[alsa-devel] [PATCH v5 0/9] Add Omapl138-Hawkboard support
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds EMAC, EDMA, ASoC, SOUND, MMC/SD and USB OHCI support for the Hawkboard-L138 system It is under the machine name "omapl138_hawkboard". This system is based on the da850 davinci CPU architecture.
Victor Rodriguez (9): davinci: EMAC support for Omapl138-Hawkboard davinci: EDMA support for Omapl138-Hawkboard davinci: ASoC support for Omapl138-Hawkboard davinci: McASP configuration for Omapl138-Hawkboard davinci: Audio support for Omapl138-Hawkboard davinci: MMC/SD and USB-OHCI configuration for Omapl138-Hawkboard davinci: MMC/SD support for Omapl138-Hawkboar davinci: USB clocks for Omapl138-Hawkboard davinci: USB1.1 support for Omapl138-Hawkboard
arch/arm/mach-davinci/board-omapl138-hawk.c | 317 +++++++++++++++++++++++++++ arch/arm/mach-davinci/da850.c | 22 ++- arch/arm/mach-davinci/include/mach/mux.h | 4 + sound/soc/davinci/Kconfig | 5 +- sound/soc/davinci/davinci-evm.c | 6 +- 5 files changed, 349 insertions(+), 5 deletions(-)
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds EMAC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- arch/arm/mach-davinci/board-omapl138-hawk.c | 47 +++++++++++++++++++++++++++ 1 files changed, 47 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c index c472dd8..8633245 100644 --- a/arch/arm/mach-davinci/board-omapl138-hawk.c +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -19,6 +19,51 @@
#include <mach/cp_intc.h> #include <mach/da8xx.h> +#include <mach/mux.h> + +#define HAWKBOARD_PHY_ID "0:07" + +static short omapl138_hawk_mii_pins[] __initdata = { + DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3, + DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER, + DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3, + DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + +static __init void omapl138_hawk_config_emac(void) +{ + void __iomem *cfgchip3 = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG); + int ret; + u32 val; + struct davinci_soc_info *soc_info = &davinci_soc_info; + + if (!machine_is_omapl138_hawkboard()) + return; + + val = __raw_readl(cfgchip3); + + val &= ~BIT(8); + ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins); + if (ret) { + pr_warning("%s: cpgmac/mii mux setup failed: %d\n", + __func__, ret); + return; + } + + /* configure the CFGCHIP3 register for MII */ + __raw_writel(val, cfgchip3); + pr_info("EMAC: MII PHY configured\n"); + + soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID; + + ret = da8xx_register_emac(); + if (ret) + pr_warning("%s: emac registration failed: %d\n", + __func__, ret); +} +
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = { .enabled_uarts = 0x7, @@ -30,6 +75,8 @@ static __init void omapl138_hawk_init(void)
davinci_serial_init(&omapl138_hawk_uart_config);
+ omapl138_hawk_config_emac(); + ret = da8xx_register_watchdog(); if (ret) pr_warning("omapl138_hawk_init: "
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds EDMA support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- arch/arm/mach-davinci/board-omapl138-hawk.c | 54 +++++++++++++++++++++++++++ 1 files changed, 54 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c index 8633245..ef3974e 100644 --- a/arch/arm/mach-davinci/board-omapl138-hawk.c +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -64,6 +64,55 @@ static __init void omapl138_hawk_config_emac(void) __func__, ret); }
+/* + * The following EDMA channels/slots are not being used by drivers (for + * example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM/Hawkboard, + * hence they are being reserved for codecs on the DSP side. + */ +static const s16 da850_dma0_rsv_chans[][2] = { + /* (offset, number) */ + { 8, 6}, + {24, 4}, + {30, 2}, + {-1, -1} +}; + +static const s16 da850_dma0_rsv_slots[][2] = { + /* (offset, number) */ + { 8, 6}, + {24, 4}, + {30, 50}, + {-1, -1} +}; + +static const s16 da850_dma1_rsv_chans[][2] = { + /* (offset, number) */ + { 0, 28}, + {30, 2}, + {-1, -1} +}; + +static const s16 da850_dma1_rsv_slots[][2] = { + /* (offset, number) */ + { 0, 28}, + {30, 90}, + {-1, -1} +}; + +static struct edma_rsv_info da850_edma_cc0_rsv = { + .rsv_chans = da850_dma0_rsv_chans, + .rsv_slots = da850_dma0_rsv_slots, +}; + +static struct edma_rsv_info da850_edma_cc1_rsv = { + .rsv_chans = da850_dma1_rsv_chans, + .rsv_slots = da850_dma1_rsv_slots, +}; + +static struct edma_rsv_info *da850_edma_rsv[2] = { + &da850_edma_cc0_rsv, + &da850_edma_cc1_rsv, +};
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = { .enabled_uarts = 0x7, @@ -77,6 +126,11 @@ static __init void omapl138_hawk_init(void)
omapl138_hawk_config_emac();
+ ret = da850_register_edma(da850_edma_rsv); + if (ret) + pr_warning("%s: EDMA registration failed: %d\n", + __func__, ret); + ret = da8xx_register_watchdog(); if (ret) pr_warning("omapl138_hawk_init: "
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds ASoC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- sound/soc/davinci/Kconfig | 5 +++-- sound/soc/davinci/davinci-evm.c | 6 ++++-- 2 files changed, 7 insertions(+), 4 deletions(-)
diff --git a/sound/soc/davinci/Kconfig b/sound/soc/davinci/Kconfig index 6bbf001..72c6752 100644 --- a/sound/soc/davinci/Kconfig +++ b/sound/soc/davinci/Kconfig @@ -76,8 +76,9 @@ config SND_DA830_SOC_EVM DA830/OMAP-L137 EVM
config SND_DA850_SOC_EVM - tristate "SoC Audio support for DA850/OMAP-L138 EVM" - depends on SND_DAVINCI_SOC && MACH_DAVINCI_DA850_EVM + tristate "SoC Audio support for DA850/OMAP-L138 EVM/Hawkboard" + depends on SND_DAVINCI_SOC && (MACH_DAVINCI_DA850_EVM || \ + MACH_OMAPL138_HAWKBOARD) select SND_DAVINCI_SOC_MCASP select SND_SOC_TLV320AIC3X help diff --git a/sound/soc/davinci/davinci-evm.c b/sound/soc/davinci/davinci-evm.c index 97f74d6..73093eb 100644 --- a/sound/soc/davinci/davinci-evm.c +++ b/sound/soc/davinci/davinci-evm.c @@ -59,7 +59,8 @@ static int evm_hw_params(struct snd_pcm_substream *substream, sysclk = 12288000;
else if (machine_is_davinci_da830_evm() || - machine_is_davinci_da850_evm()) + machine_is_davinci_da850_evm() || + machine_is_omapl138_hawkboard()) sysclk = 24576000;
else @@ -311,7 +312,8 @@ static int __init evm_init(void) } else if (machine_is_davinci_da830_evm()) { evm_snd_dev_data = &da830_evm_snd_devdata; index = 1; - } else if (machine_is_davinci_da850_evm()) { + } else if (machine_is_davinci_da850_evm() || + machine_is_omapl138_hawkboard()) { evm_snd_dev_data = &da850_evm_snd_devdata; index = 0; } else
On Tue, Oct 19, 2010 at 01:06:21PM -0500, vm.rod25@gmail.com wrote:
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds ASoC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com
Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com
Please do remember to CC maintainers on patches so they see them.
On Thu, Oct 21, 2010 at 5:28 PM, Mark Brown broonie@opensource.wolfsonmicro.com wrote:
On Tue, Oct 19, 2010 at 01:06:21PM -0500, vm.rod25@gmail.com wrote:
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds ASoC support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com
Acked-by: Mark Brown broonie@opensource.wolfsonmicro.com
Please do remember to CC maintainers on patches so they see them.
Hi Mark I am going to resend this series of patches because of one small coding stile problem, is this ok for you if I resend this patches with CC to you and alsa mailing list ?
Thanks
Victor Rodriguez
On Thu, Oct 28, 2010 at 02:01:27PM -0500, Victor Rodriguez wrote:
On Thu, Oct 21, 2010 at 5:28 PM, Mark Brown
Please do remember to CC maintainers on patches so they see them.
Hi Mark I am going to resend this series of patches because of one small coding stile problem, is this ok for you if I resend this patches with CC to you and alsa mailing list ?
Yes, please CC myself and Liam on all ASoC patches.
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- arch/arm/mach-davinci/da850.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 63916b9..f033a0a 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = { const short da850_mcasp_pins[] __initdata = { DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, - DA850_AXR_11, DA850_AXR_12, + DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14, -1 };
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds sound support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- Notes:
This patch works with da8xx_omapl_defconfig
In order to test ALSA utils select in menuconfig like insmodule:
Sound card support ---> Advanced Linux Sound Architecture ---> ALSA for SoC audio support ---> SoC Audio for the TI DAVINCI chip SoC Audio support for DA850/OMAP-L138 EVM/Hawkboard
arch/arm/mach-davinci/board-omapl138-hawk.c | 46 +++++++++++++++++++++++++++ 1 files changed, 46 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c index ef3974e..97836e9 100644 --- a/arch/arm/mach-davinci/board-omapl138-hawk.c +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -13,6 +13,7 @@ #include <linux/init.h> #include <linux/console.h> #include <linux/gpio.h> +#include <linux/i2c.h>
#include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -114,6 +115,38 @@ static struct edma_rsv_info *da850_edma_rsv[2] = { &da850_edma_cc1_rsv, };
+static struct i2c_board_info __initdata omapl138_hawk_i2c_devices[] = { + { + I2C_BOARD_INFO("tlv320aic3x", 0x18), + }, +}; + +static struct davinci_i2c_platform_data omapl138_hawk_i2c_0_pdata = { + .bus_freq = 100, /* kHz */ + .bus_delay = 0, /* usec */ +}; + +/* davinci Hawkboard audio machine driver */ +static u8 da850_iis_serializer_direction[] = { + INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, + INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, + INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, + INACTIVE_MODE, TX_MODE, RX_MODE, INACTIVE_MODE, +}; + +static struct snd_platform_data omapl138_hawk_snd_data = { + .tx_dma_offset = 0x2000, + .rx_dma_offset = 0x2000, + .op_mode = DAVINCI_MCASP_IIS_MODE, + .num_serializer = ARRAY_SIZE(da850_iis_serializer_direction), + .tdm_slots = 2, + .serial_dir = da850_iis_serializer_direction, + .asp_chan_q = EVENTQ_1, + .version = MCASP_VERSION_2, + .txnumevt = 1, + .rxnumevt = 1, +}; + static struct davinci_uart_config omapl138_hawk_uart_config __initdata = { .enabled_uarts = 0x7, }; @@ -131,6 +164,19 @@ static __init void omapl138_hawk_init(void) pr_warning("%s: EDMA registration failed: %d\n", __func__, ret);
+ i2c_register_board_info(1, omapl138_hawk_i2c_devices, + ARRAY_SIZE(omapl138_hawk_i2c_devices)); + + ret = da8xx_register_i2c(0, &omapl138_hawk_i2c_0_pdata); + if (ret) + pr_warning("%s: i2c0 registration failed: %d\n", + __func__, ret); + + ret = davinci_cfg_reg_list(da850_mcasp_pins); + if (ret) + pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret); + da8xx_register_mcasp(0, &omapl138_hawk_snd_data); + ret = da8xx_register_watchdog(); if (ret) pr_warning("omapl138_hawk_init: "
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch defines Pin Mux configuration to enable MMC/SD and USB-OHCI on the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- arch/arm/mach-davinci/da850.c | 4 ++++ arch/arm/mach-davinci/include/mach/mux.h | 4 ++++ 2 files changed, 8 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index f033a0a..4458bff 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -543,11 +543,15 @@ static const struct mux_config da850_pins[] = { MUX_CFG(DA850, EMA_WAIT_1, 6, 24, 15, 1, false) MUX_CFG(DA850, NEMA_CS_2, 7, 0, 15, 1, false) /* GPIO function */ + MUX_CFG(DA850, GPIO2_4, 6, 12, 15, 8, false) MUX_CFG(DA850, GPIO2_6, 6, 4, 15, 8, false) MUX_CFG(DA850, GPIO2_8, 5, 28, 15, 8, false) MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false) + MUX_CFG(DA850, GPIO3_12, 7, 12, 15, 8, false) + MUX_CFG(DA850, GPIO3_13, 7, 8, 15, 8, false) MUX_CFG(DA850, GPIO4_0, 10, 28, 15, 8, false) MUX_CFG(DA850, GPIO4_1, 10, 24, 15, 8, false) + MUX_CFG(DA850, GPIO6_13, 13, 8, 15, 8, false) MUX_CFG(DA850, RTC_ALARM, 0, 28, 15, 2, false) #endif }; diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h index de11aac..5d4e0fe 100644 --- a/arch/arm/mach-davinci/include/mach/mux.h +++ b/arch/arm/mach-davinci/include/mach/mux.h @@ -908,11 +908,15 @@ enum davinci_da850_index { DA850_NEMA_CS_2,
/* GPIO function */ + DA850_GPIO2_4, DA850_GPIO2_6, DA850_GPIO2_8, DA850_GPIO2_15, + DA850_GPIO3_12, + DA850_GPIO3_13, DA850_GPIO4_0, DA850_GPIO4_1, + DA850_GPIO6_13, DA850_RTC_ALARM, };
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds MMC/SD support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- Notes:
This patch works with da8xx_omapl_defconfig In order to test it select in menuconfig like insmodule
MMC/SD/SDIO card support ---> MMC block device driver Use bounce buffer for simple hosts TI DAVINCI Multimedia Card Interface support
arch/arm/mach-davinci/board-omapl138-hawk.c | 63 +++++++++++++++++++++++++++ 1 files changed, 63 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c index 97836e9..c83050b 100644 --- a/arch/arm/mach-davinci/board-omapl138-hawk.c +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -23,6 +23,8 @@ #include <mach/mux.h>
#define HAWKBOARD_PHY_ID "0:07" +#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12) +#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13)
static short omapl138_hawk_mii_pins[] __initdata = { DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3, @@ -147,6 +149,65 @@ static struct snd_platform_data omapl138_hawk_snd_data = { .rxnumevt = 1, };
+static const short hawk_mmcsd0_pins[] = { + DA850_MMCSD0_DAT_0, DA850_MMCSD0_DAT_1, DA850_MMCSD0_DAT_2, + DA850_MMCSD0_DAT_3, DA850_MMCSD0_CLK, DA850_MMCSD0_CMD, + DA850_GPIO3_12, DA850_GPIO3_13, + -1 +}; + +static int da850_hawk_mmc_get_ro(int index) +{ + return gpio_get_value(DA850_HAWK_MMCSD_WP_PIN); +} + +static int da850_hawk_mmc_get_cd(int index) +{ + return !gpio_get_value(DA850_HAWK_MMCSD_CD_PIN); +} + +static struct davinci_mmc_config da850_mmc_config = { + .get_ro = da850_hawk_mmc_get_ro, + .get_cd = da850_hawk_mmc_get_cd, + .wires = 4, + .max_freq = 50000000, + .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED, + .version = MMC_CTLR_VERSION_2, +}; + +static __init void omapl138_hawk_mmc_init(void) +{ + int ret; + + ret = davinci_cfg_reg_list(hawk_mmcsd0_pins); + if (ret) { + pr_warning("%s: MMC/SD0 mux setup failed: %d\n", + __func__, ret); + return; + } + + ret = gpio_request_one(DA850_HAWK_MMCSD_CD_PIN, + GPIOF_DIR_IN, "MMC CD"); + if (ret < 0) { + pr_warning("%s: can not open GPIO %d\n", + __func__, DA850_HAWK_MMCSD_CD_PIN); + return; + } + + ret = gpio_request_one(DA850_HAWK_MMCSD_WP_PIN, + GPIOF_DIR_IN, "MMC WP"); + if (ret < 0) { + pr_warning("%s: can not open GPIO %d\n", + __func__, DA850_HAWK_MMCSD_WP_PIN); + return; + } + + ret = da8xx_register_mmcsd0(&da850_mmc_config); + if (ret) + pr_warning("%s: MMC/SD0 registration failed: %d\n", + __func__, ret); +} + static struct davinci_uart_config omapl138_hawk_uart_config __initdata = { .enabled_uarts = 0x7, }; @@ -177,6 +238,8 @@ static __init void omapl138_hawk_init(void) pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret); da8xx_register_mcasp(0, &omapl138_hawk_snd_data);
+ omapl138_hawk_mmc_init(); + ret = da8xx_register_watchdog(); if (ret) pr_warning("omapl138_hawk_init: "
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds USB1.1 and USB2.0 clocks for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- arch/arm/mach-davinci/da850.c | 16 ++++++++++++++++ 1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 4458bff..b3b1adb 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -345,6 +345,20 @@ static struct clk aemif_clk = { .flags = ALWAYS_ENABLED, };
+static struct clk usb11_clk = { + .name = "usb11", + .parent = &pll0_sysclk4, + .lpsc = DA8XX_LPSC1_USB11, + .gpsc = 1, +}; + +static struct clk usb20_clk = { + .name = "usb20", + .parent = &pll0_sysclk2, + .lpsc = DA8XX_LPSC1_USB20, + .gpsc = 1, +}; + static struct clk_lookup da850_clks[] = { CLK(NULL, "ref", &ref_clk), CLK(NULL, "pll0", &pll0_clk), @@ -387,6 +401,8 @@ static struct clk_lookup da850_clks[] = { CLK("davinci_mmc.0", NULL, &mmcsd0_clk), CLK("davinci_mmc.1", NULL, &mmcsd1_clk), CLK(NULL, "aemif", &aemif_clk), + CLK(NULL, "usb11", &usb11_clk), + CLK(NULL, "usb20", &usb20_clk), CLK(NULL, NULL, NULL), };
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds USB1.1 support for the Hawkboard-L138 system
Signed-off-by: Victor Rodriguez victor.rodriguez@sasken.com --- Notes:
This patch works with da8xx_omapl_defconfig In order to test it select in menuconfig like insmodule
Device Drivers ---> SCSI device support ---> SCSI device support legacy /proc/scsi/ support SCSI disk support SCSI low-level drivers
USB support ---> Support for Host-side US OHCI HCD support (NEW) USB Mass Storage support (NEW) USB Gadget Support ---> USB Gadget Drivers (Ethernet Gadget\ (with CDC Ethernet support)) ---> NOP USB Transceiver Driver
And you will be able to mount and USB pen drive
In order to connect a keyboard or a mouse on a USB-hub select in menuconfig like insmodule
HID Devices ---> Generic HID support USB Human Interface Device (full HID) support
arch/arm/mach-davinci/board-omapl138-hawk.c | 107 +++++++++++++++++++++++++++ 1 files changed, 107 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c index c83050b..1531717 100644 --- a/arch/arm/mach-davinci/board-omapl138-hawk.c +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -26,6 +26,9 @@ #define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12) #define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13)
+#define DA850_USB1_VBUS_PIN GPIO_TO_PIN(2, 4) +#define DA850_USB1_OC_PIN GPIO_TO_PIN(6, 13) + static short omapl138_hawk_mii_pins[] __initdata = { DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3, DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER, @@ -208,6 +211,108 @@ static __init void omapl138_hawk_mmc_init(void) __func__, ret); }
+static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id); +static da8xx_ocic_handler_t hawk_usb_ocic_handler; + +static const short da850_hawk_usb11_pins[] = { + DA850_GPIO2_4, DA850_GPIO6_13, + -1 +}; + +static int hawk_usb_set_power(unsigned port, int on) +{ + gpio_set_value(DA850_USB1_VBUS_PIN, on); + return 0; +} + +static int hawk_usb_get_power(unsigned port) +{ + return gpio_get_value(DA850_USB1_VBUS_PIN); +} + +static int hawk_usb_get_oci(unsigned port) +{ + return !gpio_get_value(DA850_USB1_OC_PIN); +} + +static int hawk_usb_ocic_notify(da8xx_ocic_handler_t handler) +{ + int irq = gpio_to_irq(DA850_USB1_OC_PIN); + int error = 0; + + if (handler != NULL) { + hawk_usb_ocic_handler = handler; + + error = request_irq(irq, omapl138_hawk_usb_ocic_irq, + IRQF_DISABLED | IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING, + "OHCI over-current indicator", NULL); + if (error) + pr_err(KERN_ERR "%s: could not request IRQ to watch " + "over-current indicator changes\n", __func__); + } else + free_irq(irq, NULL); + + return error; +} + +static struct da8xx_ohci_root_hub omapl138_hawk_usb11_pdata = { + .set_power = hawk_usb_set_power, + .get_power = hawk_usb_get_power, + .get_oci = hawk_usb_get_oci, + .ocic_notify = hawk_usb_ocic_notify, + /* TPS2087 switch @ 5V */ + .potpgt = (3 + 1) / 2, /* 3 ms max */ +}; + +static irqreturn_t omapl138_hawk_usb_ocic_irq(int irq, void *dev_id) +{ + hawk_usb_ocic_handler(&omapl138_hawk_usb11_pdata, 1); + return IRQ_HANDLED; +} + +static __init void omapl138_hawk_usb_init(void) +{ + int ret; + u32 cfgchip2; + + ret = davinci_cfg_reg_list(da850_hawk_usb11_pins); + if (ret) { + pr_warning("%s: USB 1.1 PinMux setup failed: %d\n", + __func__, ret); + return; + } + + /* + * Setup the Ref. clock frequency for the HAWK at 24 MHz. + */ + cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG)); + cfgchip2 &= ~CFGCHIP2_REFFREQ; + cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ; + __raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG)); + + ret = gpio_request_one(DA850_USB1_VBUS_PIN, + GPIOF_DIR_OUT, "USB1 VBUS"); + if (ret < 0) { + pr_err(KERN_ERR "%s: failed to request GPIO for USB 1.1 port " + "power control: %d\n", __func__, ret); + return; + } + + ret = gpio_request_one(DA850_USB1_OC_PIN, + GPIOF_DIR_IN, "USB1 OC"); + if (ret < 0) { + pr_err(KERN_ERR "%s: failed to request GPIO for USB 1.1 port " + "over-current indicator: %d\n", __func__, ret); + return; + } + + ret = da8xx_register_usb11(&omapl138_hawk_usb11_pdata); + if (ret) + pr_warning("%s: USB 1.1 registration failed: %d\n", + __func__, ret); +} + static struct davinci_uart_config omapl138_hawk_uart_config __initdata = { .enabled_uarts = 0x7, }; @@ -240,6 +345,8 @@ static __init void omapl138_hawk_init(void)
omapl138_hawk_mmc_init();
+ omapl138_hawk_usb_init(); + ret = da8xx_register_watchdog(); if (ret) pr_warning("omapl138_hawk_init: "
On Tue, 2010-10-19 at 13:06 -0500, vm.rod25@gmail.com wrote:
From: Victor Rodriguez victor.rodriguez@sasken.com
This patch adds EMAC, EDMA, ASoC, SOUND, MMC/SD and USB OHCI support for the Hawkboard-L138 system It is under the machine name "omapl138_hawkboard". This system is based on the da850 davinci CPU architecture.
Victor Rodriguez (9): davinci: EMAC support for Omapl138-Hawkboard davinci: EDMA support for Omapl138-Hawkboard davinci: ASoC support for Omapl138-Hawkboard davinci: McASP configuration for Omapl138-Hawkboard davinci: Audio support for Omapl138-Hawkboard davinci: MMC/SD and USB-OHCI configuration for Omapl138-Hawkboard davinci: MMC/SD support for Omapl138-Hawkboar davinci: USB clocks for Omapl138-Hawkboard davinci: USB1.1 support for Omapl138-Hawkboard
arch/arm/mach-davinci/board-omapl138-hawk.c | 317 +++++++++++++++++++++++++++ arch/arm/mach-davinci/da850.c | 22 ++- arch/arm/mach-davinci/include/mach/mux.h | 4 + sound/soc/davinci/Kconfig | 5 +- sound/soc/davinci/davinci-evm.c | 6 +- 5 files changed, 349 insertions(+), 5 deletions(-)
ASoC parts :-
Acked-by: Liam Girdwood lrg@slimlogic.co.uk
participants (4)
-
Liam Girdwood -
Mark Brown -
Victor Rodriguez -
vm.rod25＠gmail.com