Update soundwire bindings with yaml formats.

Signed-off-by: Srinivasa Rao Mandadapu quic_srivasam@quicinc.com Co-developed-by: Ratna Deepthi Kudaravalli quic_rkudarav@quicinc.com Signed-off-by: Ratna Deepthi Kudaravalli quic_rkudarav@quicinc.com --- .../devicetree/bindings/soundwire/qcom,sdw.txt | 214 --------------------- .../devicetree/bindings/soundwire/qcom,sdw.yaml | 185 ++++++++++++++++++ 2 files changed, 185 insertions(+), 214 deletions(-) delete mode 100644 Documentation/devicetree/bindings/soundwire/qcom,sdw.txt create mode 100644 Documentation/devicetree/bindings/soundwire/qcom,sdw.yaml

diff --git a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt deleted file mode 100644 index c85c257..0000000 --- a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt +++ /dev/null @@ -1,214 +0,0 @@ -Qualcomm SoundWire Controller Bindings - - -This binding describes the Qualcomm SoundWire Controller along with its -board specific bus parameters. - -- compatible: - Usage: required - Value type: <stringlist> - Definition: must be "qcom,soundwire-v<MAJOR>.<MINOR>.<STEP>", - Example: - "qcom,soundwire-v1.3.0" - "qcom,soundwire-v1.5.0" - "qcom,soundwire-v1.5.1" - "qcom,soundwire-v1.6.0" -- reg: - Usage: required - Value type: <prop-encoded-array> - Definition: the base address and size of SoundWire controller - address space. - -- interrupts: - Usage: required - Value type: <prop-encoded-array> - Definition: should specify the SoundWire Controller core and optional - wake IRQ - -- interrupt-names: - Usage: Optional - Value type: boolean - Value type: <stringlist> - Definition: should be "core" for core and "wakeup" for wake interrupt. - -- wakeup-source: - Usage: Optional - Value type: boolean - Definition: should specify if SoundWire Controller is wake up capable. - -- clock-names: - Usage: required - Value type: <stringlist> - Definition: should be "iface" for SoundWire Controller interface clock - -- clocks: - Usage: required - Value type: <prop-encoded-array> - Definition: should specify the SoundWire Controller interface clock - -- #sound-dai-cells: - Usage: required - Value type: <u32> - Definition: must be 1 for digital audio interfaces on the controller. - -- qcom,dout-ports: - Usage: required - Value type: <u32> - Definition: must be count of data out ports - -- qcom,din-ports: - Usage: required - Value type: <u32> - Definition: must be count of data in ports - -- qcom,ports-offset1: - Usage: required - Value type: <prop-encoded-array> - Definition: should specify payload transport window offset1 of each - data port. Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-offset2: - Usage: required - Value type: <prop-encoded-array> - Definition: should specify payload transport window offset2 of each - data port. Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-sinterval-low: - Usage: required - Value type: <prop-encoded-array> - Definition: should be sample interval low of each data port. - Out ports followed by In ports. Used for Sample Interval - calculation. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-word-length: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be size of payload channel sample. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-block-pack-mode: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be 0 or 1 to indicate the block packing mode. - 0 to indicate Blocks are per Channel - 1 to indicate Blocks are per Port. - Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-block-group-count: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be in range 1 to 4 to indicate how many sample - intervals are combined into a payload. - Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-lane-control: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be in range 0 to 7 to identify which data lane - the data port uses. - Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-hstart: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be number identifying lowerst numbered coloum in - SoundWire Frame, i.e. left edge of the Transport sub-frame - for each port. Values between 0 and 15 are valid. - Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,ports-hstop: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be number identifying highest numbered coloum in - SoundWire Frame, i.e. the right edge of the Transport - sub-frame for each port. Values between 0 and 15 are valid. - Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- qcom,dports-type: - Usage: optional - Value type: <prop-encoded-array> - Definition: should be one of the following types - 0 for reduced port - 1 for simple ports - 2 for full port - Out ports followed by In ports. - Value of 0xFF indicates that this option is not implemented - or applicable for the respective data port. - More info in MIPI Alliance SoundWire 1.0 Specifications. - -- reset: - Usage: optional - Value type: <prop-encoded-array> - Definition: Should specify the SoundWire audio CSR reset controller interface, - which is required for SoundWire version 1.6.0 and above. - -- reset-names: - Usage: optional - Value type: <stringlist> - Definition: should be "swr_audio_cgcr" for SoundWire audio CSR reset - controller interface. - -Note: - More Information on detail of encoding of these fields can be -found in MIPI Alliance SoundWire 1.0 Specifications. - -= SoundWire devices -Each subnode of the bus represents SoundWire device attached to it. -The properties of these nodes are defined by the individual bindings. - -= EXAMPLE -The following example represents a SoundWire controller on DB845c board -which has controller integrated inside WCD934x codec on SDM845 SoC. - -soundwire: soundwire@c85 { - compatible = "qcom,soundwire-v1.3.0"; - reg = <0xc85 0x20>; - interrupts = <20 IRQ_TYPE_EDGE_RISING>; - clocks = <&wcc>; - clock-names = "iface"; - resets = <&lpass_audiocc LPASS_AUDIO_SWR_TX_CGCR>; - reset-names = "swr_audio_cgcr"; - #sound-dai-cells = <1>; - qcom,dports-type = <0>; - qcom,dout-ports = <6>; - qcom,din-ports = <2>; - qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1F 0x3F 0x7 0x1F 0x3F 0x0F 0x0F>; - qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0C 0x6 0x12 0x0D 0x07 0x0A >; - qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x1F 0x00 0x00 0x1F 0x00 0x00>; - - /* Left Speaker */ - left{ - .... - }; - - /* Right Speaker */ - right{ - .... - }; -}; diff --git a/Documentation/devicetree/bindings/soundwire/qcom,sdw.yaml b/Documentation/devicetree/bindings/soundwire/qcom,sdw.yaml new file mode 100644 index 0000000..bf8f6c1 --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/qcom,sdw.yaml @@ -0,0 +1,185 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soundwire/qcom,sdw.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SoundWire Controller + +maintainers: + - Srinivas Kandagatla srinivas.kandagatla@linaro.org + - Srinivasa Rao Mandadapu quic_srivasam@quicinc.com + +description: + This binding describes the Qualcomm SoundWire controller along with its + board specific bus parameters. + +properties: + compatible: + enum: + - qcom,soundwire-v1.3.0 + - qcom,soundwire-v1.5.0 + - qcom,soundwire-v1.5.1 + - qcom,soundwire-v1.6.0 + + reg: + items: + - description: the base address and size of SoundWire controller + address space. + + interrupts: + items: + - description: specify the SoundWire controller core and optional + wake IRQ. + + interrupt-names: + items: + - const: wakeup + + clocks: + items: + - description: iface clock + + clock-names: + items: + - const: iface + + resets: + items: + - description: SWR_AUDIO_CGCR RESET + + reset-names: + items: + - const: swr_audio_cgcr + + '#sound-dai-cells': + const: 1 + + '#address-cells': + const: 2 + + '#size-cells': + const: 0 + + qcom,din-ports: + $ref: /schemas/types.yaml#/definitions/uint32 + description: count of data in ports + + qcom,dout-ports: + $ref: /schemas/types.yaml#/definitions/uint32 + description: count of data out ports + + qcom,ports-word-length: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: size of payload channel sample. + minItems: 5 + maxItems: 5 + + qcom,ports-sinterval-low: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: sample interval low of each data port. + minItems: 5 + maxItems: 5 + + qcom,ports-offset1: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: payload transport window offset1 of each data port. + minItems: 5 + maxItems: 5 + + qcom,ports-offset2: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: payload transport window offset2 of each data port. + minItems: 5 + maxItems: 5 + + qcom,ports-lane-control: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: identify which data lane the data port uses. + minItems: 5 + maxItems: 5 + + qcom,ports-block-pack-mode: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: indicate the block packing mode. + minItems: 5 + maxItems: 5 + + qcom,ports-hstart: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: identifying lowerst numbered coloum in SoundWire frame. + minItems: 5 + maxItems: 5 + + qcom,ports-hstop: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: identifying highest numbered coloum in SoundWire frame. + minItems: 5 + maxItems: 5 + + qcom,ports-block-group-count: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: indicate how many sample intervals are combined into a payload. + minItems: 5 + maxItems: 5 + +required: + - reg + - interrupts + - interrupt-names + - clocks + - clock-names + - resets + - reset-names + - '#sound-dai-cells' + - '#address-cells' + - '#size-cells' + - qcom,dout-ports + - qcom,din-ports + - qcom,ports-word-length + - qcom,ports-sinterval-low + - qcom,ports-offset1 + - qcom,ports-offset2 + - qcom,ports-lane-control + - qcom,ports-block-pack-mode + - qcom,ports-hstart + - qcom,ports-block-group-count + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/clock/qcom,lpassaudiocc-sc7280.h> + + soundwire@3210000 { + compatible = "qcom,soundwire-v1.6.0"; + reg = <0x03210000 0x2000>; + + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&lpass_rx_macro>; + clock-names = "iface"; + + qcom,din-ports = <0>; + qcom,dout-ports = <5>; + + resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>; + reset-names = "swr_audio_cgcr"; + + qcom,ports-word-length = /bits/ 8 <0x01 0x07 0x04 0xff 0xff>; + qcom,ports-sinterval-low = /bits/ 8 <0x03 0x3f 0x1f 0x03 0x03>; + qcom,ports-offset1 = /bits/ 8 <0x00 0x00 0x0b 0x01 0x01>; + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x0b 0x00 0x00>; + qcom,ports-lane-control = /bits/ 8 <0x01 0x00 0x00 0x00 0x00>; + qcom,ports-block-pack-mode = /bits/ 8 <0xff 0x00 0x01 0xff 0xff>; + qcom,ports-hstart = /bits/ 8 <0xff 0x03 0xff 0xff 0xff>; + qcom,ports-hstop = /bits/ 8 <0xff 0x06 0xff 0xff 0xff>; + qcom,ports-block-group-count = /bits/ 8 <0xff 0xff 0xff 0xff 0x00>; + + #sound-dai-cells = <1>; + #address-cells = <2>; + #size-cells = <0>; + + status = "disabled"; + };