[alsa-devel] [PATCH] ASoC: sgtl5000: Allow LRCLK pad drive strength to be changed
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength to be changed via device tree.
When running a stress playback loop test on a mx6dl wandboard channel swap can be noticed on about 10% of the times.
While debugging this issue I noticed that when probing the SGTL5000 LRCLK pin with the scope the swap did not happen. After removing the probe the swap started to happen again.
After changing the LRCLK pad drive strength to the maximum value the issue is gone.
Same fix works on a mx6dl Colibri board as well.
Signed-off-by: Fabio Estevam fabio.estevam@nxp.com --- Documentation/devicetree/bindings/sound/sgtl5000.txt | 9 +++++++++ sound/soc/codecs/sgtl5000.c | 19 ++++++++++++++++++- 2 files changed, 27 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 5666da7..7a73a9d 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -26,6 +26,15 @@ Optional properties: If this node is not mentioned or the value is unknown, then the value is set to 1.25V.
+- lrclk-strength: the LRCLK pad strength. Possible values are: +0, 1, 2 and 3 as per the table below: + +VDDIO 1.8V 2.5V 3.3V +0 = Disable +1 = 1.66 mA 2.87 mA 4.02 mA +2 = 3.33 mA 5.74 mA 8.03 mA +3 = 4.99 mA 8.61 mA 12.05 mA + Example:
codec: sgtl5000@0a { diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c index 1589325..5a2702e 100644 --- a/sound/soc/codecs/sgtl5000.c +++ b/sound/soc/codecs/sgtl5000.c @@ -99,6 +99,13 @@ enum sgtl5000_micbias_resistor { SGTL5000_MICBIAS_8K = 8, };
+enum { + I2S_LRCLK_STRENGTH_DISABLE, + I2S_LRCLK_STRENGTH_LOW, + I2S_LRCLK_STRENGTH_MEDIUM, + I2S_LRCLK_STRENGTH_HIGH, +}; + /* sgtl5000 private structure in codec */ struct sgtl5000_priv { int sysclk; /* sysclk rate */ @@ -111,6 +118,7 @@ struct sgtl5000_priv { int revision; u8 micbias_resistor; u8 micbias_voltage; + u8 lrclk_strength; };
/* @@ -1089,6 +1097,7 @@ static int sgtl5000_enable_regulators(struct i2c_client *client) static int sgtl5000_probe(struct snd_soc_codec *codec) { int ret; + u16 reg; struct sgtl5000_priv *sgtl5000 = snd_soc_codec_get_drvdata(codec);
/* power up sgtl5000 */ @@ -1118,7 +1127,8 @@ static int sgtl5000_probe(struct snd_soc_codec *codec) SGTL5000_DAC_MUTE_RIGHT | SGTL5000_DAC_MUTE_LEFT);
- snd_soc_write(codec, SGTL5000_CHIP_PAD_STRENGTH, 0x015f); + reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT | 0x5f); + snd_soc_write(codec, SGTL5000_CHIP_PAD_STRENGTH, reg);
snd_soc_write(codec, SGTL5000_CHIP_ANA_CTRL, SGTL5000_HP_ZCD_EN | @@ -1347,6 +1357,13 @@ static int sgtl5000_i2c_probe(struct i2c_client *client, } }
+ sgtl5000->lrclk_strength = I2S_LRCLK_STRENGTH_LOW; + if (!of_property_read_u32(np, "lrclk-strength", &value)) { + if (value > I2S_LRCLK_STRENGTH_HIGH) + value = I2S_LRCLK_STRENGTH_LOW; + sgtl5000->lrclk_strength = value; + } + /* Ensure sgtl5000 will start with sane register values */ sgtl5000_fill_defaults(client);
On Wed, 2017-04-05 at 11:32 -0300, Fabio Estevam wrote:
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength to be changed via device tree.
When running a stress playback loop test on a mx6dl wandboard channel swap can be noticed on about 10% of the times.
While debugging this issue I noticed that when probing the SGTL5000 LRCLK pin with the scope the swap did not happen. After removing the probe the swap started to happen again.
After changing the LRCLK pad drive strength to the maximum value the issue is gone.
Same fix works on a mx6dl Colibri board as well.
Signed-off-by: Fabio Estevam fabio.estevam@nxp.com
Hi
I could reproduce the channel swap issue on a Colibri iMX6 Dual with a i.MX 6DualLite. Without the patch I see channel swap in about 3% of playback starts. The patch fixes the issue with the following change to the sgtl5000 device-tree node: diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi index e6faa65..80ece03 100644 --- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi +++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi @@ -253,6 +253,7 @@ compatible = "fsl,sgtl5000"; reg = <0x0a>; clocks = <&clks IMX6QDL_CLK_CKO>; + lrclk-strength = <0x3>; VDDA-supply = <®_2p5v>; VDDIO-supply = <®_3p3v>; };
Tested-by: Max Krummenacher <max.krummenacher at toradex.com>
Max
Documentation/devicetree/bindings/sound/sgtl5000.txt | 9 +++++++++ sound/soc/codecs/sgtl5000.c | 19 ++++++++++++++++++- 2 files changed, 27 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 5666da7..7a73a9d 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -26,6 +26,15 @@ Optional properties: If this node is not mentioned or the value is unknown, then the value is set to 1.25V.
+- lrclk-strength: the LRCLK pad strength. Possible values are: +0, 1, 2 and 3 as per the table below:
+VDDIO 1.8V 2.5V 3.3V +0 = Disable +1 = 1.66 mA 2.87 mA 4.02 mA +2 = 3.33 mA 5.74 mA 8.03 mA +3 = 4.99 mA 8.61 mA 12.05 mA
Example:
codec: sgtl5000@0a { diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c index 1589325..5a2702e 100644 --- a/sound/soc/codecs/sgtl5000.c +++ b/sound/soc/codecs/sgtl5000.c @@ -99,6 +99,13 @@ enum sgtl5000_micbias_resistor { SGTL5000_MICBIAS_8K = 8, };
+enum {
- I2S_LRCLK_STRENGTH_DISABLE,
- I2S_LRCLK_STRENGTH_LOW,
- I2S_LRCLK_STRENGTH_MEDIUM,
- I2S_LRCLK_STRENGTH_HIGH,
+};
/* sgtl5000 private structure in codec */ struct sgtl5000_priv { int sysclk; /* sysclk rate */ @@ -111,6 +118,7 @@ struct sgtl5000_priv { int revision; u8 micbias_resistor; u8 micbias_voltage;
- u8 lrclk_strength;
};
/* @@ -1089,6 +1097,7 @@ static int sgtl5000_enable_regulators(struct i2c_client *client) static int sgtl5000_probe(struct snd_soc_codec *codec) { int ret;
u16 reg; struct sgtl5000_priv *sgtl5000 = snd_soc_codec_get_drvdata(codec);
/* power up sgtl5000 */
@@ -1118,7 +1127,8 @@ static int sgtl5000_probe(struct snd_soc_codec *codec) SGTL5000_DAC_MUTE_RIGHT | SGTL5000_DAC_MUTE_LEFT);
- snd_soc_write(codec, SGTL5000_CHIP_PAD_STRENGTH, 0x015f);
reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT | 0x5f);
snd_soc_write(codec, SGTL5000_CHIP_PAD_STRENGTH, reg);
snd_soc_write(codec, SGTL5000_CHIP_ANA_CTRL, SGTL5000_HP_ZCD_EN |
@@ -1347,6 +1357,13 @@ static int sgtl5000_i2c_probe(struct i2c_client *client, } }
- sgtl5000->lrclk_strength = I2S_LRCLK_STRENGTH_LOW;
- if (!of_property_read_u32(np, "lrclk-strength", &value)) {
if (value > I2S_LRCLK_STRENGTH_HIGH)value = I2S_LRCLK_STRENGTH_LOW;sgtl5000->lrclk_strength = value;- }
- /* Ensure sgtl5000 will start with sane register values */ sgtl5000_fill_defaults(client);
The patch
ASoC: sgtl5000: Allow LRCLK pad drive strength to be changed
has been applied to the asoc tree at
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks, Mark
From 570c70a60f53ca737ead4e5966c446bf0d39fac9 Mon Sep 17 00:00:00 2001
From: Fabio Estevam fabio.estevam@nxp.com Date: Wed, 5 Apr 2017 11:32:34 -0300 Subject: [PATCH] ASoC: sgtl5000: Allow LRCLK pad drive strength to be changed
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength to be changed via device tree.
When running a stress playback loop test on a mx6dl wandboard channel swap can be noticed on about 10% of the times.
While debugging this issue I noticed that when probing the SGTL5000 LRCLK pin with the scope the swap did not happen. After removing the probe the swap started to happen again.
After changing the LRCLK pad drive strength to the maximum value the issue is gone.
Same fix works on a mx6dl Colibri board as well.
Signed-off-by: Fabio Estevam fabio.estevam@nxp.com Tested-by: Max Krummenacher max.krummenacher@toradex.com Signed-off-by: Mark Brown broonie@kernel.org --- Documentation/devicetree/bindings/sound/sgtl5000.txt | 9 +++++++++ sound/soc/codecs/sgtl5000.c | 19 ++++++++++++++++++- 2 files changed, 27 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 5666da7b8605..7a73a9d62015 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -26,6 +26,15 @@ Optional properties: If this node is not mentioned or the value is unknown, then the value is set to 1.25V.
+- lrclk-strength: the LRCLK pad strength. Possible values are: +0, 1, 2 and 3 as per the table below: + +VDDIO 1.8V 2.5V 3.3V +0 = Disable +1 = 1.66 mA 2.87 mA 4.02 mA +2 = 3.33 mA 5.74 mA 8.03 mA +3 = 4.99 mA 8.61 mA 12.05 mA + Example:
codec: sgtl5000@0a { diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c index 1589325855bc..5a2702edeb77 100644 --- a/sound/soc/codecs/sgtl5000.c +++ b/sound/soc/codecs/sgtl5000.c @@ -99,6 +99,13 @@ enum sgtl5000_micbias_resistor { SGTL5000_MICBIAS_8K = 8, };
+enum { + I2S_LRCLK_STRENGTH_DISABLE, + I2S_LRCLK_STRENGTH_LOW, + I2S_LRCLK_STRENGTH_MEDIUM, + I2S_LRCLK_STRENGTH_HIGH, +}; + /* sgtl5000 private structure in codec */ struct sgtl5000_priv { int sysclk; /* sysclk rate */ @@ -111,6 +118,7 @@ struct sgtl5000_priv { int revision; u8 micbias_resistor; u8 micbias_voltage; + u8 lrclk_strength; };
/* @@ -1089,6 +1097,7 @@ static int sgtl5000_enable_regulators(struct i2c_client *client) static int sgtl5000_probe(struct snd_soc_codec *codec) { int ret; + u16 reg; struct sgtl5000_priv *sgtl5000 = snd_soc_codec_get_drvdata(codec);
/* power up sgtl5000 */ @@ -1118,7 +1127,8 @@ static int sgtl5000_probe(struct snd_soc_codec *codec) SGTL5000_DAC_MUTE_RIGHT | SGTL5000_DAC_MUTE_LEFT);
- snd_soc_write(codec, SGTL5000_CHIP_PAD_STRENGTH, 0x015f); + reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT | 0x5f); + snd_soc_write(codec, SGTL5000_CHIP_PAD_STRENGTH, reg);
snd_soc_write(codec, SGTL5000_CHIP_ANA_CTRL, SGTL5000_HP_ZCD_EN | @@ -1347,6 +1357,13 @@ static int sgtl5000_i2c_probe(struct i2c_client *client, } }
+ sgtl5000->lrclk_strength = I2S_LRCLK_STRENGTH_LOW; + if (!of_property_read_u32(np, "lrclk-strength", &value)) { + if (value > I2S_LRCLK_STRENGTH_HIGH) + value = I2S_LRCLK_STRENGTH_LOW; + sgtl5000->lrclk_strength = value; + } + /* Ensure sgtl5000 will start with sane register values */ sgtl5000_fill_defaults(client);
participants (3)
-
Fabio Estevam -
Mark Brown -
Max Krummenacher