[alsa-devel] [PATCH v6 00/18] MFD/ASoC/Input: TWL4030/TWL60X0 changes
Hello,
Changes since v5: - Use alloc_workqueue in the twl6040-vibra driver (comment from Tejun Heo) - Allow user to change the headset power mode, but if the change is not allowed by the use case the change is not written to the HW (comment from Mark Brown)
Mark: I have added your acks for the patches, except for patch 15, where you requested a change.
Intro message from the v5 series: The series will do five major things, and they are in one series, because they pretty much depending on each other, so it is easier to handle them together.
1. Move the common pmic related configurations out from the board files. New twl-common.c/h file has been created for this purpose. OMAP3 board files received two patches (pdata, and regualtor changes), OMAP4 board files has been changed with one patch.
2. Rename the twl4030-codec MFD driver to twl4030-audio Since the ASoC multicomponent introduction (2.6.37) the twl4030-codec MFD dirver had been using twl4030-audio to register (twl4030-codec is the ASoC codec driver). The documentation refers to this part of twl as audio block, so it is better to rename the driver as well to avoid confusion.
3. Introduction of MFD driver for twl6040. The TWL6040 audio IC has codec and vibra functionality. Convert the existing ASoC codec driver to use the new MFD driver's interface.
4. Vibrator driver for TWL6040 (Input/ForceFeedback driver) The driver itself, and support for the vibrators in SDP4430 board.
5. Updates for twl6040 ASoC codec driver HS ramp configuration, new ABE dais, updated sample rate constraints, SDP4430 configuration.
Regards, Peter
--- Axel Castaneda Gonzalez (1): ASoC: twl6040: Configure ramp step based on platform
Liam Girdwood (3): ASoC: twl6040: add all ABE DAIs ASoC: twl6040: Support other sample rates in constraints. ASoC: twl6040: set default constraints.
Misael Lopez Cruz (5): mfd: twl6040: Add initial support ASoC: twl6040: Convert into TWL6040 MFD child input: Add initial support for TWL6040 vibrator ASoC: twl6040: Remove pll and headset mode dependency OMAP4: SDP4430: Add twl6040 codec platform support
Peter Ujfalusi (9): OMAP: New twl-common for common TWL configuration OMAP4: Move common twl6030 configuration to twl-common OMAP3: Move common twl configuration to twl-common OMAP3: Move common regulator configuration to twl-common MFD: twl4030-codec: Rename internals from codec to audio MFD: twl4030-codec -> twl4030-audio: Rename the driver MFD: twl4030-audio: Rename platform data MFD: twl6040: Change platform data for soc codec driver OMAP4: SDP4430: Add twl6040 vibrator platform support
arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/board-3430sdp.c | 89 +--- arch/arm/mach-omap2/board-4430sdp.c | 187 ++---- arch/arm/mach-omap2/board-cm-t35.c | 48 +-- arch/arm/mach-omap2/board-devkit8000.c | 37 +-- arch/arm/mach-omap2/board-igep0020.c | 44 +-- arch/arm/mach-omap2/board-ldp.c | 15 +- arch/arm/mach-omap2/board-omap3beagle.c | 60 +-- arch/arm/mach-omap2/board-omap3evm.c | 67 +-- arch/arm/mach-omap2/board-omap3pandora.c | 59 +-- arch/arm/mach-omap2/board-omap3stalker.c | 70 +-- arch/arm/mach-omap2/board-omap3touchbook.c | 57 +-- arch/arm/mach-omap2/board-omap4panda.c | 149 +----- arch/arm/mach-omap2/board-overo.c | 59 +-- arch/arm/mach-omap2/board-rm680.c | 8 +- arch/arm/mach-omap2/board-rx51-peripherals.c | 44 +-- arch/arm/mach-omap2/board-zoom-peripherals.c | 88 +--- arch/arm/mach-omap2/common-board-devices.c | 21 - arch/arm/mach-omap2/common-board-devices.h | 26 +- arch/arm/mach-omap2/twl-common.c | 304 ++++++++++ arch/arm/mach-omap2/twl-common.h | 59 ++ arch/arm/plat-omap/include/plat/irqs.h | 12 +- drivers/input/misc/Kconfig | 13 +- drivers/input/misc/Makefile | 1 + drivers/input/misc/twl4030-vibra.c | 12 +- drivers/input/misc/twl6040-vibra.c | 416 +++++++++++++ drivers/mfd/Kconfig | 8 +- drivers/mfd/Makefile | 3 +- drivers/mfd/twl-core.c | 13 +- drivers/mfd/twl4030-audio.c | 277 +++++++++ drivers/mfd/twl4030-codec.c | 277 --------- drivers/mfd/twl6040-core.c | 601 +++++++++++++++++++ drivers/mfd/twl6040-irq.c | 205 +++++++ include/linux/i2c/twl.h | 25 +- .../linux/mfd/{twl4030-codec.h => twl4030-audio.h} | 16 +- include/linux/mfd/twl6040.h | 261 ++++++++ sound/soc/codecs/Kconfig | 3 +- sound/soc/codecs/twl4030.c | 22 +- sound/soc/codecs/twl6040.c | 628 ++++++++------------ sound/soc/codecs/twl6040.h | 118 ---- sound/soc/omap/sdp3430.c | 2 +- sound/soc/omap/sdp4430.c | 2 + sound/soc/omap/zoom2.c | 2 +- 43 files changed, 2635 insertions(+), 1775 deletions(-) create mode 100644 arch/arm/mach-omap2/twl-common.c create mode 100644 arch/arm/mach-omap2/twl-common.h create mode 100644 drivers/input/misc/twl6040-vibra.c create mode 100644 drivers/mfd/twl4030-audio.c delete mode 100644 drivers/mfd/twl4030-codec.c create mode 100644 drivers/mfd/twl6040-core.c create mode 100644 drivers/mfd/twl6040-irq.c rename include/linux/mfd/{twl4030-codec.h => twl4030-audio.h} (96%) create mode 100644 include/linux/mfd/twl6040.h
Introduce a new file, which will be used to configure common pmic (TWL) devices, regulators, and TWL audio.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/common-board-devices.c | 21 ------------- arch/arm/mach-omap2/common-board-devices.h | 26 +-------------- arch/arm/mach-omap2/twl-common.c | 46 ++++++++++++++++++++++++++++ arch/arm/mach-omap2/twl-common.h | 28 +++++++++++++++++ 5 files changed, 77 insertions(+), 46 deletions(-) create mode 100644 arch/arm/mach-omap2/twl-common.c create mode 100644 arch/arm/mach-omap2/twl-common.h
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index b148077..fee192e 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -269,4 +269,4 @@ obj-$(CONFIG_ARCH_OMAP4) += hwspinlock.o disp-$(CONFIG_OMAP2_DSS) := display.o obj-y += $(disp-m) $(disp-y)
-obj-y += common-board-devices.o +obj-y += common-board-devices.o twl-common.o diff --git a/arch/arm/mach-omap2/common-board-devices.c b/arch/arm/mach-omap2/common-board-devices.c index 94ccf46..5e03b2e 100644 --- a/arch/arm/mach-omap2/common-board-devices.c +++ b/arch/arm/mach-omap2/common-board-devices.c @@ -20,36 +20,15 @@ * */
-#include <linux/i2c.h> -#include <linux/i2c/twl.h> - #include <linux/gpio.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h>
-#include <plat/i2c.h> #include <plat/mcspi.h> #include <plat/nand.h>
#include "common-board-devices.h"
-static struct i2c_board_info __initdata pmic_i2c_board_info = { - .addr = 0x48, - .flags = I2C_CLIENT_WAKE, -}; - -void __init omap_pmic_init(int bus, u32 clkrate, - const char *pmic_type, int pmic_irq, - struct twl4030_platform_data *pmic_data) -{ - strncpy(pmic_i2c_board_info.type, pmic_type, - sizeof(pmic_i2c_board_info.type)); - pmic_i2c_board_info.irq = pmic_irq; - pmic_i2c_board_info.platform_data = pmic_data; - - omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1); -} - #if defined(CONFIG_TOUCHSCREEN_ADS7846) || \ defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) static struct omap2_mcspi_device_config ads7846_mcspi_config = { diff --git a/arch/arm/mach-omap2/common-board-devices.h b/arch/arm/mach-omap2/common-board-devices.h index 6797190..a0b4a428 100644 --- a/arch/arm/mach-omap2/common-board-devices.h +++ b/arch/arm/mach-omap2/common-board-devices.h @@ -1,33 +1,11 @@ #ifndef __OMAP_COMMON_BOARD_DEVICES__ #define __OMAP_COMMON_BOARD_DEVICES__
+#include "twl-common.h" + #define NAND_BLOCK_SIZE SZ_128K
-struct twl4030_platform_data; struct mtd_partition; - -void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq, - struct twl4030_platform_data *pmic_data); - -static inline void omap2_pmic_init(const char *pmic_type, - struct twl4030_platform_data *pmic_data) -{ - omap_pmic_init(2, 2600, pmic_type, INT_24XX_SYS_NIRQ, pmic_data); -} - -static inline void omap3_pmic_init(const char *pmic_type, - struct twl4030_platform_data *pmic_data) -{ - omap_pmic_init(1, 2600, pmic_type, INT_34XX_SYS_NIRQ, pmic_data); -} - -static inline void omap4_pmic_init(const char *pmic_type, - struct twl4030_platform_data *pmic_data) -{ - /* Phoenix Audio IC needs I2C1 to start with 400 KHz or less */ - omap_pmic_init(1, 400, pmic_type, OMAP44XX_IRQ_SYS_1N, pmic_data); -} - struct ads7846_platform_data;
void omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce, diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c new file mode 100644 index 0000000..4f7b24c --- /dev/null +++ b/arch/arm/mach-omap2/twl-common.c @@ -0,0 +1,46 @@ +/* + * twl-common.c + * + * Copyright (C) 2011 Texas Instruments, Inc.. + * Author: Peter Ujfalusi peter.ujfalusi@ti.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#include <linux/i2c.h> +#include <linux/i2c/twl.h> +#include <linux/gpio.h> + +#include <plat/i2c.h> + +#include "twl-common.h" + +static struct i2c_board_info __initdata pmic_i2c_board_info = { + .addr = 0x48, + .flags = I2C_CLIENT_WAKE, +}; + +void __init omap_pmic_init(int bus, u32 clkrate, + const char *pmic_type, int pmic_irq, + struct twl4030_platform_data *pmic_data) +{ + strncpy(pmic_i2c_board_info.type, pmic_type, + sizeof(pmic_i2c_board_info.type)); + pmic_i2c_board_info.irq = pmic_irq; + pmic_i2c_board_info.platform_data = pmic_data; + + omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1); +} diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h new file mode 100644 index 0000000..e9fe2ab --- /dev/null +++ b/arch/arm/mach-omap2/twl-common.h @@ -0,0 +1,28 @@ +#ifndef __OMAP_PMIC_COMMON__ +#define __OMAP_PMIC_COMMON__ + +struct twl4030_platform_data; + +void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq, + struct twl4030_platform_data *pmic_data); + +static inline void omap2_pmic_init(const char *pmic_type, + struct twl4030_platform_data *pmic_data) +{ + omap_pmic_init(2, 2600, pmic_type, INT_24XX_SYS_NIRQ, pmic_data); +} + +static inline void omap3_pmic_init(const char *pmic_type, + struct twl4030_platform_data *pmic_data) +{ + omap_pmic_init(1, 2600, pmic_type, INT_34XX_SYS_NIRQ, pmic_data); +} + +static inline void omap4_pmic_init(const char *pmic_type, + struct twl4030_platform_data *pmic_data) +{ + /* Phoenix Audio IC needs I2C1 to start with 400 KHz or less */ + omap_pmic_init(1, 400, pmic_type, OMAP44XX_IRQ_SYS_1N, pmic_data); +} + +#endif /* __OMAP_PMIC_COMMON__ */
Reduce the amount of duplicated code by moving the common configuration for TWL6030 (on OMAP4 platform) to the twl-common file. Use the omap4_pmic_get_config function from board files to properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/board-4430sdp.c | 143 ++-------------------------- arch/arm/mach-omap2/board-omap4panda.c | 149 +++--------------------------- arch/arm/mach-omap2/twl-common.c | 163 ++++++++++++++++++++++++++++++++ arch/arm/mach-omap2/twl-common.h | 20 ++++ 4 files changed, 205 insertions(+), 270 deletions(-)
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index 63de2d3..968029a 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -306,14 +306,6 @@ static struct omap_musb_board_data musb_board_data = { .power = 100, };
-static struct twl4030_usb_data omap4_usbphy_data = { - .phy_init = omap4430_phy_init, - .phy_exit = omap4430_phy_exit, - .phy_power = omap4430_phy_power, - .phy_set_clock = omap4430_phy_set_clk, - .phy_suspend = omap4430_phy_suspend, -}; - static struct omap2_hsmmc_info mmc[] = { { .mmc = 2, @@ -338,12 +330,6 @@ static struct regulator_consumer_supply sdp4430_vaux_supply[] = { .dev_name = "omap_hsmmc.1", }, }; -static struct regulator_consumer_supply sdp4430_vmmc_supply[] = { - { - .supply = "vmmc", - .dev_name = "omap_hsmmc.0", - }, -};
static int omap4_twl6030_hsmmc_late_init(struct device *dev) { @@ -403,61 +389,6 @@ static struct regulator_init_data sdp4430_vaux1 = { .consumer_supplies = sdp4430_vaux_supply, };
-static struct regulator_init_data sdp4430_vaux2 = { - .constraints = { - .min_uV = 1200000, - .max_uV = 2800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data sdp4430_vaux3 = { - .constraints = { - .min_uV = 1000000, - .max_uV = 3000000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -/* VMMC1 for MMC1 card */ -static struct regulator_init_data sdp4430_vmmc = { - .constraints = { - .min_uV = 1200000, - .max_uV = 3000000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = sdp4430_vmmc_supply, -}; - -static struct regulator_init_data sdp4430_vpp = { - .constraints = { - .min_uV = 1800000, - .max_uV = 2500000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - static struct regulator_init_data sdp4430_vusim = { .constraints = { .min_uV = 1200000, @@ -471,74 +402,10 @@ static struct regulator_init_data sdp4430_vusim = { }, };
-static struct regulator_init_data sdp4430_vana = { - .constraints = { - .min_uV = 2100000, - .max_uV = 2100000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data sdp4430_vcxio = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data sdp4430_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data sdp4430_vusb = { - .constraints = { - .min_uV = 3300000, - .max_uV = 3300000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data sdp4430_clk32kg = { - .constraints = { - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, -}; - static struct twl4030_platform_data sdp4430_twldata = { - .irq_base = TWL6030_IRQ_BASE, - .irq_end = TWL6030_IRQ_END, - /* Regulators */ - .vmmc = &sdp4430_vmmc, - .vpp = &sdp4430_vpp, .vusim = &sdp4430_vusim, - .vana = &sdp4430_vana, - .vcxio = &sdp4430_vcxio, - .vdac = &sdp4430_vdac, - .vusb = &sdp4430_vusb, .vaux1 = &sdp4430_vaux1, - .vaux2 = &sdp4430_vaux2, - .vaux3 = &sdp4430_vaux3, - .clk32kg = &sdp4430_clk32kg, - .usb = &omap4_usbphy_data };
static struct i2c_board_info __initdata sdp4430_i2c_3_boardinfo[] = { @@ -556,6 +423,16 @@ static struct i2c_board_info __initdata sdp4430_i2c_4_boardinfo[] = { }; static int __init omap4_i2c_init(void) { + omap4_pmic_get_config(&sdp4430_twldata, TWL_COMMON_PDATA_USB, + TWL_COMMON_REGULATOR_VDAC | + TWL_COMMON_REGULATOR_VAUX2 | + TWL_COMMON_REGULATOR_VAUX3 | + TWL_COMMON_REGULATOR_VMMC | + TWL_COMMON_REGULATOR_VPP | + TWL_COMMON_REGULATOR_VANA | + TWL_COMMON_REGULATOR_VCXIO | + TWL_COMMON_REGULATOR_VUSB | + TWL_COMMON_REGULATOR_CLK32KG); omap4_pmic_init("twl6030", &sdp4430_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, sdp4430_i2c_3_boardinfo, diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c index 0cfe200..f988a1d 100644 --- a/arch/arm/mach-omap2/board-omap4panda.c +++ b/arch/arm/mach-omap2/board-omap4panda.c @@ -155,14 +155,6 @@ static struct omap_musb_board_data musb_board_data = { .power = 100, };
-static struct twl4030_usb_data omap4_usbphy_data = { - .phy_init = omap4430_phy_init, - .phy_exit = omap4430_phy_exit, - .phy_power = omap4430_phy_power, - .phy_set_clock = omap4430_phy_set_clk, - .phy_suspend = omap4430_phy_suspend, -}; - static struct omap2_hsmmc_info mmc[] = { { .mmc = 1, @@ -182,13 +174,6 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ };
-static struct regulator_consumer_supply omap4_panda_vmmc_supply[] = { - { - .supply = "vmmc", - .dev_name = "omap_hsmmc.0", - }, -}; - static struct regulator_consumer_supply omap4_panda_vmmc5_supply = { .supply = "vmmc", .dev_name = "omap_hsmmc.4", @@ -274,128 +259,8 @@ static int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers) return 0; }
-static struct regulator_init_data omap4_panda_vaux2 = { - .constraints = { - .min_uV = 1200000, - .max_uV = 2800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data omap4_panda_vaux3 = { - .constraints = { - .min_uV = 1000000, - .max_uV = 3000000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -/* VMMC1 for MMC1 card */ -static struct regulator_init_data omap4_panda_vmmc = { - .constraints = { - .min_uV = 1200000, - .max_uV = 3000000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = omap4_panda_vmmc_supply, -}; - -static struct regulator_init_data omap4_panda_vpp = { - .constraints = { - .min_uV = 1800000, - .max_uV = 2500000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE - | REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data omap4_panda_vana = { - .constraints = { - .min_uV = 2100000, - .max_uV = 2100000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data omap4_panda_vcxio = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data omap4_panda_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data omap4_panda_vusb = { - .constraints = { - .min_uV = 3300000, - .max_uV = 3300000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, -}; - -static struct regulator_init_data omap4_panda_clk32kg = { - .constraints = { - .valid_ops_mask = REGULATOR_CHANGE_STATUS, - }, -}; - -static struct twl4030_platform_data omap4_panda_twldata = { - .irq_base = TWL6030_IRQ_BASE, - .irq_end = TWL6030_IRQ_END, - - /* Regulators */ - .vmmc = &omap4_panda_vmmc, - .vpp = &omap4_panda_vpp, - .vana = &omap4_panda_vana, - .vcxio = &omap4_panda_vcxio, - .vdac = &omap4_panda_vdac, - .vusb = &omap4_panda_vusb, - .vaux2 = &omap4_panda_vaux2, - .vaux3 = &omap4_panda_vaux3, - .clk32kg = &omap4_panda_clk32kg, - .usb = &omap4_usbphy_data, -}; +/* Use the common PMIC configuration for Panda */ +static struct twl4030_platform_data omap4_panda_twldata;
/* * Display monitor features are burnt in their EEPROM as EDID data. The EEPROM @@ -409,6 +274,16 @@ static struct i2c_board_info __initdata panda_i2c_eeprom[] = {
static int __init omap4_panda_i2c_init(void) { + omap4_pmic_get_config(&omap4_panda_twldata, TWL_COMMON_PDATA_USB, + TWL_COMMON_REGULATOR_VDAC | + TWL_COMMON_REGULATOR_VAUX2 | + TWL_COMMON_REGULATOR_VAUX3 | + TWL_COMMON_REGULATOR_VMMC | + TWL_COMMON_REGULATOR_VPP | + TWL_COMMON_REGULATOR_VANA | + TWL_COMMON_REGULATOR_VCXIO | + TWL_COMMON_REGULATOR_VUSB | + TWL_COMMON_REGULATOR_CLK32KG); omap4_pmic_init("twl6030", &omap4_panda_twldata); omap_register_i2c_bus(2, 400, NULL, 0); /* diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 4f7b24c..5fd644e 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -23,8 +23,11 @@ #include <linux/i2c.h> #include <linux/i2c/twl.h> #include <linux/gpio.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h>
#include <plat/i2c.h> +#include <plat/usb.h>
#include "twl-common.h"
@@ -44,3 +47,163 @@ void __init omap_pmic_init(int bus, u32 clkrate,
omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1); } + +static struct twl4030_usb_data omap4_usb_pdata = { + .phy_init = omap4430_phy_init, + .phy_exit = omap4430_phy_exit, + .phy_power = omap4430_phy_power, + .phy_set_clock = omap4430_phy_set_clk, + .phy_suspend = omap4430_phy_suspend, +}; + +static struct regulator_init_data omap4_vdac_idata = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_init_data omap4_vaux2_idata = { + .constraints = { + .min_uV = 1200000, + .max_uV = 2800000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_init_data omap4_vaux3_idata = { + .constraints = { + .min_uV = 1000000, + .max_uV = 3000000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_consumer_supply omap4_vmmc_supply[] = { + REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), +}; + +/* VMMC1 for MMC1 card */ +static struct regulator_init_data omap4_vmmc_idata = { + .constraints = { + .min_uV = 1200000, + .max_uV = 3000000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(omap4_vmmc_supply), + .consumer_supplies = omap4_vmmc_supply, +}; + +static struct regulator_init_data omap4_vpp_idata = { + .constraints = { + .min_uV = 1800000, + .max_uV = 2500000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE + | REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_init_data omap4_vana_idata = { + .constraints = { + .min_uV = 2100000, + .max_uV = 2100000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_init_data omap4_vcxio_idata = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_init_data omap4_vusb_idata = { + .constraints = { + .min_uV = 3300000, + .max_uV = 3300000, + .apply_uV = true, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, +}; + +static struct regulator_init_data omap4_clk32kg_idata = { + .constraints = { + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, +}; + +void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data, + u32 pdata_flags, u32 regulators_flags) +{ + if (!pmic_data->irq_base) + pmic_data->irq_base = TWL6030_IRQ_BASE; + if (!pmic_data->irq_end) + pmic_data->irq_end = TWL6030_IRQ_END; + + /* Common platform data configurations */ + if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb) + pmic_data->usb = &omap4_usb_pdata; + + /* Common regulator configurations */ + if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac) + pmic_data->vdac = &omap4_vdac_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VAUX2 && !pmic_data->vaux2) + pmic_data->vaux2 = &omap4_vaux2_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VAUX3 && !pmic_data->vaux3) + pmic_data->vaux3 = &omap4_vaux3_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VMMC && !pmic_data->vmmc) + pmic_data->vmmc = &omap4_vmmc_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VPP && !pmic_data->vpp) + pmic_data->vpp = &omap4_vpp_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VANA && !pmic_data->vana) + pmic_data->vana = &omap4_vana_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VCXIO && !pmic_data->vcxio) + pmic_data->vcxio = &omap4_vcxio_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VUSB && !pmic_data->vusb) + pmic_data->vusb = &omap4_vusb_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_CLK32KG && + !pmic_data->clk32kg) + pmic_data->clk32kg = &omap4_clk32kg_idata; +} diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h index e9fe2ab..d96c289 100644 --- a/arch/arm/mach-omap2/twl-common.h +++ b/arch/arm/mach-omap2/twl-common.h @@ -1,6 +1,23 @@ #ifndef __OMAP_PMIC_COMMON__ #define __OMAP_PMIC_COMMON__
+#define TWL_COMMON_PDATA_USB (1 << 0) + +/* Common LDO regulators for TWL4030/TWL6030 */ +#define TWL_COMMON_REGULATOR_VDAC (1 << 0) +#define TWL_COMMON_REGULATOR_VAUX1 (1 << 1) +#define TWL_COMMON_REGULATOR_VAUX2 (1 << 2) +#define TWL_COMMON_REGULATOR_VAUX3 (1 << 3) + +/* TWL6030 LDO regulators */ +#define TWL_COMMON_REGULATOR_VMMC (1 << 4) +#define TWL_COMMON_REGULATOR_VPP (1 << 5) +#define TWL_COMMON_REGULATOR_VUSIM (1 << 6) +#define TWL_COMMON_REGULATOR_VANA (1 << 7) +#define TWL_COMMON_REGULATOR_VCXIO (1 << 8) +#define TWL_COMMON_REGULATOR_VUSB (1 << 9) +#define TWL_COMMON_REGULATOR_CLK32KG (1 << 10) + struct twl4030_platform_data;
void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq, @@ -25,4 +42,7 @@ static inline void omap4_pmic_init(const char *pmic_type, omap_pmic_init(1, 400, pmic_type, OMAP44XX_IRQ_SYS_1N, pmic_data); }
+void omap4_pmic_get_config(struct twl4030_platform_data *pmic_data, + u32 pdata_flags, u32 regulators_flags); + #endif /* __OMAP_PMIC_COMMON__ */
Reduce the amount of duplicated code by moving the common configuration for twl4030/5030/tpsxx to the twl-common file. Use the omap3_pmic_get_config function from board files to properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/board-3430sdp.c | 42 ++------------------ arch/arm/mach-omap2/board-cm-t35.c | 9 +---- arch/arm/mach-omap2/board-devkit8000.c | 18 +-------- arch/arm/mach-omap2/board-igep0020.c | 20 ++-------- arch/arm/mach-omap2/board-ldp.c | 15 +------ arch/arm/mach-omap2/board-omap3beagle.c | 18 +-------- arch/arm/mach-omap2/board-omap3evm.c | 24 +---------- arch/arm/mach-omap2/board-omap3pandora.c | 17 +------- arch/arm/mach-omap2/board-omap3stalker.c | 24 +---------- arch/arm/mach-omap2/board-omap3touchbook.c | 19 +-------- arch/arm/mach-omap2/board-overo.c | 17 +------- arch/arm/mach-omap2/board-rm680.c | 8 +--- arch/arm/mach-omap2/board-rx51-peripherals.c | 15 +------ arch/arm/mach-omap2/board-zoom-peripherals.c | 51 +++++-------------------- arch/arm/mach-omap2/twl-common.c | 53 ++++++++++++++++++++++++++ arch/arm/mach-omap2/twl-common.h | 6 +++ 16 files changed, 99 insertions(+), 257 deletions(-)
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 5dac974..4810dcc 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -231,22 +231,6 @@ static void __init omap_3430sdp_init_early(void) omap2_init_common_devices(hyb18m512160af6_sdrc_params, NULL); }
-static int sdp3430_batt_table[] = { -/* 0 C*/ -30800, 29500, 28300, 27100, -26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, -17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, -11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, -8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, -5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, -4040, 3910, 3790, 3670, 3550 -}; - -static struct twl4030_bci_platform_data sdp3430_bci_data = { - .battery_tmp_tbl = sdp3430_batt_table, - .tblsize = ARRAY_SIZE(sdp3430_batt_table), -}; - static struct omap2_hsmmc_info mmc[] = { { .mmc = 1, @@ -292,14 +276,6 @@ static struct twl4030_gpio_platform_data sdp3430_gpio_data = { .setup = sdp3430_twl_gpio_setup, };
-static struct twl4030_usb_data sdp3430_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static struct twl4030_madc_platform_data sdp3430_madc_data = { - .irq_line = 1, -}; - /* regulator consumer mappings */
/* ads7846 on SPI */ @@ -463,24 +439,10 @@ static struct regulator_init_data sdp3430_vpll2 = { .consumer_supplies = sdp3430_vpll2_supplies, };
-static struct twl4030_codec_audio_data sdp3430_audio; - -static struct twl4030_codec_data sdp3430_codec = { - .audio_mclk = 26000000, - .audio = &sdp3430_audio, -}; - static struct twl4030_platform_data sdp3430_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .bci = &sdp3430_bci_data, .gpio = &sdp3430_gpio_data, - .madc = &sdp3430_madc_data, .keypad = &sdp3430_kp_data, - .usb = &sdp3430_usb_data, - .codec = &sdp3430_codec,
.vaux1 = &sdp3430_vaux1, .vaux2 = &sdp3430_vaux2, @@ -496,7 +458,11 @@ static struct twl4030_platform_data sdp3430_twldata = { static int __init omap3430_i2c_init(void) { /* i2c1 for PMIC only */ + omap3_pmic_get_config(&sdp3430_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | + TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("twl4030", &sdp3430_twldata); + /* i2c2 on camera connector (for sensor control) and optional isp1301 */ omap_register_i2c_bus(2, 400, NULL, 0); /* i2c3 on display connector (for DVI, tfp410) */ diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c index 77456de..e867474 100644 --- a/arch/arm/mach-omap2/board-cm-t35.c +++ b/arch/arm/mach-omap2/board-cm-t35.c @@ -410,10 +410,6 @@ static struct regulator_init_data cm_t35_vpll2 = { .consumer_supplies = &cm_t35_vdvi_supply, };
-static struct twl4030_usb_data cm_t35_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static uint32_t cm_t35_keymap[] = { KEY(0, 0, KEY_A), KEY(0, 1, KEY_B), KEY(0, 2, KEY_LEFT), KEY(1, 0, KEY_UP), KEY(1, 1, KEY_ENTER), KEY(1, 2, KEY_DOWN), @@ -496,12 +492,8 @@ static struct twl4030_gpio_platform_data cm_t35_gpio_data = { };
static struct twl4030_platform_data cm_t35_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ .keypad = &cm_t35_kp_data, - .usb = &cm_t35_usb_data, .gpio = &cm_t35_gpio_data, .vmmc1 = &cm_t35_vmmc1, .vsim = &cm_t35_vsim, @@ -511,6 +503,7 @@ static struct twl4030_platform_data cm_t35_twldata = {
static void __init cm_t35_init_i2c(void) { + omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB, 0); omap3_pmic_init("tps65930", &cm_t35_twldata); }
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index 34956ec..aa6a173 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -331,25 +331,9 @@ static struct regulator_init_data devkit8000_vio = { .consumer_supplies = &devkit8000_vio_supply, };
-static struct twl4030_usb_data devkit8000_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static struct twl4030_codec_audio_data devkit8000_audio_data; - -static struct twl4030_codec_data devkit8000_codec_data = { - .audio_mclk = 26000000, - .audio = &devkit8000_audio_data, -}; - static struct twl4030_platform_data devkit8000_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .usb = &devkit8000_usb_data, .gpio = &devkit8000_gpio_data, - .codec = &devkit8000_codec_data, .vmmc1 = &devkit8000_vmmc1, .vdac = &devkit8000_vdac, .vpll1 = &devkit8000_vpll1, @@ -359,6 +343,8 @@ static struct twl4030_platform_data devkit8000_twldata = {
static int __init devkit8000_i2c_init(void) { + omap3_pmic_get_config(&devkit8000_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("tps65930", &devkit8000_twldata); /* Bus 3 is attached to the DVI port where devices like the pico DLP * projector don't work reliably with 400kHz */ diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c index 0c1bfca..bb3723a 100644 --- a/arch/arm/mach-omap2/board-igep0020.c +++ b/arch/arm/mach-omap2/board-igep0020.c @@ -440,10 +440,6 @@ static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = { .setup = igep_twl_gpio_setup, };
-static struct twl4030_usb_data igep_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static int igep2_enable_dvi(struct omap_dss_device *dssdev) { gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1); @@ -519,13 +515,6 @@ static void __init igep_init_early(void) m65kxxxxam_sdrc_params); }
-static struct twl4030_codec_audio_data igep2_audio_data; - -static struct twl4030_codec_data igep2_codec_data = { - .audio_mclk = 26000000, - .audio = &igep2_audio_data, -}; - static int igep2_keymap[] = { KEY(0, 0, KEY_LEFT), KEY(0, 1, KEY_RIGHT), @@ -558,11 +547,7 @@ static struct twl4030_keypad_data igep2_keypad_pdata = { };
static struct twl4030_platform_data igep_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .usb = &igep_usb_data, .gpio = &igep_twl4030_gpio_pdata, .vmmc1 = &igep_vmmc1, .vio = &igep_vio, @@ -578,6 +563,8 @@ static void __init igep_i2c_init(void) { int ret;
+ omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_USB, 0); + if (machine_is_igep0020()) { /* * Bus 3 is attached to the DVI port where devices like the @@ -588,9 +575,10 @@ static void __init igep_i2c_init(void) if (ret) pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
- igep_twldata.codec = &igep2_codec_data; igep_twldata.keypad = &igep2_keypad_pdata; igep_twldata.vpll2 = &igep2_vpll2; + /* Use common codec data */ + omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, 0); }
omap3_pmic_init("twl4030", &igep_twldata); diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index f7d6038..6ff564a 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -199,20 +199,12 @@ static void __init omap_ldp_init_early(void) omap2_init_common_devices(NULL, NULL); }
-static struct twl4030_usb_data ldp_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static struct twl4030_gpio_platform_data ldp_gpio_data = { .gpio_base = OMAP_MAX_GPIO_LINES, .irq_base = TWL4030_GPIO_IRQ_BASE, .irq_end = TWL4030_GPIO_IRQ_END, };
-static struct twl4030_madc_platform_data ldp_madc_data = { - .irq_line = 1, -}; - static struct regulator_consumer_supply ldp_vmmc1_supply = { .supply = "vmmc", }; @@ -253,12 +245,7 @@ static struct regulator_init_data ldp_vaux1 = { };
static struct twl4030_platform_data ldp_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .madc = &ldp_madc_data, - .usb = &ldp_usb_data, .vmmc1 = &ldp_vmmc1, .vaux1 = &ldp_vaux1, .gpio = &ldp_gpio_data, @@ -267,6 +254,8 @@ static struct twl4030_platform_data ldp_twldata = {
static int __init omap_i2c_init(void) { + omap3_pmic_get_config(&ldp_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC, 0); omap3_pmic_init("twl4030", &ldp_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 7f21d24..63104e8 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -384,25 +384,9 @@ static struct regulator_init_data beagle_vpll2 = { .consumer_supplies = beagle_vdvi_supplies, };
-static struct twl4030_usb_data beagle_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static struct twl4030_codec_audio_data beagle_audio_data; - -static struct twl4030_codec_data beagle_codec_data = { - .audio_mclk = 26000000, - .audio = &beagle_audio_data, -}; - static struct twl4030_platform_data beagle_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .usb = &beagle_usb_data, .gpio = &beagle_gpio_data, - .codec = &beagle_codec_data, .vmmc1 = &beagle_vmmc1, .vsim = &beagle_vsim, .vdac = &beagle_vdac, @@ -417,6 +401,8 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
static int __init omap3_beagle_i2c_init(void) { + omap3_pmic_get_config(&beagle_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("twl4030", &beagle_twldata); /* Bus 3 is attached to the DVI port where devices like the pico DLP * projector don't work reliably with 400kHz */ diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index b4d4346..3e7e902 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -400,10 +400,6 @@ static struct twl4030_gpio_platform_data omap3evm_gpio_data = { .setup = omap3evm_twl_gpio_setup, };
-static struct twl4030_usb_data omap3evm_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static uint32_t board_keymap[] = { KEY(0, 0, KEY_LEFT), KEY(0, 1, KEY_DOWN), @@ -438,17 +434,6 @@ static struct twl4030_keypad_data omap3evm_kp_data = { .rep = 1, };
-static struct twl4030_madc_platform_data omap3evm_madc_data = { - .irq_line = 1, -}; - -static struct twl4030_codec_audio_data omap3evm_audio_data; - -static struct twl4030_codec_data omap3evm_codec_data = { - .audio_mclk = 26000000, - .audio = &omap3evm_audio_data, -}; - static struct regulator_consumer_supply omap3_evm_vdda_dac_supply = REGULATOR_SUPPLY("vdda_dac", "omapdss_venc");
@@ -548,15 +533,9 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = { #endif
static struct twl4030_platform_data omap3evm_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ .keypad = &omap3evm_kp_data, - .madc = &omap3evm_madc_data, - .usb = &omap3evm_usb_data, .gpio = &omap3evm_gpio_data, - .codec = &omap3evm_codec_data, .vdac = &omap3_evm_vdac, .vpll2 = &omap3_evm_vpll2, .vio = &omap3evm_vio, @@ -566,6 +545,9 @@ static struct twl4030_platform_data omap3evm_twldata = {
static int __init omap3_evm_i2c_init(void) { + omap3_pmic_get_config(&omap3evm_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | + TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("twl4030", &omap3evm_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 23f71d4..7bfe109 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -501,25 +501,10 @@ static struct platform_device pandora_vwlan_device = { }, };
-static struct twl4030_usb_data omap3pandora_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static struct twl4030_codec_audio_data omap3pandora_audio_data; - -static struct twl4030_codec_data omap3pandora_codec_data = { - .audio_mclk = 26000000, - .audio = &omap3pandora_audio_data, -}; - static struct twl4030_bci_platform_data pandora_bci_data;
static struct twl4030_platform_data omap3pandora_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, .gpio = &omap3pandora_gpio_data, - .usb = &omap3pandora_usb_data, - .codec = &omap3pandora_codec_data, .vmmc1 = &pandora_vmmc1, .vmmc2 = &pandora_vmmc2, .vdac = &pandora_vdac, @@ -541,6 +526,8 @@ static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = {
static int __init omap3pandora_i2c_init(void) { + omap3_pmic_get_config(&omap3pandora_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("tps65950", &omap3pandora_twldata); /* i2c2 pins are not connected */ omap_register_i2c_bus(3, 100, omap3pandora_i2c3_boardinfo, diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c index 0c108a2..2b52281 100644 --- a/arch/arm/mach-omap2/board-omap3stalker.c +++ b/arch/arm/mach-omap2/board-omap3stalker.c @@ -354,10 +354,6 @@ static struct twl4030_gpio_platform_data omap3stalker_gpio_data = { .setup = omap3stalker_twl_gpio_setup, };
-static struct twl4030_usb_data omap3stalker_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static uint32_t board_keymap[] = { KEY(0, 0, KEY_LEFT), KEY(0, 1, KEY_DOWN), @@ -392,17 +388,6 @@ static struct twl4030_keypad_data omap3stalker_kp_data = { .rep = 1, };
-static struct twl4030_madc_platform_data omap3stalker_madc_data = { - .irq_line = 1, -}; - -static struct twl4030_codec_audio_data omap3stalker_audio_data; - -static struct twl4030_codec_data omap3stalker_codec_data = { - .audio_mclk = 26000000, - .audio = &omap3stalker_audio_data, -}; - static struct regulator_consumer_supply omap3_stalker_vdda_dac_supply = REGULATOR_SUPPLY("vdda_dac", "omapdss_venc");
@@ -443,15 +428,9 @@ static struct regulator_init_data omap3_stalker_vpll2 = { };
static struct twl4030_platform_data omap3stalker_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ .keypad = &omap3stalker_kp_data, - .madc = &omap3stalker_madc_data, - .usb = &omap3stalker_usb_data, .gpio = &omap3stalker_gpio_data, - .codec = &omap3stalker_codec_data, .vdac = &omap3_stalker_vdac, .vpll2 = &omap3_stalker_vpll2, .vmmc1 = &omap3stalker_vmmc1, @@ -474,6 +453,9 @@ static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
static int __init omap3_stalker_i2c_init(void) { + omap3_pmic_get_config(&omap3stalker_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | + TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("twl4030", &omap3stalker_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3, diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c index 5f649fa..094ea80 100644 --- a/arch/arm/mach-omap2/board-omap3touchbook.c +++ b/arch/arm/mach-omap2/board-omap3touchbook.c @@ -236,25 +236,9 @@ static struct regulator_init_data touchbook_vpll2 = { .consumer_supplies = &touchbook_vdvi_supply, };
-static struct twl4030_usb_data touchbook_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - -static struct twl4030_codec_audio_data touchbook_audio_data; - -static struct twl4030_codec_data touchbook_codec_data = { - .audio_mclk = 26000000, - .audio = &touchbook_audio_data, -}; - static struct twl4030_platform_data touchbook_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .usb = &touchbook_usb_data, .gpio = &touchbook_gpio_data, - .codec = &touchbook_codec_data, .vmmc1 = &touchbook_vmmc1, .vsim = &touchbook_vsim, .vdac = &touchbook_vdac, @@ -270,8 +254,9 @@ static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = { static int __init omap3_touchbook_i2c_init(void) { /* Standard TouchBook bus */ + omap3_pmic_get_config(&touchbook_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("twl4030", &touchbook_twldata); - /* Additional TouchBook bus */ omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo, ARRAY_SIZE(touchBook_i2c_boardinfo)); diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 175e1ab..f334829 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -433,10 +433,6 @@ static struct twl4030_gpio_platform_data overo_gpio_data = { .setup = overo_twl_gpio_setup, };
-static struct twl4030_usb_data overo_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static struct regulator_init_data overo_vmmc1 = { .constraints = { .min_uV = 1850000, @@ -480,19 +476,8 @@ static struct regulator_init_data overo_vpll2 = { .consumer_supplies = overo_vdds_dsi_supply, };
-static struct twl4030_codec_audio_data overo_audio_data; - -static struct twl4030_codec_data overo_codec_data = { - .audio_mclk = 26000000, - .audio = &overo_audio_data, -}; - static struct twl4030_platform_data overo_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, .gpio = &overo_gpio_data, - .usb = &overo_usb_data, - .codec = &overo_codec_data, .vmmc1 = &overo_vmmc1, .vdac = &overo_vdac, .vpll2 = &overo_vpll2, @@ -500,6 +485,8 @@ static struct twl4030_platform_data overo_twldata = {
static int __init overo_i2c_init(void) { + omap3_pmic_get_config(&overo_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); omap3_pmic_init("tps65950", &overo_twldata); /* i2c2 pins are used for gpio */ omap_register_i2c_bus(3, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/board-rm680.c b/arch/arm/mach-omap2/board-rm680.c index 42d10b1..62d6675 100644 --- a/arch/arm/mach-omap2/board-rm680.c +++ b/arch/arm/mach-omap2/board-rm680.c @@ -79,20 +79,14 @@ static struct twl4030_gpio_platform_data rm680_gpio_data = { .pulldowns = BIT(1) | BIT(2) | BIT(8) | BIT(15), };
-static struct twl4030_usb_data rm680_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static struct twl4030_platform_data rm680_twl_data = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, .gpio = &rm680_gpio_data, - .usb = &rm680_usb_data, /* add rest of the children here */ };
static void __init rm680_i2c_init(void) { + omap3_pmic_get_config(&rm680_twl_data, TWL_COMMON_PDATA_USB, 0); omap_pmic_init(1, 2900, "twl5031", INT_34XX_SYS_NIRQ, &rm680_twl_data); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index 9903667..dc69a7f 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -288,10 +288,6 @@ static struct twl4030_keypad_data rx51_kp_data = { .rep = 1, };
-static struct twl4030_madc_platform_data rx51_madc_data = { - .irq_line = 1, -}; - /* Enable input logic and pull all lines up when eMMC is on. */ static struct omap_board_mux rx51_mmc2_on_mux[] = { OMAP3_MUX(SDMMC2_CMD, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0), @@ -600,10 +596,6 @@ static struct twl4030_gpio_platform_data rx51_gpio_data = { .setup = rx51_twlgpio_setup, };
-static struct twl4030_usb_data rx51_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static struct twl4030_ins sleep_on_seq[] __initdata = { /* * Turn off everything @@ -775,14 +767,9 @@ struct twl4030_codec_data rx51_codec_data __initdata = { };
static struct twl4030_platform_data rx51_twldata __initdata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ .gpio = &rx51_gpio_data, .keypad = &rx51_kp_data, - .madc = &rx51_madc_data, - .usb = &rx51_usb_data, .power = &rx51_t2scripts_data, .codec = &rx51_codec_data,
@@ -847,6 +834,8 @@ static int __init rx51_i2c_init(void) rx51_twldata.vaux3 = &rx51_vaux3_cam; } rx51_twldata.vmmc2 = &rx51_vmmc2; + omap3_pmic_get_config(&rx51_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC, 0); omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata); omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2, ARRAY_SIZE(rx51_peripherals_i2c_board_info_2)); diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c index 118c6f5..58c0c6e 100644 --- a/arch/arm/mach-omap2/board-zoom-peripherals.c +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -292,26 +292,6 @@ static void zoom2_set_hs_extmute(int mute) gpio_set_value(ZOOM2_HEADSET_EXTMUTE_GPIO, mute); }
-static int zoom_batt_table[] = { -/* 0 C*/ -30800, 29500, 28300, 27100, -26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, -17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, -11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, -8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, -5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, -4040, 3910, 3790, 3670, 3550 -}; - -static struct twl4030_bci_platform_data zoom_bci_data = { - .battery_tmp_tbl = zoom_batt_table, - .tblsize = ARRAY_SIZE(zoom_batt_table), -}; - -static struct twl4030_usb_data zoom_usb_data = { - .usb_mode = T2_USB_MODE_ULPI, -}; - static struct twl4030_gpio_platform_data zoom_gpio_data = { .gpio_base = OMAP_MAX_GPIO_LINES, .irq_base = TWL4030_GPIO_IRQ_BASE, @@ -319,28 +299,10 @@ static struct twl4030_gpio_platform_data zoom_gpio_data = { .setup = zoom_twl_gpio_setup, };
-static struct twl4030_madc_platform_data zoom_madc_data = { - .irq_line = 1, -}; - -static struct twl4030_codec_audio_data zoom_audio_data; - -static struct twl4030_codec_data zoom_codec_data = { - .audio_mclk = 26000000, - .audio = &zoom_audio_data, -}; - static struct twl4030_platform_data zoom_twldata = { - .irq_base = TWL4030_IRQ_BASE, - .irq_end = TWL4030_IRQ_END, - /* platform_data for children goes here */ - .bci = &zoom_bci_data, - .madc = &zoom_madc_data, - .usb = &zoom_usb_data, .gpio = &zoom_gpio_data, .keypad = &zoom_kp_twl4030_data, - .codec = &zoom_codec_data, .vmmc1 = &zoom_vmmc1, .vmmc2 = &zoom_vmmc2, .vsim = &zoom_vsim, @@ -350,10 +312,17 @@ static struct twl4030_platform_data zoom_twldata = {
static int __init omap_i2c_init(void) { + omap3_pmic_get_config(&zoom_twldata, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | + TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, 0); + if (machine_is_omap_zoom2()) { - zoom_audio_data.ramp_delay_value = 3; /* 161 ms */ - zoom_audio_data.hs_extmute = 1; - zoom_audio_data.set_hs_extmute = zoom2_set_hs_extmute; + struct twl4030_codec_audio_data *audio_data; + audio_data = zoom_twldata.codec->audio; + + audio_data->ramp_delay_value = 3; /* 161 ms */ + audio_data->hs_extmute = 1; + audio_data->set_hs_extmute = zoom2_set_hs_extmute; } omap_pmic_init(1, 2400, "twl5030", INT_34XX_SYS_NIRQ, &zoom_twldata); omap_register_i2c_bus(2, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 5fd644e..2487e3c 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -56,6 +56,37 @@ static struct twl4030_usb_data omap4_usb_pdata = { .phy_suspend = omap4430_phy_suspend, };
+static struct twl4030_usb_data omap3_usb_pdata = { + .usb_mode = T2_USB_MODE_ULPI, +}; + +static int omap3_batt_table[] = { +/* 0 C */ +30800, 29500, 28300, 27100, +26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900, +17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100, +11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310, +8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830, +5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170, +4040, 3910, 3790, 3670, 3550 +}; + +static struct twl4030_bci_platform_data omap3_bci_pdata = { + .battery_tmp_tbl = omap3_batt_table, + .tblsize = ARRAY_SIZE(omap3_batt_table), +}; + +static struct twl4030_madc_platform_data omap3_madc_pdata = { + .irq_line = 1, +}; + +static struct twl4030_codec_audio_data omap3_audio; + +static struct twl4030_codec_data omap3_codec_pdata = { + .audio_mclk = 26000000, + .audio = &omap3_audio, +}; + static struct regulator_init_data omap4_vdac_idata = { .constraints = { .min_uV = 1800000, @@ -207,3 +238,25 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data, !pmic_data->clk32kg) pmic_data->clk32kg = &omap4_clk32kg_idata; } + +void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data, + u32 pdata_flags, u32 regulators_flags) +{ + if (!pmic_data->irq_base) + pmic_data->irq_base = TWL4030_IRQ_BASE; + if (!pmic_data->irq_end) + pmic_data->irq_end = TWL4030_IRQ_END; + + /* Common platform data configurations */ + if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb) + pmic_data->usb = &omap3_usb_pdata; + + if (pdata_flags & TWL_COMMON_PDATA_BCI && !pmic_data->bci) + pmic_data->bci = &omap3_bci_pdata; + + if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc) + pmic_data->madc = &omap3_madc_pdata; + + if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->codec) + pmic_data->codec = &omap3_codec_pdata; +} diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h index d96c289..3b4b05d 100644 --- a/arch/arm/mach-omap2/twl-common.h +++ b/arch/arm/mach-omap2/twl-common.h @@ -2,6 +2,9 @@ #define __OMAP_PMIC_COMMON__
#define TWL_COMMON_PDATA_USB (1 << 0) +#define TWL_COMMON_PDATA_BCI (1 << 1) +#define TWL_COMMON_PDATA_MADC (1 << 2) +#define TWL_COMMON_PDATA_AUDIO (1 << 3)
/* Common LDO regulators for TWL4030/TWL6030 */ #define TWL_COMMON_REGULATOR_VDAC (1 << 0) @@ -42,6 +45,9 @@ static inline void omap4_pmic_init(const char *pmic_type, omap_pmic_init(1, 400, pmic_type, OMAP44XX_IRQ_SYS_1N, pmic_data); }
+void omap3_pmic_get_config(struct twl4030_platform_data *pmic_data, + u32 pdata_flags, u32 regulators_flags); + void omap4_pmic_get_config(struct twl4030_platform_data *pmic_data, u32 pdata_flags, u32 regulators_flags);
Some regulator config can be moved out from board files, since they are close to identical.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/board-3430sdp.c | 51 ++++---------------------- arch/arm/mach-omap2/board-cm-t35.c | 41 +++------------------ arch/arm/mach-omap2/board-devkit8000.c | 21 +---------- arch/arm/mach-omap2/board-igep0020.c | 28 +++------------ arch/arm/mach-omap2/board-omap3beagle.c | 44 ++-------------------- arch/arm/mach-omap2/board-omap3evm.c | 47 +++--------------------- arch/arm/mach-omap2/board-omap3pandora.c | 44 ++++------------------ arch/arm/mach-omap2/board-omap3stalker.c | 48 +++--------------------- arch/arm/mach-omap2/board-omap3touchbook.c | 40 ++++---------------- arch/arm/mach-omap2/board-overo.c | 44 ++-------------------- arch/arm/mach-omap2/board-rx51-peripherals.c | 25 ++----------- arch/arm/mach-omap2/board-zoom-peripherals.c | 41 ++------------------- arch/arm/mach-omap2/twl-common.c | 42 +++++++++++++++++++++ arch/arm/mach-omap2/twl-common.h | 5 +++ 14 files changed, 109 insertions(+), 412 deletions(-)
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 4810dcc..d944a56 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -283,16 +283,6 @@ static struct regulator_consumer_supply sdp3430_vaux3_supplies[] = { REGULATOR_SUPPLY("vcc", "spi1.0"), };
-static struct regulator_consumer_supply sdp3430_vdda_dac_supplies[] = { - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"), -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_consumer_supply sdp3430_vpll2_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - static struct regulator_consumer_supply sdp3430_vmmc1_supplies[] = { REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"), }; @@ -409,36 +399,6 @@ static struct regulator_init_data sdp3430_vsim = { .consumer_supplies = sdp3430_vsim_supplies, };
-/* VDAC for DSS driving S-Video */ -static struct regulator_init_data sdp3430_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(sdp3430_vdda_dac_supplies), - .consumer_supplies = sdp3430_vdda_dac_supplies, -}; - -static struct regulator_init_data sdp3430_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(sdp3430_vpll2_supplies), - .consumer_supplies = sdp3430_vpll2_supplies, -}; - static struct twl4030_platform_data sdp3430_twldata = { /* platform_data for children goes here */ .gpio = &sdp3430_gpio_data, @@ -451,16 +411,19 @@ static struct twl4030_platform_data sdp3430_twldata = { .vmmc1 = &sdp3430_vmmc1, .vmmc2 = &sdp3430_vmmc2, .vsim = &sdp3430_vsim, - .vdac = &sdp3430_vdac, - .vpll2 = &sdp3430_vpll2, };
static int __init omap3430_i2c_init(void) { /* i2c1 for PMIC only */ omap3_pmic_get_config(&sdp3430_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | - TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | + TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + sdp3430_twldata.vdac->constraints.apply_uV = true; + sdp3430_twldata.vpll2->constraints.apply_uV = true; + sdp3430_twldata.vpll2->constraints.name = "VDVI"; + omap3_pmic_init("twl4030", &sdp3430_twldata);
/* i2c2 on camera connector (for sensor control) and optional isp1301 */ diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c index e867474..2ae6afe 100644 --- a/arch/arm/mach-omap2/board-cm-t35.c +++ b/arch/arm/mach-omap2/board-cm-t35.c @@ -345,9 +345,6 @@ static struct regulator_consumer_supply cm_t35_vsim_supply = { .supply = "vmmc_aux", };
-static struct regulator_consumer_supply cm_t35_vdac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - static struct regulator_consumer_supply cm_t35_vdvi_supply = REGULATOR_SUPPLY("vdvi", "omapdss");
@@ -381,35 +378,6 @@ static struct regulator_init_data cm_t35_vsim = { .consumer_supplies = &cm_t35_vsim_supply, };
-/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */ -static struct regulator_init_data cm_t35_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &cm_t35_vdac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_init_data cm_t35_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &cm_t35_vdvi_supply, -}; - static uint32_t cm_t35_keymap[] = { KEY(0, 0, KEY_A), KEY(0, 1, KEY_B), KEY(0, 2, KEY_LEFT), KEY(1, 0, KEY_UP), KEY(1, 1, KEY_ENTER), KEY(1, 2, KEY_DOWN), @@ -497,13 +465,16 @@ static struct twl4030_platform_data cm_t35_twldata = { .gpio = &cm_t35_gpio_data, .vmmc1 = &cm_t35_vmmc1, .vsim = &cm_t35_vsim, - .vdac = &cm_t35_vdac, - .vpll2 = &cm_t35_vpll2, };
static void __init cm_t35_init_i2c(void) { - omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB, 0); + omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + cm_t35_twldata.vpll2->constraints.name = "VDVI"; + cm_t35_twldata.vpll2->num_consumer_supplies = 1; + cm_t35_twldata.vpll2->consumer_supplies = &cm_t35_vdvi_supply; + omap3_pmic_init("tps65930", &cm_t35_twldata); }
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index aa6a173..f7bc171 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -186,9 +186,6 @@ static struct omap_dss_board_info devkit8000_dss_data = { .default_device = &devkit8000_lcd_device, };
-static struct regulator_consumer_supply devkit8000_vdda_dac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - static uint32_t board_keymap[] = { KEY(0, 0, KEY_1), KEY(1, 0, KEY_2), @@ -288,20 +285,6 @@ static struct regulator_init_data devkit8000_vmmc1 = { .consumer_supplies = &devkit8000_vmmc1_supply, };
-/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */ -static struct regulator_init_data devkit8000_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &devkit8000_vdda_dac_supply, -}; - /* VPLL1 for digital video outputs */ static struct regulator_init_data devkit8000_vpll1 = { .constraints = { @@ -335,7 +318,6 @@ static struct twl4030_platform_data devkit8000_twldata = { /* platform_data for children goes here */ .gpio = &devkit8000_gpio_data, .vmmc1 = &devkit8000_vmmc1, - .vdac = &devkit8000_vdac, .vpll1 = &devkit8000_vpll1, .vio = &devkit8000_vio, .keypad = &devkit8000_kp_data, @@ -344,7 +326,8 @@ static struct twl4030_platform_data devkit8000_twldata = { static int __init devkit8000_i2c_init(void) { omap3_pmic_get_config(&devkit8000_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC); omap3_pmic_init("tps65930", &devkit8000_twldata); /* Bus 3 is attached to the DVI port where devices like the pico DLP * projector don't work reliably with 400kHz */ diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c index bb3723a..48f86e1 100644 --- a/arch/arm/mach-omap2/board-igep0020.c +++ b/arch/arm/mach-omap2/board-igep0020.c @@ -476,26 +476,6 @@ static struct omap_dss_board_info igep2_dss_data = { .default_device = &igep2_dvi_device, };
-static struct regulator_consumer_supply igep2_vpll2_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - -static struct regulator_init_data igep2_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(igep2_vpll2_supplies), - .consumer_supplies = igep2_vpll2_supplies, -}; - static void __init igep2_display_init(void) { int err = gpio_request_one(IGEP2_GPIO_DVI_PUP, GPIOF_OUT_INIT_HIGH, @@ -576,9 +556,11 @@ static void __init igep_i2c_init(void) pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
igep_twldata.keypad = &igep2_keypad_pdata; - igep_twldata.vpll2 = &igep2_vpll2; - /* Use common codec data */ - omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, 0); + /* Get common pmic data */ + omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VPLL2); + igep_twldata.vpll2->constraints.apply_uV = true; + igep_twldata.vpll2->constraints.name = "VDVI"; }
omap3_pmic_init("twl4030", &igep_twldata); diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 63104e8..ff991ca 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -210,14 +210,6 @@ static struct omap_dss_board_info beagle_dss_data = { .default_device = &beagle_dvi_device, };
-static struct regulator_consumer_supply beagle_vdac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - -static struct regulator_consumer_supply beagle_vdvi_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - static void __init beagle_display_init(void) { int r; @@ -355,42 +347,11 @@ static struct regulator_init_data beagle_vsim = { .consumer_supplies = &beagle_vsim_supply, };
-/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */ -static struct regulator_init_data beagle_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &beagle_vdac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_init_data beagle_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(beagle_vdvi_supplies), - .consumer_supplies = beagle_vdvi_supplies, -}; - static struct twl4030_platform_data beagle_twldata = { /* platform_data for children goes here */ .gpio = &beagle_gpio_data, .vmmc1 = &beagle_vmmc1, .vsim = &beagle_vsim, - .vdac = &beagle_vdac, - .vpll2 = &beagle_vpll2, };
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = { @@ -402,7 +363,10 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = { static int __init omap3_beagle_i2c_init(void) { omap3_pmic_get_config(&beagle_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + beagle_twldata.vpll2->constraints.name = "VDVI"; + omap3_pmic_init("twl4030", &beagle_twldata); /* Bus 3 is attached to the DVI port where devices like the pico DLP * projector don't work reliably with 400kHz */ diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 3e7e902..e6fa723 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -434,44 +434,6 @@ static struct twl4030_keypad_data omap3evm_kp_data = { .rep = 1, };
-static struct regulator_consumer_supply omap3_evm_vdda_dac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - -/* VDAC for DSS driving S-Video */ -static struct regulator_init_data omap3_evm_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &omap3_evm_vdda_dac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_consumer_supply omap3_evm_vpll2_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - -static struct regulator_init_data omap3_evm_vpll2 = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3_evm_vpll2_supplies), - .consumer_supplies = omap3_evm_vpll2_supplies, -}; - /* ads7846 on SPI */ static struct regulator_consumer_supply omap3evm_vio_supply = REGULATOR_SUPPLY("vcc", "spi1.0"); @@ -536,8 +498,6 @@ static struct twl4030_platform_data omap3evm_twldata = { /* platform_data for children goes here */ .keypad = &omap3evm_kp_data, .gpio = &omap3evm_gpio_data, - .vdac = &omap3_evm_vdac, - .vpll2 = &omap3_evm_vpll2, .vio = &omap3evm_vio, .vmmc1 = &omap3evm_vmmc1, .vsim = &omap3evm_vsim, @@ -546,8 +506,11 @@ static struct twl4030_platform_data omap3evm_twldata = { static int __init omap3_evm_i2c_init(void) { omap3_pmic_get_config(&omap3evm_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | - TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | + TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + omap3evm_twldata.vdac->constraints.apply_uV = true; + omap3evm_twldata.vpll2->constraints.apply_uV = true; omap3_pmic_init("twl4030", &omap3evm_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 7bfe109..db8b206 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -329,9 +329,6 @@ static struct regulator_consumer_supply pandora_vmmc2_supply = static struct regulator_consumer_supply pandora_vmmc3_supply = REGULATOR_SUPPLY("vmmc", "omap_hsmmc.2");
-static struct regulator_consumer_supply pandora_vdda_dac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - static struct regulator_consumer_supply pandora_vdds_supplies[] = { REGULATOR_SUPPLY("vdds_sdi", "omapdss"), REGULATOR_SUPPLY("vdds_dsi", "omapdss"), @@ -384,36 +381,6 @@ static struct regulator_init_data pandora_vmmc2 = { .consumer_supplies = &pandora_vmmc2_supply, };
-/* VDAC for DSS driving S-Video */ -static struct regulator_init_data pandora_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &pandora_vdda_dac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_init_data pandora_vpll2 = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(pandora_vdds_supplies), - .consumer_supplies = pandora_vdds_supplies, -}; - /* VAUX1 for LCD */ static struct regulator_init_data pandora_vaux1 = { .constraints = { @@ -507,8 +474,6 @@ static struct twl4030_platform_data omap3pandora_twldata = { .gpio = &omap3pandora_gpio_data, .vmmc1 = &pandora_vmmc1, .vmmc2 = &pandora_vmmc2, - .vdac = &pandora_vdac, - .vpll2 = &pandora_vpll2, .vaux1 = &pandora_vaux1, .vaux2 = &pandora_vaux2, .vaux4 = &pandora_vaux4, @@ -527,7 +492,14 @@ static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = { static int __init omap3pandora_i2c_init(void) { omap3_pmic_get_config(&omap3pandora_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + omap3pandora_twldata.vdac->constraints.apply_uV = true; + omap3pandora_twldata.vpll2->constraints.apply_uV = true; + omap3pandora_twldata.vpll2->num_consumer_supplies = + ARRAY_SIZE(pandora_vdds_supplies); + omap3pandora_twldata.vpll2->consumer_supplies = pandora_vdds_supplies; + omap3_pmic_init("tps65950", &omap3pandora_twldata); /* i2c2 pins are not connected */ omap_register_i2c_bus(3, 100, omap3pandora_i2c3_boardinfo, diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c index 2b52281..e40e08c 100644 --- a/arch/arm/mach-omap2/board-omap3stalker.c +++ b/arch/arm/mach-omap2/board-omap3stalker.c @@ -388,51 +388,10 @@ static struct twl4030_keypad_data omap3stalker_kp_data = { .rep = 1, };
-static struct regulator_consumer_supply omap3_stalker_vdda_dac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - -/* VDAC for DSS driving S-Video */ -static struct regulator_init_data omap3_stalker_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &omap3_stalker_vdda_dac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_consumer_supply omap3_stalker_vpll2_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - -static struct regulator_init_data omap3_stalker_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(omap3_stalker_vpll2_supplies), - .consumer_supplies = omap3_stalker_vpll2_supplies, -}; - static struct twl4030_platform_data omap3stalker_twldata = { /* platform_data for children goes here */ .keypad = &omap3stalker_kp_data, .gpio = &omap3stalker_gpio_data, - .vdac = &omap3_stalker_vdac, - .vpll2 = &omap3_stalker_vpll2, .vmmc1 = &omap3stalker_vmmc1, .vsim = &omap3stalker_vsim, }; @@ -455,7 +414,12 @@ static int __init omap3_stalker_i2c_init(void) { omap3_pmic_get_config(&omap3stalker_twldata, TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | - TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + omap3stalker_twldata.vdac->constraints.apply_uV = true; + omap3stalker_twldata.vpll2->constraints.apply_uV = true; + omap3stalker_twldata.vpll2->constraints.name = "VDVI"; + omap3_pmic_init("twl4030", &omap3stalker_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3, diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c index 094ea80..a0a3cf0 100644 --- a/arch/arm/mach-omap2/board-omap3touchbook.c +++ b/arch/arm/mach-omap2/board-omap3touchbook.c @@ -207,42 +207,11 @@ static struct regulator_init_data touchbook_vsim = { .consumer_supplies = &touchbook_vsim_supply, };
-/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */ -static struct regulator_init_data touchbook_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &touchbook_vdac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_init_data touchbook_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &touchbook_vdvi_supply, -}; - static struct twl4030_platform_data touchbook_twldata = { /* platform_data for children goes here */ .gpio = &touchbook_gpio_data, .vmmc1 = &touchbook_vmmc1, .vsim = &touchbook_vsim, - .vdac = &touchbook_vdac, - .vpll2 = &touchbook_vpll2, };
static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = { @@ -255,7 +224,14 @@ static int __init omap3_touchbook_i2c_init(void) { /* Standard TouchBook bus */ omap3_pmic_get_config(&touchbook_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + touchbook_twldata.vdac->num_consumer_supplies = 1; + touchbook_twldata.vdac->consumer_supplies = &touchbook_vdac_supply; + touchbook_twldata.vpll2->constraints.name = "VDVI"; + touchbook_twldata.vpll2->num_consumer_supplies = 1; + touchbook_twldata.vpll2->consumer_supplies = &touchbook_vdvi_supply; + omap3_pmic_init("twl4030", &touchbook_twldata); /* Additional TouchBook bus */ omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo, diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index f334829..e3fa177 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -264,14 +264,6 @@ static struct omap_dss_board_info overo_dss_data = { .default_device = &overo_dvi_device, };
-static struct regulator_consumer_supply overo_vdda_dac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - -static struct regulator_consumer_supply overo_vdds_dsi_supply[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - static struct mtd_partition overo_nand_partitions[] = { { .name = "xloader", @@ -447,46 +439,18 @@ static struct regulator_init_data overo_vmmc1 = { .consumer_supplies = &overo_vmmc1_supply, };
-/* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */ -static struct regulator_init_data overo_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &overo_vdda_dac_supply, -}; - -/* VPLL2 for digital video outputs */ -static struct regulator_init_data overo_vpll2 = { - .constraints = { - .name = "VDVI", - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(overo_vdds_dsi_supply), - .consumer_supplies = overo_vdds_dsi_supply, -}; - static struct twl4030_platform_data overo_twldata = { .gpio = &overo_gpio_data, .vmmc1 = &overo_vmmc1, - .vdac = &overo_vdac, - .vpll2 = &overo_vpll2, };
static int __init overo_i2c_init(void) { omap3_pmic_get_config(&overo_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); + overo_twldata.vpll2->constraints.name = "VDVI"; + omap3_pmic_init("tps65950", &overo_twldata); /* i2c2 pins are used for gpio */ omap_register_i2c_bus(3, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index dc69a7f..dfaf874 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -391,10 +391,6 @@ static struct regulator_consumer_supply rx51_vaux1_consumers[] = { REGULATOR_SUPPLY("vdd", "2-0063"), };
-static struct regulator_consumer_supply rx51_vdac_supply[] = { - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"), -}; - static struct regulator_init_data rx51_vaux1 = { .constraints = { .name = "V28", @@ -511,21 +507,6 @@ static struct regulator_init_data rx51_vsim = { .consumer_supplies = &rx51_vsim_supply, };
-static struct regulator_init_data rx51_vdac = { - .constraints = { - .name = "VDAC", - .min_uV = 1800000, - .max_uV = 1800000, - .apply_uV = true, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = rx51_vdac_supply, -}; - static struct regulator_init_data rx51_vio = { .constraints = { .min_uV = 1800000, @@ -778,7 +759,6 @@ static struct twl4030_platform_data rx51_twldata __initdata = { .vaux4 = &rx51_vaux4, .vmmc1 = &rx51_vmmc1, .vsim = &rx51_vsim, - .vdac = &rx51_vdac, .vio = &rx51_vio, };
@@ -835,7 +815,10 @@ static int __init rx51_i2c_init(void) } rx51_twldata.vmmc2 = &rx51_vmmc2; omap3_pmic_get_config(&rx51_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC, + TWL_COMMON_REGULATOR_VDAC); + rx51_twldata.vdac->constraints.apply_uV = true; + rx51_twldata.vdac->constraints.name = "VDAC"; omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata); omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2, ARRAY_SIZE(rx51_peripherals_i2c_board_info_2)); diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c index 58c0c6e..8853dc4 100644 --- a/arch/arm/mach-omap2/board-zoom-peripherals.c +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -227,40 +227,6 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ };
-static struct regulator_consumer_supply zoom_vpll2_supplies[] = { - REGULATOR_SUPPLY("vdds_dsi", "omapdss"), - REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), -}; - -static struct regulator_consumer_supply zoom_vdda_dac_supply = - REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"); - -static struct regulator_init_data zoom_vpll2 = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = ARRAY_SIZE(zoom_vpll2_supplies), - .consumer_supplies = zoom_vpll2_supplies, -}; - -static struct regulator_init_data zoom_vdac = { - .constraints = { - .min_uV = 1800000, - .max_uV = 1800000, - .valid_modes_mask = REGULATOR_MODE_NORMAL - | REGULATOR_MODE_STANDBY, - .valid_ops_mask = REGULATOR_CHANGE_MODE - | REGULATOR_CHANGE_STATUS, - }, - .num_consumer_supplies = 1, - .consumer_supplies = &zoom_vdda_dac_supply, -}; - static int zoom_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { @@ -306,15 +272,14 @@ static struct twl4030_platform_data zoom_twldata = { .vmmc1 = &zoom_vmmc1, .vmmc2 = &zoom_vmmc2, .vsim = &zoom_vsim, - .vpll2 = &zoom_vpll2, - .vdac = &zoom_vdac, };
static int __init omap_i2c_init(void) { omap3_pmic_get_config(&zoom_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | - TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, 0); + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI | + TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
if (machine_is_omap_zoom2()) { struct twl4030_codec_audio_data *audio_data; diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 2487e3c..f15f880 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -87,6 +87,41 @@ static struct twl4030_codec_data omap3_codec_pdata = { .audio = &omap3_audio, };
+static struct regulator_consumer_supply omap3_vdda_dac_supplies[] = { + REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"), +}; + +static struct regulator_init_data omap3_vdac_idata = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(omap3_vdda_dac_supplies), + .consumer_supplies = omap3_vdda_dac_supplies, +}; + +static struct regulator_consumer_supply omap3_vpll2_supplies[] = { + REGULATOR_SUPPLY("vdds_dsi", "omapdss"), + REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"), +}; + +static struct regulator_init_data omap3_vpll2_idata = { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(omap3_vpll2_supplies), + .consumer_supplies = omap3_vpll2_supplies, +}; + static struct regulator_init_data omap4_vdac_idata = { .constraints = { .min_uV = 1800000, @@ -259,4 +294,11 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->codec) pmic_data->codec = &omap3_codec_pdata; + + /* Common regulator configurations */ + if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac) + pmic_data->vdac = &omap3_vdac_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VPLL2 && !pmic_data->vpll2) + pmic_data->vpll2 = &omap3_vpll2_idata; } diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h index 3b4b05d..5e83a5b 100644 --- a/arch/arm/mach-omap2/twl-common.h +++ b/arch/arm/mach-omap2/twl-common.h @@ -21,6 +21,11 @@ #define TWL_COMMON_REGULATOR_VUSB (1 << 9) #define TWL_COMMON_REGULATOR_CLK32KG (1 << 10)
+/* TWL4030 LDO regulators */ +#define TWL_COMMON_REGULATOR_VPLL1 (1 << 4) +#define TWL_COMMON_REGULATOR_VPLL2 (1 << 5) + + struct twl4030_platform_data;
void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq,
In preparation of renaming the driver from twl4030-codec to twl4030-audio, first do some clean ups in the driver, which does not cause any problems outside.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- drivers/mfd/twl4030-codec.c | 135 ++++++++++++++++++++++--------------------- 1 files changed, 68 insertions(+), 67 deletions(-)
diff --git a/drivers/mfd/twl4030-codec.c b/drivers/mfd/twl4030-codec.c index 2bf4136..e1782b3 100644 --- a/drivers/mfd/twl4030-codec.c +++ b/drivers/mfd/twl4030-codec.c @@ -1,5 +1,6 @@ /* - * MFD driver for twl4030 codec submodule + * MFD driver for twl4030 audio submodule, which contains an audio codec, and + * the vibra control. * * Author: Peter Ujfalusi peter.ujfalusi@ti.com * @@ -31,53 +32,53 @@ #include <linux/mfd/core.h> #include <linux/mfd/twl4030-codec.h>
-#define TWL4030_CODEC_CELLS 2 +#define TWL4030_AUDIO_CELLS 2
-static struct platform_device *twl4030_codec_dev; +static struct platform_device *twl4030_audio_dev;
-struct twl4030_codec_resource { +struct twl4030_audio_resource { int request_count; u8 reg; u8 mask; };
-struct twl4030_codec { +struct twl4030_audio { unsigned int audio_mclk; struct mutex mutex; - struct twl4030_codec_resource resource[TWL4030_CODEC_RES_MAX]; - struct mfd_cell cells[TWL4030_CODEC_CELLS]; + struct twl4030_audio_resource resource[TWL4030_CODEC_RES_MAX]; + struct mfd_cell cells[TWL4030_AUDIO_CELLS]; };
/* * Modify the resource, the function returns the content of the register * after the modification. */ -static int twl4030_codec_set_resource(enum twl4030_codec_res id, int enable) +static int twl4030_audio_set_resource(enum twl4030_codec_res id, int enable) { - struct twl4030_codec *codec = platform_get_drvdata(twl4030_codec_dev); + struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); u8 val;
twl_i2c_read_u8(TWL4030_MODULE_AUDIO_VOICE, &val, - codec->resource[id].reg); + audio->resource[id].reg);
if (enable) - val |= codec->resource[id].mask; + val |= audio->resource[id].mask; else - val &= ~codec->resource[id].mask; + val &= ~audio->resource[id].mask;
twl_i2c_write_u8(TWL4030_MODULE_AUDIO_VOICE, - val, codec->resource[id].reg); + val, audio->resource[id].reg);
return val; }
-static inline int twl4030_codec_get_resource(enum twl4030_codec_res id) +static inline int twl4030_audio_get_resource(enum twl4030_codec_res id) { - struct twl4030_codec *codec = platform_get_drvdata(twl4030_codec_dev); + struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); u8 val;
twl_i2c_read_u8(TWL4030_MODULE_AUDIO_VOICE, &val, - codec->resource[id].reg); + audio->resource[id].reg);
return val; } @@ -88,24 +89,24 @@ static inline int twl4030_codec_get_resource(enum twl4030_codec_res id) */ int twl4030_codec_enable_resource(enum twl4030_codec_res id) { - struct twl4030_codec *codec = platform_get_drvdata(twl4030_codec_dev); + struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); int val;
if (id >= TWL4030_CODEC_RES_MAX) { - dev_err(&twl4030_codec_dev->dev, + dev_err(&twl4030_audio_dev->dev, "Invalid resource ID (%u)\n", id); return -EINVAL; }
- mutex_lock(&codec->mutex); - if (!codec->resource[id].request_count) + mutex_lock(&audio->mutex); + if (!audio->resource[id].request_count) /* Resource was disabled, enable it */ - val = twl4030_codec_set_resource(id, 1); + val = twl4030_audio_set_resource(id, 1); else - val = twl4030_codec_get_resource(id); + val = twl4030_audio_get_resource(id);
- codec->resource[id].request_count++; - mutex_unlock(&codec->mutex); + audio->resource[id].request_count++; + mutex_unlock(&audio->mutex);
return val; } @@ -117,31 +118,31 @@ EXPORT_SYMBOL_GPL(twl4030_codec_enable_resource); */ int twl4030_codec_disable_resource(unsigned id) { - struct twl4030_codec *codec = platform_get_drvdata(twl4030_codec_dev); + struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); int val;
if (id >= TWL4030_CODEC_RES_MAX) { - dev_err(&twl4030_codec_dev->dev, + dev_err(&twl4030_audio_dev->dev, "Invalid resource ID (%u)\n", id); return -EINVAL; }
- mutex_lock(&codec->mutex); - if (!codec->resource[id].request_count) { - dev_err(&twl4030_codec_dev->dev, + mutex_lock(&audio->mutex); + if (!audio->resource[id].request_count) { + dev_err(&twl4030_audio_dev->dev, "Resource has been disabled already (%u)\n", id); - mutex_unlock(&codec->mutex); + mutex_unlock(&audio->mutex); return -EPERM; } - codec->resource[id].request_count--; + audio->resource[id].request_count--;
- if (!codec->resource[id].request_count) + if (!audio->resource[id].request_count) /* Resource can be disabled now */ - val = twl4030_codec_set_resource(id, 0); + val = twl4030_audio_set_resource(id, 0); else - val = twl4030_codec_get_resource(id); + val = twl4030_audio_get_resource(id);
- mutex_unlock(&codec->mutex); + mutex_unlock(&audio->mutex);
return val; } @@ -149,15 +150,15 @@ EXPORT_SYMBOL_GPL(twl4030_codec_disable_resource);
unsigned int twl4030_codec_get_mclk(void) { - struct twl4030_codec *codec = platform_get_drvdata(twl4030_codec_dev); + struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev);
- return codec->audio_mclk; + return audio->audio_mclk; } EXPORT_SYMBOL_GPL(twl4030_codec_get_mclk);
-static int __devinit twl4030_codec_probe(struct platform_device *pdev) +static int __devinit twl4030_audio_probe(struct platform_device *pdev) { - struct twl4030_codec *codec; + struct twl4030_audio *audio; struct twl4030_codec_data *pdata = pdev->dev.platform_data; struct mfd_cell *cell = NULL; int ret, childs = 0; @@ -187,33 +188,33 @@ static int __devinit twl4030_codec_probe(struct platform_device *pdev) twl_i2c_write_u8(TWL4030_MODULE_AUDIO_VOICE, val, TWL4030_REG_APLL_CTL);
- codec = kzalloc(sizeof(struct twl4030_codec), GFP_KERNEL); - if (!codec) + audio = kzalloc(sizeof(struct twl4030_audio), GFP_KERNEL); + if (!audio) return -ENOMEM;
- platform_set_drvdata(pdev, codec); + platform_set_drvdata(pdev, audio);
- twl4030_codec_dev = pdev; - mutex_init(&codec->mutex); - codec->audio_mclk = pdata->audio_mclk; + twl4030_audio_dev = pdev; + mutex_init(&audio->mutex); + audio->audio_mclk = pdata->audio_mclk;
/* Codec power */ - codec->resource[TWL4030_CODEC_RES_POWER].reg = TWL4030_REG_CODEC_MODE; - codec->resource[TWL4030_CODEC_RES_POWER].mask = TWL4030_CODECPDZ; + audio->resource[TWL4030_CODEC_RES_POWER].reg = TWL4030_REG_CODEC_MODE; + audio->resource[TWL4030_CODEC_RES_POWER].mask = TWL4030_CODECPDZ;
/* PLL */ - codec->resource[TWL4030_CODEC_RES_APLL].reg = TWL4030_REG_APLL_CTL; - codec->resource[TWL4030_CODEC_RES_APLL].mask = TWL4030_APLL_EN; + audio->resource[TWL4030_CODEC_RES_APLL].reg = TWL4030_REG_APLL_CTL; + audio->resource[TWL4030_CODEC_RES_APLL].mask = TWL4030_APLL_EN;
if (pdata->audio) { - cell = &codec->cells[childs]; + cell = &audio->cells[childs]; cell->name = "twl4030-codec"; cell->platform_data = pdata->audio; cell->pdata_size = sizeof(*pdata->audio); childs++; } if (pdata->vibra) { - cell = &codec->cells[childs]; + cell = &audio->cells[childs]; cell->name = "twl4030-vibra"; cell->platform_data = pdata->vibra; cell->pdata_size = sizeof(*pdata->vibra); @@ -221,7 +222,7 @@ static int __devinit twl4030_codec_probe(struct platform_device *pdev) }
if (childs) - ret = mfd_add_devices(&pdev->dev, pdev->id, codec->cells, + ret = mfd_add_devices(&pdev->dev, pdev->id, audio->cells, childs, NULL, 0); else { dev_err(&pdev->dev, "No platform data found for childs\n"); @@ -232,45 +233,45 @@ static int __devinit twl4030_codec_probe(struct platform_device *pdev) return 0;
platform_set_drvdata(pdev, NULL); - kfree(codec); - twl4030_codec_dev = NULL; + kfree(audio); + twl4030_audio_dev = NULL; return ret; }
-static int __devexit twl4030_codec_remove(struct platform_device *pdev) +static int __devexit twl4030_audio_remove(struct platform_device *pdev) { - struct twl4030_codec *codec = platform_get_drvdata(pdev); + struct twl4030_audio *audio = platform_get_drvdata(pdev);
mfd_remove_devices(&pdev->dev); platform_set_drvdata(pdev, NULL); - kfree(codec); - twl4030_codec_dev = NULL; + kfree(audio); + twl4030_audio_dev = NULL;
return 0; }
MODULE_ALIAS("platform:twl4030-audio");
-static struct platform_driver twl4030_codec_driver = { - .probe = twl4030_codec_probe, - .remove = __devexit_p(twl4030_codec_remove), +static struct platform_driver twl4030_audio_driver = { + .probe = twl4030_audio_probe, + .remove = __devexit_p(twl4030_audio_remove), .driver = { .owner = THIS_MODULE, .name = "twl4030-audio", }, };
-static int __devinit twl4030_codec_init(void) +static int __devinit twl4030_audio_init(void) { - return platform_driver_register(&twl4030_codec_driver); + return platform_driver_register(&twl4030_audio_driver); } -module_init(twl4030_codec_init); +module_init(twl4030_audio_init);
-static void __devexit twl4030_codec_exit(void) +static void __devexit twl4030_audio_exit(void) { - platform_driver_unregister(&twl4030_codec_driver); + platform_driver_unregister(&twl4030_audio_driver); } -module_exit(twl4030_codec_exit); +module_exit(twl4030_audio_exit);
MODULE_AUTHOR("Peter Ujfalusi peter.ujfalusi@ti.com"); MODULE_LICENSE("GPL");
Rename the driver, and header file from twl4030-codec to twl4030-audio. To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com CC: Misael Lopez Cruz misael.lopez@ti.com --- drivers/input/misc/Kconfig | 2 +- drivers/input/misc/twl4030-vibra.c | 10 +++--- drivers/mfd/Kconfig | 2 +- drivers/mfd/Makefile | 2 +- drivers/mfd/{twl4030-codec.c => twl4030-audio.c} | 33 +++++++++---------- .../linux/mfd/{twl4030-codec.h => twl4030-audio.h} | 16 +++++----- sound/soc/codecs/Kconfig | 2 +- sound/soc/codecs/twl4030.c | 16 +++++----- sound/soc/omap/sdp3430.c | 2 +- sound/soc/omap/zoom2.c | 2 +- 10 files changed, 43 insertions(+), 44 deletions(-) rename drivers/mfd/{twl4030-codec.c => twl4030-audio.c} (87%) rename include/linux/mfd/{twl4030-codec.h => twl4030-audio.h} (96%)
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 45dc6aa..077309a 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -267,7 +267,7 @@ config INPUT_TWL4030_PWRBUTTON config INPUT_TWL4030_VIBRA tristate "Support for TWL4030 Vibrator" depends on TWL4030_CORE - select TWL4030_CODEC + select MFD_TWL4030_AUDIO select INPUT_FF_MEMLESS help This option enables support for TWL4030 Vibrator Driver. diff --git a/drivers/input/misc/twl4030-vibra.c b/drivers/input/misc/twl4030-vibra.c index 014dd4a..7abca85 100644 --- a/drivers/input/misc/twl4030-vibra.c +++ b/drivers/input/misc/twl4030-vibra.c @@ -28,7 +28,7 @@ #include <linux/platform_device.h> #include <linux/workqueue.h> #include <linux/i2c/twl.h> -#include <linux/mfd/twl4030-codec.h> +#include <linux/mfd/twl4030-audio.h> #include <linux/input.h> #include <linux/slab.h>
@@ -67,7 +67,7 @@ static void vibra_enable(struct vibra_info *info) { u8 reg;
- twl4030_codec_enable_resource(TWL4030_CODEC_RES_POWER); + twl4030_audio_enable_resource(TWL4030_AUDIO_RES_POWER);
/* turn H-Bridge on */ twl_i2c_read_u8(TWL4030_MODULE_AUDIO_VOICE, @@ -75,7 +75,7 @@ static void vibra_enable(struct vibra_info *info) twl_i2c_write_u8(TWL4030_MODULE_AUDIO_VOICE, (reg | TWL4030_VIBRA_EN), TWL4030_REG_VIBRA_CTL);
- twl4030_codec_enable_resource(TWL4030_CODEC_RES_APLL); + twl4030_audio_enable_resource(TWL4030_AUDIO_RES_APLL);
info->enabled = true; } @@ -90,8 +90,8 @@ static void vibra_disable(struct vibra_info *info) twl_i2c_write_u8(TWL4030_MODULE_AUDIO_VOICE, (reg & ~TWL4030_VIBRA_EN), TWL4030_REG_VIBRA_CTL);
- twl4030_codec_disable_resource(TWL4030_CODEC_RES_APLL); - twl4030_codec_disable_resource(TWL4030_CODEC_RES_POWER); + twl4030_audio_disable_resource(TWL4030_AUDIO_RES_APLL); + twl4030_audio_disable_resource(TWL4030_AUDIO_RES_POWER);
info->enabled = false; } diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 519ebab..30f3536 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -240,7 +240,7 @@ config TWL4030_POWER and load scripts controlling which resources are switched off/on or reset when a sleep, wakeup or warm reset event occurs.
-config TWL4030_CODEC +config MFD_TWL4030_AUDIO bool depends on TWL4030_CORE select MFD_CORE diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 5309ec3..77cb99a 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -45,7 +45,7 @@ obj-$(CONFIG_MENELAUS) += menelaus.o obj-$(CONFIG_TWL4030_CORE) += twl-core.o twl4030-irq.o twl6030-irq.o obj-$(CONFIG_TWL4030_MADC) += twl4030-madc.o obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o -obj-$(CONFIG_TWL4030_CODEC) += twl4030-codec.o +obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o obj-$(CONFIG_TWL6030_PWM) += twl6030-pwm.o
obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o diff --git a/drivers/mfd/twl4030-codec.c b/drivers/mfd/twl4030-audio.c similarity index 87% rename from drivers/mfd/twl4030-codec.c rename to drivers/mfd/twl4030-audio.c index e1782b3..5cdf841 100644 --- a/drivers/mfd/twl4030-codec.c +++ b/drivers/mfd/twl4030-audio.c @@ -30,7 +30,7 @@ #include <linux/platform_device.h> #include <linux/i2c/twl.h> #include <linux/mfd/core.h> -#include <linux/mfd/twl4030-codec.h> +#include <linux/mfd/twl4030-audio.h>
#define TWL4030_AUDIO_CELLS 2
@@ -45,7 +45,7 @@ struct twl4030_audio_resource { struct twl4030_audio { unsigned int audio_mclk; struct mutex mutex; - struct twl4030_audio_resource resource[TWL4030_CODEC_RES_MAX]; + struct twl4030_audio_resource resource[TWL4030_AUDIO_RES_MAX]; struct mfd_cell cells[TWL4030_AUDIO_CELLS]; };
@@ -53,7 +53,7 @@ struct twl4030_audio { * Modify the resource, the function returns the content of the register * after the modification. */ -static int twl4030_audio_set_resource(enum twl4030_codec_res id, int enable) +static int twl4030_audio_set_resource(enum twl4030_audio_res id, int enable) { struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); u8 val; @@ -72,7 +72,7 @@ static int twl4030_audio_set_resource(enum twl4030_codec_res id, int enable) return val; }
-static inline int twl4030_audio_get_resource(enum twl4030_codec_res id) +static inline int twl4030_audio_get_resource(enum twl4030_audio_res id) { struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); u8 val; @@ -87,12 +87,12 @@ static inline int twl4030_audio_get_resource(enum twl4030_codec_res id) * Enable the resource. * The function returns with error or the content of the register */ -int twl4030_codec_enable_resource(enum twl4030_codec_res id) +int twl4030_audio_enable_resource(enum twl4030_audio_res id) { struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); int val;
- if (id >= TWL4030_CODEC_RES_MAX) { + if (id >= TWL4030_AUDIO_RES_MAX) { dev_err(&twl4030_audio_dev->dev, "Invalid resource ID (%u)\n", id); return -EINVAL; @@ -110,18 +110,18 @@ int twl4030_codec_enable_resource(enum twl4030_codec_res id)
return val; } -EXPORT_SYMBOL_GPL(twl4030_codec_enable_resource); +EXPORT_SYMBOL_GPL(twl4030_audio_enable_resource);
/* * Disable the resource. * The function returns with error or the content of the register */ -int twl4030_codec_disable_resource(unsigned id) +int twl4030_audio_disable_resource(unsigned id) { struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev); int val;
- if (id >= TWL4030_CODEC_RES_MAX) { + if (id >= TWL4030_AUDIO_RES_MAX) { dev_err(&twl4030_audio_dev->dev, "Invalid resource ID (%u)\n", id); return -EINVAL; @@ -146,15 +146,15 @@ int twl4030_codec_disable_resource(unsigned id)
return val; } -EXPORT_SYMBOL_GPL(twl4030_codec_disable_resource); +EXPORT_SYMBOL_GPL(twl4030_audio_disable_resource);
-unsigned int twl4030_codec_get_mclk(void) +unsigned int twl4030_audio_get_mclk(void) { struct twl4030_audio *audio = platform_get_drvdata(twl4030_audio_dev);
return audio->audio_mclk; } -EXPORT_SYMBOL_GPL(twl4030_codec_get_mclk); +EXPORT_SYMBOL_GPL(twl4030_audio_get_mclk);
static int __devinit twl4030_audio_probe(struct platform_device *pdev) { @@ -199,12 +199,12 @@ static int __devinit twl4030_audio_probe(struct platform_device *pdev) audio->audio_mclk = pdata->audio_mclk;
/* Codec power */ - audio->resource[TWL4030_CODEC_RES_POWER].reg = TWL4030_REG_CODEC_MODE; - audio->resource[TWL4030_CODEC_RES_POWER].mask = TWL4030_CODECPDZ; + audio->resource[TWL4030_AUDIO_RES_POWER].reg = TWL4030_REG_CODEC_MODE; + audio->resource[TWL4030_AUDIO_RES_POWER].mask = TWL4030_CODECPDZ;
/* PLL */ - audio->resource[TWL4030_CODEC_RES_APLL].reg = TWL4030_REG_APLL_CTL; - audio->resource[TWL4030_CODEC_RES_APLL].mask = TWL4030_APLL_EN; + audio->resource[TWL4030_AUDIO_RES_APLL].reg = TWL4030_REG_APLL_CTL; + audio->resource[TWL4030_AUDIO_RES_APLL].mask = TWL4030_APLL_EN;
if (pdata->audio) { cell = &audio->cells[childs]; @@ -275,4 +275,3 @@ module_exit(twl4030_audio_exit);
MODULE_AUTHOR("Peter Ujfalusi peter.ujfalusi@ti.com"); MODULE_LICENSE("GPL"); - diff --git a/include/linux/mfd/twl4030-codec.h b/include/linux/mfd/twl4030-audio.h similarity index 96% rename from include/linux/mfd/twl4030-codec.h rename to include/linux/mfd/twl4030-audio.h index 5cc16bb..3d22b72 100644 --- a/include/linux/mfd/twl4030-codec.h +++ b/include/linux/mfd/twl4030-audio.h @@ -1,5 +1,5 @@ /* - * MFD driver for twl4030 codec submodule + * MFD driver for twl4030 audio submodule * * Author: Peter Ujfalusi peter.ujfalusi@ti.com * @@ -259,14 +259,14 @@ #define TWL4030_VIBRA_DIR_SEL 0x20
/* TWL4030 codec resource IDs */ -enum twl4030_codec_res { - TWL4030_CODEC_RES_POWER = 0, - TWL4030_CODEC_RES_APLL, - TWL4030_CODEC_RES_MAX, +enum twl4030_audio_res { + TWL4030_AUDIO_RES_POWER = 0, + TWL4030_AUDIO_RES_APLL, + TWL4030_AUDIO_RES_MAX, };
-int twl4030_codec_disable_resource(enum twl4030_codec_res id); -int twl4030_codec_enable_resource(enum twl4030_codec_res id); -unsigned int twl4030_codec_get_mclk(void); +int twl4030_audio_disable_resource(enum twl4030_audio_res id); +int twl4030_audio_enable_resource(enum twl4030_audio_res id); +unsigned int twl4030_audio_get_mclk(void);
#endif /* End of __TWL4030_CODEC_H__ */ diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 98175a0..0002220 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -236,7 +236,7 @@ config SND_SOC_TLV320DAC33 tristate
config SND_SOC_TWL4030 - select TWL4030_CODEC + select MFD_TWL4030_AUDIO tristate
config SND_SOC_TWL6040 diff --git a/sound/soc/codecs/twl4030.c b/sound/soc/codecs/twl4030.c index bec788b..5e648d3 100644 --- a/sound/soc/codecs/twl4030.c +++ b/sound/soc/codecs/twl4030.c @@ -36,7 +36,7 @@ #include <sound/tlv.h>
/* Register descriptions are here */ -#include <linux/mfd/twl4030-codec.h> +#include <linux/mfd/twl4030-audio.h>
/* Shadow register used by the audio driver */ #define TWL4030_REG_SW_SHADOW 0x4A @@ -251,9 +251,9 @@ static void twl4030_codec_enable(struct snd_soc_codec *codec, int enable) return;
if (enable) - mode = twl4030_codec_enable_resource(TWL4030_CODEC_RES_POWER); + mode = twl4030_audio_enable_resource(TWL4030_AUDIO_RES_POWER); else - mode = twl4030_codec_disable_resource(TWL4030_CODEC_RES_POWER); + mode = twl4030_audio_disable_resource(TWL4030_AUDIO_RES_POWER);
if (mode >= 0) { twl4030_write_reg_cache(codec, TWL4030_REG_CODEC_MODE, mode); @@ -375,13 +375,13 @@ static void twl4030_apll_enable(struct snd_soc_codec *codec, int enable) if (enable) { twl4030->apll_enabled++; if (twl4030->apll_enabled == 1) - status = twl4030_codec_enable_resource( - TWL4030_CODEC_RES_APLL); + status = twl4030_audio_enable_resource( + TWL4030_AUDIO_RES_APLL); } else { twl4030->apll_enabled--; if (!twl4030->apll_enabled) - status = twl4030_codec_disable_resource( - TWL4030_CODEC_RES_APLL); + status = twl4030_audio_disable_resource( + TWL4030_AUDIO_RES_APLL); }
if (status >= 0) @@ -2260,7 +2260,7 @@ static int twl4030_soc_probe(struct snd_soc_codec *codec) } snd_soc_codec_set_drvdata(codec, twl4030); /* Set the defaults, and power up the codec */ - twl4030->sysclk = twl4030_codec_get_mclk() / 1000; + twl4030->sysclk = twl4030_audio_get_mclk() / 1000; codec->dapm.idle_bias_off = 1;
twl4030_init_chip(codec); diff --git a/sound/soc/omap/sdp3430.c b/sound/soc/omap/sdp3430.c index 3f72d17..9f6a758 100644 --- a/sound/soc/omap/sdp3430.c +++ b/sound/soc/omap/sdp3430.c @@ -36,7 +36,7 @@ #include <plat/mcbsp.h>
/* Register descriptions for twl4030 codec part */ -#include <linux/mfd/twl4030-codec.h> +#include <linux/mfd/twl4030-audio.h>
#include "omap-mcbsp.h" #include "omap-pcm.h" diff --git a/sound/soc/omap/zoom2.c b/sound/soc/omap/zoom2.c index 0170994..9a2666f 100644 --- a/sound/soc/omap/zoom2.c +++ b/sound/soc/omap/zoom2.c @@ -32,7 +32,7 @@ #include <plat/mcbsp.h>
/* Register descriptions for twl4030 codec part */ -#include <linux/mfd/twl4030-codec.h> +#include <linux/mfd/twl4030-audio.h>
#include "omap-mcbsp.h" #include "omap-pcm.h"
Allign the platform data names for twl4030 audio submodule: twl4030_audio_data: for the core MFD driver twl4030_codec_data: for ASoC codec driver twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files to use the new types.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/board-rx51-peripherals.c | 6 +++--- arch/arm/mach-omap2/board-zoom-peripherals.c | 10 +++++----- arch/arm/mach-omap2/twl-common.c | 10 +++++----- drivers/input/misc/twl4030-vibra.c | 2 +- drivers/mfd/twl-core.c | 8 ++++---- drivers/mfd/twl4030-audio.c | 8 ++++---- include/linux/i2c/twl.h | 12 ++++++------ sound/soc/codecs/twl4030.c | 6 +++--- sound/soc/codecs/twl6040.c | 2 +- 9 files changed, 32 insertions(+), 32 deletions(-)
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index dfaf874..a2d3e19 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -738,11 +738,11 @@ static struct twl4030_power_data rx51_t2scripts_data __initdata = { .resource_config = twl4030_rconfig, };
-struct twl4030_codec_vibra_data rx51_vibra_data __initdata = { +struct twl4030_vibra_data rx51_vibra_data __initdata = { .coexist = 0, };
-struct twl4030_codec_data rx51_codec_data __initdata = { +struct twl4030_audio_data rx51_audio_data __initdata = { .audio_mclk = 26000000, .vibra = &rx51_vibra_data, }; @@ -752,7 +752,7 @@ static struct twl4030_platform_data rx51_twldata __initdata = { .gpio = &rx51_gpio_data, .keypad = &rx51_kp_data, .power = &rx51_t2scripts_data, - .codec = &rx51_codec_data, + .audio = &rx51_audio_data,
.vaux1 = &rx51_vaux1, .vaux2 = &rx51_vaux2, diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c index 8853dc4..6d44409 100644 --- a/arch/arm/mach-omap2/board-zoom-peripherals.c +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -282,12 +282,12 @@ static int __init omap_i2c_init(void) TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
if (machine_is_omap_zoom2()) { - struct twl4030_codec_audio_data *audio_data; - audio_data = zoom_twldata.codec->audio; + struct twl4030_codec_data *codec_data; + codec_data = zoom_twldata.audio->codec;
- audio_data->ramp_delay_value = 3; /* 161 ms */ - audio_data->hs_extmute = 1; - audio_data->set_hs_extmute = zoom2_set_hs_extmute; + codec_data->ramp_delay_value = 3; /* 161 ms */ + codec_data->hs_extmute = 1; + codec_data->set_hs_extmute = zoom2_set_hs_extmute; } omap_pmic_init(1, 2400, "twl5030", INT_34XX_SYS_NIRQ, &zoom_twldata); omap_register_i2c_bus(2, 400, NULL, 0); diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index f15f880..ca219ea 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -80,11 +80,11 @@ static struct twl4030_madc_platform_data omap3_madc_pdata = { .irq_line = 1, };
-static struct twl4030_codec_audio_data omap3_audio; +static struct twl4030_codec_data omap3_codec;
-static struct twl4030_codec_data omap3_codec_pdata = { +static struct twl4030_audio_data omap3_audio_pdata = { .audio_mclk = 26000000, - .audio = &omap3_audio, + .codec = &omap3_codec, };
static struct regulator_consumer_supply omap3_vdda_dac_supplies[] = { @@ -292,8 +292,8 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data, if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc) pmic_data->madc = &omap3_madc_pdata;
- if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->codec) - pmic_data->codec = &omap3_codec_pdata; + if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->audio) + pmic_data->audio = &omap3_audio_pdata;
/* Common regulator configurations */ if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac) diff --git a/drivers/input/misc/twl4030-vibra.c b/drivers/input/misc/twl4030-vibra.c index 7abca85..3c1a432 100644 --- a/drivers/input/misc/twl4030-vibra.c +++ b/drivers/input/misc/twl4030-vibra.c @@ -196,7 +196,7 @@ static SIMPLE_DEV_PM_OPS(twl4030_vibra_pm_ops,
static int __devinit twl4030_vibra_probe(struct platform_device *pdev) { - struct twl4030_codec_vibra_data *pdata = pdev->dev.platform_data; + struct twl4030_vibra_data *pdata = pdev->dev.platform_data; struct vibra_info *info; int ret;
diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c index b8f2a4e..f9d7880 100644 --- a/drivers/mfd/twl-core.c +++ b/drivers/mfd/twl-core.c @@ -815,20 +815,20 @@ add_children(struct twl4030_platform_data *pdata, unsigned long features) return PTR_ERR(child); }
- if (twl_has_codec() && pdata->codec && twl_class_is_4030()) { + if (twl_has_codec() && pdata->audio && twl_class_is_4030()) { sub_chip_id = twl_map[TWL_MODULE_AUDIO_VOICE].sid; child = add_child(sub_chip_id, "twl4030-audio", - pdata->codec, sizeof(*pdata->codec), + pdata->audio, sizeof(*pdata->audio), false, 0, 0); if (IS_ERR(child)) return PTR_ERR(child); }
/* Phoenix codec driver is probed directly atm */ - if (twl_has_codec() && pdata->codec && twl_class_is_6030()) { + if (twl_has_codec() && pdata->audio && twl_class_is_6030()) { sub_chip_id = twl_map[TWL_MODULE_AUDIO_VOICE].sid; child = add_child(sub_chip_id, "twl6040-codec", - pdata->codec, sizeof(*pdata->codec), + pdata->audio, sizeof(*pdata->audio), false, 0, 0); if (IS_ERR(child)) return PTR_ERR(child); diff --git a/drivers/mfd/twl4030-audio.c b/drivers/mfd/twl4030-audio.c index 5cdf841..ae51ab5 100644 --- a/drivers/mfd/twl4030-audio.c +++ b/drivers/mfd/twl4030-audio.c @@ -159,7 +159,7 @@ EXPORT_SYMBOL_GPL(twl4030_audio_get_mclk); static int __devinit twl4030_audio_probe(struct platform_device *pdev) { struct twl4030_audio *audio; - struct twl4030_codec_data *pdata = pdev->dev.platform_data; + struct twl4030_audio_data *pdata = pdev->dev.platform_data; struct mfd_cell *cell = NULL; int ret, childs = 0; u8 val; @@ -206,11 +206,11 @@ static int __devinit twl4030_audio_probe(struct platform_device *pdev) audio->resource[TWL4030_AUDIO_RES_APLL].reg = TWL4030_REG_APLL_CTL; audio->resource[TWL4030_AUDIO_RES_APLL].mask = TWL4030_APLL_EN;
- if (pdata->audio) { + if (pdata->codec) { cell = &audio->cells[childs]; cell->name = "twl4030-codec"; - cell->platform_data = pdata->audio; - cell->pdata_size = sizeof(*pdata->audio); + cell->platform_data = pdata->codec; + cell->pdata_size = sizeof(*pdata->codec); childs++; } if (pdata->vibra) { diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index ba4f886..e0aba2b 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -657,7 +657,7 @@ struct twl4030_power_data { extern void twl4030_power_init(struct twl4030_power_data *triton2_scripts); extern int twl4030_remove_script(u8 flags);
-struct twl4030_codec_audio_data { +struct twl4030_codec_data { unsigned int digimic_delay; /* in ms */ unsigned int ramp_delay_value; unsigned int offset_cncl_path; @@ -667,14 +667,14 @@ struct twl4030_codec_audio_data { void (*set_hs_extmute)(int mute); };
-struct twl4030_codec_vibra_data { +struct twl4030_vibra_data { unsigned int coexist; };
-struct twl4030_codec_data { +struct twl4030_audio_data { unsigned int audio_mclk; - struct twl4030_codec_audio_data *audio; - struct twl4030_codec_vibra_data *vibra; + struct twl4030_codec_data *codec; + struct twl4030_vibra_data *vibra;
/* twl6040 */ int audpwron_gpio; /* audio power-on gpio */ @@ -690,7 +690,7 @@ struct twl4030_platform_data { struct twl4030_keypad_data *keypad; struct twl4030_usb_data *usb; struct twl4030_power_data *power; - struct twl4030_codec_data *codec; + struct twl4030_audio_data *audio;
/* Common LDO regulators for TWL4030/TWL6030 */ struct regulator_init_data *vdac; diff --git a/sound/soc/codecs/twl4030.c b/sound/soc/codecs/twl4030.c index 5e648d3..71674be 100644 --- a/sound/soc/codecs/twl4030.c +++ b/sound/soc/codecs/twl4030.c @@ -297,7 +297,7 @@ static inline void twl4030_reset_registers(struct snd_soc_codec *codec)
static void twl4030_init_chip(struct snd_soc_codec *codec) { - struct twl4030_codec_audio_data *pdata = dev_get_platdata(codec->dev); + struct twl4030_codec_data *pdata = dev_get_platdata(codec->dev); struct twl4030_priv *twl4030 = snd_soc_codec_get_drvdata(codec); u8 reg, byte; int i = 0; @@ -732,7 +732,7 @@ static int aif_event(struct snd_soc_dapm_widget *w,
static void headset_ramp(struct snd_soc_codec *codec, int ramp) { - struct twl4030_codec_audio_data *pdata = codec->dev->platform_data; + struct twl4030_codec_data *pdata = codec->dev->platform_data; unsigned char hs_gain, hs_pop; struct twl4030_priv *twl4030 = snd_soc_codec_get_drvdata(codec); /* Base values for ramp delay calculation: 2^19 - 2^26 */ @@ -2297,7 +2297,7 @@ static struct snd_soc_codec_driver soc_codec_dev_twl4030 = {
static int __devinit twl4030_codec_probe(struct platform_device *pdev) { - struct twl4030_codec_audio_data *pdata = pdev->dev.platform_data; + struct twl4030_codec_data *pdata = pdev->dev.platform_data;
if (!pdata) { dev_err(&pdev->dev, "platform_data is missing\n"); diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index 4c33663..ade6616 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -1600,7 +1600,7 @@ static int twl6040_resume(struct snd_soc_codec *codec)
static int twl6040_probe(struct snd_soc_codec *codec) { - struct twl4030_codec_data *twl_codec = codec->dev->platform_data; + struct twl4030_audio_data *twl_codec = codec->dev->platform_data; struct twl6040_data *priv; int audpwron, naudint; int ret = 0;
From: Misael Lopez Cruz misael.lopez@ti.com
TWL6040 IC provides analog high-end audio codec functions for handset applications. It contains several audio analog inputs and outputs as well as vibrator support. It's connected to the host processor via PDM interface for audio data communication. The audio modules are controlled by internal registers that can be accessed by I2C and PDM interface.
TWL6040 MFD will be registered as a child of TWL-CORE, and will have two children of its own: twl6040-codec and twl6040-vibra.
This driver is based on TWL4030 and WM8350 MFD drivers.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/plat-omap/include/plat/irqs.h | 12 +- drivers/mfd/Kconfig | 6 + drivers/mfd/Makefile | 1 + drivers/mfd/twl-core.c | 5 +- drivers/mfd/twl6040-core.c | 602 ++++++++++++++++++++++++++++++++ drivers/mfd/twl6040-irq.c | 205 +++++++++++ include/linux/i2c/twl.h | 1 + include/linux/mfd/twl6040.h | 261 ++++++++++++++ 8 files changed, 1088 insertions(+), 5 deletions(-) create mode 100644 drivers/mfd/twl6040-core.c create mode 100644 drivers/mfd/twl6040-irq.c create mode 100644 include/linux/mfd/twl6040.h
diff --git a/arch/arm/plat-omap/include/plat/irqs.h b/arch/arm/plat-omap/include/plat/irqs.h index 5a25098..2cfba51 100644 --- a/arch/arm/plat-omap/include/plat/irqs.h +++ b/arch/arm/plat-omap/include/plat/irqs.h @@ -407,11 +407,19 @@ #endif #define TWL6030_IRQ_END (TWL6030_IRQ_BASE + TWL6030_BASE_NR_IRQS)
+#define TWL6040_CODEC_IRQ_BASE TWL6030_IRQ_END +#ifdef CONFIG_TWL6040_CODEC +#define TWL6040_CODEC_NR_IRQS 6 +#else +#define TWL6040_CODEC_NR_IRQS 0 +#endif +#define TWL6040_CODEC_IRQ_END (TWL6040_CODEC_IRQ_BASE + TWL6040_CODEC_NR_IRQS) + /* Total number of interrupts depends on the enabled blocks above */ -#if (TWL4030_GPIO_IRQ_END > TWL6030_IRQ_END) +#if (TWL4030_GPIO_IRQ_END > TWL6040_CODEC_IRQ_END) #define TWL_IRQ_END TWL4030_GPIO_IRQ_END #else -#define TWL_IRQ_END TWL6030_IRQ_END +#define TWL_IRQ_END TWL6040_CODEC_IRQ_END #endif
/* GPMC related */ diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 30f3536..169df9f 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -255,6 +255,12 @@ config TWL6030_PWM Say yes here if you want support for TWL6030 PWM. This is used to control charging LED brightness.
+config TWL6040_CORE + bool + depends on TWL4030_CORE && GENERIC_HARDIRQS + select MFD_CORE + default n + config MFD_STMPE bool "Support STMicroelectronics STMPE" depends on I2C=y && GENERIC_HARDIRQS diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 77cb99a..eda1340 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -47,6 +47,7 @@ obj-$(CONFIG_TWL4030_MADC) += twl4030-madc.o obj-$(CONFIG_TWL4030_POWER) += twl4030-power.o obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o obj-$(CONFIG_TWL6030_PWM) += twl6030-pwm.o +obj-$(CONFIG_TWL6040_CORE) += twl6040-core.o twl6040-irq.o
obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c index f9d7880..a2eddc7 100644 --- a/drivers/mfd/twl-core.c +++ b/drivers/mfd/twl-core.c @@ -110,7 +110,7 @@ #endif
#if defined(CONFIG_TWL4030_CODEC) || defined(CONFIG_TWL4030_CODEC_MODULE) ||\ - defined(CONFIG_SND_SOC_TWL6040) || defined(CONFIG_SND_SOC_TWL6040_MODULE) + defined(CONFIG_TWL6040_CORE) || defined(CONFIG_TWL6040_CORE_MODULE) #define twl_has_codec() true #else #define twl_has_codec() false @@ -824,10 +824,9 @@ add_children(struct twl4030_platform_data *pdata, unsigned long features) return PTR_ERR(child); }
- /* Phoenix codec driver is probed directly atm */ if (twl_has_codec() && pdata->audio && twl_class_is_6030()) { sub_chip_id = twl_map[TWL_MODULE_AUDIO_VOICE].sid; - child = add_child(sub_chip_id, "twl6040-codec", + child = add_child(sub_chip_id, "twl6040", pdata->audio, sizeof(*pdata->audio), false, 0, 0); if (IS_ERR(child)) diff --git a/drivers/mfd/twl6040-core.c b/drivers/mfd/twl6040-core.c new file mode 100644 index 0000000..195613c --- /dev/null +++ b/drivers/mfd/twl6040-core.c @@ -0,0 +1,602 @@ +/* + * MFD driver for TWL6040 audio device + * + * Authors: Misael Lopez Cruz misael.lopez@ti.com + * Jorge Eduardo Candelaria jorge.candelaria@ti.com + * Peter Ujfalusi peter.ujfalusi@ti.com + * + * Copyright: (C) 2011 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#include <linux/module.h> +#include <linux/types.h> +#include <linux/slab.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/delay.h> +#include <linux/i2c/twl.h> +#include <linux/mfd/core.h> +#include <linux/mfd/twl6040.h> + +static struct platform_device *twl6040_dev; + +int twl6040_reg_read(struct twl6040 *twl6040, unsigned int reg) +{ + int ret; + u8 val = 0; + + mutex_lock(&twl6040->io_mutex); + ret = twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &val, reg); + if (ret < 0) { + mutex_unlock(&twl6040->io_mutex); + return ret; + } + mutex_unlock(&twl6040->io_mutex); + + return val; +} +EXPORT_SYMBOL(twl6040_reg_read); + +int twl6040_reg_write(struct twl6040 *twl6040, unsigned int reg, u8 val) +{ + int ret; + + mutex_lock(&twl6040->io_mutex); + ret = twl_i2c_write_u8(TWL_MODULE_AUDIO_VOICE, val, reg); + mutex_unlock(&twl6040->io_mutex); + + return ret; +} +EXPORT_SYMBOL(twl6040_reg_write); + +int twl6040_set_bits(struct twl6040 *twl6040, unsigned int reg, u8 mask) +{ + int ret; + u8 val; + + mutex_lock(&twl6040->io_mutex); + ret = twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &val, reg); + if (ret) + goto out; + + val |= mask; + ret = twl_i2c_write_u8(TWL_MODULE_AUDIO_VOICE, val, reg); +out: + mutex_unlock(&twl6040->io_mutex); + return ret; +} +EXPORT_SYMBOL(twl6040_set_bits); + +int twl6040_clear_bits(struct twl6040 *twl6040, unsigned int reg, u8 mask) +{ + int ret; + u8 val; + + mutex_lock(&twl6040->io_mutex); + ret = twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &val, reg); + if (ret) + goto out; + + val &= ~mask; + ret = twl_i2c_write_u8(TWL_MODULE_AUDIO_VOICE, val, reg); +out: + mutex_unlock(&twl6040->io_mutex); + return ret; +} +EXPORT_SYMBOL(twl6040_clear_bits); + +/* twl6040 codec manual power-up sequence */ +static int twl6040_power_up(struct twl6040 *twl6040) +{ + u8 ldoctl, ncpctl, lppllctl; + int ret; + + /* enable high-side LDO, reference system and internal oscillator */ + ldoctl = TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA; + ret = twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); + if (ret) + return ret; + usleep_range(10000, 10500); + + /* enable negative charge pump */ + ncpctl = TWL6040_NCPENA; + ret = twl6040_reg_write(twl6040, TWL6040_REG_NCPCTL, ncpctl); + if (ret) + goto ncp_err; + usleep_range(1000, 1500); + + /* enable low-side LDO */ + ldoctl |= TWL6040_LSLDOENA; + ret = twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); + if (ret) + goto lsldo_err; + usleep_range(1000, 1500); + + /* enable low-power PLL */ + lppllctl = TWL6040_LPLLENA; + ret = twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); + if (ret) + goto lppll_err; + usleep_range(5000, 5500); + + /* disable internal oscillator */ + ldoctl &= ~TWL6040_OSCENA; + ret = twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); + if (ret) + goto osc_err; + + return 0; + +osc_err: + lppllctl &= ~TWL6040_LPLLENA; + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); +lppll_err: + ldoctl &= ~TWL6040_LSLDOENA; + twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); +lsldo_err: + ncpctl &= ~TWL6040_NCPENA; + twl6040_reg_write(twl6040, TWL6040_REG_NCPCTL, ncpctl); +ncp_err: + ldoctl &= ~(TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA); + twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); + + return ret; +} + +/* twl6040 manual power-down sequence */ +static void twl6040_power_down(struct twl6040 *twl6040) +{ + u8 ncpctl, ldoctl, lppllctl; + + ncpctl = twl6040_reg_read(twl6040, TWL6040_REG_NCPCTL); + ldoctl = twl6040_reg_read(twl6040, TWL6040_REG_LDOCTL); + lppllctl = twl6040_reg_read(twl6040, TWL6040_REG_LPPLLCTL); + + /* enable internal oscillator */ + ldoctl |= TWL6040_OSCENA; + twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); + usleep_range(1000, 1500); + + /* disable low-power PLL */ + lppllctl &= ~TWL6040_LPLLENA; + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); + + /* disable low-side LDO */ + ldoctl &= ~TWL6040_LSLDOENA; + twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); + + /* disable negative charge pump */ + ncpctl &= ~TWL6040_NCPENA; + twl6040_reg_write(twl6040, TWL6040_REG_NCPCTL, ncpctl); + + /* disable high-side LDO, reference system and internal oscillator */ + ldoctl &= ~(TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA); + twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); +} + +static irqreturn_t twl6040_naudint_handler(int irq, void *data) +{ + struct twl6040 *twl6040 = data; + u8 intid, status; + + intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID); + + if (intid & TWL6040_READYINT) + complete(&twl6040->ready); + + if (intid & TWL6040_THINT) { + status = twl6040_reg_read(twl6040, TWL6040_REG_STATUS); + if (status & TWL6040_TSHUTDET) { + dev_warn(&twl6040_dev->dev, + "Thermal shutdown, powering-off"); + twl6040_power(twl6040, 0); + } else { + dev_warn(&twl6040_dev->dev, + "Leaving thermal shutdown, powering-on"); + twl6040_power(twl6040, 1); + } + } + + return IRQ_HANDLED; +} + +static int twl6040_power_up_completion(struct twl6040 *twl6040, + int naudint) +{ + int time_left; + u8 intid; + + time_left = wait_for_completion_timeout(&twl6040->ready, + msecs_to_jiffies(144)); + if (!time_left) { + intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID); + if (!(intid & TWL6040_READYINT)) { + dev_err(&twl6040_dev->dev, + "timeout waiting for READYINT\n"); + return -ETIMEDOUT; + } + } + + return 0; +} + +int twl6040_power(struct twl6040 *twl6040, int on) +{ + int audpwron = twl6040->audpwron; + int naudint = twl6040->irq; + int ret = 0; + + mutex_lock(&twl6040->mutex); + + if (on) { + /* already powered-up */ + if (twl6040->power_count++) + goto out; + + if (gpio_is_valid(audpwron)) { + /* use AUDPWRON line */ + gpio_set_value(audpwron, 1); + /* wait for power-up completion */ + ret = twl6040_power_up_completion(twl6040, naudint); + if (ret) { + dev_err(&twl6040_dev->dev, + "automatic power-down failed\n"); + twl6040->power_count = 0; + goto out; + } + } else { + /* use manual power-up sequence */ + ret = twl6040_power_up(twl6040); + if (ret) { + dev_err(&twl6040_dev->dev, + "manual power-up failed\n"); + twl6040->power_count = 0; + goto out; + } + } + twl6040->pll = TWL6040_LPPLL_ID; + twl6040->sysclk = 19200000; + } else { + /* already powered-down */ + if (!twl6040->power_count) { + dev_err(&twl6040_dev->dev, + "device is already powered-off\n"); + ret = -EPERM; + goto out; + } + + if (--twl6040->power_count) + goto out; + + if (gpio_is_valid(audpwron)) { + /* use AUDPWRON line */ + gpio_set_value(audpwron, 0); + + /* power-down sequence latency */ + usleep_range(500, 700); + } else { + /* use manual power-down sequence */ + twl6040_power_down(twl6040); + } + twl6040->pll = TWL6040_NOPLL_ID; + twl6040->sysclk = 0; + } + +out: + mutex_unlock(&twl6040->mutex); + return ret; +} +EXPORT_SYMBOL(twl6040_power); + +int twl6040_is_powered(struct twl6040 *twl6040) +{ + return twl6040->power_count; +} +EXPORT_SYMBOL(twl6040_is_powered); + +int twl6040_set_pll(struct twl6040 *twl6040, enum twl6040_pll_id id, + unsigned int freq_in, unsigned int freq_out) +{ + u8 hppllctl, lppllctl; + int ret = 0; + + mutex_lock(&twl6040->mutex); + + hppllctl = twl6040_reg_read(twl6040, TWL6040_REG_HPPLLCTL); + lppllctl = twl6040_reg_read(twl6040, TWL6040_REG_LPPLLCTL); + + switch (id) { + case TWL6040_LPPLL_ID: + /* low-power PLL divider */ + switch (freq_out) { + case 17640000: + lppllctl |= TWL6040_LPLLFIN; + break; + case 19200000: + lppllctl &= ~TWL6040_LPLLFIN; + break; + default: + dev_err(&twl6040_dev->dev, + "freq_out %d not supported\n", freq_out); + ret = -EINVAL; + goto pll_out; + } + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); + + switch (freq_in) { + case 32768: + lppllctl |= TWL6040_LPLLENA; + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, + lppllctl); + mdelay(5); + lppllctl &= ~TWL6040_HPLLSEL; + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, + lppllctl); + hppllctl &= ~TWL6040_HPLLENA; + twl6040_reg_write(twl6040, TWL6040_REG_HPPLLCTL, + hppllctl); + break; + default: + dev_err(&twl6040_dev->dev, + "freq_in %d not supported\n", freq_in); + ret = -EINVAL; + goto pll_out; + } + + twl6040->pll = TWL6040_LPPLL_ID; + break; + case TWL6040_HPPLL_ID: + /* high-performance PLL can provide only 19.2 MHz */ + if (freq_out != 19200000) { + dev_err(&twl6040_dev->dev, + "freq_out %d not supported\n", freq_out); + ret = -EINVAL; + goto pll_out; + } + + hppllctl &= ~TWL6040_MCLK_MSK; + + switch (freq_in) { + case 12000000: + /* PLL enabled, active mode */ + hppllctl |= TWL6040_MCLK_12000KHZ | + TWL6040_HPLLENA; + break; + case 19200000: + /* + * PLL disabled + * (enable PLL if MCLK jitter quality + * doesn't meet specification) + */ + hppllctl |= TWL6040_MCLK_19200KHZ; + break; + case 26000000: + /* PLL enabled, active mode */ + hppllctl |= TWL6040_MCLK_26000KHZ | + TWL6040_HPLLENA; + break; + case 38400000: + /* PLL enabled, active mode */ + hppllctl |= TWL6040_MCLK_38400KHZ | + TWL6040_HPLLENA; + break; + default: + dev_err(&twl6040_dev->dev, + "freq_in %d not supported\n", freq_in); + ret = -EINVAL; + goto pll_out; + } + + /* enable clock slicer to ensure input waveform is square */ + hppllctl |= TWL6040_HPLLSQRENA; + + twl6040_reg_write(twl6040, TWL6040_REG_HPPLLCTL, hppllctl); + usleep_range(500, 700); + lppllctl |= TWL6040_HPLLSEL; + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); + lppllctl &= ~TWL6040_LPLLENA; + twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); + + twl6040->pll = TWL6040_HPPLL_ID; + break; + default: + dev_err(&twl6040_dev->dev, "unknown pll id %d\n", id); + ret = -EINVAL; + goto pll_out; + } + + twl6040->sysclk = freq_out; + +pll_out: + mutex_unlock(&twl6040->mutex); + return ret; +} +EXPORT_SYMBOL(twl6040_set_pll); + +enum twl6040_pll_id twl6040_get_pll(struct twl6040 *twl6040) +{ + return twl6040->pll; +} +EXPORT_SYMBOL(twl6040_get_pll); + +unsigned int twl6040_get_sysclk(struct twl6040 *twl6040) +{ + return twl6040->sysclk; +} +EXPORT_SYMBOL(twl6040_get_sysclk); + +static int __devinit twl6040_probe(struct platform_device *pdev) +{ + struct twl4030_audio_data *pdata = pdev->dev.platform_data; + struct twl6040 *twl6040; + struct mfd_cell *cell = NULL; + int ret, children = 0; + + if (!pdata) { + dev_err(&pdev->dev, "Platform data is missing\n"); + return -EINVAL; + } + + twl6040 = kzalloc(sizeof(struct twl6040), GFP_KERNEL); + if (!twl6040) + return -ENOMEM; + + platform_set_drvdata(pdev, twl6040); + + twl6040_dev = pdev; + twl6040->dev = &pdev->dev; + twl6040->audpwron = pdata->audpwron_gpio; + twl6040->irq = pdata->naudint_irq; + twl6040->irq_base = pdata->irq_base; + + mutex_init(&twl6040->mutex); + mutex_init(&twl6040->io_mutex); + init_completion(&twl6040->ready); + + twl6040->rev = twl6040_reg_read(twl6040, TWL6040_REG_ASICREV); + + if (gpio_is_valid(twl6040->audpwron)) { + ret = gpio_request(twl6040->audpwron, "audpwron"); + if (ret) + goto gpio1_err; + + ret = gpio_direction_output(twl6040->audpwron, 0); + if (ret) + goto gpio2_err; + } + + /* ERRATA: Automatic power-up is not possible in ES1.0 */ + if (twl6040_get_rev(twl6040) == TWL6040_REV_ES1_0) + twl6040->audpwron = -EINVAL; + + if (twl6040->irq) { + /* codec interrupt */ + ret = twl6040_irq_init(twl6040); + if (ret) + goto gpio2_err; + + ret = twl6040_request_irq(twl6040, TWL6040_IRQ_READY, + twl6040_naudint_handler, 0, + "twl6040_irq_ready", twl6040); + if (ret) { + dev_err(twl6040->dev, "READY IRQ request failed: %d\n", + ret); + goto irq_err; + } + } + + /* dual-access registers controlled by I2C only */ + twl6040_set_bits(twl6040, TWL6040_REG_ACCCTL, TWL6040_I2CSEL); + + if (pdata->codec) { + cell = &twl6040->cells[children]; + cell->name = "twl6040-codec"; + /* The codec expects the twl4030_audio_data as platform data */ + cell->platform_data = pdata; + cell->pdata_size = sizeof(*pdata); + children++; + } + + if (pdata->vibra) { + cell = &twl6040->cells[children]; + cell->name = "twl6040-vibra"; + cell->platform_data = pdata->vibra; + cell->pdata_size = sizeof(*pdata->vibra); + children++; + } + + if (children) { + ret = mfd_add_devices(&pdev->dev, pdev->id, twl6040->cells, + children, NULL, 0); + if (ret) + goto mfd_err; + } else { + dev_err(&pdev->dev, "No platform data found for children\n"); + ret = -ENODEV; + goto mfd_err; + } + + return 0; + +mfd_err: + if (twl6040->irq) + twl6040_free_irq(twl6040, TWL6040_IRQ_READY, twl6040); +irq_err: + if (twl6040->irq) + twl6040_irq_exit(twl6040); +gpio2_err: + if (gpio_is_valid(twl6040->audpwron)) + gpio_free(twl6040->audpwron); +gpio1_err: + platform_set_drvdata(pdev, NULL); + kfree(twl6040); + twl6040_dev = NULL; + return ret; +} + +static int __devexit twl6040_remove(struct platform_device *pdev) +{ + struct twl6040 *twl6040 = platform_get_drvdata(pdev); + + if (twl6040_is_powered(twl6040)) + twl6040_power(twl6040, 0); + + if (gpio_is_valid(twl6040->audpwron)) + gpio_free(twl6040->audpwron); + + twl6040_free_irq(twl6040, TWL6040_IRQ_READY, twl6040); + + if (twl6040->irq) + twl6040_irq_exit(twl6040); + + mfd_remove_devices(&pdev->dev); + platform_set_drvdata(pdev, NULL); + kfree(twl6040); + twl6040_dev = NULL; + + return 0; +} + +static struct platform_driver twl6040_driver = { + .probe = twl6040_probe, + .remove = __devexit_p(twl6040_remove), + .driver = { + .owner = THIS_MODULE, + .name = "twl6040", + }, +}; + +static int __devinit twl6040_init(void) +{ + return platform_driver_register(&twl6040_driver); +} +module_init(twl6040_init); + +static void __devexit twl6040_exit(void) +{ + platform_driver_unregister(&twl6040_driver); +} + +module_exit(twl6040_exit); + +MODULE_DESCRIPTION("TWL6040 MFD"); +MODULE_AUTHOR("Misael Lopez Cruz misael.lopez@ti.com"); +MODULE_AUTHOR("Jorge Eduardo Candelaria jorge.candelaria@ti.com"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:twl6040"); diff --git a/drivers/mfd/twl6040-irq.c b/drivers/mfd/twl6040-irq.c new file mode 100644 index 0000000..9380535 --- /dev/null +++ b/drivers/mfd/twl6040-irq.c @@ -0,0 +1,205 @@ +/* + * Interrupt controller support for TWL6040 + * + * Author: Misael Lopez Cruz misael.lopez@ti.com + * + * Copyright: (C) 2011 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/irq.h> +#include <linux/interrupt.h> +#include <linux/mfd/core.h> +#include <linux/mfd/twl6040.h> + +struct twl6040_irq_data { + int mask; + int status; +}; + +static struct twl6040_irq_data twl6040_irqs[] = { + { + .mask = TWL6040_THMSK, + .status = TWL6040_THINT, + }, + { + .mask = TWL6040_PLUGMSK, + .status = TWL6040_PLUGINT | TWL6040_UNPLUGINT, + }, + { + .mask = TWL6040_HOOKMSK, + .status = TWL6040_HOOKINT, + }, + { + .mask = TWL6040_HFMSK, + .status = TWL6040_HFINT, + }, + { + .mask = TWL6040_VIBMSK, + .status = TWL6040_VIBINT, + }, + { + .mask = TWL6040_READYMSK, + .status = TWL6040_READYINT, + }, +}; + +static inline +struct twl6040_irq_data *irq_to_twl6040_irq(struct twl6040 *twl6040, + int irq) +{ + return &twl6040_irqs[irq - twl6040->irq_base]; +} + +static void twl6040_irq_lock(struct irq_data *data) +{ + struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data); + + mutex_lock(&twl6040->irq_mutex); +} + +static void twl6040_irq_sync_unlock(struct irq_data *data) +{ + struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data); + + /* write back to hardware any change in irq mask */ + if (twl6040->irq_masks_cur != twl6040->irq_masks_cache) { + twl6040->irq_masks_cache = twl6040->irq_masks_cur; + twl6040_reg_write(twl6040, TWL6040_REG_INTMR, + twl6040->irq_masks_cur); + } + + mutex_unlock(&twl6040->irq_mutex); +} + +static void twl6040_irq_enable(struct irq_data *data) +{ + struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data); + struct twl6040_irq_data *irq_data = irq_to_twl6040_irq(twl6040, + data->irq); + + twl6040->irq_masks_cur &= ~irq_data->mask; +} + +static void twl6040_irq_disable(struct irq_data *data) +{ + struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data); + struct twl6040_irq_data *irq_data = irq_to_twl6040_irq(twl6040, + data->irq); + + twl6040->irq_masks_cur |= irq_data->mask; +} + +static struct irq_chip twl6040_irq_chip = { + .name = "twl6040", + .irq_bus_lock = twl6040_irq_lock, + .irq_bus_sync_unlock = twl6040_irq_sync_unlock, + .irq_enable = twl6040_irq_enable, + .irq_disable = twl6040_irq_disable, +}; + +static irqreturn_t twl6040_irq_thread(int irq, void *data) +{ + struct twl6040 *twl6040 = data; + u8 intid; + int i; + + intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID); + + /* apply masking and report (backwards to handle READYINT first) */ + for (i = ARRAY_SIZE(twl6040_irqs) - 1; i >= 0; i--) { + if (twl6040->irq_masks_cur & twl6040_irqs[i].mask) + intid &= ~twl6040_irqs[i].status; + if (intid & twl6040_irqs[i].status) + handle_nested_irq(twl6040->irq_base + i); + } + + /* ack unmasked irqs */ + twl6040_reg_write(twl6040, TWL6040_REG_INTID, intid); + + return IRQ_HANDLED; +} + +int twl6040_irq_init(struct twl6040 *twl6040) +{ + int cur_irq, ret; + u8 val; + + mutex_init(&twl6040->irq_mutex); + + /* mask the individual interrupt sources */ + twl6040->irq_masks_cur = TWL6040_ALLINT_MSK; + twl6040->irq_masks_cache = TWL6040_ALLINT_MSK; + twl6040_reg_write(twl6040, TWL6040_REG_INTMR, TWL6040_ALLINT_MSK); + + if (!twl6040->irq) { + dev_warn(twl6040->dev, + "no interrupt specified, no interrupts\n"); + twl6040->irq_base = 0; + return 0; + } + + if (!twl6040->irq_base) { + dev_err(twl6040->dev, + "no interrupt base specified, no interrupts\n"); + return 0; + } + + /* Register them with genirq */ + for (cur_irq = twl6040->irq_base; + cur_irq < twl6040->irq_base + ARRAY_SIZE(twl6040_irqs); + cur_irq++) { + irq_set_chip_data(cur_irq, twl6040); + irq_set_chip_and_handler(cur_irq, &twl6040_irq_chip, + handle_level_irq); + irq_set_nested_thread(cur_irq, 1); + + /* ARM needs us to explicitly flag the IRQ as valid + * and will set them noprobe when we do so. */ +#ifdef CONFIG_ARM + set_irq_flags(cur_irq, IRQF_VALID); +#else + irq_set_noprobe(cur_irq); +#endif + } + + ret = request_threaded_irq(twl6040->irq, NULL, twl6040_irq_thread, + IRQF_ONESHOT, "twl6040", twl6040); + if (ret) { + dev_err(twl6040->dev, "failed to request IRQ %d: %d\n", + twl6040->irq, ret); + return ret; + } + + /* reset interrupts */ + val = twl6040_reg_read(twl6040, TWL6040_REG_INTID); + + /* interrupts cleared on write */ + twl6040_clear_bits(twl6040, TWL6040_REG_ACCCTL, TWL6040_INTCLRMODE); + + return 0; +} +EXPORT_SYMBOL(twl6040_irq_init); + +void twl6040_irq_exit(struct twl6040 *twl6040) +{ + if (twl6040->irq) + free_irq(twl6040->irq, twl6040); +} +EXPORT_SYMBOL(twl6040_irq_exit); diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index e0aba2b..ea5baa2 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -679,6 +679,7 @@ struct twl4030_audio_data { /* twl6040 */ int audpwron_gpio; /* audio power-on gpio */ int naudint_irq; /* audio interrupt */ + unsigned int irq_base; };
struct twl4030_platform_data { diff --git a/include/linux/mfd/twl6040.h b/include/linux/mfd/twl6040.h new file mode 100644 index 0000000..d384a01 --- /dev/null +++ b/include/linux/mfd/twl6040.h @@ -0,0 +1,261 @@ +/* + * MFD driver for twl6040 + * + * Authors: Jorge Eduardo Candelaria jorge.candelaria@ti.com + * Misael Lopez Cruz misael.lopez@ti.com + * + * Copyright: (C) 2011 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ + +#ifndef __TWL6040_CODEC_H__ +#define __TWL6040_CODEC_H__ + +#include <linux/interrupt.h> +#include <linux/mfd/core.h> + +#define TWL6040_REG_ASICID 0x01 +#define TWL6040_REG_ASICREV 0x02 +#define TWL6040_REG_INTID 0x03 +#define TWL6040_REG_INTMR 0x04 +#define TWL6040_REG_NCPCTL 0x05 +#define TWL6040_REG_LDOCTL 0x06 +#define TWL6040_REG_HPPLLCTL 0x07 +#define TWL6040_REG_LPPLLCTL 0x08 +#define TWL6040_REG_LPPLLDIV 0x09 +#define TWL6040_REG_AMICBCTL 0x0A +#define TWL6040_REG_DMICBCTL 0x0B +#define TWL6040_REG_MICLCTL 0x0C +#define TWL6040_REG_MICRCTL 0x0D +#define TWL6040_REG_MICGAIN 0x0E +#define TWL6040_REG_LINEGAIN 0x0F +#define TWL6040_REG_HSLCTL 0x10 +#define TWL6040_REG_HSRCTL 0x11 +#define TWL6040_REG_HSGAIN 0x12 +#define TWL6040_REG_EARCTL 0x13 +#define TWL6040_REG_HFLCTL 0x14 +#define TWL6040_REG_HFLGAIN 0x15 +#define TWL6040_REG_HFRCTL 0x16 +#define TWL6040_REG_HFRGAIN 0x17 +#define TWL6040_REG_VIBCTLL 0x18 +#define TWL6040_REG_VIBDATL 0x19 +#define TWL6040_REG_VIBCTLR 0x1A +#define TWL6040_REG_VIBDATR 0x1B +#define TWL6040_REG_HKCTL1 0x1C +#define TWL6040_REG_HKCTL2 0x1D +#define TWL6040_REG_GPOCTL 0x1E +#define TWL6040_REG_ALB 0x1F +#define TWL6040_REG_DLB 0x20 +#define TWL6040_REG_TRIM1 0x28 +#define TWL6040_REG_TRIM2 0x29 +#define TWL6040_REG_TRIM3 0x2A +#define TWL6040_REG_HSOTRIM 0x2B +#define TWL6040_REG_HFOTRIM 0x2C +#define TWL6040_REG_ACCCTL 0x2D +#define TWL6040_REG_STATUS 0x2E + +#define TWL6040_CACHEREGNUM (TWL6040_REG_STATUS + 1) + +#define TWL6040_VIOREGNUM 18 +#define TWL6040_VDDREGNUM 21 + +/* INTID (0x03) fields */ + +#define TWL6040_THINT 0x01 +#define TWL6040_PLUGINT 0x02 +#define TWL6040_UNPLUGINT 0x04 +#define TWL6040_HOOKINT 0x08 +#define TWL6040_HFINT 0x10 +#define TWL6040_VIBINT 0x20 +#define TWL6040_READYINT 0x40 + +/* INTMR (0x04) fields */ + +#define TWL6040_THMSK 0x01 +#define TWL6040_PLUGMSK 0x02 +#define TWL6040_HOOKMSK 0x08 +#define TWL6040_HFMSK 0x10 +#define TWL6040_VIBMSK 0x20 +#define TWL6040_READYMSK 0x40 +#define TWL6040_ALLINT_MSK 0x7B + +/* NCPCTL (0x05) fields */ + +#define TWL6040_NCPENA 0x01 +#define TWL6040_NCPOPEN 0x40 + +/* LDOCTL (0x06) fields */ + +#define TWL6040_LSLDOENA 0x01 +#define TWL6040_HSLDOENA 0x04 +#define TWL6040_REFENA 0x40 +#define TWL6040_OSCENA 0x80 + +/* HPPLLCTL (0x07) fields */ + +#define TWL6040_HPLLENA 0x01 +#define TWL6040_HPLLRST 0x02 +#define TWL6040_HPLLBP 0x04 +#define TWL6040_HPLLSQRENA 0x08 +#define TWL6040_MCLK_12000KHZ (0 << 5) +#define TWL6040_MCLK_19200KHZ (1 << 5) +#define TWL6040_MCLK_26000KHZ (2 << 5) +#define TWL6040_MCLK_38400KHZ (3 << 5) +#define TWL6040_MCLK_MSK 0x60 + +/* LPPLLCTL (0x08) fields */ + +#define TWL6040_LPLLENA 0x01 +#define TWL6040_LPLLRST 0x02 +#define TWL6040_LPLLSEL 0x04 +#define TWL6040_LPLLFIN 0x08 +#define TWL6040_HPLLSEL 0x10 + +/* HSLCTL (0x10) fields */ + +#define TWL6040_HSDACMODEL 0x02 +#define TWL6040_HSDRVMODEL 0x08 + +/* HSRCTL (0x11) fields */ + +#define TWL6040_HSDACMODER 0x02 +#define TWL6040_HSDRVMODER 0x08 + +/* VIBCTLL (0x18) fields */ + +#define TWL6040_VIBENAL 0x01 +#define TWL6040_VIBCTRLL 0x04 +#define TWL6040_VIBCTRLLP 0x08 +#define TWL6040_VIBCTRLLN 0x10 + +/* VIBDATL (0x19) fields */ + +#define TWL6040_VIBDAT_MAX 0x64 + +/* VIBCTLR (0x1A) fields */ + +#define TWL6040_VIBENAR 0x01 +#define TWL6040_VIBCTRLR 0x04 +#define TWL6040_VIBCTRLRP 0x08 +#define TWL6040_VIBCTRLRN 0x10 + +/* GPOCTL (0x1E) fields */ + +#define TWL6040_GPO1 0x01 +#define TWL6040_GPO2 0x02 +#define TWL6040_GPO3 0x03 + +/* ACCCTL (0x2D) fields */ + +#define TWL6040_I2CSEL 0x01 +#define TWL6040_RESETSPLIT 0x04 +#define TWL6040_INTCLRMODE 0x08 + +#define TWL6040_SYSCLK_SEL_LPPLL 1 +#define TWL6040_SYSCLK_SEL_HPPLL 2 + +/* STATUS (0x2E) fields */ + +#define TWL6040_PLUGCOMP 0x02 +#define TWL6040_VIBLOCDET 0x10 +#define TWL6040_VIBROCDET 0x20 +#define TWL6040_TSHUTDET 0x40 + +#define TWL6040_CELLS 2 + +#define TWL6040_REV_ES1_0 0x00 +#define TWL6040_REV_ES1_1 0x01 +#define TWL6040_REV_ES1_2 0x02 + +#define TWL6040_IRQ_TH 0 +#define TWL6040_IRQ_PLUG 1 +#define TWL6040_IRQ_HOOK 2 +#define TWL6040_IRQ_HF 3 +#define TWL6040_IRQ_VIB 4 +#define TWL6040_IRQ_READY 5 + +enum twl6040_pll_id { + TWL6040_NOPLL_ID, + TWL6040_LPPLL_ID, + TWL6040_HPPLL_ID, +}; + +struct twl6040 { + struct device *dev; + struct mutex mutex; + struct mutex io_mutex; + struct mutex irq_mutex; + struct mfd_cell cells[TWL6040_CELLS]; + struct completion ready; + + int audpwron; + int power_count; + int rev; + + enum twl6040_pll_id pll; + unsigned int sysclk; + + unsigned int irq; + unsigned int irq_base; + u8 irq_masks_cur; + u8 irq_masks_cache; +}; + +static inline int twl6040_get_rev(struct twl6040 *twl6040) +{ + return twl6040->rev; +} + +static inline int twl6040_request_irq(struct twl6040 *twl6040, int irq, + irq_handler_t handler, + unsigned long irqflags, + const char *name, + void *data) +{ + if (!twl6040->irq_base) + return -EINVAL; + + return request_threaded_irq(twl6040->irq_base + irq, NULL, handler, + irqflags, name, data); +} + +static inline void twl6040_free_irq(struct twl6040 *twl6040, int irq, + void *data) +{ + if (!twl6040->irq_base) + return; + + free_irq(twl6040->irq_base + irq, data); +} + +int twl6040_reg_read(struct twl6040 *twl6040, unsigned int reg); +int twl6040_reg_write(struct twl6040 *twl6040, unsigned int reg, + u8 val); +int twl6040_set_bits(struct twl6040 *twl6040, unsigned int reg, + u8 mask); +int twl6040_clear_bits(struct twl6040 *twl6040, unsigned int reg, + u8 mask); +int twl6040_power(struct twl6040 *twl6040, int on); +int twl6040_is_powered(struct twl6040 *twl6040); +int twl6040_set_pll(struct twl6040 *twl6040, enum twl6040_pll_id id, + unsigned int freq_in, unsigned int freq_out); +enum twl6040_pll_id twl6040_get_pll(struct twl6040 *twl6040); +unsigned int twl6040_get_sysclk(struct twl6040 *twl6040); +int twl6040_irq_init(struct twl6040 *twl6040); +void twl6040_irq_exit(struct twl6040 *twl6040); + +#endif /* End of __TWL6040_CODEC_H__ */
From: Misael Lopez Cruz misael.lopez@ti.com
Convert TWL6040 CODEC driver into a TWL6040 MFD child, it implies that MFD-level operations like register accesses, clock setting and power management are done through MFD APIs, not directly by CODEC driver anymore. To avoid conflicts with the other MFD child, vibrator registers are skipped in CODEC driver.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com --- sound/soc/codecs/Kconfig | 1 + sound/soc/codecs/twl6040.c | 425 +++++++++----------------------------------- sound/soc/codecs/twl6040.h | 118 ------------ sound/soc/omap/sdp4430.c | 2 + 4 files changed, 90 insertions(+), 456 deletions(-)
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 0002220..922f59f 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -240,6 +240,7 @@ config SND_SOC_TWL4030 tristate
config SND_SOC_TWL6040 + select TWL6040_CORE tristate
config SND_SOC_UDA134X diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index ade6616..a20e293 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -24,11 +24,10 @@ #include <linux/init.h> #include <linux/delay.h> #include <linux/pm.h> -#include <linux/i2c.h> -#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/i2c/twl.h> +#include <linux/mfd/twl6040.h>
#include <sound/core.h> #include <sound/pcm.h> @@ -77,14 +76,12 @@ struct twl6040_jack_data {
/* codec private data */ struct twl6040_data { - int audpwron; - int naudint; int codec_powered; int pll; int non_lp; + unsigned int clk_in; unsigned int sysclk; struct snd_pcm_hw_constraint_list *sysclk_constraints; - struct completion ready; struct twl6040_jack_data hs_jack; struct snd_soc_codec *codec; struct workqueue_struct *workqueue; @@ -239,12 +236,13 @@ static inline void twl6040_write_reg_cache(struct snd_soc_codec *codec, static int twl6040_read_reg_volatile(struct snd_soc_codec *codec, unsigned int reg) { + struct twl6040 *twl6040 = codec->control_data; u8 value;
if (reg >= TWL6040_CACHEREGNUM) return -EIO;
- twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &value, reg); + value = twl6040_reg_read(twl6040, reg); twl6040_write_reg_cache(codec, reg, value);
return value; @@ -256,11 +254,13 @@ static int twl6040_read_reg_volatile(struct snd_soc_codec *codec, static int twl6040_write(struct snd_soc_codec *codec, unsigned int reg, unsigned int value) { + struct twl6040 *twl6040 = codec->control_data; + if (reg >= TWL6040_CACHEREGNUM) return -EIO;
twl6040_write_reg_cache(codec, reg, value); - return twl_i2c_write_u8(TWL_MODULE_AUDIO_VOICE, value, reg); + return twl6040_reg_write(twl6040, reg, value); }
static void twl6040_init_vio_regs(struct snd_soc_codec *codec) @@ -268,15 +268,21 @@ static void twl6040_init_vio_regs(struct snd_soc_codec *codec) u8 *cache = codec->reg_cache; int reg, i;
- /* allow registers to be accessed by i2c */ - twl6040_write(codec, TWL6040_REG_ACCCTL, cache[TWL6040_REG_ACCCTL]); - for (i = 0; i < TWL6040_VIOREGNUM; i++) { reg = twl6040_vio_reg[i]; - /* skip read-only registers (ASICID, ASICREV, STATUS) */ + /* + * skip read-only registers (ASICID, ASICREV, STATUS) + * and registers shared among MFD children + */ switch (reg) { case TWL6040_REG_ASICID: case TWL6040_REG_ASICREV: + case TWL6040_REG_INTID: + case TWL6040_REG_INTMR: + case TWL6040_REG_NCPCTL: + case TWL6040_REG_LDOCTL: + case TWL6040_REG_GPOCTL: + case TWL6040_REG_ACCCTL: case TWL6040_REG_STATUS: continue; default: @@ -293,6 +299,20 @@ static void twl6040_init_vdd_regs(struct snd_soc_codec *codec)
for (i = 0; i < TWL6040_VDDREGNUM; i++) { reg = twl6040_vdd_reg[i]; + /* skip vibra and PLL registers */ + switch (reg) { + case TWL6040_REG_VIBCTLL: + case TWL6040_REG_VIBDATL: + case TWL6040_REG_VIBCTLR: + case TWL6040_REG_VIBDATR: + case TWL6040_REG_HPPLLCTL: + case TWL6040_REG_LPPLLCTL: + case TWL6040_REG_LPPLLDIV: + continue; + default: + break; + } + twl6040_write(codec, reg, cache[reg]); } } @@ -596,88 +616,6 @@ static int pga_event(struct snd_soc_dapm_widget *w, return 0; }
-/* twl6040 codec manual power-up sequence */ -static void twl6040_power_up(struct snd_soc_codec *codec) -{ - u8 ncpctl, ldoctl, lppllctl, accctl; - - ncpctl = twl6040_read_reg_cache(codec, TWL6040_REG_NCPCTL); - ldoctl = twl6040_read_reg_cache(codec, TWL6040_REG_LDOCTL); - lppllctl = twl6040_read_reg_cache(codec, TWL6040_REG_LPPLLCTL); - accctl = twl6040_read_reg_cache(codec, TWL6040_REG_ACCCTL); - - /* enable reference system */ - ldoctl |= TWL6040_REFENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - msleep(10); - /* enable internal oscillator */ - ldoctl |= TWL6040_OSCENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - udelay(10); - /* enable high-side ldo */ - ldoctl |= TWL6040_HSLDOENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - udelay(244); - /* enable negative charge pump */ - ncpctl |= TWL6040_NCPENA | TWL6040_NCPOPEN; - twl6040_write(codec, TWL6040_REG_NCPCTL, ncpctl); - udelay(488); - /* enable low-side ldo */ - ldoctl |= TWL6040_LSLDOENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - udelay(244); - /* enable low-power pll */ - lppllctl |= TWL6040_LPLLENA; - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); - /* reset state machine */ - accctl |= TWL6040_RESETSPLIT; - twl6040_write(codec, TWL6040_REG_ACCCTL, accctl); - mdelay(5); - accctl &= ~TWL6040_RESETSPLIT; - twl6040_write(codec, TWL6040_REG_ACCCTL, accctl); - /* disable internal oscillator */ - ldoctl &= ~TWL6040_OSCENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); -} - -/* twl6040 codec manual power-down sequence */ -static void twl6040_power_down(struct snd_soc_codec *codec) -{ - u8 ncpctl, ldoctl, lppllctl, accctl; - - ncpctl = twl6040_read_reg_cache(codec, TWL6040_REG_NCPCTL); - ldoctl = twl6040_read_reg_cache(codec, TWL6040_REG_LDOCTL); - lppllctl = twl6040_read_reg_cache(codec, TWL6040_REG_LPPLLCTL); - accctl = twl6040_read_reg_cache(codec, TWL6040_REG_ACCCTL); - - /* enable internal oscillator */ - ldoctl |= TWL6040_OSCENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - udelay(10); - /* disable low-power pll */ - lppllctl &= ~TWL6040_LPLLENA; - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); - /* disable low-side ldo */ - ldoctl &= ~TWL6040_LSLDOENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - udelay(244); - /* disable negative charge pump */ - ncpctl &= ~(TWL6040_NCPENA | TWL6040_NCPOPEN); - twl6040_write(codec, TWL6040_REG_NCPCTL, ncpctl); - udelay(488); - /* disable high-side ldo */ - ldoctl &= ~TWL6040_HSLDOENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - udelay(244); - /* disable internal oscillator */ - ldoctl &= ~TWL6040_OSCENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - /* disable reference system */ - ldoctl &= ~TWL6040_REFENA; - twl6040_write(codec, TWL6040_REG_LDOCTL, ldoctl); - msleep(10); -} - /* set headset dac and driver power mode */ static int headset_power_mode(struct snd_soc_codec *codec, int high_perf) { @@ -766,33 +704,19 @@ static void twl6040_accessory_work(struct work_struct *work) }
/* audio interrupt handler */ -static irqreturn_t twl6040_naudint_handler(int irq, void *data) +static irqreturn_t twl6040_audio_handler(int irq, void *data) { struct snd_soc_codec *codec = data; + struct twl6040 *twl6040 = codec->control_data; struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); u8 intid;
- twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &intid, TWL6040_REG_INTID); - - if (intid & TWL6040_THINT) - dev_alert(codec->dev, "die temp over-limit detection\n"); + intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID);
if ((intid & TWL6040_PLUGINT) || (intid & TWL6040_UNPLUGINT)) queue_delayed_work(priv->workqueue, &priv->delayed_work, msecs_to_jiffies(200));
- if (intid & TWL6040_HOOKINT) - dev_info(codec->dev, "hook detection\n"); - - if (intid & TWL6040_HFINT) - dev_alert(codec->dev, "hf drivers over current detection\n"); - - if (intid & TWL6040_VIBINT) - dev_alert(codec->dev, "vib drivers over current detection\n"); - - if (intid & TWL6040_READYINT) - complete(&priv->ready); - return IRQ_HANDLED; }
@@ -1231,36 +1155,11 @@ static int twl6040_add_widgets(struct snd_soc_codec *codec) return 0; }
-static int twl6040_power_up_completion(struct snd_soc_codec *codec, - int naudint) -{ - struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); - int time_left; - u8 intid; - - time_left = wait_for_completion_timeout(&priv->ready, - msecs_to_jiffies(144)); - - if (!time_left) { - twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &intid, - TWL6040_REG_INTID); - if (!(intid & TWL6040_READYINT)) { - dev_err(codec->dev, "timeout waiting for READYINT\n"); - return -ETIMEDOUT; - } - } - - priv->codec_powered = 1; - - return 0; -} - static int twl6040_set_bias_level(struct snd_soc_codec *codec, enum snd_soc_bias_level level) { + struct twl6040 *twl6040 = codec->control_data; struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); - int audpwron = priv->audpwron; - int naudint = priv->naudint; int ret;
switch (level) { @@ -1272,62 +1171,30 @@ static int twl6040_set_bias_level(struct snd_soc_codec *codec, if (priv->codec_powered) break;
- if (gpio_is_valid(audpwron)) { - /* use AUDPWRON line */ - gpio_set_value(audpwron, 1); - - /* wait for power-up completion */ - ret = twl6040_power_up_completion(codec, naudint); - if (ret) - return ret; + ret = twl6040_power(twl6040, 1); + if (ret) + return ret;
- /* sync registers updated during power-up sequence */ - twl6040_read_reg_volatile(codec, TWL6040_REG_NCPCTL); - twl6040_read_reg_volatile(codec, TWL6040_REG_LDOCTL); - twl6040_read_reg_volatile(codec, TWL6040_REG_LPPLLCTL); - } else { - /* use manual power-up sequence */ - twl6040_power_up(codec); - priv->codec_powered = 1; - } + priv->codec_powered = 1;
/* initialize vdd/vss registers with reg_cache */ twl6040_init_vdd_regs(codec);
/* Set external boost GPO */ twl6040_write(codec, TWL6040_REG_GPOCTL, 0x02); - - /* Set initial minimal gain values */ - twl6040_write(codec, TWL6040_REG_HSGAIN, 0xFF); - twl6040_write(codec, TWL6040_REG_EARCTL, 0x1E); - twl6040_write(codec, TWL6040_REG_HFLGAIN, 0x1D); - twl6040_write(codec, TWL6040_REG_HFRGAIN, 0x1D); break; case SND_SOC_BIAS_OFF: if (!priv->codec_powered) break;
- if (gpio_is_valid(audpwron)) { - /* use AUDPWRON line */ - gpio_set_value(audpwron, 0); - - /* power-down sequence latency */ - udelay(500); - - /* sync registers updated during power-down sequence */ - twl6040_read_reg_volatile(codec, TWL6040_REG_NCPCTL); - twl6040_read_reg_volatile(codec, TWL6040_REG_LDOCTL); - twl6040_write_reg_cache(codec, TWL6040_REG_LPPLLCTL, - 0x00); - } else { - /* use manual power-down sequence */ - twl6040_power_down(codec); - } - + twl6040_power(twl6040, 0); priv->codec_powered = 0; break; }
+ /* get PLL and sysclk after power transition */ + priv->pll = twl6040_get_pll(twl6040); + priv->sysclk = twl6040_get_sysclk(twl6040); codec->dapm.bias_level = level;
return 0; @@ -1374,39 +1241,40 @@ static int twl6040_hw_params(struct snd_pcm_substream *substream, { struct snd_soc_pcm_runtime *rtd = substream->private_data; struct snd_soc_codec *codec = rtd->codec; + struct twl6040 *twl6040 = codec->control_data; struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); - u8 lppllctl; - int rate; + unsigned int sysclk; + int rate, ret;
/* nothing to do for high-perf pll, it supports only 48 kHz */ if (priv->pll == TWL6040_HPPLL_ID) return 0;
- lppllctl = twl6040_read_reg_cache(codec, TWL6040_REG_LPPLLCTL); - rate = params_rate(params); switch (rate) { case 11250: case 22500: case 44100: case 88200: - lppllctl |= TWL6040_LPLLFIN; - priv->sysclk = 17640000; + sysclk = 17640000; break; case 8000: case 16000: case 32000: case 48000: case 96000: - lppllctl &= ~TWL6040_LPLLFIN; - priv->sysclk = 19200000; + sysclk = 19200000; break; default: dev_err(codec->dev, "unsupported rate %d\n", rate); return -EINVAL; }
- twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); + ret = twl6040_set_pll(twl6040, TWL6040_LPPLL_ID, priv->clk_in, sysclk); + if (ret) + return ret; + + priv->sysclk = twl6040_get_sysclk(twl6040);
return 0; } @@ -1449,99 +1317,27 @@ static int twl6040_set_dai_sysclk(struct snd_soc_dai *codec_dai, int clk_id, unsigned int freq, int dir) { struct snd_soc_codec *codec = codec_dai->codec; + struct twl6040 *twl6040 = codec->control_data; struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); - u8 hppllctl, lppllctl; - - hppllctl = twl6040_read_reg_cache(codec, TWL6040_REG_HPPLLCTL); - lppllctl = twl6040_read_reg_cache(codec, TWL6040_REG_LPPLLCTL); + int ret = 0;
switch (clk_id) { case TWL6040_SYSCLK_SEL_LPPLL: - switch (freq) { - case 32768: - /* headset dac and driver must be in low-power mode */ - headset_power_mode(codec, 0); - - /* clk32k input requires low-power pll */ - lppllctl |= TWL6040_LPLLENA; - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); - mdelay(5); - lppllctl &= ~TWL6040_HPLLSEL; - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); - hppllctl &= ~TWL6040_HPLLENA; - twl6040_write(codec, TWL6040_REG_HPPLLCTL, hppllctl); - break; - default: - dev_err(codec->dev, "unknown mclk freq %d\n", freq); - return -EINVAL; - } - - /* lppll divider */ - switch (priv->sysclk) { - case 17640000: - lppllctl |= TWL6040_LPLLFIN; - break; - case 19200000: - lppllctl &= ~TWL6040_LPLLFIN; - break; - default: - /* sysclk not yet configured */ - lppllctl &= ~TWL6040_LPLLFIN; - priv->sysclk = 19200000; - break; - } - - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); + ret = twl6040_set_pll(twl6040, TWL6040_LPPLL_ID, + freq, priv->sysclk); + if (ret) + return ret;
- priv->pll = TWL6040_LPPLL_ID; + headset_power_mode(codec, 0); priv->sysclk_constraints = &lp_constraints; break; case TWL6040_SYSCLK_SEL_HPPLL: - hppllctl &= ~TWL6040_MCLK_MSK; - - switch (freq) { - case 12000000: - /* mclk input, pll enabled */ - hppllctl |= TWL6040_MCLK_12000KHZ | - TWL6040_HPLLSQRBP | - TWL6040_HPLLENA; - break; - case 19200000: - /* mclk input, pll disabled */ - hppllctl |= TWL6040_MCLK_19200KHZ | - TWL6040_HPLLSQRENA | - TWL6040_HPLLBP; - break; - case 26000000: - /* mclk input, pll enabled */ - hppllctl |= TWL6040_MCLK_26000KHZ | - TWL6040_HPLLSQRBP | - TWL6040_HPLLENA; - break; - case 38400000: - /* clk slicer, pll disabled */ - hppllctl |= TWL6040_MCLK_38400KHZ | - TWL6040_HPLLSQRENA | - TWL6040_HPLLBP; - break; - default: - dev_err(codec->dev, "unknown mclk freq %d\n", freq); - return -EINVAL; - } + ret = twl6040_set_pll(twl6040, TWL6040_HPPLL_ID, + freq, priv->sysclk); + if (ret) + return ret;
- /* headset dac and driver must be in high-performance mode */ headset_power_mode(codec, 1); - - twl6040_write(codec, TWL6040_REG_HPPLLCTL, hppllctl); - udelay(500); - lppllctl |= TWL6040_HPLLSEL; - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); - lppllctl &= ~TWL6040_LPLLENA; - twl6040_write(codec, TWL6040_REG_LPPLLCTL, lppllctl); - - /* high-performance pll can provide only 19.2 MHz */ - priv->pll = TWL6040_HPPLL_ID; - priv->sysclk = 19200000; priv->sysclk_constraints = &hp_constraints; break; default: @@ -1549,6 +1345,10 @@ static int twl6040_set_dai_sysclk(struct snd_soc_dai *codec_dai, return -EINVAL; }
+ priv->pll = twl6040_get_pll(twl6040); + priv->clk_in = freq; + priv->sysclk = twl6040_get_sysclk(twl6040); + return 0; }
@@ -1600,11 +1400,8 @@ static int twl6040_resume(struct snd_soc_codec *codec)
static int twl6040_probe(struct snd_soc_codec *codec) { - struct twl4030_audio_data *twl_codec = codec->dev->platform_data; struct twl6040_data *priv; - int audpwron, naudint; int ret = 0; - u8 icrev, intmr = TWL6040_ALLINT_MSK;
priv = kzalloc(sizeof(struct twl6040_data), GFP_KERNEL); if (priv == NULL) @@ -1612,23 +1409,9 @@ static int twl6040_probe(struct snd_soc_codec *codec) snd_soc_codec_set_drvdata(codec, priv);
priv->codec = codec; + codec->control_data = dev_get_drvdata(codec->dev->parent);
- twl_i2c_read_u8(TWL_MODULE_AUDIO_VOICE, &icrev, TWL6040_REG_ASICREV); - - if (twl_codec && (icrev > 0)) - audpwron = twl_codec->audpwron_gpio; - else - audpwron = -EINVAL; - - if (twl_codec) - naudint = twl_codec->naudint_irq; - else - naudint = 0; - - priv->audpwron = audpwron; - priv->naudint = naudint; priv->workqueue = create_singlethread_workqueue("twl6040-codec"); - if (!priv->workqueue) { ret = -ENOMEM; goto work_err; @@ -1638,56 +1421,34 @@ static int twl6040_probe(struct snd_soc_codec *codec)
mutex_init(&priv->mutex);
- init_completion(&priv->ready); init_completion(&priv->headset.ramp_done); init_completion(&priv->handsfree.ramp_done);
- if (gpio_is_valid(audpwron)) { - ret = gpio_request(audpwron, "audpwron"); - if (ret) - goto gpio1_err; - - ret = gpio_direction_output(audpwron, 0); - if (ret) - goto gpio2_err; - - priv->codec_powered = 0; - - /* enable only codec ready interrupt */ - intmr &= ~(TWL6040_READYMSK | TWL6040_PLUGMSK); - - /* reset interrupt status to allow correct power up sequence */ - twl6040_read_reg_volatile(codec, TWL6040_REG_INTID); - } - twl6040_write(codec, TWL6040_REG_INTMR, intmr); - - if (naudint) { - /* audio interrupt */ - ret = request_threaded_irq(naudint, NULL, - twl6040_naudint_handler, - IRQF_TRIGGER_LOW | IRQF_ONESHOT, - "twl6040_codec", codec); - if (ret) - goto gpio2_err; - } - - /* init vio registers */ - twl6040_init_vio_regs(codec); - priv->hf_workqueue = create_singlethread_workqueue("twl6040-hf"); if (priv->hf_workqueue == NULL) { ret = -ENOMEM; - goto irq_err; + goto hfwq_err; } priv->hs_workqueue = create_singlethread_workqueue("twl6040-hs"); if (priv->hs_workqueue == NULL) { ret = -ENOMEM; - goto wq_err; + goto hswq_err; }
INIT_DELAYED_WORK(&priv->hs_delayed_work, twl6040_pga_hs_work); INIT_DELAYED_WORK(&priv->hf_delayed_work, twl6040_pga_hf_work);
+ ret = twl6040_request_irq(codec->control_data, TWL6040_IRQ_PLUG, + twl6040_audio_handler, 0, + "twl6040_irq_plug", codec); + if (ret) { + dev_err(codec->dev, "PLUG IRQ request failed: %d\n", ret); + goto plugirq_err; + } + + /* init vio registers */ + twl6040_init_vio_regs(codec); + /* power on device */ ret = twl6040_set_bias_level(codec, SND_SOC_BIAS_STANDBY); if (ret) @@ -1700,16 +1461,12 @@ static int twl6040_probe(struct snd_soc_codec *codec) return 0;
bias_err: + twl6040_free_irq(codec->control_data, TWL6040_IRQ_PLUG, codec); +plugirq_err: destroy_workqueue(priv->hs_workqueue); -wq_err: +hswq_err: destroy_workqueue(priv->hf_workqueue); -irq_err: - if (naudint) - free_irq(naudint, codec); -gpio2_err: - if (gpio_is_valid(audpwron)) - gpio_free(audpwron); -gpio1_err: +hfwq_err: destroy_workqueue(priv->workqueue); work_err: kfree(priv); @@ -1719,17 +1476,9 @@ work_err: static int twl6040_remove(struct snd_soc_codec *codec) { struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); - int audpwron = priv->audpwron; - int naudint = priv->naudint;
twl6040_set_bias_level(codec, SND_SOC_BIAS_OFF); - - if (gpio_is_valid(audpwron)) - gpio_free(audpwron); - - if (naudint) - free_irq(naudint, codec); - + twl6040_free_irq(codec->control_data, TWL6040_IRQ_PLUG, codec); destroy_workqueue(priv->workqueue); destroy_workqueue(priv->hf_workqueue); destroy_workqueue(priv->hs_workqueue); diff --git a/sound/soc/codecs/twl6040.h b/sound/soc/codecs/twl6040.h index 23aeed0..234bfad 100644 --- a/sound/soc/codecs/twl6040.h +++ b/sound/soc/codecs/twl6040.h @@ -22,124 +22,6 @@ #ifndef __TWL6040_H__ #define __TWL6040_H__
-#define TWL6040_REG_ASICID 0x01 -#define TWL6040_REG_ASICREV 0x02 -#define TWL6040_REG_INTID 0x03 -#define TWL6040_REG_INTMR 0x04 -#define TWL6040_REG_NCPCTL 0x05 -#define TWL6040_REG_LDOCTL 0x06 -#define TWL6040_REG_HPPLLCTL 0x07 -#define TWL6040_REG_LPPLLCTL 0x08 -#define TWL6040_REG_LPPLLDIV 0x09 -#define TWL6040_REG_AMICBCTL 0x0A -#define TWL6040_REG_DMICBCTL 0x0B -#define TWL6040_REG_MICLCTL 0x0C -#define TWL6040_REG_MICRCTL 0x0D -#define TWL6040_REG_MICGAIN 0x0E -#define TWL6040_REG_LINEGAIN 0x0F -#define TWL6040_REG_HSLCTL 0x10 -#define TWL6040_REG_HSRCTL 0x11 -#define TWL6040_REG_HSGAIN 0x12 -#define TWL6040_REG_EARCTL 0x13 -#define TWL6040_REG_HFLCTL 0x14 -#define TWL6040_REG_HFLGAIN 0x15 -#define TWL6040_REG_HFRCTL 0x16 -#define TWL6040_REG_HFRGAIN 0x17 -#define TWL6040_REG_VIBCTLL 0x18 -#define TWL6040_REG_VIBDATL 0x19 -#define TWL6040_REG_VIBCTLR 0x1A -#define TWL6040_REG_VIBDATR 0x1B -#define TWL6040_REG_HKCTL1 0x1C -#define TWL6040_REG_HKCTL2 0x1D -#define TWL6040_REG_GPOCTL 0x1E -#define TWL6040_REG_ALB 0x1F -#define TWL6040_REG_DLB 0x20 -#define TWL6040_REG_TRIM1 0x28 -#define TWL6040_REG_TRIM2 0x29 -#define TWL6040_REG_TRIM3 0x2A -#define TWL6040_REG_HSOTRIM 0x2B -#define TWL6040_REG_HFOTRIM 0x2C -#define TWL6040_REG_ACCCTL 0x2D -#define TWL6040_REG_STATUS 0x2E - -#define TWL6040_CACHEREGNUM (TWL6040_REG_STATUS + 1) - -#define TWL6040_VIOREGNUM 18 -#define TWL6040_VDDREGNUM 21 - -/* INTID (0x03) fields */ - -#define TWL6040_THINT 0x01 -#define TWL6040_PLUGINT 0x02 -#define TWL6040_UNPLUGINT 0x04 -#define TWL6040_HOOKINT 0x08 -#define TWL6040_HFINT 0x10 -#define TWL6040_VIBINT 0x20 -#define TWL6040_READYINT 0x40 - -/* INTMR (0x04) fields */ - -#define TWL6040_PLUGMSK 0x02 -#define TWL6040_READYMSK 0x40 -#define TWL6040_ALLINT_MSK 0x7B - -/* NCPCTL (0x05) fields */ - -#define TWL6040_NCPENA 0x01 -#define TWL6040_NCPOPEN 0x40 - -/* LDOCTL (0x06) fields */ - -#define TWL6040_LSLDOENA 0x01 -#define TWL6040_HSLDOENA 0x04 -#define TWL6040_REFENA 0x40 -#define TWL6040_OSCENA 0x80 - -/* HPPLLCTL (0x07) fields */ - -#define TWL6040_HPLLENA 0x01 -#define TWL6040_HPLLRST 0x02 -#define TWL6040_HPLLBP 0x04 -#define TWL6040_HPLLSQRENA 0x08 -#define TWL6040_HPLLSQRBP 0x10 -#define TWL6040_MCLK_12000KHZ (0 << 5) -#define TWL6040_MCLK_19200KHZ (1 << 5) -#define TWL6040_MCLK_26000KHZ (2 << 5) -#define TWL6040_MCLK_38400KHZ (3 << 5) -#define TWL6040_MCLK_MSK 0x60 - -/* LPPLLCTL (0x08) fields */ - -#define TWL6040_LPLLENA 0x01 -#define TWL6040_LPLLRST 0x02 -#define TWL6040_LPLLSEL 0x04 -#define TWL6040_LPLLFIN 0x08 -#define TWL6040_HPLLSEL 0x10 - -/* HSLCTL (0x10) fields */ - -#define TWL6040_HSDACMODEL 0x02 -#define TWL6040_HSDRVMODEL 0x08 - -/* HSRCTL (0x11) fields */ - -#define TWL6040_HSDACMODER 0x02 -#define TWL6040_HSDRVMODER 0x08 - -/* ACCCTL (0x2D) fields */ - -#define TWL6040_RESETSPLIT 0x04 - -#define TWL6040_SYSCLK_SEL_LPPLL 1 -#define TWL6040_SYSCLK_SEL_HPPLL 2 - -#define TWL6040_HPPLL_ID 1 -#define TWL6040_LPPLL_ID 2 - -/* STATUS (0x2E) fields */ - -#define TWL6040_PLUGCOMP 0x02 - void twl6040_hs_jack_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack, int report);
diff --git a/sound/soc/omap/sdp4430.c b/sound/soc/omap/sdp4430.c index 189e039..5d67c25 100644 --- a/sound/soc/omap/sdp4430.c +++ b/sound/soc/omap/sdp4430.c @@ -21,6 +21,8 @@
#include <linux/clk.h> #include <linux/platform_device.h> +#include <linux/mfd/twl6040.h> + #include <sound/core.h> #include <sound/pcm.h> #include <sound/soc.h>
Pass twl4030_codec_data instead of the twl4030_audio_data for the ASoC codec driver.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- drivers/mfd/twl6040-core.c | 5 ++--- 1 files changed, 2 insertions(+), 3 deletions(-)
diff --git a/drivers/mfd/twl6040-core.c b/drivers/mfd/twl6040-core.c index 195613c..b6e5338 100644 --- a/drivers/mfd/twl6040-core.c +++ b/drivers/mfd/twl6040-core.c @@ -507,9 +507,8 @@ static int __devinit twl6040_probe(struct platform_device *pdev) if (pdata->codec) { cell = &twl6040->cells[children]; cell->name = "twl6040-codec"; - /* The codec expects the twl4030_audio_data as platform data */ - cell->platform_data = pdata; - cell->pdata_size = sizeof(*pdata); + cell->platform_data = pdata->codec; + cell->pdata_size = sizeof(*pdata->codec); children++; }
From: Misael Lopez Cruz misael.lopez@ti.com
Add twl6040_vibra as a child of MFD device twl6040_codec. This implementation covers the PCM-to-PWM mode of TWL6040 vibrator module.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com CC: Tejun Heo tj@kernel.org --- drivers/input/misc/Kconfig | 11 + drivers/input/misc/Makefile | 1 + drivers/input/misc/twl6040-vibra.c | 416 ++++++++++++++++++++++++++++++++++++ include/linux/i2c/twl.h | 8 + 4 files changed, 436 insertions(+), 0 deletions(-) create mode 100644 drivers/input/misc/twl6040-vibra.c
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 077309a..d1bf872 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -275,6 +275,17 @@ config INPUT_TWL4030_VIBRA To compile this driver as a module, choose M here. The module will be called twl4030_vibra.
+config INPUT_TWL6040_VIBRA + tristate "Support for TWL6040 Vibrator" + depends on TWL4030_CORE + select TWL6040_CORE + select INPUT_FF_MEMLESS + help + This option enables support for TWL6040 Vibrator Driver. + + To compile this driver as a module, choose M here. The module will + be called twl6040_vibra. + config INPUT_UINPUT tristate "User level driver support" help diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index 38efb2c..4da7c3a 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -40,6 +40,7 @@ obj-$(CONFIG_INPUT_SGI_BTNS) += sgi_btns.o obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON) += twl4030-pwrbutton.o obj-$(CONFIG_INPUT_TWL4030_VIBRA) += twl4030-vibra.o +obj-$(CONFIG_INPUT_TWL6040_VIBRA) += twl6040-vibra.o obj-$(CONFIG_INPUT_UINPUT) += uinput.o obj-$(CONFIG_INPUT_WISTRON_BTNS) += wistron_btns.o obj-$(CONFIG_INPUT_WM831X_ON) += wm831x-on.o diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c new file mode 100644 index 0000000..9652ebf --- /dev/null +++ b/drivers/input/misc/twl6040-vibra.c @@ -0,0 +1,416 @@ +/* + * twl6040-vibra.c - TWL6040 Vibrator driver + * + * Author: Jorge Eduardo Candelaria jorge.candelaria@ti.com + * Author: Misael Lopez Cruz misael.lopez@ti.com + * + * Copyright: (C) 2011 Texas Instruments, Inc. + * + * Based on twl4030-vibra.c by Henrik Saari henrik.saari@nokia.com + * Felipe Balbi felipe.balbi@nokia.com + * Jari Vanhala ext-javi.vanhala@nokia.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA + * 02110-1301 USA + * + */ +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/workqueue.h> +#include <linux/i2c/twl.h> +#include <linux/mfd/twl6040.h> +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/regulator/consumer.h> + +#define EFFECT_DIR_180_DEG 0x8000 + +/* Recommended modulation index 85% */ +#define TWL6040_VIBRA_MOD 85 + +#define TWL6040_NUM_SUPPLIES 2 + +struct vibra_info { + struct device *dev; + struct input_dev *input_dev; + struct workqueue_struct *workqueue; + struct work_struct play_work; + struct mutex mutex; + + bool enabled; + int weak_speed; + int strong_speed; + int direction; + + unsigned int vibldrv_res; + unsigned int vibrdrv_res; + unsigned int viblmotor_res; + unsigned int vibrmotor_res; + + struct regulator_bulk_data supplies[TWL6040_NUM_SUPPLIES]; + + struct twl6040 *twl6040; +}; + +static irqreturn_t twl6040_vib_irq_handler(int irq, void *data) +{ + struct vibra_info *info = data; + struct twl6040 *twl6040 = info->twl6040; + u8 status; + + status = twl6040_reg_read(twl6040, TWL6040_REG_STATUS); + if (status & TWL6040_VIBLOCDET) { + dev_warn(info->dev, "Left Vibrator overcurrent detected\n"); + twl6040_clear_bits(twl6040, TWL6040_REG_VIBCTLL, + TWL6040_VIBENAL); + } + if (status & TWL6040_VIBROCDET) { + dev_warn(info->dev, "Right Vibrator overcurrent detected\n"); + twl6040_clear_bits(twl6040, TWL6040_REG_VIBCTLR, + TWL6040_VIBENAR); + } + + return IRQ_HANDLED; +} + +static void twl6040_vibra_enable(struct vibra_info *info) +{ + struct twl6040 *twl6040 = info->twl6040; + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(info->supplies), info->supplies); + if (ret) { + dev_err(info->dev, "failed to enable regulators %d\n", ret); + return; + } + + twl6040_power(info->twl6040, 1); + if (twl6040_get_rev(twl6040) <= TWL6040_REV_ES1_1) { + /* + * ERRATA: Disable overcurrent protection for at least + * 3ms when enabling vibrator drivers to avoid false + * overcurrent detection + */ + twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLL, + TWL6040_VIBENAL | TWL6040_VIBCTRLL); + twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLR, + TWL6040_VIBENAR | TWL6040_VIBCTRLR); + usleep_range(3000, 3500); + } + + twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLL, + TWL6040_VIBENAL); + twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLR, + TWL6040_VIBENAR); + + info->enabled = true; +} + +static void twl6040_vibra_disable(struct vibra_info *info) +{ + struct twl6040 *twl6040 = info->twl6040; + + twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLL, 0x00); + twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLR, 0x00); + twl6040_power(info->twl6040, 0); + + regulator_bulk_disable(ARRAY_SIZE(info->supplies), info->supplies); + + info->enabled = false; +} + +static u8 twl6040_vibra_code(int vddvib, int vibdrv_res, int motor_res, + int speed, int direction) +{ + int vpk, max_code; + u8 vibdat; + + /* output swing */ + vpk = (vddvib * motor_res * TWL6040_VIBRA_MOD) / + (100 * (vibdrv_res + motor_res)); + + /* 50mV per VIBDAT code step */ + max_code = vpk / 50; + if (max_code > TWL6040_VIBDAT_MAX) + max_code = TWL6040_VIBDAT_MAX; + + /* scale speed to max allowed code */ + vibdat = (u8)((speed * max_code) / USHRT_MAX); + + /* 2's complement for direction > 180 degrees */ + vibdat *= direction; + + return vibdat; +} + +static void twl6040_vibra_set_effect(struct vibra_info *info) +{ + struct twl6040 *twl6040 = info->twl6040; + u8 vibdatl, vibdatr; + int volt; + + /* weak motor */ + volt = regulator_get_voltage(info->supplies[0].consumer) / 1000; + vibdatl = twl6040_vibra_code(volt, info->vibldrv_res, + info->viblmotor_res, + info->weak_speed, info->direction); + + /* strong motor */ + volt = regulator_get_voltage(info->supplies[1].consumer) / 1000; + vibdatr = twl6040_vibra_code(volt, info->vibrdrv_res, + info->vibrmotor_res, + info->strong_speed, info->direction); + + twl6040_reg_write(twl6040, TWL6040_REG_VIBDATL, vibdatl); + twl6040_reg_write(twl6040, TWL6040_REG_VIBDATR, vibdatr); +} + +static void vibra_play_work(struct work_struct *work) +{ + struct vibra_info *info = container_of(work, + struct vibra_info, play_work); + + mutex_lock(&info->mutex); + + if (info->weak_speed || info->strong_speed) { + if (!info->enabled) + twl6040_vibra_enable(info); + + twl6040_vibra_set_effect(info); + } else if (info->enabled) + twl6040_vibra_disable(info); + + mutex_unlock(&info->mutex); +} + +static int vibra_play(struct input_dev *input, void *data, + struct ff_effect *effect) +{ + struct vibra_info *info = input_get_drvdata(input); + int ret; + + info->weak_speed = effect->u.rumble.weak_magnitude; + info->strong_speed = effect->u.rumble.strong_magnitude; + info->direction = effect->direction < EFFECT_DIR_180_DEG ? 1 : -1; + + ret = queue_work(info->workqueue, &info->play_work); + if (!ret) { + dev_info(&input->dev, "work is already on queue\n"); + return ret; + } + + return 0; +} + +static void twl6040_vibra_close(struct input_dev *input) +{ + struct vibra_info *info = input_get_drvdata(input); + + cancel_work_sync(&info->play_work); + + mutex_lock(&info->mutex); + + if (info->enabled) + twl6040_vibra_disable(info); + + mutex_unlock(&info->mutex); +} + +#if CONFIG_PM_SLEEP +static int twl6040_vibra_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct vibra_info *info = platform_get_drvdata(pdev); + + mutex_lock(&info->mutex); + + if (info->enabled) + twl6040_vibra_disable(info); + + mutex_unlock(&info->mutex); + + return 0; +} + +#endif + +static SIMPLE_DEV_PM_OPS(twl6040_vibra_pm_ops, twl6040_vibra_suspend, NULL); + +static int __devinit twl6040_vibra_probe(struct platform_device *pdev) +{ + struct twl4030_vibra_data *pdata = pdev->dev.platform_data; + struct vibra_info *info; + int ret; + + if (!pdata) { + dev_err(&pdev->dev, "platform_data not available\n"); + return -EINVAL; + } + + info = kzalloc(sizeof(*info), GFP_KERNEL); + if (!info) { + dev_err(&pdev->dev, "couldn't allocate memory\n"); + return -ENOMEM; + } + + info->dev = &pdev->dev; + info->twl6040 = dev_get_drvdata(pdev->dev.parent); + info->vibldrv_res = pdata->vibldrv_res; + info->vibrdrv_res = pdata->vibrdrv_res; + info->viblmotor_res = pdata->viblmotor_res; + info->vibrmotor_res = pdata->vibrmotor_res; + if ((!info->vibldrv_res && !info->viblmotor_res) || + (!info->vibrdrv_res && !info->vibrmotor_res)) { + dev_err(info->dev, "invalid vibra driver/motor resistance\n"); + ret = -EINVAL; + goto err_kzalloc; + } + + mutex_init(&info->mutex); + + info->input_dev = input_allocate_device(); + if (info->input_dev == NULL) { + dev_err(info->dev, "couldn't allocate input device\n"); + ret = -ENOMEM; + goto err_kzalloc; + } + + input_set_drvdata(info->input_dev, info); + + info->input_dev->name = "twl6040:vibrator"; + info->input_dev->id.version = 1; + info->input_dev->dev.parent = pdev->dev.parent; + info->input_dev->close = twl6040_vibra_close; + __set_bit(FF_RUMBLE, info->input_dev->ffbit); + + ret = input_ff_create_memless(info->input_dev, NULL, vibra_play); + if (ret < 0) { + dev_err(info->dev, "couldn't register vibrator to FF\n"); + goto err_ialloc; + } + + ret = input_register_device(info->input_dev); + if (ret < 0) { + dev_err(info->dev, "couldn't register input device\n"); + goto err_iff; + } + + platform_set_drvdata(pdev, info); + + ret = twl6040_request_irq(info->twl6040, TWL6040_IRQ_VIB, + twl6040_vib_irq_handler, 0, + "twl6040_irq_vib", info); + if (ret) { + dev_err(info->dev, "VIB IRQ request failed: %d\n", ret); + goto err_irq; + } + + info->supplies[0].supply = "vddvibl"; + info->supplies[1].supply = "vddvibr"; + ret = regulator_bulk_get(info->dev, ARRAY_SIZE(info->supplies), + info->supplies); + if (ret) { + dev_err(info->dev, "couldn't get regulators %d\n", ret); + goto err_regulator; + } + + if (pdata->vddvibl_uV) { + ret = regulator_set_voltage(info->supplies[0].consumer, + pdata->vddvibl_uV, + pdata->vddvibl_uV); + if (ret) { + dev_err(info->dev, "failed to set VDDVIBL volt %d\n", + ret); + goto err_voltage; + } + } + + if (pdata->vddvibr_uV) { + ret = regulator_set_voltage(info->supplies[1].consumer, + pdata->vddvibr_uV, + pdata->vddvibr_uV); + if (ret) { + dev_err(info->dev, "failed to set VDDVIBR volt %d\n", + ret); + goto err_voltage; + } + } + + info->workqueue = alloc_workqueue("twl6040-vibra", 0, 0); + if (info->workqueue == NULL) { + dev_err(info->dev, "couldn't create workqueue\n"); + ret = -ENOMEM; + goto err_voltage; + } + INIT_WORK(&info->play_work, vibra_play_work); + + return 0; + +err_voltage: + regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); +err_regulator: + twl6040_free_irq(info->twl6040, TWL6040_IRQ_VIB, info); +err_irq: + input_unregister_device(info->input_dev); + info->input_dev = NULL; +err_iff: + if (info->input_dev) + input_ff_destroy(info->input_dev); +err_ialloc: + input_free_device(info->input_dev); +err_kzalloc: + kfree(info); + return ret; +} + +static int __devexit twl6040_vibra_remove(struct platform_device *pdev) +{ + struct vibra_info *info = platform_get_drvdata(pdev); + + input_unregister_device(info->input_dev); + twl6040_free_irq(info->twl6040, TWL6040_IRQ_VIB, info); + regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies); + destroy_workqueue(info->workqueue); + kfree(info); + + return 0; +} + +static struct platform_driver twl6040_vibra_driver = { + .probe = twl6040_vibra_probe, + .remove = __devexit_p(twl6040_vibra_remove), + .driver = { + .name = "twl6040-vibra", + .owner = THIS_MODULE, + .pm = &twl6040_vibra_pm_ops, + }, +}; + +static int __init twl6040_vibra_init(void) +{ + return platform_driver_register(&twl6040_vibra_driver); +} +module_init(twl6040_vibra_init); + +static void __exit twl6040_vibra_exit(void) +{ + platform_driver_unregister(&twl6040_vibra_driver); +} +module_exit(twl6040_vibra_exit); + +MODULE_ALIAS("platform:twl6040-vibra"); +MODULE_DESCRIPTION("TWL6040 Vibra driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Jorge Eduardo Candelaria jorge.candelaria@ti.com"); +MODULE_AUTHOR("Misael Lopez Cruz misael.lopez@ti.com"); diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index ea5baa2..685fd76 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -669,6 +669,14 @@ struct twl4030_codec_data {
struct twl4030_vibra_data { unsigned int coexist; + + /* twl6040 */ + unsigned int vibldrv_res; /* left driver resistance */ + unsigned int vibrdrv_res; /* right driver resistance */ + unsigned int viblmotor_res; /* left motor resistance */ + unsigned int vibrmotor_res; /* right motor resistance */ + int vddvibl_uV; /* VDDVIBL volt, set 0 for fixed reg */ + int vddvibr_uV; /* VDDVIBR volt, set 0 for fixed reg */ };
struct twl4030_audio_data {
On Tue, Jun 21, 2011 at 04:39:09PM +0300, Peter Ujfalusi wrote:
From: Misael Lopez Cruz misael.lopez@ti.com
Add twl6040_vibra as a child of MFD device twl6040_codec. This implementation covers the PCM-to-PWM mode of TWL6040 vibrator module.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com CC: Tejun Heo tj@kernel.org
Peter,
As Tejun mentioned, there is no difference between having a "private" workqueue created with alloc_workqueue() with default parameters and using system-wide workqueue. Therefore please use system-wide one. If your use shows that you indeed need high-priority workqueue it can be added later.
Otherwise:
Acked-by: Dmitry Torokhov dtor@mail.ru
Please feel free to merge this code with the rest of TWL6040 patches (presumably throgh Samuel's MFD tree).
Thanks.
drivers/input/misc/Kconfig | 11 + drivers/input/misc/Makefile | 1 + drivers/input/misc/twl6040-vibra.c | 416 ++++++++++++++++++++++++++++++++++++ include/linux/i2c/twl.h | 8 + 4 files changed, 436 insertions(+), 0 deletions(-) create mode 100644 drivers/input/misc/twl6040-vibra.c
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index 077309a..d1bf872 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -275,6 +275,17 @@ config INPUT_TWL4030_VIBRA To compile this driver as a module, choose M here. The module will be called twl4030_vibra.
+config INPUT_TWL6040_VIBRA
- tristate "Support for TWL6040 Vibrator"
- depends on TWL4030_CORE
- select TWL6040_CORE
- select INPUT_FF_MEMLESS
- help
This option enables support for TWL6040 Vibrator Driver.
To compile this driver as a module, choose M here. The module will
be called twl6040_vibra.
config INPUT_UINPUT tristate "User level driver support" help diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index 38efb2c..4da7c3a 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -40,6 +40,7 @@ obj-$(CONFIG_INPUT_SGI_BTNS) += sgi_btns.o obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON) += twl4030-pwrbutton.o obj-$(CONFIG_INPUT_TWL4030_VIBRA) += twl4030-vibra.o +obj-$(CONFIG_INPUT_TWL6040_VIBRA) += twl6040-vibra.o obj-$(CONFIG_INPUT_UINPUT) += uinput.o obj-$(CONFIG_INPUT_WISTRON_BTNS) += wistron_btns.o obj-$(CONFIG_INPUT_WM831X_ON) += wm831x-on.o diff --git a/drivers/input/misc/twl6040-vibra.c b/drivers/input/misc/twl6040-vibra.c new file mode 100644 index 0000000..9652ebf --- /dev/null +++ b/drivers/input/misc/twl6040-vibra.c @@ -0,0 +1,416 @@ +/*
- twl6040-vibra.c - TWL6040 Vibrator driver
- Author: Jorge Eduardo Candelaria jorge.candelaria@ti.com
- Author: Misael Lopez Cruz misael.lopez@ti.com
- Copyright: (C) 2011 Texas Instruments, Inc.
- Based on twl4030-vibra.c by Henrik Saari henrik.saari@nokia.com
Felipe Balbi <felipe.balbi@nokia.com>
Jari Vanhala <ext-javi.vanhala@nokia.com>
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License version 2 as
- published by the Free Software Foundation.
- This program is distributed in the hope that it will be useful, but
- WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- General Public License for more details.
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- 02110-1301 USA
- */
+#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/workqueue.h> +#include <linux/i2c/twl.h> +#include <linux/mfd/twl6040.h> +#include <linux/slab.h> +#include <linux/delay.h> +#include <linux/regulator/consumer.h>
+#define EFFECT_DIR_180_DEG 0x8000
+/* Recommended modulation index 85% */ +#define TWL6040_VIBRA_MOD 85
+#define TWL6040_NUM_SUPPLIES 2
+struct vibra_info {
- struct device *dev;
- struct input_dev *input_dev;
- struct workqueue_struct *workqueue;
- struct work_struct play_work;
- struct mutex mutex;
- bool enabled;
- int weak_speed;
- int strong_speed;
- int direction;
- unsigned int vibldrv_res;
- unsigned int vibrdrv_res;
- unsigned int viblmotor_res;
- unsigned int vibrmotor_res;
- struct regulator_bulk_data supplies[TWL6040_NUM_SUPPLIES];
- struct twl6040 *twl6040;
+};
+static irqreturn_t twl6040_vib_irq_handler(int irq, void *data) +{
- struct vibra_info *info = data;
- struct twl6040 *twl6040 = info->twl6040;
- u8 status;
- status = twl6040_reg_read(twl6040, TWL6040_REG_STATUS);
- if (status & TWL6040_VIBLOCDET) {
dev_warn(info->dev, "Left Vibrator overcurrent detected\n");
twl6040_clear_bits(twl6040, TWL6040_REG_VIBCTLL,
TWL6040_VIBENAL);
- }
- if (status & TWL6040_VIBROCDET) {
dev_warn(info->dev, "Right Vibrator overcurrent detected\n");
twl6040_clear_bits(twl6040, TWL6040_REG_VIBCTLR,
TWL6040_VIBENAR);
- }
- return IRQ_HANDLED;
+}
+static void twl6040_vibra_enable(struct vibra_info *info) +{
- struct twl6040 *twl6040 = info->twl6040;
- int ret;
- ret = regulator_bulk_enable(ARRAY_SIZE(info->supplies), info->supplies);
- if (ret) {
dev_err(info->dev, "failed to enable regulators %d\n", ret);
return;
- }
- twl6040_power(info->twl6040, 1);
- if (twl6040_get_rev(twl6040) <= TWL6040_REV_ES1_1) {
/*
* ERRATA: Disable overcurrent protection for at least
* 3ms when enabling vibrator drivers to avoid false
* overcurrent detection
*/
twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLL,
TWL6040_VIBENAL | TWL6040_VIBCTRLL);
twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLR,
TWL6040_VIBENAR | TWL6040_VIBCTRLR);
usleep_range(3000, 3500);
- }
- twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLL,
TWL6040_VIBENAL);
- twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLR,
TWL6040_VIBENAR);
- info->enabled = true;
+}
+static void twl6040_vibra_disable(struct vibra_info *info) +{
- struct twl6040 *twl6040 = info->twl6040;
- twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLL, 0x00);
- twl6040_reg_write(twl6040, TWL6040_REG_VIBCTLR, 0x00);
- twl6040_power(info->twl6040, 0);
- regulator_bulk_disable(ARRAY_SIZE(info->supplies), info->supplies);
- info->enabled = false;
+}
+static u8 twl6040_vibra_code(int vddvib, int vibdrv_res, int motor_res,
int speed, int direction)
+{
- int vpk, max_code;
- u8 vibdat;
- /* output swing */
- vpk = (vddvib * motor_res * TWL6040_VIBRA_MOD) /
(100 * (vibdrv_res + motor_res));
- /* 50mV per VIBDAT code step */
- max_code = vpk / 50;
- if (max_code > TWL6040_VIBDAT_MAX)
max_code = TWL6040_VIBDAT_MAX;
- /* scale speed to max allowed code */
- vibdat = (u8)((speed * max_code) / USHRT_MAX);
- /* 2's complement for direction > 180 degrees */
- vibdat *= direction;
- return vibdat;
+}
+static void twl6040_vibra_set_effect(struct vibra_info *info) +{
- struct twl6040 *twl6040 = info->twl6040;
- u8 vibdatl, vibdatr;
- int volt;
- /* weak motor */
- volt = regulator_get_voltage(info->supplies[0].consumer) / 1000;
- vibdatl = twl6040_vibra_code(volt, info->vibldrv_res,
info->viblmotor_res,
info->weak_speed, info->direction);
- /* strong motor */
- volt = regulator_get_voltage(info->supplies[1].consumer) / 1000;
- vibdatr = twl6040_vibra_code(volt, info->vibrdrv_res,
info->vibrmotor_res,
info->strong_speed, info->direction);
- twl6040_reg_write(twl6040, TWL6040_REG_VIBDATL, vibdatl);
- twl6040_reg_write(twl6040, TWL6040_REG_VIBDATR, vibdatr);
+}
+static void vibra_play_work(struct work_struct *work) +{
- struct vibra_info *info = container_of(work,
struct vibra_info, play_work);
- mutex_lock(&info->mutex);
- if (info->weak_speed || info->strong_speed) {
if (!info->enabled)
twl6040_vibra_enable(info);
twl6040_vibra_set_effect(info);
- } else if (info->enabled)
twl6040_vibra_disable(info);
- mutex_unlock(&info->mutex);
+}
+static int vibra_play(struct input_dev *input, void *data,
struct ff_effect *effect)
+{
- struct vibra_info *info = input_get_drvdata(input);
- int ret;
- info->weak_speed = effect->u.rumble.weak_magnitude;
- info->strong_speed = effect->u.rumble.strong_magnitude;
- info->direction = effect->direction < EFFECT_DIR_180_DEG ? 1 : -1;
- ret = queue_work(info->workqueue, &info->play_work);
- if (!ret) {
dev_info(&input->dev, "work is already on queue\n");
return ret;
- }
- return 0;
+}
+static void twl6040_vibra_close(struct input_dev *input) +{
- struct vibra_info *info = input_get_drvdata(input);
- cancel_work_sync(&info->play_work);
- mutex_lock(&info->mutex);
- if (info->enabled)
twl6040_vibra_disable(info);
- mutex_unlock(&info->mutex);
+}
+#if CONFIG_PM_SLEEP +static int twl6040_vibra_suspend(struct device *dev) +{
- struct platform_device *pdev = to_platform_device(dev);
- struct vibra_info *info = platform_get_drvdata(pdev);
- mutex_lock(&info->mutex);
- if (info->enabled)
twl6040_vibra_disable(info);
- mutex_unlock(&info->mutex);
- return 0;
+}
+#endif
+static SIMPLE_DEV_PM_OPS(twl6040_vibra_pm_ops, twl6040_vibra_suspend, NULL);
+static int __devinit twl6040_vibra_probe(struct platform_device *pdev) +{
- struct twl4030_vibra_data *pdata = pdev->dev.platform_data;
- struct vibra_info *info;
- int ret;
- if (!pdata) {
dev_err(&pdev->dev, "platform_data not available\n");
return -EINVAL;
- }
- info = kzalloc(sizeof(*info), GFP_KERNEL);
- if (!info) {
dev_err(&pdev->dev, "couldn't allocate memory\n");
return -ENOMEM;
- }
- info->dev = &pdev->dev;
- info->twl6040 = dev_get_drvdata(pdev->dev.parent);
- info->vibldrv_res = pdata->vibldrv_res;
- info->vibrdrv_res = pdata->vibrdrv_res;
- info->viblmotor_res = pdata->viblmotor_res;
- info->vibrmotor_res = pdata->vibrmotor_res;
- if ((!info->vibldrv_res && !info->viblmotor_res) ||
(!info->vibrdrv_res && !info->vibrmotor_res)) {
dev_err(info->dev, "invalid vibra driver/motor resistance\n");
ret = -EINVAL;
goto err_kzalloc;
- }
- mutex_init(&info->mutex);
- info->input_dev = input_allocate_device();
- if (info->input_dev == NULL) {
dev_err(info->dev, "couldn't allocate input device\n");
ret = -ENOMEM;
goto err_kzalloc;
- }
- input_set_drvdata(info->input_dev, info);
- info->input_dev->name = "twl6040:vibrator";
- info->input_dev->id.version = 1;
- info->input_dev->dev.parent = pdev->dev.parent;
- info->input_dev->close = twl6040_vibra_close;
- __set_bit(FF_RUMBLE, info->input_dev->ffbit);
- ret = input_ff_create_memless(info->input_dev, NULL, vibra_play);
- if (ret < 0) {
dev_err(info->dev, "couldn't register vibrator to FF\n");
goto err_ialloc;
- }
- ret = input_register_device(info->input_dev);
- if (ret < 0) {
dev_err(info->dev, "couldn't register input device\n");
goto err_iff;
- }
- platform_set_drvdata(pdev, info);
- ret = twl6040_request_irq(info->twl6040, TWL6040_IRQ_VIB,
twl6040_vib_irq_handler, 0,
"twl6040_irq_vib", info);
- if (ret) {
dev_err(info->dev, "VIB IRQ request failed: %d\n", ret);
goto err_irq;
- }
- info->supplies[0].supply = "vddvibl";
- info->supplies[1].supply = "vddvibr";
- ret = regulator_bulk_get(info->dev, ARRAY_SIZE(info->supplies),
info->supplies);
- if (ret) {
dev_err(info->dev, "couldn't get regulators %d\n", ret);
goto err_regulator;
- }
- if (pdata->vddvibl_uV) {
ret = regulator_set_voltage(info->supplies[0].consumer,
pdata->vddvibl_uV,
pdata->vddvibl_uV);
if (ret) {
dev_err(info->dev, "failed to set VDDVIBL volt %d\n",
ret);
goto err_voltage;
}
- }
- if (pdata->vddvibr_uV) {
ret = regulator_set_voltage(info->supplies[1].consumer,
pdata->vddvibr_uV,
pdata->vddvibr_uV);
if (ret) {
dev_err(info->dev, "failed to set VDDVIBR volt %d\n",
ret);
goto err_voltage;
}
- }
- info->workqueue = alloc_workqueue("twl6040-vibra", 0, 0);
- if (info->workqueue == NULL) {
dev_err(info->dev, "couldn't create workqueue\n");
ret = -ENOMEM;
goto err_voltage;
- }
- INIT_WORK(&info->play_work, vibra_play_work);
- return 0;
+err_voltage:
- regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies);
+err_regulator:
- twl6040_free_irq(info->twl6040, TWL6040_IRQ_VIB, info);
+err_irq:
- input_unregister_device(info->input_dev);
- info->input_dev = NULL;
+err_iff:
- if (info->input_dev)
input_ff_destroy(info->input_dev);
+err_ialloc:
- input_free_device(info->input_dev);
+err_kzalloc:
- kfree(info);
- return ret;
+}
+static int __devexit twl6040_vibra_remove(struct platform_device *pdev) +{
- struct vibra_info *info = platform_get_drvdata(pdev);
- input_unregister_device(info->input_dev);
- twl6040_free_irq(info->twl6040, TWL6040_IRQ_VIB, info);
- regulator_bulk_free(ARRAY_SIZE(info->supplies), info->supplies);
- destroy_workqueue(info->workqueue);
- kfree(info);
- return 0;
+}
+static struct platform_driver twl6040_vibra_driver = {
- .probe = twl6040_vibra_probe,
- .remove = __devexit_p(twl6040_vibra_remove),
- .driver = {
.name = "twl6040-vibra",
.owner = THIS_MODULE,
.pm = &twl6040_vibra_pm_ops,
- },
+};
+static int __init twl6040_vibra_init(void) +{
- return platform_driver_register(&twl6040_vibra_driver);
+} +module_init(twl6040_vibra_init);
+static void __exit twl6040_vibra_exit(void) +{
- platform_driver_unregister(&twl6040_vibra_driver);
+} +module_exit(twl6040_vibra_exit);
+MODULE_ALIAS("platform:twl6040-vibra"); +MODULE_DESCRIPTION("TWL6040 Vibra driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Jorge Eduardo Candelaria jorge.candelaria@ti.com"); +MODULE_AUTHOR("Misael Lopez Cruz misael.lopez@ti.com"); diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index ea5baa2..685fd76 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -669,6 +669,14 @@ struct twl4030_codec_data {
struct twl4030_vibra_data { unsigned int coexist;
- /* twl6040 */
- unsigned int vibldrv_res; /* left driver resistance */
- unsigned int vibrdrv_res; /* right driver resistance */
- unsigned int viblmotor_res; /* left motor resistance */
- unsigned int vibrmotor_res; /* right motor resistance */
- int vddvibl_uV; /* VDDVIBL volt, set 0 for fixed reg */
- int vddvibr_uV; /* VDDVIBR volt, set 0 for fixed reg */
};
struct twl4030_audio_data {
1.7.5.3
Hello Dmitry,
On Tuesday 21 June 2011 22:32:01 Dmitry Torokhov wrote:
On Tue, Jun 21, 2011 at 04:39:09PM +0300, Peter Ujfalusi wrote:
From: Misael Lopez Cruz misael.lopez@ti.com
Add twl6040_vibra as a child of MFD device twl6040_codec. This implementation covers the PCM-to-PWM mode of TWL6040 vibrator module.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com CC: Tejun Heo tj@kernel.org
Peter,
As Tejun mentioned, there is no difference between having a "private" workqueue created with alloc_workqueue() with default parameters and using system-wide workqueue. Therefore please use system-wide one. If your use shows that you indeed need high-priority workqueue it can be added later.
I have replaced the singlethreaded wq with the call suggested by Tejun: https://lkml.org/lkml/2011/6/17/99
If this is a problem, I can rework this, and remove the code, which is not going to be needed, when the system_wq is in use, but I would like to keep the alloc_workqueue way, since it is going to be easier for us to experiment with parameters, if we face with issues.
Otherwise:
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Please feel free to merge this code with the rest of TWL6040 patches (presumably throgh Samuel's MFD tree).
Thank you, Péter
Add twl4030_vibra platform data, and the needed regulators for twl6040 vibrator.
Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/board-4430sdp.c | 48 +++++++++++++++++++++++++++++++++++ 1 files changed, 48 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index 968029a..266d146 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -22,6 +22,7 @@ #include <linux/i2c/twl.h> #include <linux/gpio_keys.h> #include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> #include <linux/leds.h> #include <linux/leds_pwm.h>
@@ -276,11 +277,40 @@ static struct platform_device sdp4430_lcd_device = { .id = -1, };
+static struct regulator_consumer_supply sdp4430_vbat_supply[] = { + REGULATOR_SUPPLY("vddvibl", "twl6040-vibra"), + REGULATOR_SUPPLY("vddvibr", "twl6040-vibra"), +}; + +static struct regulator_init_data sdp4430_vbat_data = { + .constraints = { + .always_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(sdp4430_vbat_supply), + .consumer_supplies = sdp4430_vbat_supply, +}; + +static struct fixed_voltage_config sdp4430_vbat_pdata = { + .supply_name = "VBAT", + .microvolts = 3750000, + .init_data = &sdp4430_vbat_data, + .gpio = -EINVAL, +}; + +static struct platform_device sdp4430_vbat = { + .name = "reg-fixed-voltage", + .id = -1, + .dev = { + .platform_data = &sdp4430_vbat_pdata, + }, +}; + static struct platform_device *sdp4430_devices[] __initdata = { &sdp4430_lcd_device, &sdp4430_gpio_keys_device, &sdp4430_leds_gpio, &sdp4430_leds_pwm, + &sdp4430_vbat, };
static struct omap_lcd_config sdp4430_lcd_config __initdata = { @@ -402,7 +432,25 @@ static struct regulator_init_data sdp4430_vusim = { }, };
+static struct twl4030_vibra_data twl6040_vibra = { + .vibldrv_res = 8, + .vibrdrv_res = 3, + .viblmotor_res = 10, + .vibrmotor_res = 10, + .vddvibl_uV = 0, /* fixed volt supply - VBAT */ + .vddvibr_uV = 0, /* fixed volt supply - VBAT */ +}; + +static struct twl4030_audio_data twl6040_audio = { + .codec = NULL, + .vibra = &twl6040_vibra, + .audpwron_gpio = 127, + .naudint_irq = OMAP44XX_IRQ_SYS_2N, + .irq_base = TWL6040_CODEC_IRQ_BASE, +}; + static struct twl4030_platform_data sdp4430_twldata = { + .audio = &twl6040_audio, /* Regulators */ .vusim = &sdp4430_vusim, .vaux1 = &sdp4430_vaux1,
From: Liam Girdwood lrg@ti.com
Add all DAIs to fully support OMAP4 ABE.
Signed-off-by: Liam Girdwood lrg@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com --- sound/soc/codecs/twl6040.c | 44 ++++++++++++++++++++++++++++++++++++-------- 1 files changed, 36 insertions(+), 8 deletions(-)
diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index a20e293..28dc5d9 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -1359,23 +1359,51 @@ static struct snd_soc_dai_ops twl6040_dai_ops = { .set_sysclk = twl6040_set_dai_sysclk, };
-static struct snd_soc_dai_driver twl6040_dai = { - .name = "twl6040-hifi", +static struct snd_soc_dai_driver twl6040_dai[] = { +{ + .name = "twl6040-ul", + .capture = { + .stream_name = "Capture", + .channels_min = 1, + .channels_max = 2, + .rates = TWL6040_RATES, + .formats = TWL6040_FORMATS, + }, + .ops = &twl6040_dai_ops, +}, +{ + .name = "twl6040-dl1", .playback = { - .stream_name = "Playback", + .stream_name = "Headset Playback", .channels_min = 1, - .channels_max = 4, + .channels_max = 2, .rates = TWL6040_RATES, .formats = TWL6040_FORMATS, }, - .capture = { - .stream_name = "Capture", + .ops = &twl6040_dai_ops, +}, +{ + .name = "twl6040-dl2", + .playback = { + .stream_name = "Handsfree Playback", .channels_min = 1, .channels_max = 2, .rates = TWL6040_RATES, .formats = TWL6040_FORMATS, }, .ops = &twl6040_dai_ops, +}, +{ + .name = "twl6040-vib", + .playback = { + .stream_name = "Vibra Playback", + .channels_min = 2, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_CONTINUOUS, + .formats = TWL6040_FORMATS, + }, + .ops = &twl6040_dai_ops, +}, };
#ifdef CONFIG_PM @@ -1502,8 +1530,8 @@ static struct snd_soc_codec_driver soc_codec_dev_twl6040 = {
static int __devinit twl6040_codec_probe(struct platform_device *pdev) { - return snd_soc_register_codec(&pdev->dev, - &soc_codec_dev_twl6040, &twl6040_dai, 1); + return snd_soc_register_codec(&pdev->dev, &soc_codec_dev_twl6040, + twl6040_dai, ARRAY_SIZE(twl6040_dai)); }
static int __devexit twl6040_codec_remove(struct platform_device *pdev)
From: Liam Girdwood lrg@ti.com
Add other supported sample rates to LP and HP modes.
Signed-off-by: Liam Girdwood lrg@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com --- sound/soc/codecs/twl6040.c | 11 +++++++++++ 1 files changed, 11 insertions(+), 0 deletions(-)
diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index 28dc5d9..7845cdb 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -1203,6 +1203,13 @@ static int twl6040_set_bias_level(struct snd_soc_codec *codec, /* set of rates for each pll: low-power and high-performance */
static unsigned int lp_rates[] = { + 8000, + 11250, + 16000, + 22500, + 32000, + 44100, + 48000, 88200, 96000, }; @@ -1213,6 +1220,10 @@ static struct snd_pcm_hw_constraint_list lp_constraints = { };
static unsigned int hp_rates[] = { + 8000, + 16000, + 32000, + 48000, 96000, };
From: Misael Lopez Cruz misael.lopez@ti.com
Remove dependency between pll (hppll, lppll) and headset power mode (low-power, high-performance), as headset power mode can be used with any pll.
A new control is created to allow headset power mode configuration from userspace. Changing headset power mode during earpiece related usecases is not propagated down to the codec as earpiece requires HS DAC in HP mode.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- sound/soc/codecs/twl6040.c | 62 ++++++++++++++++++++++++++++++++++++++++--- 1 files changed, 57 insertions(+), 5 deletions(-)
diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index 7845cdb..c8f7fc2 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -79,6 +79,8 @@ struct twl6040_data { int codec_powered; int pll; int non_lp; + int hs_power_mode; + int hs_power_mode_locked; unsigned int clk_in; unsigned int sysclk; struct snd_pcm_hw_constraint_list *sysclk_constraints; @@ -651,15 +653,26 @@ static int twl6040_power_mode_event(struct snd_soc_dapm_widget *w, { struct snd_soc_codec *codec = w->codec; struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); + int ret = 0;
- if (SND_SOC_DAPM_EVENT_ON(event)) + if (SND_SOC_DAPM_EVENT_ON(event)) { priv->non_lp++; - else + if (!strcmp(w->name, "Earphone Driver")) { + /* Earphone doesn't support low power mode */ + priv->hs_power_mode_locked = 1; + ret = headset_power_mode(codec, 1); + } + } else { priv->non_lp--; + if (!strcmp(w->name, "Earphone Driver")) { + priv->hs_power_mode_locked = 0; + ret = headset_power_mode(codec, priv->hs_power_mode); + } + }
msleep(1);
- return 0; + return ret; }
static void twl6040_hs_jack_report(struct snd_soc_codec *codec, @@ -964,6 +977,43 @@ static const struct snd_kcontrol_new hfr_mux_controls = static const struct snd_kcontrol_new ep_driver_switch_controls = SOC_DAPM_SINGLE("Switch", TWL6040_REG_EARCTL, 0, 1, 0);
+/* Headset power mode */ +static const char *twl6040_headset_power_texts[] = { + "Low-Power", "High-Perfomance", +}; + +static const struct soc_enum twl6040_headset_power_enum = + SOC_ENUM_SINGLE_EXT(ARRAY_SIZE(twl6040_headset_power_texts), + twl6040_headset_power_texts); + +static int twl6040_headset_power_get_enum(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); + + ucontrol->value.enumerated.item[0] = priv->hs_power_mode; + + return 0; +} + +static int twl6040_headset_power_put_enum(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); + struct twl6040_data *priv = snd_soc_codec_get_drvdata(codec); + int high_perf = ucontrol->value.enumerated.item[0]; + int ret = 0; + + if (!priv->hs_power_mode_locked) + ret = headset_power_mode(codec, high_perf); + + if (!ret) + priv->hs_power_mode = high_perf; + + return ret; +} + static const struct snd_kcontrol_new twl6040_snd_controls[] = { /* Capture gains */ SOC_DOUBLE_TLV("Capture Preamplifier Volume", @@ -982,6 +1032,10 @@ static const struct snd_kcontrol_new twl6040_snd_controls[] = { TWL6040_REG_HFLGAIN, TWL6040_REG_HFRGAIN, 0, 0x1D, 1, hf_tlv), SOC_SINGLE_TLV("Earphone Playback Volume", TWL6040_REG_EARCTL, 1, 0xF, 1, ep_tlv), + + SOC_ENUM_EXT("Headset Power Mode", twl6040_headset_power_enum, + twl6040_headset_power_get_enum, + twl6040_headset_power_put_enum), };
static const struct snd_soc_dapm_widget twl6040_dapm_widgets[] = { @@ -1339,7 +1393,6 @@ static int twl6040_set_dai_sysclk(struct snd_soc_dai *codec_dai, if (ret) return ret;
- headset_power_mode(codec, 0); priv->sysclk_constraints = &lp_constraints; break; case TWL6040_SYSCLK_SEL_HPPLL: @@ -1348,7 +1401,6 @@ static int twl6040_set_dai_sysclk(struct snd_soc_dai *codec_dai, if (ret) return ret;
- headset_power_mode(codec, 1); priv->sysclk_constraints = &hp_constraints; break; default:
On Tue, Jun 21, 2011 at 04:39:13PM +0300, Peter Ujfalusi wrote:
From: Misael Lopez Cruz misael.lopez@ti.com
Remove dependency between pll (hppll, lppll) and headset power mode (low-power, high-performance), as headset power mode can be used with any pll.
Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com
but you should note that the code has been modified since Misael's original version.
Hello Mark,
On Tuesday 21 June 2011 19:35:05 Mark Brown wrote:
On Tue, Jun 21, 2011 at 04:39:13PM +0300, Peter Ujfalusi wrote:
From: Misael Lopez Cruz misael.lopez@ti.com
Remove dependency between pll (hppll, lppll) and headset power mode (low-power, high-performance), as headset power mode can be used with any pll.
Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com
but you should note that the code has been modified since Misael's original version.
Oh. I did intended to put comments related to the changes has been done to this patch. Obviously I forgot to do that. I did not added your ack to this patch, since I knew that I have changed a bit more. Sorry.
From: Liam Girdwood lrg@ti.com
Set default sysclk constraints to high performance mode.
Signed-off-by: Liam Girdwood lrg@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com --- sound/soc/codecs/twl6040.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index c8f7fc2..39ecf2f 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -1502,6 +1502,7 @@ static int twl6040_probe(struct snd_soc_codec *codec) priv->codec = codec; codec->control_data = dev_get_drvdata(codec->dev->parent);
+ priv->sysclk_constraints = &hp_constraints; priv->workqueue = create_singlethread_workqueue("twl6040-codec"); if (!priv->workqueue) { ret = -ENOMEM;
From: Axel Castaneda Gonzalez x0055901@ti.com
Enable ramp down/up step to be configured based on platform.
Signed-off-by: Axel Castaneda Gonzalez x0055901@ti.com Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com --- include/linux/i2c/twl.h | 4 ++ sound/soc/codecs/twl6040.c | 91 ++++++++++++++++++++++++++++++++++---------- 2 files changed, 75 insertions(+), 20 deletions(-)
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h index 685fd76..114c0f6 100644 --- a/include/linux/i2c/twl.h +++ b/include/linux/i2c/twl.h @@ -664,6 +664,10 @@ struct twl4030_codec_data { unsigned int check_defaults:1; unsigned int reset_registers:1; unsigned int hs_extmute:1; + u16 hs_left_step; + u16 hs_right_step; + u16 hf_left_step; + u16 hf_right_step; void (*set_hs_extmute)(int mute); };
diff --git a/sound/soc/codecs/twl6040.c b/sound/soc/codecs/twl6040.c index 39ecf2f..0145041 100644 --- a/sound/soc/codecs/twl6040.c +++ b/sound/soc/codecs/twl6040.c @@ -83,6 +83,10 @@ struct twl6040_data { int hs_power_mode_locked; unsigned int clk_in; unsigned int sysclk; + u16 hs_left_step; + u16 hs_right_step; + u16 hf_left_step; + u16 hf_right_step; struct snd_pcm_hw_constraint_list *sysclk_constraints; struct twl6040_jack_data hs_jack; struct snd_soc_codec *codec; @@ -339,7 +343,11 @@ static inline int twl6040_hs_ramp_step(struct snd_soc_codec *codec, if (headset->ramp == TWL6040_RAMP_UP) { /* ramp step up */ if (val < headset->left_vol) { - val += left_step; + if (val + left_step > headset->left_vol) + val = headset->left_vol; + else + val += left_step; + reg &= ~TWL6040_HSL_VOL_MASK; twl6040_write(codec, TWL6040_REG_HSGAIN, (reg | (~val & TWL6040_HSL_VOL_MASK))); @@ -349,7 +357,11 @@ static inline int twl6040_hs_ramp_step(struct snd_soc_codec *codec, } else if (headset->ramp == TWL6040_RAMP_DOWN) { /* ramp step down */ if (val > 0x0) { - val -= left_step; + if ((int)val - (int)left_step < 0) + val = 0; + else + val -= left_step; + reg &= ~TWL6040_HSL_VOL_MASK; twl6040_write(codec, TWL6040_REG_HSGAIN, reg | (~val & TWL6040_HSL_VOL_MASK)); @@ -366,7 +378,11 @@ static inline int twl6040_hs_ramp_step(struct snd_soc_codec *codec, if (headset->ramp == TWL6040_RAMP_UP) { /* ramp step up */ if (val < headset->right_vol) { - val += right_step; + if (val + right_step > headset->right_vol) + val = headset->right_vol; + else + val += right_step; + reg &= ~TWL6040_HSR_VOL_MASK; twl6040_write(codec, TWL6040_REG_HSGAIN, (reg | (~val << TWL6040_HSR_VOL_SHIFT))); @@ -376,7 +392,11 @@ static inline int twl6040_hs_ramp_step(struct snd_soc_codec *codec, } else if (headset->ramp == TWL6040_RAMP_DOWN) { /* ramp step down */ if (val > 0x0) { - val -= right_step; + if ((int)val - (int)right_step < 0) + val = 0; + else + val -= right_step; + reg &= ~TWL6040_HSR_VOL_MASK; twl6040_write(codec, TWL6040_REG_HSGAIN, reg | (~val << TWL6040_HSR_VOL_SHIFT)); @@ -407,7 +427,11 @@ static inline int twl6040_hf_ramp_step(struct snd_soc_codec *codec, if (handsfree->ramp == TWL6040_RAMP_UP) { /* ramp step up */ if (val < handsfree->left_vol) { - val += left_step; + if (val + left_step > handsfree->left_vol) + val = handsfree->left_vol; + else + val += left_step; + reg &= ~TWL6040_HF_VOL_MASK; twl6040_write(codec, TWL6040_REG_HFLGAIN, reg | (0x1D - val)); @@ -417,7 +441,11 @@ static inline int twl6040_hf_ramp_step(struct snd_soc_codec *codec, } else if (handsfree->ramp == TWL6040_RAMP_DOWN) { /* ramp step down */ if (val > 0) { - val -= left_step; + if ((int)val - (int)left_step < 0) + val = 0; + else + val -= left_step; + reg &= ~TWL6040_HF_VOL_MASK; twl6040_write(codec, TWL6040_REG_HFLGAIN, reg | (0x1D - val)); @@ -434,7 +462,11 @@ static inline int twl6040_hf_ramp_step(struct snd_soc_codec *codec, if (handsfree->ramp == TWL6040_RAMP_UP) { /* ramp step up */ if (val < handsfree->right_vol) { - val += right_step; + if (val + right_step > handsfree->right_vol) + val = handsfree->right_vol; + else + val += right_step; + reg &= ~TWL6040_HF_VOL_MASK; twl6040_write(codec, TWL6040_REG_HFRGAIN, reg | (0x1D - val)); @@ -444,7 +476,11 @@ static inline int twl6040_hf_ramp_step(struct snd_soc_codec *codec, } else if (handsfree->ramp == TWL6040_RAMP_DOWN) { /* ramp step down */ if (val > 0) { - val -= right_step; + if ((int)val - (int)right_step < 0) + val = 0; + else + val -= right_step; + reg &= ~TWL6040_HF_VOL_MASK; twl6040_write(codec, TWL6040_REG_HFRGAIN, reg | (0x1D - val)); @@ -473,11 +509,9 @@ static void twl6040_pga_hs_work(struct work_struct *work)
/* HS PGA volumes have 4 bits of resolution to ramp */ for (i = 0; i <= 16; i++) { - headset_complete = 1; - if (headset->ramp != TWL6040_RAMP_NONE) - headset_complete = twl6040_hs_ramp_step(codec, - headset->left_step, - headset->right_step); + headset_complete = twl6040_hs_ramp_step(codec, + headset->left_step, + headset->right_step);
/* ramp finished ? */ if (headset_complete) @@ -518,11 +552,9 @@ static void twl6040_pga_hf_work(struct work_struct *work)
/* HF PGA volumes have 5 bits of resolution to ramp */ for (i = 0; i <= 32; i++) { - handsfree_complete = 1; - if (handsfree->ramp != TWL6040_RAMP_NONE) - handsfree_complete = twl6040_hf_ramp_step(codec, - handsfree->left_step, - handsfree->right_step); + handsfree_complete = twl6040_hf_ramp_step(codec, + handsfree->left_step, + handsfree->right_step);
/* ramp finished ? */ if (handsfree_complete) @@ -563,12 +595,16 @@ static int pga_event(struct snd_soc_dapm_widget *w, out = &priv->headset; work = &priv->hs_delayed_work; queue = priv->hs_workqueue; + out->left_step = priv->hs_left_step; + out->right_step = priv->hs_right_step; out->step_delay = 5; /* 5 ms between volume ramp steps */ break; case 4: out = &priv->handsfree; work = &priv->hf_delayed_work; queue = priv->hf_workqueue; + out->left_step = priv->hf_left_step; + out->right_step = priv->hf_right_step; out->step_delay = 5; /* 5 ms between volume ramp steps */ if (SND_SOC_DAPM_EVENT_ON(event)) priv->non_lp++; @@ -601,8 +637,6 @@ static int pga_event(struct snd_soc_dapm_widget *w,
if (!delayed_work_pending(work)) { /* use volume ramp for power-down */ - out->left_step = 1; - out->right_step = 1; out->ramp = TWL6040_RAMP_DOWN; INIT_COMPLETION(out->ramp_done);
@@ -1492,6 +1526,7 @@ static int twl6040_resume(struct snd_soc_codec *codec) static int twl6040_probe(struct snd_soc_codec *codec) { struct twl6040_data *priv; + struct twl4030_codec_data *pdata = dev_get_platdata(codec->dev); int ret = 0;
priv = kzalloc(sizeof(struct twl6040_data), GFP_KERNEL); @@ -1502,6 +1537,22 @@ static int twl6040_probe(struct snd_soc_codec *codec) priv->codec = codec; codec->control_data = dev_get_drvdata(codec->dev->parent);
+ if (pdata && pdata->hs_left_step && pdata->hs_right_step) { + priv->hs_left_step = pdata->hs_left_step; + priv->hs_right_step = pdata->hs_right_step; + } else { + priv->hs_left_step = 1; + priv->hs_right_step = 1; + } + + if (pdata && pdata->hf_left_step && pdata->hf_right_step) { + priv->hf_left_step = pdata->hf_left_step; + priv->hf_right_step = pdata->hf_right_step; + } else { + priv->hf_left_step = 1; + priv->hf_right_step = 1; + } + priv->sysclk_constraints = &hp_constraints; priv->workqueue = create_singlethread_workqueue("twl6040-codec"); if (!priv->workqueue) {
From: Misael Lopez Cruz misael.lopez@ti.com
Configure, and enable the twl6040 codec on SDP4430.
Signed-off-by: Misael Lopez Cruz misael.lopez@ti.com Signed-off-by: Peter Ujfalusi peter.ujfalusi@ti.com --- arch/arm/mach-omap2/board-4430sdp.c | 10 +++++++++- 1 files changed, 9 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index 266d146..369250b 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -432,6 +432,14 @@ static struct regulator_init_data sdp4430_vusim = { }, };
+static struct twl4030_codec_data twl6040_codec = { + /* single-step ramp for headset and handsfree */ + .hs_left_step = 0x0f, + .hs_right_step = 0x0f, + .hf_left_step = 0x1d, + .hf_right_step = 0x1d, +}; + static struct twl4030_vibra_data twl6040_vibra = { .vibldrv_res = 8, .vibrdrv_res = 3, @@ -442,7 +450,7 @@ static struct twl4030_vibra_data twl6040_vibra = { };
static struct twl4030_audio_data twl6040_audio = { - .codec = NULL, + .codec = &twl6040_codec, .vibra = &twl6040_vibra, .audpwron_gpio = 127, .naudint_irq = OMAP44XX_IRQ_SYS_2N,
Hi Tony, Samuel,
Would you have time to take a look at this series?
Thanks, Péter
On Tuesday 21 June 2011 15:38:58 Ujfalusi, Peter wrote:
Hello,
Changes since v5:
- Use alloc_workqueue in the twl6040-vibra driver (comment from Tejun Heo)
- Allow user to change the headset power mode, but if the change is not
allowed by the use case the change is not written to the HW (comment from Mark Brown)
Mark: I have added your acks for the patches, except for patch 15, where you requested a change.
Intro message from the v5 series: The series will do five major things, and they are in one series, because they pretty much depending on each other, so it is easier to handle them together.
- Move the common pmic related configurations out from the board files.
New twl-common.c/h file has been created for this purpose. OMAP3 board files received two patches (pdata, and regualtor changes), OMAP4 board files has been changed with one patch.
- Rename the twl4030-codec MFD driver to twl4030-audio
Since the ASoC multicomponent introduction (2.6.37) the twl4030-codec MFD dirver had been using twl4030-audio to register (twl4030-codec is the ASoC codec driver). The documentation refers to this part of twl as audio block, so it is better to rename the driver as well to avoid confusion.
- Introduction of MFD driver for twl6040.
The TWL6040 audio IC has codec and vibra functionality. Convert the existing ASoC codec driver to use the new MFD driver's interface.
- Vibrator driver for TWL6040 (Input/ForceFeedback driver)
The driver itself, and support for the vibrators in SDP4430 board.
- Updates for twl6040 ASoC codec driver
HS ramp configuration, new ABE dais, updated sample rate constraints, SDP4430 configuration.
Regards, Peter
Axel Castaneda Gonzalez (1): ASoC: twl6040: Configure ramp step based on platform
Liam Girdwood (3): ASoC: twl6040: add all ABE DAIs ASoC: twl6040: Support other sample rates in constraints. ASoC: twl6040: set default constraints.
Misael Lopez Cruz (5): mfd: twl6040: Add initial support ASoC: twl6040: Convert into TWL6040 MFD child input: Add initial support for TWL6040 vibrator ASoC: twl6040: Remove pll and headset mode dependency OMAP4: SDP4430: Add twl6040 codec platform support
Peter Ujfalusi (9): OMAP: New twl-common for common TWL configuration OMAP4: Move common twl6030 configuration to twl-common OMAP3: Move common twl configuration to twl-common OMAP3: Move common regulator configuration to twl-common MFD: twl4030-codec: Rename internals from codec to audio MFD: twl4030-codec -> twl4030-audio: Rename the driver MFD: twl4030-audio: Rename platform data MFD: twl6040: Change platform data for soc codec driver OMAP4: SDP4430: Add twl6040 vibrator platform support
arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/board-3430sdp.c | 89 +--- arch/arm/mach-omap2/board-4430sdp.c | 187 ++---- arch/arm/mach-omap2/board-cm-t35.c | 48 +-- arch/arm/mach-omap2/board-devkit8000.c | 37 +-- arch/arm/mach-omap2/board-igep0020.c | 44 +-- arch/arm/mach-omap2/board-ldp.c | 15 +- arch/arm/mach-omap2/board-omap3beagle.c | 60 +-- arch/arm/mach-omap2/board-omap3evm.c | 67 +-- arch/arm/mach-omap2/board-omap3pandora.c | 59 +-- arch/arm/mach-omap2/board-omap3stalker.c | 70 +-- arch/arm/mach-omap2/board-omap3touchbook.c | 57 +-- arch/arm/mach-omap2/board-omap4panda.c | 149 +----- arch/arm/mach-omap2/board-overo.c | 59 +-- arch/arm/mach-omap2/board-rm680.c | 8 +- arch/arm/mach-omap2/board-rx51-peripherals.c | 44 +-- arch/arm/mach-omap2/board-zoom-peripherals.c | 88 +--- arch/arm/mach-omap2/common-board-devices.c | 21 - arch/arm/mach-omap2/common-board-devices.h | 26 +- arch/arm/mach-omap2/twl-common.c | 304 ++++++++++ arch/arm/mach-omap2/twl-common.h | 59 ++ arch/arm/plat-omap/include/plat/irqs.h | 12 +- drivers/input/misc/Kconfig | 13 +- drivers/input/misc/Makefile | 1 + drivers/input/misc/twl4030-vibra.c | 12 +- drivers/input/misc/twl6040-vibra.c | 416 +++++++++++++ drivers/mfd/Kconfig | 8 +- drivers/mfd/Makefile | 3 +- drivers/mfd/twl-core.c | 13 +- drivers/mfd/twl4030-audio.c | 277 +++++++++ drivers/mfd/twl4030-codec.c | 277 --------- drivers/mfd/twl6040-core.c | 601 +++++++++++++++++++ drivers/mfd/twl6040-irq.c | 205 +++++++ include/linux/i2c/twl.h | 25 +- .../linux/mfd/{twl4030-codec.h => twl4030-audio.h} | 16 +- include/linux/mfd/twl6040.h | 261 ++++++++ sound/soc/codecs/Kconfig | 3 +- sound/soc/codecs/twl4030.c | 22 +- sound/soc/codecs/twl6040.c | 628 ++++++++------------ sound/soc/codecs/twl6040.h | 118 ---- sound/soc/omap/sdp3430.c | 2 +- sound/soc/omap/sdp4430.c | 2 + sound/soc/omap/zoom2.c | 2 +- 43 files changed, 2635 insertions(+), 1775 deletions(-) create mode 100644 arch/arm/mach-omap2/twl-common.c create mode 100644 arch/arm/mach-omap2/twl-common.h create mode 100644 drivers/input/misc/twl6040-vibra.c create mode 100644 drivers/mfd/twl4030-audio.c delete mode 100644 drivers/mfd/twl4030-codec.c create mode 100644 drivers/mfd/twl6040-core.c create mode 100644 drivers/mfd/twl6040-irq.c rename include/linux/mfd/{twl4030-codec.h => twl4030-audio.h} (96%) create mode 100644 include/linux/mfd/twl6040.h
* Péter Ujfalusi peter.ujfalusi@ti.com [110627 02:39]:
Hi Tony, Samuel,
Would you have time to take a look at this series?
Looks good to me. If it conflicts with what we have queued in the devel-cleanup branch, I should probably queue it.
If there are no conflicts, then Samuel can queue it.
Regards,
Tony
Hi Tony,
On Monday 27 June 2011 12:18:35 Tony Lindgren wrote:
- Péter Ujfalusi peter.ujfalusi@ti.com [110627 02:39]:
Hi Tony, Samuel,
Would you have time to take a look at this series?
Looks good to me. If it conflicts with what we have queued in the devel-cleanup branch, I should probably queue it.
There are conflicts in mach-omap2 (quite a lot), if I apply the series on top of the devel-cleanup branch.
If there are no conflicts, then Samuel can queue it.
I suppose this should then go through l-o...
* Péter Ujfalusi peter.ujfalusi@ti.com [110627 07:25]:
Hi Tony,
On Monday 27 June 2011 12:18:35 Tony Lindgren wrote:
- Péter Ujfalusi peter.ujfalusi@ti.com [110627 02:39]:
Hi Tony, Samuel,
Would you have time to take a look at this series?
Looks good to me. If it conflicts with what we have queued in the devel-cleanup branch, I should probably queue it.
There are conflicts in mach-omap2 (quite a lot), if I apply the series on top of the devel-cleanup branch.
If there are no conflicts, then Samuel can queue it.
I suppose this should then go through l-o...
OK. Assuming Samuel is fine with the patches, care to put together a branch against devel-cleanup for me to pull?
Regards,
Tony
Hi Tony,
On Tuesday 28 June 2011 08:17:21 Tony Lindgren wrote:
OK. Assuming Samuel is fine with the patches, care to put together a branch against devel-cleanup for me to pull?
While waiting for Samuel, I can start preparing the branch for you, since the bulk of the conflicts are in mach-omap2, should not affect the MFD parts. Can I add your ack to the mach-omap2 parts, or are you prefer to handle this yourself?
* Péter Ujfalusi peter.ujfalusi@ti.com [110627 23:39]:
Hi Tony,
On Tuesday 28 June 2011 08:17:21 Tony Lindgren wrote:
OK. Assuming Samuel is fine with the patches, care to put together a branch against devel-cleanup for me to pull?
While waiting for Samuel, I can start preparing the branch for you, since the bulk of the conflicts are in mach-omap2, should not affect the MFD parts. Can I add your ack to the mach-omap2 parts, or are you prefer to handle this yourself?
OK here you go for the omap changes:
Acked-by: Tony Lindgren tony@atomide.com
Hi Samuel,
Would you be able to take a look at this series? I already have the rebased version on top of linux-omap/devel-cleanup branch as Tony requested, and I'm now waiting for your comments.
Thank you, Péter
On Monday 27 June 2011 11:43:57 Ujfalusi, Peter wrote:
Hi Tony, Samuel,
Would you have time to take a look at this series?
Thanks, Péter
On Tuesday 21 June 2011 15:38:58 Ujfalusi, Peter wrote:
Hello,
Changes since v5:
- Use alloc_workqueue in the twl6040-vibra driver (comment from Tejun
Heo) - Allow user to change the headset power mode, but if the change is not allowed by the use case the change is not written to the HW (comment from Mark Brown)
Mark: I have added your acks for the patches, except for patch 15, where you requested a change.
Intro message from the v5 series: The series will do five major things, and they are in one series, because they pretty much depending on each other, so it is easier to handle them together.
- Move the common pmic related configurations out from the board files.
New twl-common.c/h file has been created for this purpose. OMAP3 board files received two patches (pdata, and regualtor changes), OMAP4 board files has been changed with one patch.
- Rename the twl4030-codec MFD driver to twl4030-audio
Since the ASoC multicomponent introduction (2.6.37) the twl4030-codec MFD dirver had been using twl4030-audio to register (twl4030-codec is the ASoC codec driver). The documentation refers to this part of twl as audio block, so it is better to rename the driver as well to avoid confusion.
- Introduction of MFD driver for twl6040.
The TWL6040 audio IC has codec and vibra functionality. Convert the existing ASoC codec driver to use the new MFD driver's interface.
- Vibrator driver for TWL6040 (Input/ForceFeedback driver)
The driver itself, and support for the vibrators in SDP4430 board.
- Updates for twl6040 ASoC codec driver
HS ramp configuration, new ABE dais, updated sample rate constraints, SDP4430 configuration.
Regards, Peter
Axel Castaneda Gonzalez (1): ASoC: twl6040: Configure ramp step based on platform
Liam Girdwood (3): ASoC: twl6040: add all ABE DAIs ASoC: twl6040: Support other sample rates in constraints. ASoC: twl6040: set default constraints.
Misael Lopez Cruz (5): mfd: twl6040: Add initial support ASoC: twl6040: Convert into TWL6040 MFD child input: Add initial support for TWL6040 vibrator ASoC: twl6040: Remove pll and headset mode dependency OMAP4: SDP4430: Add twl6040 codec platform support
Peter Ujfalusi (9): OMAP: New twl-common for common TWL configuration OMAP4: Move common twl6030 configuration to twl-common OMAP3: Move common twl configuration to twl-common OMAP3: Move common regulator configuration to twl-common MFD: twl4030-codec: Rename internals from codec to audio MFD: twl4030-codec -> twl4030-audio: Rename the driver MFD: twl4030-audio: Rename platform data MFD: twl6040: Change platform data for soc codec driver OMAP4: SDP4430: Add twl6040 vibrator platform support
arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/board-3430sdp.c | 89 +--- arch/arm/mach-omap2/board-4430sdp.c | 187 ++---- arch/arm/mach-omap2/board-cm-t35.c | 48 +-- arch/arm/mach-omap2/board-devkit8000.c | 37 +-- arch/arm/mach-omap2/board-igep0020.c | 44 +-- arch/arm/mach-omap2/board-ldp.c | 15 +- arch/arm/mach-omap2/board-omap3beagle.c | 60 +-- arch/arm/mach-omap2/board-omap3evm.c | 67 +-- arch/arm/mach-omap2/board-omap3pandora.c | 59 +-- arch/arm/mach-omap2/board-omap3stalker.c | 70 +-- arch/arm/mach-omap2/board-omap3touchbook.c | 57 +-- arch/arm/mach-omap2/board-omap4panda.c | 149 +----- arch/arm/mach-omap2/board-overo.c | 59 +-- arch/arm/mach-omap2/board-rm680.c | 8 +- arch/arm/mach-omap2/board-rx51-peripherals.c | 44 +-- arch/arm/mach-omap2/board-zoom-peripherals.c | 88 +--- arch/arm/mach-omap2/common-board-devices.c | 21 - arch/arm/mach-omap2/common-board-devices.h | 26 +- arch/arm/mach-omap2/twl-common.c | 304 ++++++++++ arch/arm/mach-omap2/twl-common.h | 59 ++ arch/arm/plat-omap/include/plat/irqs.h | 12 +- drivers/input/misc/Kconfig | 13 +- drivers/input/misc/Makefile | 1 + drivers/input/misc/twl4030-vibra.c | 12 +- drivers/input/misc/twl6040-vibra.c | 416 +++++++++++++ drivers/mfd/Kconfig | 8 +- drivers/mfd/Makefile | 3 +- drivers/mfd/twl-core.c | 13 +- drivers/mfd/twl4030-audio.c | 277 +++++++++ drivers/mfd/twl4030-codec.c | 277 --------- drivers/mfd/twl6040-core.c | 601
+++++++++++++++++++ drivers/mfd/twl6040-irq.c | 205 +++++++ include/linux/i2c/twl.h | 25 +-
.../linux/mfd/{twl4030-codec.h => twl4030-audio.h} | 16 +- include/linux/mfd/twl6040.h | 261 ++++++++ sound/soc/codecs/Kconfig | 3 +- sound/soc/codecs/twl4030.c | 22 +- sound/soc/codecs/twl6040.c | 628
++++++++------------ sound/soc/codecs/twl6040.h | 118 ----
sound/soc/omap/sdp3430.c | 2 +- sound/soc/omap/sdp4430.c | 2 + sound/soc/omap/zoom2.c | 2 +- 43 files changed, 2635 insertions(+), 1775 deletions(-) create mode 100644 arch/arm/mach-omap2/twl-common.c create mode 100644 arch/arm/mach-omap2/twl-common.h create mode 100644 drivers/input/misc/twl6040-vibra.c create mode 100644 drivers/mfd/twl4030-audio.c delete mode 100644 drivers/mfd/twl4030-codec.c create mode 100644 drivers/mfd/twl6040-core.c create mode 100644 drivers/mfd/twl6040-irq.c rename include/linux/mfd/{twl4030-codec.h => twl4030-audio.h} (96%) create mode 100644 include/linux/mfd/twl6040.h
Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
participants (4)
-
Dmitry Torokhov
-
Mark Brown
-
Peter Ujfalusi
-
Tony Lindgren