From: Kuninori Morimoto kuninori.morimoto.gx@renesas.com
In upstream kernel, no one is using SND_SOC_SH4_SSI / sh4-ssi-dai. This patch discontinue support of ssi driver to reducing maintenance cost. Thank you and good bye ssi driver.
Signed-off-by: Kuninori Morimoto kuninori.morimoto.gx@renesas.com --- sound/soc/sh/Kconfig | 3 - sound/soc/sh/Makefile | 2 - sound/soc/sh/ssi.c | 411 ------------------------------------------------- 3 files changed, 416 deletions(-) delete mode 100644 sound/soc/sh/ssi.c
diff --git a/sound/soc/sh/Kconfig b/sound/soc/sh/Kconfig index a931c96..e39d78b 100644 --- a/sound/soc/sh/Kconfig +++ b/sound/soc/sh/Kconfig @@ -17,9 +17,6 @@ config SND_SOC_SH4_HAC select AC97_BUS select SND_SOC_AC97_BUS
-config SND_SOC_SH4_SSI - tristate - config SND_SOC_SH4_FSI tristate "SH4 FSI support" select SND_SIMPLE_CARD diff --git a/sound/soc/sh/Makefile b/sound/soc/sh/Makefile index 20f50ea..6c61f1d 100644 --- a/sound/soc/sh/Makefile +++ b/sound/soc/sh/Makefile @@ -4,11 +4,9 @@ obj-$(CONFIG_SND_SOC_PCM_SH7760) += snd-soc-dma-sh7760.o
## audio units found on some SH-4 snd-soc-hac-objs := hac.o -snd-soc-ssi-objs := ssi.o snd-soc-fsi-objs := fsi.o snd-soc-siu-objs := siu_pcm.o siu_dai.o obj-$(CONFIG_SND_SOC_SH4_HAC) += snd-soc-hac.o -obj-$(CONFIG_SND_SOC_SH4_SSI) += snd-soc-ssi.o obj-$(CONFIG_SND_SOC_SH4_FSI) += snd-soc-fsi.o obj-$(CONFIG_SND_SOC_SH4_SIU) += snd-soc-siu.o
diff --git a/sound/soc/sh/ssi.c b/sound/soc/sh/ssi.c deleted file mode 100644 index ab13146..0000000 --- a/sound/soc/sh/ssi.c +++ /dev/null @@ -1,411 +0,0 @@ -/* - * Serial Sound Interface (I2S) support for SH7760/SH7780 - * - * Copyright (c) 2007 Manuel Lauss mano@roarinelk.homelinux.net - * - * licensed under the terms outlined in the file COPYING at the root - * of the linux kernel sources. - * - * dont forget to set IPSEL/OMSEL register bits (in your board code) to - * enable SSI output pins! - */ - -/* - * LIMITATIONS: - * The SSI unit has only one physical data line, so full duplex is - * impossible. This can be remedied on the SH7760 by using the - * other SSI unit for recording; however the SH7780 has only 1 SSI - * unit, and its pins are shared with the AC97 unit, among others. - * - * FEATURES: - * The SSI features "compressed mode": in this mode it continuously - * streams PCM data over the I2S lines and uses LRCK as a handshake - * signal. Can be used to send compressed data (AC3/DTS) to a DSP. - * The number of bits sent over the wire in a frame can be adjusted - * and can be independent from the actual sample bit depth. This is - * useful to support TDM mode codecs like the AD1939 which have a - * fixed TDM slot size, regardless of sample resolution. - */ - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/platform_device.h> -#include <sound/core.h> -#include <sound/pcm.h> -#include <sound/initval.h> -#include <sound/soc.h> -#include <asm/io.h> - -#define SSICR 0x00 -#define SSISR 0x04 - -#define CR_DMAEN (1 << 28) -#define CR_CHNL_SHIFT 22 -#define CR_CHNL_MASK (3 << CR_CHNL_SHIFT) -#define CR_DWL_SHIFT 19 -#define CR_DWL_MASK (7 << CR_DWL_SHIFT) -#define CR_SWL_SHIFT 16 -#define CR_SWL_MASK (7 << CR_SWL_SHIFT) -#define CR_SCK_MASTER (1 << 15) /* bitclock master bit */ -#define CR_SWS_MASTER (1 << 14) /* wordselect master bit */ -#define CR_SCKP (1 << 13) /* I2Sclock polarity */ -#define CR_SWSP (1 << 12) /* LRCK polarity */ -#define CR_SPDP (1 << 11) -#define CR_SDTA (1 << 10) /* i2s alignment (msb/lsb) */ -#define CR_PDTA (1 << 9) /* fifo data alignment */ -#define CR_DEL (1 << 8) /* delay data by 1 i2sclk */ -#define CR_BREN (1 << 7) /* clock gating in burst mode */ -#define CR_CKDIV_SHIFT 4 -#define CR_CKDIV_MASK (7 << CR_CKDIV_SHIFT) /* bitclock divider */ -#define CR_MUTE (1 << 3) /* SSI mute */ -#define CR_CPEN (1 << 2) /* compressed mode */ -#define CR_TRMD (1 << 1) /* transmit/receive select */ -#define CR_EN (1 << 0) /* enable SSI */ - -#define SSIREG(reg) (*(unsigned long *)(ssi->mmio + (reg))) - -struct ssi_priv { - unsigned long mmio; - unsigned long sysclk; - int inuse; -} ssi_cpu_data[] = { -#if defined(CONFIG_CPU_SUBTYPE_SH7760) - { - .mmio = 0xFE680000, - }, - { - .mmio = 0xFE690000, - }, -#elif defined(CONFIG_CPU_SUBTYPE_SH7780) - { - .mmio = 0xFFE70000, - }, -#else -#error "Unsupported SuperH SoC" -#endif -}; - -/* - * track usage of the SSI; it is simplex-only so prevent attempts of - * concurrent playback + capture. FIXME: any locking required? - */ -static int ssi_startup(struct snd_pcm_substream *substream, - struct snd_soc_dai *dai) -{ - struct ssi_priv *ssi = &ssi_cpu_data[dai->id]; - if (ssi->inuse) { - pr_debug("ssi: already in use!\n"); - return -EBUSY; - } else - ssi->inuse = 1; - return 0; -} - -static void ssi_shutdown(struct snd_pcm_substream *substream, - struct snd_soc_dai *dai) -{ - struct ssi_priv *ssi = &ssi_cpu_data[dai->id]; - - ssi->inuse = 0; -} - -static int ssi_trigger(struct snd_pcm_substream *substream, int cmd, - struct snd_soc_dai *dai) -{ - struct ssi_priv *ssi = &ssi_cpu_data[dai->id]; - - switch (cmd) { - case SNDRV_PCM_TRIGGER_START: - SSIREG(SSICR) |= CR_DMAEN | CR_EN; - break; - case SNDRV_PCM_TRIGGER_STOP: - SSIREG(SSICR) &= ~(CR_DMAEN | CR_EN); - break; - default: - return -EINVAL; - } - - return 0; -} - -static int ssi_hw_params(struct snd_pcm_substream *substream, - struct snd_pcm_hw_params *params, - struct snd_soc_dai *dai) -{ - struct ssi_priv *ssi = &ssi_cpu_data[dai->id]; - unsigned long ssicr = SSIREG(SSICR); - unsigned int bits, channels, swl, recv, i; - - channels = params_channels(params); - bits = params->msbits; - recv = (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ? 0 : 1; - - pr_debug("ssi_hw_params() enter\nssicr was %08lx\n", ssicr); - pr_debug("bits: %u channels: %u\n", bits, channels); - - ssicr &= ~(CR_TRMD | CR_CHNL_MASK | CR_DWL_MASK | CR_PDTA | - CR_SWL_MASK); - - /* direction (send/receive) */ - if (!recv) - ssicr |= CR_TRMD; /* transmit */ - - /* channels */ - if ((channels < 2) || (channels > 8) || (channels & 1)) { - pr_debug("ssi: invalid number of channels\n"); - return -EINVAL; - } - ssicr |= ((channels >> 1) - 1) << CR_CHNL_SHIFT; - - /* DATA WORD LENGTH (DWL): databits in audio sample */ - i = 0; - switch (bits) { - case 32: ++i; - case 24: ++i; - case 22: ++i; - case 20: ++i; - case 18: ++i; - case 16: ++i; - ssicr |= i << CR_DWL_SHIFT; - case 8: break; - default: - pr_debug("ssi: invalid sample width\n"); - return -EINVAL; - } - - /* - * SYSTEM WORD LENGTH: size in bits of half a frame over the I2S - * wires. This is usually bits_per_sample x channels/2; i.e. in - * Stereo mode the SWL equals DWL. SWL can be bigger than the - * product of (channels_per_slot x samplebits), e.g. for codecs - * like the AD1939 which only accept 32bit wide TDM slots. For - * "standard" I2S operation we set SWL = chans / 2 * DWL here. - * Waiting for ASoC to get TDM support ;-) - */ - if ((bits > 16) && (bits <= 24)) { - bits = 24; /* these are padded by the SSI */ - /*ssicr |= CR_PDTA;*/ /* cpu/data endianness ? */ - } - i = 0; - swl = (bits * channels) / 2; - switch (swl) { - case 256: ++i; - case 128: ++i; - case 64: ++i; - case 48: ++i; - case 32: ++i; - case 16: ++i; - ssicr |= i << CR_SWL_SHIFT; - case 8: break; - default: - pr_debug("ssi: invalid system word length computed\n"); - return -EINVAL; - } - - SSIREG(SSICR) = ssicr; - - pr_debug("ssi_hw_params() leave\nssicr is now %08lx\n", ssicr); - return 0; -} - -static int ssi_set_sysclk(struct snd_soc_dai *cpu_dai, int clk_id, - unsigned int freq, int dir) -{ - struct ssi_priv *ssi = &ssi_cpu_data[cpu_dai->id]; - - ssi->sysclk = freq; - - return 0; -} - -/* - * This divider is used to generate the SSI_SCK (I2S bitclock) from the - * clock at the HAC_BIT_CLK ("oversampling clock") pin. - */ -static int ssi_set_clkdiv(struct snd_soc_dai *dai, int did, int div) -{ - struct ssi_priv *ssi = &ssi_cpu_data[dai->id]; - unsigned long ssicr; - int i; - - i = 0; - ssicr = SSIREG(SSICR) & ~CR_CKDIV_MASK; - switch (div) { - case 16: ++i; - case 8: ++i; - case 4: ++i; - case 2: ++i; - SSIREG(SSICR) = ssicr | (i << CR_CKDIV_SHIFT); - case 1: break; - default: - pr_debug("ssi: invalid sck divider %d\n", div); - return -EINVAL; - } - - return 0; -} - -static int ssi_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) -{ - struct ssi_priv *ssi = &ssi_cpu_data[dai->id]; - unsigned long ssicr = SSIREG(SSICR); - - pr_debug("ssi_set_fmt()\nssicr was 0x%08lx\n", ssicr); - - ssicr &= ~(CR_DEL | CR_PDTA | CR_BREN | CR_SWSP | CR_SCKP | - CR_SWS_MASTER | CR_SCK_MASTER); - - switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { - case SND_SOC_DAIFMT_I2S: - break; - case SND_SOC_DAIFMT_RIGHT_J: - ssicr |= CR_DEL | CR_PDTA; - break; - case SND_SOC_DAIFMT_LEFT_J: - ssicr |= CR_DEL; - break; - default: - pr_debug("ssi: unsupported format\n"); - return -EINVAL; - } - - switch (fmt & SND_SOC_DAIFMT_CLOCK_MASK) { - case SND_SOC_DAIFMT_CONT: - break; - case SND_SOC_DAIFMT_GATED: - ssicr |= CR_BREN; - break; - } - - switch (fmt & SND_SOC_DAIFMT_INV_MASK) { - case SND_SOC_DAIFMT_NB_NF: - ssicr |= CR_SCKP; /* sample data at low clkedge */ - break; - case SND_SOC_DAIFMT_NB_IF: - ssicr |= CR_SCKP | CR_SWSP; - break; - case SND_SOC_DAIFMT_IB_NF: - break; - case SND_SOC_DAIFMT_IB_IF: - ssicr |= CR_SWSP; /* word select starts low */ - break; - default: - pr_debug("ssi: invalid inversion\n"); - return -EINVAL; - } - - switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { - case SND_SOC_DAIFMT_CBM_CFM: - break; - case SND_SOC_DAIFMT_CBS_CFM: - ssicr |= CR_SCK_MASTER; - break; - case SND_SOC_DAIFMT_CBM_CFS: - ssicr |= CR_SWS_MASTER; - break; - case SND_SOC_DAIFMT_CBS_CFS: - ssicr |= CR_SWS_MASTER | CR_SCK_MASTER; - break; - default: - pr_debug("ssi: invalid master/slave configuration\n"); - return -EINVAL; - } - - SSIREG(SSICR) = ssicr; - pr_debug("ssi_set_fmt() leave\nssicr is now 0x%08lx\n", ssicr); - - return 0; -} - -/* the SSI depends on an external clocksource (at HAC_BIT_CLK) even in - * Master mode, so really this is board specific; the SSI can do any - * rate with the right bitclk and divider settings. - */ -#define SSI_RATES \ - SNDRV_PCM_RATE_8000_192000 - -/* the SSI can do 8-32 bit samples, with 8 possible channels */ -#define SSI_FMTS \ - (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_U8 | \ - SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_U16_LE | \ - SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_U20_3LE | \ - SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_U24_3LE | \ - SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_U32_LE) - -static const struct snd_soc_dai_ops ssi_dai_ops = { - .startup = ssi_startup, - .shutdown = ssi_shutdown, - .trigger = ssi_trigger, - .hw_params = ssi_hw_params, - .set_sysclk = ssi_set_sysclk, - .set_clkdiv = ssi_set_clkdiv, - .set_fmt = ssi_set_fmt, -}; - -static struct snd_soc_dai_driver sh4_ssi_dai[] = { -{ - .name = "ssi-dai.0", - .playback = { - .rates = SSI_RATES, - .formats = SSI_FMTS, - .channels_min = 2, - .channels_max = 8, - }, - .capture = { - .rates = SSI_RATES, - .formats = SSI_FMTS, - .channels_min = 2, - .channels_max = 8, - }, - .ops = &ssi_dai_ops, -}, -#ifdef CONFIG_CPU_SUBTYPE_SH7760 -{ - .name = "ssi-dai.1", - .playback = { - .rates = SSI_RATES, - .formats = SSI_FMTS, - .channels_min = 2, - .channels_max = 8, - }, - .capture = { - .rates = SSI_RATES, - .formats = SSI_FMTS, - .channels_min = 2, - .channels_max = 8, - }, - .ops = &ssi_dai_ops, -}, -#endif -}; - -static const struct snd_soc_component_driver sh4_ssi_component = { - .name = "sh4-ssi", -}; - -static int sh4_soc_dai_probe(struct platform_device *pdev) -{ - return snd_soc_register_component(&pdev->dev, &sh4_ssi_component, - sh4_ssi_dai, ARRAY_SIZE(sh4_ssi_dai)); -} - -static int sh4_soc_dai_remove(struct platform_device *pdev) -{ - snd_soc_unregister_component(&pdev->dev); - return 0; -} - -static struct platform_driver sh4_ssi_driver = { - .driver = { - .name = "sh4-ssi-dai", - }, - - .probe = sh4_soc_dai_probe, - .remove = sh4_soc_dai_remove, -}; - -module_platform_driver(sh4_ssi_driver); - -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("SuperH onchip SSI (I2S) audio driver"); -MODULE_AUTHOR("Manuel Lauss mano@roarinelk.homelinux.net");