[PATCH 0/4] ASoC: codecs: wcd934x: add Headset and button detection support
This patchset adds support to MBHC(Multi Button Headset Control) block found in Qualcomm WCD codecs. MBHC support headset type detection, both Mechanical and electrical insert/removal detection along with 8 buttons detection, Over current interrupts on HPHL/R, Impedance Measurements on HPHL/R.
Eventhough MBHC block supports things like OverCurrent detection, Currently its reported as a kernel debug message. Should this be reported as an uevent to userspace? like the way USB reports? Any suggestions?
First patch adds a common mbhc driver and the second one wcd934x specific driver changes along with sdm845 soundcard related changes.
Common wcd-mbhc-v2 driver should be reusable across multiple codecs like WCD9335, WCD934x, WCD937x and WCD938x.
Most of the work is derived from downstream Qualcomm kernels. Credits to various Qualcomm authors from Patrick Lai's team who have contributed to this code.
This patchset
thanks, srini
Srinivas Kandagatla (4): ASoC: dt-bindings: wcd934x: add bindings for Headset Button detection ASoC: codecs: wcd: add multi button Headset detection support ASoC: codecs: wcd934x: add mbhc support ASoC: qcom: sdm845: add jack support for WCD934x
.../bindings/sound/qcom,wcd934x.yaml | 65 + include/linux/mfd/wcd934x/registers.h | 57 + sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/wcd-mbhc-v2.c | 1463 +++++++++++++++++ sound/soc/codecs/wcd-mbhc-v2.h | 340 ++++ sound/soc/codecs/wcd934x.c | 885 +++++++++- sound/soc/qcom/sdm845.c | 8 + 8 files changed, 2809 insertions(+), 15 deletions(-) create mode 100644 sound/soc/codecs/wcd-mbhc-v2.c create mode 100644 sound/soc/codecs/wcd-mbhc-v2.h
Add bindings required for Multi Button Headset detection. WCD934x support Headsets with upto 8 buttons including, impedance measurement on both L/R Headset speakers and cross connection detection.
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org --- .../bindings/sound/qcom,wcd934x.yaml | 65 +++++++++++++++++++ 1 file changed, 65 insertions(+)
diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml index e8f716b5f875..b25c6ca4e97c 100644 --- a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml +++ b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml @@ -77,6 +77,64 @@ properties: minimum: 1800000 maximum: 2850000
+ qcom,hphl-jack-type-normally-closed: + description: Indicates that HPHL jack switch type is normally closed + type: boolean + + qcom,ground-jack-type-normally-closed: + description: Indicates that Headset Ground switch type is normally closed + type: boolean + + qcom,mbhc-headset-vthreshold-microvolt: + description: Voltage threshold value for headset detection + minimum: 0 + maximum: 2850000 + + qcom,mbhc-headphone-vthreshold-microvolt: + description: Voltage threshold value for headphone detection + minimum: 0 + maximum: 2850000 + + qcom,mbhc-button0-vthreshold-microvolt: + description: Voltage threshold value for headset button0 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button1-vthreshold-microvolt: + description: Voltage threshold value for headset button1 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button2-vthreshold-microvolt: + description: Voltage threshold value for headset button2 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button3-vthreshold-microvolt: + description: Voltage threshold value for headset button3 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button4-vthreshold-microvolt: + description: Voltage threshold value for headset button4 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button5-vthreshold-microvolt: + description: Voltage threshold value for headset button5 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button6-vthreshold-microvolt: + description: Voltage threshold value for headset button6 + minimum: 0 + maximum: 500000 + + qcom,mbhc-button7-vthreshold-microvolt: + description: Voltage threshold value headset button7 + minimum: 0 + maximum: 500000 + clock-output-names: const: mclk
@@ -159,6 +217,13 @@ examples: qcom,micbias2-microvolt = <1800000>; qcom,micbias3-microvolt = <1800000>; qcom,micbias4-microvolt = <1800000>; + qcom,hphl-jack-type-normally-closed; + qcom,ground-jack-type-normally-closed; + qcom,mbhc-button0-vthreshold-microvolt = <75000>; + qcom,mbhc-button1-vthreshold-microvolt = <150000>; + qcom,mbhc-button2-vthreshold-microvolt = <237000>; + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; clock-names = "extclk"; clocks = <&rpmhcc 2>;
On Mon, May 10, 2021 at 11:11:58AM +0100, Srinivas Kandagatla wrote:
Add bindings required for Multi Button Headset detection. WCD934x support Headsets with upto 8 buttons including, impedance measurement on both L/R Headset speakers and cross connection detection.
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org
.../bindings/sound/qcom,wcd934x.yaml | 65 +++++++++++++++++++ 1 file changed, 65 insertions(+)
A search tells me this is not v1...
diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml index e8f716b5f875..b25c6ca4e97c 100644 --- a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml +++ b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml @@ -77,6 +77,64 @@ properties: minimum: 1800000 maximum: 2850000
- qcom,hphl-jack-type-normally-closed:
- description: Indicates that HPHL jack switch type is normally closed
- type: boolean
- qcom,ground-jack-type-normally-closed:
- description: Indicates that Headset Ground switch type is normally closed
- type: boolean
I asked before if 'normally closed' was the more common case and you said yes. So I'd expect 'open' here, but now you've changed the polarity of the property. And now not present is not described at all.
- qcom,mbhc-headset-vthreshold-microvolt:
- description: Voltage threshold value for headset detection
- minimum: 0
- maximum: 2850000
- qcom,mbhc-headphone-vthreshold-microvolt:
- description: Voltage threshold value for headphone detection
- minimum: 0
- maximum: 2850000
- qcom,mbhc-button0-vthreshold-microvolt:
- description: Voltage threshold value for headset button0
- minimum: 0
- maximum: 500000
- qcom,mbhc-button1-vthreshold-microvolt:
- description: Voltage threshold value for headset button1
- minimum: 0
- maximum: 500000
- qcom,mbhc-button2-vthreshold-microvolt:
- description: Voltage threshold value for headset button2
- minimum: 0
- maximum: 500000
- qcom,mbhc-button3-vthreshold-microvolt:
- description: Voltage threshold value for headset button3
- minimum: 0
- maximum: 500000
- qcom,mbhc-button4-vthreshold-microvolt:
- description: Voltage threshold value for headset button4
- minimum: 0
- maximum: 500000
- qcom,mbhc-button5-vthreshold-microvolt:
- description: Voltage threshold value for headset button5
- minimum: 0
- maximum: 500000
- qcom,mbhc-button6-vthreshold-microvolt:
- description: Voltage threshold value for headset button6
- minimum: 0
- maximum: 500000
- qcom,mbhc-button7-vthreshold-microvolt:
- description: Voltage threshold value headset button7
- minimum: 0
- maximum: 500000
These can all be a single pattern property: '^qcom,mbhc-button[0-7]-vthreshold-microvolt$'
Are there inter-dependencies between these properties? Are 0-7 meaningful or just an index? For the latter case, why not just make this an array?
- clock-output-names: const: mclk
@@ -159,6 +217,13 @@ examples: qcom,micbias2-microvolt = <1800000>; qcom,micbias3-microvolt = <1800000>; qcom,micbias4-microvolt = <1800000>;
qcom,hphl-jack-type-normally-closed;qcom,ground-jack-type-normally-closed;qcom,mbhc-button0-vthreshold-microvolt = <75000>;qcom,mbhc-button1-vthreshold-microvolt = <150000>;qcom,mbhc-button2-vthreshold-microvolt = <237000>;qcom,mbhc-headset-vthreshold-microvolt = <1700000>;qcom,mbhc-headphone-vthreshold-microvolt = <50000>; clock-names = "extclk"; clocks = <&rpmhcc 2>;-- 2.21.0
On 10/05/2021 17:45, Rob Herring wrote:
On Mon, May 10, 2021 at 11:11:58AM +0100, Srinivas Kandagatla wrote:
Add bindings required for Multi Button Headset detection. WCD934x support Headsets with upto 8 buttons including, impedance measurement on both L/R Headset speakers and cross connection detection.
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org
.../bindings/sound/qcom,wcd934x.yaml | 65 +++++++++++++++++++ 1 file changed, 65 insertions(+)
A search tells me this is not v1...
I did submit something for wcd9335 in the past but not for wcd934x which is still v1.
Most of these codecs have same MBHC block so the mbhc bindings look same across them.
diff --git a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml index e8f716b5f875..b25c6ca4e97c 100644 --- a/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml +++ b/Documentation/devicetree/bindings/sound/qcom,wcd934x.yaml @@ -77,6 +77,64 @@ properties: minimum: 1800000 maximum: 2850000
- qcom,hphl-jack-type-normally-closed:
- description: Indicates that HPHL jack switch type is normally closed
- type: boolean
- qcom,ground-jack-type-normally-closed:
- description: Indicates that Headset Ground switch type is normally closed
- type: boolean
I asked before if 'normally closed' was the more common case and you said yes. So I'd expect 'open' here, but now you've changed the polarity of the property. And now not present is not described at all.
Yes "normally closed" is the normal use case however Banajit commented on these binding with normally-open at https://lkml.org/lkml/2018/9/26/410
Ground pin may not be present on most of the headset jacks. So we can not consider the headset jacks as Normally closed when this property is not specified in the device tree.
So having binding with normally-closed makes it much safer to use.
- qcom,mbhc-headset-vthreshold-microvolt:
- description: Voltage threshold value for headset detection
- minimum: 0
- maximum: 2850000
- qcom,mbhc-headphone-vthreshold-microvolt:
- description: Voltage threshold value for headphone detection
- minimum: 0
- maximum: 2850000
- qcom,mbhc-button0-vthreshold-microvolt:
- description: Voltage threshold value for headset button0
- minimum: 0
- maximum: 500000
- qcom,mbhc-button1-vthreshold-microvolt:
- description: Voltage threshold value for headset button1
- minimum: 0
- maximum: 500000
- qcom,mbhc-button2-vthreshold-microvolt:
- description: Voltage threshold value for headset button2
- minimum: 0
- maximum: 500000
- qcom,mbhc-button3-vthreshold-microvolt:
- description: Voltage threshold value for headset button3
- minimum: 0
- maximum: 500000
- qcom,mbhc-button4-vthreshold-microvolt:
- description: Voltage threshold value for headset button4
- minimum: 0
- maximum: 500000
- qcom,mbhc-button5-vthreshold-microvolt:
- description: Voltage threshold value for headset button5
- minimum: 0
- maximum: 500000
- qcom,mbhc-button6-vthreshold-microvolt:
- description: Voltage threshold value for headset button6
- minimum: 0
- maximum: 500000
- qcom,mbhc-button7-vthreshold-microvolt:
- description: Voltage threshold value headset button7
- minimum: 0
- maximum: 500000
These can all be a single pattern property: '^qcom,mbhc-button[0-7]-vthreshold-microvolt$'
Thanks for the hint, this works, will change it in next version.
--srini
Most new Qualcomm WCD codecs support MBHC(Multi Button Headset Control) via ADC.
This patchset adds support to Common parts of this MBHC support so that WCD codecs need not duplicate them. To do that codec exposes set of register fields and callbacks to this common driver to control it.
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org --- sound/soc/codecs/Kconfig | 3 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/wcd-mbhc-v2.c | 1463 ++++++++++++++++++++++++++++++++ sound/soc/codecs/wcd-mbhc-v2.h | 340 ++++++++ 4 files changed, 1808 insertions(+) create mode 100644 sound/soc/codecs/wcd-mbhc-v2.c create mode 100644 sound/soc/codecs/wcd-mbhc-v2.h
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 2a7b3e363069..2faf0809d01f 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -1525,6 +1525,9 @@ config SND_SOC_WCD9335 Qualcomm Technologies, Inc. (QTI) multimedia solutions, including the MSM8996, MSM8976, and MSM8956 chipsets.
+config SND_SOC_WCD_MBHC + tristate + config SND_SOC_WCD934X tristate "WCD9340/WCD9341 Codec" depends on COMMON_CLK diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 0efdba609048..a24bd8247d77 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -250,6 +250,7 @@ snd-soc-twl6040-objs := twl6040.o snd-soc-uda1334-objs := uda1334.o snd-soc-uda134x-objs := uda134x.o snd-soc-uda1380-objs := uda1380.o +snd-soc-wcd-mbhc-objs := wcd-mbhc-v2.o snd-soc-wcd9335-objs := wcd-clsh-v2.o wcd9335.o snd-soc-wcd934x-objs := wcd-clsh-v2.o wcd934x.o snd-soc-wl1273-objs := wl1273.o @@ -572,6 +573,7 @@ obj-$(CONFIG_SND_SOC_TWL6040) += snd-soc-twl6040.o obj-$(CONFIG_SND_SOC_UDA1334) += snd-soc-uda1334.o obj-$(CONFIG_SND_SOC_UDA134X) += snd-soc-uda134x.o obj-$(CONFIG_SND_SOC_UDA1380) += snd-soc-uda1380.o +obj-$(CONFIG_SND_SOC_WCD_MBHC) += snd-soc-wcd-mbhc.o obj-$(CONFIG_SND_SOC_WCD9335) += snd-soc-wcd9335.o obj-$(CONFIG_SND_SOC_WCD934X) += snd-soc-wcd934x.o obj-$(CONFIG_SND_SOC_WL1273) += snd-soc-wl1273.o diff --git a/sound/soc/codecs/wcd-mbhc-v2.c b/sound/soc/codecs/wcd-mbhc-v2.c new file mode 100644 index 000000000000..7e1697956037 --- /dev/null +++ b/sound/soc/codecs/wcd-mbhc-v2.c @@ -0,0 +1,1463 @@ +// SPDX-License-Identifier: GPL-2.0-only +// Copyright (c) 2015-2021, The Linux Foundation. All rights reserved. + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/printk.h> +#include <linux/delay.h> +#include <linux/kernel.h> +#include <sound/soc.h> +#include <sound/jack.h> +#include "wcd-mbhc-v2.h" + +#define HS_DETECT_PLUG_TIME_MS (3 * 1000) +#define MBHC_BUTTON_PRESS_THRESHOLD_MIN 250 +#define GND_MIC_SWAP_THRESHOLD 4 +#define WCD_FAKE_REMOVAL_MIN_PERIOD_MS 100 +#define HPHL_CROSS_CONN_THRESHOLD 100 +#define HS_VREF_MIN_VAL 1400 +#define FAKE_REM_RETRY_ATTEMPTS 3 +#define WCD_MBHC_ADC_HS_THRESHOLD_MV 1700 +#define WCD_MBHC_ADC_HPH_THRESHOLD_MV 75 +#define WCD_MBHC_ADC_MICBIAS_MV 1800 +#define WCD_MBHC_FAKE_INS_RETRY 4 + +#define WCD_MBHC_JACK_MASK (SND_JACK_HEADSET | SND_JACK_LINEOUT | \ + SND_JACK_MECHANICAL) + +#define WCD_MBHC_JACK_BUTTON_MASK (SND_JACK_BTN_0 | SND_JACK_BTN_1 | \ + SND_JACK_BTN_2 | SND_JACK_BTN_3 | \ + SND_JACK_BTN_4 | SND_JACK_BTN_5) + +enum wcd_mbhc_adc_mux_ctl { + MUX_CTL_AUTO = 0, + MUX_CTL_IN2P, + MUX_CTL_IN3P, + MUX_CTL_IN4P, + MUX_CTL_HPH_L, + MUX_CTL_HPH_R, + MUX_CTL_NONE, +}; + +struct wcd_mbhc { + struct device *dev; + struct snd_soc_component *component; + struct snd_soc_jack *jack; + struct wcd_mbhc_config *cfg; + const struct wcd_mbhc_cb *mbhc_cb; + const struct wcd_mbhc_intr *intr_ids; + struct wcd_mbhc_field *fields; + /* Delayed work to report long button press */ + struct delayed_work mbhc_btn_dwork; + /* Work to correct accessory type */ + struct work_struct correct_plug_swch; + struct mutex lock; + int buttons_pressed; + u32 hph_status; /* track headhpone status */ + u8 current_plug; + bool is_btn_press; + bool in_swch_irq_handler; + bool hs_detect_work_stop; + bool is_hs_recording; + bool extn_cable_hph_rem; + bool force_linein; + bool impedance_detect; + unsigned long event_state; + unsigned long jiffies_atreport; + /* impedance of hphl and hphr */ + uint32_t zl, zr; + /* Holds type of Headset - Mono/Stereo */ + enum wcd_mbhc_hph_type hph_type; + /* Holds mbhc detection method - ADC/Legacy */ + int mbhc_detection_logic; +}; + +static inline int wcd_mbhc_write_field(const struct wcd_mbhc *mbhc, + int field, int val) +{ + if (!mbhc->fields[field].reg) + return 0; + + return snd_soc_component_write_field(mbhc->component, + mbhc->fields[field].reg, + mbhc->fields[field].mask, val); +} + +static inline int wcd_mbhc_read_field(const struct wcd_mbhc *mbhc, int field) +{ + if (!mbhc->fields[field].reg) + return 0; + + return snd_soc_component_read_field(mbhc->component, + mbhc->fields[field].reg, + mbhc->fields[field].mask); +} + +static void wcd_program_hs_vref(struct wcd_mbhc *mbhc) +{ + u32 reg_val = ((mbhc->cfg->v_hs_max - HS_VREF_MIN_VAL) / 100); + + wcd_mbhc_write_field(mbhc, WCD_MBHC_HS_VREF, reg_val); +} + +static void wcd_program_btn_threshold(const struct wcd_mbhc *mbhc, bool micbias) +{ + struct snd_soc_component *component = mbhc->component; + + mbhc->mbhc_cb->set_btn_thr(component, mbhc->cfg->btn_low, + mbhc->cfg->btn_high, + mbhc->cfg->num_btn, micbias); +} + +static void wcd_mbhc_curr_micbias_control(const struct wcd_mbhc *mbhc, + const enum wcd_mbhc_cs_mb_en_flag cs_mb_en) +{ + + /* + * Some codecs handle micbias/pullup enablement in codec + * drivers itself and micbias is not needed for regular + * plug type detection. So if micbias_control callback function + * is defined, just return. + */ + if (mbhc->mbhc_cb->mbhc_micbias_control) + return; + + switch (cs_mb_en) { + case WCD_MBHC_EN_CS: + wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); + /* Program Button threshold registers as per CS */ + wcd_program_btn_threshold(mbhc, false); + break; + case WCD_MBHC_EN_MB: + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + /* Disable PULL_UP_EN & enable MICBIAS */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 2); + /* Program Button threshold registers as per MICBIAS */ + wcd_program_btn_threshold(mbhc, true); + break; + case WCD_MBHC_EN_PULLUP: + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 1); + /* Program Button threshold registers as per MICBIAS */ + wcd_program_btn_threshold(mbhc, true); + break; + case WCD_MBHC_EN_NONE: + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 0); + break; + default: + dev_err(mbhc->dev, "%s: Invalid parameter", __func__); + break; + } +} + +int wcd_mbhc_event_notify(struct wcd_mbhc *mbhc, unsigned long event) +{ + + struct snd_soc_component *component; + bool micbias2 = false; + + if (!mbhc) + return 0; + + component = mbhc->component; + + if (mbhc->mbhc_cb->micbias_enable_status) + micbias2 = mbhc->mbhc_cb->micbias_enable_status(component, MIC_BIAS_2); + + switch (event) { + /* MICBIAS usage change */ + case WCD_EVENT_POST_DAPM_MICBIAS_2_ON: + mbhc->is_hs_recording = true; + break; + case WCD_EVENT_POST_MICBIAS_2_ON: + /* Disable current source if micbias2 enabled */ + if (mbhc->mbhc_cb->mbhc_micbias_control) { + if (wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN)) + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); + } else { + mbhc->is_hs_recording = true; + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); + } + break; + case WCD_EVENT_PRE_MICBIAS_2_OFF: + /* + * Before MICBIAS_2 is turned off, if FSM is enabled, + * make sure current source is enabled so as to detect + * button press/release events + */ + if (mbhc->mbhc_cb->mbhc_micbias_control/* && !mbhc->micbias_enable*/) { + if (wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN)) + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); + } + break; + /* MICBIAS usage change */ + case WCD_EVENT_POST_DAPM_MICBIAS_2_OFF: + mbhc->is_hs_recording = false; + break; + case WCD_EVENT_POST_MICBIAS_2_OFF: + if (!mbhc->mbhc_cb->mbhc_micbias_control) + mbhc->is_hs_recording = false; + + /* Enable PULL UP if PA's are enabled */ + if ((test_bit(WCD_MBHC_EVENT_PA_HPHL, &mbhc->event_state)) || + (test_bit(WCD_MBHC_EVENT_PA_HPHR, &mbhc->event_state))) + /* enable pullup and cs, disable mb */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_PULLUP); + else + /* enable current source and disable mb, pullup*/ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_CS); + + break; + case WCD_EVENT_POST_HPHL_PA_OFF: + clear_bit(WCD_MBHC_EVENT_PA_HPHL, &mbhc->event_state); + + /* check if micbias is enabled */ + if (micbias2) + /* Disable cs, pullup & enable micbias */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); + else + /* Disable micbias, pullup & enable cs */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_CS); + break; + case WCD_EVENT_POST_HPHR_PA_OFF: + clear_bit(WCD_MBHC_EVENT_PA_HPHR, &mbhc->event_state); + /* check if micbias is enabled */ + if (micbias2) + /* Disable cs, pullup & enable micbias */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); + else + /* Disable micbias, pullup & enable cs */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_CS); + break; + case WCD_EVENT_PRE_HPHL_PA_ON: + set_bit(WCD_MBHC_EVENT_PA_HPHL, &mbhc->event_state); + /* check if micbias is enabled */ + if (micbias2) + /* Disable cs, pullup & enable micbias */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); + else + /* Disable micbias, enable pullup & cs */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_PULLUP); + break; + case WCD_EVENT_PRE_HPHR_PA_ON: + set_bit(WCD_MBHC_EVENT_PA_HPHR, &mbhc->event_state); + /* check if micbias is enabled */ + if (micbias2) + /* Disable cs, pullup & enable micbias */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); + else + /* Disable micbias, enable pullup & cs */ + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_PULLUP); + break; + default: + break; + } + return 0; +} +EXPORT_SYMBOL(wcd_mbhc_event_notify); + +static int wcd_cancel_btn_work(struct wcd_mbhc *mbhc) +{ + return cancel_delayed_work_sync(&mbhc->mbhc_btn_dwork); +} + +static void wcd_micbias_disable(struct wcd_mbhc *mbhc) +{ + struct snd_soc_component *component = mbhc->component; + + if (mbhc->mbhc_cb->mbhc_micbias_control) + mbhc->mbhc_cb->mbhc_micbias_control(component, MIC_BIAS_2, MICB_DISABLE); + + if (mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic) + mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic(component, MIC_BIAS_2, false); + + if (mbhc->mbhc_cb->set_micbias_value) { + mbhc->mbhc_cb->set_micbias_value(component); + wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 0); + } +} + +static void wcd_mbhc_report_plug_removal(struct wcd_mbhc *mbhc, + enum snd_jack_types jack_type) +{ + mbhc->hph_status &= ~jack_type; + /* + * cancel possibly scheduled btn work and + * report release if we reported button press + */ + if (!wcd_cancel_btn_work(mbhc) && mbhc->buttons_pressed) { + snd_soc_jack_report(mbhc->jack, 0, mbhc->buttons_pressed); + mbhc->buttons_pressed &= ~WCD_MBHC_JACK_BUTTON_MASK; + } + + wcd_micbias_disable(mbhc); + mbhc->hph_type = WCD_MBHC_HPH_NONE; + mbhc->zl = mbhc->zr = 0; + snd_soc_jack_report(mbhc->jack, mbhc->hph_status, WCD_MBHC_JACK_MASK); + mbhc->current_plug = MBHC_PLUG_TYPE_NONE; + mbhc->force_linein = false; +} + +static void wcd_mbhc_compute_impedance(struct wcd_mbhc *mbhc) +{ + + if (!mbhc->impedance_detect) + return; + + if (mbhc->cfg->linein_th != 0) { + u8 fsm_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN); + /* Set MUX_CTL to AUTO for Z-det */ + + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, MUX_CTL_AUTO); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + mbhc->mbhc_cb->compute_impedance(mbhc->component, &mbhc->zl, &mbhc->zr); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, fsm_en); + } +} + +static void wcd_mbhc_report_plug_insertion(struct wcd_mbhc *mbhc, + enum snd_jack_types jack_type) +{ + bool is_pa_on; + /* + * Report removal of current jack type. + * Headphone to headset shouldn't report headphone + * removal. + */ + if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET && + jack_type == SND_JACK_HEADPHONE) + mbhc->hph_status &= ~SND_JACK_HEADSET; + + /* Report insertion */ + if (jack_type == SND_JACK_HEADPHONE) + mbhc->current_plug = MBHC_PLUG_TYPE_HEADPHONE; + else if (jack_type == SND_JACK_HEADSET) { + mbhc->current_plug = MBHC_PLUG_TYPE_HEADSET; + mbhc->jiffies_atreport = jiffies; + } else if (jack_type == SND_JACK_LINEOUT) + mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH; + + is_pa_on = wcd_mbhc_read_field(mbhc, WCD_MBHC_HPH_PA_EN); + + if (!is_pa_on) { + wcd_mbhc_compute_impedance(mbhc); + if ((mbhc->zl > mbhc->cfg->linein_th) && + (mbhc->zr > mbhc->cfg->linein_th) && + (jack_type == SND_JACK_HEADPHONE)) { + jack_type = SND_JACK_LINEOUT; + mbhc->force_linein = true; + mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH; + if (mbhc->hph_status) { + mbhc->hph_status &= ~(SND_JACK_HEADSET | + SND_JACK_LINEOUT); + snd_soc_jack_report(mbhc->jack, mbhc->hph_status, + WCD_MBHC_JACK_MASK); + } + } + } + + /* Do not calculate impedance again for lineout + * as during playback pa is on and impedance values + * will not be correct resulting in lineout detected + * as headphone. + */ + if (is_pa_on && mbhc->force_linein) { + jack_type = SND_JACK_LINEOUT; + mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH; + if (mbhc->hph_status) { + mbhc->hph_status &= ~(SND_JACK_HEADSET | + SND_JACK_LINEOUT); + snd_soc_jack_report(mbhc->jack, mbhc->hph_status, + WCD_MBHC_JACK_MASK); + } + } + + mbhc->hph_status |= jack_type; + + if (jack_type == SND_JACK_HEADPHONE && mbhc->mbhc_cb->mbhc_micb_ramp_control) + mbhc->mbhc_cb->mbhc_micb_ramp_control(mbhc->component, false); + + snd_soc_jack_report(mbhc->jack, (mbhc->hph_status | SND_JACK_MECHANICAL), + WCD_MBHC_JACK_MASK); +} + +static void wcd_mbhc_report_plug(struct wcd_mbhc *mbhc, int insertion, + enum snd_jack_types jack_type) +{ + + WARN_ON(!mutex_is_locked(&mbhc->lock)); + + if (!insertion) /* Report removal */ + wcd_mbhc_report_plug_removal(mbhc, jack_type); + else + wcd_mbhc_report_plug_insertion(mbhc, jack_type); + +} + +static void wcd_cancel_hs_detect_plug(struct wcd_mbhc *mbhc, + struct work_struct *work) +{ + mbhc->hs_detect_work_stop = true; + mutex_unlock(&mbhc->lock); + cancel_work_sync(work); + mutex_lock(&mbhc->lock); +} + +static void wcd_mbhc_cancel_pending_work(struct wcd_mbhc *mbhc) +{ + /* cancel pending button press */ + wcd_cancel_btn_work(mbhc); + /* cancel correct work function */ + wcd_cancel_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); +} + +static void wcd_mbhc_elec_hs_report_unplug(struct wcd_mbhc *mbhc) +{ + wcd_mbhc_cancel_pending_work(mbhc); + /* Report extension cable */ + wcd_mbhc_report_plug(mbhc, 1, SND_JACK_LINEOUT); + /* + * Disable HPHL trigger and MIC Schmitt triggers. + * Setup for insertion detection. + */ + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr); + wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_NONE); + /* Disable HW FSM */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 3); + + /* Set the detection type appropriately */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_DETECTION_TYPE, 1); + enable_irq(mbhc->intr_ids->mbhc_hs_ins_intr); +} + +static void wcd_mbhc_find_plug_and_report(struct wcd_mbhc *mbhc, + enum wcd_mbhc_plug_type plug_type) +{ + if (mbhc->current_plug == plug_type) + return; + + mutex_lock(&mbhc->lock); + + switch (plug_type) { + case MBHC_PLUG_TYPE_HEADPHONE: + wcd_mbhc_report_plug(mbhc, 1, SND_JACK_HEADPHONE); + break; + case MBHC_PLUG_TYPE_HEADSET: + wcd_mbhc_report_plug(mbhc, 1, SND_JACK_HEADSET); + break; + case MBHC_PLUG_TYPE_HIGH_HPH: + wcd_mbhc_report_plug(mbhc, 1, SND_JACK_LINEOUT); + break; + case MBHC_PLUG_TYPE_GND_MIC_SWAP: + if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) + wcd_mbhc_report_plug(mbhc, 0, SND_JACK_HEADPHONE); + if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET) + wcd_mbhc_report_plug(mbhc, 0, SND_JACK_HEADSET); + break; + default: + WARN(1, "Unexpected current plug_type %d, plug_type %d\n", + mbhc->current_plug, plug_type); + break; + } + mutex_unlock(&mbhc->lock); +} + +static void wcd_schedule_hs_detect_plug(struct wcd_mbhc *mbhc, + struct work_struct *work) +{ + WARN_ON(!mutex_is_locked(&mbhc->lock)); + mbhc->hs_detect_work_stop = false; + schedule_work(work); +} + +static void wcd_mbhc_adc_detect_plug_type(struct wcd_mbhc *mbhc) +{ + struct snd_soc_component *component = mbhc->component; + + WARN_ON(!mutex_is_locked(&mbhc->lock)); + + if (mbhc->mbhc_cb->hph_pull_down_ctrl) + mbhc->mbhc_cb->hph_pull_down_ctrl(component, false); + + wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 0); + + if (mbhc->mbhc_cb->mbhc_micbias_control) { + mbhc->mbhc_cb->mbhc_micbias_control(component, MIC_BIAS_2, + MICB_ENABLE); + wcd_schedule_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); + } +} + +static irqreturn_t wcd_mbhc_mech_plug_detect_irq(int irq, void *data) +{ + struct snd_soc_component *component; + enum snd_jack_types jack_type; + struct wcd_mbhc *mbhc = data; + bool detection_type; + + component = mbhc->component; + mutex_lock(&mbhc->lock); + + mbhc->in_swch_irq_handler = true; + + wcd_mbhc_cancel_pending_work(mbhc); + + detection_type = wcd_mbhc_read_field(mbhc, WCD_MBHC_MECH_DETECTION_TYPE); + + /* Set the detection type appropriately */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_MECH_DETECTION_TYPE, !detection_type); + + /* Enable micbias ramp */ + if (mbhc->mbhc_cb->mbhc_micb_ramp_control) + mbhc->mbhc_cb->mbhc_micb_ramp_control(component, true); + + if (detection_type) { + if (mbhc->current_plug != MBHC_PLUG_TYPE_NONE) + goto exit; + /* Make sure MASTER_BIAS_CTL is enabled */ + mbhc->mbhc_cb->mbhc_bias(component, true); + mbhc->is_btn_press = false; + wcd_mbhc_adc_detect_plug_type(mbhc); + } else { + /* Disable HW FSM */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); + mbhc->extn_cable_hph_rem = false; + + if (mbhc->current_plug == MBHC_PLUG_TYPE_NONE) + goto exit; + + mbhc->is_btn_press = false; + switch (mbhc->current_plug) { + case MBHC_PLUG_TYPE_HEADPHONE: + jack_type = SND_JACK_HEADPHONE; + break; + case MBHC_PLUG_TYPE_HEADSET: + jack_type = SND_JACK_HEADSET; + break; + case MBHC_PLUG_TYPE_HIGH_HPH: + if (mbhc->mbhc_detection_logic == WCD_DETECTION_ADC) + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_ISRC_EN, 0); + jack_type = SND_JACK_LINEOUT; + break; + case MBHC_PLUG_TYPE_GND_MIC_SWAP: + dev_err(mbhc->dev, "Ground and Mic Swapped on plug\n"); + break; + default: + dev_err(mbhc->dev, "Invalid current plug: %d\n", + mbhc->current_plug); + goto exit; + } + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr); + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_DETECTION_TYPE, 1); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 0); + wcd_mbhc_report_plug(mbhc, 0, jack_type); + } + +exit: + mbhc->in_swch_irq_handler = false; + mutex_unlock(&mbhc->lock); + return IRQ_HANDLED; +} + +static int wcd_mbhc_get_button_mask(struct wcd_mbhc *mbhc) +{ + int mask = 0; + int btn; + + btn = wcd_mbhc_read_field(mbhc, WCD_MBHC_BTN_RESULT); + + switch (btn) { + case 0: + mask = SND_JACK_BTN_0; + break; + case 1: + mask = SND_JACK_BTN_1; + break; + case 2: + mask = SND_JACK_BTN_2; + break; + case 3: + mask = SND_JACK_BTN_3; + break; + case 4: + mask = SND_JACK_BTN_4; + break; + case 5: + mask = SND_JACK_BTN_5; + break; + default: + break; + } + + return mask; +} + +static void wcd_btn_long_press_fn(struct work_struct *work) +{ + struct delayed_work *dwork = to_delayed_work(work); + struct wcd_mbhc *mbhc = container_of(dwork, struct wcd_mbhc, mbhc_btn_dwork); + + if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET) + snd_soc_jack_report(mbhc->jack, mbhc->buttons_pressed, + mbhc->buttons_pressed); +} + +static irqreturn_t wcd_mbhc_btn_press_handler(int irq, void *data) +{ + struct wcd_mbhc *mbhc = data; + int mask; + unsigned long msec_val; + + mutex_lock(&mbhc->lock); + wcd_cancel_btn_work(mbhc); + mbhc->is_btn_press = true; + msec_val = jiffies_to_msecs(jiffies - mbhc->jiffies_atreport); + + /* Too short, ignore button press */ + if (msec_val < MBHC_BUTTON_PRESS_THRESHOLD_MIN) + goto done; + + /* If switch interrupt already kicked in, ignore button press */ + if (mbhc->in_swch_irq_handler) + goto done; + + /* Plug isn't headset, ignore button press */ + if (mbhc->current_plug != MBHC_PLUG_TYPE_HEADSET) + goto done; + + mask = wcd_mbhc_get_button_mask(mbhc); + mbhc->buttons_pressed |= mask; + if (schedule_delayed_work(&mbhc->mbhc_btn_dwork, msecs_to_jiffies(400)) == 0) + WARN(1, "Button pressed twice without release event\n"); +done: + mutex_unlock(&mbhc->lock); + return IRQ_HANDLED; +} + +static irqreturn_t wcd_mbhc_btn_release_handler(int irq, void *data) +{ + struct wcd_mbhc *mbhc = data; + int ret; + + mutex_lock(&mbhc->lock); + if (mbhc->is_btn_press) + mbhc->is_btn_press = false; + else /* fake btn press */ + goto exit; + + if (!(mbhc->buttons_pressed & WCD_MBHC_JACK_BUTTON_MASK)) + goto exit; + + ret = wcd_cancel_btn_work(mbhc); + if (ret == 0) { /* Reporting long button release event */ + snd_soc_jack_report(mbhc->jack, 0, mbhc->buttons_pressed); + } else { + if (!mbhc->in_swch_irq_handler) { + /* Reporting btn press n Release */ + snd_soc_jack_report(mbhc->jack, mbhc->buttons_pressed, + mbhc->buttons_pressed); + snd_soc_jack_report(mbhc->jack, 0, mbhc->buttons_pressed); + } + } + mbhc->buttons_pressed &= ~WCD_MBHC_JACK_BUTTON_MASK; +exit: + mutex_unlock(&mbhc->lock); + + return IRQ_HANDLED; +} + +static irqreturn_t wcd_mbhc_hph_ocp_irq(struct wcd_mbhc *mbhc, bool hphr) +{ + + /* TODO Find a better way to report this to Userspace */ + dev_err(mbhc->dev, "MBHC Over Current on %s detected\n", + hphr ? "HPHR" : "HPHL"); + + wcd_mbhc_write_field(mbhc, WCD_MBHC_OCP_FSM_EN, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_OCP_FSM_EN, 1); + + return IRQ_HANDLED; +} + +static irqreturn_t wcd_mbhc_hphl_ocp_irq(int irq, void *data) +{ + return wcd_mbhc_hph_ocp_irq(data, false); +} + +static irqreturn_t wcd_mbhc_hphr_ocp_irq(int irq, void *data) +{ + return wcd_mbhc_hph_ocp_irq(data, true); +} + +static int wcd_mbhc_initialise(struct wcd_mbhc *mbhc) +{ + struct snd_soc_component *component = mbhc->component; + + mutex_lock(&mbhc->lock); + + /* enable HS detection */ + if (mbhc->mbhc_cb->hph_pull_up_control_v2) + mbhc->mbhc_cb->hph_pull_up_control_v2(component, + HS_PULLUP_I_DEFAULT); + else if (mbhc->mbhc_cb->hph_pull_up_control) + mbhc->mbhc_cb->hph_pull_up_control(component, I_DEFAULT); + else + wcd_mbhc_write_field(mbhc, WCD_MBHC_HS_L_DET_PULL_UP_CTRL, 3); + + wcd_mbhc_write_field(mbhc, WCD_MBHC_HPHL_PLUG_TYPE, mbhc->cfg->hphl_swh); + wcd_mbhc_write_field(mbhc, WCD_MBHC_GND_PLUG_TYPE, mbhc->cfg->gnd_swh); + wcd_mbhc_write_field(mbhc, WCD_MBHC_SW_HPH_LP_100K_TO_GND, 1); + if (mbhc->cfg->gnd_det_en && mbhc->mbhc_cb->mbhc_gnd_det_ctrl) + mbhc->mbhc_cb->mbhc_gnd_det_ctrl(component, true); + wcd_mbhc_write_field(mbhc, WCD_MBHC_HS_L_DET_PULL_UP_COMP_CTRL, 1); + + wcd_mbhc_write_field(mbhc, WCD_MBHC_L_DET_EN, 1); + + /* Insertion debounce set to 96ms */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_INSREM_DBNC, 6); + + /* Button Debounce set to 16ms */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_DBNC, 2); + + /* enable bias */ + mbhc->mbhc_cb->mbhc_bias(component, true); + /* enable MBHC clock */ + if (mbhc->mbhc_cb->clk_setup) + mbhc->mbhc_cb->clk_setup(component, true); + + /* program HS_VREF value */ + wcd_program_hs_vref(mbhc); + + wcd_program_btn_threshold(mbhc, false); + + mutex_unlock(&mbhc->lock); + + return 0; +} + +static int wcd_mbhc_get_micbias(struct wcd_mbhc *mbhc) +{ + int micbias = 0; + + if (mbhc->mbhc_cb->get_micbias_val) { + mbhc->mbhc_cb->get_micbias_val(mbhc->component, &micbias); + } else { + u8 vout_ctl = 0; + /* Read MBHC Micbias (Mic Bias2) voltage */ + vout_ctl = wcd_mbhc_read_field(mbhc, WCD_MBHC_MICB2_VOUT); + /* Formula for getting micbias from vout + * micbias = 1.0V + VOUT_CTL * 50mV + */ + micbias = 1000 + (vout_ctl * 50); + } + return micbias; +} + +static int wcd_get_voltage_from_adc(u8 val, int micbias) +{ + /* Formula for calculating voltage from ADC + * Voltage = ADC_RESULT*12.5mV*V_MICBIAS/1.8 + */ + return ((val * 125 * micbias)/(WCD_MBHC_ADC_MICBIAS_MV * 10)); +} + +static int wcd_measure_adc_continuous(struct wcd_mbhc *mbhc) +{ + u8 adc_result; + int output_mv; + int retry = 3; + u8 adc_en; + + /* Pre-requisites for ADC continuous measurement */ + /* Read legacy electircal detection and disable */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 0x00); + /* Set ADC to continuous measurement */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 1); + /* Read ADC Enable bit to restore after adc measurement */ + adc_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_EN); + /* Disable ADC_ENABLE bit */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); + /* Disable MBHC FSM */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); + /* Set the MUX selection to IN2P */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, MUX_CTL_IN2P); + /* Enable MBHC FSM */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + /* Enable ADC_ENABLE bit */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 1); + + while (retry--) { + /* wait for 3 msec before reading ADC result */ + usleep_range(3000, 3100); + adc_result = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_RESULT); + } + + /* Restore ADC Enable */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, adc_en); + /* Get voltage from ADC result */ + output_mv = wcd_get_voltage_from_adc(adc_result, wcd_mbhc_get_micbias(mbhc)); + + return output_mv; +} + +static int wcd_measure_adc_once(struct wcd_mbhc *mbhc, int mux_ctl) +{ + struct device *dev = mbhc->dev; + u8 adc_timeout = 0; + u8 adc_complete = 0; + u8 adc_result; + int retry = 6; + int ret; + int output_mv = 0; + u8 adc_en; + + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); + /* Read ADC Enable bit to restore after adc measurement */ + adc_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_EN); + /* Trigger ADC one time measurement */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); + /* Set the appropriate MUX selection */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, mux_ctl); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 1); + + while (retry--) { + /* wait for 600usec to get adc results */ + usleep_range(600, 610); + + /* check for ADC Timeout */ + adc_timeout = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_TIMEOUT); + if (adc_timeout) + continue; + + /* Read ADC complete bit */ + adc_complete = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_COMPLETE); + if (!adc_complete) + continue; + + /* Read ADC result */ + adc_result = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_RESULT); + + /* Get voltage from ADC result */ + output_mv = wcd_get_voltage_from_adc(adc_result, + wcd_mbhc_get_micbias(mbhc)); + break; + } + + /* Restore ADC Enable */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, adc_en); + + if (retry <= 0) { + dev_err(dev, "%s: adc complete: %d, adc timeout: %d\n", + __func__, adc_complete, adc_timeout); + ret = -EINVAL; + } else { + ret = output_mv; + } + + return ret; +} + +/* To determine if cross connection occurred */ +static int wcd_check_cross_conn(struct wcd_mbhc *mbhc) +{ + u8 adc_mode, elect_ctl, adc_en, fsm_en; + int hphl_adc_res, hphr_adc_res; + bool is_cross_conn = false; + + /* If PA is enabled, dont check for cross-connection */ + if (wcd_mbhc_read_field(mbhc, WCD_MBHC_HPH_PA_EN)) + return -EINVAL; + + /* Read legacy electircal detection and disable */ + elect_ctl = wcd_mbhc_read_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 0); + + /* Read and set ADC to single measurement */ + adc_mode = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_MODE); + /* Read ADC Enable bit to restore after adc measurement */ + adc_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_EN); + /* Read FSM status */ + fsm_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN); + + /* Get adc result for HPH L */ + hphl_adc_res = wcd_measure_adc_once(mbhc, MUX_CTL_HPH_L); + if (hphl_adc_res < 0) + return hphl_adc_res; + + /* Get adc result for HPH R in mV */ + hphr_adc_res = wcd_measure_adc_once(mbhc, MUX_CTL_HPH_R); + if (hphr_adc_res < 0) + return hphr_adc_res; + + if (hphl_adc_res > HPHL_CROSS_CONN_THRESHOLD || + hphr_adc_res > HPHL_CROSS_CONN_THRESHOLD) + is_cross_conn = true; + + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); + /* Set the MUX selection to Auto */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, MUX_CTL_AUTO); + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); + /* Restore ADC Enable */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, adc_en); + /* Restore ADC mode */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, adc_mode); + /* Restore FSM state */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, fsm_en); + /* Restore electrical detection */ + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, elect_ctl); + + return is_cross_conn; +} + +static int wcd_mbhc_adc_get_hs_thres(struct wcd_mbhc *mbhc) +{ + int hs_threshold, micbias_mv; + + micbias_mv = wcd_mbhc_get_micbias(mbhc); + if (mbhc->cfg->hs_thr) { + if (mbhc->cfg->micb_mv == micbias_mv) + hs_threshold = mbhc->cfg->hs_thr; + else + hs_threshold = (mbhc->cfg->hs_thr * + micbias_mv) / mbhc->cfg->micb_mv; + } else { + hs_threshold = ((WCD_MBHC_ADC_HS_THRESHOLD_MV * + micbias_mv) / WCD_MBHC_ADC_MICBIAS_MV); + } + return hs_threshold; +} + +static int wcd_mbhc_adc_get_hph_thres(struct wcd_mbhc *mbhc) +{ + int hph_threshold, micbias_mv; + + micbias_mv = wcd_mbhc_get_micbias(mbhc); + if (mbhc->cfg->hph_thr) { + if (mbhc->cfg->micb_mv == micbias_mv) + hph_threshold = mbhc->cfg->hph_thr; + else + hph_threshold = (mbhc->cfg->hph_thr * + micbias_mv) / mbhc->cfg->micb_mv; + } else { + hph_threshold = ((WCD_MBHC_ADC_HPH_THRESHOLD_MV * + micbias_mv) / WCD_MBHC_ADC_MICBIAS_MV); + } + return hph_threshold; +} + +static void wcd_mbhc_adc_update_fsm_source(struct wcd_mbhc *mbhc, + enum wcd_mbhc_plug_type plug_type) +{ + bool micbias2 = false; + + switch (plug_type) { + case MBHC_PLUG_TYPE_HEADPHONE: + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); + break; + case MBHC_PLUG_TYPE_HEADSET: + if (mbhc->mbhc_cb->micbias_enable_status) + micbias2 = mbhc->mbhc_cb->micbias_enable_status(mbhc->component, + MIC_BIAS_2); + + if (!mbhc->is_hs_recording && !micbias2) + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); + break; + default: + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); + break; + + }; +} + +static void wcd_mbhc_bcs_enable(struct wcd_mbhc *mbhc, int plug_type, bool enable) +{ + switch (plug_type) { + case MBHC_PLUG_TYPE_HEADSET: + case MBHC_PLUG_TYPE_HEADPHONE: + if (mbhc->mbhc_cb->bcs_enable) + mbhc->mbhc_cb->bcs_enable(mbhc->component, enable); + break; + default: + break; + } +} + +static int wcd_mbhc_get_plug_from_adc(struct wcd_mbhc *mbhc, int adc_result) + +{ + enum wcd_mbhc_plug_type plug_type; + u32 hph_thr, hs_thr; + + hs_thr = wcd_mbhc_adc_get_hs_thres(mbhc); + hph_thr = wcd_mbhc_adc_get_hph_thres(mbhc); + + if (adc_result < hph_thr) + plug_type = MBHC_PLUG_TYPE_HEADPHONE; + else if (adc_result > hs_thr) + plug_type = MBHC_PLUG_TYPE_HIGH_HPH; + else + plug_type = MBHC_PLUG_TYPE_HEADSET; + + return plug_type; +} + +static void wcd_correct_swch_plug(struct work_struct *work) +{ + struct wcd_mbhc *mbhc; + struct snd_soc_component *component; + enum wcd_mbhc_plug_type plug_type = MBHC_PLUG_TYPE_INVALID; + unsigned long timeout; + int pt_gnd_mic_swap_cnt = 0; + int output_mv, cross_conn, hs_threshold, try = 0; + bool is_pa_on; + + mbhc = container_of(work, struct wcd_mbhc, correct_plug_swch); + component = mbhc->component; + + hs_threshold = wcd_mbhc_adc_get_hs_thres(mbhc); + + /* Mask ADC COMPLETE interrupt */ + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); + + /* Check for cross connection */ + do { + cross_conn = wcd_check_cross_conn(mbhc); + try++; + } while (try < GND_MIC_SWAP_THRESHOLD); + + if (cross_conn > 0) { + plug_type = MBHC_PLUG_TYPE_GND_MIC_SWAP; + dev_err(mbhc->dev, "cross connection found, Plug type %d\n", + plug_type); + goto correct_plug_type; + } + + /* Find plug type */ + output_mv = wcd_measure_adc_continuous(mbhc); + plug_type = wcd_mbhc_get_plug_from_adc(mbhc, output_mv); + + /* + * Report plug type if it is either headset or headphone + * else start the 3 sec loop + */ + switch (plug_type) { + case MBHC_PLUG_TYPE_HEADPHONE: + wcd_mbhc_find_plug_and_report(mbhc, plug_type); + break; + case MBHC_PLUG_TYPE_HEADSET: + wcd_mbhc_find_plug_and_report(mbhc, plug_type); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 1); + break; + default: + break; + } + +correct_plug_type: + + /* Disable BCS slow insertion detection */ + wcd_mbhc_bcs_enable(mbhc, plug_type, false); + + timeout = jiffies + msecs_to_jiffies(HS_DETECT_PLUG_TIME_MS); + + while (!time_after(jiffies, timeout)) { + if (mbhc->hs_detect_work_stop) { + wcd_micbias_disable(mbhc); + goto exit; + } + + msleep(180); + /* + * Use ADC single mode to minimize the chance of missing out + * btn press/release for HEADSET type during correct work. + */ + output_mv = wcd_measure_adc_once(mbhc, MUX_CTL_IN2P); + plug_type = wcd_mbhc_get_plug_from_adc(mbhc, output_mv); + is_pa_on = wcd_mbhc_read_field(mbhc, WCD_MBHC_HPH_PA_EN); + + if ((output_mv <= hs_threshold) && !is_pa_on) { + /* Check for cross connection*/ + cross_conn = wcd_check_cross_conn(mbhc); + if (cross_conn > 0) { /* cross-connection */ + pt_gnd_mic_swap_cnt++; + if (pt_gnd_mic_swap_cnt < GND_MIC_SWAP_THRESHOLD) + continue; + else + plug_type = MBHC_PLUG_TYPE_GND_MIC_SWAP; + } else if (!cross_conn) { /* no cross connection */ + pt_gnd_mic_swap_cnt = 0; + plug_type = wcd_mbhc_get_plug_from_adc(mbhc, output_mv); + continue; + } else if (cross_conn < 0) /* Error */ + continue; + + if (pt_gnd_mic_swap_cnt == GND_MIC_SWAP_THRESHOLD) { + /* US_EU gpio present, flip switch */ + if (mbhc->cfg->swap_gnd_mic) { + if (mbhc->cfg->swap_gnd_mic(component, true)) + continue; + } + } + } + + if (output_mv > hs_threshold) /* cable is extension cable */ + plug_type = MBHC_PLUG_TYPE_HIGH_HPH; + } + + wcd_mbhc_bcs_enable(mbhc, plug_type, true); + + if (plug_type == MBHC_PLUG_TYPE_HIGH_HPH) + wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_ISRC_EN, 1); + + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); + wcd_mbhc_find_plug_and_report(mbhc, plug_type); + + /* + * Set DETECTION_DONE bit for HEADSET + * so that btn press/release interrupt can be generated. + * For other plug type, clear the bit. + */ + if (plug_type == MBHC_PLUG_TYPE_HEADSET) + wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 1); + else + wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 0); + + if (mbhc->mbhc_cb->mbhc_micbias_control) + wcd_mbhc_adc_update_fsm_source(mbhc, plug_type); + +exit: + if (mbhc->mbhc_cb->mbhc_micbias_control/* && !mbhc->micbias_enable*/) + mbhc->mbhc_cb->mbhc_micbias_control(component, MIC_BIAS_2, MICB_DISABLE); + + /* + * If plug type is corrected from special headset to headphone, + * clear the micbias enable flag, set micbias back to 1.8V and + * disable micbias. + */ + if (plug_type == MBHC_PLUG_TYPE_HEADPHONE) { + wcd_micbias_disable(mbhc); + /* + * Enable ADC COMPLETE interrupt for HEADPHONE. + * Btn release may happen after the correct work, ADC COMPLETE + * interrupt needs to be captured to correct plug type. + */ + enable_irq(mbhc->intr_ids->mbhc_hs_ins_intr); + } + + if (mbhc->mbhc_cb->hph_pull_down_ctrl) + mbhc->mbhc_cb->hph_pull_down_ctrl(component, true); +} + +static irqreturn_t wcd_mbhc_adc_hs_rem_irq(int irq, void *data) +{ + struct wcd_mbhc *mbhc = data; + unsigned long timeout; + int adc_threshold, output_mv, retry = 0; + bool hphpa_on = false; + + mutex_lock(&mbhc->lock); + timeout = jiffies + msecs_to_jiffies(WCD_FAKE_REMOVAL_MIN_PERIOD_MS); + adc_threshold = wcd_mbhc_adc_get_hs_thres(mbhc); + + do { + retry++; + /* + * read output_mv every 10ms to look for + * any change in IN2_P + */ + usleep_range(10000, 10100); + output_mv = wcd_measure_adc_once(mbhc, MUX_CTL_IN2P); + + /* Check for fake removal */ + if ((output_mv <= adc_threshold) && retry > FAKE_REM_RETRY_ATTEMPTS) + goto exit; + } while (!time_after(jiffies, timeout)); + + /* + * ADC COMPLETE and ELEC_REM interrupts are both enabled for + * HEADPHONE, need to reject the ADC COMPLETE interrupt which + * follows ELEC_REM one when HEADPHONE is removed. + */ + if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) + mbhc->extn_cable_hph_rem = true; + + wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); + wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); + wcd_mbhc_elec_hs_report_unplug(mbhc); + wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); + + if (hphpa_on) { + hphpa_on = false; + wcd_mbhc_write_field(mbhc, WCD_MBHC_HPH_PA_EN, 3); + } +exit: + mutex_unlock(&mbhc->lock); + return IRQ_HANDLED; +} + +static irqreturn_t wcd_mbhc_adc_hs_ins_irq(int irq, void *data) +{ + struct wcd_mbhc *mbhc = data; + u8 clamp_state = 0; + u8 clamp_retry = WCD_MBHC_FAKE_INS_RETRY; + + /* + * ADC COMPLETE and ELEC_REM interrupts are both enabled for HEADPHONE, + * need to reject the ADC COMPLETE interrupt which follows ELEC_REM one + * when HEADPHONE is removed. + */ + if (mbhc->extn_cable_hph_rem == true) { + mbhc->extn_cable_hph_rem = false; + return IRQ_HANDLED; + } + + do { + clamp_state = wcd_mbhc_read_field(mbhc, WCD_MBHC_IN2P_CLAMP_STATE); + if (clamp_state) + return IRQ_HANDLED; + /* + * check clamp for 120ms but at 30ms chunks to leave + * room for other interrupts to be processed + */ + usleep_range(30000, 30100); + } while (--clamp_retry); + + /* + * If current plug is headphone then there is no chance to + * get ADC complete interrupt, so connected cable should be + * headset not headphone. + */ + if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) { + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); + wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 1); + wcd_mbhc_find_plug_and_report(mbhc, MBHC_PLUG_TYPE_HEADSET); + return IRQ_HANDLED; + } + + return IRQ_HANDLED; +} + +int wcd_mbhc_get_impedance(struct wcd_mbhc *mbhc, uint32_t *zl, uint32_t *zr) +{ + *zl = mbhc->zl; + *zr = mbhc->zr; + + if (*zl && *zr) + return 0; + else + return -EINVAL; +} +EXPORT_SYMBOL(wcd_mbhc_get_impedance); + +void wcd_mbhc_set_hph_type(struct wcd_mbhc *mbhc, int hph_type) +{ + mbhc->hph_type = hph_type; +} +EXPORT_SYMBOL(wcd_mbhc_set_hph_type); + +int wcd_mbhc_get_hph_type(struct wcd_mbhc *mbhc) +{ + return mbhc->hph_type; +} +EXPORT_SYMBOL(wcd_mbhc_get_hph_type); + +int wcd_mbhc_start(struct wcd_mbhc *mbhc, struct wcd_mbhc_config *cfg, + struct snd_soc_jack *jack) +{ + if (!mbhc || !cfg || !jack) + return -EINVAL; + + mbhc->cfg = cfg; + mbhc->jack = jack; + + return wcd_mbhc_initialise(mbhc); +} +EXPORT_SYMBOL(wcd_mbhc_start); + +void wcd_mbhc_stop(struct wcd_mbhc *mbhc) +{ + mbhc->current_plug = MBHC_PLUG_TYPE_NONE; + mbhc->hph_status = 0; + disable_irq_nosync(mbhc->intr_ids->hph_left_ocp); + disable_irq_nosync(mbhc->intr_ids->hph_right_ocp); +} +EXPORT_SYMBOL(wcd_mbhc_stop); + +int wcd_dt_parse_mbhc_data(struct device *dev, struct wcd_mbhc_config *cfg) +{ + struct device_node *np = dev->of_node; + int ret, i, microvolt; + char prop_str[64]; + + if (of_property_read_bool(np, "qcom,hphl-jack-type-normally-closed")) + cfg->hphl_swh = true; + else + cfg->hphl_swh = false; + + if (of_property_read_bool(np, "qcom,ground-jack-type-normally-closed")) + cfg->gnd_swh = true; + else + cfg->gnd_swh = false; + + ret = of_property_read_u32(np, "qcom,mbhc-headset-vthreshold-microvolt", + µvolt); + if (ret) + dev_dbg(dev, "missing qcom,mbhc-hs-mic-max-vthreshold--microvolt in dt node\n"); + else + cfg->hs_thr = microvolt/1000; + + ret = of_property_read_u32(np, "qcom,mbhc-headphone-vthreshold-microvolt", + µvolt); + if (ret) + dev_dbg(dev, "missing qcom,mbhc-hs-mic-min-vthreshold-microvolt entry\n"); + else + cfg->hph_thr = microvolt/1000; + + for (i = 0; i < WCD_MBHC_DEF_BUTTONS; i++) { + sprintf(prop_str, "qcom,mbhc-button%d-vthreshold-microvolt", i); + ret = of_property_read_u32(np, prop_str, µvolt); + if (ret) /* default voltage */ + microvolt = 500000; + + /* Micro to Milli Volts */ + cfg->btn_high[i] = microvolt/1000; + } + + return 0; +} +EXPORT_SYMBOL(wcd_dt_parse_mbhc_data); + +struct wcd_mbhc *wcd_mbhc_init(struct snd_soc_component *component, + const struct wcd_mbhc_cb *mbhc_cb, + const struct wcd_mbhc_intr *intr_ids, + struct wcd_mbhc_field *fields, + bool impedance_det_en) +{ + struct device *dev = component->dev; + struct wcd_mbhc *mbhc; + int ret; + + if (!intr_ids || !fields || !mbhc_cb || !mbhc_cb->mbhc_bias || !mbhc_cb->set_btn_thr) { + dev_err(dev, "%s: Insufficient mbhc configuration\n", __func__); + return ERR_PTR(-EINVAL); + } + + mbhc = devm_kzalloc(dev, sizeof(*mbhc), GFP_KERNEL); + if (!mbhc) + return ERR_PTR(-ENOMEM); + + mbhc->component = component; + mbhc->dev = dev; + mbhc->intr_ids = intr_ids; + mbhc->mbhc_cb = mbhc_cb; + mbhc->fields = fields; + mbhc->mbhc_detection_logic = WCD_DETECTION_ADC; + + if (mbhc_cb->compute_impedance) + mbhc->impedance_detect = impedance_det_en; + + INIT_DELAYED_WORK(&mbhc->mbhc_btn_dwork, wcd_btn_long_press_fn); + + mutex_init(&mbhc->lock); + + INIT_WORK(&mbhc->correct_plug_swch, wcd_correct_swch_plug); + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_sw_intr, NULL, + wcd_mbhc_mech_plug_detect_irq, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "mbhc sw intr", mbhc); + if (ret) + goto err; + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_btn_press_intr, NULL, + wcd_mbhc_btn_press_handler, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "Button Press detect", mbhc); + if (ret) + goto err; + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_btn_release_intr, NULL, + wcd_mbhc_btn_release_handler, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "Button Release detect", mbhc); + if (ret) + goto err; + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_hs_ins_intr, NULL, + wcd_mbhc_adc_hs_ins_irq, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "Elect Insert", mbhc); + if (ret) + goto err; + + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->mbhc_hs_rem_intr, NULL, + wcd_mbhc_adc_hs_rem_irq, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "Elect Remove", mbhc); + if (ret) + goto err; + + disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr); + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->hph_left_ocp, NULL, + wcd_mbhc_hphl_ocp_irq, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "HPH_L OCP detect", mbhc); + if (ret) + goto err; + + ret = devm_request_threaded_irq(dev, mbhc->intr_ids->hph_right_ocp, NULL, + wcd_mbhc_hphr_ocp_irq, + IRQF_ONESHOT | IRQF_TRIGGER_RISING, + "HPH_R OCP detect", mbhc); + if (ret) + goto err; + + return mbhc; +err: + dev_err(dev, "Failed to request mbhc interrupts %d\n", ret); + + return ERR_PTR(ret); +} +EXPORT_SYMBOL(wcd_mbhc_init); + +void wcd_mbhc_deinit(struct wcd_mbhc *mbhc) +{ + mutex_lock(&mbhc->lock); + wcd_cancel_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); + mutex_unlock(&mbhc->lock); +} +EXPORT_SYMBOL(wcd_mbhc_deinit); + +static int __init mbhc_init(void) +{ + return 0; +} + +static void __exit mbhc_exit(void) +{ +} + +module_init(mbhc_init); +module_exit(mbhc_exit); + +MODULE_DESCRIPTION("wcd MBHC v2 module"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/wcd-mbhc-v2.h b/sound/soc/codecs/wcd-mbhc-v2.h new file mode 100644 index 000000000000..006118f3e81f --- /dev/null +++ b/sound/soc/codecs/wcd-mbhc-v2.h @@ -0,0 +1,340 @@ +/* SPDX-License-Identifier: GPL-2.0 */ + +#ifndef __WCD_MBHC_V2_H__ +#define __WCD_MBHC_V2_H__ + +#include <sound/jack.h> + +#define WCD_MBHC_FIELD(id, rreg, rmask) \ + [id] = { .reg = rreg, .mask = rmask } + +enum wcd_mbhc_field_function { + WCD_MBHC_L_DET_EN, + WCD_MBHC_GND_DET_EN, + WCD_MBHC_MECH_DETECTION_TYPE, + WCD_MBHC_MIC_CLAMP_CTL, + WCD_MBHC_ELECT_DETECTION_TYPE, + WCD_MBHC_HS_L_DET_PULL_UP_CTRL, + WCD_MBHC_HS_L_DET_PULL_UP_COMP_CTRL, + WCD_MBHC_HPHL_PLUG_TYPE, + WCD_MBHC_GND_PLUG_TYPE, + WCD_MBHC_SW_HPH_LP_100K_TO_GND, + WCD_MBHC_ELECT_SCHMT_ISRC, + WCD_MBHC_FSM_EN, + WCD_MBHC_INSREM_DBNC, + WCD_MBHC_BTN_DBNC, + WCD_MBHC_HS_VREF, + WCD_MBHC_HS_COMP_RESULT, + WCD_MBHC_IN2P_CLAMP_STATE, + WCD_MBHC_MIC_SCHMT_RESULT, + WCD_MBHC_HPHL_SCHMT_RESULT, + WCD_MBHC_HPHR_SCHMT_RESULT, + WCD_MBHC_OCP_FSM_EN, + WCD_MBHC_BTN_RESULT, + WCD_MBHC_BTN_ISRC_CTL, + WCD_MBHC_ELECT_RESULT, + WCD_MBHC_MICB_CTRL, /* Pull-up and micb control */ + WCD_MBHC_HPH_CNP_WG_TIME, + WCD_MBHC_HPHR_PA_EN, + WCD_MBHC_HPHL_PA_EN, + WCD_MBHC_HPH_PA_EN, + WCD_MBHC_SWCH_LEVEL_REMOVE, + WCD_MBHC_PULLDOWN_CTRL, + WCD_MBHC_ANC_DET_EN, + WCD_MBHC_FSM_STATUS, + WCD_MBHC_MUX_CTL, + WCD_MBHC_MOISTURE_STATUS, + WCD_MBHC_HPHR_GND, + WCD_MBHC_HPHL_GND, + WCD_MBHC_HPHL_OCP_DET_EN, + WCD_MBHC_HPHR_OCP_DET_EN, + WCD_MBHC_HPHL_OCP_STATUS, + WCD_MBHC_HPHR_OCP_STATUS, + WCD_MBHC_ADC_EN, + WCD_MBHC_ADC_COMPLETE, + WCD_MBHC_ADC_TIMEOUT, + WCD_MBHC_ADC_RESULT, + WCD_MBHC_MICB2_VOUT, + WCD_MBHC_ADC_MODE, + WCD_MBHC_DETECTION_DONE, + WCD_MBHC_ELECT_ISRC_EN, + WCD_MBHC_REG_FUNC_MAX, +}; + +#define WCD_MBHC_DEF_BUTTONS 8 +#define WCD_MBHC_KEYCODE_NUM 8 +#define WCD_MBHC_USLEEP_RANGE_MARGIN_US 100 +#define WCD_MBHC_THR_HS_MICB_MV 2700 +#define WCD_MONO_HS_MIN_THR 2 + +enum wcd_mbhc_detect_logic { + WCD_DETECTION_LEGACY, + WCD_DETECTION_ADC, +}; + +enum wcd_mbhc_cs_mb_en_flag { + WCD_MBHC_EN_CS = 0, + WCD_MBHC_EN_MB, + WCD_MBHC_EN_PULLUP, + WCD_MBHC_EN_NONE, +}; + +enum { + WCD_MBHC_ELEC_HS_INS, + WCD_MBHC_ELEC_HS_REM, +}; + +enum wcd_mbhc_plug_type { + MBHC_PLUG_TYPE_INVALID = -1, + MBHC_PLUG_TYPE_NONE, + MBHC_PLUG_TYPE_HEADSET, + MBHC_PLUG_TYPE_HEADPHONE, + MBHC_PLUG_TYPE_HIGH_HPH, + MBHC_PLUG_TYPE_GND_MIC_SWAP, +}; + +enum pa_dac_ack_flags { + WCD_MBHC_HPHL_PA_OFF_ACK = 0, + WCD_MBHC_HPHR_PA_OFF_ACK, +}; + +enum wcd_mbhc_btn_det_mem { + WCD_MBHC_BTN_DET_V_BTN_LOW, + WCD_MBHC_BTN_DET_V_BTN_HIGH +}; + +enum { + MIC_BIAS_1 = 1, + MIC_BIAS_2, + MIC_BIAS_3, + MIC_BIAS_4 +}; + +enum { + MICB_PULLUP_ENABLE, + MICB_PULLUP_DISABLE, + MICB_ENABLE, + MICB_DISABLE, +}; + +enum wcd_notify_event { + WCD_EVENT_INVALID, + /* events for micbias ON and OFF */ + WCD_EVENT_PRE_MICBIAS_2_OFF, + WCD_EVENT_POST_MICBIAS_2_OFF, + WCD_EVENT_PRE_MICBIAS_2_ON, + WCD_EVENT_POST_MICBIAS_2_ON, + WCD_EVENT_PRE_DAPM_MICBIAS_2_OFF, + WCD_EVENT_POST_DAPM_MICBIAS_2_OFF, + WCD_EVENT_PRE_DAPM_MICBIAS_2_ON, + WCD_EVENT_POST_DAPM_MICBIAS_2_ON, + /* events for PA ON and OFF */ + WCD_EVENT_PRE_HPHL_PA_ON, + WCD_EVENT_POST_HPHL_PA_OFF, + WCD_EVENT_PRE_HPHR_PA_ON, + WCD_EVENT_POST_HPHR_PA_OFF, + WCD_EVENT_PRE_HPHL_PA_OFF, + WCD_EVENT_PRE_HPHR_PA_OFF, + WCD_EVENT_OCP_OFF, + WCD_EVENT_OCP_ON, + WCD_EVENT_LAST, +}; + +enum wcd_mbhc_event_state { + WCD_MBHC_EVENT_PA_HPHL, + WCD_MBHC_EVENT_PA_HPHR, +}; + +enum wcd_mbhc_hph_type { + WCD_MBHC_HPH_NONE = 0, + WCD_MBHC_HPH_MONO, + WCD_MBHC_HPH_STEREO, +}; + +/* + * These enum definitions are directly mapped to the register + * definitions + */ + +enum mbhc_hs_pullup_iref { + I_DEFAULT = -1, + I_OFF = 0, + I_1P0_UA, + I_2P0_UA, + I_3P0_UA, +}; + +enum mbhc_hs_pullup_iref_v2 { + HS_PULLUP_I_DEFAULT = -1, + HS_PULLUP_I_3P0_UA = 0, + HS_PULLUP_I_2P25_UA, + HS_PULLUP_I_1P5_UA, + HS_PULLUP_I_0P75_UA, + HS_PULLUP_I_1P125_UA = 0x05, + HS_PULLUP_I_0P375_UA = 0x07, + HS_PULLUP_I_2P0_UA, + HS_PULLUP_I_1P0_UA = 0x0A, + HS_PULLUP_I_0P5_UA, + HS_PULLUP_I_0P25_UA = 0x0F, + HS_PULLUP_I_0P125_UA = 0x17, + HS_PULLUP_I_OFF, +}; + +enum mbhc_moisture_rref { + R_OFF, + R_24_KOHM, + R_84_KOHM, + R_184_KOHM, +}; + +struct wcd_mbhc_config { + int btn_high[WCD_MBHC_DEF_BUTTONS]; + int btn_low[WCD_MBHC_DEF_BUTTONS]; + int v_hs_max; + int num_btn; + bool mono_stero_detection; + bool (*swap_gnd_mic)(struct snd_soc_component *component, bool active); + bool hs_ext_micbias; + bool gnd_det_en; + uint32_t linein_th; + bool moisture_en; + int mbhc_micbias; + int anc_micbias; + bool moisture_duty_cycle_en; + bool hphl_swh; /*track HPHL switch NC / NO */ + bool gnd_swh; /*track GND switch NC / NO */ + u32 hs_thr; + u32 hph_thr; + u32 micb_mv; + u32 moist_vref; + u32 moist_iref; + u32 moist_rref; +}; + +struct wcd_mbhc_intr { + int mbhc_sw_intr; + int mbhc_btn_press_intr; + int mbhc_btn_release_intr; + int mbhc_hs_ins_intr; + int mbhc_hs_rem_intr; + int hph_left_ocp; + int hph_right_ocp; +}; + +struct wcd_mbhc_field { + u16 reg; + u8 mask; +}; + +struct wcd_mbhc; + +struct wcd_mbhc_cb { + void (*update_cross_conn_thr)(struct snd_soc_component *component); + void (*get_micbias_val)(struct snd_soc_component *component, int *mb); + void (*bcs_enable)(struct snd_soc_component *component, bool bcs_enable); + void (*compute_impedance)(struct snd_soc_component *component, + uint32_t *zl, uint32_t *zr); + void (*set_micbias_value)(struct snd_soc_component *component); + void (*set_auto_zeroing)(struct snd_soc_component *component, + bool enable); + void (*clk_setup)(struct snd_soc_component *component, bool enable); + bool (*micbias_enable_status)(struct snd_soc_component *component, int micb_num); + void (*mbhc_bias)(struct snd_soc_component *component, bool enable); + void (*set_btn_thr)(struct snd_soc_component *component, + int *btn_low, int *btn_high, + int num_btn, bool is_micbias); + void (*hph_pull_up_control)(struct snd_soc_component *component, + enum mbhc_hs_pullup_iref); + int (*mbhc_micbias_control)(struct snd_soc_component *component, + int micb_num, int req); + void (*mbhc_micb_ramp_control)(struct snd_soc_component *component, + bool enable); + bool (*extn_use_mb)(struct snd_soc_component *component); + int (*mbhc_micb_ctrl_thr_mic)(struct snd_soc_component *component, + int micb_num, bool req_en); + void (*mbhc_gnd_det_ctrl)(struct snd_soc_component *component, + bool enable); + void (*hph_pull_down_ctrl)(struct snd_soc_component *component, + bool enable); + void (*mbhc_moisture_config)(struct snd_soc_component *component); + void (*update_anc_state)(struct snd_soc_component *component, + bool enable, int anc_num); + void (*hph_pull_up_control_v2)(struct snd_soc_component *component, + int pull_up_cur); + bool (*mbhc_get_moisture_status)(struct snd_soc_component *component); + void (*mbhc_moisture_polling_ctrl)(struct snd_soc_component *component, bool enable); + void (*mbhc_moisture_detect_en)(struct snd_soc_component *component, bool enable); +}; + +#if IS_ENABLED(CONFIG_SND_SOC_WCD_MBHC) +int wcd_dt_parse_mbhc_data(struct device *dev, struct wcd_mbhc_config *cfg); +int wcd_mbhc_start(struct wcd_mbhc *mbhc, struct wcd_mbhc_config *mbhc_cfg, + struct snd_soc_jack *jack); +void wcd_mbhc_stop(struct wcd_mbhc *mbhc); +void wcd_mbhc_set_hph_type(struct wcd_mbhc *mbhc, int hph_type); +int wcd_mbhc_get_hph_type(struct wcd_mbhc *mbhc); +struct wcd_mbhc *wcd_mbhc_init(struct snd_soc_component *component, + const struct wcd_mbhc_cb *mbhc_cb, + const struct wcd_mbhc_intr *mbhc_cdc_intr_ids, + struct wcd_mbhc_field *fields, + bool impedance_det_en); +int wcd_mbhc_get_impedance(struct wcd_mbhc *mbhc, uint32_t *zl, + uint32_t *zr); +void wcd_mbhc_deinit(struct wcd_mbhc *mbhc); +int wcd_mbhc_event_notify(struct wcd_mbhc *mbhc, unsigned long event); + +#else +static inline int wcd_dt_parse_mbhc_data(struct device *dev, + struct wcd_mbhc_config *cfg) +{ + return -ENOTSUPP; +} + +static inline void wcd_mbhc_stop(struct wcd_mbhc *mbhc) +{ +} + +static inline struct wcd_mbhc *wcd_mbhc_init(struct snd_soc_component *component, + const struct wcd_mbhc_cb *mbhc_cb, + const struct wcd_mbhc_intr *mbhc_cdc_intr_ids, + struct wcd_mbhc_field *fields, + bool impedance_det_en) +{ + return ERR_PTR(-ENOTSUPP); +} + +static inline void wcd_mbhc_set_hph_type(struct wcd_mbhc *mbhc, int hph_type) +{ +} + +static inline int wcd_mbhc_get_hph_type(struct wcd_mbhc *mbhc) +{ + return -ENOTSUPP; +} + +static inline int wcd_mbhc_event_notify(struct wcd_mbhc *mbhc, unsigned long event) +{ + return -ENOTSUPP; +} + +static inline int wcd_mbhc_start(struct wcd_mbhc *mbhc, + struct wcd_mbhc_config *mbhc_cfg, + struct snd_soc_jack *jack) +{ + return 0; +} + +static inline int wcd_mbhc_get_impedance(struct wcd_mbhc *mbhc, + uint32_t *zl, + uint32_t *zr) +{ + *zl = 0; + *zr = 0; + return -EINVAL; +} +static inline void wcd_mbhc_deinit(struct wcd_mbhc *mbhc) +{ +} +#endif + +#endif /* __WCD_MBHC_V2_H__ */
WCD934x has Multi Button Headset Control hardware to support Headset insertion, type detection, 8 headset buttons detection, Over Current detection and Impedence measurements.
This patch adds support for this feature via common mbhc layer.
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org --- include/linux/mfd/wcd934x/registers.h | 57 ++ sound/soc/codecs/Kconfig | 1 + sound/soc/codecs/wcd934x.c | 885 +++++++++++++++++++++++++- 3 files changed, 928 insertions(+), 15 deletions(-)
diff --git a/include/linux/mfd/wcd934x/registers.h b/include/linux/mfd/wcd934x/registers.h index bb8d2e276668..76a943c83c63 100644 --- a/include/linux/mfd/wcd934x/registers.h +++ b/include/linux/mfd/wcd934x/registers.h @@ -18,6 +18,8 @@ #define WCD934X_EFUSE_SENSE_STATE_DEF 0x10 #define WCD934X_EFUSE_SENSE_EN_MASK BIT(0) #define WCD934X_EFUSE_SENSE_ENABLE BIT(0) +#define WCD934X_CHIP_TIER_CTRL_EFUSE_VAL_OUT1 0x002a +#define WCD934X_CHIP_TIER_CTRL_EFUSE_VAL_OUT2 0x002b #define WCD934X_CHIP_TIER_CTRL_EFUSE_VAL_OUT14 0x0037 #define WCD934X_CHIP_TIER_CTRL_EFUSE_VAL_OUT15 0x0038 #define WCD934X_CHIP_TIER_CTRL_EFUSE_STATUS 0x0039 @@ -103,21 +105,58 @@ #define WCD934X_ANA_AMIC3 0x0610 #define WCD934X_ANA_AMIC4 0x0611 #define WCD934X_ANA_MBHC_MECH 0x0614 +#define WCD934X_MBHC_L_DET_EN_MASK BIT(7) +#define WCD934X_MBHC_L_DET_EN BIT(7) +#define WCD934X_MBHC_GND_DET_EN_MASK BIT(6) +#define WCD934X_MBHC_MECH_DETECT_TYPE_MASK BIT(5) +#define WCD934X_MBHC_MECH_DETECT_TYPE_INS 1 +#define WCD934X_MBHC_HPHL_PLUG_TYPE_MASK BIT(4) +#define WCD934X_MBHC_HPHL_PLUG_TYPE_NO 1 +#define WCD934X_MBHC_GND_PLUG_TYPE_MASK BIT(3) +#define WCD934X_MBHC_GND_PLUG_TYPE_NO 1 +#define WCD934X_MBHC_HSL_PULLUP_COMP_EN BIT(2) +#define WCD934X_MBHC_HSG_PULLUP_COMP_EN BIT(1) +#define WCD934X_MBHC_HPHL_100K_TO_GND_EN BIT(0) #define WCD934X_ANA_MBHC_ELECT 0x0615 +#define WCD934X_ANA_MBHC_BIAS_EN_MASK BIT(0) +#define WCD934X_ANA_MBHC_BIAS_EN BIT(0) #define WCD934X_ANA_MBHC_ZDET 0x0616 #define WCD934X_ANA_MBHC_RESULT_1 0x0617 #define WCD934X_ANA_MBHC_RESULT_2 0x0618 #define WCD934X_ANA_MBHC_RESULT_3 0x0619 +#define WCD934X_ANA_MBHC_BTN0 0x061a +#define WCD934X_VTH_MASK GENMASK(7, 2) +#define WCD934X_ANA_MBHC_BTN1 0x061b +#define WCD934X_ANA_MBHC_BTN2 0x061c +#define WCD934X_ANA_MBHC_BTN3 0x061d +#define WCD934X_ANA_MBHC_BTN4 0x061e +#define WCD934X_ANA_MBHC_BTN5 0x061f +#define WCD934X_ANA_MBHC_BTN6 0x0620 +#define WCD934X_ANA_MBHC_BTN7 0x0621 +#define WCD934X_MBHC_BTN_VTH_MASK GENMASK(7, 2) #define WCD934X_ANA_MICB1 0x0622 #define WCD934X_MICB_VAL_MASK GENMASK(5, 0) #define WCD934X_ANA_MICB_EN_MASK GENMASK(7, 6) +#define WCD934X_MICB_DISABLE 0 +#define WCD934X_MICB_ENABLE 1 +#define WCD934X_MICB_PULL_UP 2 +#define WCD934X_MICB_PULL_DOWN 3 #define WCD934X_ANA_MICB_PULL_UP 0x80 #define WCD934X_ANA_MICB_ENABLE 0x40 #define WCD934X_ANA_MICB_DISABLE 0x0 #define WCD934X_ANA_MICB2 0x0623 +#define WCD934X_ANA_MICB2_ENABLE BIT(6) +#define WCD934X_ANA_MICB2_ENABLE_MASK GENMASK(7, 6) +#define WCD934X_ANA_MICB2_VOUT_MASK GENMASK(5, 0) +#define WCD934X_ANA_MICB2_RAMP 0x0624 +#define WCD934X_RAMP_EN_MASK BIT(7) +#define WCD934X_RAMP_SHIFT_CTRL_MASK GENMASK(4, 2) #define WCD934X_ANA_MICB3 0x0625 #define WCD934X_ANA_MICB4 0x0626 #define WCD934X_BIAS_VBG_FINE_ADJ 0x0629 +#define WCD934X_MBHC_CTL_CLK 0x0656 +#define WCD934X_MBHC_CTL_BCS 0x065a +#define WCD934X_MBHC_STATUS_SPARE_1 0x065b #define WCD934X_MICB1_TEST_CTL_1 0x066b #define WCD934X_MICB1_TEST_CTL_2 0x066c #define WCD934X_MICB2_TEST_CTL_1 0x066e @@ -141,7 +180,11 @@ #define WCD934X_HPH_CNP_WG_CTL 0x06cc #define WCD934X_HPH_GM3_BOOST_EN_MASK BIT(7) #define WCD934X_HPH_GM3_BOOST_ENABLE BIT(7) +#define WCD934X_HPH_CNP_WG_TIME 0x06cd #define WCD934X_HPH_OCP_CTL 0x06ce +#define WCD934X_HPH_PA_CTL2 0x06d2 +#define WCD934X_HPHPA_GND_R_MASK BIT(6) +#define WCD934X_HPHPA_GND_L_MASK BIT(4) #define WCD934X_HPH_L_EN 0x06d3 #define WCD934X_HPH_GAIN_SRC_SEL_MASK BIT(5) #define WCD934X_HPH_GAIN_SRC_SEL_COMPANDER 0 @@ -152,6 +195,8 @@ #define WCD934X_HPH_OCP_DET_MASK BIT(0) #define WCD934X_HPH_OCP_DET_ENABLE BIT(0) #define WCD934X_HPH_OCP_DET_DISABLE 0 +#define WCD934X_HPH_R_ATEST 0x06d8 +#define WCD934X_HPHPA_GND_OVR_MASK BIT(1) #define WCD934X_DIFF_LO_LO2_COMPANDER 0x06ea #define WCD934X_DIFF_LO_LO1_COMPANDER 0x06eb #define WCD934X_CLK_SYS_MCLK_PRG 0x0711 @@ -172,7 +217,19 @@ #define WCD934X_SIDO_NEW_VOUT_D_FREQ2 0x071e #define WCD934X_SIDO_RIPPLE_FREQ_EN_MASK BIT(0) #define WCD934X_SIDO_RIPPLE_FREQ_ENABLE BIT(0) +#define WCD934X_MBHC_NEW_CTL_1 0x0720 +#define WCD934X_MBHC_CTL_RCO_EN_MASK BIT(7) +#define WCD935X_MBHC_CTL_RCO_EN BIT(7) #define WCD934X_MBHC_NEW_CTL_2 0x0721 +#define WCD934X_M_RTH_CTL_MASK GENMASK(3, 2) +#define WCD934X_MBHC_NEW_PLUG_DETECT_CTL 0x0722 +#define WCD934X_HSDET_PULLUP_C_MASK GENMASK(7, 6) +#define WCD934X_MBHC_NEW_ZDET_ANA_CTL 0x0723 +#define WCD934X_ZDET_RANGE_CTL_MASK GENMASK(3, 0) +#define WCD934X_ZDET_MAXV_CTL_MASK GENMASK(6, 4) +#define WCD934X_MBHC_NEW_ZDET_RAMP_CTL 0x0724 +#define WCD934X_MBHC_NEW_FSM_STATUS 0x0725 +#define WCD934X_MBHC_NEW_ADC_RESULT 0x0726 #define WCD934X_TX_NEW_AMIC_4_5_SEL 0x0727 #define WCD934X_HPH_NEW_INT_RDAC_HD2_CTL_L 0x0733 #define WCD934X_HPH_NEW_INT_RDAC_OVERRIDE_CTL 0x0735 diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 2faf0809d01f..9533ccddd22c 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -1531,6 +1531,7 @@ config SND_SOC_WCD_MBHC config SND_SOC_WCD934X tristate "WCD9340/WCD9341 Codec" depends on COMMON_CLK + select SND_SOC_WCD_MBHC depends on MFD_WCD934X help The WCD9340/9341 is a audio codec IC Integrated in diff --git a/sound/soc/codecs/wcd934x.c b/sound/soc/codecs/wcd934x.c index 046874ef490e..25124235e7e6 100644 --- a/sound/soc/codecs/wcd934x.c +++ b/sound/soc/codecs/wcd934x.c @@ -21,6 +21,7 @@ #include <sound/soc-dapm.h> #include <sound/tlv.h> #include "wcd-clsh-v2.h" +#include "wcd-mbhc-v2.h"
#define WCD934X_RATES_MASK (SNDRV_PCM_RATE_8000 | SNDRV_PCM_RATE_16000 |\ SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_48000 |\ @@ -131,6 +132,24 @@ } \ }
+/* Z value defined in milliohm */ +#define WCD934X_ZDET_VAL_32 32000 +#define WCD934X_ZDET_VAL_400 400000 +#define WCD934X_ZDET_VAL_1200 1200000 +#define WCD934X_ZDET_VAL_100K 100000000 +/* Z floating defined in ohms */ +#define WCD934X_ZDET_FLOATING_IMPEDANCE 0x0FFFFFFE + +#define WCD934X_ZDET_NUM_MEASUREMENTS 900 +#define WCD934X_MBHC_GET_C1(c) ((c & 0xC000) >> 14) +#define WCD934X_MBHC_GET_X1(x) (x & 0x3FFF) +/* Z value compared in milliOhm */ +#define WCD934X_MBHC_IS_SECOND_RAMP_REQUIRED(z) ((z > 400000) || (z < 32000)) +#define WCD934X_MBHC_ZDET_CONST (86 * 16384) +#define WCD934X_MBHC_MOISTURE_RREF R_24_KOHM +#define WCD934X_MBHC_MAX_BUTTONS (8) +#define WCD_MBHC_HS_V_MAX 1600 + #define WCD934X_INTERPOLATOR_PATH(id) \ {"RX INT" #id "_1 MIX1 INP0", "RX0", "SLIM RX0"}, \ {"RX INT" #id "_1 MIX1 INP0", "RX1", "SLIM RX1"}, \ @@ -287,12 +306,7 @@ {"AIF3_CAP Mixer", "SLIM TX" #id, "SLIM TX" #id }, \ {"SLIM TX" #id, NULL, "CDC_IF TX" #id " MUX"}
-enum { - MIC_BIAS_1 = 1, - MIC_BIAS_2, - MIC_BIAS_3, - MIC_BIAS_4 -}; +#define WCD934X_MAX_MICBIAS MIC_BIAS_4
enum { SIDO_SOURCE_INTERNAL, @@ -486,6 +500,15 @@ static struct interp_sample_rate sr_val_tbl[] = { {352800, 0xC}, };
+struct wcd934x_mbhc_zdet_param { + u16 ldo_ctl; + u16 noff; + u16 nshift; + u16 btn5; + u16 btn6; + u16 btn7; +}; + struct wcd_slim_codec_dai_data { struct list_head slim_ch_list; struct slim_stream_config sconfig; @@ -541,6 +564,18 @@ struct wcd934x_codec { int comp_enabled[COMPANDER_MAX]; int sysclk_users; struct mutex sysclk_mutex; + /* mbhc module */ + struct wcd_mbhc *mbhc; + struct wcd_mbhc_config mbhc_cfg; + struct wcd_mbhc_intr intr_ids; + bool mbhc_started; + struct mutex micb_lock; + u32 micb_ref[WCD934X_MAX_MICBIAS]; + u32 pullup_ref[WCD934X_MAX_MICBIAS]; + u32 micb1_mv; + u32 micb2_mv; + u32 micb3_mv; + u32 micb4_mv; };
#define to_wcd934x_codec(_hw) container_of(_hw, struct wcd934x_codec, hw) @@ -1183,6 +1218,57 @@ static const struct soc_enum cdc_if_tx13_mux_enum = SOC_ENUM_SINGLE(WCD934X_DATA_HUB_SB_TX13_INP_CFG, 0, ARRAY_SIZE(cdc_if_tx13_mux_text), cdc_if_tx13_mux_text);
+static struct wcd_mbhc_field wcd_mbhc_fields[WCD_MBHC_REG_FUNC_MAX] = { + WCD_MBHC_FIELD(WCD_MBHC_L_DET_EN, WCD934X_ANA_MBHC_MECH, 0x80), + WCD_MBHC_FIELD(WCD_MBHC_GND_DET_EN, WCD934X_ANA_MBHC_MECH, 0x40), + WCD_MBHC_FIELD(WCD_MBHC_MECH_DETECTION_TYPE, WCD934X_ANA_MBHC_MECH, 0x20), + WCD_MBHC_FIELD(WCD_MBHC_MIC_CLAMP_CTL, WCD934X_MBHC_NEW_PLUG_DETECT_CTL, 0x30), + WCD_MBHC_FIELD(WCD_MBHC_ELECT_DETECTION_TYPE, WCD934X_ANA_MBHC_ELECT, 0x08), + WCD_MBHC_FIELD(WCD_MBHC_HS_L_DET_PULL_UP_CTRL, WCD934X_MBHC_NEW_PLUG_DETECT_CTL, 0xC0), + WCD_MBHC_FIELD(WCD_MBHC_HS_L_DET_PULL_UP_COMP_CTRL, WCD934X_ANA_MBHC_MECH, 0x04), + WCD_MBHC_FIELD(WCD_MBHC_HPHL_PLUG_TYPE, WCD934X_ANA_MBHC_MECH, 0x10), + WCD_MBHC_FIELD(WCD_MBHC_GND_PLUG_TYPE, WCD934X_ANA_MBHC_MECH, 0x08), + WCD_MBHC_FIELD(WCD_MBHC_SW_HPH_LP_100K_TO_GND, WCD934X_ANA_MBHC_MECH, 0x01), + WCD_MBHC_FIELD(WCD_MBHC_ELECT_SCHMT_ISRC, WCD934X_ANA_MBHC_ELECT, 0x06), + WCD_MBHC_FIELD(WCD_MBHC_FSM_EN, WCD934X_ANA_MBHC_ELECT, 0x80), + WCD_MBHC_FIELD(WCD_MBHC_INSREM_DBNC, WCD934X_MBHC_NEW_PLUG_DETECT_CTL, 0x0F), + WCD_MBHC_FIELD(WCD_MBHC_BTN_DBNC, WCD934X_MBHC_NEW_CTL_1, 0x03), + WCD_MBHC_FIELD(WCD_MBHC_HS_VREF, WCD934X_MBHC_NEW_CTL_2, 0x03), + WCD_MBHC_FIELD(WCD_MBHC_HS_COMP_RESULT, WCD934X_ANA_MBHC_RESULT_3, 0x08), + WCD_MBHC_FIELD(WCD_MBHC_IN2P_CLAMP_STATE, WCD934X_ANA_MBHC_RESULT_3, 0x10), + WCD_MBHC_FIELD(WCD_MBHC_MIC_SCHMT_RESULT, WCD934X_ANA_MBHC_RESULT_3, 0x20), + WCD_MBHC_FIELD(WCD_MBHC_HPHL_SCHMT_RESULT, WCD934X_ANA_MBHC_RESULT_3, 0x80), + WCD_MBHC_FIELD(WCD_MBHC_HPHR_SCHMT_RESULT, WCD934X_ANA_MBHC_RESULT_3, 0x40), + WCD_MBHC_FIELD(WCD_MBHC_OCP_FSM_EN, WCD934X_HPH_OCP_CTL, 0x10), + WCD_MBHC_FIELD(WCD_MBHC_BTN_RESULT, WCD934X_ANA_MBHC_RESULT_3, 0x07), + WCD_MBHC_FIELD(WCD_MBHC_BTN_ISRC_CTL, WCD934X_ANA_MBHC_ELECT, 0x70), + WCD_MBHC_FIELD(WCD_MBHC_ELECT_RESULT, WCD934X_ANA_MBHC_RESULT_3, 0xFF), + WCD_MBHC_FIELD(WCD_MBHC_MICB_CTRL, WCD934X_ANA_MICB2, 0xC0), + WCD_MBHC_FIELD(WCD_MBHC_HPH_CNP_WG_TIME, WCD934X_HPH_CNP_WG_TIME, 0xFF), + WCD_MBHC_FIELD(WCD_MBHC_HPHR_PA_EN, WCD934X_ANA_HPH, 0x40), + WCD_MBHC_FIELD(WCD_MBHC_HPHL_PA_EN, WCD934X_ANA_HPH, 0x80), + WCD_MBHC_FIELD(WCD_MBHC_HPH_PA_EN, WCD934X_ANA_HPH, 0xC0), + WCD_MBHC_FIELD(WCD_MBHC_SWCH_LEVEL_REMOVE, WCD934X_ANA_MBHC_RESULT_3, 0x10), + WCD_MBHC_FIELD(WCD_MBHC_ANC_DET_EN, WCD934X_MBHC_CTL_BCS, 0x02), + WCD_MBHC_FIELD(WCD_MBHC_FSM_STATUS, WCD934X_MBHC_STATUS_SPARE_1, 0x01), + WCD_MBHC_FIELD(WCD_MBHC_MUX_CTL, WCD934X_MBHC_NEW_CTL_2, 0x70), + WCD_MBHC_FIELD(WCD_MBHC_MOISTURE_STATUS, WCD934X_MBHC_NEW_FSM_STATUS, 0x20), + WCD_MBHC_FIELD(WCD_MBHC_HPHR_GND, WCD934X_HPH_PA_CTL2, 0x40), + WCD_MBHC_FIELD(WCD_MBHC_HPHL_GND, WCD934X_HPH_PA_CTL2, 0x10), + WCD_MBHC_FIELD(WCD_MBHC_HPHL_OCP_DET_EN, WCD934X_HPH_L_TEST, 0x01), + WCD_MBHC_FIELD(WCD_MBHC_HPHR_OCP_DET_EN, WCD934X_HPH_R_TEST, 0x01), + WCD_MBHC_FIELD(WCD_MBHC_HPHL_OCP_STATUS, WCD934X_INTR_PIN1_STATUS0, 0x04), + WCD_MBHC_FIELD(WCD_MBHC_HPHR_OCP_STATUS, WCD934X_INTR_PIN1_STATUS0, 0x08), + WCD_MBHC_FIELD(WCD_MBHC_ADC_EN, WCD934X_MBHC_NEW_CTL_1, 0x08), + WCD_MBHC_FIELD(WCD_MBHC_ADC_COMPLETE, WCD934X_MBHC_NEW_FSM_STATUS, 0x40), + WCD_MBHC_FIELD(WCD_MBHC_ADC_TIMEOUT, WCD934X_MBHC_NEW_FSM_STATUS, 0x80), + WCD_MBHC_FIELD(WCD_MBHC_ADC_RESULT, WCD934X_MBHC_NEW_ADC_RESULT, 0xFF), + WCD_MBHC_FIELD(WCD_MBHC_MICB2_VOUT, WCD934X_ANA_MICB2, 0x3F), + WCD_MBHC_FIELD(WCD_MBHC_ADC_MODE, WCD934X_MBHC_NEW_CTL_1, 0x10), + WCD_MBHC_FIELD(WCD_MBHC_DETECTION_DONE, WCD934X_MBHC_NEW_CTL_1, 0x04), + WCD_MBHC_FIELD(WCD_MBHC_ELECT_ISRC_EN, WCD934X_ANA_MBHC_ZDET, 0x02), +}; + static int wcd934x_set_sido_input_src(struct wcd934x_codec *wcd, int sido_src) { if (sido_src == wcd->sido_input_src) @@ -2127,7 +2213,8 @@ static struct clk *wcd934x_register_mclk_output(struct wcd934x_codec *wcd) return NULL; }
-static int wcd934x_get_micbias_val(struct device *dev, const char *micbias) +static int wcd934x_get_micbias_val(struct device *dev, const char *micbias, + u32 *micb_mv) { int mv;
@@ -2145,6 +2232,8 @@ static int wcd934x_get_micbias_val(struct device *dev, const char *micbias) mv = WCD934X_DEF_MICBIAS_MV; }
+ *micb_mv = mv; + return (mv - 1000) / 50; }
@@ -2155,13 +2244,17 @@ static int wcd934x_init_dmic(struct snd_soc_component *comp) u32 def_dmic_rate, dmic_clk_drv;
vout_ctl_1 = wcd934x_get_micbias_val(comp->dev, - "qcom,micbias1-microvolt"); + "qcom,micbias1-microvolt", + &wcd->micb1_mv); vout_ctl_2 = wcd934x_get_micbias_val(comp->dev, - "qcom,micbias2-microvolt"); + "qcom,micbias2-microvolt", + &wcd->micb2_mv); vout_ctl_3 = wcd934x_get_micbias_val(comp->dev, - "qcom,micbias3-microvolt"); + "qcom,micbias3-microvolt", + &wcd->micb3_mv); vout_ctl_4 = wcd934x_get_micbias_val(comp->dev, - "qcom,micbias4-microvolt"); + "qcom,micbias4-microvolt", + &wcd->micb4_mv);
snd_soc_component_update_bits(comp, WCD934X_ANA_MICB1, WCD934X_MICB_VAL_MASK, vout_ctl_1); @@ -2287,6 +2380,696 @@ static irqreturn_t wcd934x_slim_irq_handler(int irq, void *data) return ret; }
+static void wcd934x_mbhc_clk_setup(struct snd_soc_component *component, + bool enable) +{ + snd_soc_component_write_field(component, WCD934X_MBHC_NEW_CTL_1, + WCD934X_MBHC_CTL_RCO_EN_MASK, enable); +} + +static void wcd934x_mbhc_mbhc_bias_control(struct snd_soc_component *component, + bool enable) +{ + snd_soc_component_write_field(component, WCD934X_ANA_MBHC_ELECT, + WCD934X_ANA_MBHC_BIAS_EN, enable); +} + +static void wcd934x_mbhc_program_btn_thr(struct snd_soc_component *component, + int *btn_low, int *btn_high, + int num_btn, bool is_micbias) +{ + int i, vth; + + if (num_btn > WCD_MBHC_DEF_BUTTONS) { + dev_err(component->dev, "%s: invalid number of buttons: %d\n", + __func__, num_btn); + return; + } + + for (i = 0; i < num_btn; i++) { + vth = ((btn_high[i] * 2) / 25) & 0x3F; + snd_soc_component_write_field(component, WCD934X_ANA_MBHC_BTN0 + i, + WCD934X_MBHC_BTN_VTH_MASK, vth); + } +} + +static bool wcd934x_mbhc_micb_en_status(struct snd_soc_component *component, int micb_num) +{ + u8 val; + + if (micb_num == MIC_BIAS_2) { + val = snd_soc_component_read_field(component, WCD934X_ANA_MICB2, + WCD934X_ANA_MICB2_ENABLE_MASK); + if (val == WCD934X_MICB_ENABLE) + return true; + } + return false; +} + +static void wcd934x_mbhc_hph_l_pull_up_control(struct snd_soc_component *component, + enum mbhc_hs_pullup_iref pull_up_cur) +{ + /* Default pull up current to 2uA */ + if (pull_up_cur < I_OFF || pull_up_cur > I_3P0_UA || + pull_up_cur == I_DEFAULT) + pull_up_cur = I_2P0_UA; + + + snd_soc_component_write_field(component, WCD934X_MBHC_NEW_PLUG_DETECT_CTL, + WCD934X_HSDET_PULLUP_C_MASK, pull_up_cur); +} + +static int wcd934x_micbias_control(struct snd_soc_component *component, + int micb_num, int req, bool is_dapm) +{ + struct wcd934x_codec *wcd934x = snd_soc_component_get_drvdata(component); + int micb_index = micb_num - 1; + u16 micb_reg; + int ret; + + switch (micb_num) { + case MIC_BIAS_1: + micb_reg = WCD934X_ANA_MICB1; + break; + case MIC_BIAS_2: + micb_reg = WCD934X_ANA_MICB2; + break; + case MIC_BIAS_3: + micb_reg = WCD934X_ANA_MICB3; + break; + case MIC_BIAS_4: + micb_reg = WCD934X_ANA_MICB4; + break; + default: + dev_err(component->dev, "%s: Invalid micbias number: %d\n", + __func__, micb_num); + return -EINVAL; + }; + mutex_lock(&wcd934x->micb_lock); + + switch (req) { + case MICB_PULLUP_ENABLE: + wcd934x->pullup_ref[micb_index]++; + if ((wcd934x->pullup_ref[micb_index] == 1) && + (wcd934x->micb_ref[micb_index] == 0)) + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, + WCD934X_MICB_PULL_UP); + break; + case MICB_PULLUP_DISABLE: + if (wcd934x->pullup_ref[micb_index] > 0) + wcd934x->pullup_ref[micb_index]--; + + if ((wcd934x->pullup_ref[micb_index] == 0) && + (wcd934x->micb_ref[micb_index] == 0)) + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, 0); + break; + case MICB_ENABLE: + wcd934x->micb_ref[micb_index]++; + if (wcd934x->micb_ref[micb_index] == 1) { + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, + WCD934X_MICB_ENABLE); + if (micb_num == MIC_BIAS_2) + wcd_mbhc_event_notify(wcd934x->mbhc, + WCD_EVENT_POST_MICBIAS_2_ON); + } + + if (micb_num == MIC_BIAS_2 && is_dapm) + wcd_mbhc_event_notify(wcd934x->mbhc, + WCD_EVENT_POST_DAPM_MICBIAS_2_ON); + break; + case MICB_DISABLE: + if (wcd934x->micb_ref[micb_index] > 0) + wcd934x->micb_ref[micb_index]--; + + if ((wcd934x->micb_ref[micb_index] == 0) && + (wcd934x->pullup_ref[micb_index] > 0)) + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, + WCD934X_MICB_PULL_UP); + else if ((wcd934x->micb_ref[micb_index] == 0) && + (wcd934x->pullup_ref[micb_index] == 0)) { + if (micb_num == MIC_BIAS_2) + wcd_mbhc_event_notify(wcd934x->mbhc, + WCD_EVENT_PRE_MICBIAS_2_OFF); + + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, 0); + if (micb_num == MIC_BIAS_2) + wcd_mbhc_event_notify(wcd934x->mbhc, + WCD_EVENT_POST_MICBIAS_2_OFF); + } + if (is_dapm && micb_num == MIC_BIAS_2) + wcd_mbhc_event_notify(wcd934x->mbhc, + WCD_EVENT_POST_DAPM_MICBIAS_2_OFF); + break; + }; + + mutex_unlock(&wcd934x->micb_lock); + + return ret; +} + +static int wcd934x_mbhc_request_micbias(struct snd_soc_component *component, + int micb_num, int req) +{ + struct wcd934x_codec *wcd = dev_get_drvdata(component->dev); + int ret; + + if (req == MICB_ENABLE) + __wcd934x_cdc_mclk_enable(wcd, true); + + ret = wcd934x_micbias_control(component, micb_num, req, false); + + if (req == MICB_DISABLE) + __wcd934x_cdc_mclk_enable(wcd, false); + + return ret; +} + +static void wcd934x_mbhc_micb_ramp_control(struct snd_soc_component *component, + bool enable) +{ + if (enable) { + snd_soc_component_write_field(component, WCD934X_ANA_MICB2_RAMP, + WCD934X_RAMP_SHIFT_CTRL_MASK, 0x3); + snd_soc_component_write_field(component, WCD934X_ANA_MICB2_RAMP, + WCD934X_RAMP_EN_MASK, 1); + } else { + snd_soc_component_write_field(component, WCD934X_ANA_MICB2_RAMP, + WCD934X_RAMP_EN_MASK, 0); + snd_soc_component_write_field(component, WCD934X_ANA_MICB2_RAMP, + WCD934X_RAMP_SHIFT_CTRL_MASK, 0); + } +} + +static int wcd934x_get_micb_vout_ctl_val(u32 micb_mv) +{ + /* min micbias voltage is 1V and maximum is 2.85V */ + if (micb_mv < 1000 || micb_mv > 2850) + return -EINVAL; + + return (micb_mv - 1000) / 50; +} + +static int wcd934x_mbhc_micb_adjust_voltage(struct snd_soc_component *component, + int req_volt, int micb_num) +{ + struct wcd934x_codec *wcd934x = snd_soc_component_get_drvdata(component); + int cur_vout_ctl, req_vout_ctl, micb_reg, micb_en, ret = 0; + + switch (micb_num) { + case MIC_BIAS_1: + micb_reg = WCD934X_ANA_MICB1; + break; + case MIC_BIAS_2: + micb_reg = WCD934X_ANA_MICB2; + break; + case MIC_BIAS_3: + micb_reg = WCD934X_ANA_MICB3; + break; + case MIC_BIAS_4: + micb_reg = WCD934X_ANA_MICB4; + break; + default: + return -EINVAL; + } + mutex_lock(&wcd934x->micb_lock); + /* + * If requested micbias voltage is same as current micbias + * voltage, then just return. Otherwise, adjust voltage as + * per requested value. If micbias is already enabled, then + * to avoid slow micbias ramp-up or down enable pull-up + * momentarily, change the micbias value and then re-enable + * micbias. + */ + micb_en = snd_soc_component_read_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK); + cur_vout_ctl = snd_soc_component_read_field(component, micb_reg, + WCD934X_MICB_VAL_MASK); + + req_vout_ctl = wcd934x_get_micb_vout_ctl_val(req_volt); + if (req_vout_ctl < 0) { + ret = -EINVAL; + goto exit; + } + + if (cur_vout_ctl == req_vout_ctl) { + ret = 0; + goto exit; + } + + if (micb_en == WCD934X_MICB_ENABLE) + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, + WCD934X_MICB_PULL_UP); + + snd_soc_component_write_field(component, micb_reg, + WCD934X_MICB_VAL_MASK, + req_vout_ctl); + + if (micb_en == WCD934X_MICB_ENABLE) { + snd_soc_component_write_field(component, micb_reg, + WCD934X_ANA_MICB_EN_MASK, + WCD934X_MICB_ENABLE); + /* + * Add 2ms delay as per HW requirement after enabling + * micbias + */ + usleep_range(2000, 2100); + } +exit: + mutex_unlock(&wcd934x->micb_lock); + return ret; +} + +static int wcd934x_mbhc_micb_ctrl_threshold_mic(struct snd_soc_component *component, + int micb_num, bool req_en) +{ + struct wcd934x_codec *wcd934x = snd_soc_component_get_drvdata(component); + int rc, micb_mv; + + if (micb_num != MIC_BIAS_2) + return -EINVAL; + /* + * If device tree micbias level is already above the minimum + * voltage needed to detect threshold microphone, then do + * not change the micbias, just return. + */ + if (wcd934x->micb2_mv >= WCD_MBHC_THR_HS_MICB_MV) + return 0; + + micb_mv = req_en ? WCD_MBHC_THR_HS_MICB_MV : wcd934x->micb2_mv; + + rc = wcd934x_mbhc_micb_adjust_voltage(component, micb_mv, MIC_BIAS_2); + + return rc; +} + +static inline void wcd934x_mbhc_get_result_params(struct wcd934x_codec *wcd934x, + s16 *d1_a, u16 noff, + int32_t *zdet) +{ + int i; + int val, val1; + s16 c1; + s32 x1, d1; + int32_t denom; + int minCode_param[] = { + 3277, 1639, 820, 410, 205, 103, 52, 26 + }; + + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ZDET, 0x20, 0x20); + for (i = 0; i < WCD934X_ZDET_NUM_MEASUREMENTS; i++) { + regmap_read(wcd934x->regmap, WCD934X_ANA_MBHC_RESULT_2, &val); + if (val & 0x80) + break; + } + val = val << 0x8; + regmap_read(wcd934x->regmap, WCD934X_ANA_MBHC_RESULT_1, &val1); + val |= val1; + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ZDET, 0x20, 0x00); + x1 = WCD934X_MBHC_GET_X1(val); + c1 = WCD934X_MBHC_GET_C1(val); + /* If ramp is not complete, give additional 5ms */ + if ((c1 < 2) && x1) + usleep_range(5000, 5050); + + if (!c1 || !x1) { + dev_err(wcd934x->dev, "%s: Impedance detect ramp error, c1=%d, x1=0x%x\n", + __func__, c1, x1); + goto ramp_down; + } + d1 = d1_a[c1]; + denom = (x1 * d1) - (1 << (14 - noff)); + if (denom > 0) + *zdet = (WCD934X_MBHC_ZDET_CONST * 1000) / denom; + else if (x1 < minCode_param[noff]) + *zdet = WCD934X_ZDET_FLOATING_IMPEDANCE; + + dev_info(wcd934x->dev, "%s: d1=%d, c1=%d, x1=0x%x, z_val=%d(milliOhm)\n", + __func__, d1, c1, x1, *zdet); +ramp_down: + i = 0; + + while (x1) { + regmap_read(wcd934x->regmap, WCD934X_ANA_MBHC_RESULT_1, &val); + regmap_read(wcd934x->regmap, WCD934X_ANA_MBHC_RESULT_2, &val1); + val = val << 0x08; + val |= val1; + x1 = WCD934X_MBHC_GET_X1(val); + i++; + if (i == WCD934X_ZDET_NUM_MEASUREMENTS) + break; + } +} + +static void wcd934x_mbhc_zdet_ramp(struct snd_soc_component *component, + struct wcd934x_mbhc_zdet_param *zdet_param, + int32_t *zl, int32_t *zr, s16 *d1_a) +{ + struct wcd934x_codec *wcd934x = dev_get_drvdata(component->dev); + int32_t zdet = 0; + + snd_soc_component_write_field(component, WCD934X_MBHC_NEW_ZDET_ANA_CTL, + WCD934X_ZDET_MAXV_CTL_MASK, zdet_param->ldo_ctl); + snd_soc_component_update_bits(component, WCD934X_ANA_MBHC_BTN5, + WCD934X_VTH_MASK, zdet_param->btn5); + snd_soc_component_update_bits(component, WCD934X_ANA_MBHC_BTN6, + WCD934X_VTH_MASK, zdet_param->btn6); + snd_soc_component_update_bits(component, WCD934X_ANA_MBHC_BTN7, + WCD934X_VTH_MASK, zdet_param->btn7); + snd_soc_component_write_field(component, WCD934X_MBHC_NEW_ZDET_ANA_CTL, + WCD934X_ZDET_RANGE_CTL_MASK, zdet_param->noff); + snd_soc_component_update_bits(component, WCD934X_MBHC_NEW_ZDET_RAMP_CTL, + 0x0F, zdet_param->nshift); + + if (!zl) + goto z_right; + /* Start impedance measurement for HPH_L */ + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ZDET, 0x80, 0x80); + wcd934x_mbhc_get_result_params(wcd934x, d1_a, zdet_param->noff, &zdet); + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ZDET, 0x80, 0x00); + + *zl = zdet; + +z_right: + if (!zr) + return; + /* Start impedance measurement for HPH_R */ + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ZDET, 0x40, 0x40); + wcd934x_mbhc_get_result_params(wcd934x, d1_a, zdet_param->noff, &zdet); + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ZDET, 0x40, 0x00); + + *zr = zdet; +} + +static inline void wcd934x_wcd_mbhc_qfuse_cal(struct snd_soc_component *component, + int32_t *z_val, int flag_l_r) +{ + s16 q1; + int q1_cal; + + if (*z_val < (WCD934X_ZDET_VAL_400/1000)) + q1 = snd_soc_component_read(component, + WCD934X_CHIP_TIER_CTRL_EFUSE_VAL_OUT1 + (2 * flag_l_r)); + else + q1 = snd_soc_component_read(component, + WCD934X_CHIP_TIER_CTRL_EFUSE_VAL_OUT2 + (2 * flag_l_r)); + if (q1 & 0x80) + q1_cal = (10000 - ((q1 & 0x7F) * 25)); + else + q1_cal = (10000 + (q1 * 25)); + if (q1_cal > 0) + *z_val = ((*z_val) * 10000) / q1_cal; +} + +static void wcd934x_wcd_mbhc_calc_impedance(struct snd_soc_component *component, + uint32_t *zl, uint32_t *zr) +{ + struct wcd934x_codec *wcd934x = dev_get_drvdata(component->dev); + s16 reg0, reg1, reg2, reg3, reg4; + int32_t z1L, z1R, z1Ls; + int zMono, z_diff1, z_diff2; + bool is_fsm_disable = false; + struct wcd934x_mbhc_zdet_param zdet_param[] = { + {4, 0, 4, 0x08, 0x14, 0x18}, /* < 32ohm */ + {2, 0, 3, 0x18, 0x7C, 0x90}, /* 32ohm < Z < 400ohm */ + {1, 4, 5, 0x18, 0x7C, 0x90}, /* 400ohm < Z < 1200ohm */ + {1, 6, 7, 0x18, 0x7C, 0x90}, /* >1200ohm */ + }; + struct wcd934x_mbhc_zdet_param *zdet_param_ptr = NULL; + s16 d1_a[][4] = { + {0, 30, 90, 30}, + {0, 30, 30, 5}, + {0, 30, 30, 5}, + {0, 30, 30, 5}, + }; + s16 *d1 = NULL; + + reg0 = snd_soc_component_read(component, WCD934X_ANA_MBHC_BTN5); + reg1 = snd_soc_component_read(component, WCD934X_ANA_MBHC_BTN6); + reg2 = snd_soc_component_read(component, WCD934X_ANA_MBHC_BTN7); + reg3 = snd_soc_component_read(component, WCD934X_MBHC_CTL_CLK); + reg4 = snd_soc_component_read(component, WCD934X_MBHC_NEW_ZDET_ANA_CTL); + + if (snd_soc_component_read(component, WCD934X_ANA_MBHC_ELECT) & 0x80) { + is_fsm_disable = true; + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ELECT, 0x80, 0x00); + } + + /* For NO-jack, disable L_DET_EN before Z-det measurements */ + if (wcd934x->mbhc_cfg.hphl_swh) + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_MECH, 0x80, 0x00); + + /* Turn off 100k pull down on HPHL */ + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_MECH, 0x01, 0x00); + + /* First get impedance on Left */ + d1 = d1_a[1]; + zdet_param_ptr = &zdet_param[1]; + wcd934x_mbhc_zdet_ramp(component, zdet_param_ptr, &z1L, NULL, d1); + + if (!WCD934X_MBHC_IS_SECOND_RAMP_REQUIRED(z1L)) + goto left_ch_impedance; + + /* Second ramp for left ch */ + if (z1L < WCD934X_ZDET_VAL_32) { + zdet_param_ptr = &zdet_param[0]; + d1 = d1_a[0]; + } else if ((z1L > WCD934X_ZDET_VAL_400) && + (z1L <= WCD934X_ZDET_VAL_1200)) { + zdet_param_ptr = &zdet_param[2]; + d1 = d1_a[2]; + } else if (z1L > WCD934X_ZDET_VAL_1200) { + zdet_param_ptr = &zdet_param[3]; + d1 = d1_a[3]; + } + wcd934x_mbhc_zdet_ramp(component, zdet_param_ptr, &z1L, NULL, d1); + +left_ch_impedance: + if ((z1L == WCD934X_ZDET_FLOATING_IMPEDANCE) || + (z1L > WCD934X_ZDET_VAL_100K)) { + *zl = WCD934X_ZDET_FLOATING_IMPEDANCE; + zdet_param_ptr = &zdet_param[1]; + d1 = d1_a[1]; + } else { + *zl = z1L/1000; + wcd934x_wcd_mbhc_qfuse_cal(component, zl, 0); + } + dev_info(component->dev, "%s: impedance on HPH_L = %d(ohms)\n", + __func__, *zl); + + /* Start of right impedance ramp and calculation */ + wcd934x_mbhc_zdet_ramp(component, zdet_param_ptr, NULL, &z1R, d1); + if (WCD934X_MBHC_IS_SECOND_RAMP_REQUIRED(z1R)) { + if (((z1R > WCD934X_ZDET_VAL_1200) && + (zdet_param_ptr->noff == 0x6)) || + ((*zl) != WCD934X_ZDET_FLOATING_IMPEDANCE)) + goto right_ch_impedance; + /* Second ramp for right ch */ + if (z1R < WCD934X_ZDET_VAL_32) { + zdet_param_ptr = &zdet_param[0]; + d1 = d1_a[0]; + } else if ((z1R > WCD934X_ZDET_VAL_400) && + (z1R <= WCD934X_ZDET_VAL_1200)) { + zdet_param_ptr = &zdet_param[2]; + d1 = d1_a[2]; + } else if (z1R > WCD934X_ZDET_VAL_1200) { + zdet_param_ptr = &zdet_param[3]; + d1 = d1_a[3]; + } + wcd934x_mbhc_zdet_ramp(component, zdet_param_ptr, NULL, &z1R, d1); + } +right_ch_impedance: + if ((z1R == WCD934X_ZDET_FLOATING_IMPEDANCE) || + (z1R > WCD934X_ZDET_VAL_100K)) { + *zr = WCD934X_ZDET_FLOATING_IMPEDANCE; + } else { + *zr = z1R/1000; + wcd934x_wcd_mbhc_qfuse_cal(component, zr, 1); + } + dev_err(component->dev, "%s: impedance on HPH_R = %d(ohms)\n", + __func__, *zr); + + /* Mono/stereo detection */ + if ((*zl == WCD934X_ZDET_FLOATING_IMPEDANCE) && + (*zr == WCD934X_ZDET_FLOATING_IMPEDANCE)) { + dev_dbg(component->dev, + "%s: plug type is invalid or extension cable\n", + __func__); + goto zdet_complete; + } + if ((*zl == WCD934X_ZDET_FLOATING_IMPEDANCE) || + (*zr == WCD934X_ZDET_FLOATING_IMPEDANCE) || + ((*zl < WCD_MONO_HS_MIN_THR) && (*zr > WCD_MONO_HS_MIN_THR)) || + ((*zl > WCD_MONO_HS_MIN_THR) && (*zr < WCD_MONO_HS_MIN_THR))) { + dev_dbg(component->dev, + "%s: Mono plug type with one ch floating or shorted to GND\n", + __func__); + wcd_mbhc_set_hph_type(wcd934x->mbhc, WCD_MBHC_HPH_MONO); + goto zdet_complete; + } + snd_soc_component_write_field(component, WCD934X_HPH_R_ATEST, + WCD934X_HPHPA_GND_OVR_MASK, 1); + snd_soc_component_write_field(component, WCD934X_HPH_PA_CTL2, + WCD934X_HPHPA_GND_R_MASK, 1); + if (*zl < (WCD934X_ZDET_VAL_32/1000)) + wcd934x_mbhc_zdet_ramp(component, &zdet_param[0], &z1Ls, NULL, d1); + else + wcd934x_mbhc_zdet_ramp(component, &zdet_param[1], &z1Ls, NULL, d1); + snd_soc_component_write_field(component, WCD934X_HPH_PA_CTL2, + WCD934X_HPHPA_GND_R_MASK, 0); + snd_soc_component_write_field(component, WCD934X_HPH_R_ATEST, + WCD934X_HPHPA_GND_OVR_MASK, 0); + z1Ls /= 1000; + wcd934x_wcd_mbhc_qfuse_cal(component, &z1Ls, 0); + /* Parallel of left Z and 9 ohm pull down resistor */ + zMono = ((*zl) * 9) / ((*zl) + 9); + z_diff1 = (z1Ls > zMono) ? (z1Ls - zMono) : (zMono - z1Ls); + z_diff2 = ((*zl) > z1Ls) ? ((*zl) - z1Ls) : (z1Ls - (*zl)); + if ((z_diff1 * (*zl + z1Ls)) > (z_diff2 * (z1Ls + zMono))) { + dev_err(component->dev, "%s: stereo plug type detected\n", + __func__); + wcd_mbhc_set_hph_type(wcd934x->mbhc, WCD_MBHC_HPH_STEREO); + } else { + dev_err(component->dev, "%s: MONO plug type detected\n", + __func__); + wcd_mbhc_set_hph_type(wcd934x->mbhc, WCD_MBHC_HPH_MONO); + } + +zdet_complete: + snd_soc_component_write(component, WCD934X_ANA_MBHC_BTN5, reg0); + snd_soc_component_write(component, WCD934X_ANA_MBHC_BTN6, reg1); + snd_soc_component_write(component, WCD934X_ANA_MBHC_BTN7, reg2); + /* Turn on 100k pull down on HPHL */ + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_MECH, 0x01, 0x01); + + /* For NO-jack, re-enable L_DET_EN after Z-det measurements */ + if (wcd934x->mbhc_cfg.hphl_swh) + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_MECH, 0x80, 0x80); + + snd_soc_component_write(component, WCD934X_MBHC_NEW_ZDET_ANA_CTL, reg4); + snd_soc_component_write(component, WCD934X_MBHC_CTL_CLK, reg3); + if (is_fsm_disable) + regmap_update_bits(wcd934x->regmap, WCD934X_ANA_MBHC_ELECT, 0x80, 0x80); +} + +static void wcd934x_mbhc_gnd_det_ctrl(struct snd_soc_component *component, + bool enable) +{ + if (enable) { + snd_soc_component_write_field(component, WCD934X_ANA_MBHC_MECH, + WCD934X_MBHC_HSG_PULLUP_COMP_EN, 1); + snd_soc_component_write_field(component, WCD934X_ANA_MBHC_MECH, + WCD934X_MBHC_GND_DET_EN_MASK, 1); + } else { + snd_soc_component_write_field(component, WCD934X_ANA_MBHC_MECH, + WCD934X_MBHC_GND_DET_EN_MASK, 0); + snd_soc_component_write_field(component, WCD934X_ANA_MBHC_MECH, + WCD934X_MBHC_HSG_PULLUP_COMP_EN, 0); + } +} + +static void wcd934x_mbhc_hph_pull_down_ctrl(struct snd_soc_component *component, + bool enable) +{ + snd_soc_component_write_field(component, WCD934X_HPH_PA_CTL2, + WCD934X_HPHPA_GND_R_MASK, enable); + snd_soc_component_write_field(component, WCD934X_HPH_PA_CTL2, + WCD934X_HPHPA_GND_L_MASK, enable); +} + +static const struct wcd_mbhc_cb mbhc_cb = { + .clk_setup = wcd934x_mbhc_clk_setup, + .mbhc_bias = wcd934x_mbhc_mbhc_bias_control, + .set_btn_thr = wcd934x_mbhc_program_btn_thr, + .micbias_enable_status = wcd934x_mbhc_micb_en_status, + .hph_pull_up_control = wcd934x_mbhc_hph_l_pull_up_control, + .mbhc_micbias_control = wcd934x_mbhc_request_micbias, + .mbhc_micb_ramp_control = wcd934x_mbhc_micb_ramp_control, + .mbhc_micb_ctrl_thr_mic = wcd934x_mbhc_micb_ctrl_threshold_mic, + .compute_impedance = wcd934x_wcd_mbhc_calc_impedance, + .mbhc_gnd_det_ctrl = wcd934x_mbhc_gnd_det_ctrl, + .hph_pull_down_ctrl = wcd934x_mbhc_hph_pull_down_ctrl, +}; + +static int wcd934x_get_hph_type(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); + struct wcd934x_codec *wcd = snd_soc_component_get_drvdata(component); + + ucontrol->value.integer.value[0] = wcd_mbhc_get_hph_type(wcd->mbhc); + + return 0; +} + +static int wcd934x_hph_impedance_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + uint32_t zl, zr; + bool hphr; + struct soc_mixer_control *mc; + struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); + struct wcd934x_codec *wcd = snd_soc_component_get_drvdata(component); + + mc = (struct soc_mixer_control *)(kcontrol->private_value); + hphr = mc->shift; + wcd_mbhc_get_impedance(wcd->mbhc, &zl, &zr); + dev_dbg(component->dev, "%s: zl=%u(ohms), zr=%u(ohms)\n", __func__, zl, zr); + ucontrol->value.integer.value[0] = hphr ? zr : zl; + + return 0; +} +static const struct snd_kcontrol_new hph_type_detect_controls[] = { + SOC_SINGLE_EXT("HPH Type", 0, 0, UINT_MAX, 0, + wcd934x_get_hph_type, NULL), +}; + +static const struct snd_kcontrol_new impedance_detect_controls[] = { + SOC_SINGLE_EXT("HPHL Impedance", 0, 0, UINT_MAX, 0, + wcd934x_hph_impedance_get, NULL), + SOC_SINGLE_EXT("HPHR Impedance", 0, 1, UINT_MAX, 0, + wcd934x_hph_impedance_get, NULL), +}; + +static int wcd934x_mbhc_init(struct snd_soc_component *component) +{ + struct wcd934x_ddata *data = dev_get_drvdata(component->dev->parent); + struct wcd934x_codec *wcd = snd_soc_component_get_drvdata(component); + struct wcd_mbhc_intr *intr_ids = &wcd->intr_ids; + + intr_ids->mbhc_sw_intr = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_MBHC_SW_DET); + intr_ids->mbhc_btn_press_intr = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_MBHC_BUTTON_PRESS_DET); + intr_ids->mbhc_btn_release_intr = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_MBHC_BUTTON_RELEASE_DET); + intr_ids->mbhc_hs_ins_intr = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_MBHC_ELECT_INS_REM_LEG_DET); + intr_ids->mbhc_hs_rem_intr = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_MBHC_ELECT_INS_REM_DET); + intr_ids->hph_left_ocp = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_HPH_PA_OCPL_FAULT); + intr_ids->hph_right_ocp = regmap_irq_get_virq(data->irq_data, + WCD934X_IRQ_HPH_PA_OCPR_FAULT); + + wcd->mbhc = wcd_mbhc_init(component, &mbhc_cb, intr_ids, wcd_mbhc_fields, true); + if (IS_ERR(wcd->mbhc)) { + wcd->mbhc = NULL; + return -EINVAL; + } + + snd_soc_add_component_controls(component, impedance_detect_controls, + ARRAY_SIZE(impedance_detect_controls)); + snd_soc_add_component_controls(component, hph_type_detect_controls, + ARRAY_SIZE(hph_type_detect_controls)); + + return 0; +} static int wcd934x_comp_probe(struct snd_soc_component *component) { struct wcd934x_codec *wcd = dev_get_drvdata(component->dev); @@ -2309,6 +3092,10 @@ static int wcd934x_comp_probe(struct snd_soc_component *component) INIT_LIST_HEAD(&wcd->dai[i].slim_ch_list);
wcd934x_init_dmic(component); + + if (wcd934x_mbhc_init(component)) + dev_err(component->dev, "Failed to Initialize MBHC\n"); + return 0; }
@@ -3756,6 +4543,7 @@ static int wcd934x_codec_enable_hphl_pa(struct snd_soc_dapm_widget *w, int event) { struct snd_soc_component *comp = snd_soc_dapm_to_component(w->dapm); + struct wcd934x_codec *wcd = snd_soc_component_get_drvdata(comp);
switch (event) { case SND_SOC_DAPM_POST_PMU: @@ -3788,6 +4576,7 @@ static int wcd934x_codec_enable_hphl_pa(struct snd_soc_dapm_widget *w, WCD934X_CDC_RX_PGA_MUTE_EN_MASK, 0x00); break; case SND_SOC_DAPM_PRE_PMD: + wcd_mbhc_event_notify(wcd->mbhc, WCD_EVENT_POST_HPHL_PA_OFF); /* Enable DSD Mute before PA disable */ snd_soc_component_update_bits(comp, WCD934X_HPH_L_TEST, WCD934X_HPH_OCP_DET_MASK, @@ -3806,6 +4595,7 @@ static int wcd934x_codec_enable_hphl_pa(struct snd_soc_dapm_widget *w, * disabled, then 20ms delay is needed after PA disable. */ usleep_range(20000, 20100); + wcd_mbhc_event_notify(wcd->mbhc, WCD_EVENT_POST_HPHL_PA_OFF); break; }
@@ -3817,6 +4607,7 @@ static int wcd934x_codec_enable_hphr_pa(struct snd_soc_dapm_widget *w, int event) { struct snd_soc_component *comp = snd_soc_dapm_to_component(w->dapm); + struct wcd934x_codec *wcd = snd_soc_component_get_drvdata(comp);
switch (event) { case SND_SOC_DAPM_POST_PMU: @@ -3851,6 +4642,7 @@ static int wcd934x_codec_enable_hphr_pa(struct snd_soc_dapm_widget *w, WCD934X_CDC_RX_PGA_MUTE_DISABLE); break; case SND_SOC_DAPM_PRE_PMD: + wcd_mbhc_event_notify(wcd->mbhc, WCD_EVENT_PRE_HPHR_PA_OFF); snd_soc_component_update_bits(comp, WCD934X_HPH_R_TEST, WCD934X_HPH_OCP_DET_MASK, WCD934X_HPH_OCP_DET_DISABLE); @@ -3868,6 +4660,7 @@ static int wcd934x_codec_enable_hphr_pa(struct snd_soc_dapm_widget *w, * disabled, then 20ms delay is needed after PA disable. */ usleep_range(20000, 20100); + wcd_mbhc_event_notify(wcd->mbhc, WCD_EVENT_POST_HPHR_PA_OFF); break; }
@@ -4323,6 +5116,29 @@ static int wcd934x_codec_enable_adc(struct snd_soc_dapm_widget *w, return 0; }
+static int wcd934x_codec_enable_micbias(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, + int event) +{ + struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm); + int micb_num = w->shift; + + switch (event) { + case SND_SOC_DAPM_PRE_PMU: + wcd934x_micbias_control(component, micb_num, MICB_ENABLE, true); + break; + case SND_SOC_DAPM_POST_PMU: + /* 1 msec delay as per HW requirement */ + usleep_range(1000, 1100); + break; + case SND_SOC_DAPM_POST_PMD: + wcd934x_micbias_control(component, micb_num, MICB_DISABLE, true); + break; + }; + + return 0; +} + static const struct snd_soc_dapm_widget wcd934x_dapm_widgets[] = { /* Analog Outputs */ SND_SOC_DAPM_OUTPUT("EAR"), @@ -4778,13 +5594,17 @@ static const struct snd_soc_dapm_widget wcd934x_dapm_widgets[] = { wcd934x_codec_enable_adc, SND_SOC_DAPM_PRE_PMU), SND_SOC_DAPM_ADC_E("ADC4", NULL, WCD934X_ANA_AMIC4, 7, 0, wcd934x_codec_enable_adc, SND_SOC_DAPM_PRE_PMU), - SND_SOC_DAPM_SUPPLY("MIC BIAS1", WCD934X_ANA_MICB1, 6, 0, NULL, + SND_SOC_DAPM_SUPPLY("MIC BIAS1", SND_SOC_NOPM, MIC_BIAS_1, 0, + wcd934x_codec_enable_micbias, SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD), - SND_SOC_DAPM_SUPPLY("MIC BIAS2", WCD934X_ANA_MICB2, 6, 0, NULL, + SND_SOC_DAPM_SUPPLY("MIC BIAS2", SND_SOC_NOPM, MIC_BIAS_2, 0, + wcd934x_codec_enable_micbias, SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD), - SND_SOC_DAPM_SUPPLY("MIC BIAS3", WCD934X_ANA_MICB3, 6, 0, NULL, + SND_SOC_DAPM_SUPPLY("MIC BIAS3", SND_SOC_NOPM, MIC_BIAS_3, 0, + wcd934x_codec_enable_micbias, SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD), - SND_SOC_DAPM_SUPPLY("MIC BIAS4", WCD934X_ANA_MICB4, 6, 0, NULL, + SND_SOC_DAPM_SUPPLY("MIC BIAS4", SND_SOC_NOPM, MIC_BIAS_4, 0, + wcd934x_codec_enable_micbias, SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD),
SND_SOC_DAPM_MUX("AMIC4_5 SEL", SND_SOC_NOPM, 0, 0, &tx_amic4_5), @@ -4961,6 +5781,26 @@ static const struct snd_soc_dapm_route wcd934x_audio_map[] = { {"SRC1", NULL, "IIR1"}, };
+static int wcd934x_codec_set_jack(struct snd_soc_component *comp, + struct snd_soc_jack *jack, void *data) +{ + struct wcd934x_codec *wcd = dev_get_drvdata(comp->dev); + int ret = 0; + + if (!wcd->mbhc) + return -ENOTSUPP; + + if (jack && !wcd->mbhc_started) { + ret = wcd_mbhc_start(wcd->mbhc, &wcd->mbhc_cfg, jack); + wcd->mbhc_started = true; + } else if (wcd->mbhc_started) { + wcd_mbhc_stop(wcd->mbhc); + wcd->mbhc_started = false; + } + + return ret; +} + static const struct snd_soc_component_driver wcd934x_component_drv = { .probe = wcd934x_comp_probe, .remove = wcd934x_comp_remove, @@ -4971,11 +5811,13 @@ static const struct snd_soc_component_driver wcd934x_component_drv = { .num_dapm_widgets = ARRAY_SIZE(wcd934x_dapm_widgets), .dapm_routes = wcd934x_audio_map, .num_dapm_routes = ARRAY_SIZE(wcd934x_audio_map), + .set_jack = wcd934x_codec_set_jack, };
static int wcd934x_codec_parse_data(struct wcd934x_codec *wcd) { struct device *dev = &wcd->sdev->dev; + struct wcd_mbhc_config *cfg = &wcd->mbhc_cfg; struct device_node *ifc_dev_np;
ifc_dev_np = of_parse_phandle(dev->of_node, "slim-ifc-dev", 0); @@ -5001,6 +5843,18 @@ static int wcd934x_codec_parse_data(struct wcd934x_codec *wcd) of_property_read_u32(dev->parent->of_node, "qcom,dmic-sample-rate", &wcd->dmic_sample_rate);
+ cfg->mbhc_micbias = MIC_BIAS_2; + cfg->anc_micbias = MIC_BIAS_2; + cfg->v_hs_max = WCD_MBHC_HS_V_MAX; + cfg->num_btn = WCD934X_MBHC_MAX_BUTTONS; + cfg->micb_mv = wcd->micb2_mv; + cfg->linein_th = 5000; + cfg->hs_thr = 1700; + cfg->hph_thr = 50; + + wcd_dt_parse_mbhc_data(dev, cfg); + + return 0; }
@@ -5020,6 +5874,7 @@ static int wcd934x_codec_probe(struct platform_device *pdev) wcd->extclk = data->extclk; wcd->sdev = to_slim_device(data->dev); mutex_init(&wcd->sysclk_mutex); + mutex_init(&wcd->micb_lock);
ret = wcd934x_codec_parse_data(wcd); if (ret) {
Hi Srinivas,
I love your patch! Perhaps something to improve:
[auto build test WARNING on asoc/for-next] [also build test WARNING on lee-mfd/for-mfd-next robh/for-next v5.13-rc1 next-20210510] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Srinivas-Kandagatla/ASoC-codecs-wcd... base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next config: powerpc64-randconfig-r025-20210510 (attached as .config) compiler: clang version 13.0.0 (https://github.com/llvm/llvm-project 492173d42b32cb91d5d0d72d5ed84fcab80d059a) reproduce (this is a W=1 build): wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross # install powerpc64 cross compiling tool for clang build # apt-get install binutils-powerpc64-linux-gnu # https://github.com/0day-ci/linux/commit/97c9f617d94c14ca286bf4542d74b0968a51... git remote add linux-review https://github.com/0day-ci/linux git fetch --no-tags linux-review Srinivas-Kandagatla/ASoC-codecs-wcd934x-add-Headset-and-button-detection-support/20210510-181344 git checkout 97c9f617d94c14ca286bf4542d74b0968a5176c8 # save the attached .config to linux build tree COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 ARCH=powerpc64
If you fix the issue, kindly add following tag as appropriate Reported-by: kernel test robot lkp@intel.com
All warnings (new ones prefixed by >>):
sound/soc/codecs/wcd-mbhc-v2.c:552:8: warning: variable 'jack_type' is used uninitialized whenever switch case is taken [-Wsometimes-uninitialized]
case MBHC_PLUG_TYPE_GND_MIC_SWAP: ^~~~~~~~~~~~~~~~~~~~~~~~~~~ sound/soc/codecs/wcd-mbhc-v2.c:564:33: note: uninitialized use occurs here wcd_mbhc_report_plug(mbhc, 0, jack_type); ^~~~~~~~~ sound/soc/codecs/wcd-mbhc-v2.c:503:2: note: variable 'jack_type' is declared here enum snd_jack_types jack_type; ^ 1 warning generated. --
sound/soc/codecs/wcd934x.c:2532:9: warning: variable 'ret' is uninitialized when used here [-Wuninitialized]
return ret; ^~~ sound/soc/codecs/wcd934x.c:2448:9: note: initialize the variable 'ret' to silence this warning int ret; ^ = 0 1 warning generated.
vim +/ret +2532 sound/soc/codecs/wcd934x.c
2441 2442 static int wcd934x_micbias_control(struct snd_soc_component *component, 2443 int micb_num, int req, bool is_dapm) 2444 { 2445 struct wcd934x_codec *wcd934x = snd_soc_component_get_drvdata(component); 2446 int micb_index = micb_num - 1; 2447 u16 micb_reg; 2448 int ret; 2449 2450 switch (micb_num) { 2451 case MIC_BIAS_1: 2452 micb_reg = WCD934X_ANA_MICB1; 2453 break; 2454 case MIC_BIAS_2: 2455 micb_reg = WCD934X_ANA_MICB2; 2456 break; 2457 case MIC_BIAS_3: 2458 micb_reg = WCD934X_ANA_MICB3; 2459 break; 2460 case MIC_BIAS_4: 2461 micb_reg = WCD934X_ANA_MICB4; 2462 break; 2463 default: 2464 dev_err(component->dev, "%s: Invalid micbias number: %d\n", 2465 __func__, micb_num); 2466 return -EINVAL; 2467 }; 2468 mutex_lock(&wcd934x->micb_lock); 2469 2470 switch (req) { 2471 case MICB_PULLUP_ENABLE: 2472 wcd934x->pullup_ref[micb_index]++; 2473 if ((wcd934x->pullup_ref[micb_index] == 1) && 2474 (wcd934x->micb_ref[micb_index] == 0)) 2475 snd_soc_component_write_field(component, micb_reg, 2476 WCD934X_ANA_MICB_EN_MASK, 2477 WCD934X_MICB_PULL_UP); 2478 break; 2479 case MICB_PULLUP_DISABLE: 2480 if (wcd934x->pullup_ref[micb_index] > 0) 2481 wcd934x->pullup_ref[micb_index]--; 2482 2483 if ((wcd934x->pullup_ref[micb_index] == 0) && 2484 (wcd934x->micb_ref[micb_index] == 0)) 2485 snd_soc_component_write_field(component, micb_reg, 2486 WCD934X_ANA_MICB_EN_MASK, 0); 2487 break; 2488 case MICB_ENABLE: 2489 wcd934x->micb_ref[micb_index]++; 2490 if (wcd934x->micb_ref[micb_index] == 1) { 2491 snd_soc_component_write_field(component, micb_reg, 2492 WCD934X_ANA_MICB_EN_MASK, 2493 WCD934X_MICB_ENABLE); 2494 if (micb_num == MIC_BIAS_2) 2495 wcd_mbhc_event_notify(wcd934x->mbhc, 2496 WCD_EVENT_POST_MICBIAS_2_ON); 2497 } 2498 2499 if (micb_num == MIC_BIAS_2 && is_dapm) 2500 wcd_mbhc_event_notify(wcd934x->mbhc, 2501 WCD_EVENT_POST_DAPM_MICBIAS_2_ON); 2502 break; 2503 case MICB_DISABLE: 2504 if (wcd934x->micb_ref[micb_index] > 0) 2505 wcd934x->micb_ref[micb_index]--; 2506 2507 if ((wcd934x->micb_ref[micb_index] == 0) && 2508 (wcd934x->pullup_ref[micb_index] > 0)) 2509 snd_soc_component_write_field(component, micb_reg, 2510 WCD934X_ANA_MICB_EN_MASK, 2511 WCD934X_MICB_PULL_UP); 2512 else if ((wcd934x->micb_ref[micb_index] == 0) && 2513 (wcd934x->pullup_ref[micb_index] == 0)) { 2514 if (micb_num == MIC_BIAS_2) 2515 wcd_mbhc_event_notify(wcd934x->mbhc, 2516 WCD_EVENT_PRE_MICBIAS_2_OFF); 2517 2518 snd_soc_component_write_field(component, micb_reg, 2519 WCD934X_ANA_MICB_EN_MASK, 0); 2520 if (micb_num == MIC_BIAS_2) 2521 wcd_mbhc_event_notify(wcd934x->mbhc, 2522 WCD_EVENT_POST_MICBIAS_2_OFF); 2523 } 2524 if (is_dapm && micb_num == MIC_BIAS_2) 2525 wcd_mbhc_event_notify(wcd934x->mbhc, 2526 WCD_EVENT_POST_DAPM_MICBIAS_2_OFF); 2527 break; 2528 }; 2529 2530 mutex_unlock(&wcd934x->micb_lock); 2531
2532 return ret;
2533 } 2534
--- 0-DAY CI Kernel Test Service, Intel Corporation https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org --- sound/soc/qcom/sdm845.c | 8 ++++++++ 1 file changed, 8 insertions(+)
diff --git a/sound/soc/qcom/sdm845.c b/sound/soc/qcom/sdm845.c index 153e9b2de0b5..0adfc5708949 100644 --- a/sound/soc/qcom/sdm845.c +++ b/sound/soc/qcom/sdm845.c @@ -288,6 +288,14 @@ static int sdm845_dai_init(struct snd_soc_pcm_runtime *rtd) snd_soc_dai_set_sysclk(codec_dai, 0, WCD934X_DEFAULT_MCLK_RATE, SNDRV_PCM_STREAM_PLAYBACK); + + rval = snd_soc_component_set_jack(codec_dai->component, + &pdata->jack, NULL); + if (rval != 0 && rval != -ENOTSUPP) { + dev_warn(card->dev, "Failed to set jack: %d\n", rval); + return rval; + } + } break; default:
participants (3)
-
kernel test robot -
Rob Herring -
Srinivas Kandagatla