[alsa-devel] [PATCH] ASoC: at91sam9g20ek: Automatically disconnect non-connected pins
According to the schematics the both LHPOUT and RHPOUT are connected to the external connector. RHPOUT is missing from the DAPM routes, but otherwise they seem to be complete.
This patch adds the missing route and then sets the fully_routed flag for the card. This allows to remove all the manual calls to snd_soc_dapm_nc_pin().
Signed-off-by: Lars-Peter Clausen lars@metafoo.de --- sound/soc/atmel/sam9g20_wm8731.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-)
diff --git a/sound/soc/atmel/sam9g20_wm8731.c b/sound/soc/atmel/sam9g20_wm8731.c index 8de8361..d7469cd 100644 --- a/sound/soc/atmel/sam9g20_wm8731.c +++ b/sound/soc/atmel/sam9g20_wm8731.c @@ -95,8 +95,9 @@ static const struct snd_soc_dapm_widget at91sam9g20ek_dapm_widgets[] = {
static const struct snd_soc_dapm_route intercon[] = {
- /* speaker connected to LHPOUT */ + /* speaker connected to LHPOUT/RHPOUT */ {"Ext Spk", NULL, "LHPOUT"}, + {"Ext Spk", NULL, "RHPOUT"},
/* mic is connected to Mic Jack, with WM8731 Mic Bias */ {"MICIN", NULL, "Mic Bias"}, @@ -108,9 +109,7 @@ static const struct snd_soc_dapm_route intercon[] = { */ static int at91sam9g20ek_wm8731_init(struct snd_soc_pcm_runtime *rtd) { - struct snd_soc_codec *codec = rtd->codec; struct snd_soc_dai *codec_dai = rtd->codec_dai; - struct snd_soc_dapm_context *dapm = &codec->dapm; int ret;
printk(KERN_DEBUG @@ -124,10 +123,6 @@ static int at91sam9g20ek_wm8731_init(struct snd_soc_pcm_runtime *rtd) return ret; }
- /* not connected */ - snd_soc_dapm_nc_pin(dapm, "RLINEIN"); - snd_soc_dapm_nc_pin(dapm, "LLINEIN"); - #ifndef ENABLE_MIC_INPUT snd_soc_dapm_nc_pin(&rtd->card->dapm, "Int Mic"); #endif @@ -158,6 +153,7 @@ static struct snd_soc_card snd_soc_at91sam9g20ek = { .num_dapm_widgets = ARRAY_SIZE(at91sam9g20ek_dapm_widgets), .dapm_routes = intercon, .num_dapm_routes = ARRAY_SIZE(intercon), + .fully_routed = true, };
static int at91sam9g20ek_audio_probe(struct platform_device *pdev)
Le 11/04/2015 11:18, Lars-Peter Clausen a écrit :
According to the schematics the both LHPOUT and RHPOUT are connected to the external connector. RHPOUT is missing from the DAPM routes, but otherwise they seem to be complete.
This patch adds the missing route and then sets the fully_routed flag for the card. This allows to remove all the manual calls to snd_soc_dapm_nc_pin().
I don't understand: on the schematics, both the "RLINEIN" and "LLINEIN" are actually not connected. So, why remove these calls to snd_soc_dapm_nc_pin(). Note also that "ROUT" and "LOUT" signals are not connected as well.
But note that I don't know precisely ASoC either...
Bye,
Signed-off-by: Lars-Peter Clausen lars@metafoo.de
sound/soc/atmel/sam9g20_wm8731.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-)
diff --git a/sound/soc/atmel/sam9g20_wm8731.c b/sound/soc/atmel/sam9g20_wm8731.c index 8de8361..d7469cd 100644 --- a/sound/soc/atmel/sam9g20_wm8731.c +++ b/sound/soc/atmel/sam9g20_wm8731.c @@ -95,8 +95,9 @@ static const struct snd_soc_dapm_widget at91sam9g20ek_dapm_widgets[] = {
static const struct snd_soc_dapm_route intercon[] = {
- /* speaker connected to LHPOUT */
/* speaker connected to LHPOUT/RHPOUT */ {"Ext Spk", NULL, "LHPOUT"},
{"Ext Spk", NULL, "RHPOUT"},
/* mic is connected to Mic Jack, with WM8731 Mic Bias */ {"MICIN", NULL, "Mic Bias"},
@@ -108,9 +109,7 @@ static const struct snd_soc_dapm_route intercon[] = { */ static int at91sam9g20ek_wm8731_init(struct snd_soc_pcm_runtime *rtd) {
struct snd_soc_codec *codec = rtd->codec; struct snd_soc_dai *codec_dai = rtd->codec_dai;
struct snd_soc_dapm_context *dapm = &codec->dapm; int ret;
printk(KERN_DEBUG
@@ -124,10 +123,6 @@ static int at91sam9g20ek_wm8731_init(struct snd_soc_pcm_runtime *rtd) return ret; }
- /* not connected */
- snd_soc_dapm_nc_pin(dapm, "RLINEIN");
- snd_soc_dapm_nc_pin(dapm, "LLINEIN");
#ifndef ENABLE_MIC_INPUT snd_soc_dapm_nc_pin(&rtd->card->dapm, "Int Mic"); #endif @@ -158,6 +153,7 @@ static struct snd_soc_card snd_soc_at91sam9g20ek = { .num_dapm_widgets = ARRAY_SIZE(at91sam9g20ek_dapm_widgets), .dapm_routes = intercon, .num_dapm_routes = ARRAY_SIZE(intercon),
- .fully_routed = true,
};
static int at91sam9g20ek_audio_probe(struct platform_device *pdev)
On 04/13/2015 10:53 AM, Nicolas Ferre wrote:
Le 11/04/2015 11:18, Lars-Peter Clausen a écrit :
According to the schematics the both LHPOUT and RHPOUT are connected to the external connector. RHPOUT is missing from the DAPM routes, but otherwise they seem to be complete.
This patch adds the missing route and then sets the fully_routed flag for the card. This allows to remove all the manual calls to snd_soc_dapm_nc_pin().
I don't understand: on the schematics, both the "RLINEIN" and "LLINEIN" are actually not connected. So, why remove these calls to snd_soc_dapm_nc_pin(). Note also that "ROUT" and "LOUT" signals are not connected as well.
For legacy reasons by default a INPUT or OUTPUT pin is considered connected unless explicitly marked as non-connected. When the fully_routed flag is set INPUT and OUTPUT pins are considered to be not connected unless explicitly connected. What the patch does is set the fully_routed flag and remove the explicit calls to snd_soc_dapm_nc_pin() since the pins are now considered to be non-connected by default.
- Lars
Le 13/04/2015 11:02, Lars-Peter Clausen a écrit :
On 04/13/2015 10:53 AM, Nicolas Ferre wrote:
Le 11/04/2015 11:18, Lars-Peter Clausen a écrit :
According to the schematics the both LHPOUT and RHPOUT are connected to the external connector. RHPOUT is missing from the DAPM routes, but otherwise they seem to be complete.
This patch adds the missing route and then sets the fully_routed flag for the card. This allows to remove all the manual calls to snd_soc_dapm_nc_pin().
I don't understand: on the schematics, both the "RLINEIN" and "LLINEIN" are actually not connected. So, why remove these calls to snd_soc_dapm_nc_pin(). Note also that "ROUT" and "LOUT" signals are not connected as well.
For legacy reasons by default a INPUT or OUTPUT pin is considered connected unless explicitly marked as non-connected. When the fully_routed flag is set INPUT and OUTPUT pins are considered to be not connected unless explicitly connected. What the patch does is set the fully_routed flag and remove the explicit calls to snd_soc_dapm_nc_pin() since the pins are now considered to be non-connected by default.
Hopefully I warned that I wasn't aware of ASoC ;-) Ok then.
Bye,
Le 11/04/2015 11:18, Lars-Peter Clausen a écrit :
According to the schematics the both LHPOUT and RHPOUT are connected to the external connector. RHPOUT is missing from the DAPM routes, but otherwise they seem to be complete.
This patch adds the missing route and then sets the fully_routed flag for the card. This allows to remove all the manual calls to snd_soc_dapm_nc_pin().
Signed-off-by: Lars-Peter Clausen lars@metafoo.de
It seems good: Acked-by: Nicolas Ferre nicolas.ferre@atmel.com
sound/soc/atmel/sam9g20_wm8731.c | 10 +++------- 1 file changed, 3 insertions(+), 7 deletions(-)
diff --git a/sound/soc/atmel/sam9g20_wm8731.c b/sound/soc/atmel/sam9g20_wm8731.c index 8de8361..d7469cd 100644 --- a/sound/soc/atmel/sam9g20_wm8731.c +++ b/sound/soc/atmel/sam9g20_wm8731.c @@ -95,8 +95,9 @@ static const struct snd_soc_dapm_widget at91sam9g20ek_dapm_widgets[] = {
static const struct snd_soc_dapm_route intercon[] = {
- /* speaker connected to LHPOUT */
/* speaker connected to LHPOUT/RHPOUT */ {"Ext Spk", NULL, "LHPOUT"},
{"Ext Spk", NULL, "RHPOUT"},
/* mic is connected to Mic Jack, with WM8731 Mic Bias */ {"MICIN", NULL, "Mic Bias"},
@@ -108,9 +109,7 @@ static const struct snd_soc_dapm_route intercon[] = { */ static int at91sam9g20ek_wm8731_init(struct snd_soc_pcm_runtime *rtd) {
struct snd_soc_codec *codec = rtd->codec; struct snd_soc_dai *codec_dai = rtd->codec_dai;
struct snd_soc_dapm_context *dapm = &codec->dapm; int ret;
printk(KERN_DEBUG
@@ -124,10 +123,6 @@ static int at91sam9g20ek_wm8731_init(struct snd_soc_pcm_runtime *rtd) return ret; }
- /* not connected */
- snd_soc_dapm_nc_pin(dapm, "RLINEIN");
- snd_soc_dapm_nc_pin(dapm, "LLINEIN");
#ifndef ENABLE_MIC_INPUT snd_soc_dapm_nc_pin(&rtd->card->dapm, "Int Mic"); #endif @@ -158,6 +153,7 @@ static struct snd_soc_card snd_soc_at91sam9g20ek = { .num_dapm_widgets = ARRAY_SIZE(at91sam9g20ek_dapm_widgets), .dapm_routes = intercon, .num_dapm_routes = ARRAY_SIZE(intercon),
- .fully_routed = true,
};
static int at91sam9g20ek_audio_probe(struct platform_device *pdev)
On Sat, Apr 11, 2015 at 11:18:43AM +0200, Lars-Peter Clausen wrote:
According to the schematics the both LHPOUT and RHPOUT are connected to the external connector. RHPOUT is missing from the DAPM routes, but otherwise they seem to be complete.
Applied, thanks.
participants (3)
-
Lars-Peter Clausen -
Mark Brown -
Nicolas Ferre