[alsa-devel] Gigabyte ALC889A Function ID: 0x01
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry
Another thing I noticed is that aplay -l reports two different things. both using 1.0.19.
On the motherboard that works: alsamixer reports ALC889A aplay -l reports: **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: ALC883 Analog [ALC883 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: SB [HDA ATI SB], device 1: ALC883 Digital [ALC883 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: HDMI [HDA ATI HDMI], device 3: ATI HDMI [ATI HDMI] Subdevices: 0/1 Subdevice #0: subdevice #0
on the motherboard that does NOT work: alsamixer reports ALC889A aplay -l reports: **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: ALC885 Analog [ALC885 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: SB [HDA ATI SB], device 1: ALC885 Digital [ALC885 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: HDMI [HDA ATI HDMI], device 3: ATI HDMI [ATI HDMI] Subdevices: 0/1 Subdevice #0: subdevice #0
The lspci reports the same for both motherboards: 1002:960f
HOW - is the motherboard that is not working getting ALC885??? Why is not getting ALC883? as the ALC883 works on the other motherboard?
Jerry
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
I noticed the subsystem a002 and a022 is different. Can this be why its not working?
Any thoughts?
Jerry
At Wed, 15 Apr 2009 10:45:43 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
How are you testing HDMI output?
Takashi
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:45:43 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
How are you testing HDMI output?
Takashi
I have a sharp aquos HDMI that works with the other motherboard.
I am just switching between the two.
I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
Jerry
At Wed, 15 Apr 2009 11:14:20 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:45:43 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
How are you testing HDMI output?
Takashi
I have a sharp aquos HDMI that works with the other motherboard.
I am just switching between the two.
I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
More exactly?
Also, try like below: % aplay -Dhdmi:1 foo.wav
Takashi
Takashi Iwai wrote:
At Wed, 15 Apr 2009 11:14:20 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:45:43 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio.
I am trying 1.0.19 and audio works out the analog back port but not over HDMI.
Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
Codec: Realtek ALC889A Address: 0 Function Id: 0x1 <--------------------------------- this is different Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x02 [Audio Output] wcaps 0x11: Stereo Converter: stream=0, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo
I have been looking but havent found a solution yet. I tried grabbing the snapshot tar ball for today but I get errors on the compile.
I had a similiar motherboard but it does not report Function ID: 01 : - HDMI audio on this board works correctly. Codec: Realtek ALC889A Address: 0 Vendor Id: 0x10ec0885 Subsystem Id: 0x1458a002 Revision Id: 0x100101 No Modem Function Group found Default PCM: rates [0x560]: 44100 48000 96000 192000
Any thoughts????
Jerry _______________________________________________ Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
How are you testing HDMI output?
Takashi
I have a sharp aquos HDMI that works with the other motherboard.
I am just switching between the two.
I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
More exactly?
Also, try like below: % aplay -Dhdmi:1 foo.wav
Takashi
When I run your command : aplay -Dhdmi:1 /tmp/NewVoiceMale.wav aplay: main:590: audio open error: Device or resource busy
when I run my command aplay /tmp/NewVoiceMail.wav it plays the file (no audio though).
asound.conf has hw:1,3 for my device. if I change it to hw:0,0 I get analog audio out the back.
jerry
At Wed, 15 Apr 2009 11:34:23 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 11:14:20 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:45:43 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:00:33 -0400, Jerry Geis wrote:
> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio. > > I am trying 1.0.19 and audio works out the analog back port but not over > HDMI. > > > Never mind about "Function ID" entry. It's just a new line that was added recently. function_id=1 means it's an audio codec.
The way HDMI is supported are mainly either through the same audio codec (ALC889A) or through a dedicated HDMI codec. In the former case, you'll likely see a word "HDMI" in the digital output pin of the codec proc file. In the latter case, you must have a different codec chip connected to the HD-audio bus with a different codec address number.
Takashi
> Codec: Realtek ALC889A > Address: 0 > Function Id: 0x1 > <--------------------------------- this is different > Vendor Id: 0x10ec0885 > Subsystem Id: 0x1458a002 > Revision Id: 0x100101 > No Modem Function Group found > Default PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Default Amp-In caps: N/A > Default Amp-Out caps: N/A > GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 > IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 > IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 > Node 0x02 [Audio Output] wcaps 0x11: Stereo > Converter: stream=0, channel=0 > PCM: > rates [0x560]: 44100 48000 96000 192000 > bits [0xe]: 16 20 24 > formats [0x1]: PCM > Node 0x03 [Audio Output] wcaps 0x11: Stereo > > I have been looking but havent found a solution yet. I tried grabbing > the snapshot tar ball for today but I get errors on the compile. > > I had a similiar motherboard but it does not report Function ID: 01 : - > HDMI audio on this board works correctly. > Codec: Realtek ALC889A > Address: 0 > Vendor Id: 0x10ec0885 > Subsystem Id: 0x1458a002 > Revision Id: 0x100101 > No Modem Function Group found > Default PCM: > rates [0x560]: 44100 48000 96000 192000 > > Any thoughts???? > > Jerry > _______________________________________________ > Alsa-devel mailing list > Alsa-devel@alsa-project.org > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel > > > >
I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
How are you testing HDMI output?
Takashi
I have a sharp aquos HDMI that works with the other motherboard.
I am just switching between the two.
I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
More exactly?
Also, try like below: % aplay -Dhdmi:1 foo.wav
Takashi
When I run your command : aplay -Dhdmi:1 /tmp/NewVoiceMale.wav aplay: main:590: audio open error: Device or resource busy
Is /dev/snd/hwC1D*p device being used by some app, such as a sound daemon?
Takashi
Takashi Iwai wrote:
At Wed, 15 Apr 2009 11:34:23 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 11:14:20 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
At Wed, 15 Apr 2009 10:45:43 -0400, Jerry Geis wrote:
Takashi Iwai wrote:
> At Wed, 15 Apr 2009 10:00:33 -0400, > Jerry Geis wrote: > > > > >> I am using the gigabyte MA78GM-US2H motherboard. it has the ALC889A audio. >> >> I am trying 1.0.19 and audio works out the analog back port but not over >> HDMI. >> >> >> >> > Never mind about "Function ID" entry. It's just a new line that was > added recently. function_id=1 means it's an audio codec. > > The way HDMI is supported are mainly either through the same audio > codec (ALC889A) or through a dedicated HDMI codec. In the former > case, you'll likely see a word "HDMI" in the digital output pin of the > codec proc file. In the latter case, you must have a different codec > chip connected to the HD-audio bus with a different codec address > number. > > > Takashi > > > > > > >> Codec: Realtek ALC889A >> Address: 0 >> Function Id: 0x1 >> <--------------------------------- this is different >> Vendor Id: 0x10ec0885 >> Subsystem Id: 0x1458a002 >> Revision Id: 0x100101 >> No Modem Function Group found >> Default PCM: >> rates [0x560]: 44100 48000 96000 192000 >> bits [0xe]: 16 20 24 >> formats [0x1]: PCM >> Default Amp-In caps: N/A >> Default Amp-Out caps: N/A >> GPIO: io=2, o=0, i=0, unsolicited=1, wake=0 >> IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 >> IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 >> Node 0x02 [Audio Output] wcaps 0x11: Stereo >> Converter: stream=0, channel=0 >> PCM: >> rates [0x560]: 44100 48000 96000 192000 >> bits [0xe]: 16 20 24 >> formats [0x1]: PCM >> Node 0x03 [Audio Output] wcaps 0x11: Stereo >> >> I have been looking but havent found a solution yet. I tried grabbing >> the snapshot tar ball for today but I get errors on the compile. >> >> I had a similiar motherboard but it does not report Function ID: 01 : - >> HDMI audio on this board works correctly. >> Codec: Realtek ALC889A >> Address: 0 >> Vendor Id: 0x10ec0885 >> Subsystem Id: 0x1458a002 >> Revision Id: 0x100101 >> No Modem Function Group found >> Default PCM: >> rates [0x560]: 44100 48000 96000 192000 >> >> Any thoughts???? >> >> Jerry >> _______________________________________________ >> Alsa-devel mailing list >> Alsa-devel@alsa-project.org >> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel >> >> >> >> >> > > > > I upload alsa-info.sh
for the NOT WORKIng one http://www.alsa-project.org/db/?f=7e8bc9485e8bb98bf15dae5a0d5dc038003c3203
for the working on http://www.alsa-project.org/db/?f=a18bcb6e87fe33a7365a749d0877a4546e901bf2
How are you testing HDMI output?
Takashi
I have a sharp aquos HDMI that works with the other motherboard.
I am just switching between the two.
I have the asound.conf set to the correct hw:X,y on both machines for HDMI.
More exactly?
Also, try like below: % aplay -Dhdmi:1 foo.wav
Takashi
When I run your command : aplay -Dhdmi:1 /tmp/NewVoiceMale.wav aplay: main:590: audio open error: Device or resource busy
Is /dev/snd/hwC1D*p device being used by some app, such as a sound daemon?
Takashi
The file is present and doesnt seem to be used by anyone. lsof | grep hwC1
jerry
participants (2)
-
Jerry Geis -
Takashi Iwai