On 30/07/2019 15:58, Mark Brown wrote:
On Tue, Jul 30, 2019 at 01:09:36PM +0100, Thomas Preston wrote:
index 000000000000..0f82a88bc1a4 --- /dev/null +++ b/sound/soc/codecs/tda7802.c @@ -0,0 +1,509 @@ +// SPDX-License-Identifier: GPL-2.0 +/*
- tda7802.c -- codec driver for ST TDA7802
Please make the entire comment a C++ one so this looks intentional.
Ok thanks.
+static int tda7802_digital_mute(struct snd_soc_dai *dai, int mute) +{
- const u8 mute_disabled = mute ? 0 : IB2_DIGITAL_MUTE_DISABLED;
Please write normal conditional statements to make the code easier to read.
On it.
- case SND_SOC_BIAS_STANDBY:
err = regulator_enable(tda7802->enable_reg);if (err < 0) {dev_err(component->dev, "Could not enable.\n");return err;}dev_dbg(component->dev, "Regulator enabled\n");msleep(ENABLE_DELAY_MS);Is this delay needed by the device or is it for the regulator to ramp? If it's for the regulator to ramp then the regulator should be doing it.
According to the datasheet the device itself takes 10ms to rise from 0V after PLLen is enabled. There are additional rise times but they are negligible with default capacitor configuration (which we have).
Good to know about the regulator rising configuration though. Thanks.
- case SND_SOC_BIAS_OFF:
regcache_mark_dirty(component->regmap);If the regulator is going off you should really be marking the device as cache only.
Got it, thanks.
err = regulator_disable(tda7802->enable_reg);if (err < 0)dev_err(component->dev, "Could not disable.\n");Any non-zero value from regulator_disable() is an error, there's similar error checking issues in other places.
I return the error at the end of the function, but I'll bring it back here for consistency.
+static const struct snd_kcontrol_new tda7802_snd_controls[] = {
- SOC_SINGLE("Channel 4 Tristate", TDA7802_IB0, 7, 1, 0),
- SOC_SINGLE("Channel 3 Tristate", TDA7802_IB0, 6, 1, 0),
- SOC_SINGLE("Channel 2 Tristate", TDA7802_IB0, 5, 1, 0),
- SOC_SINGLE("Channel 1 Tristate", TDA7802_IB0, 4, 1, 0),
These look like simple on/off switches so should have Switch at the end of the control name. It's also not clear to me why this is exported to userspace - why would this change at runtime and won't any changes need to be coordinated with whatever else is connected to the signal?
- SOC_ENUM("Mute time", mute_time),
- SOC_SINGLE("Unmute channels 1 & 3", TDA7802_IB2, 4, 1, 0),
- SOC_SINGLE("Unmute channels 2 & 4", TDA7802_IB2, 3, 1, 0),
These are also Switch controls. There are *lots* of problems with control names, see control-names.rst.
Ok thanks, I didn't know about the "Switch" suffix, I will read control-names.rst.
I will move Tristate to DT properties. I was also unsure about the Impedance Efficiency Optimiser but the datasheet doesn't go into much detail about this so I left it exposed.
They both seemed like user configurable options in the context of a test rig, but I agree - who knows what this output might be connected to in other systems. I will lock them down in DT. Thanks.
+static const struct snd_soc_component_driver tda7802_component_driver = {
- .set_bias_level = tda7802_set_bias_level,
- .idle_bias_on = 1,
Any reason to keep the device powered up? It looks like the power on process is just powering things up and writing the register cache out and there's not that many registers so the delay is trivial.
Ah no, I think that's a mistake. I want the PLLen to switch off in idle/suspend and the device should restore on wake.
- tda7802->enable_reg = devm_regulator_get(dev, "enable");
- if (IS_ERR(tda7802->enable_reg)) {
dev_err(dev, "Failed to get enable regulator\n");It's better to print error codes if you have them and are printing a diagnostic so people have more to go on when debugging problems.
Yep on it.
Many thanks, I appreciate the feedback.