[PATCH 1/4] ASoC: tas2764: Add post reset delays
Make sure there is at least 1 ms delay from reset to first command as is specified in the datasheet. This is a fix similar to commit 307f31452078 ("ASoC: tas2770: Insert post reset delay").
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer povik+lin@cutebit.org --- sound/soc/codecs/tas2764.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-)
diff --git a/sound/soc/codecs/tas2764.c b/sound/soc/codecs/tas2764.c index 42f0c1e449ba..039bf1900880 100644 --- a/sound/soc/codecs/tas2764.c +++ b/sound/soc/codecs/tas2764.c @@ -42,10 +42,12 @@ static void tas2764_reset(struct tas2764_priv *tas2764) gpiod_set_value_cansleep(tas2764->reset_gpio, 0); msleep(20); gpiod_set_value_cansleep(tas2764->reset_gpio, 1); + usleep_range(1000, 2000); }
snd_soc_component_write(tas2764->component, TAS2764_SW_RST, TAS2764_RST); + usleep_range(1000, 2000); }
static int tas2764_set_bias_level(struct snd_soc_component *component, @@ -107,8 +109,10 @@ static int tas2764_codec_resume(struct snd_soc_component *component) struct tas2764_priv *tas2764 = snd_soc_component_get_drvdata(component); int ret;
- if (tas2764->sdz_gpio) + if (tas2764->sdz_gpio) { gpiod_set_value_cansleep(tas2764->sdz_gpio, 1); + usleep_range(1000, 2000); + }
ret = snd_soc_component_update_bits(component, TAS2764_PWR_CTRL, TAS2764_PWR_CTRL_MASK, @@ -501,8 +505,10 @@ static int tas2764_codec_probe(struct snd_soc_component *component)
tas2764->component = component;
- if (tas2764->sdz_gpio) + if (tas2764->sdz_gpio) { gpiod_set_value_cansleep(tas2764->sdz_gpio, 1); + usleep_range(1000, 2000); + }
tas2764_reset(tas2764);
Fix setting of FSYNC polarity in case of LEFT_J and DSP_A/B formats. Do NOT set the SCFG field as was previously done, because that is not correct and is also in conflict with the "ASI1 Source" control which sets the same SCFG field!
Also add support for explicit polarity inversion.
Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer povik+lin@cutebit.org --- sound/soc/codecs/tas2764.c | 30 +++++++++++++++++------------- sound/soc/codecs/tas2764.h | 6 ++---- 2 files changed, 19 insertions(+), 17 deletions(-)
diff --git a/sound/soc/codecs/tas2764.c b/sound/soc/codecs/tas2764.c index 039bf1900880..0143a55cd33c 100644 --- a/sound/soc/codecs/tas2764.c +++ b/sound/soc/codecs/tas2764.c @@ -135,7 +135,8 @@ static const char * const tas2764_ASI1_src[] = { };
static SOC_ENUM_SINGLE_DECL( - tas2764_ASI1_src_enum, TAS2764_TDM_CFG2, 4, tas2764_ASI1_src); + tas2764_ASI1_src_enum, TAS2764_TDM_CFG2, TAS2764_TDM_CFG2_SCFG_SHIFT, + tas2764_ASI1_src);
static const struct snd_kcontrol_new tas2764_asi1_mux = SOC_DAPM_ENUM("ASI1 Source", tas2764_ASI1_src_enum); @@ -333,20 +334,22 @@ static int tas2764_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) { struct snd_soc_component *component = dai->component; struct tas2764_priv *tas2764 = snd_soc_component_get_drvdata(component); - u8 tdm_rx_start_slot = 0, asi_cfg_1 = 0; - int iface; + u8 tdm_rx_start_slot = 0, asi_cfg_0 = 0, asi_cfg_1 = 0; int ret;
switch (fmt & SND_SOC_DAIFMT_INV_MASK) { + case SND_SOC_DAIFMT_NB_IF: + asi_cfg_0 ^= TAS2764_TDM_CFG0_FRAME_START; + fallthrough; case SND_SOC_DAIFMT_NB_NF: asi_cfg_1 = TAS2764_TDM_CFG1_RX_RISING; break; + case SND_SOC_DAIFMT_IB_IF: + asi_cfg_0 ^= TAS2764_TDM_CFG0_FRAME_START; + fallthrough; case SND_SOC_DAIFMT_IB_NF: asi_cfg_1 = TAS2764_TDM_CFG1_RX_FALLING; break; - default: - dev_err(tas2764->dev, "ASI format Inverse is not found\n"); - return -EINVAL; }
ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG1, @@ -357,13 +360,13 @@ static int tas2764_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { case SND_SOC_DAIFMT_I2S: + asi_cfg_0 ^= TAS2764_TDM_CFG0_FRAME_START; + fallthrough; case SND_SOC_DAIFMT_DSP_A: - iface = TAS2764_TDM_CFG2_SCFG_I2S; tdm_rx_start_slot = 1; break; case SND_SOC_DAIFMT_DSP_B: case SND_SOC_DAIFMT_LEFT_J: - iface = TAS2764_TDM_CFG2_SCFG_LEFT_J; tdm_rx_start_slot = 0; break; default: @@ -372,14 +375,15 @@ static int tas2764_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) return -EINVAL; }
- ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG1, - TAS2764_TDM_CFG1_MASK, - (tdm_rx_start_slot << TAS2764_TDM_CFG1_51_SHIFT)); + ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG0, + TAS2764_TDM_CFG0_FRAME_START, + asi_cfg_0); if (ret < 0) return ret;
- ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG2, - TAS2764_TDM_CFG2_SCFG_MASK, iface); + ret = snd_soc_component_update_bits(component, TAS2764_TDM_CFG1, + TAS2764_TDM_CFG1_MASK, + (tdm_rx_start_slot << TAS2764_TDM_CFG1_51_SHIFT)); if (ret < 0) return ret;
diff --git a/sound/soc/codecs/tas2764.h b/sound/soc/codecs/tas2764.h index 67d6fd903c42..f015f22a083b 100644 --- a/sound/soc/codecs/tas2764.h +++ b/sound/soc/codecs/tas2764.h @@ -47,6 +47,7 @@ #define TAS2764_TDM_CFG0_MASK GENMASK(3, 1) #define TAS2764_TDM_CFG0_44_1_48KHZ BIT(3) #define TAS2764_TDM_CFG0_88_2_96KHZ (BIT(3) | BIT(1)) +#define TAS2764_TDM_CFG0_FRAME_START BIT(0)
/* TDM Configuration Reg1 */ #define TAS2764_TDM_CFG1 TAS2764_REG(0X0, 0x09) @@ -66,10 +67,7 @@ #define TAS2764_TDM_CFG2_RXS_16BITS 0x0 #define TAS2764_TDM_CFG2_RXS_24BITS BIT(0) #define TAS2764_TDM_CFG2_RXS_32BITS BIT(1) -#define TAS2764_TDM_CFG2_SCFG_MASK GENMASK(5, 4) -#define TAS2764_TDM_CFG2_SCFG_I2S 0x0 -#define TAS2764_TDM_CFG2_SCFG_LEFT_J BIT(4) -#define TAS2764_TDM_CFG2_SCFG_RIGHT_J BIT(5) +#define TAS2764_TDM_CFG2_SCFG_SHIFT 4
/* TDM Configuration Reg3 */ #define TAS2764_TDM_CFG3 TAS2764_REG(0X0, 0x0c)
From: Hector Martin marcan@marcan.st
DVC value 0xc8 is -100dB and 0xc9 is mute; this needs to map to -100.5dB as far as the dB scale is concerned. Fix that and enable the mute flag, so alsamixer correctly shows the control as <0 dB .. -100 dB, mute>.
Signed-off-by: Hector Martin marcan@marcan.st Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer povik+lin@cutebit.org --- sound/soc/codecs/tas2764.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/sound/soc/codecs/tas2764.c b/sound/soc/codecs/tas2764.c index 0143a55cd33c..55da1b3440e1 100644 --- a/sound/soc/codecs/tas2764.c +++ b/sound/soc/codecs/tas2764.c @@ -536,7 +536,7 @@ static int tas2764_codec_probe(struct snd_soc_component *component) }
static DECLARE_TLV_DB_SCALE(tas2764_digital_tlv, 1100, 50, 0); -static DECLARE_TLV_DB_SCALE(tas2764_playback_volume, -10000, 50, 0); +static DECLARE_TLV_DB_SCALE(tas2764_playback_volume, -10050, 50, 1);
static const struct snd_kcontrol_new tas2764_snd_controls[] = { SOC_SINGLE_TLV("Speaker Volume", TAS2764_DVC, 0,
From: Hector Martin marcan@marcan.st
The register default is 0x28 per the datasheet, and the amp gain field is supposed to be shifted left by one. With the wrong default, the ALSA controls lie about the power-up state. With the wrong shift, we get only half the gain we expect.
Signed-off-by: Hector Martin marcan@marcan.st Fixes: 827ed8a0fa50 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer povik+lin@cutebit.org --- sound/soc/codecs/tas2764.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/sound/soc/codecs/tas2764.c b/sound/soc/codecs/tas2764.c index 55da1b3440e1..846d9d3ecc9d 100644 --- a/sound/soc/codecs/tas2764.c +++ b/sound/soc/codecs/tas2764.c @@ -541,7 +541,7 @@ static DECLARE_TLV_DB_SCALE(tas2764_playback_volume, -10050, 50, 1); static const struct snd_kcontrol_new tas2764_snd_controls[] = { SOC_SINGLE_TLV("Speaker Volume", TAS2764_DVC, 0, TAS2764_DVC_MAX, 1, tas2764_playback_volume), - SOC_SINGLE_TLV("Amp Gain Volume", TAS2764_CHNL_0, 0, 0x14, 0, + SOC_SINGLE_TLV("Amp Gain Volume", TAS2764_CHNL_0, 1, 0x14, 0, tas2764_digital_tlv), };
@@ -565,7 +565,7 @@ static const struct reg_default tas2764_reg_defaults[] = { { TAS2764_SW_RST, 0x00 }, { TAS2764_PWR_CTRL, 0x1a }, { TAS2764_DVC, 0x00 }, - { TAS2764_CHNL_0, 0x00 }, + { TAS2764_CHNL_0, 0x28 }, { TAS2764_TDM_CFG0, 0x09 }, { TAS2764_TDM_CFG1, 0x02 }, { TAS2764_TDM_CFG2, 0x0a },
On Thu, 30 Jun 2022 09:51:32 +0200, Martin Povišer wrote:
Make sure there is at least 1 ms delay from reset to first command as is specified in the datasheet. This is a fix similar to commit 307f31452078 ("ASoC: tas2770: Insert post reset delay").
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/4] ASoC: tas2764: Add post reset delays commit: 4aeb04227eb4d5de83343cfbad00433019ccfdf5 [2/4] ASoC: tas2764: Fix and extend FSYNC polarity handling commit: a1b2cfda5616ddccd54fa10b9e72932b3f3bce8b [3/4] ASoC: tas2764: Correct playback volume range commit: aea21dbec799d63393b615b73e4708a5d036df99 [4/4] ASoC: tas2764: Fix amp gain register offset & default commit: cabcd219cee142a0f55516d2e257c8833cbd14f6
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
participants (2)
-
Mark Brown -
Martin Povišer