From: Chris Morgan macromorgan@hotmail.com

Enable support for 12Mhz sysclk on es8328. This sysclk value is used on the Indiedroid Nova rk3588s based single board computer.

Signed-off-by: Chris Morgan macromorgan@hotmail.com Signed-off-by: Chris Zhong zyw@rock-chips.com --- sound/soc/codecs/es8328.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)

diff --git a/sound/soc/codecs/es8328.c b/sound/soc/codecs/es8328.c index 160adc706cc6..3918be5fc3f1 100644 --- a/sound/soc/codecs/es8328.c +++ b/sound/soc/codecs/es8328.c @@ -36,6 +36,16 @@ static const struct snd_pcm_hw_constraint_list constraints_12288 = { .list = rates_12288, };

+static unsigned int ratios_12000[] = { + 8000, 11025, 12000, 16000, 22050, 24000, 32000, 44100, 48000, + 48000, 88235, 96000, +}; + +static struct snd_pcm_hw_constraint_list constraints_12000 = { + .count = ARRAY_SIZE(ratios_12000), + .list = ratios_12000, +}; + static const unsigned int rates_11289[] = { 8018, 11025, 22050, 44100, 88200, }; @@ -577,6 +587,13 @@ static int es8328_set_sysclk(struct snd_soc_dai *codec_dai, es8328->sysclk_constraints = &constraints_12288; es8328->mclk_ratios = ratios_12288; break; + case 24000000: + mclkdiv2 = 1; + fallthrough; + case 12000000: + es8328->sysclk_constraints = &constraints_12000; + es8328->mclk_ratios = ratios_12000; + break; default: return -EINVAL; }

From: Chris Morgan macromorgan@hotmail.com

Add SDIO node for rk3588/rk3588s.

Signed-off-by: Chris Morgan macromorgan@hotmail.com --- arch/arm64/boot/dts/rockchip/rk3588s.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi index 571cdec24a66..6335d5648bc3 100644 --- a/arch/arm64/boot/dts/rockchip/rk3588s.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3588s.dtsi @@ -1176,6 +1176,21 @@ sdmmc: mmc@fe2c0000 { status = "disabled"; };

+ sdio: mmc@fe2d0000 { + compatible = "rockchip,rk3588-dw-mshc", "rockchip,rk3288-dw-mshc"; + reg = <0x00 0xfe2d0000 0x00 0x4000>; + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&cru HCLK_SDIO>, <&cru CCLK_SRC_SDIO>, + <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; + clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; + fifo-depth = <0x100>; + max-frequency = <200000000>; + pinctrl-names = "default"; + pinctrl-0 = <&sdiom1_pins>; + power-domains = <&power RK3588_PD_SDIO>; + status = "disabled"; + }; + sdhci: mmc@fe2e0000 { compatible = "rockchip,rk3588-dwcmshc"; reg = <0x0 0xfe2e0000 0x0 0x10000>;

From: Chris Morgan macromorgan@hotmail.com

Add Indiedroid Nova, an rk3588s based single board computer.

Signed-off-by: Chris Morgan macromorgan@hotmail.com --- Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml index ec141c937b8b..3c5a204bcd81 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.yaml +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml @@ -542,6 +542,11 @@ properties: - khadas,edge-v - const: rockchip,rk3399

+ - description: Indiedroid Nova SBC + items: + - const: indiedroid,nova + - const: rockchip,rk3588s + - description: Khadas Edge2 series boards items: - const: khadas,edge2

From: Chris Morgan macromorgan@hotmail.com

The Indiedroid Nova is an SBC from a sub-brand of Ameridroid that includes the following hardware:

- A 40-pin GPIO header - 2 USB-A 3.0 ports - 2 USB-A 2.0 ports - A USB-C 2.0 OTG port (used for USB power delivery) - A USB-C 3.0 port that can do display port output. - A Micro HDMI 2.1 port. - A 1GB ethernet port. - An RT8821CS based WiFi/Bluetooth module. - A user replaceable eMMC module. - An SDMMC card slot. - A MIPI DSI connector. - A MIPI CSI connector. - A 3.5mm TRRS audio jack with microphone input. - An 2 pin socket for an RTC battery. - A 4 pin socket for a debug port. - A power button (connected to PMIC), a reset button (connected to SoC reset), a boot button, and a recovery button (both connected to the ADC). - 4GB, 8GB, or 16GB of system RAM.

This initial devicetree includes support for the WiFi, bluetooth, analog audio out/in, SDMMC, eMMC, RTC, UART debugging, and has the regulator values from the schematics. ADC, graphics output, GPU, USB, and wired ethernet are still pending additional upstream changes.

Signed-off-by: Chris Morgan macromorgan@hotmail.com --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../dts/rockchip/rk3588s-indiedroid-nova.dts | 761 ++++++++++++++++++ 2 files changed, 762 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile index 2d585bbb8f3a..99f11db8158d 100644 --- a/arch/arm64/boot/dts/rockchip/Makefile +++ b/arch/arm64/boot/dts/rockchip/Makefile @@ -94,5 +94,6 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts b/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts new file mode 100644 index 000000000000..b7070dd970e6 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts @@ -0,0 +1,761 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/usb/pd.h> +#include "rk3588s.dtsi" + +/ { + model = "Indiedroid Nova"; + compatible = "indiedroid,nova", "rockchip,rk3588s"; + + aliases { + mmc0 = &sdhci; + mmc1 = &sdmmc; + mmc2 = &sdio; + serial2 = &uart2; + }; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + clock-names = "ext_clock"; + clocks = <&rtc_hym8563>; + pinctrl-0 = <&wifi_enable_h>; + pinctrl-names = "default"; + post-power-on-delay-ms = <200>; + reset-gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>; + }; + + sound { + compatible = "audio-graph-card"; + label = "rockchip,es8388-codec"; + widgets = "Microphone", "Mic Jack", + "Headphone", "Headphones"; + routing = "LINPUT2", "Mic Jack", + "Headphones", "LOUT1", + "Headphones", "ROUT1"; + dais = <&i2s0_8ch_p0>; + }; + + vbus5v0_typec: vbus5v0-typec { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&typec5v_pwren>; + pinctrl-names = "default"; + regulator-name = "vbus5v0_typec"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v0_usb>; + }; + + vcc_1v1_nldo_s3: vcc-1v1-nldo-s3 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1100000>; + regulator-min-microvolt = <1100000>; + regulator-name = "vcc_1v1_nldo_s3"; + vin-supply = <&vcc5v0_sys>; + }; + + /* Regulator is enabled whenever vcc_1v8_s0 is above 1.6v */ + vcc_3v3_s0: vcc-3v3-s0 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "vcc_3v3_s0"; + vin-supply = <&vcc_3v3_s3>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc5v0_sys: vcc5v0-sys { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "vcc5v0_sys"; + }; + + vcc5v0_usb: vcc5v0-usb { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "vcc5v0_usb"; + vin-supply = <&vcc5v0_usbdcin>; + }; + + vcc5v0_usbdcin: vcc5v0-usbdcin { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "vcc5v0_usbdcin"; + }; +}; + +&cpu_l0 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_l1 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_l2 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_l3 { + cpu-supply = <&vdd_cpu_lit_s0>; +}; + +&cpu_b0{ + cpu-supply = <&vdd_cpu_big0_s0>; +}; + +&cpu_b1{ + cpu-supply = <&vdd_cpu_big0_s0>; +}; + +&cpu_b2{ + cpu-supply = <&vdd_cpu_big1_s0>; +}; + +&cpu_b3{ + cpu-supply = <&vdd_cpu_big1_s0>; +}; + +/* + * Add labels for each GPIO pin exposed on the 40 pin header. Note that + * voltage of each GPIO pin could be either 3.3v or 1.8v (as noted by + * label). + */ +&gpio0 { + gpio-line-names = /* GPIO0 A0-A7 */ + "", "", "", "", + "", "", "", "", + /* GPIO0 B0-B7 */ + "", "", "", "", + "", "", "", "", + /* GPIO0 C0-C7 */ + "", "", "", "", + "", "", "", "", + /* GPIO0 D0-D7 */ + "HEADER_12_1v8", "", "", "HEADER_24_1v8", + "", "", "", ""; +}; + +&gpio1 { + gpio-line-names = /* GPIO1 A0-A7 */ + "HEADER_27_3v3", "HEADER_28_3v3", "", "", + "HEADER_29_1v8", "", "HEADER_7_1v8", "", + /* GPIO1 B0-B7 */ + "", "HEADER_31_1v8", "HEADER_33_1v8", "", + "HEADER_11_1v8", "HEADER_13_1v8", "", "", + /* GPIO1 C0-C7 */ + "", "", "", "", + "", "", "", "", + /* GPIO1 D0-D7 */ + "", "", "", "", + "", "", "HEADER_5_3v3", "HEADER_3_3v3"; +}; + +&gpio3 { + gpio-line-names = /* GPIO3 A0-A7 */ + "", "", "", "", + "", "", "", "", + /* GPIO3 B0-B7 */ + "HEADER_16_1v8", "HEADER_18_1v8", "", "", + "", "", "", "HEADER_19_1v8", + /* GPIO3 C0-C7 */ + "HEADER_21_1v8", "HEADER_23_1v8", "", "HEADER_26_1v8", + "HEADER_15_1v8", "HEADER_22_1v8", "", "", + /* GPIO3 D0-D7 */ + "", "", "", "", + "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = /* GPIO4 A0-A7 */ + "", "", "HEADER_37_3v3", "HEADER_32_3v3", + "HEADER_36_3v3", "", "HEADER_35_3v3", "HEADER_38_3v3", + /* GPIO4 B0-B7 */ + "", "", "", "HEADER_40_3v3", + "HEADER_8_3v3", "HEADER_10_3v3", "", "", + /* GPIO4 C0-C7 */ + "", "", "", "", + "", "", "", "", + /* GPIO4 D0-D7 */ + "", "", "", "", + "", "", "", ""; +}; + +&i2c0 { + pinctrl-0 = <&i2c0m2_xfer>; + pinctrl-names = "default"; + status = "okay"; + + vdd_cpu_big0_s0: regulator@42 { + compatible = "rockchip,rk8602"; + reg = <0x42>; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1050000>; + regulator-min-microvolt = <550000>; + regulator-name = "vdd_cpu_big0_s0"; + regulator-ramp-delay = <2300>; + fcs,suspend-voltage-selector = <1>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_cpu_big1_s0: regulator@43 { + compatible = "rockchip,rk8603", "rockchip,rk8602"; + reg = <0x43>; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1050000>; + regulator-min-microvolt = <550000>; + regulator-name = "vdd_cpu_big1_s0"; + regulator-ramp-delay = <2300>; + fcs,suspend-voltage-selector = <1>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; +}; + +&i2c2 { + status = "okay"; + + vdd_npu_s0: regulator@42 { + compatible = "rockchip,rk8602"; + reg = <0x42>; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <950000>; + regulator-min-microvolt = <550000>; + regulator-name = "vdd_npu_s0"; + regulator-ramp-delay = <2300>; + fcs,suspend-voltage-selector = <1>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; +}; + +&i2c6 { + pinctrl-0 = <&i2c6m3_xfer>; + status = "okay"; + + fusb302: typec-portc@22 { + compatible = "fcs,fusb302"; + reg = <0x22>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PC4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&usbc0_int>; + pinctrl-names = "default"; + vbus-supply = <&vbus5v0_typec>; + + connector { + compatible = "usb-c-connector"; + data-role = "dual"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>; + op-sink-microwatt = <1000000>; + }; + }; + + rtc_hym8563: rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-output-names = "hym8563"; + interrupt-parent = <&gpio0>; + interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&hym8563_int>; + pinctrl-names = "default"; + wakeup-source; + }; +}; + +&i2c7 { + pinctrl-0 = <&i2c7m0_xfer>; + status = "okay"; + + es8388: audio-codec@11 { + compatible = "everest,es8388"; + reg = <0x11>; + AVDD-supply = <&vcc_3v3_s3>; + clock-names = "mclk"; + clocks = <&cru I2S0_8CH_MCLKOUT>; + DVDD-supply = <&vcc_1v8_s3>; + HPVDD-supply = <&vcc_3v3_s3>; + PVDD-supply = <&vcc_1v8_s3>; + #sound-dai-cells = <0>; + + port { + es8388_p0_0: endpoint { + remote-endpoint = <&i2s0_8ch_p0_0>; + }; + }; + }; +}; + +&i2s0_8ch { + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_lrck + &i2s0_mclk + &i2s0_sclk + &i2s0_sdi0 + &i2s0_sdo0>; + status = "okay"; + + i2s0_8ch_p0: port { + i2s0_8ch_p0_0: endpoint { + dai-format = "i2s"; + mclk-fs = <256>; + remote-endpoint = <&es8388_p0_0>; + }; + }; +}; + + +&pinctrl { + bluetooth-pins { + bt_reset: bt-reset { + rockchip,pins = + <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_dev: bt-wake-dev { + rockchip,pins = + <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + bt_wake_host: bt-wake-host { + rockchip,pins = + <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + hym8563 { + + hym8563_int: hym8563-int { + rockchip,pins = + <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + sdio-pwrseq { + wifi_enable_h: wifi-enable-h { + rockchip,pins = + <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb-typec { + usbc0_int: usbc0-int { + rockchip,pins = + <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + + typec5v_pwren: typec5v-pwren { + rockchip,pins = + <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +/* HS400 modes seemed to cause io errors. */ +&sdhci { + bus-width = <8>; + no-mmc-hs400; + no-sd; + no-sdio; + non-removable; + max-frequency = <200000000>; + vmmc-supply = <&vcc_3v3_s0>; + vqmmc-supply = <&vcc_1v8_s3>; + status = "okay"; +}; + +&sdio { + bus-width = <4>; + cap-sd-highspeed; + cap-sdio-irq; + disable-wp; + keep-power-in-suspend; + max-frequency = <100000000>; + mmc-pwrseq = <&sdio_pwrseq>; + no-mmc; + no-sd; + non-removable; + sd-uhs-sdr104; + vmmc-supply = <&vcc_3v3_s3>; + vqmmc-supply = <&vcc_1v8_s3>; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + max-frequency = <200000000>; + no-sdio; + no-mmc; + sd-uhs-sdr104; + vmmc-supply = <&vcc_3v3_s3>; + vqmmc-supply = <&vccio_sd_s0>; + status = "okay"; +}; + +&spi2 { + #address-cells = <1>; + assigned-clocks = <&cru CLK_SPI2>; + assigned-clock-rates = <200000000>; + pinctrl-0 = <&spi2m2_pins>, <&spi2m2_cs0>; + pinctrl-names = "default"; + #size-cells = <0>; + status = "okay"; + + pmic@0 { + compatible = "rockchip,rk806"; + reg = <0x0>; + #gpio-cells = <2>; + gpio-controller; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, + <&rk806_dvs2_null>, <&rk806_dvs3_null>; + pinctrl-names = "default"; + spi-max-frequency = <1000000>; + + vcc1-supply = <&vcc5v0_sys>; + vcc2-supply = <&vcc5v0_sys>; + vcc3-supply = <&vcc5v0_sys>; + vcc4-supply = <&vcc5v0_sys>; + vcc5-supply = <&vcc5v0_sys>; + vcc6-supply = <&vcc5v0_sys>; + vcc7-supply = <&vcc5v0_sys>; + vcc8-supply = <&vcc5v0_sys>; + vcc9-supply = <&vcc5v0_sys>; + vcc10-supply = <&vcc5v0_sys>; + vcc11-supply = <&vcc_2v0_pldo_s3>; + vcc12-supply = <&vcc5v0_sys>; + vcc13-supply = <&vcc_1v1_nldo_s3>; + vcc14-supply = <&vcc_1v1_nldo_s3>; + vcca-supply = <&vcc5v0_sys>; + + rk806_dvs1_null: dvs1-null-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun0"; + }; + + rk806_dvs2_null: dvs2-null-pins { + pins = "gpio_pwrctrl2"; + function = "pin_fun0"; + }; + + rk806_dvs3_null: dvs3-null-pins { + pins = "gpio_pwrctrl3"; + function = "pin_fun0"; + }; + + regulators { + vdd_gpu_s0: dcdc-reg1 { + regulator-boot-on; + regulator-enable-ramp-delay = <400>; + regulator-max-microvolt = <950000>; + regulator-min-microvolt = <550000>; + regulator-name = "vdd_gpu_s0"; + regulator-ramp-delay = <12500>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_cpu_lit_s0: dcdc-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <950000>; + regulator-min-microvolt = <550000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_cpu_lit_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_logic_s0: dcdc-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <750000>; + regulator-min-microvolt = <675000>; + regulator-name = "vdd_logic_s0"; + regulator-ramp-delay = <12500>; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <750000>; + }; + }; + + vdd_vdenc_s0: dcdc-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <950000>; + regulator-min-microvolt = <550000>; + regulator-name = "vdd_vdenc_s0"; + regulator-ramp-delay = <12500>; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_ddr_s0: dcdc-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <850000>; + regulator-ramp-delay = <12500>; + regulator-name = "vdd_ddr_s0"; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <850000>; + }; + }; + + vdd2_ddr_s3: dcdc-reg6 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1100000>; + regulator-min-microvolt = <1100000>; + regulator-name = "vdd2_ddr_s3"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_2v0_pldo_s3: dcdc-reg7 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <2000000>; + regulator-min-microvolt = <2000000>; + regulator-name = "vdd_2v0_pldo_s3"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <2000000>; + }; + }; + + vcc_3v3_s3: dcdc-reg8 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "vcc_3v3_s3"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vddq_ddr_s0: dcdc-reg9 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <600000>; + regulator-min-microvolt = <600000>; + regulator-name = "vddq_ddr_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8_s3: dcdc-reg10 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "vcc_1v8_s3"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc_1v8_s0: pldo-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "vcc_1v8_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca_1v8_s0: pldo-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "vcca_1v8_s0"; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdda_1v2_s0: pldo-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1200000>; + regulator-min-microvolt = <1200000>; + regulator-name = "vdda_1v2_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca_3v3_s0: pldo-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "vcca_3v3_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd_s0: pldo-reg5 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <1800000>; + regulator-name = "vccio_sd_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8_s3_pldo6: pldo-reg6 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "vcc_1v8_s3_pldo6"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd_0v75_s3: nldo-reg1 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <750000>; + regulator-min-microvolt = <750000>; + regulator-name = "vdd_0v75_s3"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <750000>; + }; + }; + + vdda_ddr_pll_s0: nldo-reg2 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <850000>; + regulator-min-microvolt = <850000>; + regulator-name = "vdda_ddr_pll_s0"; + regulator-state-mem { + regulator-off-in-suspend; + regulator-suspend-microvolt = <850000>; + }; + }; + + avdd_0v75_s0: nldo-reg3 { + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <750000>; + regulator-min-microvolt = <750000>; + regulator-name = "avdd_0v75_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v85_s0: nldo-reg4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <850000>; + regulator-name = "vdda_0v85_s0"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + /* Schematics show not in use */ + nldo-reg5 { + }; + }; + }; +}; + +&tsadc { + status = "okay"; +}; + +&uart2 { + pinctrl-0 = <&uart2m0_xfer>; + status = "okay"; +}; + +/* DMA seems to interfere with bluetooth device normal operation. */ +&uart9 { + pinctrl-0 = <&uart9m2_xfer>, <&uart9m2_ctsn>, <&uart9m2_rtsn>; + pinctrl-names = "default"; + /delete-property/ dma-names; + /delete-property/ dmas; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "realtek,rtl8821cs-bt", + "realtek,rtl8723bs-bt"; + device-wake-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; + enable-gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; + host-wake-gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&bt_reset>, <&bt_wake_dev>, <&bt_wake_host>; + pinctrl-names = "default"; + }; +};