The patch fixed all compilation errors for me, thank you. I did have to apply it manually, but that was rather simple.

I can confirm that SPDIF input doesn't work for the card, but I haven't applied the patch that you suggested to John Stile for that, yet. I'll do that a bit later today if you still recommend it

Is this patch still recommended?

diff -r 2d3893cf030c pci/hda/patch_via.c --- a/pci/hda/patch_via.c Tue Dec 18 15:42:53 2007 +0100 +++ b/pci/hda/patch_via.c Tue Dec 18 17:48:00 2007 +0100 @@ -568,25 +568,27 @@ static int via_init(struct hda_codec *co if (IS_VT1708_VENDORID(codec->vendor_id)) { snd_hda_codec_write(codec, VT1708_DIGIN_PIN, 0, AC_VERB_SET_PIN_WIDGET_CONTROL,

• 			    0x40);
  

• 			    PIN_OUT);
  snd_hda_codec_write(codec, VT1708_DIGIN_PIN, 0,
  		    AC_VERB_SET_EAPD_BTLENABLE, 0x02);
  

  } else if (IS_VT1709_10CH_VENDORID(codec->vendor_id) || IS_VT1709_6CH_VENDORID(codec->vendor_id)) { snd_hda_codec_write(codec, VT1709_DIGIN_PIN, 0, AC_VERB_SET_PIN_WIDGET_CONTROL,

• 			    0x40);
  

• 			    PIN_OUT);
  snd_hda_codec_write(codec, VT1709_DIGIN_PIN, 0,
  		    AC_VERB_SET_EAPD_BTLENABLE, 0x02);
  

  } else if (IS_VT1708B_8CH_VENDORID(codec->vendor_id) || IS_VT1708B_4CH_VENDORID(codec->vendor_id)) { snd_hda_codec_write(codec, VT1708B_DIGIN_PIN, 0, AC_VERB_SET_PIN_WIDGET_CONTROL,

• 			    0x40);
  

• 			    PIN_OUT);
  snd_hda_codec_write(codec, VT1708B_DIGIN_PIN, 0,
  		    AC_VERB_SET_EAPD_BTLENABLE, 0x02);
  

  }

• }

• } else /* enable SPDIF-input pin */

• snd_hda_codec_write(codec, spec->autocfg.dig_in_pin, 0,
  

• 		    AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN);
  
  

  return 0;

}

Thanks again!

-- Darryl

-------------- Original message ---------------------- From: Takashi Iwai tiwai@suse.de [...]

Thanks. Does the patch below fix the probelm? Run hgcompile after applying it.

Takashi

diff -r 414b1156a8b3 configure.in --- a/configure.in Tue Dec 18 16:09:20 2007 +0100 +++ b/configure.in Fri Dec 21 12:10:53 2007 +0100 @@ -1230,7 +1230,7 @@ esac

dnl set ia32 (X86) case "$processor" in

• i?86*|k?|crusoe|mcyrixiii|mwinchip|viac3_2|mcore2|geodegx*)

• i?86*|k?|crusoe|mcyrixiii|mwinchip|viac3_2|mcore2|geodegx*|x86_32) if $KCC -mpreferred-stack-boundary=2 -S -o /dev/null -xc /dev/null

...

/dev/null 2>&1; then

   c_opts="-mpreferred-stack-boundary=2 $c_opts"
   CONFIG_X86=y

---

Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel