Add mixer quirk for the Focusrite Scarlett 6i6, 18i8, and 18i20 Gen 2 audio interfaces. Although the interfaces are USB compliant, additional input/output level controls and hardware routing/mixing functionality are available using proprietary USB requests.

Signed-off-by: Geoffrey D. Bennett g@b4.vu --- Hi all,

This patch adds the following controls for the Scarlett 6i6, 18i8, and 18i20 Gen 2: - Master volume knob indicator (18i20 only) - Mute and dim switches (18i20 only) - Volume controls for the analogue HW outputs - HW/SW volume switches for the 10 analogue HW outputs (18i20 only) - Line Level/Instrument Level and Pad controls (6i6 and 18i8 only) - Output mux (where the sound for the HW outputs comes from; defaults to PCM outputs) - Capture mux (where the sound for PCM recording comes from; defaults to HW inputs) - Matrix mux (where the sound going into the mixer comes from; 18 inputs default off) - Mixer matrix (18 inputs * 10 outputs = 180 controls) - Level meters

Changes since v1: - Add support for the Scarlett 18i8 Gen 2 - Save configuration parameters to NVRAM - Implemented feedback from Takashi's email 24/Apr/2019 - Moved private field from struct snd_usb_audio to struct usb_mixer_interface - Added timer and buffer fields to struct usb_mixer_interface - Other small code fixes/cleanups/improvements

Changes since v2: - Add support for the Scarlett 6i6 Gen 2 - Add support for controlling the mute/dim switches (18i20 only) - Implemented feedback from Takashi's email 29/Apr/2019: One pointer field private_data and one function pointer private_free. Replaced timer with delayed work (thanks for that suggestion; it makes the code a *lot* simpler!). - The new functionality is disabled by default as there were reports of some Gen 2 devices not responding to the initialisation sequence and hanging. Added module parameter "scarlett_gen2_mixer_enable". If this parameter is not set, logs a message "Focusrite Scarlett Gen 2 Mixer Driver disabled; use options snd_usb_audio scarlett_gen2_mixer_enable=1 to enable and report any issues to g@b4.vu".

Changes since v3: - No functional changes; fix checkpatch.pl error and typo in declaration.

Changes since v4: - Implemented feedback from Takashi's email 9/Jul/2019: cancel delayed work on suspend, drop copyright texts, remove unnecessary blank lines, and run kmalloc outside the mutex.

Changes since v5: - Implemented feedback from Takashi's emails 9-10/Jul/2019: use chip->setup value (device_setup option) instead of the scarlett_gen2_mixer_enable option and sync config to NVRAM immediately on suspend. - Fixed issue where the config save delayed work would be cancelled and not restarted if a scarlett2_*_ctl_put() function was called and the parameter value was not changed. - Renaming definitions and functions for consistency and move private free/suspend functions above their use so pre-declaration isn't necessary.

Changes since v6: - Implemented feedback from Takashi's email 18/Jul/2019: use snd_usb_pipe_sanity_check() to verify pipe, and initialise pointers as "NULL" not "0".

diff --git a/sound/usb/Makefile b/sound/usb/Makefile index e1ce257ab705..f4b7384caa9d 100644 --- a/sound/usb/Makefile +++ b/sound/usb/Makefile @@ -11,6 +11,7 @@ snd-usb-audio-objs := card.o \ mixer.o \ mixer_quirks.o \ mixer_scarlett.o \ + mixer_scarlett_gen2.o \ mixer_us16x08.o \ pcm.o \ power.o \ diff --git a/sound/usb/mixer.c b/sound/usb/mixer.c index 7498b5191b68..7b51ab4c35b0 100644 --- a/sound/usb/mixer.c +++ b/sound/usb/mixer.c @@ -3509,6 +3509,8 @@ void snd_usb_mixer_disconnect(struct usb_mixer_interface *mixer) usb_kill_urb(mixer->urb); if (mixer->rc_urb) usb_kill_urb(mixer->rc_urb); + if (mixer->private_free) + mixer->private_free(mixer); mixer->disconnected = true; }

@@ -3536,6 +3538,8 @@ static int snd_usb_mixer_activate(struct usb_mixer_interface *mixer) int snd_usb_mixer_suspend(struct usb_mixer_interface *mixer) { snd_usb_mixer_inactivate(mixer); + if (mixer->private_suspend) + mixer->private_suspend(mixer); return 0; }

diff --git a/sound/usb/mixer.h b/sound/usb/mixer.h index 394cd9107507..37e1b234c802 100644 --- a/sound/usb/mixer.h +++ b/sound/usb/mixer.h @@ -28,6 +28,10 @@ struct usb_mixer_interface { struct media_mixer_ctl *media_mixer_ctl;

bool disconnected; + + void *private_data; + void (*private_free)(struct usb_mixer_interface *mixer); + void (*private_suspend)(struct usb_mixer_interface *mixer); };

#define MAX_CHANNELS 16 /* max logical channels */ diff --git a/sound/usb/mixer_quirks.c b/sound/usb/mixer_quirks.c index 199fa157a411..70805c15b0b5 100644 --- a/sound/usb/mixer_quirks.c +++ b/sound/usb/mixer_quirks.c @@ -32,6 +32,7 @@ #include "mixer.h" #include "mixer_quirks.h" #include "mixer_scarlett.h" +#include "mixer_scarlett_gen2.h" #include "mixer_us16x08.h" #include "helper.h"

@@ -2258,6 +2259,12 @@ int snd_usb_mixer_apply_create_quirk(struct usb_mixer_interface *mixer) err = snd_scarlett_controls_create(mixer); break;

+ case USB_ID(0x1235, 0x8203): /* Focusrite Scarlett 6i6 2nd Gen */ + case USB_ID(0x1235, 0x8204): /* Focusrite Scarlett 18i8 2nd Gen */ + case USB_ID(0x1235, 0x8201): /* Focusrite Scarlett 18i20 2nd Gen */ + err = snd_scarlett_gen2_controls_create(mixer); + break; + case USB_ID(0x041e, 0x323b): /* Creative Sound Blaster E1 */ err = snd_soundblaster_e1_switch_create(mixer); break; diff --git a/sound/usb/mixer_scarlett_gen2.c b/sound/usb/mixer_scarlett_gen2.c new file mode 100644 index 000000000000..7d460b1f1735 --- /dev/null +++ b/sound/usb/mixer_scarlett_gen2.c @@ -0,0 +1,2075 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Focusrite Scarlett 6i6/18i8/18i20 Gen 2 Driver for ALSA + * + * Copyright (c) 2018-2019 by Geoffrey D. Bennett <g at b4.vu> + * + * Based on the Scarlett (Gen 1) Driver for ALSA: + * + * Copyright (c) 2013 by Tobias Hoffmann + * Copyright (c) 2013 by Robin Gareus <robin at gareus.org> + * Copyright (c) 2002 by Takashi Iwai <tiwai at suse.de> + * Copyright (c) 2014 by Chris J Arges <chris.j.arges at canonical.com> + * + * Many codes borrowed from audio.c by + * Alan Cox (alan at lxorguk.ukuu.org.uk) + * Thomas Sailer (sailer at ife.ee.ethz.ch) + * + * Code cleanup: + * David Henningsson <david.henningsson at canonical.com> + */ + +/* Mixer Interface for the Focusrite Scarlett 6i6/18i8/18i20 Gen 2 audio + * interface. Based on the Gen 1 driver and rewritten. + */ + +/* The protocol was reverse engineered by looking at the communication + * between Focusrite Control 2.3.4 and the Focusrite(R) Scarlett 18i20 + * (firmware 1083) using usbmon in July-August 2018. + * + * Scarlett 18i8 support added in April 2019. + * + * Scarlett 6i6 support added in June 2019 (thanks to Martin Wittmann + * for providing usbmon output and testing). + * + * This ALSA mixer gives access to: + * - input, output, mixer-matrix muxes + * - 18x10 mixer-matrix gain stages + * - gain/volume controls + * - level meters + * - line/inst level and pad controls + * + * <ditaa> + * /--------------\ 18chn 20chn /--------------\ + * | Hardware in +--+------\ /-------------+--+ ALSA PCM out | + * --------------/ | | | | --------------/ + * | | | /-----\ | + * | | | | | | + * | v v v | | + * | +---------------+ | | + * | \ Matrix Mux / | | + * | +-----+-----+ | | + * | | | | + * | |18chn | | + * | | | | + * | | 10chn| | + * | v | | + * | +------------+ | | + * | | Mixer | | | + * | | Matrix | | | + * | | | | | + * | | 18x10 Gain | | | + * | | stages | | | + * | +-----+------+ | | + * | | | | + * |18chn |10chn | |20chn + * | | | | + * | +----------/ | + * | | | + * v v v + * =========================== + * +---------------+ +--—------------+ + * \ Output Mux / \ Capture Mux / + * +---+---+---+ +-----+-----+ + * | | | + * 10chn| | |18chn + * | | | + * /--------------\ | | | /--------------\ + * | S/PDIF, ADAT |<--/ |10chn -->| ALSA PCM in | + * | Hardware out | | --------------/ + * --------------/ | + * v + * +-------------+ Software gain per channel. + * | Master Gain |<-- 18i20 only: Switch per channel + * +------+------+ to select HW or SW gain control. + * | + * |10chn + * /--------------\ | + * | Analogue |<------/ + * | Hardware out | + * --------------/ + * </ditaa> + * + */ + +#include <linux/slab.h> +#include <linux/usb.h> +#include <linux/moduleparam.h> + +#include <sound/control.h> +#include <sound/tlv.h> + +#include "usbaudio.h" +#include "mixer.h" +#include "helper.h" + +#include "mixer_scarlett_gen2.h" + +/* device_setup value to enable */ +#define SCARLETT2_ENABLE 0x01 + +/* some gui mixers can't handle negative ctl values */ +#define SCARLETT2_VOLUME_BIAS 127 + +/* mixer range from -80dB to +6dB in 0.5dB steps */ +#define SCARLETT2_MIXER_MIN_DB -80 +#define SCARLETT2_MIXER_BIAS (-SCARLETT2_MIXER_MIN_DB * 2) +#define SCARLETT2_MIXER_MAX_DB 6 +#define SCARLETT2_MIXER_MAX_VALUE \ + ((SCARLETT2_MIXER_MAX_DB - SCARLETT2_MIXER_MIN_DB) * 2) + +/* map from (dB + 80) * 2 to mixer value + * for dB in 0 .. 172: int(8192 * pow(10, ((dB - 160) / 2 / 20))) + */ +static const u16 scarlett2_mixer_values[173] = { + 0, 0, 0, 0, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, + 2, 2, 3, 3, 3, 3, 3, 4, 4, 4, 4, 5, 5, 5, 6, 6, 6, 7, 7, 8, 8, + 9, 9, 10, 10, 11, 12, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, + 23, 24, 25, 27, 29, 30, 32, 34, 36, 38, 41, 43, 46, 48, 51, + 54, 57, 61, 65, 68, 73, 77, 81, 86, 91, 97, 103, 109, 115, + 122, 129, 137, 145, 154, 163, 173, 183, 194, 205, 217, 230, + 244, 259, 274, 290, 307, 326, 345, 365, 387, 410, 434, 460, + 487, 516, 547, 579, 614, 650, 689, 730, 773, 819, 867, 919, + 973, 1031, 1092, 1157, 1225, 1298, 1375, 1456, 1543, 1634, + 1731, 1833, 1942, 2057, 2179, 2308, 2445, 2590, 2744, 2906, + 3078, 3261, 3454, 3659, 3876, 4105, 4349, 4606, 4879, 5168, + 5475, 5799, 6143, 6507, 6892, 7301, 7733, 8192, 8677, 9191, + 9736, 10313, 10924, 11571, 12257, 12983, 13752, 14567, 15430, + 16345 +}; + +/* Maximum number of analogue outputs */ +#define SCARLETT2_ANALOGUE_MAX 10 + +/* Maximum number of level and pad switches */ +#define SCARLETT2_LEVEL_SWITCH_MAX 2 +#define SCARLETT2_PAD_SWITCH_MAX 4 + +/* Maximum number of inputs to the mixer */ +#define SCARLETT2_INPUT_MIX_MAX 18 + +/* Maximum number of outputs from the mixer */ +#define SCARLETT2_OUTPUT_MIX_MAX 10 + +/* Maximum size of the data in the USB mux assignment message: + * 18 inputs, 20 outputs, 18 matrix inputs, 8 spare + */ +#define SCARLETT2_MUX_MAX 64 + +/* Number of meters: + * 18 inputs, 20 outputs, 18 matrix inputs + */ +#define SCARLETT2_NUM_METERS 56 + +/* Hardware port types: + * - None (no input to mux) + * - Analogue I/O + * - S/PDIF I/O + * - ADAT I/O + * - Mixer I/O + * - PCM I/O + */ +enum { + SCARLETT2_PORT_TYPE_NONE = 0, + SCARLETT2_PORT_TYPE_ANALOGUE = 1, + SCARLETT2_PORT_TYPE_SPDIF = 2, + SCARLETT2_PORT_TYPE_ADAT = 3, + SCARLETT2_PORT_TYPE_MIX = 4, + SCARLETT2_PORT_TYPE_PCM = 5, + SCARLETT2_PORT_TYPE_COUNT = 6, +}; + +/* Count of total I/O and number available at each sample rate */ +enum { + SCARLETT2_PORT_IN = 0, + SCARLETT2_PORT_OUT = 1, + SCARLETT2_PORT_OUT_44 = 2, + SCARLETT2_PORT_OUT_88 = 3, + SCARLETT2_PORT_OUT_176 = 4, + SCARLETT2_PORT_DIRECTIONS = 5, +}; + +/* Hardware buttons on the 18i20 */ +#define SCARLETT2_BUTTON_MAX 2 + +static const char *const scarlett2_button_names[SCARLETT2_BUTTON_MAX] = { + "Mute", "Dim" +}; + +/* Description of each hardware port type: + * - id: hardware ID for this port type + * - num: number of sources/destinations of this port type + * - src_descr: printf format string for mux input selections + * - src_num_offset: added to channel number for the fprintf + * - dst_descr: printf format string for mixer controls + */ +struct scarlett2_ports { + u16 id; + int num[SCARLETT2_PORT_DIRECTIONS]; + const char * const src_descr; + int src_num_offset; + const char * const dst_descr; +}; + +struct scarlett2_device_info { + u8 line_out_hw_vol; /* line out hw volume is sw controlled */ + u8 button_count; /* number of buttons */ + u8 level_input_count; /* inputs with level selectable */ + u8 pad_input_count; /* inputs with pad selectable */ + const char * const line_out_descrs[SCARLETT2_ANALOGUE_MAX]; + struct scarlett2_ports ports[SCARLETT2_PORT_TYPE_COUNT]; +}; + +struct scarlett2_mixer_data { + struct usb_mixer_interface *mixer; + struct mutex usb_mutex; /* prevent sending concurrent USB requests */ + struct mutex data_mutex; /* lock access to this data */ + struct delayed_work work; + const struct scarlett2_device_info *info; + int num_mux_srcs; + u16 scarlett2_seq; + u8 vol_updated; + u8 master_vol; + u8 vol[SCARLETT2_ANALOGUE_MAX]; + u8 vol_sw_hw_switch[SCARLETT2_ANALOGUE_MAX]; + u8 level_switch[SCARLETT2_LEVEL_SWITCH_MAX]; + u8 pad_switch[SCARLETT2_PAD_SWITCH_MAX]; + u8 buttons[SCARLETT2_BUTTON_MAX]; + struct snd_kcontrol *master_vol_ctl; + struct snd_kcontrol *vol_ctls[SCARLETT2_ANALOGUE_MAX]; + struct snd_kcontrol *button_ctls[SCARLETT2_BUTTON_MAX]; + u8 mux[SCARLETT2_MUX_MAX]; + u8 mix[SCARLETT2_INPUT_MIX_MAX * SCARLETT2_OUTPUT_MIX_MAX]; +}; + +/*** Model-specific data ***/ + +static const struct scarlett2_device_info s6i6_gen2_info = { + /* The first two analogue inputs can be switched between line + * and instrument levels. + */ + .level_input_count = 2, + + /* The first two analogue inputs have an optional pad. */ + .pad_input_count = 2, + + .line_out_descrs = { + "Monitor L", + "Monitor R", + "Headphones L", + "Headphones R", + }, + + .ports = { + { + .id = 0x000, + .num = { 1, 0, 8, 8, 8 }, + .src_descr = "Off", + .src_num_offset = 0, + }, + { + .id = 0x080, + .num = { 4, 4, 4, 4, 4 }, + .src_descr = "Analogue %d", + .src_num_offset = 1, + .dst_descr = "Analogue Output %02d Playback" + }, + { + .id = 0x180, + .num = { 2, 2, 2, 2, 2 }, + .src_descr = "S/PDIF %d", + .src_num_offset = 1, + .dst_descr = "S/PDIF Output %d Playback" + }, + { + .id = 0x300, + .num = { 10, 18, 18, 18, 18 }, + .src_descr = "Mix %c", + .src_num_offset = 65, + .dst_descr = "Mixer Input %02d Capture" + }, + { + .id = 0x600, + .num = { 6, 6, 6, 6, 6 }, + .src_descr = "PCM %d", + .src_num_offset = 1, + .dst_descr = "PCM %02d Capture" + }, + }, +}; + +static const struct scarlett2_device_info s18i8_gen2_info = { + /* The first two analogue inputs can be switched between line + * and instrument levels. + */ + .level_input_count = 2, + + /* The first four analogue inputs have an optional pad. */ + .pad_input_count = 4, + + .line_out_descrs = { + "Monitor L", + "Monitor R", + "Headphones 1 L", + "Headphones 1 R", + "Headphones 2 L", + "Headphones 2 R", + }, + + .ports = { + { + .id = 0x000, + .num = { 1, 0, 8, 8, 4 }, + .src_descr = "Off", + .src_num_offset = 0, + }, + { + .id = 0x080, + .num = { 8, 6, 6, 6, 6 }, + .src_descr = "Analogue %d", + .src_num_offset = 1, + .dst_descr = "Analogue Output %02d Playback" + }, + { + /* S/PDIF outputs aren't available at 192KHz + * but are included in the USB mux I/O + * assignment message anyway + */ + .id = 0x180, + .num = { 2, 2, 2, 2, 2 }, + .src_descr = "S/PDIF %d", + .src_num_offset = 1, + .dst_descr = "S/PDIF Output %d Playback" + }, + { + .id = 0x200, + .num = { 8, 0, 0, 0, 0 }, + .src_descr = "ADAT %d", + .src_num_offset = 1, + }, + { + .id = 0x300, + .num = { 10, 18, 18, 18, 18 }, + .src_descr = "Mix %c", + .src_num_offset = 65, + .dst_descr = "Mixer Input %02d Capture" + }, + { + .id = 0x600, + .num = { 20, 18, 18, 14, 10 }, + .src_descr = "PCM %d", + .src_num_offset = 1, + .dst_descr = "PCM %02d Capture" + }, + }, +}; + +static const struct scarlett2_device_info s18i20_gen2_info = { + /* The analogue line outputs on the 18i20 can be switched + * between software and hardware volume control + */ + .line_out_hw_vol = 1, + + /* Mute and dim buttons */ + .button_count = 2, + + .line_out_descrs = { + "Monitor L", + "Monitor R", + NULL, + NULL, + NULL, + NULL, + "Headphones 1 L", + "Headphones 1 R", + "Headphones 2 L", + "Headphones 2 R", + }, + + .ports = { + { + .id = 0x000, + .num = { 1, 0, 8, 8, 6 }, + .src_descr = "Off", + .src_num_offset = 0, + }, + { + .id = 0x080, + .num = { 8, 10, 10, 10, 10 }, + .src_descr = "Analogue %d", + .src_num_offset = 1, + .dst_descr = "Analogue Output %02d Playback" + }, + { + /* S/PDIF outputs aren't available at 192KHz + * but are included in the USB mux I/O + * assignment message anyway + */ + .id = 0x180, + .num = { 2, 2, 2, 2, 2 }, + .src_descr = "S/PDIF %d", + .src_num_offset = 1, + .dst_descr = "S/PDIF Output %d Playback" + }, + { + .id = 0x200, + .num = { 8, 8, 8, 4, 0 }, + .src_descr = "ADAT %d", + .src_num_offset = 1, + .dst_descr = "ADAT Output %d Playback" + }, + { + .id = 0x300, + .num = { 10, 18, 18, 18, 18 }, + .src_descr = "Mix %c", + .src_num_offset = 65, + .dst_descr = "Mixer Input %02d Capture" + }, + { + .id = 0x600, + .num = { 20, 18, 18, 14, 10 }, + .src_descr = "PCM %d", + .src_num_offset = 1, + .dst_descr = "PCM %02d Capture" + }, + }, +}; + +/* get the starting port index number for a given port type/direction */ +static int scarlett2_get_port_start_num(const struct scarlett2_ports *ports, + int direction, int port_type) +{ + int i, num = 0; + + for (i = 0; i < port_type; i++) + num += ports[i].num[direction]; + + return num; +} + +/*** USB Interactions ***/ + +/* Vendor-Specific Interface, Endpoint, MaxPacketSize, Interval */ +#define SCARLETT2_USB_VENDOR_SPECIFIC_INTERFACE 5 +#define SCARLETT2_USB_INTERRUPT_ENDPOINT 4 +#define SCARLETT2_USB_INTERRUPT_MAX_DATA 64 +#define SCARLETT2_USB_INTERRUPT_INTERVAL 3 + +/* Interrupt flags for volume and mute/dim button changes */ +#define SCARLETT2_USB_INTERRUPT_VOL_CHANGE 0x400000 +#define SCARLETT2_USB_INTERRUPT_BUTTON_CHANGE 0x200000 + +/* Commands for sending/receiving requests/responses */ +#define SCARLETT2_USB_VENDOR_SPECIFIC_CMD_REQ 2 +#define SCARLETT2_USB_VENDOR_SPECIFIC_CMD_RESP 3 + +#define SCARLETT2_USB_INIT_SEQ 0x00000000 +#define SCARLETT2_USB_GET_METER_LEVELS 0x00001001 +#define SCARLETT2_USB_SET_MIX 0x00002002 +#define SCARLETT2_USB_SET_MUX 0x00003002 +#define SCARLETT2_USB_GET_DATA 0x00800000 +#define SCARLETT2_USB_SET_DATA 0x00800001 +#define SCARLETT2_USB_DATA_CMD 0x00800002 +#define SCARLETT2_USB_CONFIG_SAVE 6 + +#define SCARLETT2_USB_VOLUME_STATUS_OFFSET 0x31 +#define SCARLETT2_USB_METER_LEVELS_GET_MAGIC 1 + +/* volume status is read together (matches scarlett2_config_items[]) */ +struct scarlett2_usb_volume_status { + /* mute & dim buttons */ + u8 buttons[SCARLETT2_BUTTON_MAX]; + + u8 pad1; + + /* software volume setting */ + s16 sw_vol[SCARLETT2_ANALOGUE_MAX]; + + /* actual volume of output inc. dim (-18dB) */ + s16 hw_vol[SCARLETT2_ANALOGUE_MAX]; + + u8 pad2[SCARLETT2_ANALOGUE_MAX]; + + /* sw (0) or hw (1) controlled */ + u8 sw_hw_switch[SCARLETT2_ANALOGUE_MAX]; + + u8 pad3[6]; + + /* front panel volume knob */ + s16 master_vol; +} __packed; + +/* Configuration parameters that can be read and written */ +enum { + SCARLETT2_CONFIG_BUTTONS = 0, + SCARLETT2_CONFIG_LINE_OUT_VOLUME = 1, + SCARLETT2_CONFIG_SW_HW_SWITCH = 2, + SCARLETT2_CONFIG_LEVEL_SWITCH = 3, + SCARLETT2_CONFIG_PAD_SWITCH = 4, + SCARLETT2_CONFIG_COUNT = 5 +}; + +/* Location, size, and activation command number for the configuration + * parameters + */ +struct scarlett2_config { + u8 offset; + u8 size; + u8 activate; +}; + +static const struct scarlett2_config + scarlett2_config_items[SCARLETT2_CONFIG_COUNT] = { + /* Mute/Dim Buttons */ + { + .offset = 0x31, + .size = 1, + .activate = 2 + }, + + /* Line Out Volume */ + { + .offset = 0x34, + .size = 2, + .activate = 1 + }, + + /* SW/HW Volume Switch */ + { + .offset = 0x66, + .size = 1, + .activate = 3 + }, + + /* Level Switch */ + { + .offset = 0x7c, + .size = 1, + .activate = 7 + }, + + /* Pad Switch */ + { + .offset = 0x84, + .size = 1, + .activate = 8 + } +}; + +/* proprietary request/response format */ +struct scarlett2_usb_packet { + u32 cmd; + u16 size; + u16 seq; + u32 error; + u32 pad; + u8 data[]; +}; + +#define SCARLETT2_USB_PACKET_LEN (sizeof(struct scarlett2_usb_packet)) + +static void scarlett2_fill_request_header(struct scarlett2_mixer_data *private, + struct scarlett2_usb_packet *req, + u32 cmd, u16 req_size) +{ + /* sequence must go up by 1 for each request */ + u16 seq = private->scarlett2_seq++; + + req->cmd = cpu_to_le32(cmd); + req->size = cpu_to_le16(req_size); + req->seq = cpu_to_le16(seq); + req->error = 0; + req->pad = 0; +} + +/* Send a proprietary format request to the Scarlett interface */ +static int scarlett2_usb( + struct usb_mixer_interface *mixer, u32 cmd, + void *req_data, u16 req_size, void *resp_data, u16 resp_size) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + u16 req_buf_size = sizeof(struct scarlett2_usb_packet) + req_size; + u16 resp_buf_size = sizeof(struct scarlett2_usb_packet) + resp_size; + struct scarlett2_usb_packet *req = NULL, *resp = NULL; + int err = 0; + + req = kmalloc(req_buf_size, GFP_KERNEL); + if (!req) { + err = -ENOMEM; + goto error; + } + + resp = kmalloc(resp_buf_size, GFP_KERNEL); + if (!resp) { + err = -ENOMEM; + goto error; + } + + mutex_lock(&private->usb_mutex); + + /* build request message and send it */ + + scarlett2_fill_request_header(private, req, cmd, req_size); + + if (req_size) + memcpy(req->data, req_data, req_size); + + err = snd_usb_ctl_msg(mixer->chip->dev, + usb_sndctrlpipe(mixer->chip->dev, 0), + SCARLETT2_USB_VENDOR_SPECIFIC_CMD_REQ, + USB_RECIP_INTERFACE | USB_TYPE_CLASS | USB_DIR_OUT, + 0, + SCARLETT2_USB_VENDOR_SPECIFIC_INTERFACE, + req, + req_buf_size); + + if (err != req_buf_size) { + usb_audio_err( + mixer->chip, + "Scarlett Gen 2 USB request result cmd %x was %d\n", + cmd, err); + err = -EINVAL; + goto unlock; + } + + /* send a second message to get the response */ + + err = snd_usb_ctl_msg(mixer->chip->dev, + usb_sndctrlpipe(mixer->chip->dev, 0), + SCARLETT2_USB_VENDOR_SPECIFIC_CMD_RESP, + USB_RECIP_INTERFACE | USB_TYPE_CLASS | USB_DIR_IN, + 0, + SCARLETT2_USB_VENDOR_SPECIFIC_INTERFACE, + resp, + resp_buf_size); + + /* validate the response */ + + if (err != resp_buf_size) { + usb_audio_err( + mixer->chip, + "Scarlett Gen 2 USB response result cmd %x was %d\n", + cmd, err); + err = -EINVAL; + goto unlock; + } + + if (resp->cmd != req->cmd || + resp->seq != req->seq || + resp_size != le16_to_cpu(resp->size) || + resp->error || + resp->pad) { + usb_audio_err( + mixer->chip, + "Scarlett Gen 2 USB invalid response; " + "cmd tx/rx %d/%d seq %d/%d size %d/%d " + "error %d pad %d\n", + le16_to_cpu(req->cmd), le16_to_cpu(resp->cmd), + le16_to_cpu(req->seq), le16_to_cpu(resp->seq), + resp_size, le16_to_cpu(resp->size), + le16_to_cpu(resp->error), + le16_to_cpu(resp->pad)); + err = -EINVAL; + goto unlock; + } + + if (resp_size > 0) + memcpy(resp_data, resp->data, resp_size); + +unlock: + mutex_unlock(&private->usb_mutex); +error: + kfree(req); + kfree(resp); + return err; +} + +/* Send SCARLETT2_USB_DATA_CMD SCARLETT2_USB_CONFIG_SAVE */ +static void scarlett2_config_save(struct usb_mixer_interface *mixer) +{ + u32 req = cpu_to_le32(SCARLETT2_USB_CONFIG_SAVE); + + scarlett2_usb(mixer, SCARLETT2_USB_DATA_CMD, + &req, sizeof(u32), + NULL, 0); +} + +/* Delayed work to save config */ +static void scarlett2_config_save_work(struct work_struct *work) +{ + struct scarlett2_mixer_data *private = + container_of(work, struct scarlett2_mixer_data, work.work); + + scarlett2_config_save(private->mixer); +} + +/* Send a USB message to set a configuration parameter (volume level, + * sw/hw volume switch, line/inst level switch, or pad switch) + */ +static int scarlett2_usb_set_config( + struct usb_mixer_interface *mixer, + int config_item_num, int index, int value) +{ + const struct scarlett2_config config_item = + scarlett2_config_items[config_item_num]; + struct { + u32 offset; + u32 bytes; + s32 value; + } __packed req; + u32 req2; + int err; + struct scarlett2_mixer_data *private = mixer->private_data; + + /* Cancel any pending NVRAM save */ + cancel_delayed_work_sync(&private->work); + + /* Send the configuration parameter data */ + req.offset = cpu_to_le32(config_item.offset + index * config_item.size); + req.bytes = cpu_to_le32(config_item.size); + req.value = cpu_to_le32(value); + err = scarlett2_usb(mixer, SCARLETT2_USB_SET_DATA, + &req, sizeof(u32) * 2 + config_item.size, + NULL, 0); + if (err < 0) + return err; + + /* Activate the change */ + req2 = cpu_to_le32(config_item.activate); + err = scarlett2_usb(mixer, SCARLETT2_USB_DATA_CMD, + &req2, sizeof(req2), NULL, 0); + if (err < 0) + return err; + + /* Schedule the change to be written to NVRAM */ + schedule_delayed_work(&private->work, msecs_to_jiffies(2000)); + + return 0; +} + +/* Send a USB message to get data; result placed in *buf */ +static int scarlett2_usb_get( + struct usb_mixer_interface *mixer, + int offset, void *buf, int size) +{ + struct { + u32 offset; + u32 size; + } __packed req; + + req.offset = cpu_to_le32(offset); + req.size = cpu_to_le32(size); + return scarlett2_usb(mixer, SCARLETT2_USB_GET_DATA, + &req, sizeof(req), buf, size); +} + +/* Send a USB message to get configuration parameters; result placed in *buf */ +static int scarlett2_usb_get_config( + struct usb_mixer_interface *mixer, + int config_item_num, int count, void *buf) +{ + const struct scarlett2_config config_item = + scarlett2_config_items[config_item_num]; + int size = config_item.size * count; + + return scarlett2_usb_get(mixer, config_item.offset, buf, size); +} + +/* Send a USB message to get volume status; result placed in *buf */ +static int scarlett2_usb_get_volume_status( + struct usb_mixer_interface *mixer, + struct scarlett2_usb_volume_status *buf) +{ + return scarlett2_usb_get(mixer, SCARLETT2_USB_VOLUME_STATUS_OFFSET, + buf, sizeof(*buf)); +} + +/* Send a USB message to set the volumes for all inputs of one mix + * (values obtained from private->mix[]) + */ +static int scarlett2_usb_set_mix(struct usb_mixer_interface *mixer, + int mix_num) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_device_info *info = private->info; + + struct { + u16 mix_num; + u16 data[SCARLETT2_INPUT_MIX_MAX]; + } __packed req; + + int i, j; + int num_mixer_in = + info->ports[SCARLETT2_PORT_TYPE_MIX].num[SCARLETT2_PORT_OUT]; + + req.mix_num = cpu_to_le16(mix_num); + + for (i = 0, j = mix_num * num_mixer_in; i < num_mixer_in; i++, j++) + req.data[i] = cpu_to_le16( + scarlett2_mixer_values[private->mix[j]] + ); + + return scarlett2_usb(mixer, SCARLETT2_USB_SET_MIX, + &req, (num_mixer_in + 1) * sizeof(u16), + NULL, 0); +} + +/* Convert a port number index (per info->ports) to a hardware ID */ +static u32 scarlett2_mux_src_num_to_id(const struct scarlett2_ports *ports, + int num) +{ + int port_type; + + for (port_type = 0; + port_type < SCARLETT2_PORT_TYPE_COUNT; + port_type++) { + if (num < ports[port_type].num[SCARLETT2_PORT_IN]) + return ports[port_type].id | num; + num -= ports[port_type].num[SCARLETT2_PORT_IN]; + } + + /* Oops */ + return 0; +} + +/* Send USB messages to set mux inputs */ +static int scarlett2_usb_set_mux(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_device_info *info = private->info; + const struct scarlett2_ports *ports = info->ports; + int rate, port_dir_rate; + + static const int assignment_order[SCARLETT2_PORT_TYPE_COUNT] = { + SCARLETT2_PORT_TYPE_PCM, + SCARLETT2_PORT_TYPE_ANALOGUE, + SCARLETT2_PORT_TYPE_SPDIF, + SCARLETT2_PORT_TYPE_ADAT, + SCARLETT2_PORT_TYPE_MIX, + SCARLETT2_PORT_TYPE_NONE, + }; + + struct { + u16 pad; + u16 num; + u32 data[SCARLETT2_MUX_MAX]; + } __packed req; + + req.pad = 0; + + /* mux settings for each rate */ + for (rate = 0, port_dir_rate = SCARLETT2_PORT_OUT_44; + port_dir_rate <= SCARLETT2_PORT_OUT_176; + rate++, port_dir_rate++) { + int order_num, i, err; + + req.num = cpu_to_le16(rate); + + for (order_num = 0, i = 0; + order_num < SCARLETT2_PORT_TYPE_COUNT; + order_num++) { + int port_type = assignment_order[order_num]; + int j = scarlett2_get_port_start_num(ports, + SCARLETT2_PORT_OUT, + port_type); + int port_id = ports[port_type].id; + int channel; + + for (channel = 0; + channel < ports[port_type].num[port_dir_rate]; + channel++, i++, j++) + /* lower 12 bits for the destination and + * next 12 bits for the source + */ + req.data[i] = !port_id + ? 0 + : cpu_to_le32( + port_id | + channel | + scarlett2_mux_src_num_to_id( + ports, private->mux[j] + ) << 12 + ); + + /* skip private->mux[j] entries not output */ + j += ports[port_type].num[SCARLETT2_PORT_OUT] - + ports[port_type].num[port_dir_rate]; + } + + err = scarlett2_usb(mixer, SCARLETT2_USB_SET_MUX, + &req, (i + 1) * sizeof(u32), + NULL, 0); + if (err < 0) + return err; + } + + return 0; +} + +/* Send USB message to get meter levels */ +static int scarlett2_usb_get_meter_levels(struct usb_mixer_interface *mixer, + u16 *levels) +{ + struct { + u16 pad; + u16 num_meters; + u32 magic; + } __packed req; + u32 resp[SCARLETT2_NUM_METERS]; + int i, err; + + req.pad = 0; + req.num_meters = cpu_to_le16(SCARLETT2_NUM_METERS); + req.magic = cpu_to_le32(SCARLETT2_USB_METER_LEVELS_GET_MAGIC); + err = scarlett2_usb(mixer, SCARLETT2_USB_GET_METER_LEVELS, + &req, sizeof(req), resp, sizeof(resp)); + if (err < 0) + return err; + + /* copy, convert to u16 */ + for (i = 0; i < SCARLETT2_NUM_METERS; i++) + levels[i] = resp[i]; + + return 0; +} + +/*** Control Functions ***/ + +/* helper function to create a new control */ +static int scarlett2_add_new_ctl(struct usb_mixer_interface *mixer, + const struct snd_kcontrol_new *ncontrol, + int index, int channels, const char *name, + struct snd_kcontrol **kctl_return) +{ + struct snd_kcontrol *kctl; + struct usb_mixer_elem_info *elem; + int err; + + elem = kzalloc(sizeof(*elem), GFP_KERNEL); + if (!elem) + return -ENOMEM; + + elem->head.mixer = mixer; + elem->control = index; + elem->head.id = index; + elem->channels = channels; + + kctl = snd_ctl_new1(ncontrol, elem); + if (!kctl) { + kfree(elem); + return -ENOMEM; + } + kctl->private_free = snd_usb_mixer_elem_free; + + strlcpy(kctl->id.name, name, sizeof(kctl->id.name)); + + err = snd_usb_mixer_add_control(&elem->head, kctl); + if (err < 0) + return err; + + if (kctl_return) + *kctl_return = kctl; + + return 0; +} + +/*** Analogue Line Out Volume Controls ***/ + +/* Update hardware volume controls after receiving notification that + * they have changed + */ +static int scarlett2_update_volumes(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_ports *ports = private->info->ports; + struct scarlett2_usb_volume_status volume_status; + int num_line_out = + ports[SCARLETT2_PORT_TYPE_ANALOGUE].num[SCARLETT2_PORT_OUT]; + int err, i; + + private->vol_updated = 0; + + err = scarlett2_usb_get_volume_status(mixer, &volume_status); + if (err < 0) + return err; + + private->master_vol = clamp( + volume_status.master_vol + SCARLETT2_VOLUME_BIAS, + 0, SCARLETT2_VOLUME_BIAS); + + for (i = 0; i < num_line_out; i++) { + if (private->vol_sw_hw_switch[i]) + private->vol[i] = private->master_vol; + } + + for (i = 0; i < private->info->button_count; i++) + private->buttons[i] = !!volume_status.buttons[i]; + + return 0; +} + +static int scarlett2_volume_ctl_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = elem->channels; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = SCARLETT2_VOLUME_BIAS; + uinfo->value.integer.step = 1; + return 0; +} + +static int scarlett2_master_volume_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + + if (private->vol_updated) { + mutex_lock(&private->data_mutex); + scarlett2_update_volumes(mixer); + mutex_unlock(&private->data_mutex); + } + + ucontrol->value.integer.value[0] = private->master_vol; + return 0; +} + +static int scarlett2_volume_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + int index = elem->control; + + if (private->vol_updated) { + mutex_lock(&private->data_mutex); + scarlett2_update_volumes(mixer); + mutex_unlock(&private->data_mutex); + } + + ucontrol->value.integer.value[0] = private->vol[index]; + return 0; +} + +static int scarlett2_volume_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + int index = elem->control; + int oval, val, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->vol[index]; + val = ucontrol->value.integer.value[0]; + + if (oval == val) + goto unlock; + + private->vol[index] = val; + err = scarlett2_usb_set_config(mixer, SCARLETT2_CONFIG_LINE_OUT_VOLUME, + index, val - SCARLETT2_VOLUME_BIAS); + if (err == 0) + err = 1; + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const DECLARE_TLV_DB_MINMAX( + db_scale_scarlett2_gain, -SCARLETT2_VOLUME_BIAS * 100, 0 +); + +static const struct snd_kcontrol_new scarlett2_master_volume_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .access = SNDRV_CTL_ELEM_ACCESS_READ | + SNDRV_CTL_ELEM_ACCESS_TLV_READ, + .name = "", + .info = scarlett2_volume_ctl_info, + .get = scarlett2_master_volume_ctl_get, + .private_value = 0, /* max value */ + .tlv = { .p = db_scale_scarlett2_gain } +}; + +static const struct snd_kcontrol_new scarlett2_line_out_volume_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .access = SNDRV_CTL_ELEM_ACCESS_READWRITE | + SNDRV_CTL_ELEM_ACCESS_TLV_READ, + .name = "", + .info = scarlett2_volume_ctl_info, + .get = scarlett2_volume_ctl_get, + .put = scarlett2_volume_ctl_put, + .private_value = 0, /* max value */ + .tlv = { .p = db_scale_scarlett2_gain } +}; + +/*** HW/SW Volume Switch Controls ***/ + +static int scarlett2_sw_hw_enum_ctl_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + static const char *const values[2] = { + "SW", "HW" + }; + + return snd_ctl_enum_info(uinfo, 1, 2, values); +} + +static int scarlett2_sw_hw_enum_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct scarlett2_mixer_data *private = elem->head.mixer->private_data; + + ucontrol->value.enumerated.item[0] = + private->vol_sw_hw_switch[elem->control]; + return 0; +} + +static int scarlett2_sw_hw_enum_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + + int index = elem->control; + int oval, val, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->vol_sw_hw_switch[index]; + val = !!ucontrol->value.integer.value[0]; + + if (oval == val) + goto unlock; + + private->vol_sw_hw_switch[index] = val; + + /* Change access mode to RO (hardware controlled volume) + * or RW (software controlled volume) + */ + if (val) + private->vol_ctls[index]->vd[0].access &= + ~SNDRV_CTL_ELEM_ACCESS_WRITE; + else + private->vol_ctls[index]->vd[0].access |= + SNDRV_CTL_ELEM_ACCESS_WRITE; + + /* Reset volume to master volume */ + private->vol[index] = private->master_vol; + + /* Set SW volume to current HW volume */ + err = scarlett2_usb_set_config( + mixer, SCARLETT2_CONFIG_LINE_OUT_VOLUME, + index, private->master_vol - SCARLETT2_VOLUME_BIAS); + if (err < 0) + goto unlock; + + /* Notify of RO/RW change */ + snd_ctl_notify(mixer->chip->card, SNDRV_CTL_EVENT_MASK_INFO, + &private->vol_ctls[index]->id); + + /* Send SW/HW switch change to the device */ + err = scarlett2_usb_set_config(mixer, SCARLETT2_CONFIG_SW_HW_SWITCH, + index, val); + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const struct snd_kcontrol_new scarlett2_sw_hw_enum_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "", + .info = scarlett2_sw_hw_enum_ctl_info, + .get = scarlett2_sw_hw_enum_ctl_get, + .put = scarlett2_sw_hw_enum_ctl_put, +}; + +/*** Line Level/Instrument Level Switch Controls ***/ + +static int scarlett2_level_enum_ctl_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + static const char *const values[2] = { + "Line", "Inst" + }; + + return snd_ctl_enum_info(uinfo, 1, 2, values); +} + +static int scarlett2_level_enum_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct scarlett2_mixer_data *private = elem->head.mixer->private_data; + + ucontrol->value.enumerated.item[0] = + private->level_switch[elem->control]; + return 0; +} + +static int scarlett2_level_enum_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + + int index = elem->control; + int oval, val, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->level_switch[index]; + val = !!ucontrol->value.integer.value[0]; + + if (oval == val) + goto unlock; + + private->level_switch[index] = val; + + /* Send switch change to the device */ + err = scarlett2_usb_set_config(mixer, SCARLETT2_CONFIG_LEVEL_SWITCH, + index, val); + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const struct snd_kcontrol_new scarlett2_level_enum_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "", + .info = scarlett2_level_enum_ctl_info, + .get = scarlett2_level_enum_ctl_get, + .put = scarlett2_level_enum_ctl_put, +}; + +/*** Pad Switch Controls ***/ + +static int scarlett2_pad_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct scarlett2_mixer_data *private = elem->head.mixer->private_data; + + ucontrol->value.enumerated.item[0] = + private->pad_switch[elem->control]; + return 0; +} + +static int scarlett2_pad_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + + int index = elem->control; + int oval, val, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->pad_switch[index]; + val = !!ucontrol->value.integer.value[0]; + + if (oval == val) + goto unlock; + + private->pad_switch[index] = val; + + /* Send switch change to the device */ + err = scarlett2_usb_set_config(mixer, SCARLETT2_CONFIG_PAD_SWITCH, + index, val); + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const struct snd_kcontrol_new scarlett2_pad_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "", + .info = snd_ctl_boolean_mono_info, + .get = scarlett2_pad_ctl_get, + .put = scarlett2_pad_ctl_put, +}; + +/*** Mute/Dim Controls ***/ + +static int scarlett2_button_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + + if (private->vol_updated) { + mutex_lock(&private->data_mutex); + scarlett2_update_volumes(mixer); + mutex_unlock(&private->data_mutex); + } + + ucontrol->value.enumerated.item[0] = private->buttons[elem->control]; + return 0; +} + +static int scarlett2_button_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + + int index = elem->control; + int oval, val, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->buttons[index]; + val = !!ucontrol->value.integer.value[0]; + + if (oval == val) + goto unlock; + + private->buttons[index] = val; + + /* Send switch change to the device */ + err = scarlett2_usb_set_config(mixer, SCARLETT2_CONFIG_BUTTONS, + index, val); + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const struct snd_kcontrol_new scarlett2_button_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "", + .info = snd_ctl_boolean_mono_info, + .get = scarlett2_button_ctl_get, + .put = scarlett2_button_ctl_put +}; + +/*** Create the analogue output controls ***/ + +static int scarlett2_add_line_out_ctls(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_device_info *info = private->info; + const struct scarlett2_ports *ports = info->ports; + int num_line_out = + ports[SCARLETT2_PORT_TYPE_ANALOGUE].num[SCARLETT2_PORT_OUT]; + int err, i; + char s[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + + /* Add R/O HW volume control */ + if (info->line_out_hw_vol) { + snprintf(s, sizeof(s), "Master HW Playback Volume"); + err = scarlett2_add_new_ctl(mixer, + &scarlett2_master_volume_ctl, + 0, 1, s, &private->master_vol_ctl); + if (err < 0) + return err; + } + + /* Add volume controls */ + for (i = 0; i < num_line_out; i++) { + + /* Fader */ + if (info->line_out_descrs[i]) + snprintf(s, sizeof(s), + "Line %02d (%s) Playback Volume", + i + 1, info->line_out_descrs[i]); + else + snprintf(s, sizeof(s), + "Line %02d Playback Volume", + i + 1); + err = scarlett2_add_new_ctl(mixer, + &scarlett2_line_out_volume_ctl, + i, 1, s, &private->vol_ctls[i]); + if (err < 0) + return err; + + /* Make the fader read-only if the SW/HW switch is set to HW */ + if (private->vol_sw_hw_switch[i]) + private->vol_ctls[i]->vd[0].access &= + ~SNDRV_CTL_ELEM_ACCESS_WRITE; + + /* SW/HW Switch */ + if (info->line_out_hw_vol) { + snprintf(s, sizeof(s), + "Line Out %02d Volume Control Playback Enum", + i + 1); + err = scarlett2_add_new_ctl(mixer, + &scarlett2_sw_hw_enum_ctl, + i, 1, s, NULL); + if (err < 0) + return err; + } + } + + /* Add HW button controls */ + for (i = 0; i < private->info->button_count; i++) { + err = scarlett2_add_new_ctl(mixer, &scarlett2_button_ctl, + i, 1, scarlett2_button_names[i], + &private->button_ctls[i]); + if (err < 0) + return err; + } + + return 0; +} + +/*** Create the analogue input controls ***/ + +static int scarlett2_add_line_in_ctls(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_device_info *info = private->info; + int err, i; + char s[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + + /* Add input level (line/inst) controls */ + for (i = 0; i < info->level_input_count; i++) { + snprintf(s, sizeof(s), "Line In %d Level Capture Enum", i + 1); + err = scarlett2_add_new_ctl(mixer, &scarlett2_level_enum_ctl, + i, 1, s, NULL); + if (err < 0) + return err; + } + + /* Add input pad controls */ + for (i = 0; i < info->pad_input_count; i++) { + snprintf(s, sizeof(s), "Line In %d Pad Capture Switch", i + 1); + err = scarlett2_add_new_ctl(mixer, &scarlett2_pad_ctl, + i, 1, s, NULL); + if (err < 0) + return err; + } + + return 0; +} + +/*** Mixer Volume Controls ***/ + +static int scarlett2_mixer_ctl_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = elem->channels; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = SCARLETT2_MIXER_MAX_VALUE; + uinfo->value.integer.step = 1; + return 0; +} + +static int scarlett2_mixer_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct scarlett2_mixer_data *private = elem->head.mixer->private_data; + + ucontrol->value.integer.value[0] = private->mix[elem->control]; + return 0; +} + +static int scarlett2_mixer_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_device_info *info = private->info; + const struct scarlett2_ports *ports = info->ports; + int oval, val, num_mixer_in, mix_num, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->mix[elem->control]; + val = ucontrol->value.integer.value[0]; + num_mixer_in = ports[SCARLETT2_PORT_TYPE_MIX].num[SCARLETT2_PORT_OUT]; + mix_num = elem->control / num_mixer_in; + + if (oval == val) + goto unlock; + + private->mix[elem->control] = val; + err = scarlett2_usb_set_mix(mixer, mix_num); + if (err == 0) + err = 1; + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const DECLARE_TLV_DB_MINMAX( + db_scale_scarlett2_mixer, + SCARLETT2_MIXER_MIN_DB * 100, + SCARLETT2_MIXER_MAX_DB * 100 +); + +static const struct snd_kcontrol_new scarlett2_mixer_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .access = SNDRV_CTL_ELEM_ACCESS_READWRITE | + SNDRV_CTL_ELEM_ACCESS_TLV_READ, + .name = "", + .info = scarlett2_mixer_ctl_info, + .get = scarlett2_mixer_ctl_get, + .put = scarlett2_mixer_ctl_put, + .private_value = SCARLETT2_MIXER_MAX_DB, /* max value */ + .tlv = { .p = db_scale_scarlett2_mixer } +}; + +static int scarlett2_add_mixer_ctls(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_ports *ports = private->info->ports; + int err, i, j; + int index; + char s[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + + int num_inputs = ports[SCARLETT2_PORT_TYPE_MIX].num[SCARLETT2_PORT_OUT]; + int num_outputs = ports[SCARLETT2_PORT_TYPE_MIX].num[SCARLETT2_PORT_IN]; + + for (i = 0, index = 0; i < num_outputs; i++) { + for (j = 0; j < num_inputs; j++, index++) { + snprintf(s, sizeof(s), + "Mix %c Input %02d Playback Volume", + 'A' + i, j + 1); + err = scarlett2_add_new_ctl(mixer, &scarlett2_mixer_ctl, + index, 1, s, NULL); + if (err < 0) + return err; + } + } + + return 0; +} + +/*** Mux Source Selection Controls ***/ + +static int scarlett2_mux_src_enum_ctl_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct scarlett2_mixer_data *private = elem->head.mixer->private_data; + const struct scarlett2_ports *ports = private->info->ports; + unsigned int item = uinfo->value.enumerated.item; + int items = private->num_mux_srcs; + int port_type; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_ENUMERATED; + uinfo->count = elem->channels; + uinfo->value.enumerated.items = items; + + if (item >= items) + item = uinfo->value.enumerated.item = items - 1; + + for (port_type = 0; + port_type < SCARLETT2_PORT_TYPE_COUNT; + port_type++) { + if (item < ports[port_type].num[SCARLETT2_PORT_IN]) { + sprintf(uinfo->value.enumerated.name, + ports[port_type].src_descr, + item + ports[port_type].src_num_offset); + return 0; + } + item -= ports[port_type].num[SCARLETT2_PORT_IN]; + } + + return -EINVAL; +} + +static int scarlett2_mux_src_enum_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct scarlett2_mixer_data *private = elem->head.mixer->private_data; + + ucontrol->value.enumerated.item[0] = private->mux[elem->control]; + return 0; +} + +static int scarlett2_mux_src_enum_ctl_put(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + struct usb_mixer_interface *mixer = elem->head.mixer; + struct scarlett2_mixer_data *private = mixer->private_data; + int index = elem->control; + int oval, val, err = 0; + + mutex_lock(&private->data_mutex); + + oval = private->mux[index]; + val = clamp(ucontrol->value.integer.value[0], + 0L, private->num_mux_srcs - 1L); + + if (oval == val) + goto unlock; + + private->mux[index] = val; + err = scarlett2_usb_set_mux(mixer); + if (err == 0) + err = 1; + +unlock: + mutex_unlock(&private->data_mutex); + return err; +} + +static const struct snd_kcontrol_new scarlett2_mux_src_enum_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_MIXER, + .name = "", + .info = scarlett2_mux_src_enum_ctl_info, + .get = scarlett2_mux_src_enum_ctl_get, + .put = scarlett2_mux_src_enum_ctl_put, +}; + +static int scarlett2_add_mux_enums(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_ports *ports = private->info->ports; + int port_type, channel, i; + + for (i = 0, port_type = 0; + port_type < SCARLETT2_PORT_TYPE_COUNT; + port_type++) { + for (channel = 0; + channel < ports[port_type].num[SCARLETT2_PORT_OUT]; + channel++, i++) { + int err; + char s[SNDRV_CTL_ELEM_ID_NAME_MAXLEN]; + const char *const descr = ports[port_type].dst_descr; + + snprintf(s, sizeof(s) - 5, descr, channel + 1); + strcat(s, " Enum"); + + err = scarlett2_add_new_ctl(mixer, + &scarlett2_mux_src_enum_ctl, + i, 1, s, NULL); + if (err < 0) + return err; + } + } + + return 0; +} + +/*** Meter Controls ***/ + +static int scarlett2_meter_ctl_info(struct snd_kcontrol *kctl, + struct snd_ctl_elem_info *uinfo) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = elem->channels; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = 4095; + uinfo->value.integer.step = 1; + return 0; +} + +static int scarlett2_meter_ctl_get(struct snd_kcontrol *kctl, + struct snd_ctl_elem_value *ucontrol) +{ + struct usb_mixer_elem_info *elem = kctl->private_data; + u16 meter_levels[SCARLETT2_NUM_METERS]; + int i, err; + + err = scarlett2_usb_get_meter_levels(elem->head.mixer, meter_levels); + if (err < 0) + return err; + + for (i = 0; i < elem->channels; i++) + ucontrol->value.integer.value[i] = meter_levels[i]; + + return 0; +} + +static const struct snd_kcontrol_new scarlett2_meter_ctl = { + .iface = SNDRV_CTL_ELEM_IFACE_PCM, + .access = SNDRV_CTL_ELEM_ACCESS_READ | SNDRV_CTL_ELEM_ACCESS_VOLATILE, + .name = "", + .info = scarlett2_meter_ctl_info, + .get = scarlett2_meter_ctl_get +}; + +static int scarlett2_add_meter_ctl(struct usb_mixer_interface *mixer) +{ + return scarlett2_add_new_ctl(mixer, &scarlett2_meter_ctl, + 0, SCARLETT2_NUM_METERS, + "Level Meter", NULL); +} + +/*** Cleanup/Suspend Callbacks ***/ + +static void scarlett2_private_free(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + + cancel_delayed_work_sync(&private->work); + kfree(private); + mixer->private_data = NULL; +} + +static void scarlett2_private_suspend(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + + if (cancel_delayed_work_sync(&private->work)) + scarlett2_config_save(private->mixer); +} + +/*** Initialisation ***/ + +static int scarlett2_count_mux_srcs(const struct scarlett2_ports *ports) +{ + int port_type, count = 0; + + for (port_type = 0; + port_type < SCARLETT2_PORT_TYPE_COUNT; + port_type++) + count += ports[port_type].num[SCARLETT2_PORT_IN]; + + return count; +} + +/* Default routing connects PCM outputs and inputs to Analogue, + * S/PDIF, then ADAT + */ +static void scarlett2_init_routing(u8 *mux, + const struct scarlett2_ports *ports) +{ + int i, input_num, input_count, port_type; + int output_num, output_count, port_type_connect_num; + + static const int connect_order[] = { + SCARLETT2_PORT_TYPE_ANALOGUE, + SCARLETT2_PORT_TYPE_SPDIF, + SCARLETT2_PORT_TYPE_ADAT, + -1 + }; + + /* Assign PCM inputs (routing outputs) */ + output_num = scarlett2_get_port_start_num(ports, + SCARLETT2_PORT_OUT, + SCARLETT2_PORT_TYPE_PCM); + output_count = ports[SCARLETT2_PORT_TYPE_PCM].num[SCARLETT2_PORT_OUT]; + + for (port_type = connect_order[port_type_connect_num = 0]; + port_type >= 0; + port_type = connect_order[++port_type_connect_num]) { + input_num = scarlett2_get_port_start_num( + ports, SCARLETT2_PORT_IN, port_type); + input_count = ports[port_type].num[SCARLETT2_PORT_IN]; + for (i = 0; + i < input_count && output_count; + i++, output_count--) + mux[output_num++] = input_num++; + } + + /* Assign PCM outputs (routing inputs) */ + input_num = scarlett2_get_port_start_num(ports, + SCARLETT2_PORT_IN, + SCARLETT2_PORT_TYPE_PCM); + input_count = ports[SCARLETT2_PORT_TYPE_PCM].num[SCARLETT2_PORT_IN]; + + for (port_type = connect_order[port_type_connect_num = 0]; + port_type >= 0; + port_type = connect_order[++port_type_connect_num]) { + output_num = scarlett2_get_port_start_num( + ports, SCARLETT2_PORT_OUT, port_type); + output_count = ports[port_type].num[SCARLETT2_PORT_OUT]; + for (i = 0; + i < output_count && input_count; + i++, input_count--) + mux[output_num++] = input_num++; + } +} + +/* Initialise private data, routing, sequence number */ +static int scarlett2_init_private(struct usb_mixer_interface *mixer, + const struct scarlett2_device_info *info) +{ + struct scarlett2_mixer_data *private = + kzalloc(sizeof(struct scarlett2_mixer_data), GFP_KERNEL); + + if (!private) + return -ENOMEM; + + mutex_init(&private->usb_mutex); + mutex_init(&private->data_mutex); + INIT_DELAYED_WORK(&private->work, scarlett2_config_save_work); + private->info = info; + private->num_mux_srcs = scarlett2_count_mux_srcs(info->ports); + private->scarlett2_seq = 0; + private->mixer = mixer; + mixer->private_data = private; + mixer->private_free = scarlett2_private_free; + mixer->private_suspend = scarlett2_private_suspend; + + /* Setup default routing */ + scarlett2_init_routing(private->mux, info->ports); + + /* Initialise the sequence number used for the proprietary commands */ + return scarlett2_usb(mixer, SCARLETT2_USB_INIT_SEQ, NULL, 0, NULL, 0); +} + +/* Read line-in config and line-out volume settings on start */ +static int scarlett2_read_configs(struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_device_info *info = private->info; + const struct scarlett2_ports *ports = info->ports; + int num_line_out = + ports[SCARLETT2_PORT_TYPE_ANALOGUE].num[SCARLETT2_PORT_OUT]; + u8 level_switches[SCARLETT2_LEVEL_SWITCH_MAX]; + u8 pad_switches[SCARLETT2_PAD_SWITCH_MAX]; + struct scarlett2_usb_volume_status volume_status; + int err, i; + + if (info->level_input_count) { + err = scarlett2_usb_get_config( + mixer, + SCARLETT2_CONFIG_LEVEL_SWITCH, + info->level_input_count, + level_switches); + if (err < 0) + return err; + for (i = 0; i < info->level_input_count; i++) + private->level_switch[i] = level_switches[i]; + } + + if (info->pad_input_count) { + err = scarlett2_usb_get_config( + mixer, + SCARLETT2_CONFIG_PAD_SWITCH, + info->pad_input_count, + pad_switches); + if (err < 0) + return err; + for (i = 0; i < info->pad_input_count; i++) + private->pad_switch[i] = pad_switches[i]; + } + + err = scarlett2_usb_get_volume_status(mixer, &volume_status); + if (err < 0) + return err; + + private->master_vol = clamp( + volume_status.master_vol + SCARLETT2_VOLUME_BIAS, + 0, SCARLETT2_VOLUME_BIAS); + + for (i = 0; i < num_line_out; i++) { + int volume; + + private->vol_sw_hw_switch[i] = + info->line_out_hw_vol + && volume_status.sw_hw_switch[i]; + + volume = private->vol_sw_hw_switch[i] + ? volume_status.master_vol + : volume_status.sw_vol[i]; + volume = clamp(volume + SCARLETT2_VOLUME_BIAS, + 0, SCARLETT2_VOLUME_BIAS); + private->vol[i] = volume; + } + + for (i = 0; i < info->button_count; i++) + private->buttons[i] = !!volume_status.buttons[i]; + + return 0; +} + +/* Notify on volume change */ +static void scarlett2_mixer_interrupt_vol_change( + struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + const struct scarlett2_ports *ports = private->info->ports; + int num_line_out = + ports[SCARLETT2_PORT_TYPE_ANALOGUE].num[SCARLETT2_PORT_OUT]; + int i; + + private->vol_updated = 1; + + snd_ctl_notify(mixer->chip->card, SNDRV_CTL_EVENT_MASK_VALUE, + &private->master_vol_ctl->id); + + for (i = 0; i < num_line_out; i++) { + if (!private->vol_sw_hw_switch[i]) + continue; + snd_ctl_notify(mixer->chip->card, SNDRV_CTL_EVENT_MASK_VALUE, + &private->vol_ctls[i]->id); + } +} + +/* Notify on button change */ +static void scarlett2_mixer_interrupt_button_change( + struct usb_mixer_interface *mixer) +{ + struct scarlett2_mixer_data *private = mixer->private_data; + int i; + + private->vol_updated = 1; + + for (i = 0; i < private->info->button_count; i++) + snd_ctl_notify(mixer->chip->card, SNDRV_CTL_EVENT_MASK_VALUE, + &private->button_ctls[i]->id); +} + +/* Interrupt callback */ +static void scarlett2_mixer_interrupt(struct urb *urb) +{ + struct usb_mixer_interface *mixer = urb->context; + int len = urb->actual_length; + int ustatus = urb->status; + u32 data; + + if (ustatus != 0) + goto requeue; + + if (len == 8) { + data = le32_to_cpu(*(u32 *)urb->transfer_buffer); + if (data & SCARLETT2_USB_INTERRUPT_VOL_CHANGE) + scarlett2_mixer_interrupt_vol_change(mixer); + if (data & SCARLETT2_USB_INTERRUPT_BUTTON_CHANGE) + scarlett2_mixer_interrupt_button_change(mixer); + } else { + usb_audio_err(mixer->chip, + "scarlett mixer interrupt length %d\n", len); + } + +requeue: + if (ustatus != -ENOENT && + ustatus != -ECONNRESET && + ustatus != -ESHUTDOWN) { + urb->dev = mixer->chip->dev; + usb_submit_urb(urb, GFP_ATOMIC); + } +} + +static int scarlett2_mixer_status_create(struct usb_mixer_interface *mixer) +{ + struct usb_device *dev = mixer->chip->dev; + unsigned int pipe = usb_rcvintpipe(dev, + SCARLETT2_USB_INTERRUPT_ENDPOINT); + void *transfer_buffer; + + if (mixer->urb) { + usb_audio_err(mixer->chip, + "%s: mixer urb already in use!\n", __func__); + return 0; + } + + if (snd_usb_pipe_sanity_check(dev, pipe)) + return -EINVAL; + + mixer->urb = usb_alloc_urb(0, GFP_KERNEL); + if (!mixer->urb) + return -ENOMEM; + + transfer_buffer = kmalloc(SCARLETT2_USB_INTERRUPT_MAX_DATA, GFP_KERNEL); + if (!transfer_buffer) + return -ENOMEM; + + usb_fill_int_urb(mixer->urb, dev, pipe, + transfer_buffer, SCARLETT2_USB_INTERRUPT_MAX_DATA, + scarlett2_mixer_interrupt, mixer, + SCARLETT2_USB_INTERRUPT_INTERVAL); + + return usb_submit_urb(mixer->urb, GFP_KERNEL); +} + +/* Entry point */ +int snd_scarlett_gen2_controls_create(struct usb_mixer_interface *mixer) +{ + const struct scarlett2_device_info *info; + int err; + + /* only use UAC_VERSION_2 */ + if (!mixer->protocol) + return 0; + + switch (mixer->chip->usb_id) { + case USB_ID(0x1235, 0x8203): + info = &s6i6_gen2_info; + break; + case USB_ID(0x1235, 0x8204): + info = &s18i8_gen2_info; + break; + case USB_ID(0x1235, 0x8201): + info = &s18i20_gen2_info; + break; + default: /* device not (yet) supported */ + return -EINVAL; + } + + if (!(mixer->chip->setup & SCARLETT2_ENABLE)) { + usb_audio_err(mixer->chip, + "Focusrite Scarlett Gen 2 Mixer Driver disabled; " + "use options snd_usb_audio device_setup=1 " + "to enable and report any issues to g@b4.vu"); + return 0; + } + + /* Initialise private data, routing, sequence number */ + err = scarlett2_init_private(mixer, info); + if (err < 0) + return err; + + /* Read volume levels and controls from the interface */ + err = scarlett2_read_configs(mixer); + if (err < 0) + return err; + + /* Create the analogue output controls */ + err = scarlett2_add_line_out_ctls(mixer); + if (err < 0) + return err; + + /* Create the analogue input controls */ + err = scarlett2_add_line_in_ctls(mixer); + if (err < 0) + return err; + + /* Create the input, output, and mixer mux input selections */ + err = scarlett2_add_mux_enums(mixer); + if (err < 0) + return err; + + /* Create the matrix mixer controls */ + err = scarlett2_add_mixer_ctls(mixer); + if (err < 0) + return err; + + /* Create the level meter controls */ + err = scarlett2_add_meter_ctl(mixer); + if (err < 0) + return err; + + /* Set up the interrupt polling if there are hardware buttons */ + if (info->button_count) { + err = scarlett2_mixer_status_create(mixer); + if (err < 0) + return err; + } + + return 0; +} diff --git a/sound/usb/mixer_scarlett_gen2.h b/sound/usb/mixer_scarlett_gen2.h new file mode 100644 index 000000000000..52e1dad77afd --- /dev/null +++ b/sound/usb/mixer_scarlett_gen2.h @@ -0,0 +1,7 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __USB_MIXER_SCARLETT_GEN2_H +#define __USB_MIXER_SCARLETT_GEN2_H + +int snd_scarlett_gen2_controls_create(struct usb_mixer_interface *mixer); + +#endif /* __USB_MIXER_SCARLETT_GEN2_H */