[alsa-devel] [PATCH 1/4] ASoC: wm8804: Add support for hardware reset line
It is best to use the physical reset if it is available. This patch adds support for a GPIO controlled physical reset for the chip. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> --- sound/soc/codecs/wm8804.c | 26 +++++++++++++++++++++----- 1 files changed, 21 insertions(+), 5 deletions(-) diff --git a/sound/soc/codecs/wm8804.c b/sound/soc/codecs/wm8804.c index f44da83..cc168c4 100644 --- a/sound/soc/codecs/wm8804.c +++ b/sound/soc/codecs/wm8804.c @@ -13,6 +13,7 @@ #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/init.h> +#include <linux/gpio/consumer.h> #include <linux/delay.h> #include <linux/pm.h> #include <linux/of_device.h> @@ -61,6 +62,8 @@ struct wm8804_priv { struct regulator_bulk_data supplies[WM8804_NUM_SUPPLIES]; struct notifier_block disable_nb[WM8804_NUM_SUPPLIES]; int mclk_div; + + struct gpio_desc *reset; }; static int txsrc_get(struct snd_kcontrol *kcontrol, @@ -182,7 +185,7 @@ static bool wm8804_volatile(struct device *dev, unsigned int reg) } } -static int wm8804_reset(struct wm8804_priv *wm8804) +static int wm8804_soft_reset(struct wm8804_priv *wm8804) { return regmap_write(wm8804->regmap, WM8804_RST_DEVID1, 0x0); } @@ -586,6 +589,14 @@ int wm8804_probe(struct device *dev, struct regmap *regmap) wm8804->regmap = regmap; + wm8804->reset = devm_gpiod_get_optional(dev, "wlf,reset", + GPIOD_OUT_LOW); + if (IS_ERR(wm8804->reset)) { + ret = PTR_ERR(wm8804->reset); + dev_err(dev, "Failed to get reset line: %d\n", ret); + return ret; + } + for (i = 0; i < ARRAY_SIZE(wm8804->supplies); i++) wm8804->supplies[i].supply = wm8804_supply_names[i]; @@ -620,6 +631,9 @@ int wm8804_probe(struct device *dev, struct regmap *regmap) return ret; } + if (wm8804->reset) + gpiod_set_value_cansleep(wm8804->reset, 1); + ret = regmap_read(regmap, WM8804_RST_DEVID1, &id1); if (ret < 0) { dev_err(dev, "Failed to read device ID: %d\n", ret); @@ -648,10 +662,12 @@ int wm8804_probe(struct device *dev, struct regmap *regmap) } dev_info(dev, "revision %c\n", id1 + 'A'); - ret = wm8804_reset(wm8804); - if (ret < 0) { - dev_err(dev, "Failed to issue reset: %d\n", ret); - goto err_reg_enable; + if (!wm8804->reset) { + ret = wm8804_soft_reset(wm8804); + if (ret < 0) { + dev_err(dev, "Failed to issue reset: %d\n", ret); + goto err_reg_enable; + } } ret = snd_soc_register_codec(dev, &soc_codec_dev_wm8804, -- 1.7.2.5
From: Charles Keepax <ckeepax@gmail.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> --- Documentation/devicetree/bindings/sound/wm8804.txt | 4 ++++ 1 files changed, 4 insertions(+), 0 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/wm8804.txt b/Documentation/devicetree/bindings/sound/wm8804.txt index 10ef076..6fd124b 100644 --- a/Documentation/devicetree/bindings/sound/wm8804.txt +++ b/Documentation/devicetree/bindings/sound/wm8804.txt @@ -13,6 +13,10 @@ Required properties: - PVDD-supply, DVDD-supply : Power supplies for the device, as covered in Documentation/devicetree/bindings/regulator/regulator.txt +Optional properties: + + - wlf,reset-gpio: A GPIO specifier for the GPIO controlling the reset pin + Example: codec: wm8804@1a { -- 1.7.2.5
From: Sapthagiri Baratam <sapthagiri.baratam@incubesol.com> This change converts the driver to use DAPM to control the power for the various blocks on the chip. As part of this change the existing controls "TX Playback Switch" (controlled power for the SPDIF TX block) and "AIF Playback Switch" (controlled power for the AIF block) are both removed, as they are now redundant since the power state of those blocks is controlled automatically by DAPM. There are several benefits of this change, the most important of which is this change adds support for powering down the SPDIF RX block. The RX block will automatically assume control of the PLL on the chip when it is receiving a signal, so leaving this enabled all the time as was currently done in the driver can be problematic. An incoming SPDIF signal that is not being used can completely destroy the clocking for an in use TX signal. But this change ensures that the RX block will only be powered when the user intends to be receiving data, thus avoiding this issue. Additional benefits include the chip being simpler to operate as the power no longer needs to be manually controlled between use-cases and a small power saving (although it is acknowledged that this is likely unimportant in the typical use-cases for this chip). Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@incubesol.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> --- Changes since v1: - Add much more detail in the commit message - Don't rename the 'Input Source' control sound/soc/codecs/wm8804.c | 140 ++++++++++++++++++++++++++------------------ 1 files changed, 83 insertions(+), 57 deletions(-) diff --git a/sound/soc/codecs/wm8804.c b/sound/soc/codecs/wm8804.c index cc168c4..cff34be 100644 --- a/sound/soc/codecs/wm8804.c +++ b/sound/soc/codecs/wm8804.c @@ -25,6 +25,7 @@ #include <sound/soc.h> #include <sound/initval.h> #include <sound/tlv.h> +#include <sound/soc-dapm.h> #include "wm8804.h" @@ -64,14 +65,16 @@ struct wm8804_priv { int mclk_div; struct gpio_desc *reset; -}; -static int txsrc_get(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol); + int aif_pwr; +}; static int txsrc_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol); +static int wm8804_aif_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event); + /* * We can't use the same notifier block for more than one supply and * there's no way I can see to get from a callback to the caller @@ -93,26 +96,62 @@ WM8804_REGULATOR_EVENT(0) WM8804_REGULATOR_EVENT(1) static const char *txsrc_text[] = { "S/PDIF RX", "AIF" }; -static SOC_ENUM_SINGLE_EXT_DECL(txsrc, txsrc_text); +static const SOC_ENUM_SINGLE_DECL(txsrc, WM8804_SPDTX4, 6, txsrc_text); -static const struct snd_kcontrol_new wm8804_snd_controls[] = { - SOC_ENUM_EXT("Input Source", txsrc, txsrc_get, txsrc_put), - SOC_SINGLE("TX Playback Switch", WM8804_PWRDN, 2, 1, 1), - SOC_SINGLE("AIF Playback Switch", WM8804_PWRDN, 4, 1, 1) +static const struct snd_kcontrol_new wm8804_tx_source_mux[] = { + SOC_DAPM_ENUM_EXT("Input Source", txsrc, + snd_soc_dapm_get_enum_double, txsrc_put), }; -static int txsrc_get(struct snd_kcontrol *kcontrol, - struct snd_ctl_elem_value *ucontrol) -{ - struct snd_soc_codec *codec; - unsigned int src; +static const struct snd_soc_dapm_widget wm8804_dapm_widgets[] = { +SND_SOC_DAPM_OUTPUT("SPDIF Out"), +SND_SOC_DAPM_INPUT("SPDIF In"), + +SND_SOC_DAPM_PGA("SPDIFTX", WM8804_PWRDN, 2, 1, NULL, 0), +SND_SOC_DAPM_PGA("SPDIFRX", WM8804_PWRDN, 1, 1, NULL, 0), + +SND_SOC_DAPM_MUX("Tx Source", SND_SOC_NOPM, 6, 0, wm8804_tx_source_mux), + +SND_SOC_DAPM_AIF_OUT_E("AIFTX", NULL, 0, SND_SOC_NOPM, 0, 0, wm8804_aif_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD), +SND_SOC_DAPM_AIF_IN_E("AIFRX", NULL, 0, SND_SOC_NOPM, 0, 0, wm8804_aif_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD), +}; + +static const struct snd_soc_dapm_route wm8804_dapm_routes[] = { + { "AIFRX", NULL, "Playback" }, + { "Tx Source", "AIF", "AIFRX" }, + + { "SPDIFRX", NULL, "SPDIF In" }, + { "Tx Source", "S/PDIF RX", "SPDIFRX" }, + + { "SPDIFTX", NULL, "Tx Source" }, + { "SPDIF Out", NULL, "SPDIFTX" }, - codec = snd_soc_kcontrol_codec(kcontrol); - src = snd_soc_read(codec, WM8804_SPDTX4); - if (src & 0x40) - ucontrol->value.integer.value[0] = 1; - else - ucontrol->value.integer.value[0] = 0; + { "AIFTX", NULL, "SPDIFRX" }, + { "Capture", NULL, "AIFTX" }, +}; + +static int wm8804_aif_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_codec *codec = snd_soc_dapm_to_codec(w->dapm); + struct wm8804_priv *wm8804 = snd_soc_codec_get_drvdata(codec); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + /* power up the aif */ + if (!wm8804->aif_pwr) + snd_soc_update_bits(codec, WM8804_PWRDN, 0x10, 0x0); + wm8804->aif_pwr++; + break; + case SND_SOC_DAPM_POST_PMD: + /* power down only both paths are disabled */ + wm8804->aif_pwr--; + if (!wm8804->aif_pwr) + snd_soc_update_bits(codec, WM8804_PWRDN, 0x10, 0x10); + break; + } return 0; } @@ -120,48 +159,33 @@ static int txsrc_get(struct snd_kcontrol *kcontrol, static int txsrc_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_value *ucontrol) { - struct snd_soc_codec *codec; - unsigned int src, txpwr; + struct snd_soc_codec *codec = snd_soc_dapm_kcontrol_codec(kcontrol); + struct snd_soc_dapm_context *dapm = &codec->dapm; + struct soc_enum *e = (struct soc_enum *)kcontrol->private_value; + unsigned int val = ucontrol->value.enumerated.item[0] << e->shift_l; + unsigned int mask = 1 << e->shift_l; + unsigned int txpwr; + + if (val != 0 && val != mask) + return -EINVAL; - codec = snd_soc_kcontrol_codec(kcontrol); + snd_soc_dapm_mutex_lock(dapm); - if (ucontrol->value.integer.value[0] != 0 - && ucontrol->value.integer.value[0] != 1) - return -EINVAL; + if (snd_soc_test_bits(codec, e->reg, mask, val)) { + /* save the current power state of the transmitter */ + txpwr = snd_soc_read(codec, WM8804_PWRDN) & 0x4; - src = snd_soc_read(codec, WM8804_SPDTX4); - switch ((src & 0x40) >> 6) { - case 0: - if (!ucontrol->value.integer.value[0]) - return 0; - break; - case 1: - if (ucontrol->value.integer.value[1]) - return 0; - break; - } + /* power down the transmitter */ + snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x4); - /* save the current power state of the transmitter */ - txpwr = snd_soc_read(codec, WM8804_PWRDN) & 0x4; - /* power down the transmitter */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, 0x4); - /* set the tx source */ - snd_soc_update_bits(codec, WM8804_SPDTX4, 0x40, - ucontrol->value.integer.value[0] << 6); - - if (ucontrol->value.integer.value[0]) { - /* power down the receiver */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x2, 0x2); - /* power up the AIF */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x10, 0); - } else { - /* don't power down the AIF -- may be used as an output */ - /* power up the receiver */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x2, 0); + /* set the tx source */ + snd_soc_update_bits(codec, e->reg, mask, val); + + /* restore the transmitter's configuration */ + snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, txpwr); } - /* restore the transmitter's configuration */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x4, txpwr); + snd_soc_dapm_mutex_unlock(dapm); return 0; } @@ -558,8 +582,10 @@ static const struct snd_soc_codec_driver soc_codec_dev_wm8804 = { .set_bias_level = wm8804_set_bias_level, .idle_bias_off = true, - .controls = wm8804_snd_controls, - .num_controls = ARRAY_SIZE(wm8804_snd_controls), + .dapm_widgets = wm8804_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(wm8804_dapm_widgets), + .dapm_routes = wm8804_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(wm8804_dapm_routes), }; const struct regmap_config wm8804_regmap_config = { -- 1.7.2.5
From: Charles Keepax <ckeepax@gmail.com> Currently both the oscillator and the PLL are powered up in set_bias_level. This can be problematic when using output clocks from the wm8804 for other devices. The snd_soc_codec_set_pll API defines that a clock should be available once the call returns, however, with all the clocking controlled in set_bias_level this is not currently the case. This patch enables pm_runtime for the wm8804, enabling both the regulators and the oscillator when the chip resumes, and enabling the PLL in the snd_soc_codec_set_pll call. Naturally the enabling the PLL will also cause the chip to resume. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> --- sound/soc/codecs/wm8804-i2c.c | 1 + sound/soc/codecs/wm8804-spi.c | 1 + sound/soc/codecs/wm8804.c | 109 ++++++++++++++++++++++------------------- sound/soc/codecs/wm8804.h | 1 + 4 files changed, 62 insertions(+), 50 deletions(-) diff --git a/sound/soc/codecs/wm8804-i2c.c b/sound/soc/codecs/wm8804-i2c.c index 5bd4af2..6596f5f 100644 --- a/sound/soc/codecs/wm8804-i2c.c +++ b/sound/soc/codecs/wm8804-i2c.c @@ -50,6 +50,7 @@ static struct i2c_driver wm8804_i2c_driver = { .driver = { .name = "wm8804", .owner = THIS_MODULE, + .pm = &wm8804_pm, .of_match_table = wm8804_of_match, }, .probe = wm8804_i2c_probe, diff --git a/sound/soc/codecs/wm8804-spi.c b/sound/soc/codecs/wm8804-spi.c index 287e11e..407a3cf 100644 --- a/sound/soc/codecs/wm8804-spi.c +++ b/sound/soc/codecs/wm8804-spi.c @@ -43,6 +43,7 @@ static struct spi_driver wm8804_spi_driver = { .driver = { .name = "wm8804", .owner = THIS_MODULE, + .pm = &wm8804_pm, .of_match_table = wm8804_of_match, }, .probe = wm8804_spi_probe, diff --git a/sound/soc/codecs/wm8804.c b/sound/soc/codecs/wm8804.c index cff34be..1e403f6 100644 --- a/sound/soc/codecs/wm8804.c +++ b/sound/soc/codecs/wm8804.c @@ -16,6 +16,7 @@ #include <linux/gpio/consumer.h> #include <linux/delay.h> #include <linux/pm.h> +#include <linux/pm_runtime.h> #include <linux/of_device.h> #include <linux/regulator/consumer.h> #include <linux/slab.h> @@ -59,6 +60,7 @@ static const struct reg_default wm8804_reg_defaults[] = { }; struct wm8804_priv { + struct device *dev; struct regmap *regmap; struct regulator_bulk_data supplies[WM8804_NUM_SUPPLIES]; struct notifier_block disable_nb[WM8804_NUM_SUPPLIES]; @@ -403,19 +405,19 @@ static int wm8804_set_pll(struct snd_soc_dai *dai, int pll_id, int source, unsigned int freq_in, unsigned int freq_out) { - struct snd_soc_codec *codec; + struct snd_soc_codec *codec = dai->codec; + struct wm8804_priv *wm8804 = snd_soc_codec_get_drvdata(codec); + bool change; - codec = dai->codec; if (!freq_in || !freq_out) { /* disable the PLL */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x1, 0x1); - return 0; + regmap_update_bits_check(wm8804->regmap, WM8804_PWRDN, + 0x1, 0x1, &change); + if (change) + pm_runtime_put(wm8804->dev); } else { int ret; struct pll_div pll_div; - struct wm8804_priv *wm8804; - - wm8804 = snd_soc_codec_get_drvdata(codec); ret = pll_factors(&pll_div, freq_out, freq_in, wm8804->mclk_div); @@ -423,7 +425,10 @@ static int wm8804_set_pll(struct snd_soc_dai *dai, int pll_id, return ret; /* power down the PLL before reprogramming it */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x1, 0x1); + regmap_update_bits_check(wm8804->regmap, WM8804_PWRDN, + 0x1, 0x1, &change); + if (!change) + pm_runtime_get_sync(wm8804->dev); /* set PLLN and PRESCALE */ snd_soc_update_bits(codec, WM8804_PLL4, 0xf | 0x10, @@ -501,47 +506,6 @@ static int wm8804_set_clkdiv(struct snd_soc_dai *dai, return 0; } -static int wm8804_set_bias_level(struct snd_soc_codec *codec, - enum snd_soc_bias_level level) -{ - int ret; - struct wm8804_priv *wm8804; - - wm8804 = snd_soc_codec_get_drvdata(codec); - switch (level) { - case SND_SOC_BIAS_ON: - break; - case SND_SOC_BIAS_PREPARE: - /* power up the OSC and the PLL */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0); - break; - case SND_SOC_BIAS_STANDBY: - if (codec->dapm.bias_level == SND_SOC_BIAS_OFF) { - ret = regulator_bulk_enable(ARRAY_SIZE(wm8804->supplies), - wm8804->supplies); - if (ret) { - dev_err(codec->dev, - "Failed to enable supplies: %d\n", - ret); - return ret; - } - regcache_sync(wm8804->regmap); - } - /* power down the OSC and the PLL */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0x9); - break; - case SND_SOC_BIAS_OFF: - /* power down the OSC and the PLL */ - snd_soc_update_bits(codec, WM8804_PWRDN, 0x9, 0x9); - regulator_bulk_disable(ARRAY_SIZE(wm8804->supplies), - wm8804->supplies); - break; - } - - codec->dapm.bias_level = level; - return 0; -} - static const struct snd_soc_dai_ops wm8804_dai_ops = { .hw_params = wm8804_hw_params, .set_fmt = wm8804_set_fmt, @@ -579,7 +543,6 @@ static struct snd_soc_dai_driver wm8804_dai = { }; static const struct snd_soc_codec_driver soc_codec_dev_wm8804 = { - .set_bias_level = wm8804_set_bias_level, .idle_bias_off = true, .dapm_widgets = wm8804_dapm_widgets, @@ -613,6 +576,7 @@ int wm8804_probe(struct device *dev, struct regmap *regmap) dev_set_drvdata(dev, wm8804); + wm8804->dev = dev; wm8804->regmap = regmap; wm8804->reset = devm_gpiod_get_optional(dev, "wlf,reset", @@ -703,6 +667,10 @@ int wm8804_probe(struct device *dev, struct regmap *regmap) goto err_reg_enable; } + pm_runtime_set_active(dev); + pm_runtime_enable(dev); + pm_runtime_idle(dev); + return 0; err_reg_enable: @@ -713,10 +681,51 @@ EXPORT_SYMBOL_GPL(wm8804_probe); void wm8804_remove(struct device *dev) { + pm_runtime_disable(dev); snd_soc_unregister_codec(dev); } EXPORT_SYMBOL_GPL(wm8804_remove); +#if IS_ENABLED(CONFIG_PM) +static int wm8804_runtime_resume(struct device *dev) +{ + struct wm8804_priv *wm8804 = dev_get_drvdata(dev); + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(wm8804->supplies), + wm8804->supplies); + if (ret) { + dev_err(wm8804->dev, "Failed to enable supplies: %d\n", ret); + return ret; + } + + regcache_sync(wm8804->regmap); + + /* Power up OSCCLK */ + regmap_update_bits(wm8804->regmap, WM8804_PWRDN, 0x8, 0x0); + + return 0; +} + +static int wm8804_runtime_suspend(struct device *dev) +{ + struct wm8804_priv *wm8804 = dev_get_drvdata(dev); + + /* Power down OSCCLK */ + regmap_update_bits(wm8804->regmap, WM8804_PWRDN, 0x8, 0x8); + + regulator_bulk_disable(ARRAY_SIZE(wm8804->supplies), + wm8804->supplies); + + return 0; +} +#endif + +const struct dev_pm_ops wm8804_pm = { + SET_RUNTIME_PM_OPS(wm8804_runtime_suspend, wm8804_runtime_resume, NULL) +}; +EXPORT_SYMBOL_GPL(wm8804_pm); + MODULE_DESCRIPTION("ASoC WM8804 driver"); MODULE_AUTHOR("Dimitris Papastamos <dp@opensource.wolfsonmicro.com>"); MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/wm8804.h b/sound/soc/codecs/wm8804.h index a39a256..aa72fa6 100644 --- a/sound/soc/codecs/wm8804.h +++ b/sound/soc/codecs/wm8804.h @@ -65,6 +65,7 @@ #define WM8804_MCLKDIV_128FS 1 extern const struct regmap_config wm8804_regmap_config; +extern const struct dev_pm_ops wm8804_pm; int wm8804_probe(struct device *dev, struct regmap *regmap); void wm8804_remove(struct device *dev); -- 1.7.2.5
On Tue, Apr 07, 2015 at 11:33:27AM +0100, Charles Keepax wrote:
It is best to use the physical reset if it is available. This patch adds support for a GPIO controlled physical reset for the chip.
You appear to have just sent me two different versions of this series (possibly, there's some versioning on one patch in the middle?) - what's going on there, what are the differences?
On Tue, Apr 07, 2015 at 11:47:20AM +0100, Mark Brown wrote:
On Tue, Apr 07, 2015 at 11:33:27AM +0100, Charles Keepax wrote:
It is best to use the physical reset if it is available. This patch adds support for a GPIO controlled physical reset for the chip.
You appear to have just sent me two different versions of this series (possibly, there's some versioning on one patch in the middle?) - what's going on there, what are the differences?
Very sorry, I forgot to CC Sapthagiri again on the first round that is the only difference. Thanks, Charles
participants (2)
-
Charles Keepax -
Mark Brown