This script is mentioned at multisound Kconfig and files. As the driver still exists, it probably makes sense to restore it.

Fixes: 727dede0ba8a ("sound: Retire OSS") Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org --- Documentation/sound/cards/multisound.sh | 1137 +++++++++++++++++++++++ 1 file changed, 1137 insertions(+) create mode 100755 Documentation/sound/cards/multisound.sh

diff --git a/Documentation/sound/cards/multisound.sh b/Documentation/sound/cards/multisound.sh new file mode 100755 index 000000000000..7a7a88256dfd --- /dev/null +++ b/Documentation/sound/cards/multisound.sh @@ -0,0 +1,1137 @@ +#! /bin/sh +# +# Turtle Beach MultiSound Driver Notes +# -- Andrew Veliath andrewtv@usa.net +# +# Last update: September 10, 1998 +# Corresponding msnd driver: 0.8.3 +# +# ** This file is a README (top part) and shell archive (bottom part). +# The corresponding archived utility sources can be unpacked by +# running `sh MultiSound' (the utilities are only needed for the +# Pinnacle and Fiji cards). ** +# +# +# -=-=- Getting Firmware -=-=- +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# See the section `Obtaining and Creating Firmware Files' in this +# document for instructions on obtaining the necessary firmware +# files. +# +# +# Supported Features +# ~~~~~~~~~~~~~~~~~~ +# +# Currently, full-duplex digital audio (/dev/dsp only, /dev/audio is +# not currently available) and mixer functionality (/dev/mixer) are +# supported (memory mapped digital audio is not yet supported). +# Digital transfers and monitoring can be done as well if you have +# the digital daughterboard (see the section on using the S/PDIF port +# for more information). +# +# Support for the Turtle Beach MultiSound Hurricane architecture is +# composed of the following modules (these can also operate compiled +# into the kernel): +# +# msnd - MultiSound base (requires soundcore) +# +# msnd_classic - Base audio/mixer support for Classic, Monetery and +# Tahiti cards +# +# msnd_pinnacle - Base audio/mixer support for Pinnacle and Fiji cards +# +# +# Important Notes - Read Before Using +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# The firmware files are not included (may change in future). You +# must obtain these images from Turtle Beach (they are included in +# the MultiSound Development Kits), and place them in /etc/sound for +# example, and give the full paths in the Linux configuration. If +# you are compiling in support for the MultiSound driver rather than +# using it as a module, these firmware files must be accessible +# during kernel compilation. +# +# Please note these files must be binary files, not assembler. See +# the section later in this document for instructions to obtain these +# files. +# +# +# Configuring Card Resources +# ~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# ** This section is very important, as your card may not work at all +# or your machine may crash if you do not do this correctly. ** +# +# * Classic/Monterey/Tahiti +# +# These cards are configured through the driver msnd_classic. You must +# know the io port, then the driver will select the irq and memory resources +# on the card. It is up to you to know if these are free locations or now, +# a conflict can lock the machine up. +# +# * Pinnacle/Fiji +# +# The Pinnacle and Fiji cards have an extra config port, either +# 0x250, 0x260 or 0x270. This port can be disabled to have the card +# configured strictly through PnP, however you lose the ability to +# access the IDE controller and joystick devices on this card when +# using PnP. The included pinnaclecfg program in this shell archive +# can be used to configure the card in non-PnP mode, and in PnP mode +# you can use isapnptools. These are described briefly here. +# +# pinnaclecfg is not required; you can use the msnd_pinnacle module +# to fully configure the card as well. However, pinnaclecfg can be +# used to change the resource values of a particular device after the +# msnd_pinnacle module has been loaded. If you are compiling the +# driver into the kernel, you must set these values during compile +# time, however other peripheral resource values can be changed with +# the pinnaclecfg program after the kernel is loaded. +# +# +# *** PnP mode +# +# Use pnpdump to obtain a sample configuration if you can; I was able +# to obtain one with the command `pnpdump 1 0x203' -- this may vary +# for you (running pnpdump by itself did not work for me). Then, +# edit this file and use isapnp to uncomment and set the card values. +# Use these values when inserting the msnd_pinnacle module. Using +# this method, you can set the resources for the DSP and the Kurzweil +# synth (Pinnacle). Since Linux does not directly support PnP +# devices, you may have difficulty when using the card in PnP mode +# when it the driver is compiled into the kernel. Using non-PnP mode +# is preferable in this case. +# +# Here is an example mypinnacle.conf for isapnp that sets the card to +# io base 0x210, irq 5 and mem 0xd8000, and also sets the Kurzweil +# synth to 0x330 and irq 9 (may need editing for your system): +# +# (READPORT 0x0203) +# (CSN 2) +# (IDENTIFY *) +# +# # DSP +# (CONFIGURE BVJ0440/-1 (LD 0 +# (INT 0 (IRQ 5 (MODE +E))) (IO 0 (BASE 0x0210)) (MEM 0 (BASE 0x0d8000)) +# (ACT Y))) +# +# # Kurzweil Synth (Pinnacle Only) +# (CONFIGURE BVJ0440/-1 (LD 1 +# (IO 0 (BASE 0x0330)) (INT 0 (IRQ 9 (MODE +E))) +# (ACT Y))) +# +# (WAITFORKEY) +# +# +# *** Non-PnP mode +# +# The second way is by running the card in non-PnP mode. This +# actually has some advantages in that you can access some other +# devices on the card, such as the joystick and IDE controller. To +# configure the card, unpack this shell archive and build the +# pinnaclecfg program. Using this program, you can assign the +# resource values to the card's devices, or disable the devices. As +# an alternative to using pinnaclecfg, you can specify many of the +# configuration values when loading the msnd_pinnacle module (or +# during kernel configuration when compiling the driver into the +# kernel). +# +# If you specify cfg=0x250 for the msnd_pinnacle module, it +# automatically configure the card to the given io, irq and memory +# values using that config port (the config port is jumper selectable +# on the card to 0x250, 0x260 or 0x270). +# +# See the `msnd_pinnacle Additional Options' section below for more +# information on these parameters (also, if you compile the driver +# directly into the kernel, these extra parameters can be useful +# here). +# +# +# ** It is very easy to cause problems in your machine if you choose a +# resource value which is incorrect. ** +# +# +# Examples +# ~~~~~~~~ +# +# * MultiSound Classic/Monterey/Tahiti: +# +# modprobe soundcore +# insmod msnd +# insmod msnd_classic io=0x290 irq=7 mem=0xd0000 +# +# * MultiSound Pinnacle in PnP mode: +# +# modprobe soundcore +# insmod msnd +# isapnp mypinnacle.conf +# insmod msnd_pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values +# +# * MultiSound Pinnacle in non-PnP mode (replace 0x250 with your configuration port, +# one of 0x250, 0x260 or 0x270): +# +# insmod soundcore +# insmod msnd +# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 +# +# * To use the MPU-compatible Kurzweil synth on the Pinnacle in PnP +# mode, add the following (assumes you did `isapnp mypinnacle.conf'): +# +# insmod sound +# insmod mpu401 io=0x330 irq=9 <-- match mypinnacle.conf values +# +# * To use the MPU-compatible Kurzweil synth on the Pinnacle in non-PnP +# mode, add the following. Note how we first configure the peripheral's +# resources, _then_ install a Linux driver for it: +# +# insmod sound +# pinnaclecfg 0x250 mpu 0x330 9 +# insmod mpu401 io=0x330 irq=9 +# +# -- OR you can use the following sequence without pinnaclecfg in non-PnP mode: +# +# insmod soundcore +# insmod msnd +# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9 +# insmod sound +# insmod mpu401 io=0x330 irq=9 +# +# * To setup the joystick port on the Pinnacle in non-PnP mode (though +# you have to find the actual Linux joystick driver elsewhere), you +# can use pinnaclecfg: +# +# pinnaclecfg 0x250 joystick 0x200 +# +# -- OR you can configure this using msnd_pinnacle with the following: +# +# insmod soundcore +# insmod msnd +# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200 +# +# +# msnd_classic, msnd_pinnacle Required Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# If the following options are not given, the module will not load. +# Examine the kernel message log for informative error messages. +# WARNING--probing isn't supported so try to make sure you have the +# correct shared memory area, otherwise you may experience problems. +# +# io I/O base of DSP, e.g. io=0x210 +# irq IRQ number, e.g. irq=5 +# mem Shared memory area, e.g. mem=0xd8000 +# +# +# msnd_classic, msnd_pinnacle Additional Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# fifosize The digital audio FIFOs, in kilobytes. If not +# specified, the default will be used. Increasing +# this value will reduce the chance of a FIFO +# underflow at the expense of increasing overall +# latency. For example, fifosize=512 will +# allocate 512kB read and write FIFOs (1MB total). +# While this may reduce dropouts, a heavy machine +# load will undoubtedly starve the FIFO of data +# and you will eventually get dropouts. One +# option is to alter the scheduling priority of +# the playback process, using `nice' or some form +# of POSIX soft real-time scheduling. +# +# calibrate_signal Setting this to one calibrates the ADCs to the +# signal, zero calibrates to the card (defaults +# to zero). +# +# +# msnd_pinnacle Additional Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# digital Specify digital=1 to enable the S/PDIF input +# if you have the digital daughterboard +# adapter. This will enable access to the +# DIGITAL1 input for the soundcard in the mixer. +# Some mixer programs might have trouble setting +# the DIGITAL1 source as an input. If you have +# trouble, you can try the setdigital.c program +# at the bottom of this document. +# +# cfg Non-PnP configuration port for the Pinnacle +# and Fiji (typically 0x250, 0x260 or 0x270, +# depending on the jumper configuration). If +# this option is omitted, then it is assumed +# that the card is in PnP mode, and that the +# specified DSP resource values are already +# configured with PnP (i.e. it won't attempt to +# do any sort of configuration). +# +# When the Pinnacle is in non-PnP mode, you can use the following +# options to configure particular devices. If a full specification +# for a device is not given, then the device is not configured. Note +# that you still must use a Linux driver for any of these devices +# once their resources are setup (such as the Linux joystick driver, +# or the MPU401 driver from OSS for the Kurzweil synth). +# +# mpu_io I/O port of MPU (on-board Kurzweil synth) +# mpu_irq IRQ of MPU (on-board Kurzweil synth) +# ide_io0 First I/O port of IDE controller +# ide_io1 Second I/O port of IDE controller +# ide_irq IRQ IDE controller +# joystick_io I/O port of joystick +# +# +# Obtaining and Creating Firmware Files +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# For the Classic/Tahiti/Monterey +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# Download to /tmp and unzip the following file from Turtle Beach: +# +# ftp://ftp.voyetra.com/pub/tbs/msndcl/msndvkit.zip +# +# When unzipped, unzip the file named MsndFiles.zip. Then copy the +# following firmware files to /etc/sound (note the file renaming): +# +# cp DSPCODE/MSNDINIT.BIN /etc/sound/msndinit.bin +# cp DSPCODE/MSNDPERM.REB /etc/sound/msndperm.bin +# +# When configuring the Linux kernel, specify /etc/sound/msndinit.bin and +# /etc/sound/msndperm.bin for the two firmware files (Linux kernel +# versions older than 2.2 do not ask for firmware paths, and are +# hardcoded to /etc/sound). +# +# If you are compiling the driver into the kernel, these files must +# be accessible during compilation, but will not be needed later. +# The files must remain, however, if the driver is used as a module. +# +# +# For the Pinnacle/Fiji +# ~~~~~~~~~~~~~~~~~~~~~ +# +# Download to /tmp and unzip the following file from Turtle Beach (be +# sure to use the entire URL; some have had trouble navigating to the +# URL): +# +# ftp://ftp.voyetra.com/pub/tbs/pinn/pnddk100.zip +# +# Unpack this shell archive, and run make in the created directory +# (you need a C compiler and flex to build the utilities). This +# should give you the executables conv, pinnaclecfg and setdigital. +# conv is only used temporarily here to create the firmware files, +# while pinnaclecfg is used to configure the Pinnacle or Fiji card in +# non-PnP mode, and setdigital can be used to set the S/PDIF input on +# the mixer (pinnaclecfg and setdigital should be copied to a +# convenient place, possibly run during system initialization). +# +# To generating the firmware files with the `conv' program, we create +# the binary firmware files by doing the following conversion +# (assuming the archive unpacked into a directory named PINNDDK): +# +# ./conv < PINNDDK/dspcode/pndspini.asm > /etc/sound/pndspini.bin +# ./conv < PINNDDK/dspcode/pndsperm.asm > /etc/sound/pndsperm.bin +# +# The conv (and conv.l) program is not needed after conversion and can +# be safely deleted. Then, when configuring the Linux kernel, specify +# /etc/sound/pndspini.bin and /etc/sound/pndsperm.bin for the two +# firmware files (Linux kernel versions older than 2.2 do not ask for +# firmware paths, and are hardcoded to /etc/sound). +# +# If you are compiling the driver into the kernel, these files must +# be accessible during compilation, but will not be needed later. +# The files must remain, however, if the driver is used as a module. +# +# +# Using Digital I/O with the S/PDIF Port +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# +# If you have a Pinnacle or Fiji with the digital daughterboard and +# want to set it as the input source, you can use this program if you +# have trouble trying to do it with a mixer program (be sure to +# insert the module with the digital=1 option, or say Y to the option +# during compiled-in kernel operation). Upon selection of the S/PDIF +# port, you should be able monitor and record from it. +# +# There is something to note about using the S/PDIF port. Digital +# timing is taken from the digital signal, so if a signal is not +# connected to the port and it is selected as recording input, you +# will find PCM playback to be distorted in playback rate. Also, +# attempting to record at a sampling rate other than the DAT rate may +# be problematic (i.e. trying to record at 8000Hz when the DAT signal +# is 44100Hz). If you have a problem with this, set the recording +# input to analog if you need to record at a rate other than that of +# the DAT rate. +# +# +# -- Shell archive attached below, just run `sh MultiSound' to extract. +# Contains Pinnacle/Fiji utilities to convert firmware, configure +# in non-PnP mode, and select the DIGITAL1 input for the mixer. +# +# +#!/bin/sh +# This is a shell archive (produced by GNU sharutils 4.2). +# To extract the files from this archive, save it to some FILE, remove +# everything before the `!/bin/sh' line above, then type `sh FILE'. +# +# Made on 1998-12-04 10:07 EST by andrewtv@ztransform.velsoft.com. +# Source directory was `/home/andrewtv/programming/pinnacle/pinnacle'. +# +# Existing files will *not* be overwritten unless `-c' is specified. +# +# This shar contains: +# length mode name +# ------ ---------- ------------------------------------------ +# 2046 -rw-rw-r-- MultiSound.d/setdigital.c +# 10235 -rw-rw-r-- MultiSound.d/pinnaclecfg.c +# 106 -rw-rw-r-- MultiSound.d/Makefile +# 141 -rw-rw-r-- MultiSound.d/conv.l +# 1472 -rw-rw-r-- MultiSound.d/msndreset.c +# +save_IFS="${IFS}" +IFS="${IFS}:" +gettext_dir=FAILED +locale_dir=FAILED +first_param="$1" +for dir in $PATH +do + if test "$gettext_dir" = FAILED && test -f $dir/gettext \ + && ($dir/gettext --version >/dev/null 2>&1) + then + set `$dir/gettext --version 2>&1` + if test "$3" = GNU + then + gettext_dir=$dir + fi + fi + if test "$locale_dir" = FAILED && test -f $dir/shar \ + && ($dir/shar --print-text-domain-dir >/dev/null 2>&1) + then + locale_dir=`$dir/shar --print-text-domain-dir` + fi +done +IFS="$save_IFS" +if test "$locale_dir" = FAILED || test "$gettext_dir" = FAILED +then + echo=echo +else + TEXTDOMAINDIR=$locale_dir + export TEXTDOMAINDIR + TEXTDOMAIN=sharutils + export TEXTDOMAIN + echo="$gettext_dir/gettext -s" +fi +touch -am 1231235999 $$.touch >/dev/null 2>&1 +if test ! -f 1231235999 && test -f $$.touch; then + shar_touch=touch +else + shar_touch=: + echo + $echo 'WARNING: not restoring timestamps. Consider getting and' + $echo "installing GNU `touch', distributed in GNU File Utilities..." + echo +fi +rm -f 1231235999 $$.touch +# +if mkdir _sh01426; then + $echo 'x -' 'creating lock directory' +else + $echo 'failed to create lock directory' + exit 1 +fi +# ============= MultiSound.d/setdigital.c ============== +if test ! -d 'MultiSound.d'; then + $echo 'x -' 'creating directory' 'MultiSound.d' + mkdir 'MultiSound.d' +fi +if test -f 'MultiSound.d/setdigital.c' && test "$first_param" != -c; then + $echo 'x -' SKIPPING 'MultiSound.d/setdigital.c' '(file already exists)' +else + $echo 'x -' extracting 'MultiSound.d/setdigital.c' '(text)' + sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/setdigital.c' && +/********************************************************************* +X * +X * setdigital.c - sets the DIGITAL1 input for a mixer +X * +X * Copyright (C) 1998 Andrew Veliath +X * +X * This program is free software; you can redistribute it and/or modify +X * it under the terms of the GNU General Public License as published by +X * the Free Software Foundation; either version 2 of the License, or +X * (at your option) any later version. +X * +X * This program is distributed in the hope that it will be useful, +X * but WITHOUT ANY WARRANTY; without even the implied warranty of +X * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +X * GNU General Public License for more details. +X * +X * You should have received a copy of the GNU General Public License +X * along with this program; if not, write to the Free Software +X * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +X * +X ********************************************************************/ +X +#include <stdio.h> +#include <unistd.h> +#include <fcntl.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> +#include <sys/soundcard.h> +X +int main(int argc, char *argv[]) +{ +X int fd; +X unsigned long recmask, recsrc; +X +X if (argc != 2) { +X fprintf(stderr, "usage: setdigital <mixer device>\n"); +X exit(1); +X } +X +X if ((fd = open(argv[1], O_RDWR)) < 0) { +X perror(argv[1]); +X exit(1); +X } +X +X if (ioctl(fd, SOUND_MIXER_READ_RECMASK, &recmask) < 0) { +X fprintf(stderr, "error: ioctl read recording mask failed\n"); +X perror("ioctl"); +X close(fd); +X exit(1); +X } +X +X if (!(recmask & SOUND_MASK_DIGITAL1)) { +X fprintf(stderr, "error: cannot find DIGITAL1 device in mixer\n"); +X close(fd); +X exit(1); +X } +X +X if (ioctl(fd, SOUND_MIXER_READ_RECSRC, &recsrc) < 0) { +X fprintf(stderr, "error: ioctl read recording source failed\n"); +X perror("ioctl"); +X close(fd); +X exit(1); +X } +X +X recsrc |= SOUND_MASK_DIGITAL1; +X +X if (ioctl(fd, SOUND_MIXER_WRITE_RECSRC, &recsrc) < 0) { +X fprintf(stderr, "error: ioctl write recording source failed\n"); +X perror("ioctl"); +X close(fd); +X exit(1); +X } +X +X close(fd); +X +X return 0; +} +SHAR_EOF + $shar_touch -am 1204092598 'MultiSound.d/setdigital.c' && + chmod 0664 'MultiSound.d/setdigital.c' || + $echo 'restore of' 'MultiSound.d/setdigital.c' 'failed' + if ( md5sum --help 2>&1 | grep 'sage: md5sum [' ) >/dev/null 2>&1 \ + && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then + md5sum -c << SHAR_EOF >/dev/null 2>&1 \ + || $echo 'MultiSound.d/setdigital.c:' 'MD5 check failed' +e87217fc3e71288102ba41fd81f71ec4 MultiSound.d/setdigital.c +SHAR_EOF + else + shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/setdigital.c'`" + test 2046 -eq "$shar_count" || + $echo 'MultiSound.d/setdigital.c:' 'original size' '2046,' 'current size' "$shar_count!" + fi +fi +# ============= MultiSound.d/pinnaclecfg.c ============== +if test -f 'MultiSound.d/pinnaclecfg.c' && test "$first_param" != -c; then + $echo 'x -' SKIPPING 'MultiSound.d/pinnaclecfg.c' '(file already exists)' +else + $echo 'x -' extracting 'MultiSound.d/pinnaclecfg.c' '(text)' + sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/pinnaclecfg.c' && +/********************************************************************* +X * +X * pinnaclecfg.c - Pinnacle/Fiji Device Configuration Program +X * +X * This is for NON-PnP mode only. For PnP mode, use isapnptools. +X * +X * This is Linux-specific, and must be run with root permissions. +X * +X * Part of the Turtle Beach MultiSound Sound Card Driver for Linux +X * +X * Copyright (C) 1998 Andrew Veliath +X * +X * This program is free software; you can redistribute it and/or modify +X * it under the terms of the GNU General Public License as published by +X * the Free Software Foundation; either version 2 of the License, or +X * (at your option) any later version. +X * +X * This program is distributed in the hope that it will be useful, +X * but WITHOUT ANY WARRANTY; without even the implied warranty of +X * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +X * GNU General Public License for more details. +X * +X * You should have received a copy of the GNU General Public License +X * along with this program; if not, write to the Free Software +X * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +X * +X ********************************************************************/ +X +#include <stdio.h> +#include <stdlib.h> +#include <string.h> +#include <errno.h> +#include <unistd.h> +#include <asm/io.h> +#include <asm/types.h> +X +#define IREG_LOGDEVICE 0x07 +#define IREG_ACTIVATE 0x30 +#define LD_ACTIVATE 0x01 +#define LD_DISACTIVATE 0x00 +#define IREG_EECONTROL 0x3F +#define IREG_MEMBASEHI 0x40 +#define IREG_MEMBASELO 0x41 +#define IREG_MEMCONTROL 0x42 +#define IREG_MEMRANGEHI 0x43 +#define IREG_MEMRANGELO 0x44 +#define MEMTYPE_8BIT 0x00 +#define MEMTYPE_16BIT 0x02 +#define MEMTYPE_RANGE 0x00 +#define MEMTYPE_HIADDR 0x01 +#define IREG_IO0_BASEHI 0x60 +#define IREG_IO0_BASELO 0x61 +#define IREG_IO1_BASEHI 0x62 +#define IREG_IO1_BASELO 0x63 +#define IREG_IRQ_NUMBER 0x70 +#define IREG_IRQ_TYPE 0x71 +#define IRQTYPE_HIGH 0x02 +#define IRQTYPE_LOW 0x00 +#define IRQTYPE_LEVEL 0x01 +#define IRQTYPE_EDGE 0x00 +X +#define HIBYTE(w) ((BYTE)(((WORD)(w) >> 8) & 0xFF)) +#define LOBYTE(w) ((BYTE)(w)) +#define MAKEWORD(low,hi) ((WORD)(((BYTE)(low))|(((WORD)((BYTE)(hi)))<<8))) +X +typedef __u8 BYTE; +typedef __u16 USHORT; +typedef __u16 WORD; +X +static int config_port = -1; +X +static int msnd_write_cfg(int cfg, int reg, int value) +{ +X outb(reg, cfg); +X outb(value, cfg + 1); +X if (value != inb(cfg + 1)) { +X fprintf(stderr, "error: msnd_write_cfg: I/O error\n"); +X return -EIO; +X } +X return 0; +} +X +static int msnd_read_cfg(int cfg, int reg) +{ +X outb(reg, cfg); +X return inb(cfg + 1); +} +X +static int msnd_write_cfg_io0(int cfg, int num, WORD io) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_IO0_BASEHI, HIBYTE(io))) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_IO0_BASELO, LOBYTE(io))) +X return -EIO; +X return 0; +} +X +static int msnd_read_cfg_io0(int cfg, int num, WORD *io) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X +X *io = MAKEWORD(msnd_read_cfg(cfg, IREG_IO0_BASELO), +X msnd_read_cfg(cfg, IREG_IO0_BASEHI)); +X +X return 0; +} +X +static int msnd_write_cfg_io1(int cfg, int num, WORD io) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_IO1_BASEHI, HIBYTE(io))) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_IO1_BASELO, LOBYTE(io))) +X return -EIO; +X return 0; +} +X +static int msnd_read_cfg_io1(int cfg, int num, WORD *io) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X +X *io = MAKEWORD(msnd_read_cfg(cfg, IREG_IO1_BASELO), +X msnd_read_cfg(cfg, IREG_IO1_BASEHI)); +X +X return 0; +} +X +static int msnd_write_cfg_irq(int cfg, int num, WORD irq) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_IRQ_NUMBER, LOBYTE(irq))) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_IRQ_TYPE, IRQTYPE_EDGE)) +X return -EIO; +X return 0; +} +X +static int msnd_read_cfg_irq(int cfg, int num, WORD *irq) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X +X *irq = msnd_read_cfg(cfg, IREG_IRQ_NUMBER); +X +X return 0; +} +X +static int msnd_write_cfg_mem(int cfg, int num, int mem) +{ +X WORD wmem; +X +X mem >>= 8; +X mem &= 0xfff; +X wmem = (WORD)mem; +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_MEMBASEHI, HIBYTE(wmem))) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_MEMBASELO, LOBYTE(wmem))) +X return -EIO; +X if (wmem && msnd_write_cfg(cfg, IREG_MEMCONTROL, (MEMTYPE_HIADDR | MEMTYPE_16BIT))) +X return -EIO; +X return 0; +} +X +static int msnd_read_cfg_mem(int cfg, int num, int *mem) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X +X *mem = MAKEWORD(msnd_read_cfg(cfg, IREG_MEMBASELO), +X msnd_read_cfg(cfg, IREG_MEMBASEHI)); +X *mem <<= 8; +X +X return 0; +} +X +static int msnd_activate_logical(int cfg, int num) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_write_cfg(cfg, IREG_ACTIVATE, LD_ACTIVATE)) +X return -EIO; +X return 0; +} +X +static int msnd_write_cfg_logical(int cfg, int num, WORD io0, WORD io1, WORD irq, int mem) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_write_cfg_io0(cfg, num, io0)) +X return -EIO; +X if (msnd_write_cfg_io1(cfg, num, io1)) +X return -EIO; +X if (msnd_write_cfg_irq(cfg, num, irq)) +X return -EIO; +X if (msnd_write_cfg_mem(cfg, num, mem)) +X return -EIO; +X if (msnd_activate_logical(cfg, num)) +X return -EIO; +X return 0; +} +X +static int msnd_read_cfg_logical(int cfg, int num, WORD *io0, WORD *io1, WORD *irq, int *mem) +{ +X if (msnd_write_cfg(cfg, IREG_LOGDEVICE, num)) +X return -EIO; +X if (msnd_read_cfg_io0(cfg, num, io0)) +X return -EIO; +X if (msnd_read_cfg_io1(cfg, num, io1)) +X return -EIO; +X if (msnd_read_cfg_irq(cfg, num, irq)) +X return -EIO; +X if (msnd_read_cfg_mem(cfg, num, mem)) +X return -EIO; +X return 0; +} +X +static void usage(void) +{ +X fprintf(stderr, +X "\n" +X "pinnaclecfg 1.0\n" +X "\n" +X "usage: pinnaclecfg <config port> [device config]\n" +X "\n" +X "This is for use with the card in NON-PnP mode only.\n" +X "\n" +X "Available devices (not all available for Fiji):\n" +X "\n" +X " Device Description\n" +X " -------------------------------------------------------------------\n" +X " reset Reset all devices (i.e. disable)\n" +X " show Display current device configurations\n" +X "\n" +X " dsp <io> <irq> <mem> Audio device\n" +X " mpu <io> <irq> Internal Kurzweil synth\n" +X " ide <io0> <io1> <irq> On-board IDE controller\n" +X " joystick <io> Joystick port\n" +X "\n"); +X exit(1); +} +X +static int cfg_reset(void) +{ +X int i; +X +X for (i = 0; i < 4; ++i) +X msnd_write_cfg_logical(config_port, i, 0, 0, 0, 0); +X +X return 0; +} +X +static int cfg_show(void) +{ +X int i; +X int count = 0; +X +X for (i = 0; i < 4; ++i) { +X WORD io0, io1, irq; +X int mem; +X msnd_read_cfg_logical(config_port, i, &io0, &io1, &irq, &mem); +X switch (i) { +X case 0: +X if (io0 || irq || mem) { +X printf("dsp 0x%x %d 0x%x\n", io0, irq, mem); +X ++count; +X } +X break; +X case 1: +X if (io0 || irq) { +X printf("mpu 0x%x %d\n", io0, irq); +X ++count; +X } +X break; +X case 2: +X if (io0 || io1 || irq) { +X printf("ide 0x%x 0x%x %d\n", io0, io1, irq); +X ++count; +X } +X break; +X case 3: +X if (io0) { +X printf("joystick 0x%x\n", io0); +X ++count; +X } +X break; +X } +X } +X +X if (count == 0) +X fprintf(stderr, "no devices configured\n"); +X +X return 0; +} +X +static int cfg_dsp(int argc, char *argv[]) +{ +X int io, irq, mem; +X +X if (argc < 3 || +X sscanf(argv[0], "0x%x", &io) != 1 || +X sscanf(argv[1], "%d", &irq) != 1 || +X sscanf(argv[2], "0x%x", &mem) != 1) +X usage(); +X +X if (!(io == 0x290 || +X io == 0x260 || +X io == 0x250 || +X io == 0x240 || +X io == 0x230 || +X io == 0x220 || +X io == 0x210 || +X io == 0x3e0)) { +X fprintf(stderr, "error: io must be one of " +X "210, 220, 230, 240, 250, 260, 290, or 3E0\n"); +X usage(); +X } +X +X if (!(irq == 5 || +X irq == 7 || +X irq == 9 || +X irq == 10 || +X irq == 11 || +X irq == 12)) { +X fprintf(stderr, "error: irq must be one of " +X "5, 7, 9, 10, 11 or 12\n"); +X usage(); +X } +X +X if (!(mem == 0xb0000 || +X mem == 0xc8000 || +X mem == 0xd0000 || +X mem == 0xd8000 || +X mem == 0xe0000 || +X mem == 0xe8000)) { +X fprintf(stderr, "error: mem must be one of " +X "0xb0000, 0xc8000, 0xd0000, 0xd8000, 0xe0000 or 0xe8000\n"); +X usage(); +X } +X +X return msnd_write_cfg_logical(config_port, 0, io, 0, irq, mem); +} +X +static int cfg_mpu(int argc, char *argv[]) +{ +X int io, irq; +X +X if (argc < 2 || +X sscanf(argv[0], "0x%x", &io) != 1 || +X sscanf(argv[1], "%d", &irq) != 1) +X usage(); +X +X return msnd_write_cfg_logical(config_port, 1, io, 0, irq, 0); +} +X +static int cfg_ide(int argc, char *argv[]) +{ +X int io0, io1, irq; +X +X if (argc < 3 || +X sscanf(argv[0], "0x%x", &io0) != 1 || +X sscanf(argv[0], "0x%x", &io1) != 1 || +X sscanf(argv[1], "%d", &irq) != 1) +X usage(); +X +X return msnd_write_cfg_logical(config_port, 2, io0, io1, irq, 0); +} +X +static int cfg_joystick(int argc, char *argv[]) +{ +X int io; +X +X if (argc < 1 || +X sscanf(argv[0], "0x%x", &io) != 1) +X usage(); +X +X return msnd_write_cfg_logical(config_port, 3, io, 0, 0, 0); +} +X +int main(int argc, char *argv[]) +{ +X char *device; +X int rv = 0; +X +X --argc; ++argv; +X +X if (argc < 2) +X usage(); +X +X sscanf(argv[0], "0x%x", &config_port); +X if (config_port != 0x250 && config_port != 0x260 && config_port != 0x270) { +X fprintf(stderr, "error: <config port> must be 0x250, 0x260 or 0x270\n"); +X exit(1); +X } +X if (ioperm(config_port, 2, 1)) { +X perror("ioperm"); +X fprintf(stderr, "note: pinnaclecfg must be run as root\n"); +X exit(1); +X } +X device = argv[1]; +X +X argc -= 2; argv += 2; +X +X if (strcmp(device, "reset") == 0) +X rv = cfg_reset(); +X else if (strcmp(device, "show") == 0) +X rv = cfg_show(); +X else if (strcmp(device, "dsp") == 0) +X rv = cfg_dsp(argc, argv); +X else if (strcmp(device, "mpu") == 0) +X rv = cfg_mpu(argc, argv); +X else if (strcmp(device, "ide") == 0) +X rv = cfg_ide(argc, argv); +X else if (strcmp(device, "joystick") == 0) +X rv = cfg_joystick(argc, argv); +X else { +X fprintf(stderr, "error: unknown device %s\n", device); +X usage(); +X } +X +X if (rv) +X fprintf(stderr, "error: device configuration failed\n"); +X +X return 0; +} +SHAR_EOF + $shar_touch -am 1204092598 'MultiSound.d/pinnaclecfg.c' && + chmod 0664 'MultiSound.d/pinnaclecfg.c' || + $echo 'restore of' 'MultiSound.d/pinnaclecfg.c' 'failed' + if ( md5sum --help 2>&1 | grep 'sage: md5sum [' ) >/dev/null 2>&1 \ + && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then + md5sum -c << SHAR_EOF >/dev/null 2>&1 \ + || $echo 'MultiSound.d/pinnaclecfg.c:' 'MD5 check failed' +366bdf27f0db767a3c7921d0a6db20fe MultiSound.d/pinnaclecfg.c +SHAR_EOF + else + shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/pinnaclecfg.c'`" + test 10235 -eq "$shar_count" || + $echo 'MultiSound.d/pinnaclecfg.c:' 'original size' '10235,' 'current size' "$shar_count!" + fi +fi +# ============= MultiSound.d/Makefile ============== +if test -f 'MultiSound.d/Makefile' && test "$first_param" != -c; then + $echo 'x -' SKIPPING 'MultiSound.d/Makefile' '(file already exists)' +else + $echo 'x -' extracting 'MultiSound.d/Makefile' '(text)' + sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/Makefile' && +CC = gcc +CFLAGS = -O +PROGS = setdigital msndreset pinnaclecfg conv +X +all: $(PROGS) +X +clean: +X rm -f $(PROGS) +SHAR_EOF + $shar_touch -am 1204092398 'MultiSound.d/Makefile' && + chmod 0664 'MultiSound.d/Makefile' || + $echo 'restore of' 'MultiSound.d/Makefile' 'failed' + if ( md5sum --help 2>&1 | grep 'sage: md5sum [' ) >/dev/null 2>&1 \ + && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then + md5sum -c << SHAR_EOF >/dev/null 2>&1 \ + || $echo 'MultiSound.d/Makefile:' 'MD5 check failed' +76ca8bb44e3882edcf79c97df6c81845 MultiSound.d/Makefile +SHAR_EOF + else + shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/Makefile'`" + test 106 -eq "$shar_count" || + $echo 'MultiSound.d/Makefile:' 'original size' '106,' 'current size' "$shar_count!" + fi +fi +# ============= MultiSound.d/conv.l ============== +if test -f 'MultiSound.d/conv.l' && test "$first_param" != -c; then + $echo 'x -' SKIPPING 'MultiSound.d/conv.l' '(file already exists)' +else + $echo 'x -' extracting 'MultiSound.d/conv.l' '(text)' + sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/conv.l' && +%% +[ \n\t,\r] +;.* +DB +[0-9A-Fa-f]+H { int n; sscanf(yytext, "%xH", &n); printf("%c", n); } +%% +int yywrap() { return 1; } +main() { yylex(); } +SHAR_EOF + $shar_touch -am 0828231798 'MultiSound.d/conv.l' && + chmod 0664 'MultiSound.d/conv.l' || + $echo 'restore of' 'MultiSound.d/conv.l' 'failed' + if ( md5sum --help 2>&1 | grep 'sage: md5sum [' ) >/dev/null 2>&1 \ + && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then + md5sum -c << SHAR_EOF >/dev/null 2>&1 \ + || $echo 'MultiSound.d/conv.l:' 'MD5 check failed' +d2411fc32cd71a00dcdc1f009e858dd2 MultiSound.d/conv.l +SHAR_EOF + else + shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/conv.l'`" + test 141 -eq "$shar_count" || + $echo 'MultiSound.d/conv.l:' 'original size' '141,' 'current size' "$shar_count!" + fi +fi +# ============= MultiSound.d/msndreset.c ============== +if test -f 'MultiSound.d/msndreset.c' && test "$first_param" != -c; then + $echo 'x -' SKIPPING 'MultiSound.d/msndreset.c' '(file already exists)' +else + $echo 'x -' extracting 'MultiSound.d/msndreset.c' '(text)' + sed 's/^X//' << 'SHAR_EOF' > 'MultiSound.d/msndreset.c' && +/********************************************************************* +X * +X * msndreset.c - resets the MultiSound card +X * +X * Copyright (C) 1998 Andrew Veliath +X * +X * This program is free software; you can redistribute it and/or modify +X * it under the terms of the GNU General Public License as published by +X * the Free Software Foundation; either version 2 of the License, or +X * (at your option) any later version. +X * +X * This program is distributed in the hope that it will be useful, +X * but WITHOUT ANY WARRANTY; without even the implied warranty of +X * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +X * GNU General Public License for more details. +X * +X * You should have received a copy of the GNU General Public License +X * along with this program; if not, write to the Free Software +X * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +X * +X ********************************************************************/ +X +#include <stdio.h> +#include <unistd.h> +#include <fcntl.h> +#include <sys/types.h> +#include <sys/stat.h> +#include <sys/ioctl.h> +#include <sys/soundcard.h> +X +int main(int argc, char *argv[]) +{ +X int fd; +X +X if (argc != 2) { +X fprintf(stderr, "usage: msndreset <mixer device>\n"); +X exit(1); +X } +X +X if ((fd = open(argv[1], O_RDWR)) < 0) { +X perror(argv[1]); +X exit(1); +X } +X +X if (ioctl(fd, SOUND_MIXER_PRIVATE1, 0) < 0) { +X fprintf(stderr, "error: msnd ioctl reset failed\n"); +X perror("ioctl"); +X close(fd); +X exit(1); +X } +X +X close(fd); +X +X return 0; +} +SHAR_EOF + $shar_touch -am 1204100698 'MultiSound.d/msndreset.c' && + chmod 0664 'MultiSound.d/msndreset.c' || + $echo 'restore of' 'MultiSound.d/msndreset.c' 'failed' + if ( md5sum --help 2>&1 | grep 'sage: md5sum [' ) >/dev/null 2>&1 \ + && ( md5sum --version 2>&1 | grep -v 'textutils 1.12' ) >/dev/null; then + md5sum -c << SHAR_EOF >/dev/null 2>&1 \ + || $echo 'MultiSound.d/msndreset.c:' 'MD5 check failed' +c52f876521084e8eb25e12e01dcccb8a MultiSound.d/msndreset.c +SHAR_EOF + else + shar_count="`LC_ALL= LC_CTYPE= LANG= wc -c < 'MultiSound.d/msndreset.c'`" + test 1472 -eq "$shar_count" || + $echo 'MultiSound.d/msndreset.c:' 'original size' '1472,' 'current size' "$shar_count!" + fi +fi +rm -fr _sh01426 +exit 0

The modules for the cards described here changed their names. Update accordingly.

Signed-off-by: Mauro Carvalho Chehab mchehab+samsung@kernel.org --- Documentation/sound/cards/multisound.sh | 72 ++++++++++++------------- 1 file changed, 36 insertions(+), 36 deletions(-)

diff --git a/Documentation/sound/cards/multisound.sh b/Documentation/sound/cards/multisound.sh index 0e0cb029421b..a915a1affcde 100755 --- a/Documentation/sound/cards/multisound.sh +++ b/Documentation/sound/cards/multisound.sh @@ -34,12 +34,12 @@ # composed of the following modules (these can also operate compiled # into the kernel): # -# msnd - MultiSound base (requires soundcore) +# snd-msnd-lib - MultiSound base (requires snd) # -# msnd_classic - Base audio/mixer support for Classic, Monetery and -# Tahiti cards +# snd-msnd-classic - Base audio/mixer support for Classic, Monetery and +# Tahiti cards # -# msnd_pinnacle - Base audio/mixer support for Pinnacle and Fiji cards +# snd-msnd-pinnacle - Base audio/mixer support for Pinnacle and Fiji cards # # # Important Notes - Read Before Using @@ -66,7 +66,7 @@ # # * Classic/Monterey/Tahiti # -# These cards are configured through the driver msnd_classic. You must +# These cards are configured through the driver snd-msnd-classic. You must # know the io port, then the driver will select the irq and memory resources # on the card. It is up to you to know if these are free locations or now, # a conflict can lock the machine up. @@ -81,10 +81,10 @@ # can be used to configure the card in non-PnP mode, and in PnP mode # you can use isapnptools. These are described briefly here. # -# pinnaclecfg is not required; you can use the msnd_pinnacle module +# pinnaclecfg is not required; you can use the snd-msnd-pinnacle module # to fully configure the card as well. However, pinnaclecfg can be # used to change the resource values of a particular device after the -# msnd_pinnacle module has been loaded. If you are compiling the +# snd-msnd-pinnacle module has been loaded. If you are compiling the # driver into the kernel, you must set these values during compile # time, however other peripheral resource values can be changed with # the pinnaclecfg program after the kernel is loaded. @@ -96,7 +96,7 @@ # to obtain one with the command `pnpdump 1 0x203' -- this may vary # for you (running pnpdump by itself did not work for me). Then, # edit this file and use isapnp to uncomment and set the card values. -# Use these values when inserting the msnd_pinnacle module. Using +# Use these values when inserting the snd-msnd-pinnacle module. Using # this method, you can set the resources for the DSP and the Kurzweil # synth (Pinnacle). Since Linux does not directly support PnP # devices, you may have difficulty when using the card in PnP mode @@ -133,16 +133,16 @@ # pinnaclecfg program. Using this program, you can assign the # resource values to the card's devices, or disable the devices. As # an alternative to using pinnaclecfg, you can specify many of the -# configuration values when loading the msnd_pinnacle module (or +# configuration values when loading the snd-msnd-pinnacle module (or # during kernel configuration when compiling the driver into the # kernel). # -# If you specify cfg=0x250 for the msnd_pinnacle module, it +# If you specify cfg=0x250 for the snd-msnd-pinnacle module, it # automatically configure the card to the given io, irq and memory # values using that config port (the config port is jumper selectable # on the card to 0x250, 0x260 or 0x270). # -# See the `msnd_pinnacle Additional Options' section below for more +# See the `snd-msnd-pinnacle Additional Options' section below for more # information on these parameters (also, if you compile the driver # directly into the kernel, these extra parameters can be useful # here). @@ -157,44 +157,44 @@ # # * MultiSound Classic/Monterey/Tahiti: # -# modprobe soundcore -# insmod msnd -# insmod msnd_classic io=0x290 irq=7 mem=0xd0000 +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-classic io=0x290 irq=7 mem=0xd0000 # # * MultiSound Pinnacle in PnP mode: # -# modprobe soundcore -# insmod msnd +# modprobe snd +# insmod snd-msnd-lib # isapnp mypinnacle.conf -# insmod msnd_pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values +# insmod snd-msnd-pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values # # * MultiSound Pinnacle in non-PnP mode (replace 0x250 with your configuration port, # one of 0x250, 0x260 or 0x270): # -# insmod soundcore -# insmod msnd -# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 # # * To use the MPU-compatible Kurzweil synth on the Pinnacle in PnP # mode, add the following (assumes you did `isapnp mypinnacle.conf'): # -# insmod sound +# insmod snd # insmod mpu401 io=0x330 irq=9 <-- match mypinnacle.conf values # # * To use the MPU-compatible Kurzweil synth on the Pinnacle in non-PnP # mode, add the following. Note how we first configure the peripheral's # resources, _then_ install a Linux driver for it: # -# insmod sound +# insmod snd # pinnaclecfg 0x250 mpu 0x330 9 # insmod mpu401 io=0x330 irq=9 # # -- OR you can use the following sequence without pinnaclecfg in non-PnP mode: # -# insmod soundcore -# insmod msnd -# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9 -# insmod sound +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9 +# insmod snd # insmod mpu401 io=0x330 irq=9 # # * To setup the joystick port on the Pinnacle in non-PnP mode (though @@ -203,15 +203,15 @@ # # pinnaclecfg 0x250 joystick 0x200 # -# -- OR you can configure this using msnd_pinnacle with the following: +# -- OR you can configure this using snd-msnd-pinnacle with the following: # -# insmod soundcore -# insmod msnd -# insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200 +# modprobe snd +# insmod snd-msnd-lib +# insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200 # # -# msnd_classic, msnd_pinnacle Required Options -# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# snd-msnd-classic, snd-msnd-pinnacle Required Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ # # If the following options are not given, the module will not load. # Examine the kernel message log for informative error messages. @@ -223,8 +223,8 @@ # mem Shared memory area, e.g. mem=0xd8000 # # -# msnd_classic, msnd_pinnacle Additional Options -# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# snd-msnd-classic, snd-msnd-pinnacle Additional Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ # # fifosize The digital audio FIFOs, in kilobytes. If not # specified, the default will be used. Increasing @@ -244,8 +244,8 @@ # to zero). # # -# msnd_pinnacle Additional Options -# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +# snd-msnd-pinnacle Additional Options +# ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ # # digital Specify digital=1 to enable the S/PDIF input # if you have the digital daughterboard