@@ -464,16 +488,79 @@ static int acp63_sdw_platform_probe(struct platform_device *pdev) status = devm_snd_soc_register_component(&pdev->dev, &acp63_sdw_component, NULL, 0);
- if (status)
- if (status) { dev_err(&pdev->dev, "Fail to register sdw dma component\n");
return status;- }
- pm_runtime_set_autosuspend_delay(&pdev->dev, ACP_SUSPEND_DELAY_MS);
- pm_runtime_use_autosuspend(&pdev->dev);
- pm_runtime_enable(&pdev->dev);
- pm_runtime_allow(&pdev->dev);
Can you remind me why you need the pm_runtime_allow()? I can't recall where the _forbid() is done.
We have used pm_runtime_allow() to allow the device immediately enter runtime suspend state. Yes you are correct. If we use pm_runtime_allow(), then in remove sequence we should use pm_runtime_forbid call.
Also is there not a pm_runtime_set_active() missing?
We will change the sequence as mentioned below.
in probe sequence , we will use
pm_runtime_set_autosuspend_delay(&pdev->dev, ACP_SUSPEND_DELAY_MS); pm_runtime_use_autosuspend(&pdev->dev); pm_runtime_mark_last_busy(&pdev->dev); pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev);
In remove sequence
pm_runtime_disable(&pdev->dev);
sounds about right.
- return 0;
+}
- return status;
+static int acp63_sdw_platform_remove(struct platform_device *pdev) +{
- pm_runtime_disable(&pdev->dev);
- return 0;
}
+static int __maybe_unused acp63_sdw_pcm_resume(struct device *dev) +{
- struct sdw_dma_dev_data *sdw_data;
- struct acp_sdw_dma_stream *stream;
- struct snd_pcm_runtime *runtime;
- u32 period_bytes, buf_size, water_mark_size_reg;
- int ret;
- int index;
- sdw_data = dev_get_drvdata(dev);
- for (index = 0; index < ACP63_SDW0_DMA_MAX_STREAMS; index++) {
if (sdw_data->sdw0_dma_stream[index] &&sdw_data->sdw0_dma_stream[index]->runtime) {water_mark_size_reg = sdw0_dma_ring_buf_reg[index].water_mark_size_reg;runtime = sdw_data->sdw0_dma_stream[index]->runtime;stream = runtime->private_data;period_bytes = frames_to_bytes(runtime, runtime->period_size);buf_size = frames_to_bytes(runtime, runtime->buffer_size);acp63_config_dma(stream, sdw_data->acp_base, index);ret = acp63_configure_sdw_ringbuffer(sdw_data->acp_base, index,buf_size, ACP_SDW0);if (ret)return ret;writel(period_bytes, sdw_data->acp_base + water_mark_size_reg);}- }
- for (index = 0; index < ACP63_SDW1_DMA_MAX_STREAMS; index++) {
if (sdw_data->sdw1_dma_stream[index] &&sdw_data->sdw1_dma_stream[index]->runtime) {water_mark_size_reg = sdw1_dma_ring_buf_reg[index].water_mark_size_reg;runtime = sdw_data->sdw1_dma_stream[index]->runtime;stream = runtime->private_data;period_bytes = frames_to_bytes(runtime, runtime->period_size);buf_size = frames_to_bytes(runtime, runtime->buffer_size);acp63_config_dma(stream, sdw_data->acp_base, index);ret = acp63_configure_sdw_ringbuffer(sdw_data->acp_base, index,buf_size, ACP_SDW1);if (ret)return ret;writel(period_bytes, sdw_data->acp_base + water_mark_size_reg);}- }
Isn't this set of configurations something that needs to be done already somewhere else, i.e. could there be a common helper?
In hw_params() callback, we are setting period_bytes and buf_size from params structure. We are extracting same variables from runtime structures in resume() callback. We can implement a helper function to further simplify above logic instead of having two separate loops.
ok