[alsa-devel] [PATCH 0/4] ASoC: meson: add axg spdif input support
This patchset adds the initial support the spdif input found on the axg SoC family.
The capture itself works well but the rate detection could be enhanced in the future.
Like several other drivers of this type, no check is done to verify if the rate of the input stream is consistent with the rate requested in hw_params()
The automatic rate detection mechanism of this device and the related IRQ proved difficult to work with, as documented in the driver. Several approaches to work around this minor issue have been tried but none provided a complete and reliable solution so far. Hopefully more eyes on this will help figure this out.
Since I authored all Amlogic ASoC drivers (and the related bugs) merged so far, I have added myself as maintainer of them in the last patch of this series.
Jerome Brunet (4): ASoC: meson: axg-toddr: add support for spdifin backend ASoC: meson: add axg spdif input DT binding documentation ASoC: meson: add axg spdif input MAINTAINERS: Add Amlogic sound drivers entry
.../bindings/sound/amlogic,axg-spdifin.txt | 22 + MAINTAINERS | 7 + sound/soc/meson/Kconfig | 9 +- sound/soc/meson/Makefile | 2 + sound/soc/meson/axg-fifo.h | 3 +- sound/soc/meson/axg-spdifin.c | 521 ++++++++++++++++++ sound/soc/meson/axg-toddr.c | 15 +- 7 files changed, 567 insertions(+), 12 deletions(-) create mode 100644 Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt create mode 100644 sound/soc/meson/axg-spdifin.c
add IEC958_SUBFRAME_LE to the list of format accepted by the fifo frontend.
As opposed to what was initially noted in the toddr dai driver, the spdifin does not place the msb at bit 28, it just output a whole spdif subframe.
Placing the msb at bit 28 in the toddr driver just filters out the parity, user, channel status and validity bits. It is better to just provide the whole spdif subframe to the userspace and let the iec958 plugin deal with it.
Signed-off-by: Jerome Brunet jbrunet@baylibre.com --- sound/soc/meson/axg-fifo.h | 3 ++- sound/soc/meson/axg-toddr.c | 15 +++++---------- 2 files changed, 7 insertions(+), 11 deletions(-)
diff --git a/sound/soc/meson/axg-fifo.h b/sound/soc/meson/axg-fifo.h index cb6c4013ca33..d9f516cfbeda 100644 --- a/sound/soc/meson/axg-fifo.h +++ b/sound/soc/meson/axg-fifo.h @@ -25,7 +25,8 @@ struct snd_soc_pcm_runtime; SNDRV_PCM_FMTBIT_S16_LE | \ SNDRV_PCM_FMTBIT_S20_LE | \ SNDRV_PCM_FMTBIT_S24_LE | \ - SNDRV_PCM_FMTBIT_S32_LE) + SNDRV_PCM_FMTBIT_S32_LE | \ + SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_LE)
#define AXG_FIFO_BURST 8 #define AXG_FIFO_MIN_CNT 64 diff --git a/sound/soc/meson/axg-toddr.c b/sound/soc/meson/axg-toddr.c index c2c9bb312586..0e9ca3882ae5 100644 --- a/sound/soc/meson/axg-toddr.c +++ b/sound/soc/meson/axg-toddr.c @@ -25,6 +25,8 @@ #define CTRL0_TODDR_LSB_POS_MASK GENMASK(7, 3) #define CTRL0_TODDR_LSB_POS(x) ((x) << 3)
+#define TODDR_MSB_POS 31 + static int axg_toddr_pcm_new(struct snd_soc_pcm_runtime *rtd, struct snd_soc_dai *dai) { @@ -36,14 +38,7 @@ static int axg_toddr_dai_hw_params(struct snd_pcm_substream *substream, struct snd_soc_dai *dai) { struct axg_fifo *fifo = snd_soc_dai_get_drvdata(dai); - unsigned int type, width, msb = 31; - - /* - * NOTE: - * Almost all backend will place the MSB at bit 31, except SPDIF Input - * which will put it at index 28. When adding support for the SPDIF - * Input, we'll need to find which type of backend we are connected to. - */ + unsigned int type, width;
switch (params_physical_width(params)) { case 8: @@ -66,8 +61,8 @@ static int axg_toddr_dai_hw_params(struct snd_pcm_substream *substream, CTRL0_TODDR_MSB_POS_MASK | CTRL0_TODDR_LSB_POS_MASK, CTRL0_TODDR_TYPE(type) | - CTRL0_TODDR_MSB_POS(msb) | - CTRL0_TODDR_LSB_POS(msb - (width - 1))); + CTRL0_TODDR_MSB_POS(TODDR_MSB_POS) | + CTRL0_TODDR_LSB_POS(TODDR_MSB_POS - (width - 1)));
return 0; }
The patch
ASoC: meson: axg-toddr: add support for spdifin backend
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
From 984463a94d5cb23120bfe7d689077b940c25128b Mon Sep 17 00:00:00 2001
From: Jerome Brunet jbrunet@baylibre.com Date: Tue, 11 Dec 2018 14:47:10 +0100 Subject: [PATCH] ASoC: meson: axg-toddr: add support for spdifin backend
add IEC958_SUBFRAME_LE to the list of format accepted by the fifo frontend.
As opposed to what was initially noted in the toddr dai driver, the spdifin does not place the msb at bit 28, it just output a whole spdif subframe.
Placing the msb at bit 28 in the toddr driver just filters out the parity, user, channel status and validity bits. It is better to just provide the whole spdif subframe to the userspace and let the iec958 plugin deal with it.
Signed-off-by: Jerome Brunet jbrunet@baylibre.com Signed-off-by: Mark Brown broonie@kernel.org --- sound/soc/meson/axg-fifo.h | 3 ++- sound/soc/meson/axg-toddr.c | 15 +++++---------- 2 files changed, 7 insertions(+), 11 deletions(-)
diff --git a/sound/soc/meson/axg-fifo.h b/sound/soc/meson/axg-fifo.h index cb6c4013ca33..d9f516cfbeda 100644 --- a/sound/soc/meson/axg-fifo.h +++ b/sound/soc/meson/axg-fifo.h @@ -25,7 +25,8 @@ struct snd_soc_pcm_runtime; SNDRV_PCM_FMTBIT_S16_LE | \ SNDRV_PCM_FMTBIT_S20_LE | \ SNDRV_PCM_FMTBIT_S24_LE | \ - SNDRV_PCM_FMTBIT_S32_LE) + SNDRV_PCM_FMTBIT_S32_LE | \ + SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_LE)
#define AXG_FIFO_BURST 8 #define AXG_FIFO_MIN_CNT 64 diff --git a/sound/soc/meson/axg-toddr.c b/sound/soc/meson/axg-toddr.c index c2c9bb312586..0e9ca3882ae5 100644 --- a/sound/soc/meson/axg-toddr.c +++ b/sound/soc/meson/axg-toddr.c @@ -25,6 +25,8 @@ #define CTRL0_TODDR_LSB_POS_MASK GENMASK(7, 3) #define CTRL0_TODDR_LSB_POS(x) ((x) << 3)
+#define TODDR_MSB_POS 31 + static int axg_toddr_pcm_new(struct snd_soc_pcm_runtime *rtd, struct snd_soc_dai *dai) { @@ -36,14 +38,7 @@ static int axg_toddr_dai_hw_params(struct snd_pcm_substream *substream, struct snd_soc_dai *dai) { struct axg_fifo *fifo = snd_soc_dai_get_drvdata(dai); - unsigned int type, width, msb = 31; - - /* - * NOTE: - * Almost all backend will place the MSB at bit 31, except SPDIF Input - * which will put it at index 28. When adding support for the SPDIF - * Input, we'll need to find which type of backend we are connected to. - */ + unsigned int type, width;
switch (params_physical_width(params)) { case 8: @@ -66,8 +61,8 @@ static int axg_toddr_dai_hw_params(struct snd_pcm_substream *substream, CTRL0_TODDR_MSB_POS_MASK | CTRL0_TODDR_LSB_POS_MASK, CTRL0_TODDR_TYPE(type) | - CTRL0_TODDR_MSB_POS(msb) | - CTRL0_TODDR_LSB_POS(msb - (width - 1))); + CTRL0_TODDR_MSB_POS(TODDR_MSB_POS) | + CTRL0_TODDR_LSB_POS(TODDR_MSB_POS - (width - 1)));
return 0; }
Add the DT binding documentation for axg's SPDIF input.
Signed-off-by: Jerome Brunet jbrunet@baylibre.com --- .../bindings/sound/amlogic,axg-spdifin.txt | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt
diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt new file mode 100644 index 000000000000..2e6cb7d9b202 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt @@ -0,0 +1,22 @@ +* Amlogic Audio SPDIF Input + +Required properties: +- compatible: 'amlogic,axg-spdifin' +- interrupts: interrupt specifier for the spdif input. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "refclk" : spdif input reference clock +- #sound-dai-cells: must be 0. + +Example on the A113 SoC: + +spdifin: audio-controller@400 { + compatible = "amlogic,axg-spdifin"; + reg = <0x0 0x400 0x0 0x30>; + #sound-dai-cells = <0>; + interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc_audio AUD_CLKID_SPDIFIN>, + <&clkc_audio AUD_CLKID_SPDIFIN_CLK>; + clock-names = "pclk", "refclk"; +};
The patch
ASoC: meson: add axg spdif input DT binding documentation
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
From 18dc4665fb6f3bb617c2e6d7da3f19586d06ab17 Mon Sep 17 00:00:00 2001
From: Jerome Brunet jbrunet@baylibre.com Date: Tue, 11 Dec 2018 14:47:11 +0100 Subject: [PATCH] ASoC: meson: add axg spdif input DT binding documentation
Add the DT binding documentation for axg's SPDIF input.
Signed-off-by: Jerome Brunet jbrunet@baylibre.com Signed-off-by: Mark Brown broonie@kernel.org --- .../bindings/sound/amlogic,axg-spdifin.txt | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt
diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt new file mode 100644 index 000000000000..2e6cb7d9b202 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/amlogic,axg-spdifin.txt @@ -0,0 +1,22 @@ +* Amlogic Audio SPDIF Input + +Required properties: +- compatible: 'amlogic,axg-spdifin' +- interrupts: interrupt specifier for the spdif input. +- clocks: list of clock phandle, one for each entry clock-names. +- clock-names: should contain the following: + * "pclk" : peripheral clock. + * "refclk" : spdif input reference clock +- #sound-dai-cells: must be 0. + +Example on the A113 SoC: + +spdifin: audio-controller@400 { + compatible = "amlogic,axg-spdifin"; + reg = <0x0 0x400 0x0 0x30>; + #sound-dai-cells = <0>; + interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkc_audio AUD_CLKID_SPDIFIN>, + <&clkc_audio AUD_CLKID_SPDIFIN_CLK>; + clock-names = "pclk", "refclk"; +};
Add support for the spdif input decoder of the axg SoC family
Signed-off-by: Jerome Brunet jbrunet@baylibre.com --- sound/soc/meson/Kconfig | 9 +- sound/soc/meson/Makefile | 2 + sound/soc/meson/axg-spdifin.c | 521 ++++++++++++++++++++++++++++++++++ 3 files changed, 531 insertions(+), 1 deletion(-) create mode 100644 sound/soc/meson/axg-spdifin.c
diff --git a/sound/soc/meson/Kconfig b/sound/soc/meson/Kconfig index 8b8426ed2363..8779fe23671d 100644 --- a/sound/soc/meson/Kconfig +++ b/sound/soc/meson/Kconfig @@ -54,6 +54,7 @@ config SND_MESON_AXG_SOUND_CARD imply SND_MESON_AXG_TDMIN imply SND_MESON_AXG_TDMOUT imply SND_MESON_AXG_SPDIFOUT + imply SND_MESON_AXG_SPDIFIN imply SND_MESON_AXG_PDM help Select Y or M to add support for the AXG SoC sound card @@ -67,6 +68,13 @@ config SND_MESON_AXG_SPDIFOUT Select Y or M to add support for SPDIF output serializer embedded in the Amlogic AXG SoC family
+config SND_MESON_AXG_SPDIFIN + tristate "Amlogic AXG SPDIF Input Support" + imply SND_SOC_SPDIF + help + Select Y or M to add support for SPDIF input embedded + in the Amlogic AXG SoC family + config SND_MESON_AXG_PDM tristate "Amlogic AXG PDM Input Support" imply SND_SOC_DMIC @@ -74,5 +82,4 @@ config SND_MESON_AXG_PDM help Select Y or M to add support for PDM input embedded in the Amlogic AXG SoC family - endmenu diff --git a/sound/soc/meson/Makefile b/sound/soc/meson/Makefile index 4cd25104029d..b45dfb9e2f88 100644 --- a/sound/soc/meson/Makefile +++ b/sound/soc/meson/Makefile @@ -8,6 +8,7 @@ snd-soc-meson-axg-tdm-interface-objs := axg-tdm-interface.o snd-soc-meson-axg-tdmin-objs := axg-tdmin.o snd-soc-meson-axg-tdmout-objs := axg-tdmout.o snd-soc-meson-axg-sound-card-objs := axg-card.o +snd-soc-meson-axg-spdifin-objs := axg-spdifin.o snd-soc-meson-axg-spdifout-objs := axg-spdifout.o snd-soc-meson-axg-pdm-objs := axg-pdm.o
@@ -19,5 +20,6 @@ obj-$(CONFIG_SND_MESON_AXG_TDM_INTERFACE) += snd-soc-meson-axg-tdm-interface.o obj-$(CONFIG_SND_MESON_AXG_TDMIN) += snd-soc-meson-axg-tdmin.o obj-$(CONFIG_SND_MESON_AXG_TDMOUT) += snd-soc-meson-axg-tdmout.o obj-$(CONFIG_SND_MESON_AXG_SOUND_CARD) += snd-soc-meson-axg-sound-card.o +obj-$(CONFIG_SND_MESON_AXG_SPDIFIN) += snd-soc-meson-axg-spdifin.o obj-$(CONFIG_SND_MESON_AXG_SPDIFOUT) += snd-soc-meson-axg-spdifout.o obj-$(CONFIG_SND_MESON_AXG_PDM) += snd-soc-meson-axg-pdm.o diff --git a/sound/soc/meson/axg-spdifin.c b/sound/soc/meson/axg-spdifin.c new file mode 100644 index 000000000000..09f385a2bbba --- /dev/null +++ b/sound/soc/meson/axg-spdifin.c @@ -0,0 +1,521 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Copyright (c) 2018 BayLibre, SAS. +// Author: Jerome Brunet jbrunet@baylibre.com + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/of_platform.h> +#include <linux/regmap.h> +#include <sound/soc.h> +#include <sound/soc-dai.h> +#include <sound/pcm_params.h> + +#define SPDIFIN_CTRL0 0x00 +#define SPDIFIN_CTRL0_EN BIT(31) +#define SPDIFIN_CTRL0_RST_OUT BIT(29) +#define SPDIFIN_CTRL0_RST_IN BIT(28) +#define SPDIFIN_CTRL0_WIDTH_SEL BIT(24) +#define SPDIFIN_CTRL0_STATUS_CH_SHIFT 11 +#define SPDIFIN_CTRL0_STATUS_SEL GENMASK(10, 8) +#define SPDIFIN_CTRL0_SRC_SEL GENMASK(5, 4) +#define SPDIFIN_CTRL0_CHK_VALID BIT(3) +#define SPDIFIN_CTRL1 0x04 +#define SPDIFIN_CTRL1_BASE_TIMER GENMASK(19, 0) +#define SPDIFIN_CTRL1_IRQ_MASK GENMASK(27, 20) +#define SPDIFIN_CTRL2 0x08 +#define SPDIFIN_THRES_PER_REG 3 +#define SPDIFIN_THRES_WIDTH 10 +#define SPDIFIN_CTRL3 0x0c +#define SPDIFIN_CTRL4 0x10 +#define SPDIFIN_TIMER_PER_REG 4 +#define SPDIFIN_TIMER_WIDTH 8 +#define SPDIFIN_CTRL5 0x14 +#define SPDIFIN_CTRL6 0x18 +#define SPDIFIN_STAT0 0x1c +#define SPDIFIN_STAT0_MODE GENMASK(30, 28) +#define SPDIFIN_STAT0_MAXW GENMASK(17, 8) +#define SPDIFIN_STAT0_IRQ GENMASK(7, 0) +#define SPDIFIN_IRQ_MODE_CHANGED BIT(2) +#define SPDIFIN_STAT1 0x20 +#define SPDIFIN_STAT2 0x24 +#define SPDIFIN_MUTE_VAL 0x28 + +#define SPDIFIN_MODE_NUM 7 + +struct axg_spdifin_cfg { + const unsigned int *mode_rates; + unsigned int ref_rate; +}; + +struct axg_spdifin { + const struct axg_spdifin_cfg *conf; + struct regmap *map; + struct clk *refclk; + struct clk *pclk; +}; + +/* + * TODO: + * It would have been nice to check the actual rate against the sample rate + * requested in hw_params(). Unfortunately, I was not able to make the mode + * detection and IRQ work reliably: + * + * 1. IRQs are generated on mode change only, so there is no notification + * on transition between no signal and mode 0 (32kHz). + * 2. Mode detection very often has glitches, and may detects the + * lowest or the highest mode before zeroing in on the actual mode. + * + * This makes calling snd_pcm_stop() difficult to get right. Even notifying + * the kcontrol would be very unreliable at this point. + * Let's keep things simple until the magic spell that makes this work is + * found. + */ + +static unsigned int axg_spdifin_get_rate(struct axg_spdifin *priv) +{ + unsigned int stat, mode, rate = 0; + + regmap_read(priv->map, SPDIFIN_STAT0, &stat); + mode = FIELD_GET(SPDIFIN_STAT0_MODE, stat); + + /* + * If max width is zero, we are not capturing anything. + * Also Sometimes, when the capture is on but there is no data, + * mode is SPDIFIN_MODE_NUM, but not always ... + */ + if (FIELD_GET(SPDIFIN_STAT0_MAXW, stat) && + mode < SPDIFIN_MODE_NUM) + rate = priv->conf->mode_rates[mode]; + + return rate; +} + +static int axg_spdifin_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + + /* Apply both reset */ + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_RST_OUT | + SPDIFIN_CTRL0_RST_IN, + 0); + + /* Clear out reset before in reset */ + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_RST_OUT, SPDIFIN_CTRL0_RST_OUT); + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_RST_IN, SPDIFIN_CTRL0_RST_IN); + + return 0; +} + +static int axg_spdifin_startup(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = clk_prepare_enable(priv->refclk); + if (ret) { + dev_err(dai->dev, + "failed to enable spdifin reference clock\n"); + return ret; + } + + regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN, + SPDIFIN_CTRL0_EN); + + return 0; +} + +static void axg_spdifin_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + + regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN, 0); + clk_disable_unprepare(priv->refclk); +} + +static void axg_spdifin_write_mode_param(struct regmap *map, int mode, + unsigned int val, + unsigned int num_per_reg, + unsigned int base_reg, + unsigned int width) +{ + unsigned int offset = mode, rem; + unsigned int reg, shift; + + rem = do_div(offset, num_per_reg); + + reg = offset * regmap_get_reg_stride(map) + base_reg; + shift = width * (num_per_reg - 1 - rem); + + regmap_update_bits(map, reg, GENMASK(width - 1, 0) << shift, + val << shift); +} + +static void axg_spdifin_write_timer(struct regmap *map, int mode, + unsigned int val) +{ + axg_spdifin_write_mode_param(map, mode, val, SPDIFIN_TIMER_PER_REG, + SPDIFIN_CTRL4, SPDIFIN_TIMER_WIDTH); +} + +static void axg_spdifin_write_threshold(struct regmap *map, int mode, + unsigned int val) +{ + axg_spdifin_write_mode_param(map, mode, val, SPDIFIN_THRES_PER_REG, + SPDIFIN_CTRL2, SPDIFIN_THRES_WIDTH); +} + +static unsigned int axg_spdifin_mode_timer(struct axg_spdifin *priv, + int mode, + unsigned int rate) +{ + /* + * Number of period of the reference clock during a period of the + * input signal reference clock + */ + return rate / (128 * priv->conf->mode_rates[mode]); +} + +static int axg_spdifin_sample_mode_config(struct snd_soc_dai *dai, + struct axg_spdifin *priv) +{ + unsigned int rate, t_next; + int ret, i = SPDIFIN_MODE_NUM - 1; + + /* Set spdif input reference clock */ + ret = clk_set_rate(priv->refclk, priv->conf->ref_rate); + if (ret) { + dev_err(dai->dev, "reference clock rate set failed\n"); + return ret; + } + + /* + * The rate actually set might be slightly different, get + * the actual rate for the following mode calculation + */ + rate = clk_get_rate(priv->refclk); + + /* HW will update mode every 1ms */ + regmap_update_bits(priv->map, SPDIFIN_CTRL1, + SPDIFIN_CTRL1_BASE_TIMER, + FIELD_PREP(SPDIFIN_CTRL1_BASE_TIMER, rate / 1000)); + + /* Threshold based on the minimum width between two edges */ + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_WIDTH_SEL, SPDIFIN_CTRL0_WIDTH_SEL); + + /* Calculate the last timer which has no threshold */ + t_next = axg_spdifin_mode_timer(priv, i, rate); + axg_spdifin_write_timer(priv->map, i, t_next); + + do { + unsigned int t; + + i -= 1; + + /* Calculate the timer */ + t = axg_spdifin_mode_timer(priv, i, rate); + + /* Set the timer value */ + axg_spdifin_write_timer(priv->map, i, t); + + /* Set the threshold value */ + axg_spdifin_write_threshold(priv->map, i, t + t_next); + + /* Save the current timer for the next threshold calculation */ + t_next = t; + + } while (i > 0); + + return 0; +} + +static int axg_spdifin_dai_probe(struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = clk_prepare_enable(priv->pclk); + if (ret) { + dev_err(dai->dev, "failed to enable pclk\n"); + return ret; + } + + ret = axg_spdifin_sample_mode_config(dai, priv); + if (ret) { + dev_err(dai->dev, "mode configuration failed\n"); + clk_disable_unprepare(priv->pclk); + return ret; + } + + return 0; +} + +static int axg_spdifin_dai_remove(struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + + clk_disable_unprepare(priv->pclk); + return 0; +} + +static const struct snd_soc_dai_ops axg_spdifin_ops = { + .prepare = axg_spdifin_prepare, + .startup = axg_spdifin_startup, + .shutdown = axg_spdifin_shutdown, +}; + +static int axg_spdifin_iec958_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958; + uinfo->count = 1; + + return 0; +} + +static int axg_spdifin_get_status_mask(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + int i; + + for (i = 0; i < 24; i++) + ucontrol->value.iec958.status[i] = 0xff; + + return 0; +} + +static int axg_spdifin_get_status(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *c = snd_kcontrol_chip(kcontrol); + struct axg_spdifin *priv = snd_soc_component_get_drvdata(c); + int i, j; + + for (i = 0; i < 6; i++) { + unsigned int val; + + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_STATUS_SEL, + FIELD_PREP(SPDIFIN_CTRL0_STATUS_SEL, i)); + + regmap_read(priv->map, SPDIFIN_STAT1, &val); + + for (j = 0; j < 4; j++) { + unsigned int offset = i * 4 + j; + + ucontrol->value.iec958.status[offset] = + (val >> (j * 8)) & 0xff; + } + } + + return 0; +} + +#define AXG_SPDIFIN_IEC958_MASK \ + { \ + .access = SNDRV_CTL_ELEM_ACCESS_READ, \ + .iface = SNDRV_CTL_ELEM_IFACE_PCM, \ + .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, MASK), \ + .info = axg_spdifin_iec958_info, \ + .get = axg_spdifin_get_status_mask, \ + } + +#define AXG_SPDIFIN_IEC958_STATUS \ + { \ + .access = (SNDRV_CTL_ELEM_ACCESS_READ | \ + SNDRV_CTL_ELEM_ACCESS_VOLATILE), \ + .iface = SNDRV_CTL_ELEM_IFACE_PCM, \ + .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, NONE), \ + .info = axg_spdifin_iec958_info, \ + .get = axg_spdifin_get_status, \ + } + +static const char * const spdifin_chsts_src_texts[] = { + "A", "B", +}; + +static SOC_ENUM_SINGLE_DECL(axg_spdifin_chsts_src_enum, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_STATUS_CH_SHIFT, + spdifin_chsts_src_texts); + +static int axg_spdifin_rate_lock_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = 192000; + + return 0; +} + +static int axg_spdifin_rate_lock_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *c = snd_kcontrol_chip(kcontrol); + struct axg_spdifin *priv = snd_soc_component_get_drvdata(c); + + ucontrol->value.integer.value[0] = axg_spdifin_get_rate(priv); + + return 0; +} + +#define AXG_SPDIFIN_LOCK_RATE(xname) \ + { \ + .iface = SNDRV_CTL_ELEM_IFACE_PCM, \ + .access = (SNDRV_CTL_ELEM_ACCESS_READ | \ + SNDRV_CTL_ELEM_ACCESS_VOLATILE), \ + .get = axg_spdifin_rate_lock_get, \ + .info = axg_spdifin_rate_lock_info, \ + .name = xname, \ + } + +static const struct snd_kcontrol_new axg_spdifin_controls[] = { + AXG_SPDIFIN_LOCK_RATE("Capture Rate Lock"), + SOC_DOUBLE("Capture Switch", SPDIFIN_CTRL0, 7, 6, 1, 1), + SOC_ENUM(SNDRV_CTL_NAME_IEC958("", CAPTURE, NONE) "Src", + axg_spdifin_chsts_src_enum), + AXG_SPDIFIN_IEC958_MASK, + AXG_SPDIFIN_IEC958_STATUS, +}; + +static const struct snd_soc_component_driver axg_spdifin_component_drv = { + .controls = axg_spdifin_controls, + .num_controls = ARRAY_SIZE(axg_spdifin_controls), +}; + +static const struct regmap_config axg_spdifin_regmap_cfg = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = SPDIFIN_MUTE_VAL, +}; + +static const unsigned int axg_spdifin_mode_rates[SPDIFIN_MODE_NUM] = { + 32000, 44100, 48000, 88200, 96000, 176400, 192000, +}; + +static const struct axg_spdifin_cfg axg_cfg = { + .mode_rates = axg_spdifin_mode_rates, + .ref_rate = 333333333, +}; + +static const struct of_device_id axg_spdifin_of_match[] = { + { + .compatible = "amlogic,axg-spdifin", + .data = &axg_cfg, + }, {} +}; +MODULE_DEVICE_TABLE(of, axg_spdifin_of_match); + +static struct snd_soc_dai_driver * +axg_spdifin_get_dai_drv(struct device *dev, struct axg_spdifin *priv) +{ + struct snd_soc_dai_driver *drv; + int i; + + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL); + if (!drv) + return ERR_PTR(-ENOMEM); + + drv->name = "SPDIF Input"; + drv->ops = &axg_spdifin_ops; + drv->probe = axg_spdifin_dai_probe; + drv->remove = axg_spdifin_dai_remove; + drv->capture.stream_name = "Capture"; + drv->capture.channels_min = 1; + drv->capture.channels_max = 2; + drv->capture.formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_LE; + + for (i = 0; i < SPDIFIN_MODE_NUM; i++) { + unsigned int rb = + snd_pcm_rate_to_rate_bit(priv->conf->mode_rates[i]); + + if (rb == SNDRV_PCM_RATE_KNOT) + return ERR_PTR(-EINVAL); + + drv->capture.rates |= rb; + } + + return drv; +} + +static int axg_spdifin_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct axg_spdifin *priv; + struct snd_soc_dai_driver *dai_drv; + struct resource *res; + void __iomem *regs; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + platform_set_drvdata(pdev, priv); + + priv->conf = of_device_get_match_data(dev); + if (!priv->conf) { + dev_err(dev, "failed to match device\n"); + return -ENODEV; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + regs = devm_ioremap_resource(dev, res); + if (IS_ERR(regs)) + return PTR_ERR(regs); + + priv->map = devm_regmap_init_mmio(dev, regs, &axg_spdifin_regmap_cfg); + if (IS_ERR(priv->map)) { + dev_err(dev, "failed to init regmap: %ld\n", + PTR_ERR(priv->map)); + return PTR_ERR(priv->map); + } + + priv->pclk = devm_clk_get(dev, "pclk"); + if (IS_ERR(priv->pclk)) { + ret = PTR_ERR(priv->pclk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get pclk: %d\n", ret); + return ret; + } + + priv->refclk = devm_clk_get(dev, "refclk"); + if (IS_ERR(priv->refclk)) { + ret = PTR_ERR(priv->refclk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get mclk: %d\n", ret); + return ret; + } + + dai_drv = axg_spdifin_get_dai_drv(dev, priv); + if (IS_ERR(dai_drv)) { + dev_err(dev, "failed to get dai driver: %ld\n", + PTR_ERR(dai_drv)); + return PTR_ERR(dai_drv); + } + + return devm_snd_soc_register_component(dev, &axg_spdifin_component_drv, + dai_drv, 1); +} + +static struct platform_driver axg_spdifin_pdrv = { + .probe = axg_spdifin_probe, + .driver = { + .name = "axg-spdifin", + .of_match_table = axg_spdifin_of_match, + }, +}; +module_platform_driver(axg_spdifin_pdrv); + +MODULE_DESCRIPTION("Amlogic AXG SPDIF Input driver"); +MODULE_AUTHOR("Jerome Brunet jbrunet@baylibre.com"); +MODULE_LICENSE("GPL v2");
The patch
ASoC: meson: add axg spdif input
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
From 5ce5658375e6de2468c4884f7ae474c4ed40a13f Mon Sep 17 00:00:00 2001
From: Jerome Brunet jbrunet@baylibre.com Date: Tue, 11 Dec 2018 14:47:12 +0100 Subject: [PATCH] ASoC: meson: add axg spdif input
Add support for the spdif input decoder of the axg SoC family
Signed-off-by: Jerome Brunet jbrunet@baylibre.com Signed-off-by: Mark Brown broonie@kernel.org --- sound/soc/meson/Kconfig | 9 +- sound/soc/meson/Makefile | 2 + sound/soc/meson/axg-spdifin.c | 521 ++++++++++++++++++++++++++++++++++ 3 files changed, 531 insertions(+), 1 deletion(-) create mode 100644 sound/soc/meson/axg-spdifin.c
diff --git a/sound/soc/meson/Kconfig b/sound/soc/meson/Kconfig index 8b8426ed2363..8779fe23671d 100644 --- a/sound/soc/meson/Kconfig +++ b/sound/soc/meson/Kconfig @@ -54,6 +54,7 @@ config SND_MESON_AXG_SOUND_CARD imply SND_MESON_AXG_TDMIN imply SND_MESON_AXG_TDMOUT imply SND_MESON_AXG_SPDIFOUT + imply SND_MESON_AXG_SPDIFIN imply SND_MESON_AXG_PDM help Select Y or M to add support for the AXG SoC sound card @@ -67,6 +68,13 @@ config SND_MESON_AXG_SPDIFOUT Select Y or M to add support for SPDIF output serializer embedded in the Amlogic AXG SoC family
+config SND_MESON_AXG_SPDIFIN + tristate "Amlogic AXG SPDIF Input Support" + imply SND_SOC_SPDIF + help + Select Y or M to add support for SPDIF input embedded + in the Amlogic AXG SoC family + config SND_MESON_AXG_PDM tristate "Amlogic AXG PDM Input Support" imply SND_SOC_DMIC @@ -74,5 +82,4 @@ config SND_MESON_AXG_PDM help Select Y or M to add support for PDM input embedded in the Amlogic AXG SoC family - endmenu diff --git a/sound/soc/meson/Makefile b/sound/soc/meson/Makefile index 4cd25104029d..b45dfb9e2f88 100644 --- a/sound/soc/meson/Makefile +++ b/sound/soc/meson/Makefile @@ -8,6 +8,7 @@ snd-soc-meson-axg-tdm-interface-objs := axg-tdm-interface.o snd-soc-meson-axg-tdmin-objs := axg-tdmin.o snd-soc-meson-axg-tdmout-objs := axg-tdmout.o snd-soc-meson-axg-sound-card-objs := axg-card.o +snd-soc-meson-axg-spdifin-objs := axg-spdifin.o snd-soc-meson-axg-spdifout-objs := axg-spdifout.o snd-soc-meson-axg-pdm-objs := axg-pdm.o
@@ -19,5 +20,6 @@ obj-$(CONFIG_SND_MESON_AXG_TDM_INTERFACE) += snd-soc-meson-axg-tdm-interface.o obj-$(CONFIG_SND_MESON_AXG_TDMIN) += snd-soc-meson-axg-tdmin.o obj-$(CONFIG_SND_MESON_AXG_TDMOUT) += snd-soc-meson-axg-tdmout.o obj-$(CONFIG_SND_MESON_AXG_SOUND_CARD) += snd-soc-meson-axg-sound-card.o +obj-$(CONFIG_SND_MESON_AXG_SPDIFIN) += snd-soc-meson-axg-spdifin.o obj-$(CONFIG_SND_MESON_AXG_SPDIFOUT) += snd-soc-meson-axg-spdifout.o obj-$(CONFIG_SND_MESON_AXG_PDM) += snd-soc-meson-axg-pdm.o diff --git a/sound/soc/meson/axg-spdifin.c b/sound/soc/meson/axg-spdifin.c new file mode 100644 index 000000000000..09f385a2bbba --- /dev/null +++ b/sound/soc/meson/axg-spdifin.c @@ -0,0 +1,521 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +// +// Copyright (c) 2018 BayLibre, SAS. +// Author: Jerome Brunet jbrunet@baylibre.com + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/of_platform.h> +#include <linux/regmap.h> +#include <sound/soc.h> +#include <sound/soc-dai.h> +#include <sound/pcm_params.h> + +#define SPDIFIN_CTRL0 0x00 +#define SPDIFIN_CTRL0_EN BIT(31) +#define SPDIFIN_CTRL0_RST_OUT BIT(29) +#define SPDIFIN_CTRL0_RST_IN BIT(28) +#define SPDIFIN_CTRL0_WIDTH_SEL BIT(24) +#define SPDIFIN_CTRL0_STATUS_CH_SHIFT 11 +#define SPDIFIN_CTRL0_STATUS_SEL GENMASK(10, 8) +#define SPDIFIN_CTRL0_SRC_SEL GENMASK(5, 4) +#define SPDIFIN_CTRL0_CHK_VALID BIT(3) +#define SPDIFIN_CTRL1 0x04 +#define SPDIFIN_CTRL1_BASE_TIMER GENMASK(19, 0) +#define SPDIFIN_CTRL1_IRQ_MASK GENMASK(27, 20) +#define SPDIFIN_CTRL2 0x08 +#define SPDIFIN_THRES_PER_REG 3 +#define SPDIFIN_THRES_WIDTH 10 +#define SPDIFIN_CTRL3 0x0c +#define SPDIFIN_CTRL4 0x10 +#define SPDIFIN_TIMER_PER_REG 4 +#define SPDIFIN_TIMER_WIDTH 8 +#define SPDIFIN_CTRL5 0x14 +#define SPDIFIN_CTRL6 0x18 +#define SPDIFIN_STAT0 0x1c +#define SPDIFIN_STAT0_MODE GENMASK(30, 28) +#define SPDIFIN_STAT0_MAXW GENMASK(17, 8) +#define SPDIFIN_STAT0_IRQ GENMASK(7, 0) +#define SPDIFIN_IRQ_MODE_CHANGED BIT(2) +#define SPDIFIN_STAT1 0x20 +#define SPDIFIN_STAT2 0x24 +#define SPDIFIN_MUTE_VAL 0x28 + +#define SPDIFIN_MODE_NUM 7 + +struct axg_spdifin_cfg { + const unsigned int *mode_rates; + unsigned int ref_rate; +}; + +struct axg_spdifin { + const struct axg_spdifin_cfg *conf; + struct regmap *map; + struct clk *refclk; + struct clk *pclk; +}; + +/* + * TODO: + * It would have been nice to check the actual rate against the sample rate + * requested in hw_params(). Unfortunately, I was not able to make the mode + * detection and IRQ work reliably: + * + * 1. IRQs are generated on mode change only, so there is no notification + * on transition between no signal and mode 0 (32kHz). + * 2. Mode detection very often has glitches, and may detects the + * lowest or the highest mode before zeroing in on the actual mode. + * + * This makes calling snd_pcm_stop() difficult to get right. Even notifying + * the kcontrol would be very unreliable at this point. + * Let's keep things simple until the magic spell that makes this work is + * found. + */ + +static unsigned int axg_spdifin_get_rate(struct axg_spdifin *priv) +{ + unsigned int stat, mode, rate = 0; + + regmap_read(priv->map, SPDIFIN_STAT0, &stat); + mode = FIELD_GET(SPDIFIN_STAT0_MODE, stat); + + /* + * If max width is zero, we are not capturing anything. + * Also Sometimes, when the capture is on but there is no data, + * mode is SPDIFIN_MODE_NUM, but not always ... + */ + if (FIELD_GET(SPDIFIN_STAT0_MAXW, stat) && + mode < SPDIFIN_MODE_NUM) + rate = priv->conf->mode_rates[mode]; + + return rate; +} + +static int axg_spdifin_prepare(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + + /* Apply both reset */ + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_RST_OUT | + SPDIFIN_CTRL0_RST_IN, + 0); + + /* Clear out reset before in reset */ + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_RST_OUT, SPDIFIN_CTRL0_RST_OUT); + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_RST_IN, SPDIFIN_CTRL0_RST_IN); + + return 0; +} + +static int axg_spdifin_startup(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = clk_prepare_enable(priv->refclk); + if (ret) { + dev_err(dai->dev, + "failed to enable spdifin reference clock\n"); + return ret; + } + + regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN, + SPDIFIN_CTRL0_EN); + + return 0; +} + +static void axg_spdifin_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + + regmap_update_bits(priv->map, SPDIFIN_CTRL0, SPDIFIN_CTRL0_EN, 0); + clk_disable_unprepare(priv->refclk); +} + +static void axg_spdifin_write_mode_param(struct regmap *map, int mode, + unsigned int val, + unsigned int num_per_reg, + unsigned int base_reg, + unsigned int width) +{ + unsigned int offset = mode, rem; + unsigned int reg, shift; + + rem = do_div(offset, num_per_reg); + + reg = offset * regmap_get_reg_stride(map) + base_reg; + shift = width * (num_per_reg - 1 - rem); + + regmap_update_bits(map, reg, GENMASK(width - 1, 0) << shift, + val << shift); +} + +static void axg_spdifin_write_timer(struct regmap *map, int mode, + unsigned int val) +{ + axg_spdifin_write_mode_param(map, mode, val, SPDIFIN_TIMER_PER_REG, + SPDIFIN_CTRL4, SPDIFIN_TIMER_WIDTH); +} + +static void axg_spdifin_write_threshold(struct regmap *map, int mode, + unsigned int val) +{ + axg_spdifin_write_mode_param(map, mode, val, SPDIFIN_THRES_PER_REG, + SPDIFIN_CTRL2, SPDIFIN_THRES_WIDTH); +} + +static unsigned int axg_spdifin_mode_timer(struct axg_spdifin *priv, + int mode, + unsigned int rate) +{ + /* + * Number of period of the reference clock during a period of the + * input signal reference clock + */ + return rate / (128 * priv->conf->mode_rates[mode]); +} + +static int axg_spdifin_sample_mode_config(struct snd_soc_dai *dai, + struct axg_spdifin *priv) +{ + unsigned int rate, t_next; + int ret, i = SPDIFIN_MODE_NUM - 1; + + /* Set spdif input reference clock */ + ret = clk_set_rate(priv->refclk, priv->conf->ref_rate); + if (ret) { + dev_err(dai->dev, "reference clock rate set failed\n"); + return ret; + } + + /* + * The rate actually set might be slightly different, get + * the actual rate for the following mode calculation + */ + rate = clk_get_rate(priv->refclk); + + /* HW will update mode every 1ms */ + regmap_update_bits(priv->map, SPDIFIN_CTRL1, + SPDIFIN_CTRL1_BASE_TIMER, + FIELD_PREP(SPDIFIN_CTRL1_BASE_TIMER, rate / 1000)); + + /* Threshold based on the minimum width between two edges */ + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_WIDTH_SEL, SPDIFIN_CTRL0_WIDTH_SEL); + + /* Calculate the last timer which has no threshold */ + t_next = axg_spdifin_mode_timer(priv, i, rate); + axg_spdifin_write_timer(priv->map, i, t_next); + + do { + unsigned int t; + + i -= 1; + + /* Calculate the timer */ + t = axg_spdifin_mode_timer(priv, i, rate); + + /* Set the timer value */ + axg_spdifin_write_timer(priv->map, i, t); + + /* Set the threshold value */ + axg_spdifin_write_threshold(priv->map, i, t + t_next); + + /* Save the current timer for the next threshold calculation */ + t_next = t; + + } while (i > 0); + + return 0; +} + +static int axg_spdifin_dai_probe(struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + int ret; + + ret = clk_prepare_enable(priv->pclk); + if (ret) { + dev_err(dai->dev, "failed to enable pclk\n"); + return ret; + } + + ret = axg_spdifin_sample_mode_config(dai, priv); + if (ret) { + dev_err(dai->dev, "mode configuration failed\n"); + clk_disable_unprepare(priv->pclk); + return ret; + } + + return 0; +} + +static int axg_spdifin_dai_remove(struct snd_soc_dai *dai) +{ + struct axg_spdifin *priv = snd_soc_dai_get_drvdata(dai); + + clk_disable_unprepare(priv->pclk); + return 0; +} + +static const struct snd_soc_dai_ops axg_spdifin_ops = { + .prepare = axg_spdifin_prepare, + .startup = axg_spdifin_startup, + .shutdown = axg_spdifin_shutdown, +}; + +static int axg_spdifin_iec958_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958; + uinfo->count = 1; + + return 0; +} + +static int axg_spdifin_get_status_mask(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + int i; + + for (i = 0; i < 24; i++) + ucontrol->value.iec958.status[i] = 0xff; + + return 0; +} + +static int axg_spdifin_get_status(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *c = snd_kcontrol_chip(kcontrol); + struct axg_spdifin *priv = snd_soc_component_get_drvdata(c); + int i, j; + + for (i = 0; i < 6; i++) { + unsigned int val; + + regmap_update_bits(priv->map, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_STATUS_SEL, + FIELD_PREP(SPDIFIN_CTRL0_STATUS_SEL, i)); + + regmap_read(priv->map, SPDIFIN_STAT1, &val); + + for (j = 0; j < 4; j++) { + unsigned int offset = i * 4 + j; + + ucontrol->value.iec958.status[offset] = + (val >> (j * 8)) & 0xff; + } + } + + return 0; +} + +#define AXG_SPDIFIN_IEC958_MASK \ + { \ + .access = SNDRV_CTL_ELEM_ACCESS_READ, \ + .iface = SNDRV_CTL_ELEM_IFACE_PCM, \ + .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, MASK), \ + .info = axg_spdifin_iec958_info, \ + .get = axg_spdifin_get_status_mask, \ + } + +#define AXG_SPDIFIN_IEC958_STATUS \ + { \ + .access = (SNDRV_CTL_ELEM_ACCESS_READ | \ + SNDRV_CTL_ELEM_ACCESS_VOLATILE), \ + .iface = SNDRV_CTL_ELEM_IFACE_PCM, \ + .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, NONE), \ + .info = axg_spdifin_iec958_info, \ + .get = axg_spdifin_get_status, \ + } + +static const char * const spdifin_chsts_src_texts[] = { + "A", "B", +}; + +static SOC_ENUM_SINGLE_DECL(axg_spdifin_chsts_src_enum, SPDIFIN_CTRL0, + SPDIFIN_CTRL0_STATUS_CH_SHIFT, + spdifin_chsts_src_texts); + +static int axg_spdifin_rate_lock_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = 1; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = 192000; + + return 0; +} + +static int axg_spdifin_rate_lock_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *c = snd_kcontrol_chip(kcontrol); + struct axg_spdifin *priv = snd_soc_component_get_drvdata(c); + + ucontrol->value.integer.value[0] = axg_spdifin_get_rate(priv); + + return 0; +} + +#define AXG_SPDIFIN_LOCK_RATE(xname) \ + { \ + .iface = SNDRV_CTL_ELEM_IFACE_PCM, \ + .access = (SNDRV_CTL_ELEM_ACCESS_READ | \ + SNDRV_CTL_ELEM_ACCESS_VOLATILE), \ + .get = axg_spdifin_rate_lock_get, \ + .info = axg_spdifin_rate_lock_info, \ + .name = xname, \ + } + +static const struct snd_kcontrol_new axg_spdifin_controls[] = { + AXG_SPDIFIN_LOCK_RATE("Capture Rate Lock"), + SOC_DOUBLE("Capture Switch", SPDIFIN_CTRL0, 7, 6, 1, 1), + SOC_ENUM(SNDRV_CTL_NAME_IEC958("", CAPTURE, NONE) "Src", + axg_spdifin_chsts_src_enum), + AXG_SPDIFIN_IEC958_MASK, + AXG_SPDIFIN_IEC958_STATUS, +}; + +static const struct snd_soc_component_driver axg_spdifin_component_drv = { + .controls = axg_spdifin_controls, + .num_controls = ARRAY_SIZE(axg_spdifin_controls), +}; + +static const struct regmap_config axg_spdifin_regmap_cfg = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = SPDIFIN_MUTE_VAL, +}; + +static const unsigned int axg_spdifin_mode_rates[SPDIFIN_MODE_NUM] = { + 32000, 44100, 48000, 88200, 96000, 176400, 192000, +}; + +static const struct axg_spdifin_cfg axg_cfg = { + .mode_rates = axg_spdifin_mode_rates, + .ref_rate = 333333333, +}; + +static const struct of_device_id axg_spdifin_of_match[] = { + { + .compatible = "amlogic,axg-spdifin", + .data = &axg_cfg, + }, {} +}; +MODULE_DEVICE_TABLE(of, axg_spdifin_of_match); + +static struct snd_soc_dai_driver * +axg_spdifin_get_dai_drv(struct device *dev, struct axg_spdifin *priv) +{ + struct snd_soc_dai_driver *drv; + int i; + + drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL); + if (!drv) + return ERR_PTR(-ENOMEM); + + drv->name = "SPDIF Input"; + drv->ops = &axg_spdifin_ops; + drv->probe = axg_spdifin_dai_probe; + drv->remove = axg_spdifin_dai_remove; + drv->capture.stream_name = "Capture"; + drv->capture.channels_min = 1; + drv->capture.channels_max = 2; + drv->capture.formats = SNDRV_PCM_FMTBIT_IEC958_SUBFRAME_LE; + + for (i = 0; i < SPDIFIN_MODE_NUM; i++) { + unsigned int rb = + snd_pcm_rate_to_rate_bit(priv->conf->mode_rates[i]); + + if (rb == SNDRV_PCM_RATE_KNOT) + return ERR_PTR(-EINVAL); + + drv->capture.rates |= rb; + } + + return drv; +} + +static int axg_spdifin_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct axg_spdifin *priv; + struct snd_soc_dai_driver *dai_drv; + struct resource *res; + void __iomem *regs; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + platform_set_drvdata(pdev, priv); + + priv->conf = of_device_get_match_data(dev); + if (!priv->conf) { + dev_err(dev, "failed to match device\n"); + return -ENODEV; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + regs = devm_ioremap_resource(dev, res); + if (IS_ERR(regs)) + return PTR_ERR(regs); + + priv->map = devm_regmap_init_mmio(dev, regs, &axg_spdifin_regmap_cfg); + if (IS_ERR(priv->map)) { + dev_err(dev, "failed to init regmap: %ld\n", + PTR_ERR(priv->map)); + return PTR_ERR(priv->map); + } + + priv->pclk = devm_clk_get(dev, "pclk"); + if (IS_ERR(priv->pclk)) { + ret = PTR_ERR(priv->pclk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get pclk: %d\n", ret); + return ret; + } + + priv->refclk = devm_clk_get(dev, "refclk"); + if (IS_ERR(priv->refclk)) { + ret = PTR_ERR(priv->refclk); + if (ret != -EPROBE_DEFER) + dev_err(dev, "failed to get mclk: %d\n", ret); + return ret; + } + + dai_drv = axg_spdifin_get_dai_drv(dev, priv); + if (IS_ERR(dai_drv)) { + dev_err(dev, "failed to get dai driver: %ld\n", + PTR_ERR(dai_drv)); + return PTR_ERR(dai_drv); + } + + return devm_snd_soc_register_component(dev, &axg_spdifin_component_drv, + dai_drv, 1); +} + +static struct platform_driver axg_spdifin_pdrv = { + .probe = axg_spdifin_probe, + .driver = { + .name = "axg-spdifin", + .of_match_table = axg_spdifin_of_match, + }, +}; +module_platform_driver(axg_spdifin_pdrv); + +MODULE_DESCRIPTION("Amlogic AXG SPDIF Input driver"); +MODULE_AUTHOR("Jerome Brunet jbrunet@baylibre.com"); +MODULE_LICENSE("GPL v2");
Add sound/soc/meson drivers entry for Amlogic audio drivers.
Signed-off-by: Jerome Brunet jbrunet@baylibre.com --- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS index 7fe120fc25fa..e8e79713a790 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1310,6 +1310,13 @@ F: drivers/pinctrl/meson/ F: drivers/mmc/host/meson* N: meson
+ARM/Amlogic Meson SoC Sound Drivers +M: Jerome Brunet jbrunet@baylibre.com +L: alsa-devel@alsa-project.org (moderated for non-subscribers) +S: Maintained +F: sound/soc/meson/ +F: Documentation/devicetree/bindings/sound/amlogic* + ARM/Annapurna Labs ALPINE ARCHITECTURE M: Tsahee Zidenberg tsahee@annapurnalabs.com M: Antoine Tenart antoine.tenart@bootlin.com
The patch
MAINTAINERS: Add Amlogic sound drivers entry
has been applied to the asoc tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
From 1b46ed96961db1a826b3e5cadac18c7c4857f054 Mon Sep 17 00:00:00 2001
From: Jerome Brunet jbrunet@baylibre.com Date: Tue, 11 Dec 2018 14:47:13 +0100 Subject: [PATCH] MAINTAINERS: Add Amlogic sound drivers entry
Add sound/soc/meson drivers entry for Amlogic audio drivers.
Signed-off-by: Jerome Brunet jbrunet@baylibre.com Signed-off-by: Mark Brown broonie@kernel.org --- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS index f4855974f325..637f6ce22626 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1309,6 +1309,13 @@ F: drivers/pinctrl/meson/ F: drivers/mmc/host/meson* N: meson
+ARM/Amlogic Meson SoC Sound Drivers +M: Jerome Brunet jbrunet@baylibre.com +L: alsa-devel@alsa-project.org (moderated for non-subscribers) +S: Maintained +F: sound/soc/meson/ +F: Documentation/devicetree/bindings/sound/amlogic* + ARM/Annapurna Labs ALPINE ARCHITECTURE M: Tsahee Zidenberg tsahee@annapurnalabs.com M: Antoine Tenart antoine.tenart@bootlin.com
participants (2)
-
Jerome Brunet -
Mark Brown