: 20000000
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml index 04045b932bd2..b15de4eb209c 100644 --- a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml +++ b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml @@ -45,6 +45,10 @@ properties: '#size-cells': const: 0
+ access-controllers: + minItems: 1 + maxItems: 2 + additionalProperties: false
required: diff --git a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml index 2314a9a14650..1d930d9e10fd 100644 --- a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml +++ b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml @@ -29,6 +29,10 @@ properties: - const: cec - const: hdmi-cec
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml index 6b3e413cedb2..34147127192f 100644 --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml @@ -36,6 +36,10 @@ properties: resets: maxItems: 1
+ access-controllers: + minItems: 1 + maxItems: 2 + port: $ref: /schemas/graph.yaml#/$defs/port-base unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml index 14f1833d37c9..deef455bfd21 100644 --- a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml +++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml @@ -45,6 +45,10 @@ properties: Reflects the memory layout with four integer values per bank. Format: <bank-number> 0 <address of the bank> <size>
+ access-controllers: + minItems: 1 + maxItems: 2 + patternProperties: "^.*@[0-4],[a-f0-9]+$": additionalProperties: true diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml index 27329c5dc38e..d41308856408 100644 --- a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml +++ b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml @@ -44,6 +44,10 @@ properties:
wakeup-source: true
+ access-controllers: + minItems: 1 + maxItems: 2 + pwm: type: object additionalProperties: false diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml index f84e09a5743b..b0e438ff4950 100644 --- a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml +++ b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml @@ -67,6 +67,10 @@ properties: "#size-cells": const: 0
+ access-controllers: + minItems: 1 + maxItems: 2 + pwm: type: object additionalProperties: false diff --git a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml index 2459a55ed540..5644927be810 100644 --- a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml +++ b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml @@ -79,6 +79,10 @@ properties: - const: rx - const: tx
+ access-controllers: + minItems: 1 + maxItems: 2 + power-domains: true
resets: diff --git a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml index f9ffb963d6b1..c4887522e8fe 100644 --- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml +++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml @@ -118,6 +118,10 @@ properties: phys: maxItems: 1
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml index fc8c96b08d7d..f2714b5b6cf4 100644 --- a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml @@ -93,6 +93,10 @@ properties: select RCC clock instead of ETH_REF_CLK. type: boolean
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - clocks diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml index 24a3dbde223b..ceea122ae1a6 100644 --- a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml +++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml @@ -55,6 +55,10 @@ properties: description: number of clock cells for ck_usbo_48m consumer const: 0
+ access-controllers: + minItems: 1 + maxItems: 2 + # Required child nodes:
patternProperties: diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml index 05f4ad2c7d3a..6ceaffb45dc9 100644 --- a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml +++ b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml @@ -30,6 +30,10 @@ properties: vdda-supply: description: phandle to the vdda input analog voltage.
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml b/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml index 717f6b321f88..340d01d481d1 100644 --- a/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml +++ b/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml @@ -37,6 +37,10 @@ properties: description: If set, the RNG configuration in RNG_CR, RNG_HTCR and RNG_NSCR will be locked.
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml index 1df8ffe95fc6..1de03af4ead1 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml @@ -70,6 +70,10 @@ properties: enum: [1, 2, 4, 8, 12, 14, 16] default: 8
+ access-controllers: + minItems: 1 + maxItems: 2 + allOf: - $ref: rs485.yaml# - $ref: serial.yaml# diff --git a/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml b/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml index b9111d375b93..8978f6bd63e5 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml +++ b/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml @@ -65,6 +65,10 @@ properties: $ref: audio-graph-port.yaml# unevaluatedProperties: false
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - "#sound-dai-cells" diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml index 59df8a832310..b46a4778807d 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml @@ -48,6 +48,10 @@ properties: clock-names: maxItems: 3
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml index bc48151b9adb..3dedc81ec12f 100644 --- a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml +++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml @@ -50,6 +50,10 @@ properties: resets: maxItems: 1
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - "#sound-dai-cells" diff --git a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml index 8bba965a9ae6..3f1a27efff80 100644 --- a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml +++ b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml @@ -46,6 +46,10 @@ properties: - const: tx - const: rx
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml index ae0f082bd377..0b303bf5c02c 100644 --- a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml +++ b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml @@ -50,6 +50,10 @@ properties: - const: rx - const: tx
+ access-controllers: + minItems: 1 + maxItems: 2 + required: - compatible - reg diff --git a/Documentation/devicetree/bindings/usb/dwc2.yaml b/Documentation/devicetree/bindings/usb/dwc2.yaml index 0a5c98ea711d..88c077673c8b 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.yaml +++ b/Documentation/devicetree/bindings/usb/dwc2.yaml @@ -172,6 +172,10 @@ properties:
tpl-support: true
+ access-controllers: + minItems: 1 + maxItems: 2 + dependencies: port: [ usb-role-switch ] role-switch-default-mode: [ usb-role-switch ]
On Tue, Dec 12, 2023 at 04:23:45PM +0100, Gatien Chevallier wrote:
Acked-by: Wolfram Sang wsa+renesas@sang-engineering.com # for I2C
Document RIFSC (RIF security controller). RIFSC is a firewall controller composed of different kinds of hardware resources.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V6: - Renamed access-controller to access-controllers - Removal of access-control-provider property - Removal of access-controller and access-controller-names declaration in the patternProperties field. Add additionalProperties: true in this field.
Changes in V5: - Renamed feature-domain* to access-control*
Changes in V2: - Corrected errors highlighted by Rob's robot - No longer define the maxItems for the "feature-domains" property - Fix example (node name, status) - Declare "feature-domain-names" as an optional property for child nodes - Fix description of "feature-domains" property
.../bindings/bus/st,stm32mp25-rifsc.yaml | 96 +++++++++++++++++++ 1 file changed, 96 insertions(+) create mode 100644 Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml
diff --git a/Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml b/Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml new file mode 100644 index 000000000000..95aa7f04c739 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml @@ -0,0 +1,96 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bus/st,stm32mp25-rifsc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STM32 Resource isolation framework security controller + +maintainers: + - Gatien Chevallier gatien.chevallier@foss.st.com + +description: | + Resource isolation framework (RIF) is a comprehensive set of hardware blocks + designed to enforce and manage isolation of STM32 hardware resources like + memory and peripherals. + + The RIFSC (RIF security controller) is composed of three sets of registers, + each managing a specific set of hardware resources: + - RISC registers associated with RISUP logic (resource isolation device unit + for peripherals), assign all non-RIF aware peripherals to zero, one or + any security domains (secure, privilege, compartment). + - RIMC registers: associated with RIMU logic (resource isolation master + unit), assign all non RIF-aware bus master to one security domain by + setting secure, privileged and compartment information on the system bus. + Alternatively, the RISUP logic controlling the device port access to a + peripheral can assign target bus attributes to this peripheral master port + (supported attribute: CID). + - RISC registers associated with RISAL logic (resource isolation device unit + for address space - Lite version), assign address space subregions to one + security domains (secure, privilege, compartment). + +properties: + compatible: + contains: + const: st,stm32mp25-rifsc + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + ranges: true + + "#access-controller-cells": + const: 1 + description: + Contains the firewall ID associated to the peripheral. + +patternProperties: + "^.*@[0-9a-f]+$": + description: Peripherals + type: object + + additionalProperties: true + + required: + - access-controllers + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - "#access-controller-cells" + - ranges + +additionalProperties: false + +examples: + - | + // In this example, the usart2 device refers to rifsc as its domain + // controller. + // Access rights are verified before creating devices. + + #include <dt-bindings/interrupt-controller/arm-gic.h> + + rifsc: bus@42080000 { + compatible = "st,stm32mp25-rifsc"; + reg = <0x42080000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + #access-controller-cells = <1>; + ranges; + + usart2: serial@400e0000 { + compatible = "st,stm32h7-uart"; + reg = <0x400e0000 0x400>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ck_flexgen_08>; + access-controllers = <&rifsc 32>; + }; + };
On Tue, Dec 12, 2023 at 04:23:46PM +0100, Gatien Chevallier wrote:
This needs to be exact and include 'simple-bus'. You'll need a custom 'select' with the above to avoid matching all other 'simple-bus' cases.
With that,
Reviewed-by: Rob Herring robh@kernel.org
Document ETZPC (Extended TrustZone protection controller). ETZPC is a firewall controller.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V6: - Renamed access-controller to access-controllers - Removal of access-control-provider property - Removal of access-controller and access-controller-names declaration in the patternProperties field. Add additionalProperties: true in this field.
Changes in V5: - Renamed feature-domain* to access-control*
Changes in V2: - Corrected errors highlighted by Rob's robot - No longer define the maxItems for the "feature-domains" property - Fix example (node name, status) - Declare "feature-domain-names" as an optional property for child nodes - Fix description of "feature-domains" property - Reordered the properties so it matches ETZPC - Add missing "feature-domain-controller" property
.../bindings/bus/st,stm32-etzpc.yaml | 87 +++++++++++++++++++ 1 file changed, 87 insertions(+) create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml
diff --git a/Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml b/Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml new file mode 100644 index 000000000000..9ca0ad39bc19 --- /dev/null +++ b/Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/bus/st,stm32-etzpc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STM32 Extended TrustZone protection controller + +description: | + The ETZPC configures TrustZone security in a SoC having bus masters and + devices with programmable-security attributes (securable resources). + +maintainers: + - Gatien Chevallier gatien.chevallier@foss.st.com + +properties: + compatible: + contains: + const: st,stm32-etzpc + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + ranges: true + + "#access-controller-cells": + const: 1 + description: + Contains the firewall ID associated to the peripheral. + +patternProperties: + "^.*@[0-9a-f]+$": + description: Peripherals + type: object + + additionalProperties: true + + required: + - access-controllers + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - "#access-controller-cells" + - ranges + +additionalProperties: false + +examples: + - | + // In this example, the usart2 device refers to rifsc as its access + // controller. + // Access rights are verified before creating devices. + + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp13-clks.h> + #include <dt-bindings/reset/stm32mp13-resets.h> + + etzpc: bus@5c007000 { + compatible = "st,stm32-etzpc"; + reg = <0x5c007000 0x400>; + #address-cells = <1>; + #size-cells = <1>; + #access-controller-cells = <1>; + ranges; + + usart2: serial@4c001000 { + compatible = "st,stm32h7-uart"; + reg = <0x4c001000 0x400>; + interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART2_K>; + resets = <&rcc USART2_R>; + wakeup-source; + dmas = <&dmamux1 43 0x400 0x5>, + <&dmamux1 44 0x400 0x1>; + dma-names = "rx", "tx"; + access-controllers = <&etzpc 17>; + }; + };
Introduce a STM32 firewall framework that offers to firewall consumers different firewall services such as the ability to check their access rights against their firewall controller(s).
The STM32 firewall framework offers a generic API for STM32 firewall controllers that is defined in their drivers to best fit the specificity of each firewall.
There are various types of firewalls: -Peripheral firewalls that filter accesses to peripherals -Memory firewalls that filter accesses to memories or memory regions -No type for undefined type of firewall
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V8: - Add missing dependency on OF for OF_DYNAMIC
Changes in V7: - Select OF_DYNAMIC when STM32_FIREWALL is set in order to use of_detach_node() in the firewall framework. Since the simple-bus pre-probe creates devices for all subnodes. This function is needed to detach particular nodes so that there's no match
Changes in V6: - Renamed access-controller to access-controllers
Changes in V5: - Rename feature-domain* to access-control* - Fix index out of range in stm32_firewall_get_firewall() - Add mising "select STM32_FIREWALL" in config ARCH_STM32 in arch/arm/mach-stm32/Kconfig
Changes in V4: - Fix documentation syntax - Put node in case of error in stm32_firewall_populate_bus() - Check firewall controller presence before using it in stm32_firewall_controller_register()
Changes in V2: - Support multiple entries for "feature-domains" property. Change stm32_firewall_get_firewall() to do so. - Better handle the device-tree parsing using phandle+args APIs and phandle iterator. - Remove "resource firewall" type - Rephrase STM32_FIREWALL description in the bus Kconfig and remove useless default value - Add missing EXPORT_SYMBOL_GPL - Remove useless stm32_firewall_get_id() API - Add a field for the name of the firewall entry in the stm32_firewall_controller structure - Minor fixes on some traces level (err -> debug) - Fix licenses to GPL-2.0-only - Fix stm32_firewall_get_firewall() description - Rephrase some sentences to better emphasize this is STM32-specific - Switch to list_for_each_entry() in stm32_firewall_controller_unregister() as we only expect one firewall controller instance per device. The loop just breaks when found - Do not register the firewall controller if it is already registered to the framework
MAINTAINERS | 5 + arch/arm/mach-stm32/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + drivers/bus/Kconfig | 10 + drivers/bus/Makefile | 1 + drivers/bus/stm32_firewall.c | 294 ++++++++++++++++++++++ drivers/bus/stm32_firewall.h | 83 ++++++ include/linux/bus/stm32_firewall_device.h | 141 +++++++++++ 8 files changed, 536 insertions(+) create mode 100644 drivers/bus/stm32_firewall.c create mode 100644 drivers/bus/stm32_firewall.h create mode 100644 include/linux/bus/stm32_firewall_device.h
diff --git a/MAINTAINERS b/MAINTAINERS index e2c6187a3ac8..774c7e1601d8 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -20430,6 +20430,11 @@ T: git git://linuxtv.org/media_tree.git F: Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml F: drivers/media/i2c/st-mipid02.c
+ST STM32 FIREWALL +M: Gatien Chevallier gatien.chevallier@foss.st.com +S: Maintained +F: drivers/bus/stm32_firewall.c + ST STM32 I2C/SMBUS DRIVER M: Pierre-Yves MORDRET pierre-yves.mordret@foss.st.com M: Alain Volmat alain.volmat@foss.st.com diff --git a/arch/arm/mach-stm32/Kconfig b/arch/arm/mach-stm32/Kconfig index 98145031586f..ae21a9f78f9c 100644 --- a/arch/arm/mach-stm32/Kconfig +++ b/arch/arm/mach-stm32/Kconfig @@ -12,6 +12,7 @@ menuconfig ARCH_STM32 select PINCTRL select RESET_CONTROLLER select STM32_EXTI + select STM32_FIREWALL help Support for STMicroelectronics STM32 processors.
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index 24335565bad5..13ed0a483617 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -305,6 +305,7 @@ config ARCH_STM32 select ARM_SMC_MBOX select ARM_SCMI_PROTOCOL select COMMON_CLK_SCMI + select STM32_FIREWALL help This enables support for ARMv8 based STMicroelectronics STM32 family, including: diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig index e6742998f372..7d47e0005cfe 100644 --- a/drivers/bus/Kconfig +++ b/drivers/bus/Kconfig @@ -163,6 +163,16 @@ config QCOM_SSC_BLOCK_BUS i2c/spi/uart controllers, a hexagon core, and a clock controller which provides clocks for the above.
+config STM32_FIREWALL + bool "STM32 Firewall framework" + depends on (ARCH_STM32 || COMPILE_TEST) && OF + select OF_DYNAMIC + help + Say y to enable STM32 firewall framework and its services. Firewall + controllers will be able to register to the framework. Access for + hardware resources linked to a firewall controller can be requested + through this STM32 framework. + config SUN50I_DE2_BUS bool "Allwinner A64 DE2 Bus Driver" default ARM64 diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile index d90eed189a65..fc0511450ec2 100644 --- a/drivers/bus/Makefile +++ b/drivers/bus/Makefile @@ -26,6 +26,7 @@ obj-$(CONFIG_OMAP_INTERCONNECT) += omap_l3_smx.o omap_l3_noc.o obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o obj-$(CONFIG_QCOM_EBI2) += qcom-ebi2.o obj-$(CONFIG_QCOM_SSC_BLOCK_BUS) += qcom-ssc-block-bus.o +obj-$(CONFIG_STM32_FIREWALL) += stm32_firewall.o obj-$(CONFIG_SUN50I_DE2_BUS) += sun50i-de2.o obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o obj-$(CONFIG_OF) += simple-pm-bus.o diff --git a/drivers/bus/stm32_firewall.c b/drivers/bus/stm32_firewall.c new file mode 100644 index 000000000000..decb79449047 --- /dev/null +++ b/drivers/bus/stm32_firewall.c @@ -0,0 +1,294 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2023, STMicroelectronics - All Rights Reserved + */ + +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/bus/stm32_firewall_device.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/types.h> +#include <linux/slab.h> + +#include "stm32_firewall.h" + +/* Corresponds to STM32_FIREWALL_MAX_EXTRA_ARGS + firewall ID */ +#define STM32_FIREWALL_MAX_ARGS (STM32_FIREWALL_MAX_EXTRA_ARGS + 1) + +static LIST_HEAD(firewall_controller_list); +static DEFINE_MUTEX(firewall_controller_list_lock); + +/* Firewall device API */ + +int stm32_firewall_get_firewall(struct device_node *np, struct stm32_firewall *firewall, + unsigned int nb_firewall) +{ + struct stm32_firewall_controller *ctrl; + struct of_phandle_iterator it; + unsigned int i, j = 0; + int err; + + if (!firewall || !nb_firewall) + return -EINVAL; + + /* Parse property with phandle parsed out */ + of_for_each_phandle(&it, err, np, "access-controllers", "#access-controller-cells", 0) { + struct of_phandle_args provider_args; + struct device_node *provider = it.node; + const char *fw_entry; + bool match = false; + + if (err) { + pr_err("Unable to get access-controllers property for node %s\n, err: %d", + np->full_name, err); + of_node_put(provider); + return err; + } + + if (j > nb_firewall) { + pr_err("Too many firewall controllers"); + of_node_put(provider); + return -EINVAL; + } + + provider_args.args_count = of_phandle_iterator_args(&it, provider_args.args, + STM32_FIREWALL_MAX_ARGS); + + /* Check if the parsed phandle corresponds to a registered firewall controller */ + mutex_lock(&firewall_controller_list_lock); + list_for_each_entry(ctrl, &firewall_controller_list, entry) { + if (ctrl->dev->of_node->phandle == it.phandle) { + match = true; + firewall[j].firewall_ctrl = ctrl; + break; + } + } + mutex_unlock(&firewall_controller_list_lock); + + if (!match) { + firewall[j].firewall_ctrl = NULL; + pr_err("No firewall controller registered for %s\n", np->full_name); + of_node_put(provider); + return -ENODEV; + } + + err = of_property_read_string_index(np, "access-controller-names", j, &fw_entry); + if (err == 0) + firewall[j].entry = fw_entry; + + /* Handle the case when there are no arguments given along with the phandle */ + if (provider_args.args_count < 0 || + provider_args.args_count > STM32_FIREWALL_MAX_ARGS) { + of_node_put(provider); + return -EINVAL; + } else if (provider_args.args_count == 0) { + firewall[j].extra_args_size = 0; + firewall[j].firewall_id = U32_MAX; + j++; + continue; + } + + /* The firewall ID is always the first argument */ + firewall[j].firewall_id = provider_args.args[0]; + + /* Extra args start at the second argument */ + for (i = 0; i < provider_args.args_count - 1; i++) + firewall[j].extra_args[i] = provider_args.args[i + 1]; + + /* Remove the firewall ID arg that is not an extra argument */ + firewall[j].extra_args_size = provider_args.args_count - 1; + + j++; + } + + return 0; +} +EXPORT_SYMBOL_GPL(stm32_firewall_get_firewall); + +int stm32_firewall_grant_access(struct stm32_firewall *firewall) +{ + struct stm32_firewall_controller *firewall_controller; + + if (!firewall || firewall->firewall_id == U32_MAX) + return -EINVAL; + + firewall_controller = firewall->firewall_ctrl; + + if (!firewall_controller) + return -ENODEV; + + return firewall_controller->grant_access(firewall_controller, firewall->firewall_id); +} +EXPORT_SYMBOL_GPL(stm32_firewall_grant_access); + +int stm32_firewall_grant_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id) +{ + struct stm32_firewall_controller *firewall_controller; + + if (!firewall || subsystem_id == U32_MAX || firewall->firewall_id == U32_MAX) + return -EINVAL; + + firewall_controller = firewall->firewall_ctrl; + + if (!firewall_controller) + return -ENODEV; + + return firewall_controller->grant_access(firewall_controller, subsystem_id); +} +EXPORT_SYMBOL_GPL(stm32_firewall_grant_access_by_id); + +void stm32_firewall_release_access(struct stm32_firewall *firewall) +{ + struct stm32_firewall_controller *firewall_controller; + + if (!firewall || firewall->firewall_id == U32_MAX) { + pr_debug("Incorrect arguments when releasing a firewall access\n"); + return; + } + + firewall_controller = firewall->firewall_ctrl; + + if (!firewall_controller) { + pr_debug("No firewall controller to release\n"); + return; + } + + firewall_controller->release_access(firewall_controller, firewall->firewall_id); +} +EXPORT_SYMBOL_GPL(stm32_firewall_release_access); + +void stm32_firewall_release_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id) +{ + struct stm32_firewall_controller *firewall_controller; + + if (!firewall || subsystem_id == U32_MAX || firewall->firewall_id == U32_MAX) { + pr_debug("Incorrect arguments when releasing a firewall access"); + return; + } + + firewall_controller = firewall->firewall_ctrl; + + if (!firewall_controller) { + pr_debug("No firewall controller to release"); + return; + } + + firewall_controller->release_access(firewall_controller, subsystem_id); +} +EXPORT_SYMBOL_GPL(stm32_firewall_release_access_by_id); + +/* Firewall controller API */ + +int stm32_firewall_controller_register(struct stm32_firewall_controller *firewall_controller) +{ + struct stm32_firewall_controller *ctrl; + + if (!firewall_controller) + return -ENODEV; + + pr_info("Registering %s firewall controller\n", firewall_controller->name); + + mutex_lock(&firewall_controller_list_lock); + list_for_each_entry(ctrl, &firewall_controller_list, entry) { + if (ctrl == firewall_controller) { + pr_debug("%s firewall controller already registered\n", + firewall_controller->name); + mutex_unlock(&firewall_controller_list_lock); + return 0; + } + } + list_add_tail(&firewall_controller->entry, &firewall_controller_list); + mutex_unlock(&firewall_controller_list_lock); + + return 0; +} +EXPORT_SYMBOL_GPL(stm32_firewall_controller_register); + +void stm32_firewall_controller_unregister(struct stm32_firewall_controller *firewall_controller) +{ + struct stm32_firewall_controller *ctrl; + bool controller_removed = false; + + if (!firewall_controller) { + pr_debug("Null reference while unregistering firewall controller\n"); + return; + } + + mutex_lock(&firewall_controller_list_lock); + list_for_each_entry(ctrl, &firewall_controller_list, entry) { + if (ctrl == firewall_controller) { + controller_removed = true; + list_del_init(&ctrl->entry); + break; + } + } + mutex_unlock(&firewall_controller_list_lock); + + if (!controller_removed) + pr_debug("There was no firewall controller named %s to unregister\n", + firewall_controller->name); +} +EXPORT_SYMBOL_GPL(stm32_firewall_controller_unregister); + +int stm32_firewall_populate_bus(struct stm32_firewall_controller *firewall_controller) +{ + struct stm32_firewall *firewalls; + struct device_node *child; + struct device *parent; + unsigned int i; + int len; + int err; + + parent = firewall_controller->dev; + + dev_dbg(parent, "Populating %s system bus\n", dev_name(firewall_controller->dev)); + + for_each_available_child_of_node(dev_of_node(parent), child) { + /* The access-controllers property is mandatory for firewall bus devices */ + len = of_count_phandle_with_args(child, "access-controllers", + "#access-controller-cells"); + if (len <= 0) { + of_node_put(child); + return -EINVAL; + } + + firewalls = kcalloc(len, sizeof(*firewalls), GFP_KERNEL); + if (!firewalls) { + of_node_put(child); + return -ENOMEM; + } + + err = stm32_firewall_get_firewall(child, firewalls, (unsigned int)len); + if (err) { + kfree(firewalls); + of_node_put(child); + return err; + } + + for (i = 0; i < len; i++) { + if (firewall_controller->grant_access(firewall_controller, + firewalls[i].firewall_id)) { + /* + * Peripheral access not allowed or not defined. + * Mark the node as populated so platform bus won't probe it + */ + of_detach_node(child); + dev_err(parent, "%s: Device driver will not be probed\n", + child->full_name); + } + } + + kfree(firewalls); + } + + return 0; +} +EXPORT_SYMBOL_GPL(stm32_firewall_populate_bus); diff --git a/drivers/bus/stm32_firewall.h b/drivers/bus/stm32_firewall.h new file mode 100644 index 000000000000..e5fac85fe346 --- /dev/null +++ b/drivers/bus/stm32_firewall.h @@ -0,0 +1,83 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Copyright (C) 2023, STMicroelectronics - All Rights Reserved + */ + +#ifndef _STM32_FIREWALL_H +#define _STM32_FIREWALL_H + +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/types.h> + +/** + * STM32_PERIPHERAL_FIREWALL: This type of firewall protects peripherals + * STM32_MEMORY_FIREWALL: This type of firewall protects memories/subsets of memory + * zones + * STM32_NOTYPE_FIREWALL: Undefined firewall type + */ + +#define STM32_PERIPHERAL_FIREWALL BIT(1) +#define STM32_MEMORY_FIREWALL BIT(2) +#define STM32_NOTYPE_FIREWALL BIT(3) + +/** + * struct stm32_firewall_controller - Information on firewall controller supplying services + * + * @name: Name of the firewall controller + * @dev: Device reference of the firewall controller + * @mmio: Base address of the firewall controller + * @entry: List entry of the firewall controller list + * @type: Type of firewall + * @max_entries: Number of entries covered by the firewall + * @grant_access: Callback used to grant access for a device access against a + * firewall controller + * @release_access: Callback used to release resources taken by a device when access was + * granted + * @grant_memory_range_access: Callback used to grant access for a device to a given memory region + */ +struct stm32_firewall_controller { + const char *name; + struct device *dev; + void __iomem *mmio; + struct list_head entry; + unsigned int type; + unsigned int max_entries; + + int (*grant_access)(struct stm32_firewall_controller *ctrl, u32 id); + void (*release_access)(struct stm32_firewall_controller *ctrl, u32 id); + int (*grant_memory_range_access)(struct stm32_firewall_controller *ctrl, phys_addr_t paddr, + size_t size); +}; + +/** + * stm32_firewall_controller_register - Register a firewall controller to the STM32 firewall + * framework + * @firewall_controller: Firewall controller to register + * + * Returns 0 in case of success or -ENODEV if no controller was given. + */ +int stm32_firewall_controller_register(struct stm32_firewall_controller *firewall_controller); + +/** + * stm32_firewall_controller_unregister - Unregister a firewall controller from the STM32 + * firewall framework + * @firewall_controller: Firewall controller to unregister + */ +void stm32_firewall_controller_unregister(struct stm32_firewall_controller *firewall_controller); + +/** + * stm32_firewall_populate_bus - Populate device tree nodes that have a correct firewall + * configuration. This is used at boot-time only, as a sanity check + * between device tree and firewalls hardware configurations to + * prevent a kernel crash when a device driver is not granted access + * + * @firewall_controller: Firewall controller which nodes will be populated or not + * + * Returns 0 in case of success or appropriate errno code if error occurred. + */ +int stm32_firewall_populate_bus(struct stm32_firewall_controller *firewall_controller); + +#endif /* _STM32_FIREWALL_H */ diff --git a/include/linux/bus/stm32_firewall_device.h b/include/linux/bus/stm32_firewall_device.h new file mode 100644 index 000000000000..bbbee0b24ea8 --- /dev/null +++ b/include/linux/bus/stm32_firewall_device.h @@ -0,0 +1,141 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Copyright (C) 2023, STMicroelectronics - All Rights Reserved + */ + +#ifndef STM32_FIREWALL_DEVICE_H +#define STM32_FIREWALL_DEVICE_H + +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/types.h> + +#define STM32_FIREWALL_MAX_EXTRA_ARGS 5 + +/* Opaque reference to stm32_firewall_controller */ +struct stm32_firewall_controller; + +/** + * struct stm32_firewall - Information on a device's firewall. Each device can have more than one + * firewall. + * + * @firewall_ctrl: Pointer referencing a firewall controller of the device. It is + * opaque so a device cannot manipulate the controller's ops or access + * the controller's data + * @extra_args: Extra arguments that are implementation dependent + * @entry: Name of the firewall entry + * @extra_args_size: Number of extra arguments + * @firewall_id: Firewall ID associated the device for this firewall controller + */ +struct stm32_firewall { + struct stm32_firewall_controller *firewall_ctrl; + u32 extra_args[STM32_FIREWALL_MAX_EXTRA_ARGS]; + const char *entry; + size_t extra_args_size; + u32 firewall_id; +}; + +#if IS_ENABLED(CONFIG_STM32_FIREWALL) +/** + * stm32_firewall_get_firewall - Get the firewall(s) associated to given device. + * The firewall controller reference is always the first argument + * of each of the access-controller property entries. + * The firewall ID is always the second argument of each of the + * access-controller property entries. + * If there's no argument linked to the phandle, then the firewall ID + * field is set to U32_MAX, which is an invalid ID. + * + * @np: Device node to parse + * @firewall: Array of firewall references + * @nb_firewall: Number of firewall references to get. Must be at least 1. + * + * Returns 0 on success, -ENODEV if there's no match with a firewall controller or appropriate errno + * code if error occurred. + */ +int stm32_firewall_get_firewall(struct device_node *np, struct stm32_firewall *firewall, + unsigned int nb_firewall); + +/** + * stm32_firewall_grant_access - Request firewall access rights and grant access. + * + * @firewall: Firewall reference containing the ID to check against its firewall + * controller + * + * Returns 0 if access is granted, -EACCES if access is denied, -ENODEV if firewall is null or + * appropriate errno code if error occurred + */ +int stm32_firewall_grant_access(struct stm32_firewall *firewall); + +/** + * stm32_firewall_release_access - Release access granted from a call to + * stm32_firewall_grant_access(). + * + * @firewall: Firewall reference containing the ID to check against its firewall + * controller + */ +void stm32_firewall_release_access(struct stm32_firewall *firewall); + +/** + * stm32_firewall_grant_access_by_id - Request firewall access rights of a given device + * based on a specific firewall ID + * + * Warnings: + * There is no way to ensure that the given ID will correspond to the firewall referenced in the + * device node if the ID did not come from stm32_firewall_get_firewall(). In that case, this + * function must be used with caution. + * This function should be used for subsystem resources that do not have the same firewall ID + * as their parent. + * U32_MAX is an invalid ID. + * + * @firewall: Firewall reference containing the firewall controller + * @subsystem_id: Firewall ID of the subsystem resource + * + * Returns 0 if access is granted, -EACCES if access is denied, -ENODEV if firewall is null or + * appropriate errno code if error occurred + */ +int stm32_firewall_grant_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id); + +/** + * stm32_firewall_release_access_by_id - Release access granted from a call to + * stm32_firewall_grant_access_by_id(). + * + * Warnings: + * There is no way to ensure that the given ID will correspond to the firewall referenced in the + * device node if the ID did not come from stm32_firewall_get_firewall(). In that case, this + * function must be used with caution. + * This function should be used for subsystem resources that do not have the same firewall ID + * as their parent. + * U32_MAX is an invalid ID. + * + * @firewall: Firewall reference containing the firewall controller + * @subsystem_id: Firewall ID of the subsystem resource + */ +void stm32_firewall_release_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id); + +#else /* CONFIG_STM32_FIREWALL */ + +int stm32_firewall_get_firewall(struct device_node *np, struct stm32_firewall *firewall) +{ + return -ENODEV; +} + +int stm32_firewall_grant_access(struct stm32_firewall *firewall) +{ + return -ENODEV; +} + +void stm32_firewall_release_access(struct stm32_firewall *firewall) +{ +} + +int stm32_firewall_grant_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id) +{ + return -ENODEV; +} + +void stm32_firewall_release_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id) +{ +} + +#endif /* CONFIG_STM32_FIREWALL */ +#endif /* STM32_FIREWALL_DEVICE_H */
Allows tracking dependencies between devices and their access controller.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V6: - Renamed access-controller to access-controllers
Changes in V5: - Rename feature-domain* to access-control*
Patch not present in V1
drivers/of/property.c | 2 ++ 1 file changed, 2 insertions(+)
diff --git a/drivers/of/property.c b/drivers/of/property.c index afdaefbd03f6..7f737eac91b2 100644 --- a/drivers/of/property.c +++ b/drivers/of/property.c @@ -1268,6 +1268,7 @@ DEFINE_SIMPLE_PROP(leds, "leds", NULL) DEFINE_SIMPLE_PROP(backlight, "backlight", NULL) DEFINE_SIMPLE_PROP(panel, "panel", NULL) DEFINE_SIMPLE_PROP(msi_parent, "msi-parent", "#msi-cells") +DEFINE_SIMPLE_PROP(access_controllers, "access-controllers", "#access-controller-cells") DEFINE_SUFFIX_PROP(regulators, "-supply", NULL) DEFINE_SUFFIX_PROP(gpio, "-gpio", "#gpio-cells")
@@ -1363,6 +1364,7 @@ static const struct supplier_bindings of_supplier_bindings[] = { { .parse_prop = parse_regulators, }, { .parse_prop = parse_gpio, }, { .parse_prop = parse_gpios, }, + { .parse_prop = parse_access_controllers, }, {} };
On Tue, 12 Dec 2023 16:23:49 +0100, Gatien Chevallier wrote:
Acked-by: Rob Herring robh@kernel.org
RIFSC is a peripheral firewall controller that filter accesses based on Arm TrustZone secure state, Arm CPU privilege execution level and Compartment IDentification of the STM32 SoC subsystems.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V4: - Fix incorrect use of __set_bit() in - stm32_rif_acquire_semaphore()
Changes in V2: - Add controller name - Driver is now a module_platform_driver - Use error code returned by stm32_firewall_populate_bus() - Fix license
MAINTAINERS | 1 + drivers/bus/Makefile | 2 +- drivers/bus/stm32_rifsc.c | 252 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 254 insertions(+), 1 deletion(-) create mode 100644 drivers/bus/stm32_rifsc.c
diff --git a/MAINTAINERS b/MAINTAINERS index 774c7e1601d8..a1152438b52d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -20434,6 +20434,7 @@ ST STM32 FIREWALL M: Gatien Chevallier gatien.chevallier@foss.st.com S: Maintained F: drivers/bus/stm32_firewall.c +F: drivers/bus/stm32_rifsc.c
ST STM32 I2C/SMBUS DRIVER M: Pierre-Yves MORDRET pierre-yves.mordret@foss.st.com diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile index fc0511450ec2..e50d18e1d141 100644 --- a/drivers/bus/Makefile +++ b/drivers/bus/Makefile @@ -26,7 +26,7 @@ obj-$(CONFIG_OMAP_INTERCONNECT) += omap_l3_smx.o omap_l3_noc.o obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o obj-$(CONFIG_QCOM_EBI2) += qcom-ebi2.o obj-$(CONFIG_QCOM_SSC_BLOCK_BUS) += qcom-ssc-block-bus.o -obj-$(CONFIG_STM32_FIREWALL) += stm32_firewall.o +obj-$(CONFIG_STM32_FIREWALL) += stm32_firewall.o stm32_rifsc.o obj-$(CONFIG_SUN50I_DE2_BUS) += sun50i-de2.o obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o obj-$(CONFIG_OF) += simple-pm-bus.o diff --git a/drivers/bus/stm32_rifsc.c b/drivers/bus/stm32_rifsc.c new file mode 100644 index 000000000000..4cf1b60014b7 --- /dev/null +++ b/drivers/bus/stm32_rifsc.c @@ -0,0 +1,252 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2023, STMicroelectronics - All Rights Reserved + */ + +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/types.h> + +#include "stm32_firewall.h" + +/* + * RIFSC offset register + */ +#define RIFSC_RISC_SECCFGR0 0x10 +#define RIFSC_RISC_PRIVCFGR0 0x30 +#define RIFSC_RISC_PER0_CIDCFGR 0x100 +#define RIFSC_RISC_PER0_SEMCR 0x104 +#define RIFSC_RISC_HWCFGR2 0xFEC + +/* + * SEMCR register + */ +#define SEMCR_MUTEX BIT(0) + +/* + * HWCFGR2 register + */ +#define HWCFGR2_CONF1_MASK GENMASK(15, 0) +#define HWCFGR2_CONF2_MASK GENMASK(23, 16) +#define HWCFGR2_CONF3_MASK GENMASK(31, 24) + +/* + * RIFSC miscellaneous + */ +#define RIFSC_RISC_CFEN_MASK BIT(0) +#define RIFSC_RISC_SEM_EN_MASK BIT(1) +#define RIFSC_RISC_SCID_MASK GENMASK(6, 4) +#define RIFSC_RISC_SEML_SHIFT 16 +#define RIFSC_RISC_SEMWL_MASK GENMASK(23, 16) +#define RIFSC_RISC_PER_ID_MASK GENMASK(31, 24) + +#define RIFSC_RISC_PERx_CID_MASK (RIFSC_RISC_CFEN_MASK | \ + RIFSC_RISC_SEM_EN_MASK | \ + RIFSC_RISC_SCID_MASK | \ + RIFSC_RISC_SEMWL_MASK) + +#define IDS_PER_RISC_SEC_PRIV_REGS 32 + +/* RIF miscellaneous */ +/* + * CIDCFGR register fields + */ +#define CIDCFGR_CFEN BIT(0) +#define CIDCFGR_SEMEN BIT(1) +#define CIDCFGR_SEMWL(x) BIT(RIFSC_RISC_SEML_SHIFT + (x)) + +#define SEMWL_SHIFT 16 + +/* Compartiment IDs */ +#define RIF_CID0 0x0 +#define RIF_CID1 0x1 + +static bool stm32_rifsc_is_semaphore_available(void __iomem *addr) +{ + return !(readl(addr) & SEMCR_MUTEX); +} + +static int stm32_rif_acquire_semaphore(struct stm32_firewall_controller *stm32_firewall_controller, + int id) +{ + void __iomem *addr = stm32_firewall_controller->mmio + RIFSC_RISC_PER0_SEMCR + 0x8 * id; + + writel(SEMCR_MUTEX, addr); + + /* Check that CID1 has the semaphore */ + if (stm32_rifsc_is_semaphore_available(addr) || + FIELD_GET(RIFSC_RISC_SCID_MASK, readl(addr)) != RIF_CID1) + return -EACCES; + + return 0; +} + +static void stm32_rif_release_semaphore(struct stm32_firewall_controller *stm32_firewall_controller, + int id) +{ + void __iomem *addr = stm32_firewall_controller->mmio + RIFSC_RISC_PER0_SEMCR + 0x8 * id; + + if (stm32_rifsc_is_semaphore_available(addr)) + return; + + writel(SEMCR_MUTEX, addr); + + /* Ok if another compartment takes the semaphore before the check */ + WARN_ON(!stm32_rifsc_is_semaphore_available(addr) && + FIELD_GET(RIFSC_RISC_SCID_MASK, readl(addr)) == RIF_CID1); +} + +static int stm32_rifsc_grant_access(struct stm32_firewall_controller *ctrl, u32 firewall_id) +{ + struct stm32_firewall_controller *rifsc_controller = ctrl; + u32 reg_offset, reg_id, sec_reg_value, cid_reg_value; + int rc; + + if (firewall_id >= rifsc_controller->max_entries) { + dev_err(rifsc_controller->dev, "Invalid sys bus ID %u", firewall_id); + return -EINVAL; + } + + /* + * RIFSC_RISC_PRIVCFGRx and RIFSC_RISC_SECCFGRx both handle configuration access for + * 32 peripherals. On the other hand, there is one _RIFSC_RISC_PERx_CIDCFGR register + * per peripheral + */ + reg_id = firewall_id / IDS_PER_RISC_SEC_PRIV_REGS; + reg_offset = firewall_id % IDS_PER_RISC_SEC_PRIV_REGS; + sec_reg_value = readl(rifsc_controller->mmio + RIFSC_RISC_SECCFGR0 + 0x4 * reg_id); + cid_reg_value = readl(rifsc_controller->mmio + RIFSC_RISC_PER0_CIDCFGR + 0x8 * firewall_id); + + /* First check conditions for semaphore mode, which doesn't take into account static CID. */ + if ((cid_reg_value & CIDCFGR_SEMEN) && (cid_reg_value & CIDCFGR_CFEN)) { + if (cid_reg_value & BIT(RIF_CID1 + SEMWL_SHIFT)) { + /* Static CID is irrelevant if semaphore mode */ + goto skip_cid_check; + } else { + dev_dbg(rifsc_controller->dev, + "Invalid bus semaphore configuration: index %d\n", firewall_id); + return -EACCES; + } + } + + /* + * Skip CID check if CID filtering isn't enabled or filtering is enabled on CID0, which + * corresponds to whatever CID. + */ + if (!(cid_reg_value & CIDCFGR_CFEN) || + FIELD_GET(RIFSC_RISC_SCID_MASK, cid_reg_value) == RIF_CID0) + goto skip_cid_check; + + /* Coherency check with the CID configuration */ + if (FIELD_GET(RIFSC_RISC_SCID_MASK, cid_reg_value) != RIF_CID1) { + dev_dbg(rifsc_controller->dev, "Invalid CID configuration for peripheral: %d\n", + firewall_id); + return -EACCES; + } + +skip_cid_check: + /* Check security configuration */ + if (sec_reg_value & BIT(reg_offset)) { + dev_dbg(rifsc_controller->dev, + "Invalid security configuration for peripheral: %d\n", firewall_id); + return -EACCES; + } + + /* + * If the peripheral is in semaphore mode, take the semaphore so that + * the CID1 has the ownership. + */ + if ((cid_reg_value & CIDCFGR_SEMEN) && (cid_reg_value & CIDCFGR_CFEN)) { + rc = stm32_rif_acquire_semaphore(rifsc_controller, firewall_id); + if (rc) { + dev_err(rifsc_controller->dev, + "Couldn't acquire semaphore for peripheral: %d\n", firewall_id); + return rc; + } + } + + return 0; +} + +static void stm32_rifsc_release_access(struct stm32_firewall_controller *ctrl, u32 firewall_id) +{ + stm32_rif_release_semaphore(ctrl, firewall_id); +} + +static int stm32_rifsc_probe(struct platform_device *pdev) +{ + struct stm32_firewall_controller *rifsc_controller; + struct device_node *np = pdev->dev.of_node; + u32 nb_risup, nb_rimu, nb_risal; + struct resource *res; + void __iomem *mmio; + int rc; + + rifsc_controller = devm_kzalloc(&pdev->dev, sizeof(*rifsc_controller), GFP_KERNEL); + if (!rifsc_controller) + return -ENOMEM; + + mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res); + if (IS_ERR(mmio)) + return PTR_ERR(mmio); + + rifsc_controller->dev = &pdev->dev; + rifsc_controller->mmio = mmio; + rifsc_controller->name = dev_driver_string(rifsc_controller->dev); + rifsc_controller->type = STM32_PERIPHERAL_FIREWALL | STM32_MEMORY_FIREWALL; + rifsc_controller->grant_access = stm32_rifsc_grant_access; + rifsc_controller->release_access = stm32_rifsc_release_access; + + /* Get number of RIFSC entries*/ + nb_risup = readl(rifsc_controller->mmio + RIFSC_RISC_HWCFGR2) & HWCFGR2_CONF1_MASK; + nb_rimu = readl(rifsc_controller->mmio + RIFSC_RISC_HWCFGR2) & HWCFGR2_CONF2_MASK; + nb_risal = readl(rifsc_controller->mmio + RIFSC_RISC_HWCFGR2) & HWCFGR2_CONF3_MASK; + rifsc_controller->max_entries = nb_risup + nb_rimu + nb_risal; + + platform_set_drvdata(pdev, rifsc_controller); + + rc = stm32_firewall_controller_register(rifsc_controller); + if (rc) { + dev_err(rifsc_controller->dev, "Couldn't register as a firewall controller: %d", + rc); + return rc; + } + + rc = stm32_firewall_populate_bus(rifsc_controller); + if (rc) { + dev_err(rifsc_controller->dev, "Couldn't populate RIFSC bus: %d", + rc); + return rc; + } + + /* Populate all allowed nodes */ + return of_platform_populate(np, NULL, NULL, &pdev->dev); +} + +static const struct of_device_id stm32_rifsc_of_match[] = { + { .compatible = "st,stm32mp25-rifsc" }, + {} +}; +MODULE_DEVICE_TABLE(of, stm32_rifsc_of_match); + +static struct platform_driver stm32_rifsc_driver = { + .probe = stm32_rifsc_probe, + .driver = { + .name = "stm32-rifsc", + .of_match_table = stm32_rifsc_of_match, + }, +}; +module_platform_driver(stm32_rifsc_driver); + +MODULE_AUTHOR("Gatien Chevallier gatien.chevallier@foss.st.com"); +MODULE_DESCRIPTION("STMicroelectronics RIFSC driver"); +MODULE_LICENSE("GPL");
RIFSC is a firewall controller. Add "st,stm32mp25-rifsc" compatible and reference RIFSC as an access-control-provider. Keep "simple-bus" compatible backward compatibility.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V8: - Keep "simple-bus" compatible
Changes in V6: - Renamed access-controller to access-controllers - Removal of access-control-provider property
Changes in V5: - Renamed feature-domain* to access-control*
Changes in V2: - Fix rifsc node name - Move the "ranges" property under the "feature-domains" one
arch/arm64/boot/dts/st/stm32mp251.dtsi | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/st/stm32mp251.dtsi b/arch/arm64/boot/dts/st/stm32mp251.dtsi index 124403f5f1f4..3b0d6dced81f 100644 --- a/arch/arm64/boot/dts/st/stm32mp251.dtsi +++ b/arch/arm64/boot/dts/st/stm32mp251.dtsi @@ -111,11 +111,12 @@ soc@0 { interrupt-parent = <&intc>; ranges = <0x0 0x0 0x0 0x80000000>;
- rifsc: rifsc-bus@42080000 { - compatible = "simple-bus"; + rifsc: bus@42080000 { + compatible = "st,stm32mp25-rifsc", "simple-bus"; reg = <0x42080000 0x1000>; #address-cells = <1>; #size-cells = <1>; + #access-controller-cells = <1>; ranges;
usart2: serial@400e0000 { @@ -123,6 +124,7 @@ usart2: serial@400e0000 { reg = <0x400e0000 0x400>; interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ck_flexgen_08>; + access-controllers = <&rifsc 32>; status = "disabled"; };
@@ -136,6 +138,7 @@ sdmmc1: mmc@48220000 { cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <120000000>; + access-controllers = <&rifsc 92>; status = "disabled"; }; };
ETZPC is a peripheral and memory firewall controller that filter accesses based on Arm TrustZone secure state and Arm CPU privilege execution level. It handles MCU isolation as well.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V2: - Add controller name - Driver is now a module_platform_driver - Use error code returned by stm32_firewall_populate_bus() - Fix license
MAINTAINERS | 1 + drivers/bus/Makefile | 2 +- drivers/bus/stm32_etzpc.c | 141 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 143 insertions(+), 1 deletion(-) create mode 100644 drivers/bus/stm32_etzpc.c
diff --git a/MAINTAINERS b/MAINTAINERS index a1152438b52d..b83b471c8b73 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -20433,6 +20433,7 @@ F: drivers/media/i2c/st-mipid02.c ST STM32 FIREWALL M: Gatien Chevallier gatien.chevallier@foss.st.com S: Maintained +F: drivers/bus/stm32_etzpc.c F: drivers/bus/stm32_firewall.c F: drivers/bus/stm32_rifsc.c
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile index e50d18e1d141..cddd4984d6af 100644 --- a/drivers/bus/Makefile +++ b/drivers/bus/Makefile @@ -26,7 +26,7 @@ obj-$(CONFIG_OMAP_INTERCONNECT) += omap_l3_smx.o omap_l3_noc.o obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o obj-$(CONFIG_QCOM_EBI2) += qcom-ebi2.o obj-$(CONFIG_QCOM_SSC_BLOCK_BUS) += qcom-ssc-block-bus.o -obj-$(CONFIG_STM32_FIREWALL) += stm32_firewall.o stm32_rifsc.o +obj-$(CONFIG_STM32_FIREWALL) += stm32_firewall.o stm32_rifsc.o stm32_etzpc.o obj-$(CONFIG_SUN50I_DE2_BUS) += sun50i-de2.o obj-$(CONFIG_SUNXI_RSB) += sunxi-rsb.o obj-$(CONFIG_OF) += simple-pm-bus.o diff --git a/drivers/bus/stm32_etzpc.c b/drivers/bus/stm32_etzpc.c new file mode 100644 index 000000000000..7fc0f16960be --- /dev/null +++ b/drivers/bus/stm32_etzpc.c @@ -0,0 +1,141 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2023, STMicroelectronics - All Rights Reserved + */ + +#include <linux/bitfield.h> +#include <linux/bits.h> +#include <linux/device.h> +#include <linux/err.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <linux/types.h> + +#include "stm32_firewall.h" + +/* + * ETZPC registers + */ +#define ETZPC_DECPROT 0x10 +#define ETZPC_HWCFGR 0x3F0 + +/* + * HWCFGR register + */ +#define ETZPC_HWCFGR_NUM_TZMA GENMASK(7, 0) +#define ETZPC_HWCFGR_NUM_PER_SEC GENMASK(15, 8) +#define ETZPC_HWCFGR_NUM_AHB_SEC GENMASK(23, 16) +#define ETZPC_HWCFGR_CHUNKS1N4 GENMASK(31, 24) + +/* + * ETZPC miscellaneous + */ +#define ETZPC_PROT_MASK GENMASK(1, 0) +#define ETZPC_PROT_A7NS 0x3 +#define ETZPC_DECPROT_SHIFT 1 + +#define IDS_PER_DECPROT_REGS 16 + +static int stm32_etzpc_grant_access(struct stm32_firewall_controller *ctrl, u32 firewall_id) +{ + u32 offset, reg_offset, sec_val; + + if (firewall_id >= ctrl->max_entries) { + dev_err(ctrl->dev, "Invalid sys bus ID %u", firewall_id); + return -EINVAL; + } + + /* Check access configuration, 16 peripherals per register */ + reg_offset = ETZPC_DECPROT + 0x4 * (firewall_id / IDS_PER_DECPROT_REGS); + offset = (firewall_id % IDS_PER_DECPROT_REGS) << ETZPC_DECPROT_SHIFT; + + /* Verify peripheral is non-secure and attributed to cortex A7 */ + sec_val = (readl(ctrl->mmio + reg_offset) >> offset) & ETZPC_PROT_MASK; + if (sec_val != ETZPC_PROT_A7NS) { + dev_dbg(ctrl->dev, "Invalid bus configuration: reg_offset %#x, value %d\n", + reg_offset, sec_val); + return -EACCES; + } + + return 0; +} + +static void stm32_etzpc_release_access(struct stm32_firewall_controller *ctrl __maybe_unused, + u32 firewall_id __maybe_unused) +{ +} + +static int stm32_etzpc_probe(struct platform_device *pdev) +{ + struct stm32_firewall_controller *etzpc_controller; + struct device_node *np = pdev->dev.of_node; + u32 nb_per, nb_master; + struct resource *res; + void __iomem *mmio; + int rc; + + etzpc_controller = devm_kzalloc(&pdev->dev, sizeof(*etzpc_controller), GFP_KERNEL); + if (!etzpc_controller) + return -ENOMEM; + + mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res); + if (IS_ERR(mmio)) + return PTR_ERR(mmio); + + etzpc_controller->dev = &pdev->dev; + etzpc_controller->mmio = mmio; + etzpc_controller->name = dev_driver_string(etzpc_controller->dev); + etzpc_controller->type = STM32_PERIPHERAL_FIREWALL | STM32_MEMORY_FIREWALL; + etzpc_controller->grant_access = stm32_etzpc_grant_access; + etzpc_controller->release_access = stm32_etzpc_release_access; + + /* Get number of etzpc entries*/ + nb_per = FIELD_GET(ETZPC_HWCFGR_NUM_PER_SEC, + readl(etzpc_controller->mmio + ETZPC_HWCFGR)); + nb_master = FIELD_GET(ETZPC_HWCFGR_NUM_AHB_SEC, + readl(etzpc_controller->mmio + ETZPC_HWCFGR)); + etzpc_controller->max_entries = nb_per + nb_master; + + platform_set_drvdata(pdev, etzpc_controller); + + rc = stm32_firewall_controller_register(etzpc_controller); + if (rc) { + dev_err(etzpc_controller->dev, "Couldn't register as a firewall controller: %d", + rc); + return rc; + } + + rc = stm32_firewall_populate_bus(etzpc_controller); + if (rc) { + dev_err(etzpc_controller->dev, "Couldn't populate ETZPC bus: %d", + rc); + return rc; + } + + /* Populate all allowed nodes */ + return of_platform_populate(np, NULL, NULL, &pdev->dev); +} + +static const struct of_device_id stm32_etzpc_of_match[] = { + { .compatible = "st,stm32-etzpc" }, + {} +}; +MODULE_DEVICE_TABLE(of, stm32_etzpc_of_match); + +static struct platform_driver stm32_etzpc_driver = { + .probe = stm32_etzpc_probe, + .driver = { + .name = "stm32-etzpc", + .of_match_table = stm32_etzpc_of_match, + }, +}; +module_platform_driver(stm32_etzpc_driver); + +MODULE_AUTHOR("Gatien Chevallier gatien.chevallier@foss.st.com"); +MODULE_DESCRIPTION("STMicroelectronics ETZPC driver"); +MODULE_LICENSE("GPL");
ETZPC is a firewall controller. Put all peripherals filtered by the ETZPC as ETZPC subnodes and keep the "simple-bus" compatible for backward compatibility.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V8: - Keep simple-bus compatible
Changes in V7: - Remove access-controllers reference in this patch
Changes in V6: - Renamed access-controller to access-controllers - Removal of access-control-provider property
Changes in V5: - Renamed feature-domain* to access-control*
arch/arm/boot/dts/st/stm32mp151.dtsi | 2676 +++++++++++++------------ arch/arm/boot/dts/st/stm32mp153.dtsi | 50 +- arch/arm/boot/dts/st/stm32mp15xc.dtsi | 18 +- 3 files changed, 1375 insertions(+), 1369 deletions(-)
diff --git a/arch/arm/boot/dts/st/stm32mp151.dtsi b/arch/arm/boot/dts/st/stm32mp151.dtsi index 61508917521c..78c0d6ccdb09 100644 --- a/arch/arm/boot/dts/st/stm32mp151.dtsi +++ b/arch/arm/boot/dts/st/stm32mp151.dtsi @@ -122,1543 +122,1551 @@ soc { interrupt-parent = <&intc>; ranges;
- timers2: timer@40000000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40000000 0x400>; - interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM2_K>; - clock-names = "int"; - dmas = <&dmamux1 18 0x400 0x1>, - <&dmamux1 19 0x400 0x1>, - <&dmamux1 20 0x400 0x1>, - <&dmamux1 21 0x400 0x1>, - <&dmamux1 22 0x400 0x1>; - dma-names = "ch1", "ch2", "ch3", "ch4", "up"; + ipcc: mailbox@4c001000 { + compatible = "st,stm32mp1-ipcc"; + #mbox-cells = <1>; + reg = <0x4c001000 0x400>; + st,proc-id = <0>; + interrupts-extended = + <&exti 61 1>, + <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + clocks = <&rcc IPCC>; + wakeup-source; status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@1 { - compatible = "st,stm32h7-timer-trigger"; - reg = <1>; - status = "disabled"; - }; - - counter { - compatible = "st,stm32-timer-counter"; - status = "disabled"; - }; + rcc: rcc@50000000 { + compatible = "st,stm32mp1-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; };
- timers3: timer@40001000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40001000 0x400>; - interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM3_K>; - clock-names = "int"; - dmas = <&dmamux1 23 0x400 0x1>, - <&dmamux1 24 0x400 0x1>, - <&dmamux1 25 0x400 0x1>, - <&dmamux1 26 0x400 0x1>, - <&dmamux1 27 0x400 0x1>, - <&dmamux1 28 0x400 0x1>; - dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; - status = "disabled"; + pwr_regulators: pwr@50001000 { + compatible = "st,stm32mp1,pwr-reg"; + reg = <0x50001000 0x10>;
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; + reg11: reg11 { + regulator-name = "reg11"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; };
- timer@2 { - compatible = "st,stm32h7-timer-trigger"; - reg = <2>; - status = "disabled"; + reg18: reg18 { + regulator-name = "reg18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; };
- counter { - compatible = "st,stm32-timer-counter"; - status = "disabled"; + usb33: usb33 { + regulator-name = "usb33"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; }; };
- timers4: timer@40002000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40002000 0x400>; - interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM4_K>; - clock-names = "int"; - dmas = <&dmamux1 29 0x400 0x1>, - <&dmamux1 30 0x400 0x1>, - <&dmamux1 31 0x400 0x1>, - <&dmamux1 32 0x400 0x1>; - dma-names = "ch1", "ch2", "ch3", "ch4"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; + pwr_mcu: pwr_mcu@50001014 { + compatible = "st,stm32mp151-pwr-mcu", "syscon"; + reg = <0x50001014 0x4>; + };
- timer@3 { - compatible = "st,stm32h7-timer-trigger"; - reg = <3>; - status = "disabled"; - }; + exti: interrupt-controller@5000d000 { + compatible = "st,stm32mp1-exti", "syscon"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x5000d000 0x400>; + };
- counter { - compatible = "st,stm32-timer-counter"; - status = "disabled"; - }; + syscfg: syscon@50020000 { + compatible = "st,stm32mp157-syscfg", "syscon"; + reg = <0x50020000 0x400>; + clocks = <&rcc SYSCFG>; };
- timers5: timer@40003000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40003000 0x400>; - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM5_K>; - clock-names = "int"; - dmas = <&dmamux1 55 0x400 0x1>, - <&dmamux1 56 0x400 0x1>, - <&dmamux1 57 0x400 0x1>, - <&dmamux1 58 0x400 0x1>, - <&dmamux1 59 0x400 0x1>, - <&dmamux1 60 0x400 0x1>; - dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; + dts: thermal@50028000 { + compatible = "st,stm32-thermal"; + reg = <0x50028000 0x100>; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc TMPSENS>; + clock-names = "pclk"; + #thermal-sensor-cells = <0>; status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@4 { - compatible = "st,stm32h7-timer-trigger"; - reg = <4>; - status = "disabled"; - }; - - counter { - compatible = "st,stm32-timer-counter"; - status = "disabled"; - }; + mdma1: dma-controller@58000000 { + compatible = "st,stm32h7-mdma"; + reg = <0x58000000 0x1000>; + interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc MDMA>; + resets = <&rcc MDMA_R>; + #dma-cells = <5>; + dma-channels = <32>; + dma-requests = <48>; };
- timers6: timer@40004000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40004000 0x400>; - interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM6_K>; - clock-names = "int"; - dmas = <&dmamux1 69 0x400 0x1>; - dma-names = "up"; + sdmmc1: mmc@58005000 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00253180>; + reg = <0x58005000 0x1000>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SDMMC1_K>; + clock-names = "apb_pclk"; + resets = <&rcc SDMMC1_R>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; status = "disabled"; - - timer@5 { - compatible = "st,stm32h7-timer-trigger"; - reg = <5>; - status = "disabled"; - }; };
- timers7: timer@40005000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40005000 0x400>; - interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM7_K>; - clock-names = "int"; - dmas = <&dmamux1 70 0x400 0x1>; - dma-names = "up"; + sdmmc2: mmc@58007000 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00253180>; + reg = <0x58007000 0x1000>; + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SDMMC2_K>; + clock-names = "apb_pclk"; + resets = <&rcc SDMMC2_R>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; status = "disabled"; - - timer@6 { - compatible = "st,stm32h7-timer-trigger"; - reg = <6>; - status = "disabled"; - }; };
- timers12: timer@40006000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40006000 0x400>; - interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM12_K>; - clock-names = "int"; + crc1: crc@58009000 { + compatible = "st,stm32f7-crc"; + reg = <0x58009000 0x400>; + clocks = <&rcc CRC1>; status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@11 { - compatible = "st,stm32h7-timer-trigger"; - reg = <11>; - status = "disabled"; - }; };
- timers13: timer@40007000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40007000 0x400>; - interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM13_K>; - clock-names = "int"; + usbh_ohci: usb@5800c000 { + compatible = "generic-ohci"; + reg = <0x5800c000 0x1000>; + clocks = <&usbphyc>, <&rcc USBH>; + resets = <&rcc USBH_R>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@12 { - compatible = "st,stm32h7-timer-trigger"; - reg = <12>; - status = "disabled"; - }; };
- timers14: timer@40008000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x40008000 0x400>; - interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM14_K>; - clock-names = "int"; + usbh_ehci: usb@5800d000 { + compatible = "generic-ehci"; + reg = <0x5800d000 0x1000>; + clocks = <&usbphyc>, <&rcc USBH>; + resets = <&rcc USBH_R>; + interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + companion = <&usbh_ohci>; status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; + ltdc: display-controller@5a001000 { + compatible = "st,stm32-ltdc"; + reg = <0x5a001000 0x400>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LTDC_PX>; + clock-names = "lcd"; + resets = <&rcc LTDC_R>; + status = "disabled"; + };
- timer@13 { - compatible = "st,stm32h7-timer-trigger"; - reg = <13>; - status = "disabled"; - }; + iwdg2: watchdog@5a002000 { + compatible = "st,stm32mp1-iwdg"; + reg = <0x5a002000 0x400>; + clocks = <&rcc IWDG2>, <&rcc CK_LSI>; + clock-names = "pclk", "lsi"; + status = "disabled"; };
- lptimer1: timer@40009000 { + usbphyc: usbphyc@5a006000 { #address-cells = <1>; #size-cells = <0>; - compatible = "st,stm32-lptimer"; - reg = <0x40009000 0x400>; - interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM1_K>; - clock-names = "mux"; - wakeup-source; + #clock-cells = <0>; + compatible = "st,stm32mp1-usbphyc"; + reg = <0x5a006000 0x1000>; + clocks = <&rcc USBPHY_K>; + resets = <&rcc USBPHY_R>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; status = "disabled";
- pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; - status = "disabled"; - }; - - trigger@0 { - compatible = "st,stm32-lptimer-trigger"; + usbphyc_port0: usb-phy@0 { + #phy-cells = <0>; reg = <0>; - status = "disabled"; };
- counter { - compatible = "st,stm32-lptimer-counter"; - status = "disabled"; + usbphyc_port1: usb-phy@1 { + #phy-cells = <1>; + reg = <1>; }; };
- spi2: spi@4000b000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x4000b000 0x400>; - interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI2_K>; - resets = <&rcc SPI2_R>; - dmas = <&dmamux1 39 0x400 0x05>, - <&dmamux1 40 0x400 0x05>; - dma-names = "rx", "tx"; + rtc: rtc@5c004000 { + compatible = "st,stm32mp1-rtc"; + reg = <0x5c004000 0x400>; + clocks = <&rcc RTCAPB>, <&rcc RTC>; + clock-names = "pclk", "rtc_ck"; + interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; };
- i2s2: audio-controller@4000b000 { - compatible = "st,stm32h7-i2s"; - #sound-dai-cells = <0>; - reg = <0x4000b000 0x400>; - interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 39 0x400 0x01>, - <&dmamux1 40 0x400 0x01>; - dma-names = "rx", "tx"; - status = "disabled"; + bsec: efuse@5c005000 { + compatible = "st,stm32mp15-bsec"; + reg = <0x5c005000 0x400>; + #address-cells = <1>; + #size-cells = <1>; + part_number_otp: part-number-otp@4 { + reg = <0x4 0x1>; + }; + vrefint: vrefin-cal@52 { + reg = <0x52 0x2>; + }; + ts_cal1: calib@5c { + reg = <0x5c 0x2>; + }; + ts_cal2: calib@5e { + reg = <0x5e 0x2>; + }; };
- spi3: spi@4000c000 { + etzpc: bus@5c007000 { + compatible = "st,stm32-etzpc"; + reg = <0x5c007000 0x400>; #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x4000c000 0x400>; - interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI3_K>; - resets = <&rcc SPI3_R>; - dmas = <&dmamux1 61 0x400 0x05>, - <&dmamux1 62 0x400 0x05>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + #size-cells = <1>; + ranges;
- i2s3: audio-controller@4000c000 { - compatible = "st,stm32h7-i2s"; - #sound-dai-cells = <0>; - reg = <0x4000c000 0x400>; - interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 61 0x400 0x01>, - <&dmamux1 62 0x400 0x01>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + timers2: timer@40000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40000000 0x400>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM2_K>; + clock-names = "int"; + dmas = <&dmamux1 18 0x400 0x1>, + <&dmamux1 19 0x400 0x1>, + <&dmamux1 20 0x400 0x1>, + <&dmamux1 21 0x400 0x1>, + <&dmamux1 22 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- spdifrx: audio-controller@4000d000 { - compatible = "st,stm32h7-spdifrx"; - #sound-dai-cells = <0>; - reg = <0x4000d000 0x400>; - clocks = <&rcc SPDIF_K>; - clock-names = "kclk"; - interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 93 0x400 0x01>, - <&dmamux1 94 0x400 0x01>; - dma-names = "rx", "rx-ctrl"; - status = "disabled"; - }; + timer@1 { + compatible = "st,stm32h7-timer-trigger"; + reg = <1>; + status = "disabled"; + };
- usart2: serial@4000e000 { - compatible = "st,stm32h7-uart"; - reg = <0x4000e000 0x400>; - interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc USART2_K>; - wakeup-source; - dmas = <&dmamux1 43 0x400 0x15>, - <&dmamux1 44 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + counter { + compatible = "st,stm32-timer-counter"; + status = "disabled"; + }; + };
- usart3: serial@4000f000 { - compatible = "st,stm32h7-uart"; - reg = <0x4000f000 0x400>; - interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc USART3_K>; - wakeup-source; - dmas = <&dmamux1 45 0x400 0x15>, - <&dmamux1 46 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + timers3: timer@40001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40001000 0x400>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM3_K>; + clock-names = "int"; + dmas = <&dmamux1 23 0x400 0x1>, + <&dmamux1 24 0x400 0x1>, + <&dmamux1 25 0x400 0x1>, + <&dmamux1 26 0x400 0x1>, + <&dmamux1 27 0x400 0x1>, + <&dmamux1 28 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- uart4: serial@40010000 { - compatible = "st,stm32h7-uart"; - reg = <0x40010000 0x400>; - interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc UART4_K>; - wakeup-source; - dmas = <&dmamux1 63 0x400 0x15>, - <&dmamux1 64 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + timer@2 { + compatible = "st,stm32h7-timer-trigger"; + reg = <2>; + status = "disabled"; + };
- uart5: serial@40011000 { - compatible = "st,stm32h7-uart"; - reg = <0x40011000 0x400>; - interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc UART5_K>; - wakeup-source; - dmas = <&dmamux1 65 0x400 0x15>, - <&dmamux1 66 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + counter { + compatible = "st,stm32-timer-counter"; + status = "disabled"; + }; + };
- i2c1: i2c@40012000 { - compatible = "st,stm32mp15-i2c"; - reg = <0x40012000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C1_K>; - resets = <&rcc I2C1_R>; - #address-cells = <1>; - #size-cells = <0>; - st,syscfg-fmp = <&syscfg 0x4 0x1>; - wakeup-source; - i2c-analog-filter; - status = "disabled"; - }; + timers4: timer@40002000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40002000 0x400>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM4_K>; + clock-names = "int"; + dmas = <&dmamux1 29 0x400 0x1>, + <&dmamux1 30 0x400 0x1>, + <&dmamux1 31 0x400 0x1>, + <&dmamux1 32 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- i2c2: i2c@40013000 { - compatible = "st,stm32mp15-i2c"; - reg = <0x40013000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C2_K>; - resets = <&rcc I2C2_R>; - #address-cells = <1>; - #size-cells = <0>; - st,syscfg-fmp = <&syscfg 0x4 0x2>; - wakeup-source; - i2c-analog-filter; - status = "disabled"; - }; + timer@3 { + compatible = "st,stm32h7-timer-trigger"; + reg = <3>; + status = "disabled"; + };
- i2c3: i2c@40014000 { - compatible = "st,stm32mp15-i2c"; - reg = <0x40014000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C3_K>; - resets = <&rcc I2C3_R>; - #address-cells = <1>; - #size-cells = <0>; - st,syscfg-fmp = <&syscfg 0x4 0x4>; - wakeup-source; - i2c-analog-filter; - status = "disabled"; - }; + counter { + compatible = "st,stm32-timer-counter"; + status = "disabled"; + }; + };
- i2c5: i2c@40015000 { - compatible = "st,stm32mp15-i2c"; - reg = <0x40015000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C5_K>; - resets = <&rcc I2C5_R>; - #address-cells = <1>; - #size-cells = <0>; - st,syscfg-fmp = <&syscfg 0x4 0x10>; - wakeup-source; - i2c-analog-filter; - status = "disabled"; - }; + timers5: timer@40003000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40003000 0x400>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM5_K>; + clock-names = "int"; + dmas = <&dmamux1 55 0x400 0x1>, + <&dmamux1 56 0x400 0x1>, + <&dmamux1 57 0x400 0x1>, + <&dmamux1 58 0x400 0x1>, + <&dmamux1 59 0x400 0x1>, + <&dmamux1 60 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- cec: cec@40016000 { - compatible = "st,stm32-cec"; - reg = <0x40016000 0x400>; - interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc CEC_K>, <&rcc CEC>; - clock-names = "cec", "hdmi-cec"; - status = "disabled"; - }; + timer@4 { + compatible = "st,stm32h7-timer-trigger"; + reg = <4>; + status = "disabled"; + };
- dac: dac@40017000 { - compatible = "st,stm32h7-dac-core"; - reg = <0x40017000 0x400>; - clocks = <&rcc DAC12>; - clock-names = "pclk"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; + counter { + compatible = "st,stm32-timer-counter"; + status = "disabled"; + }; + };
- dac1: dac@1 { - compatible = "st,stm32-dac"; - #io-channel-cells = <1>; - reg = <1>; - status = "disabled"; + timers6: timer@40004000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40004000 0x400>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM6_K>; + clock-names = "int"; + dmas = <&dmamux1 69 0x400 0x1>; + dma-names = "up"; + status = "disabled"; + + timer@5 { + compatible = "st,stm32h7-timer-trigger"; + reg = <5>; + status = "disabled"; + }; };
- dac2: dac@2 { - compatible = "st,stm32-dac"; - #io-channel-cells = <1>; - reg = <2>; - status = "disabled"; + timers7: timer@40005000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40005000 0x400>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM7_K>; + clock-names = "int"; + dmas = <&dmamux1 70 0x400 0x1>; + dma-names = "up"; + status = "disabled"; + + timer@6 { + compatible = "st,stm32h7-timer-trigger"; + reg = <6>; + status = "disabled"; + }; }; - };
- uart7: serial@40018000 { - compatible = "st,stm32h7-uart"; - reg = <0x40018000 0x400>; - interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc UART7_K>; - wakeup-source; - dmas = <&dmamux1 79 0x400 0x15>, - <&dmamux1 80 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + timers12: timer@40006000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40006000 0x400>; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM12_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- uart8: serial@40019000 { - compatible = "st,stm32h7-uart"; - reg = <0x40019000 0x400>; - interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc UART8_K>; - wakeup-source; - dmas = <&dmamux1 81 0x400 0x15>, - <&dmamux1 82 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + timer@11 { + compatible = "st,stm32h7-timer-trigger"; + reg = <11>; + status = "disabled"; + }; + };
- timers1: timer@44000000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x44000000 0x400>; - interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "brk", "up", "trg-com", "cc"; - clocks = <&rcc TIM1_K>; - clock-names = "int"; - dmas = <&dmamux1 11 0x400 0x1>, - <&dmamux1 12 0x400 0x1>, - <&dmamux1 13 0x400 0x1>, - <&dmamux1 14 0x400 0x1>, - <&dmamux1 15 0x400 0x1>, - <&dmamux1 16 0x400 0x1>, - <&dmamux1 17 0x400 0x1>; - dma-names = "ch1", "ch2", "ch3", "ch4", - "up", "trig", "com"; - status = "disabled"; + timers13: timer@40007000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40007000 0x400>; + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM13_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; + timer@12 { + compatible = "st,stm32h7-timer-trigger"; + reg = <12>; + status = "disabled"; + }; };
- timer@0 { - compatible = "st,stm32h7-timer-trigger"; - reg = <0>; - status = "disabled"; - }; + timers14: timer@40008000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x40008000 0x400>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM14_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- counter { - compatible = "st,stm32-timer-counter"; - status = "disabled"; + timer@13 { + compatible = "st,stm32h7-timer-trigger"; + reg = <13>; + status = "disabled"; + }; }; - };
- timers8: timer@44001000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x44001000 0x400>; - interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "brk", "up", "trg-com", "cc"; - clocks = <&rcc TIM8_K>; - clock-names = "int"; - dmas = <&dmamux1 47 0x400 0x1>, - <&dmamux1 48 0x400 0x1>, - <&dmamux1 49 0x400 0x1>, - <&dmamux1 50 0x400 0x1>, - <&dmamux1 51 0x400 0x1>, - <&dmamux1 52 0x400 0x1>, - <&dmamux1 53 0x400 0x1>; - dma-names = "ch1", "ch2", "ch3", "ch4", - "up", "trig", "com"; - status = "disabled"; + lptimer1: timer@40009000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x40009000 0x400>; + interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM1_K>; + clock-names = "mux"; + wakeup-source; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; + trigger@0 { + compatible = "st,stm32-lptimer-trigger"; + reg = <0>; + status = "disabled"; + }; + + counter { + compatible = "st,stm32-lptimer-counter"; + status = "disabled"; + }; };
- timer@7 { - compatible = "st,stm32h7-timer-trigger"; - reg = <7>; + i2s2: audio-controller@4000b000 { + compatible = "st,stm32h7-i2s"; + #sound-dai-cells = <0>; + reg = <0x4000b000 0x400>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 39 0x400 0x01>, + <&dmamux1 40 0x400 0x01>; + dma-names = "rx", "tx"; status = "disabled"; };
- counter { - compatible = "st,stm32-timer-counter"; + spi2: spi@4000b000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x4000b000 0x400>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI2_K>; + resets = <&rcc SPI2_R>; + dmas = <&dmamux1 39 0x400 0x05>, + <&dmamux1 40 0x400 0x05>; + dma-names = "rx", "tx"; status = "disabled"; }; - }; - - usart6: serial@44003000 { - compatible = "st,stm32h7-uart"; - reg = <0x44003000 0x400>; - interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc USART6_K>; - wakeup-source; - dmas = <&dmamux1 71 0x400 0x15>, - <&dmamux1 72 0x400 0x11>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - spi1: spi@44004000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x44004000 0x400>; - interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI1_K>; - resets = <&rcc SPI1_R>; - dmas = <&dmamux1 37 0x400 0x05>, - <&dmamux1 38 0x400 0x05>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - i2s1: audio-controller@44004000 { - compatible = "st,stm32h7-i2s"; - #sound-dai-cells = <0>; - reg = <0x44004000 0x400>; - interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 37 0x400 0x01>, - <&dmamux1 38 0x400 0x01>; - dma-names = "rx", "tx"; - status = "disabled"; - };
- spi4: spi@44005000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x44005000 0x400>; - interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI4_K>; - resets = <&rcc SPI4_R>; - dmas = <&dmamux1 83 0x400 0x05>, - <&dmamux1 84 0x400 0x05>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - timers15: timer@44006000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x44006000 0x400>; - interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM15_K>; - clock-names = "int"; - dmas = <&dmamux1 105 0x400 0x1>, - <&dmamux1 106 0x400 0x1>, - <&dmamux1 107 0x400 0x1>, - <&dmamux1 108 0x400 0x1>; - dma-names = "ch1", "up", "trig", "com"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; + i2s3: audio-controller@4000c000 { + compatible = "st,stm32h7-i2s"; + #sound-dai-cells = <0>; + reg = <0x4000c000 0x400>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 61 0x400 0x01>, + <&dmamux1 62 0x400 0x01>; + dma-names = "rx", "tx"; status = "disabled"; };
- timer@14 { - compatible = "st,stm32h7-timer-trigger"; - reg = <14>; + spi3: spi@4000c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x4000c000 0x400>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI3_K>; + resets = <&rcc SPI3_R>; + dmas = <&dmamux1 61 0x400 0x05>, + <&dmamux1 62 0x400 0x05>; + dma-names = "rx", "tx"; status = "disabled"; }; - }; - - timers16: timer@44007000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x44007000 0x400>; - interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM16_K>; - clock-names = "int"; - dmas = <&dmamux1 109 0x400 0x1>, - <&dmamux1 110 0x400 0x1>; - dma-names = "ch1", "up"; - status = "disabled";
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; + spdifrx: audio-controller@4000d000 { + compatible = "st,stm32h7-spdifrx"; + #sound-dai-cells = <0>; + reg = <0x4000d000 0x400>; + clocks = <&rcc SPDIF_K>; + clock-names = "kclk"; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 93 0x400 0x01>, + <&dmamux1 94 0x400 0x01>; + dma-names = "rx", "rx-ctrl"; + status = "disabled"; + }; + + usart2: serial@4000e000 { + compatible = "st,stm32h7-uart"; + reg = <0x4000e000 0x400>; + interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART2_K>; + wakeup-source; + dmas = <&dmamux1 43 0x400 0x15>, + <&dmamux1 44 0x400 0x11>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + usart3: serial@4000f000 { + compatible = "st,stm32h7-uart"; + reg = <0x4000f000 0x400>; + interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART3_K>; + wakeup-source; + dmas = <&dmamux1 45 0x400 0x15>, + <&dmamux1 46 0x400 0x11>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart4: serial@40010000 { + compatible = "st,stm32h7-uart"; + reg = <0x40010000 0x400>; + interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART4_K>; + wakeup-source; + dmas = <&dmamux1 63 0x400 0x15>, + <&dmamux1 64 0x400 0x11>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + uart5: serial@40011000 { + compatible = "st,stm32h7-uart"; + reg = <0x40011000 0x400>; + interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART5_K>; + wakeup-source; + dmas = <&dmamux1 65 0x400 0x15>, + <&dmamux1 66 0x400 0x11>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2c1: i2c@40012000 { + compatible = "st,stm32mp15-i2c"; + reg = <0x40012000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C1_K>; + resets = <&rcc I2C1_R>; + #address-cells = <1>; + #size-cells = <0>; + st,syscfg-fmp = <&syscfg 0x4 0x1>; + wakeup-source; + i2c-analog-filter; status = "disabled"; }; - timer@15 { - compatible = "st,stm32h7-timer-trigger"; - reg = <15>; + + i2c2: i2c@40013000 { + compatible = "st,stm32mp15-i2c"; + reg = <0x40013000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C2_K>; + resets = <&rcc I2C2_R>; + #address-cells = <1>; + #size-cells = <0>; + st,syscfg-fmp = <&syscfg 0x4 0x2>; + wakeup-source; + i2c-analog-filter; status = "disabled"; }; - };
- timers17: timer@44008000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x44008000 0x400>; - interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM17_K>; - clock-names = "int"; - dmas = <&dmamux1 111 0x400 0x1>, - <&dmamux1 112 0x400 0x1>; - dma-names = "ch1", "up"; - status = "disabled"; + i2c3: i2c@40014000 { + compatible = "st,stm32mp15-i2c"; + reg = <0x40014000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C3_K>; + resets = <&rcc I2C3_R>; + #address-cells = <1>; + #size-cells = <0>; + st,syscfg-fmp = <&syscfg 0x4 0x4>; + wakeup-source; + i2c-analog-filter; + status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; + i2c5: i2c@40015000 { + compatible = "st,stm32mp15-i2c"; + reg = <0x40015000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C5_K>; + resets = <&rcc I2C5_R>; + #address-cells = <1>; + #size-cells = <0>; + st,syscfg-fmp = <&syscfg 0x4 0x10>; + wakeup-source; + i2c-analog-filter; status = "disabled"; };
- timer@16 { - compatible = "st,stm32h7-timer-trigger"; - reg = <16>; + cec: cec@40016000 { + compatible = "st,stm32-cec"; + reg = <0x40016000 0x400>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CEC_K>, <&rcc CEC>; + clock-names = "cec", "hdmi-cec"; status = "disabled"; }; - };
- spi5: spi@44009000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x44009000 0x400>; - interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI5_K>; - resets = <&rcc SPI5_R>; - dmas = <&dmamux1 85 0x400 0x05>, - <&dmamux1 86 0x400 0x05>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + dac: dac@40017000 { + compatible = "st,stm32h7-dac-core"; + reg = <0x40017000 0x400>; + clocks = <&rcc DAC12>; + clock-names = "pclk"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled";
- sai1: sai@4400a000 { - compatible = "st,stm32h7-sai"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x4400a000 0x400>; - reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>; - interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; - resets = <&rcc SAI1_R>; - status = "disabled"; + dac1: dac@1 { + compatible = "st,stm32-dac"; + #io-channel-cells = <1>; + reg = <1>; + status = "disabled"; + };
- sai1a: audio-controller@4400a004 { - #sound-dai-cells = <0>; + dac2: dac@2 { + compatible = "st,stm32-dac"; + #io-channel-cells = <1>; + reg = <2>; + status = "disabled"; + }; + };
- compatible = "st,stm32-sai-sub-a"; - reg = <0x4 0x20>; - clocks = <&rcc SAI1_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 87 0x400 0x01>; + uart7: serial@40018000 { + compatible = "st,stm32h7-uart"; + reg = <0x40018000 0x400>; + interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART7_K>; + wakeup-source; + dmas = <&dmamux1 79 0x400 0x15>, + <&dmamux1 80 0x400 0x11>; + dma-names = "rx", "tx"; status = "disabled"; };
- sai1b: audio-controller@4400a024 { - #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-b"; - reg = <0x24 0x20>; - clocks = <&rcc SAI1_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 88 0x400 0x01>; + uart8: serial@40019000 { + compatible = "st,stm32h7-uart"; + reg = <0x40019000 0x400>; + interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc UART8_K>; + wakeup-source; + dmas = <&dmamux1 81 0x400 0x15>, + <&dmamux1 82 0x400 0x11>; + dma-names = "rx", "tx"; status = "disabled"; }; - };
- sai2: sai@4400b000 { - compatible = "st,stm32h7-sai"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x4400b000 0x400>; - reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>; - interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; - resets = <&rcc SAI2_R>; - status = "disabled"; + timers1: timer@44000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44000000 0x400>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "brk", "up", "trg-com", "cc"; + clocks = <&rcc TIM1_K>; + clock-names = "int"; + dmas = <&dmamux1 11 0x400 0x1>, + <&dmamux1 12 0x400 0x1>, + <&dmamux1 13 0x400 0x1>, + <&dmamux1 14 0x400 0x1>, + <&dmamux1 15 0x400 0x1>, + <&dmamux1 16 0x400 0x1>, + <&dmamux1 17 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", + "up", "trig", "com"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- sai2a: audio-controller@4400b004 { - #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-a"; - reg = <0x4 0x20>; - clocks = <&rcc SAI2_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 89 0x400 0x01>; - status = "disabled"; - }; + timer@0 { + compatible = "st,stm32h7-timer-trigger"; + reg = <0>; + status = "disabled"; + };
- sai2b: audio-controller@4400b024 { - #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-b"; - reg = <0x24 0x20>; - clocks = <&rcc SAI2_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 90 0x400 0x01>; - status = "disabled"; + counter { + compatible = "st,stm32-timer-counter"; + status = "disabled"; + }; }; - };
- sai3: sai@4400c000 { - compatible = "st,stm32h7-sai"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x4400c000 0x400>; - reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>; - interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; - resets = <&rcc SAI3_R>; - status = "disabled"; + timers8: timer@44001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44001000 0x400>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "brk", "up", "trg-com", "cc"; + clocks = <&rcc TIM8_K>; + clock-names = "int"; + dmas = <&dmamux1 47 0x400 0x1>, + <&dmamux1 48 0x400 0x1>, + <&dmamux1 49 0x400 0x1>, + <&dmamux1 50 0x400 0x1>, + <&dmamux1 51 0x400 0x1>, + <&dmamux1 52 0x400 0x1>, + <&dmamux1 53 0x400 0x1>; + dma-names = "ch1", "ch2", "ch3", "ch4", + "up", "trig", "com"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + };
- sai3a: audio-controller@4400c004 { - #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-a"; - reg = <0x04 0x20>; - clocks = <&rcc SAI3_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 113 0x400 0x01>; + timer@7 { + compatible = "st,stm32h7-timer-trigger"; + reg = <7>; + status = "disabled"; + }; + + counter { + compatible = "st,stm32-timer-counter"; + status = "disabled"; + }; + }; + + usart6: serial@44003000 { + compatible = "st,stm32h7-uart"; + reg = <0x44003000 0x400>; + interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART6_K>; + wakeup-source; + dmas = <&dmamux1 71 0x400 0x15>, + <&dmamux1 72 0x400 0x11>; + dma-names = "rx", "tx"; status = "disabled"; };
- sai3b: audio-controller@4400c024 { + i2s1: audio-controller@44004000 { + compatible = "st,stm32h7-i2s"; #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-b"; - reg = <0x24 0x20>; - clocks = <&rcc SAI3_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 114 0x400 0x01>; + reg = <0x44004000 0x400>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 37 0x400 0x01>, + <&dmamux1 38 0x400 0x01>; + dma-names = "rx", "tx"; status = "disabled"; }; - }; - - dfsdm: dfsdm@4400d000 { - compatible = "st,stm32mp1-dfsdm"; - reg = <0x4400d000 0x800>; - clocks = <&rcc DFSDM_K>; - clock-names = "dfsdm"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled";
- dfsdm0: filter@0 { - compatible = "st,stm32-dfsdm-adc"; - #io-channel-cells = <1>; - reg = <0>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 101 0x400 0x01>; - dma-names = "rx"; + spi1: spi@44004000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x44004000 0x400>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI1_K>; + resets = <&rcc SPI1_R>; + dmas = <&dmamux1 37 0x400 0x05>, + <&dmamux1 38 0x400 0x05>; + dma-names = "rx", "tx"; status = "disabled"; };
- dfsdm1: filter@1 { - compatible = "st,stm32-dfsdm-adc"; - #io-channel-cells = <1>; - reg = <1>; - interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 102 0x400 0x01>; - dma-names = "rx"; + spi4: spi@44005000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x44005000 0x400>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI4_K>; + resets = <&rcc SPI4_R>; + dmas = <&dmamux1 83 0x400 0x05>, + <&dmamux1 84 0x400 0x05>; + dma-names = "rx", "tx"; status = "disabled"; };
- dfsdm2: filter@2 { - compatible = "st,stm32-dfsdm-adc"; - #io-channel-cells = <1>; - reg = <2>; - interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 103 0x400 0x01>; - dma-names = "rx"; - status = "disabled"; + timers15: timer@44006000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44006000 0x400>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM15_K>; + clock-names = "int"; + dmas = <&dmamux1 105 0x400 0x1>, + <&dmamux1 106 0x400 0x1>, + <&dmamux1 107 0x400 0x1>, + <&dmamux1 108 0x400 0x1>; + dma-names = "ch1", "up", "trig", "com"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@14 { + compatible = "st,stm32h7-timer-trigger"; + reg = <14>; + status = "disabled"; + }; };
- dfsdm3: filter@3 { - compatible = "st,stm32-dfsdm-adc"; - #io-channel-cells = <1>; - reg = <3>; - interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 104 0x400 0x01>; - dma-names = "rx"; - status = "disabled"; + timers16: timer@44007000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44007000 0x400>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM16_K>; + clock-names = "int"; + dmas = <&dmamux1 109 0x400 0x1>, + <&dmamux1 110 0x400 0x1>; + dma-names = "ch1", "up"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + timer@15 { + compatible = "st,stm32h7-timer-trigger"; + reg = <15>; + status = "disabled"; + }; };
- dfsdm4: filter@4 { - compatible = "st,stm32-dfsdm-adc"; - #io-channel-cells = <1>; - reg = <4>; - interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 91 0x400 0x01>; - dma-names = "rx"; - status = "disabled"; + timers17: timer@44008000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x44008000 0x400>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM17_K>; + clock-names = "int"; + dmas = <&dmamux1 111 0x400 0x1>, + <&dmamux1 112 0x400 0x1>; + dma-names = "ch1", "up"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@16 { + compatible = "st,stm32h7-timer-trigger"; + reg = <16>; + status = "disabled"; + }; };
- dfsdm5: filter@5 { - compatible = "st,stm32-dfsdm-adc"; - #io-channel-cells = <1>; - reg = <5>; - interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 92 0x400 0x01>; - dma-names = "rx"; + spi5: spi@44009000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x44009000 0x400>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI5_K>; + resets = <&rcc SPI5_R>; + dmas = <&dmamux1 85 0x400 0x05>, + <&dmamux1 86 0x400 0x05>; + dma-names = "rx", "tx"; status = "disabled"; }; - };
- dma1: dma-controller@48000000 { - compatible = "st,stm32-dma"; - reg = <0x48000000 0x400>; - interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc DMA1>; - resets = <&rcc DMA1_R>; - #dma-cells = <4>; - st,mem2mem; - dma-requests = <8>; - }; + sai1: sai@4400a000 { + compatible = "st,stm32h7-sai"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x4400a000 0x400>; + reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc SAI1_R>; + status = "disabled"; + + sai1a: audio-controller@4400a004 { + #sound-dai-cells = <0>; + + compatible = "st,stm32-sai-sub-a"; + reg = <0x4 0x20>; + clocks = <&rcc SAI1_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 87 0x400 0x01>; + status = "disabled"; + };
- dma2: dma-controller@48001000 { - compatible = "st,stm32-dma"; - reg = <0x48001000 0x400>; - interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc DMA2>; - resets = <&rcc DMA2_R>; - #dma-cells = <4>; - st,mem2mem; - dma-requests = <8>; - }; + sai1b: audio-controller@4400a024 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-b"; + reg = <0x24 0x20>; + clocks = <&rcc SAI1_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 88 0x400 0x01>; + status = "disabled"; + }; + };
- dmamux1: dma-router@48002000 { - compatible = "st,stm32h7-dmamux"; - reg = <0x48002000 0x40>; - #dma-cells = <3>; - dma-requests = <128>; - dma-masters = <&dma1 &dma2>; - dma-channels = <16>; - clocks = <&rcc DMAMUX>; - resets = <&rcc DMAMUX_R>; - }; + sai2: sai@4400b000 { + compatible = "st,stm32h7-sai"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x4400b000 0x400>; + reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc SAI2_R>; + status = "disabled"; + + sai2a: audio-controller@4400b004 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-a"; + reg = <0x4 0x20>; + clocks = <&rcc SAI2_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 89 0x400 0x01>; + status = "disabled"; + };
- adc: adc@48003000 { - compatible = "st,stm32mp1-adc-core"; - reg = <0x48003000 0x400>; - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc ADC12>, <&rcc ADC12_K>; - clock-names = "bus", "adc"; - interrupt-controller; - st,syscfg = <&syscfg>; - #interrupt-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; + sai2b: audio-controller@4400b024 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-b"; + reg = <0x24 0x20>; + clocks = <&rcc SAI2_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 90 0x400 0x01>; + status = "disabled"; + }; + };
- adc1: adc@0 { - compatible = "st,stm32mp1-adc"; - #io-channel-cells = <1>; + sai3: sai@4400c000 { + compatible = "st,stm32h7-sai"; #address-cells = <1>; - #size-cells = <0>; - reg = <0x0>; - interrupt-parent = <&adc>; - interrupts = <0>; - dmas = <&dmamux1 9 0x400 0x01>; - dma-names = "rx"; - status = "disabled"; + #size-cells = <1>; + ranges = <0 0x4400c000 0x400>; + reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc SAI3_R>; + status = "disabled"; + + sai3a: audio-controller@4400c004 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-a"; + reg = <0x04 0x20>; + clocks = <&rcc SAI3_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 113 0x400 0x01>; + status = "disabled"; + }; + + sai3b: audio-controller@4400c024 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-b"; + reg = <0x24 0x20>; + clocks = <&rcc SAI3_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 114 0x400 0x01>; + status = "disabled"; + }; };
- adc2: adc@100 { - compatible = "st,stm32mp1-adc"; - #io-channel-cells = <1>; + dfsdm: dfsdm@4400d000 { + compatible = "st,stm32mp1-dfsdm"; + reg = <0x4400d000 0x800>; + clocks = <&rcc DFSDM_K>; + clock-names = "dfsdm"; #address-cells = <1>; #size-cells = <0>; - reg = <0x100>; - interrupt-parent = <&adc>; - interrupts = <1>; - dmas = <&dmamux1 10 0x400 0x01>; - dma-names = "rx"; - nvmem-cells = <&vrefint>; - nvmem-cell-names = "vrefint"; - status = "disabled"; - channel@13 { - reg = <13>; - label = "vrefint"; + status = "disabled"; + + dfsdm0: filter@0 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <0>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 101 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; }; - channel@14 { - reg = <14>; - label = "vddcore"; + + dfsdm1: filter@1 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <1>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 102 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; }; - }; - };
- sdmmc3: mmc@48004000 { - compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00253180>; - reg = <0x48004000 0x400>; - interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SDMMC3_K>; - clock-names = "apb_pclk"; - resets = <&rcc SDMMC3_R>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <120000000>; - status = "disabled"; - }; + dfsdm2: filter@2 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <2>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 103 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; + };
- usbotg_hs: usb-otg@49000000 { - compatible = "st,stm32mp15-hsotg", "snps,dwc2"; - reg = <0x49000000 0x10000>; - clocks = <&rcc USBO_K>, <&usbphyc>; - clock-names = "otg", "utmi"; - resets = <&rcc USBO_R>; - reset-names = "dwc2"; - interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; - g-rx-fifo-size = <512>; - g-np-tx-fifo-size = <32>; - g-tx-fifo-size = <256 16 16 16 16 16 16 16>; - dr_mode = "otg"; - otg-rev = <0x200>; - usb33d-supply = <&usb33>; - status = "disabled"; - }; - - ipcc: mailbox@4c001000 { - compatible = "st,stm32mp1-ipcc"; - #mbox-cells = <1>; - reg = <0x4c001000 0x400>; - st,proc-id = <0>; - interrupts-extended = - <&exti 61 1>, - <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "rx", "tx"; - clocks = <&rcc IPCC>; - wakeup-source; - status = "disabled"; - }; - - dcmi: dcmi@4c006000 { - compatible = "st,stm32-dcmi"; - reg = <0x4c006000 0x400>; - interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; - resets = <&rcc CAMITF_R>; - clocks = <&rcc DCMI>; - clock-names = "mclk"; - dmas = <&dmamux1 75 0x400 0x01>; - dma-names = "tx"; - status = "disabled"; - }; - - rcc: rcc@50000000 { - compatible = "st,stm32mp1-rcc", "syscon"; - reg = <0x50000000 0x1000>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - pwr_regulators: pwr@50001000 { - compatible = "st,stm32mp1,pwr-reg"; - reg = <0x50001000 0x10>; - - reg11: reg11 { - regulator-name = "reg11"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - }; + dfsdm3: filter@3 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <3>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 104 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; + };
- reg18: reg18 { - regulator-name = "reg18"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; + dfsdm4: filter@4 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <4>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 91 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; + };
- usb33: usb33 { - regulator-name = "usb33"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; + dfsdm5: filter@5 { + compatible = "st,stm32-dfsdm-adc"; + #io-channel-cells = <1>; + reg = <5>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 92 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; + }; }; - }; - - pwr_mcu: pwr_mcu@50001014 { - compatible = "st,stm32mp151-pwr-mcu", "syscon"; - reg = <0x50001014 0x4>; - }; - - exti: interrupt-controller@5000d000 { - compatible = "st,stm32mp1-exti", "syscon"; - interrupt-controller; - #interrupt-cells = <2>; - reg = <0x5000d000 0x400>; - };
- syscfg: syscon@50020000 { - compatible = "st,stm32mp157-syscfg", "syscon"; - reg = <0x50020000 0x400>; - clocks = <&rcc SYSCFG>; - }; + dma1: dma-controller@48000000 { + compatible = "st,stm32-dma"; + reg = <0x48000000 0x400>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc DMA1>; + resets = <&rcc DMA1_R>; + #dma-cells = <4>; + st,mem2mem; + dma-requests = <8>; + }; + + dma2: dma-controller@48001000 { + compatible = "st,stm32-dma"; + reg = <0x48001000 0x400>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc DMA2>; + resets = <&rcc DMA2_R>; + #dma-cells = <4>; + st,mem2mem; + dma-requests = <8>; + }; + + dmamux1: dma-router@48002000 { + compatible = "st,stm32h7-dmamux"; + reg = <0x48002000 0x40>; + #dma-cells = <3>; + dma-requests = <128>; + dma-masters = <&dma1 &dma2>; + dma-channels = <16>; + clocks = <&rcc DMAMUX>; + resets = <&rcc DMAMUX_R>; + }; + + adc: adc@48003000 { + compatible = "st,stm32mp1-adc-core"; + reg = <0x48003000 0x400>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc ADC12>, <&rcc ADC12_K>; + clock-names = "bus", "adc"; + interrupt-controller; + st,syscfg = <&syscfg>; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled";
- lptimer2: timer@50021000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-lptimer"; - reg = <0x50021000 0x400>; - interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM2_K>; - clock-names = "mux"; - wakeup-source; - status = "disabled"; + adc1: adc@0 { + compatible = "st,stm32mp1-adc"; + #io-channel-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + interrupt-parent = <&adc>; + interrupts = <0>; + dmas = <&dmamux1 9 0x400 0x01>; + dma-names = "rx"; + status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; - status = "disabled"; + adc2: adc@100 { + compatible = "st,stm32mp1-adc"; + #io-channel-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x100>; + interrupt-parent = <&adc>; + interrupts = <1>; + dmas = <&dmamux1 10 0x400 0x01>; + dma-names = "rx"; + nvmem-cells = <&vrefint>; + nvmem-cell-names = "vrefint"; + status = "disabled"; + channel@13 { + reg = <13>; + label = "vrefint"; + }; + channel@14 { + reg = <14>; + label = "vddcore"; + }; + }; };
- trigger@1 { - compatible = "st,stm32-lptimer-trigger"; - reg = <1>; + sdmmc3: mmc@48004000 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00253180>; + reg = <0x48004000 0x400>; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SDMMC3_K>; + clock-names = "apb_pclk"; + resets = <&rcc SDMMC3_R>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; status = "disabled"; };
- counter { - compatible = "st,stm32-lptimer-counter"; + usbotg_hs: usb-otg@49000000 { + compatible = "st,stm32mp15-hsotg", "snps,dwc2"; + reg = <0x49000000 0x10000>; + clocks = <&rcc USBO_K>, <&usbphyc>; + clock-names = "otg", "utmi"; + resets = <&rcc USBO_R>; + reset-names = "dwc2"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + g-rx-fifo-size = <512>; + g-np-tx-fifo-size = <32>; + g-tx-fifo-size = <256 16 16 16 16 16 16 16>; + dr_mode = "otg"; + otg-rev = <0x200>; + usb33d-supply = <&usb33>; status = "disabled"; }; - }; - - lptimer3: timer@50022000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-lptimer"; - reg = <0x50022000 0x400>; - interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM3_K>; - clock-names = "mux"; - wakeup-source; - status = "disabled";
- pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; + dcmi: dcmi@4c006000 { + compatible = "st,stm32-dcmi"; + reg = <0x4c006000 0x400>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc CAMITF_R>; + clocks = <&rcc DCMI>; + clock-names = "mclk"; + dmas = <&dmamux1 75 0x400 0x01>; + dma-names = "tx"; status = "disabled"; };
- trigger@2 { - compatible = "st,stm32-lptimer-trigger"; - reg = <2>; - status = "disabled"; - }; - }; + lptimer2: timer@50021000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x50021000 0x400>; + interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM2_K>; + clock-names = "mux"; + wakeup-source; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + };
- lptimer4: timer@50023000 { - compatible = "st,stm32-lptimer"; - reg = <0x50023000 0x400>; - interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM4_K>; - clock-names = "mux"; - wakeup-source; - status = "disabled"; + trigger@1 { + compatible = "st,stm32-lptimer-trigger"; + reg = <1>; + status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; - status = "disabled"; + counter { + compatible = "st,stm32-lptimer-counter"; + status = "disabled"; + }; }; - };
- lptimer5: timer@50024000 { - compatible = "st,stm32-lptimer"; - reg = <0x50024000 0x400>; - interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM5_K>; - clock-names = "mux"; - wakeup-source; - status = "disabled"; + lptimer3: timer@50022000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x50022000 0x400>; + interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM3_K>; + clock-names = "mux"; + wakeup-source; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + };
- pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; - status = "disabled"; + trigger@2 { + compatible = "st,stm32-lptimer-trigger"; + reg = <2>; + status = "disabled"; + }; }; - };
- vrefbuf: vrefbuf@50025000 { - compatible = "st,stm32-vrefbuf"; - reg = <0x50025000 0x8>; - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <2500000>; - clocks = <&rcc VREF>; - status = "disabled"; - }; + lptimer4: timer@50023000 { + compatible = "st,stm32-lptimer"; + reg = <0x50023000 0x400>; + interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM4_K>; + clock-names = "mux"; + wakeup-source; + status = "disabled";
- sai4: sai@50027000 { - compatible = "st,stm32h7-sai"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x50027000 0x400>; - reg = <0x50027000 0x4>, <0x500273f0 0x10>; - interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; - resets = <&rcc SAI4_R>; - status = "disabled"; + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + };
- sai4a: audio-controller@50027004 { - #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-a"; - reg = <0x04 0x20>; - clocks = <&rcc SAI4_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 99 0x400 0x01>; + lptimer5: timer@50024000 { + compatible = "st,stm32-lptimer"; + reg = <0x50024000 0x400>; + interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM5_K>; + clock-names = "mux"; + wakeup-source; status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; };
- sai4b: audio-controller@50027024 { - #sound-dai-cells = <0>; - compatible = "st,stm32-sai-sub-b"; - reg = <0x24 0x20>; - clocks = <&rcc SAI4_K>; - clock-names = "sai_ck"; - dmas = <&dmamux1 100 0x400 0x01>; + vrefbuf: vrefbuf@50025000 { + compatible = "st,stm32-vrefbuf"; + reg = <0x50025000 0x8>; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2500000>; + clocks = <&rcc VREF>; status = "disabled"; }; - };
- dts: thermal@50028000 { - compatible = "st,stm32-thermal"; - reg = <0x50028000 0x100>; - interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc TMPSENS>; - clock-names = "pclk"; - #thermal-sensor-cells = <0>; - status = "disabled"; - }; - - hash1: hash@54002000 { - compatible = "st,stm32f756-hash"; - reg = <0x54002000 0x400>; - interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc HASH1>; - resets = <&rcc HASH1_R>; - dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>; - dma-names = "in"; - dma-maxburst = <2>; - status = "disabled"; - }; - - rng1: rng@54003000 { - compatible = "st,stm32-rng"; - reg = <0x54003000 0x400>; - clocks = <&rcc RNG1_K>; - resets = <&rcc RNG1_R>; - status = "disabled"; - }; - - mdma1: dma-controller@58000000 { - compatible = "st,stm32h7-mdma"; - reg = <0x58000000 0x1000>; - interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc MDMA>; - resets = <&rcc MDMA_R>; - #dma-cells = <5>; - dma-channels = <32>; - dma-requests = <48>; - }; + sai4: sai@50027000 { + compatible = "st,stm32h7-sai"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x50027000 0x400>; + reg = <0x50027000 0x4>, <0x500273f0 0x10>; + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + resets = <&rcc SAI4_R>; + status = "disabled"; + + sai4a: audio-controller@50027004 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-a"; + reg = <0x04 0x20>; + clocks = <&rcc SAI4_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 99 0x400 0x01>; + status = "disabled"; + };
- fmc: memory-controller@58002000 { - #address-cells = <2>; - #size-cells = <1>; - compatible = "st,stm32mp1-fmc2-ebi"; - reg = <0x58002000 0x1000>; - clocks = <&rcc FMC_K>; - resets = <&rcc FMC_R>; - status = "disabled"; + sai4b: audio-controller@50027024 { + #sound-dai-cells = <0>; + compatible = "st,stm32-sai-sub-b"; + reg = <0x24 0x20>; + clocks = <&rcc SAI4_K>; + clock-names = "sai_ck"; + dmas = <&dmamux1 100 0x400 0x01>; + status = "disabled"; + }; + };
- ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ - <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ - <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ - <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ - <4 0 0x80000000 0x10000000>; /* NAND */ + hash1: hash@54002000 { + compatible = "st,stm32f756-hash"; + reg = <0x54002000 0x400>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc HASH1>; + resets = <&rcc HASH1_R>; + dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>; + dma-names = "in"; + dma-maxburst = <2>; + status = "disabled"; + }; + + rng1: rng@54003000 { + compatible = "st,stm32-rng"; + reg = <0x54003000 0x400>; + clocks = <&rcc RNG1_K>; + resets = <&rcc RNG1_R>; + status = "okay"; + }; + + fmc: memory-controller@58002000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "st,stm32mp1-fmc2-ebi"; + reg = <0x58002000 0x1000>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + status = "disabled"; + + ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ + <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ + <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ + <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ + <4 0 0x80000000 0x10000000>; /* NAND */ + + nand-controller@4,0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32mp1-fmc2-nfc"; + reg = <4 0x00000000 0x1000>, + <4 0x08010000 0x1000>, + <4 0x08020000 0x1000>, + <4 0x01000000 0x1000>, + <4 0x09010000 0x1000>, + <4 0x09020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, + <&mdma1 20 0x2 0x12000a08 0x0 0x0>, + <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + status = "disabled"; + }; + };
- nand-controller@4,0 { + qspi: spi@58003000 { + compatible = "st,stm32f469-qspi"; + reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>, + <&mdma1 22 0x2 0x10100008 0x0 0x0>; + dma-names = "tx", "rx"; + clocks = <&rcc QSPI_K>; + resets = <&rcc QSPI_R>; #address-cells = <1>; #size-cells = <0>; - compatible = "st,stm32mp1-fmc2-nfc"; - reg = <4 0x00000000 0x1000>, - <4 0x08010000 0x1000>, - <4 0x08020000 0x1000>, - <4 0x01000000 0x1000>, - <4 0x09010000 0x1000>, - <4 0x09020000 0x1000>; - interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, - <&mdma1 20 0x2 0x12000a08 0x0 0x0>, - <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; - dma-names = "tx", "rx", "ecc"; status = "disabled"; }; - }; - - qspi: spi@58003000 { - compatible = "st,stm32f469-qspi"; - reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; - reg-names = "qspi", "qspi_mm"; - interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>, - <&mdma1 22 0x2 0x10100008 0x0 0x0>; - dma-names = "tx", "rx"; - clocks = <&rcc QSPI_K>; - resets = <&rcc QSPI_R>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - sdmmc1: mmc@58005000 { - compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00253180>; - reg = <0x58005000 0x1000>; - interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SDMMC1_K>; - clock-names = "apb_pclk"; - resets = <&rcc SDMMC1_R>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <120000000>; - status = "disabled"; - };
- sdmmc2: mmc@58007000 { - compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x00253180>; - reg = <0x58007000 0x1000>; - interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SDMMC2_K>; - clock-names = "apb_pclk"; - resets = <&rcc SDMMC2_R>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <120000000>; - status = "disabled"; - }; - - crc1: crc@58009000 { - compatible = "st,stm32f7-crc"; - reg = <0x58009000 0x400>; - clocks = <&rcc CRC1>; - status = "disabled"; - }; - - ethernet0: ethernet@5800a000 { - compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a"; - reg = <0x5800a000 0x2000>; - reg-names = "stmmaceth"; - interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "macirq"; - clock-names = "stmmaceth", - "mac-clk-tx", - "mac-clk-rx", - "eth-ck", - "ptp_ref", - "ethstp"; - clocks = <&rcc ETHMAC>, - <&rcc ETHTX>, - <&rcc ETHRX>, - <&rcc ETHCK_K>, - <&rcc ETHPTP_K>, - <&rcc ETHSTP>; - st,syscon = <&syscfg 0x4>; - snps,mixed-burst; - snps,pbl = <2>; - snps,en-tx-lpi-clockgating; - snps,axi-config = <&stmmac_axi_config_0>; - snps,tso; - status = "disabled"; - - stmmac_axi_config_0: stmmac-axi-config { - snps,wr_osr_lmt = <0x7>; - snps,rd_osr_lmt = <0x7>; - snps,blen = <0 0 0 0 16 8 4>; + ethernet0: ethernet@5800a000 { + compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a"; + reg = <0x5800a000 0x2000>; + reg-names = "stmmaceth"; + interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + clock-names = "stmmaceth", + "mac-clk-tx", + "mac-clk-rx", + "eth-ck", + "ptp_ref", + "ethstp"; + clocks = <&rcc ETHMAC>, + <&rcc ETHTX>, + <&rcc ETHRX>, + <&rcc ETHCK_K>, + <&rcc ETHPTP_K>, + <&rcc ETHSTP>; + st,syscon = <&syscfg 0x4>; + snps,mixed-burst; + snps,pbl = <2>; + snps,en-tx-lpi-clockgating; + snps,axi-config = <&stmmac_axi_config_0>; + snps,tso; + status = "disabled"; + + stmmac_axi_config_0: stmmac-axi-config { + snps,wr_osr_lmt = <0x7>; + snps,rd_osr_lmt = <0x7>; + snps,blen = <0 0 0 0 16 8 4>; + }; }; - }; - - usbh_ohci: usb@5800c000 { - compatible = "generic-ohci"; - reg = <0x5800c000 0x1000>; - clocks = <&usbphyc>, <&rcc USBH>; - resets = <&rcc USBH_R>; - interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - usbh_ehci: usb@5800d000 { - compatible = "generic-ehci"; - reg = <0x5800d000 0x1000>; - clocks = <&usbphyc>, <&rcc USBH>; - resets = <&rcc USBH_R>; - interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - companion = <&usbh_ohci>; - status = "disabled"; - }; - - ltdc: display-controller@5a001000 { - compatible = "st,stm32-ltdc"; - reg = <0x5a001000 0x400>; - interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LTDC_PX>; - clock-names = "lcd"; - resets = <&rcc LTDC_R>; - status = "disabled"; - }; - - iwdg2: watchdog@5a002000 { - compatible = "st,stm32mp1-iwdg"; - reg = <0x5a002000 0x400>; - clocks = <&rcc IWDG2>, <&rcc CK_LSI>; - clock-names = "pclk", "lsi"; - status = "disabled"; - }; - - usbphyc: usbphyc@5a006000 { - #address-cells = <1>; - #size-cells = <0>; - #clock-cells = <0>; - compatible = "st,stm32mp1-usbphyc"; - reg = <0x5a006000 0x1000>; - clocks = <&rcc USBPHY_K>; - resets = <&rcc USBPHY_R>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; - status = "disabled";
- usbphyc_port0: usb-phy@0 { - #phy-cells = <0>; - reg = <0>; + usart1: serial@5c000000 { + compatible = "st,stm32h7-uart"; + reg = <0x5c000000 0x400>; + interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART1_K>; + wakeup-source; + status = "disabled"; };
- usbphyc_port1: usb-phy@1 { - #phy-cells = <1>; - reg = <1>; + spi6: spi@5c001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32h7-spi"; + reg = <0x5c001000 0x400>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI6_K>; + resets = <&rcc SPI6_R>; + dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>, + <&mdma1 35 0x0 0x40002 0x0 0x0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2c4: i2c@5c002000 { + compatible = "st,stm32mp15-i2c"; + reg = <0x5c002000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C4_K>; + resets = <&rcc I2C4_R>; + #address-cells = <1>; + #size-cells = <0>; + st,syscfg-fmp = <&syscfg 0x4 0x8>; + wakeup-source; + i2c-analog-filter; + status = "disabled"; }; - };
- usart1: serial@5c000000 { - compatible = "st,stm32h7-uart"; - reg = <0x5c000000 0x400>; - interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc USART1_K>; - wakeup-source; - status = "disabled"; - }; - - spi6: spi@5c001000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32h7-spi"; - reg = <0x5c001000 0x400>; - interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI6_K>; - resets = <&rcc SPI6_R>; - dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>, - <&mdma1 35 0x0 0x40002 0x0 0x0>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - i2c4: i2c@5c002000 { - compatible = "st,stm32mp15-i2c"; - reg = <0x5c002000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C4_K>; - resets = <&rcc I2C4_R>; - #address-cells = <1>; - #size-cells = <0>; - st,syscfg-fmp = <&syscfg 0x4 0x8>; - wakeup-source; - i2c-analog-filter; - status = "disabled"; - }; - - rtc: rtc@5c004000 { - compatible = "st,stm32mp1-rtc"; - reg = <0x5c004000 0x400>; - clocks = <&rcc RTCAPB>, <&rcc RTC>; - clock-names = "pclk", "rtc_ck"; - interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - bsec: efuse@5c005000 { - compatible = "st,stm32mp15-bsec"; - reg = <0x5c005000 0x400>; - #address-cells = <1>; - #size-cells = <1>; - part_number_otp: part-number-otp@4 { - reg = <0x4 0x1>; - }; - vrefint: vrefin-cal@52 { - reg = <0x52 0x2>; - }; - ts_cal1: calib@5c { - reg = <0x5c 0x2>; - }; - ts_cal2: calib@5e { - reg = <0x5e 0x2>; + i2c6: i2c@5c009000 { + compatible = "st,stm32mp15-i2c"; + reg = <0x5c009000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C6_K>; + resets = <&rcc I2C6_R>; + #address-cells = <1>; + #size-cells = <0>; + st,syscfg-fmp = <&syscfg 0x4 0x20>; + wakeup-source; + i2c-analog-filter; + status = "disabled"; }; };
- i2c6: i2c@5c009000 { - compatible = "st,stm32mp15-i2c"; - reg = <0x5c009000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C6_K>; - resets = <&rcc I2C6_R>; - #address-cells = <1>; - #size-cells = <0>; - st,syscfg-fmp = <&syscfg 0x4 0x20>; - wakeup-source; - i2c-analog-filter; - status = "disabled"; - }; - tamp: tamp@5c00a000 { compatible = "st,stm32-tamp", "syscon", "simple-mfd"; reg = <0x5c00a000 0x400>; diff --git a/arch/arm/boot/dts/st/stm32mp153.dtsi b/arch/arm/boot/dts/st/stm32mp153.dtsi index 486084e0b80b..36e17ea0b179 100644 --- a/arch/arm/boot/dts/st/stm32mp153.dtsi +++ b/arch/arm/boot/dts/st/stm32mp153.dtsi @@ -28,32 +28,32 @@ timer { <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>; }; +};
- soc { - m_can1: can@4400e000 { - compatible = "bosch,m_can"; - reg = <0x4400e000 0x400>, <0x44011000 0x1400>; - reg-names = "m_can", "message_ram"; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "int0", "int1"; - clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; - clock-names = "hclk", "cclk"; - bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>; - status = "disabled"; - }; +&etzpc { + m_can1: can@4400e000 { + compatible = "bosch,m_can"; + reg = <0x4400e000 0x400>, <0x44011000 0x1400>; + reg-names = "m_can", "message_ram"; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "int0", "int1"; + clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; + clock-names = "hclk", "cclk"; + bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>; + status = "disabled"; + };
- m_can2: can@4400f000 { - compatible = "bosch,m_can"; - reg = <0x4400f000 0x400>, <0x44011000 0x2800>; - reg-names = "m_can", "message_ram"; - interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "int0", "int1"; - clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; - clock-names = "hclk", "cclk"; - bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; - status = "disabled"; - }; + m_can2: can@4400f000 { + compatible = "bosch,m_can"; + reg = <0x4400f000 0x400>, <0x44011000 0x2800>; + reg-names = "m_can", "message_ram"; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "int0", "int1"; + clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; + clock-names = "hclk", "cclk"; + bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/st/stm32mp15xc.dtsi b/arch/arm/boot/dts/st/stm32mp15xc.dtsi index b06a55a2fa18..d36c3457451a 100644 --- a/arch/arm/boot/dts/st/stm32mp15xc.dtsi +++ b/arch/arm/boot/dts/st/stm32mp15xc.dtsi @@ -4,15 +4,13 @@ * Author: Alexandre Torgue alexandre.torgue@st.com for STMicroelectronics. */
-/ { - soc { - cryp1: cryp@54001000 { - compatible = "st,stm32mp1-cryp"; - reg = <0x54001000 0x400>; - interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc CRYP1>; - resets = <&rcc CRYP1_R>; - status = "disabled"; - }; +&etzpc { + cryp1: cryp@54001000 { + compatible = "st,stm32mp1-cryp"; + reg = <0x54001000 0x400>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CRYP1>; + resets = <&rcc CRYP1_R>; + status = "disabled"; }; };
Reference ETZPC as an access-control-provider.
For more information on which peripheral is securable or supports MCU isolation, please read the STM32MP13 reference manual
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Patch not present in V6
arch/arm/boot/dts/st/stm32mp151.dtsi | 66 ++++++++++++++++++++++++++- arch/arm/boot/dts/st/stm32mp153.dtsi | 2 + arch/arm/boot/dts/st/stm32mp15xc.dtsi | 1 + 3 files changed, 68 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/st/stm32mp151.dtsi b/arch/arm/boot/dts/st/stm32mp151.dtsi index 78c0d6ccdb09..8a40df8a097b 100644 --- a/arch/arm/boot/dts/st/stm32mp151.dtsi +++ b/arch/arm/boot/dts/st/stm32mp151.dtsi @@ -330,10 +330,11 @@ ts_cal2: calib@5e { };
etzpc: bus@5c007000 { - compatible = "st,stm32-etzpc"; + compatible = "st,stm32-etzpc", "simple-bus"; reg = <0x5c007000 0x400>; #address-cells = <1>; #size-cells = <1>; + #access-controller-cells = <1>; ranges;
timers2: timer@40000000 { @@ -351,6 +352,7 @@ timers2: timer@40000000 { <&dmamux1 21 0x400 0x1>, <&dmamux1 22 0x400 0x1>; dma-names = "ch1", "ch2", "ch3", "ch4", "up"; + access-controllers = <&etzpc 16>; status = "disabled";
pwm { @@ -387,6 +389,7 @@ timers3: timer@40001000 { <&dmamux1 27 0x400 0x1>, <&dmamux1 28 0x400 0x1>; dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; + access-controllers = <&etzpc 17>; status = "disabled";
pwm { @@ -421,6 +424,7 @@ timers4: timer@40002000 { <&dmamux1 31 0x400 0x1>, <&dmamux1 32 0x400 0x1>; dma-names = "ch1", "ch2", "ch3", "ch4"; + access-controllers = <&etzpc 18>; status = "disabled";
pwm { @@ -457,6 +461,7 @@ timers5: timer@40003000 { <&dmamux1 59 0x400 0x1>, <&dmamux1 60 0x400 0x1>; dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig"; + access-controllers = <&etzpc 19>; status = "disabled";
pwm { @@ -488,6 +493,7 @@ timers6: timer@40004000 { clock-names = "int"; dmas = <&dmamux1 69 0x400 0x1>; dma-names = "up"; + access-controllers = <&etzpc 20>; status = "disabled";
timer@5 { @@ -508,6 +514,7 @@ timers7: timer@40005000 { clock-names = "int"; dmas = <&dmamux1 70 0x400 0x1>; dma-names = "up"; + access-controllers = <&etzpc 21>; status = "disabled";
timer@6 { @@ -526,6 +533,7 @@ timers12: timer@40006000 { interrupt-names = "global"; clocks = <&rcc TIM12_K>; clock-names = "int"; + access-controllers = <&etzpc 22>; status = "disabled";
pwm { @@ -550,6 +558,7 @@ timers13: timer@40007000 { interrupt-names = "global"; clocks = <&rcc TIM13_K>; clock-names = "int"; + access-controllers = <&etzpc 23>; status = "disabled";
pwm { @@ -574,6 +583,7 @@ timers14: timer@40008000 { interrupt-names = "global"; clocks = <&rcc TIM14_K>; clock-names = "int"; + access-controllers = <&etzpc 24>; status = "disabled";
pwm { @@ -598,6 +608,7 @@ lptimer1: timer@40009000 { clocks = <&rcc LPTIM1_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 25>; status = "disabled";
pwm { @@ -626,6 +637,7 @@ i2s2: audio-controller@4000b000 { dmas = <&dmamux1 39 0x400 0x01>, <&dmamux1 40 0x400 0x01>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 27>; status = "disabled"; };
@@ -640,6 +652,7 @@ spi2: spi@4000b000 { dmas = <&dmamux1 39 0x400 0x05>, <&dmamux1 40 0x400 0x05>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 27>; status = "disabled"; };
@@ -651,6 +664,7 @@ i2s3: audio-controller@4000c000 { dmas = <&dmamux1 61 0x400 0x01>, <&dmamux1 62 0x400 0x01>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 28>; status = "disabled"; };
@@ -665,6 +679,7 @@ spi3: spi@4000c000 { dmas = <&dmamux1 61 0x400 0x05>, <&dmamux1 62 0x400 0x05>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 28>; status = "disabled"; };
@@ -678,6 +693,7 @@ spdifrx: audio-controller@4000d000 { dmas = <&dmamux1 93 0x400 0x01>, <&dmamux1 94 0x400 0x01>; dma-names = "rx", "rx-ctrl"; + access-controllers = <&etzpc 29>; status = "disabled"; };
@@ -690,6 +706,7 @@ usart2: serial@4000e000 { dmas = <&dmamux1 43 0x400 0x15>, <&dmamux1 44 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 30>; status = "disabled"; };
@@ -702,6 +719,7 @@ usart3: serial@4000f000 { dmas = <&dmamux1 45 0x400 0x15>, <&dmamux1 46 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 31>; status = "disabled"; };
@@ -714,6 +732,7 @@ uart4: serial@40010000 { dmas = <&dmamux1 63 0x400 0x15>, <&dmamux1 64 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 32>; status = "disabled"; };
@@ -726,6 +745,7 @@ uart5: serial@40011000 { dmas = <&dmamux1 65 0x400 0x15>, <&dmamux1 66 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 33>; status = "disabled"; };
@@ -742,6 +762,7 @@ i2c1: i2c@40012000 { st,syscfg-fmp = <&syscfg 0x4 0x1>; wakeup-source; i2c-analog-filter; + access-controllers = <&etzpc 34>; status = "disabled"; };
@@ -758,6 +779,7 @@ i2c2: i2c@40013000 { st,syscfg-fmp = <&syscfg 0x4 0x2>; wakeup-source; i2c-analog-filter; + access-controllers = <&etzpc 35>; status = "disabled"; };
@@ -774,6 +796,7 @@ i2c3: i2c@40014000 { st,syscfg-fmp = <&syscfg 0x4 0x4>; wakeup-source; i2c-analog-filter; + access-controllers = <&etzpc 36>; status = "disabled"; };
@@ -790,6 +813,7 @@ i2c5: i2c@40015000 { st,syscfg-fmp = <&syscfg 0x4 0x10>; wakeup-source; i2c-analog-filter; + access-controllers = <&etzpc 37>; status = "disabled"; };
@@ -799,6 +823,7 @@ cec: cec@40016000 { interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; clocks = <&rcc CEC_K>, <&rcc CEC>; clock-names = "cec", "hdmi-cec"; + access-controllers = <&etzpc 38>; status = "disabled"; };
@@ -809,6 +834,7 @@ dac: dac@40017000 { clock-names = "pclk"; #address-cells = <1>; #size-cells = <0>; + access-controllers = <&etzpc 39>; status = "disabled";
dac1: dac@1 { @@ -835,6 +861,7 @@ uart7: serial@40018000 { dmas = <&dmamux1 79 0x400 0x15>, <&dmamux1 80 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 40>; status = "disabled"; };
@@ -847,6 +874,7 @@ uart8: serial@40019000 { dmas = <&dmamux1 81 0x400 0x15>, <&dmamux1 82 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 41>; status = "disabled"; };
@@ -871,6 +899,7 @@ timers1: timer@44000000 { <&dmamux1 17 0x400 0x1>; dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com"; + access-controllers = <&etzpc 48>; status = "disabled";
pwm { @@ -912,6 +941,7 @@ timers8: timer@44001000 { <&dmamux1 53 0x400 0x1>; dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com"; + access-controllers = <&etzpc 49>; status = "disabled";
pwm { @@ -941,6 +971,7 @@ usart6: serial@44003000 { dmas = <&dmamux1 71 0x400 0x15>, <&dmamux1 72 0x400 0x11>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 51>; status = "disabled"; };
@@ -952,6 +983,7 @@ i2s1: audio-controller@44004000 { dmas = <&dmamux1 37 0x400 0x01>, <&dmamux1 38 0x400 0x01>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 52>; status = "disabled"; };
@@ -966,6 +998,7 @@ spi1: spi@44004000 { dmas = <&dmamux1 37 0x400 0x05>, <&dmamux1 38 0x400 0x05>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 52>; status = "disabled"; };
@@ -980,6 +1013,7 @@ spi4: spi@44005000 { dmas = <&dmamux1 83 0x400 0x05>, <&dmamux1 84 0x400 0x05>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 53>; status = "disabled"; };
@@ -997,6 +1031,7 @@ timers15: timer@44006000 { <&dmamux1 107 0x400 0x1>, <&dmamux1 108 0x400 0x1>; dma-names = "ch1", "up", "trig", "com"; + access-controllers = <&etzpc 54>; status = "disabled";
pwm { @@ -1024,6 +1059,7 @@ timers16: timer@44007000 { dmas = <&dmamux1 109 0x400 0x1>, <&dmamux1 110 0x400 0x1>; dma-names = "ch1", "up"; + access-controllers = <&etzpc 55>; status = "disabled";
pwm { @@ -1050,6 +1086,7 @@ timers17: timer@44008000 { dmas = <&dmamux1 111 0x400 0x1>, <&dmamux1 112 0x400 0x1>; dma-names = "ch1", "up"; + access-controllers = <&etzpc 56>; status = "disabled";
pwm { @@ -1076,6 +1113,7 @@ spi5: spi@44009000 { dmas = <&dmamux1 85 0x400 0x05>, <&dmamux1 86 0x400 0x05>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 57>; status = "disabled"; };
@@ -1087,6 +1125,7 @@ sai1: sai@4400a000 { reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>; interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; resets = <&rcc SAI1_R>; + access-controllers = <&etzpc 58>; status = "disabled";
sai1a: audio-controller@4400a004 { @@ -1119,6 +1158,7 @@ sai2: sai@4400b000 { reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>; interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; resets = <&rcc SAI2_R>; + access-controllers = <&etzpc 59>; status = "disabled";
sai2a: audio-controller@4400b004 { @@ -1150,6 +1190,7 @@ sai3: sai@4400c000 { reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>; interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; resets = <&rcc SAI3_R>; + access-controllers = <&etzpc 60>; status = "disabled";
sai3a: audio-controller@4400c004 { @@ -1180,6 +1221,7 @@ dfsdm: dfsdm@4400d000 { clock-names = "dfsdm"; #address-cells = <1>; #size-cells = <0>; + access-controllers = <&etzpc 61>; status = "disabled";
dfsdm0: filter@0 { @@ -1259,6 +1301,7 @@ dma1: dma-controller@48000000 { #dma-cells = <4>; st,mem2mem; dma-requests = <8>; + access-controllers = <&etzpc 88>; };
dma2: dma-controller@48001000 { @@ -1277,6 +1320,7 @@ dma2: dma-controller@48001000 { #dma-cells = <4>; st,mem2mem; dma-requests = <8>; + access-controllers = <&etzpc 89>; };
dmamux1: dma-router@48002000 { @@ -1288,6 +1332,7 @@ dmamux1: dma-router@48002000 { dma-channels = <16>; clocks = <&rcc DMAMUX>; resets = <&rcc DMAMUX_R>; + access-controllers = <&etzpc 90>; };
adc: adc@48003000 { @@ -1302,6 +1347,7 @@ adc: adc@48003000 { #interrupt-cells = <1>; #address-cells = <1>; #size-cells = <0>; + access-controllers = <&etzpc 72>; status = "disabled";
adc1: adc@0 { @@ -1352,6 +1398,7 @@ sdmmc3: mmc@48004000 { cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <120000000>; + access-controllers = <&etzpc 86>; status = "disabled"; };
@@ -1369,6 +1416,7 @@ usbotg_hs: usb-otg@49000000 { dr_mode = "otg"; otg-rev = <0x200>; usb33d-supply = <&usb33>; + access-controllers = <&etzpc 85>; status = "disabled"; };
@@ -1381,6 +1429,7 @@ dcmi: dcmi@4c006000 { clock-names = "mclk"; dmas = <&dmamux1 75 0x400 0x01>; dma-names = "tx"; + access-controllers = <&etzpc 70>; status = "disabled"; };
@@ -1393,6 +1442,7 @@ lptimer2: timer@50021000 { clocks = <&rcc LPTIM2_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 64>; status = "disabled";
pwm { @@ -1422,6 +1472,7 @@ lptimer3: timer@50022000 { clocks = <&rcc LPTIM3_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 65>; status = "disabled";
pwm { @@ -1444,6 +1495,7 @@ lptimer4: timer@50023000 { clocks = <&rcc LPTIM4_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 66>; status = "disabled";
pwm { @@ -1460,6 +1512,7 @@ lptimer5: timer@50024000 { clocks = <&rcc LPTIM5_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 67>; status = "disabled";
pwm { @@ -1475,6 +1528,7 @@ vrefbuf: vrefbuf@50025000 { regulator-min-microvolt = <1500000>; regulator-max-microvolt = <2500000>; clocks = <&rcc VREF>; + access-controllers = <&etzpc 69>; status = "disabled"; };
@@ -1486,6 +1540,7 @@ sai4: sai@50027000 { reg = <0x50027000 0x4>, <0x500273f0 0x10>; interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; resets = <&rcc SAI4_R>; + access-controllers = <&etzpc 68>; status = "disabled";
sai4a: audio-controller@50027004 { @@ -1518,6 +1573,7 @@ hash1: hash@54002000 { dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>; dma-names = "in"; dma-maxburst = <2>; + access-controllers = <&etzpc 8>; status = "disabled"; };
@@ -1526,6 +1582,7 @@ rng1: rng@54003000 { reg = <0x54003000 0x400>; clocks = <&rcc RNG1_K>; resets = <&rcc RNG1_R>; + access-controllers = <&etzpc 7>; status = "okay"; };
@@ -1536,6 +1593,7 @@ fmc: memory-controller@58002000 { reg = <0x58002000 0x1000>; clocks = <&rcc FMC_K>; resets = <&rcc FMC_R>; + access-controllers = <&etzpc 91>; status = "disabled";
ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ @@ -1575,6 +1633,7 @@ qspi: spi@58003000 { resets = <&rcc QSPI_R>; #address-cells = <1>; #size-cells = <0>; + access-controllers = <&etzpc 92>; status = "disabled"; };
@@ -1602,6 +1661,7 @@ ethernet0: ethernet@5800a000 { snps,en-tx-lpi-clockgating; snps,axi-config = <&stmmac_axi_config_0>; snps,tso; + access-controllers = <&etzpc 94>; status = "disabled";
stmmac_axi_config_0: stmmac-axi-config { @@ -1617,6 +1677,7 @@ usart1: serial@5c000000 { interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&rcc USART1_K>; wakeup-source; + access-controllers = <&etzpc 3>; status = "disabled"; };
@@ -1630,6 +1691,7 @@ spi6: spi@5c001000 { resets = <&rcc SPI6_R>; dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>, <&mdma1 35 0x0 0x40002 0x0 0x0>; + access-controllers = <&etzpc 4>; dma-names = "rx", "tx"; status = "disabled"; }; @@ -1647,6 +1709,7 @@ i2c4: i2c@5c002000 { st,syscfg-fmp = <&syscfg 0x4 0x8>; wakeup-source; i2c-analog-filter; + access-controllers = <&etzpc 5>; status = "disabled"; };
@@ -1663,6 +1726,7 @@ i2c6: i2c@5c009000 { st,syscfg-fmp = <&syscfg 0x4 0x20>; wakeup-source; i2c-analog-filter; + access-controllers = <&etzpc 12>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/st/stm32mp153.dtsi b/arch/arm/boot/dts/st/stm32mp153.dtsi index 36e17ea0b179..4640dafb1598 100644 --- a/arch/arm/boot/dts/st/stm32mp153.dtsi +++ b/arch/arm/boot/dts/st/stm32mp153.dtsi @@ -41,6 +41,7 @@ m_can1: can@4400e000 { clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; clock-names = "hclk", "cclk"; bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>; + access-controllers = <&etzpc 62>; status = "disabled"; };
@@ -54,6 +55,7 @@ m_can2: can@4400f000 { clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>; clock-names = "hclk", "cclk"; bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; + access-controllers = <&etzpc 62>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/st/stm32mp15xc.dtsi b/arch/arm/boot/dts/st/stm32mp15xc.dtsi index d36c3457451a..97465717f932 100644 --- a/arch/arm/boot/dts/st/stm32mp15xc.dtsi +++ b/arch/arm/boot/dts/st/stm32mp15xc.dtsi @@ -11,6 +11,7 @@ cryp1: cryp@54001000 { interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; clocks = <&rcc CRYP1>; resets = <&rcc CRYP1_R>; + access-controllers = <&etzpc 9>; status = "disabled"; }; };
ETZPC is a firewall controller. Put all peripherals filtered by the ETZPC as ETZPC subnodes and keep the "simple-bus" compatible for backward compatibility.
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Changes in V7: - Keep simple-bus compatible - Remove access-controllers reference in this patch
Changes in V6: - Renamed access-controller to access-controllers - Removal of access-control-provider property
Changes in V5: - Renamed feature-domain* to access-control*
arch/arm/boot/dts/st/stm32mp131.dtsi | 1037 +++++++++++++------------ arch/arm/boot/dts/st/stm32mp133.dtsi | 50 +- arch/arm/boot/dts/st/stm32mp13xc.dtsi | 18 +- arch/arm/boot/dts/st/stm32mp13xf.dtsi | 18 +- 4 files changed, 564 insertions(+), 559 deletions(-)
diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi index b04d24c939c3..6ba8e3fd43b0 100644 --- a/arch/arm/boot/dts/st/stm32mp131.dtsi +++ b/arch/arm/boot/dts/st/stm32mp131.dtsi @@ -745,340 +745,6 @@ dmamux1: dma-router@48002000 { dma-channels = <16>; };
- adc_2: adc@48004000 { - compatible = "st,stm32mp13-adc-core"; - reg = <0x48004000 0x400>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc ADC2>, <&rcc ADC2_K>; - clock-names = "bus", "adc"; - interrupt-controller; - #interrupt-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - adc2: adc@0 { - compatible = "st,stm32mp13-adc"; - #io-channel-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0>; - interrupt-parent = <&adc_2>; - interrupts = <0>; - dmas = <&dmamux1 10 0x400 0x80000001>; - dma-names = "rx"; - status = "disabled"; - - channel@13 { - reg = <13>; - label = "vrefint"; - }; - channel@14 { - reg = <14>; - label = "vddcore"; - }; - channel@16 { - reg = <16>; - label = "vddcpu"; - }; - channel@17 { - reg = <17>; - label = "vddq_ddr"; - }; - }; - }; - - usbotg_hs: usb@49000000 { - compatible = "st,stm32mp15-hsotg", "snps,dwc2"; - reg = <0x49000000 0x40000>; - clocks = <&rcc USBO_K>; - clock-names = "otg"; - resets = <&rcc USBO_R>; - reset-names = "dwc2"; - interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; - g-rx-fifo-size = <512>; - g-np-tx-fifo-size = <32>; - g-tx-fifo-size = <256 16 16 16 16 16 16 16>; - dr_mode = "otg"; - otg-rev = <0x200>; - usb33d-supply = <&scmi_usb33>; - status = "disabled"; - }; - - usart1: serial@4c000000 { - compatible = "st,stm32h7-uart"; - reg = <0x4c000000 0x400>; - interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc USART1_K>; - resets = <&rcc USART1_R>; - wakeup-source; - dmas = <&dmamux1 41 0x400 0x5>, - <&dmamux1 42 0x400 0x1>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - usart2: serial@4c001000 { - compatible = "st,stm32h7-uart"; - reg = <0x4c001000 0x400>; - interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc USART2_K>; - resets = <&rcc USART2_R>; - wakeup-source; - dmas = <&dmamux1 43 0x400 0x5>, - <&dmamux1 44 0x400 0x1>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - i2s4: audio-controller@4c002000 { - compatible = "st,stm32h7-i2s"; - reg = <0x4c002000 0x400>; - #sound-dai-cells = <0>; - interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&dmamux1 83 0x400 0x01>, - <&dmamux1 84 0x400 0x01>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - spi4: spi@4c002000 { - compatible = "st,stm32h7-spi"; - reg = <0x4c002000 0x400>; - interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI4_K>; - resets = <&rcc SPI4_R>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmamux1 83 0x400 0x01>, - <&dmamux1 84 0x400 0x01>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - spi5: spi@4c003000 { - compatible = "st,stm32h7-spi"; - reg = <0x4c003000 0x400>; - interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SPI5_K>; - resets = <&rcc SPI5_R>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmamux1 85 0x400 0x01>, - <&dmamux1 86 0x400 0x01>; - dma-names = "rx", "tx"; - status = "disabled"; - }; - - i2c3: i2c@4c004000 { - compatible = "st,stm32mp13-i2c"; - reg = <0x4c004000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C3_K>; - resets = <&rcc I2C3_R>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmamux1 73 0x400 0x1>, - <&dmamux1 74 0x400 0x1>; - dma-names = "rx", "tx"; - st,syscfg-fmp = <&syscfg 0x4 0x4>; - i2c-analog-filter; - status = "disabled"; - }; - - i2c4: i2c@4c005000 { - compatible = "st,stm32mp13-i2c"; - reg = <0x4c005000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C4_K>; - resets = <&rcc I2C4_R>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmamux1 75 0x400 0x1>, - <&dmamux1 76 0x400 0x1>; - dma-names = "rx", "tx"; - st,syscfg-fmp = <&syscfg 0x4 0x8>; - i2c-analog-filter; - status = "disabled"; - }; - - i2c5: i2c@4c006000 { - compatible = "st,stm32mp13-i2c"; - reg = <0x4c006000 0x400>; - interrupt-names = "event", "error"; - interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc I2C5_K>; - resets = <&rcc I2C5_R>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmamux1 115 0x400 0x1>, - <&dmamux1 116 0x400 0x1>; - dma-names = "rx", "tx"; - st,syscfg-fmp = <&syscfg 0x4 0x10>; - i2c-analog-filter; - status = "disabled"; - }; - - timers12: timer@4c007000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x4c007000 0x400>; - interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM12_K>; - clock-names = "int"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@11 { - compatible = "st,stm32h7-timer-trigger"; - reg = <11>; - status = "disabled"; - }; - }; - - timers13: timer@4c008000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x4c008000 0x400>; - interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM13_K>; - clock-names = "int"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@12 { - compatible = "st,stm32h7-timer-trigger"; - reg = <12>; - status = "disabled"; - }; - }; - - timers14: timer@4c009000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x4c009000 0x400>; - interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM14_K>; - clock-names = "int"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@13 { - compatible = "st,stm32h7-timer-trigger"; - reg = <13>; - status = "disabled"; - }; - }; - - timers15: timer@4c00a000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x4c00a000 0x400>; - interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM15_K>; - clock-names = "int"; - dmas = <&dmamux1 105 0x400 0x1>, - <&dmamux1 106 0x400 0x1>, - <&dmamux1 107 0x400 0x1>, - <&dmamux1 108 0x400 0x1>; - dma-names = "ch1", "up", "trig", "com"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@14 { - compatible = "st,stm32h7-timer-trigger"; - reg = <14>; - status = "disabled"; - }; - }; - - timers16: timer@4c00b000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x4c00b000 0x400>; - interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM16_K>; - clock-names = "int"; - dmas = <&dmamux1 109 0x400 0x1>, - <&dmamux1 110 0x400 0x1>; - dma-names = "ch1", "up"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@15 { - compatible = "st,stm32h7-timer-trigger"; - reg = <15>; - status = "disabled"; - }; - }; - - timers17: timer@4c00c000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-timers"; - reg = <0x4c00c000 0x400>; - interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "global"; - clocks = <&rcc TIM17_K>; - clock-names = "int"; - dmas = <&dmamux1 111 0x400 0x1>, - <&dmamux1 112 0x400 0x1>; - dma-names = "ch1", "up"; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm"; - #pwm-cells = <3>; - status = "disabled"; - }; - - timer@16 { - compatible = "st,stm32h7-timer-trigger"; - reg = <16>; - status = "disabled"; - }; - }; - rcc: rcc@50000000 { compatible = "st,stm32mp13-rcc", "syscon"; reg = <0x50000000 0x1000>; @@ -1105,69 +771,6 @@ syscfg: syscon@50020000 { clocks = <&rcc SYSCFG>; };
- lptimer2: timer@50021000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-lptimer"; - reg = <0x50021000 0x400>; - interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM2_K>; - clock-names = "mux"; - wakeup-source; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; - status = "disabled"; - }; - - trigger@1 { - compatible = "st,stm32-lptimer-trigger"; - reg = <1>; - status = "disabled"; - }; - - counter { - compatible = "st,stm32-lptimer-counter"; - status = "disabled"; - }; - - timer { - compatible = "st,stm32-lptimer-timer"; - status = "disabled"; - }; - }; - - lptimer3: timer@50022000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "st,stm32-lptimer"; - reg = <0x50022000 0x400>; - interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc LPTIM3_K>; - clock-names = "mux"; - wakeup-source; - status = "disabled"; - - pwm { - compatible = "st,stm32-pwm-lp"; - #pwm-cells = <3>; - status = "disabled"; - }; - - trigger@2 { - compatible = "st,stm32-lptimer-trigger"; - reg = <2>; - status = "disabled"; - }; - - timer { - compatible = "st,stm32-lptimer-timer"; - status = "disabled"; - }; - }; - lptimer4: timer@50023000 { compatible = "st,stm32-lptimer"; reg = <0x50023000 0x400>; @@ -1210,25 +813,6 @@ timer { }; };
- hash: hash@54003000 { - compatible = "st,stm32mp13-hash"; - reg = <0x54003000 0x400>; - interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc HASH1>; - resets = <&rcc HASH1_R>; - dmas = <&mdma 30 0x2 0x1000a02 0x0 0x0>; - dma-names = "in"; - status = "disabled"; - }; - - rng: rng@54004000 { - compatible = "st,stm32mp13-rng"; - reg = <0x54004000 0x400>; - clocks = <&rcc RNG1_K>; - resets = <&rcc RNG1_R>; - status = "disabled"; - }; - mdma: dma-controller@58000000 { compatible = "st,stm32h7-mdma"; reg = <0x58000000 0x1000>; @@ -1239,82 +823,6 @@ mdma: dma-controller@58000000 { dma-requests = <48>; };
- fmc: memory-controller@58002000 { - compatible = "st,stm32mp1-fmc2-ebi"; - reg = <0x58002000 0x1000>; - ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ - <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ - <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ - <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ - <4 0 0x80000000 0x10000000>; /* NAND */ - #address-cells = <2>; - #size-cells = <1>; - clocks = <&rcc FMC_K>; - resets = <&rcc FMC_R>; - status = "disabled"; - - nand-controller@4,0 { - compatible = "st,stm32mp1-fmc2-nfc"; - reg = <4 0x00000000 0x1000>, - <4 0x08010000 0x1000>, - <4 0x08020000 0x1000>, - <4 0x01000000 0x1000>, - <4 0x09010000 0x1000>, - <4 0x09020000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>, - <&mdma 24 0x2 0x12000a08 0x0 0x0>, - <&mdma 25 0x2 0x12000a0a 0x0 0x0>; - dma-names = "tx", "rx", "ecc"; - status = "disabled"; - }; - }; - - qspi: spi@58003000 { - compatible = "st,stm32f469-qspi"; - reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; - reg-names = "qspi", "qspi_mm"; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>, - <&mdma 26 0x2 0x10100008 0x0 0x0>; - dma-names = "tx", "rx"; - clocks = <&rcc QSPI_K>; - resets = <&rcc QSPI_R>; - status = "disabled"; - }; - - sdmmc1: mmc@58005000 { - compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x20253180>; - reg = <0x58005000 0x1000>, <0x58006000 0x1000>; - interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SDMMC1_K>; - clock-names = "apb_pclk"; - resets = <&rcc SDMMC1_R>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <130000000>; - status = "disabled"; - }; - - sdmmc2: mmc@58007000 { - compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; - arm,primecell-periphid = <0x20253180>; - reg = <0x58007000 0x1000>, <0x58008000 0x1000>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc SDMMC2_K>; - clock-names = "apb_pclk"; - resets = <&rcc SDMMC2_R>; - cap-sd-highspeed; - cap-mmc-highspeed; - max-frequency = <130000000>; - status = "disabled"; - }; - usbh_ohci: usb@5800c000 { compatible = "generic-ohci"; reg = <0x5800c000 0x1000>; @@ -1342,29 +850,6 @@ iwdg2: watchdog@5a002000 { status = "disabled"; };
- usbphyc: usbphyc@5a006000 { - #address-cells = <1>; - #size-cells = <0>; - #clock-cells = <0>; - compatible = "st,stm32mp1-usbphyc"; - reg = <0x5a006000 0x1000>; - clocks = <&rcc USBPHY_K>; - resets = <&rcc USBPHY_R>; - vdda1v1-supply = <&scmi_reg11>; - vdda1v8-supply = <&scmi_reg18>; - status = "disabled"; - - usbphyc_port0: usb-phy@0 { - #phy-cells = <0>; - reg = <0>; - }; - - usbphyc_port1: usb-phy@1 { - #phy-cells = <1>; - reg = <1>; - }; - }; - rtc: rtc@5c004000 { compatible = "st,stm32mp1-rtc"; reg = <0x5c004000 0x400>; @@ -1393,6 +878,527 @@ ts_cal2: calib@5e { }; };
+ etzpc: bus@5c007000 { + compatible = "st,stm32-etzpc", "simple-bus"; + reg = <0x5c007000 0x400>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + adc_2: adc@48004000 { + compatible = "st,stm32mp13-adc-core"; + reg = <0x48004000 0x400>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc ADC2>, <&rcc ADC2_K>; + clock-names = "bus", "adc"; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + adc2: adc@0 { + compatible = "st,stm32mp13-adc"; + #io-channel-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + interrupt-parent = <&adc_2>; + interrupts = <0>; + dmas = <&dmamux1 10 0x400 0x80000001>; + dma-names = "rx"; + status = "disabled"; + + channel@13 { + reg = <13>; + label = "vrefint"; + }; + channel@14 { + reg = <14>; + label = "vddcore"; + }; + channel@16 { + reg = <16>; + label = "vddcpu"; + }; + channel@17 { + reg = <17>; + label = "vddq_ddr"; + }; + }; + }; + + usbotg_hs: usb@49000000 { + compatible = "st,stm32mp15-hsotg", "snps,dwc2"; + reg = <0x49000000 0x40000>; + clocks = <&rcc USBO_K>; + clock-names = "otg"; + resets = <&rcc USBO_R>; + reset-names = "dwc2"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + g-rx-fifo-size = <512>; + g-np-tx-fifo-size = <32>; + g-tx-fifo-size = <256 16 16 16 16 16 16 16>; + dr_mode = "otg"; + otg-rev = <0x200>; + usb33d-supply = <&scmi_usb33>; + status = "disabled"; + }; + + usart1: serial@4c000000 { + compatible = "st,stm32h7-uart"; + reg = <0x4c000000 0x400>; + interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART1_K>; + resets = <&rcc USART1_R>; + wakeup-source; + dmas = <&dmamux1 41 0x400 0x5>, + <&dmamux1 42 0x400 0x1>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + usart2: serial@4c001000 { + compatible = "st,stm32h7-uart"; + reg = <0x4c001000 0x400>; + interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc USART2_K>; + resets = <&rcc USART2_R>; + wakeup-source; + dmas = <&dmamux1 43 0x400 0x5>, + <&dmamux1 44 0x400 0x1>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2s4: audio-controller@4c002000 { + compatible = "st,stm32h7-i2s"; + reg = <0x4c002000 0x400>; + #sound-dai-cells = <0>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dmamux1 83 0x400 0x01>, + <&dmamux1 84 0x400 0x01>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + spi4: spi@4c002000 { + compatible = "st,stm32h7-spi"; + reg = <0x4c002000 0x400>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI4_K>; + resets = <&rcc SPI4_R>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmamux1 83 0x400 0x01>, + <&dmamux1 84 0x400 0x01>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + spi5: spi@4c003000 { + compatible = "st,stm32h7-spi"; + reg = <0x4c003000 0x400>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SPI5_K>; + resets = <&rcc SPI5_R>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmamux1 85 0x400 0x01>, + <&dmamux1 86 0x400 0x01>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2c3: i2c@4c004000 { + compatible = "st,stm32mp13-i2c"; + reg = <0x4c004000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C3_K>; + resets = <&rcc I2C3_R>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmamux1 73 0x400 0x1>, + <&dmamux1 74 0x400 0x1>; + dma-names = "rx", "tx"; + st,syscfg-fmp = <&syscfg 0x4 0x4>; + i2c-analog-filter; + status = "disabled"; + }; + + i2c4: i2c@4c005000 { + compatible = "st,stm32mp13-i2c"; + reg = <0x4c005000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C4_K>; + resets = <&rcc I2C4_R>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmamux1 75 0x400 0x1>, + <&dmamux1 76 0x400 0x1>; + dma-names = "rx", "tx"; + st,syscfg-fmp = <&syscfg 0x4 0x8>; + i2c-analog-filter; + status = "disabled"; + }; + + i2c5: i2c@4c006000 { + compatible = "st,stm32mp13-i2c"; + reg = <0x4c006000 0x400>; + interrupt-names = "event", "error"; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc I2C5_K>; + resets = <&rcc I2C5_R>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmamux1 115 0x400 0x1>, + <&dmamux1 116 0x400 0x1>; + dma-names = "rx", "tx"; + st,syscfg-fmp = <&syscfg 0x4 0x10>; + i2c-analog-filter; + status = "disabled"; + }; + + timers12: timer@4c007000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x4c007000 0x400>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM12_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@11 { + compatible = "st,stm32h7-timer-trigger"; + reg = <11>; + status = "disabled"; + }; + }; + + timers13: timer@4c008000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x4c008000 0x400>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM13_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@12 { + compatible = "st,stm32h7-timer-trigger"; + reg = <12>; + status = "disabled"; + }; + }; + + timers14: timer@4c009000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x4c009000 0x400>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM14_K>; + clock-names = "int"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@13 { + compatible = "st,stm32h7-timer-trigger"; + reg = <13>; + status = "disabled"; + }; + }; + + timers15: timer@4c00a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x4c00a000 0x400>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM15_K>; + clock-names = "int"; + dmas = <&dmamux1 105 0x400 0x1>, + <&dmamux1 106 0x400 0x1>, + <&dmamux1 107 0x400 0x1>, + <&dmamux1 108 0x400 0x1>; + dma-names = "ch1", "up", "trig", "com"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@14 { + compatible = "st,stm32h7-timer-trigger"; + reg = <14>; + status = "disabled"; + }; + }; + + timers16: timer@4c00b000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x4c00b000 0x400>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM16_K>; + clock-names = "int"; + dmas = <&dmamux1 109 0x400 0x1>, + <&dmamux1 110 0x400 0x1>; + dma-names = "ch1", "up"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@15 { + compatible = "st,stm32h7-timer-trigger"; + reg = <15>; + status = "disabled"; + }; + }; + + timers17: timer@4c00c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-timers"; + reg = <0x4c00c000 0x400>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "global"; + clocks = <&rcc TIM17_K>; + clock-names = "int"; + dmas = <&dmamux1 111 0x400 0x1>, + <&dmamux1 112 0x400 0x1>; + dma-names = "ch1", "up"; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm"; + #pwm-cells = <3>; + status = "disabled"; + }; + + timer@16 { + compatible = "st,stm32h7-timer-trigger"; + reg = <16>; + status = "disabled"; + }; + }; + + lptimer2: timer@50021000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x50021000 0x400>; + interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM2_K>; + clock-names = "mux"; + wakeup-source; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + + trigger@1 { + compatible = "st,stm32-lptimer-trigger"; + reg = <1>; + status = "disabled"; + }; + + counter { + compatible = "st,stm32-lptimer-counter"; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-lptimer-timer"; + status = "disabled"; + }; + }; + + lptimer3: timer@50022000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32-lptimer"; + reg = <0x50022000 0x400>; + interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc LPTIM3_K>; + clock-names = "mux"; + wakeup-source; + status = "disabled"; + + pwm { + compatible = "st,stm32-pwm-lp"; + #pwm-cells = <3>; + status = "disabled"; + }; + + trigger@2 { + compatible = "st,stm32-lptimer-trigger"; + reg = <2>; + status = "disabled"; + }; + + timer { + compatible = "st,stm32-lptimer-timer"; + status = "disabled"; + }; + }; + + hash: hash@54003000 { + compatible = "st,stm32mp13-hash"; + reg = <0x54003000 0x400>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc HASH1>; + resets = <&rcc HASH1_R>; + dmas = <&mdma 30 0x2 0x1000a02 0x0 0x0>; + dma-names = "in"; + }; + + rng: rng@54004000 { + compatible = "st,stm32mp13-rng"; + reg = <0x54004000 0x400>; + clocks = <&rcc RNG1_K>; + resets = <&rcc RNG1_R>; + }; + + fmc: memory-controller@58002000 { + compatible = "st,stm32mp1-fmc2-ebi"; + reg = <0x58002000 0x1000>; + ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ + <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ + <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ + <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ + <4 0 0x80000000 0x10000000>; /* NAND */ + #address-cells = <2>; + #size-cells = <1>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + status = "disabled"; + + nand-controller@4,0 { + compatible = "st,stm32mp1-fmc2-nfc"; + reg = <4 0x00000000 0x1000>, + <4 0x08010000 0x1000>, + <4 0x08020000 0x1000>, + <4 0x01000000 0x1000>, + <4 0x09010000 0x1000>, + <4 0x09020000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>, + <&mdma 24 0x2 0x12000a08 0x0 0x0>, + <&mdma 25 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + status = "disabled"; + }; + }; + + qspi: spi@58003000 { + compatible = "st,stm32f469-qspi"; + reg = <0x58003000 0x1000>, <0x70000000 0x10000000>; + reg-names = "qspi", "qspi_mm"; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>, + <&mdma 26 0x2 0x10100008 0x0 0x0>; + dma-names = "tx", "rx"; + clocks = <&rcc QSPI_K>; + resets = <&rcc QSPI_R>; + status = "disabled"; + }; + + sdmmc1: mmc@58005000 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x20253180>; + reg = <0x58005000 0x1000>, <0x58006000 0x1000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SDMMC1_K>; + clock-names = "apb_pclk"; + resets = <&rcc SDMMC1_R>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <130000000>; + status = "disabled"; + }; + + sdmmc2: mmc@58007000 { + compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x20253180>; + reg = <0x58007000 0x1000>, <0x58008000 0x1000>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc SDMMC2_K>; + clock-names = "apb_pclk"; + resets = <&rcc SDMMC2_R>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <130000000>; + status = "disabled"; + }; + + usbphyc: usbphyc@5a006000 { + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + compatible = "st,stm32mp1-usbphyc"; + reg = <0x5a006000 0x1000>; + clocks = <&rcc USBPHY_K>; + resets = <&rcc USBPHY_R>; + vdda1v1-supply = <&scmi_reg11>; + vdda1v8-supply = <&scmi_reg18>; + status = "disabled"; + + usbphyc_port0: usb-phy@0 { + #phy-cells = <0>; + reg = <0>; + }; + + usbphyc_port1: usb-phy@1 { + #phy-cells = <1>; + reg = <1>; + }; + }; + }; + /* * Break node order to solve dependency probe issue between * pinctrl and exti. @@ -1404,6 +1410,7 @@ pinctrl: pinctrl@50002000 { ranges = <0 0x50002000 0x8400>; interrupt-parent = <&exti>; st,syscfg = <&exti 0x60 0xff>; + pins-are-numbered;
gpioa: gpio@50002000 { gpio-controller; diff --git a/arch/arm/boot/dts/st/stm32mp133.dtsi b/arch/arm/boot/dts/st/stm32mp133.dtsi index df451c3c2a26..c4d3a520c14b 100644 --- a/arch/arm/boot/dts/st/stm32mp133.dtsi +++ b/arch/arm/boot/dts/st/stm32mp133.dtsi @@ -33,35 +33,37 @@ m_can2: can@4400f000 { bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>; status = "disabled"; }; + }; +};
- adc_1: adc@48003000 { - compatible = "st,stm32mp13-adc-core"; - reg = <0x48003000 0x400>; - interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc ADC1>, <&rcc ADC1_K>; - clock-names = "bus", "adc"; - interrupt-controller; - #interrupt-cells = <1>; +&etzpc { + adc_1: adc@48003000 { + compatible = "st,stm32mp13-adc-core"; + reg = <0x48003000 0x400>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc ADC1>, <&rcc ADC1_K>; + clock-names = "bus", "adc"; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + adc1: adc@0 { + compatible = "st,stm32mp13-adc"; + #io-channel-cells = <1>; #address-cells = <1>; #size-cells = <0>; + reg = <0x0>; + interrupt-parent = <&adc_1>; + interrupts = <0>; + dmas = <&dmamux1 9 0x400 0x80000001>; + dma-names = "rx"; status = "disabled";
- adc1: adc@0 { - compatible = "st,stm32mp13-adc"; - #io-channel-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x0>; - interrupt-parent = <&adc_1>; - interrupts = <0>; - dmas = <&dmamux1 9 0x400 0x80000001>; - dma-names = "rx"; - status = "disabled"; - - channel@18 { - reg = <18>; - label = "vrefint"; - }; + channel@18 { + reg = <18>; + label = "vrefint"; }; }; }; diff --git a/arch/arm/boot/dts/st/stm32mp13xc.dtsi b/arch/arm/boot/dts/st/stm32mp13xc.dtsi index 4d00e7592882..b9fb071a1471 100644 --- a/arch/arm/boot/dts/st/stm32mp13xc.dtsi +++ b/arch/arm/boot/dts/st/stm32mp13xc.dtsi @@ -4,15 +4,13 @@ * Author: Alexandre Torgue alexandre.torgue@foss.st.com for STMicroelectronics. */
-/ { - soc { - cryp: crypto@54002000 { - compatible = "st,stm32mp1-cryp"; - reg = <0x54002000 0x400>; - interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc CRYP1>; - resets = <&rcc CRYP1_R>; - status = "disabled"; - }; +&etzpc { + cryp: crypto@54002000 { + compatible = "st,stm32mp1-cryp"; + reg = <0x54002000 0x400>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CRYP1>; + resets = <&rcc CRYP1_R>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/st/stm32mp13xf.dtsi b/arch/arm/boot/dts/st/stm32mp13xf.dtsi index 4d00e7592882..b9fb071a1471 100644 --- a/arch/arm/boot/dts/st/stm32mp13xf.dtsi +++ b/arch/arm/boot/dts/st/stm32mp13xf.dtsi @@ -4,15 +4,13 @@ * Author: Alexandre Torgue alexandre.torgue@foss.st.com for STMicroelectronics. */
-/ { - soc { - cryp: crypto@54002000 { - compatible = "st,stm32mp1-cryp"; - reg = <0x54002000 0x400>; - interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&rcc CRYP1>; - resets = <&rcc CRYP1_R>; - status = "disabled"; - }; +&etzpc { + cryp: crypto@54002000 { + compatible = "st,stm32mp1-cryp"; + reg = <0x54002000 0x400>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&rcc CRYP1>; + resets = <&rcc CRYP1_R>; + status = "disabled"; }; };
Reference ETZPC as an access-control-provider.
For more information on which peripheral is securable or supports MCU isolation, please read the STM32MP13 reference manual
Signed-off-by: Gatien Chevallier gatien.chevallier@foss.st.com ---
Patch not present in V6
arch/arm/boot/dts/st/stm32mp131.dtsi | 26 ++++++++++++++++++++++++++ arch/arm/boot/dts/st/stm32mp133.dtsi | 1 + arch/arm/boot/dts/st/stm32mp13xc.dtsi | 1 + arch/arm/boot/dts/st/stm32mp13xf.dtsi | 1 + 4 files changed, 29 insertions(+)
diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi index 6ba8e3fd43b0..74ceece168ce 100644 --- a/arch/arm/boot/dts/st/stm32mp131.dtsi +++ b/arch/arm/boot/dts/st/stm32mp131.dtsi @@ -883,6 +883,7 @@ etzpc: bus@5c007000 { reg = <0x5c007000 0x400>; #address-cells = <1>; #size-cells = <1>; + #access-controller-cells = <1>; ranges;
adc_2: adc@48004000 { @@ -895,6 +896,7 @@ adc_2: adc@48004000 { #interrupt-cells = <1>; #address-cells = <1>; #size-cells = <0>; + access-controllers = <&etzpc 33>; status = "disabled";
adc2: adc@0 { @@ -942,6 +944,7 @@ usbotg_hs: usb@49000000 { dr_mode = "otg"; otg-rev = <0x200>; usb33d-supply = <&scmi_usb33>; + access-controllers = <&etzpc 34>; status = "disabled"; };
@@ -955,6 +958,7 @@ usart1: serial@4c000000 { dmas = <&dmamux1 41 0x400 0x5>, <&dmamux1 42 0x400 0x1>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 16>; status = "disabled"; };
@@ -968,6 +972,7 @@ usart2: serial@4c001000 { dmas = <&dmamux1 43 0x400 0x5>, <&dmamux1 44 0x400 0x1>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 17>; status = "disabled"; };
@@ -979,6 +984,7 @@ i2s4: audio-controller@4c002000 { dmas = <&dmamux1 83 0x400 0x01>, <&dmamux1 84 0x400 0x01>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 13>; status = "disabled"; };
@@ -993,6 +999,7 @@ spi4: spi@4c002000 { dmas = <&dmamux1 83 0x400 0x01>, <&dmamux1 84 0x400 0x01>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 18>; status = "disabled"; };
@@ -1007,6 +1014,7 @@ spi5: spi@4c003000 { dmas = <&dmamux1 85 0x400 0x01>, <&dmamux1 86 0x400 0x01>; dma-names = "rx", "tx"; + access-controllers = <&etzpc 19>; status = "disabled"; };
@@ -1025,6 +1033,7 @@ i2c3: i2c@4c004000 { dma-names = "rx", "tx"; st,syscfg-fmp = <&syscfg 0x4 0x4>; i2c-analog-filter; + access-controllers = <&etzpc 20>; status = "disabled"; };
@@ -1043,6 +1052,7 @@ i2c4: i2c@4c005000 { dma-names = "rx", "tx"; st,syscfg-fmp = <&syscfg 0x4 0x8>; i2c-analog-filter; + access-controllers = <&etzpc 21>; status = "disabled"; };
@@ -1061,6 +1071,7 @@ i2c5: i2c@4c006000 { dma-names = "rx", "tx"; st,syscfg-fmp = <&syscfg 0x4 0x10>; i2c-analog-filter; + access-controllers = <&etzpc 22>; status = "disabled"; };
@@ -1073,6 +1084,7 @@ timers12: timer@4c007000 { interrupt-names = "global"; clocks = <&rcc TIM12_K>; clock-names = "int"; + access-controllers = <&etzpc 23>; status = "disabled";
pwm { @@ -1097,6 +1109,7 @@ timers13: timer@4c008000 { interrupt-names = "global"; clocks = <&rcc TIM13_K>; clock-names = "int"; + access-controllers = <&etzpc 24>; status = "disabled";
pwm { @@ -1121,6 +1134,7 @@ timers14: timer@4c009000 { interrupt-names = "global"; clocks = <&rcc TIM14_K>; clock-names = "int"; + access-controllers = <&etzpc 25>; status = "disabled";
pwm { @@ -1150,6 +1164,7 @@ timers15: timer@4c00a000 { <&dmamux1 107 0x400 0x1>, <&dmamux1 108 0x400 0x1>; dma-names = "ch1", "up", "trig", "com"; + access-controllers = <&etzpc 26>; status = "disabled";
pwm { @@ -1177,6 +1192,7 @@ timers16: timer@4c00b000 { dmas = <&dmamux1 109 0x400 0x1>, <&dmamux1 110 0x400 0x1>; dma-names = "ch1", "up"; + access-controllers = <&etzpc 27>; status = "disabled";
pwm { @@ -1204,6 +1220,7 @@ timers17: timer@4c00c000 { dmas = <&dmamux1 111 0x400 0x1>, <&dmamux1 112 0x400 0x1>; dma-names = "ch1", "up"; + access-controllers = <&etzpc 28>; status = "disabled";
pwm { @@ -1228,6 +1245,7 @@ lptimer2: timer@50021000 { clocks = <&rcc LPTIM2_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 1>; status = "disabled";
pwm { @@ -1262,6 +1280,7 @@ lptimer3: timer@50022000 { clocks = <&rcc LPTIM3_K>; clock-names = "mux"; wakeup-source; + access-controllers = <&etzpc 2>; status = "disabled";
pwm { @@ -1290,6 +1309,7 @@ hash: hash@54003000 { resets = <&rcc HASH1_R>; dmas = <&mdma 30 0x2 0x1000a02 0x0 0x0>; dma-names = "in"; + access-controllers = <&etzpc 41>; };
rng: rng@54004000 { @@ -1297,6 +1317,7 @@ rng: rng@54004000 { reg = <0x54004000 0x400>; clocks = <&rcc RNG1_K>; resets = <&rcc RNG1_R>; + access-controllers = <&etzpc 40>; };
fmc: memory-controller@58002000 { @@ -1311,6 +1332,7 @@ fmc: memory-controller@58002000 { #size-cells = <1>; clocks = <&rcc FMC_K>; resets = <&rcc FMC_R>; + access-controllers = <&etzpc 54>; status = "disabled";
nand-controller@4,0 { @@ -1344,6 +1366,7 @@ qspi: spi@58003000 { dma-names = "tx", "rx"; clocks = <&rcc QSPI_K>; resets = <&rcc QSPI_R>; + access-controllers = <&etzpc 55>; status = "disabled"; };
@@ -1358,6 +1381,7 @@ sdmmc1: mmc@58005000 { cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <130000000>; + access-controllers = <&etzpc 50>; status = "disabled"; };
@@ -1372,6 +1396,7 @@ sdmmc2: mmc@58007000 { cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <130000000>; + access-controllers = <&etzpc 51>; status = "disabled"; };
@@ -1385,6 +1410,7 @@ usbphyc: usbphyc@5a006000 { resets = <&rcc USBPHY_R>; vdda1v1-supply = <&scmi_reg11>; vdda1v8-supply = <&scmi_reg18>; + access-controllers = <&etzpc 5>; status = "disabled";
usbphyc_port0: usb-phy@0 { diff --git a/arch/arm/boot/dts/st/stm32mp133.dtsi b/arch/arm/boot/dts/st/stm32mp133.dtsi index c4d3a520c14b..3e394c8e58b9 100644 --- a/arch/arm/boot/dts/st/stm32mp133.dtsi +++ b/arch/arm/boot/dts/st/stm32mp133.dtsi @@ -47,6 +47,7 @@ adc_1: adc@48003000 { #interrupt-cells = <1>; #address-cells = <1>; #size-cells = <0>; + access-controllers = <&etzpc 32>; status = "disabled";
adc1: adc@0 { diff --git a/arch/arm/boot/dts/st/stm32mp13xc.dtsi b/arch/arm/boot/dts/st/stm32mp13xc.dtsi index b9fb071a1471..a8bd5fe6536c 100644 --- a/arch/arm/boot/dts/st/stm32mp13xc.dtsi +++ b/arch/arm/boot/dts/st/stm32mp13xc.dtsi @@ -11,6 +11,7 @@ cryp: crypto@54002000 { interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; clocks = <&rcc CRYP1>; resets = <&rcc CRYP1_R>; + access-controllers = <&etzpc 42>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/st/stm32mp13xf.dtsi b/arch/arm/boot/dts/st/stm32mp13xf.dtsi index b9fb071a1471..a8bd5fe6536c 100644 --- a/arch/arm/boot/dts/st/stm32mp13xf.dtsi +++ b/arch/arm/boot/dts/st/stm32mp13xf.dtsi @@ -11,6 +11,7 @@ cryp: crypto@54002000 { interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; clocks = <&rcc CRYP1>; resets = <&rcc CRYP1_R>; + access-controllers = <&etzpc 42>; status = "disabled"; }; };
participants (3)
-
Gatien Chevallier
-
Rob Herring
-
Wolfram Sang