From: Naveen Manohar naveen.m@intel.com

Machine driver to enable RT5682 on SSP0, DMIC, HDMI and RT1011 AMP on SSP1 with 2 CH / 24 bit TDM Playback over 4 individual codecs and 4 CH / 24 bit Capture to provide feedback.

Changes from V1: adressed minor comments of V1

Signed-off-by: Naveen Manohar naveen.m@intel.com Signed-off-by: Sathya Prakash M R sathya.prakash.m.r@intel.com --- sound/soc/intel/boards/Kconfig | 18 ++ sound/soc/intel/boards/Makefile | 2 + sound/soc/intel/boards/cml_rt1011_rt5682.c | 473 +++++++++++++++++++++++++++++ 3 files changed, 493 insertions(+) create mode 100644 sound/soc/intel/boards/cml_rt1011_rt5682.c

diff --git a/sound/soc/intel/boards/Kconfig b/sound/soc/intel/boards/Kconfig index 50bf149818b5..6c41aa5e78c0 100644 --- a/sound/soc/intel/boards/Kconfig +++ b/sound/soc/intel/boards/Kconfig @@ -382,6 +382,24 @@ config SND_SOC_INTEL_GLK_RT5682_MAX98357A_MACH

endif ## SND_SOC_INTEL_GLK || (SND_SOC_SOF_GEMINILAKE && SND_SOC_SOF_HDA_LINK)

+if SND_SOC_SOF_COMETLAKE_LP && SND_SOC_SOF_HDA_LINK + +config SND_SOC_INTEL_SOF_CML_RT1011_RT5682_MACH + tristate "CML with RT1011 and RT5682 in I2S Mode" + depends on I2C && ACPI + depends on MFD_INTEL_LPSS || COMPILE_TEST + select SND_SOC_RT1011 + select SND_SOC_RT5682 + select SND_SOC_DMIC + select SND_SOC_HDAC_HDMI + help + This adds support for ASoC machine driver for SOF platform with + RT1011 + RT5682 I2S codec. + Say Y if you have such a device. + If unsure select "N". + +endif ## SND_SOC_SOF_COMETLAKE_LP && SND_SOC_SOF_HDA_LINK + if SND_SOC_INTEL_SKYLAKE_HDAUDIO_CODEC || SND_SOC_SOF_HDA_AUDIO_CODEC

config SND_SOC_INTEL_SKL_HDA_DSP_GENERIC_MACH diff --git a/sound/soc/intel/boards/Makefile b/sound/soc/intel/boards/Makefile index 6445f90ea542..848a2684535f 100644 --- a/sound/soc/intel/boards/Makefile +++ b/sound/soc/intel/boards/Makefile @@ -18,6 +18,7 @@ snd-soc-sst-byt-cht-da7213-objs := bytcht_da7213.o snd-soc-sst-byt-cht-es8316-objs := bytcht_es8316.o snd-soc-sst-byt-cht-nocodec-objs := bytcht_nocodec.o snd-soc-sof_rt5682-objs := sof_rt5682.o +snd-soc-cml_rt1011_rt5682-objs := cml_rt1011_rt5682.o snd-soc-kbl_da7219_max98357a-objs := kbl_da7219_max98357a.o snd-soc-kbl_da7219_max98927-objs := kbl_da7219_max98927.o snd-soc-kbl_rt5663_max98927-objs := kbl_rt5663_max98927.o @@ -47,6 +48,7 @@ obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_CX2072X_MACH) += snd-soc-sst-byt-cht-cx2072x. obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_DA7213_MACH) += snd-soc-sst-byt-cht-da7213.o obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_ES8316_MACH) += snd-soc-sst-byt-cht-es8316.o obj-$(CONFIG_SND_SOC_INTEL_BYT_CHT_NOCODEC_MACH) += snd-soc-sst-byt-cht-nocodec.o +obj-$(CONFIG_SND_SOC_INTEL_SOF_CML_RT1011_RT5682_MACH) += cml_rt1011_rt5682.o obj-$(CONFIG_SND_SOC_INTEL_KBL_DA7219_MAX98357A_MACH) += snd-soc-kbl_da7219_max98357a.o obj-$(CONFIG_SND_SOC_INTEL_KBL_DA7219_MAX98927_MACH) += snd-soc-kbl_da7219_max98927.o obj-$(CONFIG_SND_SOC_INTEL_KBL_RT5663_MAX98927_MACH) += snd-soc-kbl_rt5663_max98927.o diff --git a/sound/soc/intel/boards/cml_rt1011_rt5682.c b/sound/soc/intel/boards/cml_rt1011_rt5682.c new file mode 100644 index 000000000000..1e257daea488 --- /dev/null +++ b/sound/soc/intel/boards/cml_rt1011_rt5682.c @@ -0,0 +1,473 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright(c) 2019 Intel Corporation. + +/* + * Intel Cometlake I2S Machine driver for RT1011 + RT5682 codec + */ + +#include <linux/input.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/dmi.h> +#include <linux/slab.h> +#include <asm/cpu_device_id.h> +#include <linux/acpi.h> +#include <sound/core.h> +#include <sound/jack.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/rt5682.h> +#include <sound/soc-acpi.h> +#include "../../codecs/rt1011.h" +#include "../../codecs/rt5682.h" +#include "../../codecs/hdac_hdmi.h" + +/* The platform clock outputs 24Mhz clock to codec as I2S MCLK */ +#define CML_PLAT_CLK 24000000 +#define CML_RT1011_CODEC_DAI "rt1011-aif" +#define CML_RT5682_CODEC_DAI "rt5682-aif1" +#define NAME_SIZE 32 + +static struct snd_soc_jack hdmi_jack[3]; + +struct hdmi_pcm { + struct list_head head; + struct snd_soc_dai *codec_dai; + int device; +}; + +struct card_private { + char codec_name[SND_ACPI_I2C_ID_LEN]; + struct snd_soc_jack headset; + struct list_head hdmi_pcm_list; +}; + +static const struct snd_kcontrol_new cml_controls[] = { + SOC_DAPM_PIN_SWITCH("Headphone Jack"), + SOC_DAPM_PIN_SWITCH("Headset Mic"), + SOC_DAPM_PIN_SWITCH("TL Ext Spk"), + SOC_DAPM_PIN_SWITCH("TR Ext Spk"), + SOC_DAPM_PIN_SWITCH("WL Ext Spk"), + SOC_DAPM_PIN_SWITCH("WR Ext Spk"), +}; + +static const struct snd_soc_dapm_widget cml_rt1011_rt5682_widgets[] = { + SND_SOC_DAPM_SPK("TL Ext Spk", NULL), + SND_SOC_DAPM_SPK("TR Ext Spk", NULL), + SND_SOC_DAPM_SPK("WL Ext Spk", NULL), + SND_SOC_DAPM_SPK("WR Ext Spk", NULL), + SND_SOC_DAPM_HP("Headphone Jack", NULL), + SND_SOC_DAPM_MIC("Headset Mic", NULL), + SND_SOC_DAPM_MIC("SoC DMIC", NULL), +}; + +static const struct snd_soc_dapm_route cml_rt1011_rt5682_map[] = { + /*speaker*/ + { "TL Ext Spk", NULL, "TL SPO" }, + { "TR Ext Spk", NULL, "TR SPO" }, + { "WL Ext Spk", NULL, "WL SPO" }, + { "WR Ext Spk", NULL, "WR SPO" }, + + /* HP jack connectors - unknown if we have jack detection */ + { "Headphone Jack", NULL, "HPOL" }, + { "Headphone Jack", NULL, "HPOR" }, + + /* other jacks */ + { "IN1P", NULL, "Headset Mic" }, + + /* DMIC */ + { "DMic", NULL, "SoC DMIC" }, +}; + +static int cml_rt5682_codec_init(struct snd_soc_pcm_runtime *rtd) +{ + struct card_private *ctx = snd_soc_card_get_drvdata(rtd->card); + struct snd_soc_component *component = rtd->codec_dai->component; + struct snd_soc_jack *jack; + int ret; + + /* need to enable ASRC function for 24MHz mclk rate */ + rt5682_sel_asrc_clk_src(component, RT5682_DA_STEREO1_FILTER | + RT5682_AD_STEREO1_FILTER, + RT5682_CLK_SEL_I2S1_ASRC); + + /* + * Headset buttons map to the google Reference headset. + * These can be configured by userspace. + */ + ret = snd_soc_card_jack_new(rtd->card, "Headset Jack", + SND_JACK_HEADSET | SND_JACK_BTN_0 | + SND_JACK_BTN_1 | SND_JACK_BTN_2 | + SND_JACK_BTN_3, + &ctx->headset, NULL, 0); + if (ret) { + dev_err(rtd->dev, "Headset Jack creation failed: %d\n", ret); + return ret; + } + + jack = &ctx->headset; + + snd_jack_set_key(jack->jack, SND_JACK_BTN_0, KEY_PLAYPAUSE); + snd_jack_set_key(jack->jack, SND_JACK_BTN_1, KEY_VOICECOMMAND); + snd_jack_set_key(jack->jack, SND_JACK_BTN_2, KEY_VOLUMEUP); + snd_jack_set_key(jack->jack, SND_JACK_BTN_3, KEY_VOLUMEDOWN); + ret = snd_soc_component_set_jack(component, jack, NULL); + if (ret) + dev_err(rtd->dev, "Headset Jack call-back failed: %d\n", ret); + + return ret; +}; + +static int cml_rt5682_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct snd_soc_dai *codec_dai = rtd->codec_dai; + int clk_id, clk_freq, pll_out, ret; + + clk_id = RT5682_PLL1_S_MCLK; + clk_freq = CML_PLAT_CLK; + + pll_out = params_rate(params) * 512; + + ret = snd_soc_dai_set_pll(codec_dai, 0, clk_id, clk_freq, pll_out); + if (ret < 0) + dev_warn(rtd->dev, "snd_soc_dai_set_pll err = %d\n", ret); + + /* Configure sysclk for codec */ + ret = snd_soc_dai_set_sysclk(codec_dai, RT5682_SCLK_S_PLL1, + pll_out, SND_SOC_CLOCK_IN); + if (ret < 0) + dev_warn(rtd->dev, "snd_soc_dai_set_sysclk err = %d\n", ret); + + /* + * slot_width should be equal or large than data length, set them + * be the same + */ + ret = snd_soc_dai_set_tdm_slot(codec_dai, 0x0, 0x0, 2, + params_width(params)); + if (ret < 0) + dev_warn(rtd->dev, "set TDM slot err:%d\n", ret); + return ret; +} + +static int cml_rt1011_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct snd_soc_dai *codec_dai; + struct snd_soc_card *card = rtd->card; + int srate, i, ret = 0; + + srate = params_rate(params); + + for_each_rtd_codec_dai(rtd, i, codec_dai) { + /* 100 Fs to drive 24 bit data */ + ret = snd_soc_dai_set_pll(codec_dai, 0, RT1011_PLL1_S_BCLK, + 100 * srate, 256 * srate); + if (ret < 0) { + dev_err(card->dev, "codec_dai clock not set\n"); + return ret; + } + + ret = snd_soc_dai_set_sysclk(codec_dai, + RT1011_FS_SYS_PRE_S_PLL1, + 256 * srate, SND_SOC_CLOCK_IN); + if (ret < 0) { + dev_err(card->dev, "codec_dai clock not set\n"); + return ret; + } + + /* + * Codec TDM is configured as 24 bit capture/ playback. + * 2 CH PB is done over 4 codecs - 2 Woofers and 2 Tweeters. + * The Left woofer and tweeter plays the Left playback data + * and similar by the Right. + * Hence 2 codecs (1 T and 1 W pair) share same Rx slot. + * The feedback is captured for each codec individually. + * Hence all 4 codecs use 1 Tx slot each for feedback. + */ + if (!strcmp(codec_dai->component->name, "i2c-10EC1011:00")) { + ret = snd_soc_dai_set_tdm_slot(codec_dai, + 0x4, 0x1, 4, 24); + if (ret < 0) + break; + } + if (!strcmp(codec_dai->component->name, "i2c-10EC1011:02")) { + ret = snd_soc_dai_set_tdm_slot(codec_dai, + 0x1, 0x1, 4, 24); + if (ret < 0) + break; + } + /* TDM Rx slot 2 is used for Right Woofer & Tweeters pair */ + if (!strcmp(codec_dai->component->name, "i2c-10EC1011:01")) { + ret = snd_soc_dai_set_tdm_slot(codec_dai, + 0x8, 0x2, 4, 24); + if (ret < 0) + break; + } + if (!strcmp(codec_dai->component->name, "i2c-10EC1011:03")) { + ret = snd_soc_dai_set_tdm_slot(codec_dai, + 0x2, 0x2, 4, 24); + if (ret < 0) + break; + } + } + if (ret < 0) + dev_err(rtd->dev, + "set codec TDM slot for %s failed with error %d\n", + codec_dai->component->name, ret); + return ret; +} + +static struct snd_soc_ops cml_rt5682_ops = { + .hw_params = cml_rt5682_hw_params, +}; + +static const struct snd_soc_ops cml_rt1011_ops = { + .hw_params = cml_rt1011_hw_params, +}; + +static int sof_card_late_probe(struct snd_soc_card *card) +{ + struct card_private *ctx = snd_soc_card_get_drvdata(card); + struct snd_soc_component *component = NULL; + char jack_name[NAME_SIZE]; + struct hdmi_pcm *pcm; + int ret, i = 0; + + list_for_each_entry(pcm, &ctx->hdmi_pcm_list, head) { + component = pcm->codec_dai->component; + snprintf(jack_name, sizeof(jack_name), + "HDMI/DP, pcm=%d Jack", pcm->device); + ret = snd_soc_card_jack_new(card, jack_name, + SND_JACK_AVOUT, &hdmi_jack[i], + NULL, 0); + if (ret) + return ret; + + ret = hdac_hdmi_jack_init(pcm->codec_dai, pcm->device, + &hdmi_jack[i]); + if (ret < 0) + return ret; + + i++; + } + if (!component) + return -EINVAL; + + return hdac_hdmi_jack_port_init(component, &card->dapm); +} + +static int hdmi_init(struct snd_soc_pcm_runtime *rtd) +{ + struct card_private *ctx = snd_soc_card_get_drvdata(rtd->card); + struct snd_soc_dai *dai = rtd->codec_dai; + struct hdmi_pcm *pcm; + + pcm = devm_kzalloc(rtd->card->dev, sizeof(*pcm), GFP_KERNEL); + if (!pcm) + return -ENOMEM; + + pcm->device = dai->id; + pcm->codec_dai = dai; + + list_add_tail(&pcm->head, &ctx->hdmi_pcm_list); + + return 0; +} + +/* Cometlake digital audio interface glue - connects codec <--> CPU */ + +SND_SOC_DAILINK_DEF(ssp0_pin, + DAILINK_COMP_ARRAY(COMP_CPU("SSP0 Pin"))); +SND_SOC_DAILINK_DEF(ssp0_codec, + DAILINK_COMP_ARRAY(COMP_CODEC("i2c-10EC5682:00", + CML_RT5682_CODEC_DAI))); + +SND_SOC_DAILINK_DEF(ssp1_pin, + DAILINK_COMP_ARRAY(COMP_CPU("SSP1 Pin"))); +SND_SOC_DAILINK_DEF(ssp1_codec, + DAILINK_COMP_ARRAY( + /* WL */ COMP_CODEC("i2c-10EC1011:00", CML_RT1011_CODEC_DAI), + /* WR */ COMP_CODEC("i2c-10EC1011:01", CML_RT1011_CODEC_DAI), + /* TL */ COMP_CODEC("i2c-10EC1011:02", CML_RT1011_CODEC_DAI), + /* TR */ COMP_CODEC("i2c-10EC1011:03", CML_RT1011_CODEC_DAI))); + +SND_SOC_DAILINK_DEF(dmic_pin, + DAILINK_COMP_ARRAY(COMP_CPU("DMIC01 Pin"))); + +SND_SOC_DAILINK_DEF(dmic16k_pin, + DAILINK_COMP_ARRAY(COMP_CPU("DMIC16k Pin"))); + +SND_SOC_DAILINK_DEF(dmic_codec, + DAILINK_COMP_ARRAY(COMP_CODEC("dmic-codec", "dmic-hifi"))); + +SND_SOC_DAILINK_DEF(idisp1_pin, + DAILINK_COMP_ARRAY(COMP_CPU("iDisp1 Pin"))); +SND_SOC_DAILINK_DEF(idisp1_codec, + DAILINK_COMP_ARRAY(COMP_CODEC("ehdaudio0D2", "intel-hdmi-hifi1"))); + +SND_SOC_DAILINK_DEF(idisp2_pin, + DAILINK_COMP_ARRAY(COMP_CPU("iDisp2 Pin"))); +SND_SOC_DAILINK_DEF(idisp2_codec, + DAILINK_COMP_ARRAY(COMP_CODEC("ehdaudio0D2", "intel-hdmi-hifi2"))); + +SND_SOC_DAILINK_DEF(idisp3_pin, + DAILINK_COMP_ARRAY(COMP_CPU("iDisp3 Pin"))); +SND_SOC_DAILINK_DEF(idisp3_codec, + DAILINK_COMP_ARRAY(COMP_CODEC("ehdaudio0D2", "intel-hdmi-hifi3"))); + +SND_SOC_DAILINK_DEF(platform, + DAILINK_COMP_ARRAY(COMP_PLATFORM("0000:00:1f.3"))); + +static struct snd_soc_dai_link cml_rt1011_rt5682_dailink[] = { + /* Back End DAI links */ + { + /* SSP0 - Codec */ + .name = "SSP0-Codec", + .id = 0, + .init = cml_rt5682_codec_init, + .ignore_pmdown_time = 1, + .ops = &cml_rt5682_ops, + .dpcm_playback = 1, + .dpcm_capture = 1, + .no_pcm = 1, + SND_SOC_DAILINK_REG(ssp0_pin, ssp0_codec, platform), + }, + { + .name = "dmic01", + .id = 1, + .ignore_suspend = 1, + .dpcm_capture = 1, + .no_pcm = 1, + SND_SOC_DAILINK_REG(dmic_pin, dmic_codec, platform), + }, + { + .name = "dmic16k", + .id = 2, + .ignore_suspend = 1, + .dpcm_capture = 1, + .no_pcm = 1, + SND_SOC_DAILINK_REG(dmic16k_pin, dmic_codec, platform), + }, + { + .name = "iDisp1", + .id = 3, + .init = hdmi_init, + .dpcm_playback = 1, + .no_pcm = 1, + SND_SOC_DAILINK_REG(idisp1_pin, idisp1_codec, platform), + }, + { + .name = "iDisp2", + .id = 4, + .init = hdmi_init, + .dpcm_playback = 1, + .no_pcm = 1, + SND_SOC_DAILINK_REG(idisp2_pin, idisp2_codec, platform), + }, + { + .name = "iDisp3", + .id = 5, + .init = hdmi_init, + .dpcm_playback = 1, + .no_pcm = 1, + SND_SOC_DAILINK_REG(idisp3_pin, idisp3_codec, platform), + }, + { + /* + * SSP1 - Codec : added to end of list ensuring + * reuse of common topologies for other end points + * and changing only SSP1's codec + */ + .name = "SSP1-Codec", + .id = 6, + .dpcm_playback = 1, + .dpcm_capture = 1, /* Capture stream provides Feedback */ + .no_pcm = 1, + .ops = &cml_rt1011_ops, + SND_SOC_DAILINK_REG(ssp1_pin, ssp1_codec, platform), + }, +}; + +static struct snd_soc_codec_conf rt1011_conf[] = { + { + .dev_name = "i2c-10EC1011:00", + .name_prefix = "WL", + }, + { + .dev_name = "i2c-10EC1011:01", + .name_prefix = "WR", + }, + { + .dev_name = "i2c-10EC1011:02", + .name_prefix = "TL", + }, + { + .dev_name = "i2c-10EC1011:03", + .name_prefix = "TR", + }, +}; + +/* Cometlake audio machine driver for RT1011 and RT5682 */ +static struct snd_soc_card snd_soc_card_cml = { + .name = "cml_rt1011_rt5682", + .dai_link = cml_rt1011_rt5682_dailink, + .num_links = ARRAY_SIZE(cml_rt1011_rt5682_dailink), + .codec_conf = rt1011_conf, + .num_configs = ARRAY_SIZE(rt1011_conf), + .dapm_widgets = cml_rt1011_rt5682_widgets, + .num_dapm_widgets = ARRAY_SIZE(cml_rt1011_rt5682_widgets), + .dapm_routes = cml_rt1011_rt5682_map, + .num_dapm_routes = ARRAY_SIZE(cml_rt1011_rt5682_map), + .controls = cml_controls, + .num_controls = ARRAY_SIZE(cml_controls), + .fully_routed = true, + .late_probe = sof_card_late_probe, +}; + +static int snd_cml_rt1011_probe(struct platform_device *pdev) +{ + struct card_private *ctx; + struct snd_soc_acpi_mach *mach; + const char *platform_name; + int ret; + + ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_ATOMIC); + if (!ctx) + return -ENOMEM; + + INIT_LIST_HEAD(&ctx->hdmi_pcm_list); + mach = (&pdev->dev)->platform_data; + snd_soc_card_cml.dev = &pdev->dev; + platform_name = mach->mach_params.platform; + + /* set platform name for each dailink */ + ret = snd_soc_fixup_dai_links_platform_name(&snd_soc_card_cml, + platform_name); + if (ret) + return ret; + snd_soc_card_set_drvdata(&snd_soc_card_cml, ctx); + + return devm_snd_soc_register_card(&pdev->dev, &snd_soc_card_cml); +} + +static struct platform_driver snd_cml_rt1011_rt5682_driver = { + .probe = snd_cml_rt1011_probe, + .driver = { + .name = "cml_rt1011_rt5682", + .pm = &snd_soc_pm_ops, + }, +}; +module_platform_driver(snd_cml_rt1011_rt5682_driver); + +/* Module information */ +MODULE_DESCRIPTION("Cometlake Audio Machine driver - RT1011 and RT5682 in I2S mode"); +MODULE_AUTHOR("Naveen Manohar naveen.m@intel.com"); +MODULE_AUTHOR("Sathya Prakash M R sathya.prakash.m.r@intel.com"); +MODULE_AUTHOR("Shuming Fan shumingf@realtek.com"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:cml_rt1011_rt5682");