[alsa-devel] Fwd: No sound with ATI SB450
Tobin, I downloaded and installed alsa-driver, alsa-lib and alsa-utils, but still no sound coming out of those speakers... I ran alsa-info.sh and the results are at http://pastebin.ca/451128 I am clueless as to what to do next, but I m ready to try anything. Any help would be greatly appreciated. Ben
On 4/21/07, Tobin Davis < tdavis@dsl-only.net> wrote:
Try downloading a current daily snapshot from ftp://ftp.suse.com/pub/projects/alsa/snapshot/ .
There was an issue with the ATI HD Audio detection that was fixed after 14rc3 was released.
Tobin
On Sat, 2007-04-21 at 16:00 +1000, Ben DiDonc wrote:
The output of alsa-info.sh is available at http://pastebin.ca/451007
On 4/21/07, *Tobin Davis* < tdavis@dsl-only.net> wrote:
Could you download an run http://bulletproof.servebeer.com/alsa/scripts/alsa-info.sh , then post the resulting link? This will help determine what setup you have.
Tobin Davis
On Sat, 2007-04-21 at 14:56 +1000, Ben DiDonc wrote:
Hi I have a toshiba A100 (see attached file lspci-nnv) with a ATI SB450. Sound worked fine with kernel 2.6.17 and alsa 1.0.12rc1 (ubuntu edgy). I just did a fresh install of ubuntu feisty (kernel 2.6.20, alsa 1.0.14rc1) and the only mixer settings available are those of the modem, named off-hook and caller-id (see output of amixer, aplay -l , and the rest in attached file output_feisty) I decided to upgrade alsa-driver and alsa-lib to 1.0.14rc2. after downloading the package, I unloaded all sound related modules (everything with "snd_" in it) in the right order and did: ./configure --with-oss=yes --with-cards=hda-intel;make; sudo make install; sudo modprobe snd_hda_intel A minor improvement: the mixer now shows controls for both the modem and the sound card (see output_after_upgrade_to_rc2), but unfortunately, there is still no sound coming out of those speakers (even though alsamixer shows control for PCM and the rest...). Finally, I downloaded alsa-driver-1.0.14rc3 and gave it a shot. This time again, only modem related settings appeared in alsamixer, and no sound card stuff (see aplay and amixer in output_after_upgrade_to_rc3), and no sound either. Does anyone know how to get some sound out of these speakers (given that it used to work with alsa1.0.12rc1...) ? Thanks for your help Ben
_______________________________________________Alsa-devel mailing listAlsa-devel@alsa-project.orghttp://mailman.alsa-project.org/mailman/listinfo/alsa-devel
-- Tobin Davis tdavis@dsl-only.net
-- Tobin Davis tdavis@dsl-only.net
Which snapshot did you download? It looks as if the driver isn't detecting your codec at all. Is it possible that your audio is disabled in bios? Also, Toshiba's are notorious for their acpi issues. Try rebooting with "acpi=off" on the kernel boot parameters list.
To help us debug this further if the above steps don't work, try recompiling the drivers with "./configure --with-debug=detect --with-cards=hda-intel". Then rebuild and reinstall the drivers, and look at the dmesg log with "dmesg | fgrep ALSA".
Your system "should" show up as a Toshiba with RealTek ALC861 audio codec. The alsa-info.sh listing doesn't show that codec, but does list the subdevice ID.
Tobin
On Sat, 2007-04-21 at 20:27 +1000, Ben DiDonc wrote:
Tobin, I downloaded and installed alsa-driver, alsa-lib and alsa-utils, but still no sound coming out of those speakers... I ran alsa-info.sh and the results are at http://pastebin.ca/451128 I am clueless as to what to do next, but I m ready to try anything. Any help would be greatly appreciated. Ben
On 4/21/07, Tobin Davis < tdavis@dsl-only.net> wrote:
Try downloading a current daily snapshot from ftp://ftp.suse.com/pub/projects/alsa/snapshot/ .
There was an issue with the ATI HD Audio detection that was fixed after 14rc3 was released.
Tobin
On Sat, 2007-04-21 at 16:00 +1000, Ben DiDonc wrote:
The output of alsa-info.sh is available at http://pastebin.ca/451007
On 4/21/07, *Tobin Davis* < tdavis@dsl-only.net> wrote:
Could you download an run http://bulletproof.servebeer.com/alsa/scripts/alsa-info.sh , then post the resulting link? This will help determine what setup you have.
Tobin Davis
On Sat, 2007-04-21 at 14:56 +1000, Ben DiDonc wrote:
Hi I have a toshiba A100 (see attached file lspci-nnv) with a ATI SB450. Sound worked fine with kernel 2.6.17 and alsa 1.0.12rc1 (ubuntu edgy). I just did a fresh install of ubuntu feisty (kernel 2.6.20, alsa 1.0.14rc1) and the only mixer settings available are those of the modem, named off-hook and caller-id (see output of amixer, aplay -l , and the rest in attached file output_feisty) I decided to upgrade alsa-driver and alsa-lib to 1.0.14rc2. after downloading the package, I unloaded all sound related modules (everything with "snd_" in it) in the right order and did: ./configure --with-oss=yes --with-cards=hda-intel;make; sudo make install; sudo modprobe snd_hda_intel A minor improvement: the mixer now shows controls for both the modem and the sound card (see output_after_upgrade_to_rc2), but unfortunately, there is still no sound coming out of those speakers (even though alsamixer shows control for PCM and the rest...). Finally, I downloaded alsa-driver-1.0.14rc3 and gave it a shot. This time again, only modem related settings appeared in alsamixer, and no sound card stuff (see aplay and amixer in output_after_upgrade_to_rc3), and no sound either. Does anyone know how to get some sound out of these speakers (given that it used to work with alsa1.0.12rc1...) ? Thanks for your help Ben
_______________________________________________Alsa-devel mailing listAlsa-devel@alsa-project.orghttp://mailman.alsa-project.org/mailman/listinfo/alsa-devel
-- Tobin Davis tdavis@dsl-only.net
-- Tobin Davis tdavis@dsl-only.net
Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Tobin,
Which snapshot did you download?
I used alsa-driver-hd20070421
It looks as if the driver isn't detecting your codec at all. Is it
possible that your audio is disabled in bios?
I agree with you. This laptop has a strange BIOS, you can disable a couple of things (network card,...) but not the sound card.
Also, Toshiba's are notorious for their acpi issues. Try rebooting with
"acpi=off" on the kernel boot parameters list.
No improvement here, no difference with what I had before... still no sound ...
To help us debug this further if the above steps don't work, try recompiling
the drivers with "./configure --with-debug=detect --with-cards=hda-intel". Then rebuild and reinstall the drivers, and look at the dmesg log with "dmesg | fgrep ALSA".
Ok, I rebuild the drivers with the configure options you gave me, and reloaded them. I grepped my syslog and got a single line out of it: Apr 22 19:07:50 tosh-it kernel: [89422.940000] ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-hg20070421/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696: codec_mask = 0x9
but still no proper senses shown in alsamixer and no sound. See output of alsa-info.sh at http://pastebin.ca/452475
Your system "should" show up as a Toshiba with RealTek ALC861 audio codec.
The alsa-info.sh listing doesn't show that codec, but does list the subdevice ID.
Tobin
I did a bit of research on the devel mailing list and found http://article.gmane.org/gmane.linux.alsa.devel/45881 I tried applying the patch (to hda_intel.c) and realised most of it already was in the snapshot EXCEPT line 995, which i replaced with the one from the patch. It now is for (c = 0; c < azx_max_codecs[chip->driver_type]; c++) {
I rebuilt the whole lot, reloaded snd_hda_intel and got these two lines this time:
Apr 22 19:39:01 tosh-it kernel: [91293.576000] ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-hg20070421/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696: codec_mask = 0x9 Apr 22 19:39:01 tosh-it kernel: [91293.916000] ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-hg20070421/pci/hda/hda_codec.c:1819: hda_codec: model 'toshiba' is selected for config 1179:ff10 (Toshiba)
This time the right codec is loaded (or so it seems), alsamixer only shows a PCM control (for playback), but there is still no sound. alsa-info.sh output at http://pastebin.ca/452493
I m a bit confused with these results... Ben
On Sat, 2007-04-21 at 20:27 +1000, Ben DiDonc wrote:
Tobin,I downloaded and installed alsa-driver, alsa-lib and alsa-utils, but stillno sound coming out of those speakers...I ran alsa-info.sh and the results are at http://pastebin.ca/451128I am clueless as to what to do next, but I m ready to try anything. Any help would be greatly appreciated.Ben On 4/21/07, Tobin Davis < tdavis@dsl-only.net> wrote:>> Try downloading a current daily snapshot from ftp://ftp.suse.com/pub/projects/alsa/snapshot/> .>> There was an issue with the ATI HD Audio detection that was fixed after> 14rc3 was released.>> Tobin>> On Sat, 2007-04-21 at 16:00 +1000, Ben DiDonc wrote:>> The output of alsa-info.sh is available at http://pastebin.ca/451007%3E%3E%3E On 4/21/07, *Tobin Davis* < tdavis@dsl-only.net> wrote:>> Could you download an run http://bulletproof.servebeer.com/alsa/scripts/alsa-info.sh%3E , then post the resulting link? This will help determine what setup you> have.>> Tobin Davis>>>> On Sat, 2007-04-21 at 14:56 +1000, Ben DiDonc wrote:>> Hi I have a toshiba A100 (see attached file lspci-nnv) with a ATI SB450.> Sound worked fine with kernel 2.6.17 and alsa 1.0.12rc1 (ubuntu edgy). I> just did a fresh install of ubuntu feisty (kernel 2.6.20, alsa 1.0.14rc1)> and the only mixer settings available are those of the modem, named off-hook> and caller-id (see output of amixer, aplay -l , and the rest in attached> file output_feisty) I decided to upgrade alsa-driver and alsa-lib to> 1.0.14rc2. after downloading the package, I unloaded all sound related> modules (everything with "snd_" in it) in the right order and did:> ./configure --with-oss=yes --with-cards=hda-intel;make; sudo make install;> sudo modprobe snd_hda_intel A minor improvement: the mixer now shows> controls for both the modem and the sound card (see> output_after_upgrade_to_rc2), but unfortunately, there is still no sound> coming out of those speakers (even though alsamixer shows control for PCM> and the rest...). Finally, I downloaded alsa-driver-1.0.14rc3 and gave it> a shot. This time again, only modem related settings appeared in alsamixer,> and no sound card stuff (see aplay and amixer in> output_after_upgrade_to_rc3), and no sound either. Does anyone know how to> get some sound out of these speakers (given that it used to work with> alsa1.0.12rc1...) ? Thanks for your help Ben>
_______________________________________________Alsa-devel mailing listAlsa-devel@alsa-project.orghttp://mailman.alsa-project.org/mailman/listinfo/alsa-devel%3E%3E --> Tobin Davis tdavis@dsl-only.net>>> --> Tobin Davis tdavis@dsl-only.net>_______________________________________________Alsa-devel mailing listAlsa-devel@alsa-project.orghttp://mailman.alsa-project.org/mailman/listinfo/alsa-devel
-- Tobin Davis tdavis@dsl-only.net
I reviewed the changelogs after the patch you found was added, and found this entry (patch is attached so you can review it):
Probing the codec slots on ATI controller causes problems on some devices like Acer laptops. On these devices, reading from codec slot 3 results in the communication failure with the codec chip. Meanwhile, some laptops (e.g. Gateway) have the codec connection only on slot 3, and probing this slot is mandatory for them.
The patch improves the probing robustness. The additional slots are now checked only when no codecs are found in the primary three slots.
The problem is that there are so many issues with ATI based chipsets, that we almost need to fix this on a case by case basis. Your particular system has the modem wired to show up before the audio chip on the HDA bus. I'm also willing to bet that the acpi issues are affecting your system as well.
I'm also looking through my email archives to see what other users had reported to me since I added your system to the driver back in October. Maybe they can shed some light on these issues.
For a simple test, could you try alsa-driver-1.0.14rc2? It has your system, but none of the ATI issues (from what I can tell). In the mean time, I'll see if I can come up with a clean solution to this.
Tobin
On Sun, 2007-04-22 at 19:45 +1000, Ben DiDonc wrote:
Tobin,
Which snapshot did you download?
I used alsa-driver-hd20070421
It looks as if the driver isn't detecting your codec at all. Is it
possible that your audio is disabled in bios?
I agree with you. This laptop has a strange BIOS, you can disable a couple of things (network card,...) but not the sound card.
Also, Toshiba's are notorious for their acpi issues. Try rebooting
with "acpi=off" on the kernel boot parameters list.
No improvement here, no difference with what I had before... still no sound ...
To help us debug this further if the above steps don't work, try recompiling the drivers with "./configure --with-debug=detect --with-cards=hda-intel". Then rebuild and reinstall the drivers, and look at the dmesg log with "dmesg | fgrep ALSA".Ok, I rebuild the drivers with the configure options you gave me, and reloaded them. I grepped my syslog and got a single line out of it: Apr 22 19:07:50 tosh-it kernel: [89422.940000] ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-hg20070421/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696: codec_mask = 0x9
but still no proper senses shown in alsamixer and no sound. See output of alsa-info.sh at http://pastebin.ca/452475
Your system "should" show up as a Toshiba with RealTek ALC861 audio codec. The alsa-info.sh listing doesn't show that codec, but does list the subdevice ID. TobinI did a bit of research on the devel mailing list and found http://article.gmane.org/gmane.linux.alsa.devel/45881 I tried applying the patch (to hda_intel.c) and realised most of it already was in the snapshot EXCEPT line 995, which i replaced with the one from the patch. It now is for (c = 0; c < azx_max_codecs[chip->driver_type]; c++) {
I rebuilt the whole lot, reloaded snd_hda_intel and got these two lines this time:
Apr 22 19:39:01 tosh-it kernel: [91293.576000] ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-hg20070421/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696: codec_mask = 0x9 Apr 22 19:39:01 tosh-it kernel: [91293.916000] ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-hg20070421/pci/hda/hda_codec.c:1819: hda_codec: model 'toshiba' is selected for config 1179:ff10 (Toshiba)
This time the right codec is loaded (or so it seems), alsamixer only shows a PCM control (for playback), but there is still no sound. alsa-info.sh output at http://pastebin.ca/452493
I m a bit confused with these results... Ben
On Sat, 2007-04-21 at 20:27 +1000, Ben DiDonc wrote: > Tobin, I downloaded and installed alsa-driver, alsa-lib and > alsa-utils, but still no sound coming out of those > speakers... I ran alsa-info.sh and the results are at > http://pastebin.ca/451128 I am clueless as to what to do > next, but I m ready to try anything. Any help would be > greatly appreciated. Ben On 4/21/07, Tobin Davis < > tdavis@dsl-only.net> wrote: > > Try downloading a current > daily snapshot from > ftp://ftp.suse.com/pub/projects/alsa/snapshot/ > . > > There > was an issue with the ATI HD Audio detection that was fixed > after > 14rc3 was released. > > Tobin > > On Sat, 2007-04-21 > at 16:00 +1000, Ben DiDonc wrote: > > The output of > alsa-info.sh is available at http://pastebin.ca/451007 > > > > On 4/21/07, *Tobin Davis* < tdavis@dsl-only.net> wrote: > > > Could you download an run > http://bulletproof.servebeer.com/alsa/scripts/alsa-info.sh > > , then post the resulting link? This will help determine > what setup you > have. > > Tobin Davis > > > > On Sat, > 2007-04-21 at 14:56 +1000, Ben DiDonc wrote: > > Hi I have > a toshiba A100 (see attached file lspci-nnv) with a ATI > SB450. > Sound worked fine with kernel 2.6.17 and alsa > 1.0.12rc1 (ubuntu edgy). I > just did a fresh install of > ubuntu feisty (kernel 2.6.20, alsa 1.0.14rc1) > and the only > mixer settings available are those of the modem, named > off-hook > and caller-id (see output of amixer, aplay -l , > and the rest in attached > file output_feisty) I decided to > upgrade alsa-driver and alsa-lib to > 1.0.14rc2. after > downloading the package, I unloaded all sound related > > modules (everything with "snd_" in it) in the right order > and did: > ./configure --with-oss=yes > --with-cards=hda-intel;make; sudo make install; > sudo > modprobe snd_hda_intel A minor improvement: the mixer now > shows > controls for both the modem and the sound card (see > > output_after_upgrade_to_rc2), but unfortunately, there is > still no sound > coming out of those speakers (even though > alsamixer shows control for PCM > and the rest...). Finally, > I downloaded alsa-driver-1.0.14rc3 and gave it > a shot. > This time again, only modem related settings appeared in > alsamixer, > and no sound card stuff (see aplay and amixer > in > output_after_upgrade_to_rc3), and no sound either. Does > anyone know how to > get some sound out of these speakers > (given that it used to work with > alsa1.0.12rc1...) ? > Thanks for your help Ben > > > > _______________________________________________Alsa-devel mailing > listAlsa-devel@alsa-project.orghttp://mailman.alsa-project.org/mailman/listinfo/alsa-devel > > > > > -- > > Tobin Davis <tdavis@dsl-only.net> > > > > > > -- > > Tobin Davis <tdavis@dsl-only.net> > > > _______________________________________________ > Alsa-devel mailing list > Alsa-devel@alsa-project.org > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > -- Tobin Davis <tdavis@dsl-only.net>
Tobin, Some encouraging news when I tried 1.0.14rc2: This release probes and detects the codec successfully, two lines are added to syslog after modprob'ing snd-hda-intel: ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:696: codec_mask = 0x9 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:1764: hda_codec: model 'toshiba' is selected for config 1179:ff10 (Toshiba)
AND the microphone works. I ran 'arecord test.wav' and played it back successfully on another machine. However, playback is still not working on the ATI SB450... alsa-info.sh output for the rc2 test is at http://pastebin.ca/453663
Not sure whether it helps or not, but here are the lines added to syslog when I ran arecord (shortened a bit):
//Start of arecord ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:1158: azx_pcm_prepare: bufsize=0x10000, fragsize=0x1000, format=0x11 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x8, stream=0x1, channel=0, format=0x11
//End of a record ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x8, stream=0x0, channel=0, format=0x0
And these are the ones for "aplay test.wav"
//start of aplay ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/../../alsa-kernel/pci/hda/hda_intel.c:1158: azx_pcm_prepare: bufsize=0x10000, fragsize=0x1000, format=0x11 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x3, stream=0x5, channel=0, format=0x11 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x6, stream=0x5, channel=0, format=0x11 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x5, stream=0x5, channel=0, format=0x11 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x4, stream=0x5, channel=0, format=0x11
//End of aplay ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x3, stream=0x0, channel=0, format=0x0 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x6, stream=0x0, channel=0, format=0x0 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x5, stream=0x0, channel=0, format=0x0 ALSA /media/sda3/gilles_files/download/drivers/alsa-driver-1.0.14rc2/pci/hda/hda_codec.c:627: hda_codec_setup_stream: NID=0x4, stream=0x0, channel=0, format=0x0
Is hda_codec_setup_stream meant to be called different times with 4 different nids ?
participants (2)
-
Ben DiDonc -
Tobin Davis