From: Barry Song barry.song@analog.com
Some of the Blackfin options don't directly follow the kconfig options they depend on, so kconfig is unable to display the proper tree. So sort the options such they expand/collapse properly.
Signed-off-by: Barry Song barry.song@analog.com Signed-off-by: Mike Frysinger vapier@gentoo.org --- sound/soc/blackfin/Kconfig | 98 ++++++++++++++++++++++---------------------- 1 files changed, 49 insertions(+), 49 deletions(-)
diff --git a/sound/soc/blackfin/Kconfig b/sound/soc/blackfin/Kconfig index ac927ff..f91dcb1 100644 --- a/sound/soc/blackfin/Kconfig +++ b/sound/soc/blackfin/Kconfig @@ -7,15 +7,6 @@ config SND_BF5XX_I2S mode (supports single stereo In/Out). You will also need to select the audio interfaces to support below.
-config SND_BF5XX_TDM - tristate "SoC I2S(TDM mode) Audio for the ADI BF5xx chip" - depends on (BLACKFIN && SND_SOC) - help - Say Y or M if you want to add support for codecs attached to - the Blackfin SPORT (synchronous serial ports) interface in TDM - mode. - You will also need to select the audio interfaces to support below. - config SND_BF5XX_SOC_SSM2602 tristate "SoC SSM2602 Audio support for BF52x ezkit" depends on SND_BF5XX_I2S @@ -41,6 +32,31 @@ config SND_BFIN_AD73311_SE Enter the GPIO used to control AD73311's SE pin. Acceptable values are 0 to 7
+config SND_BF5XX_TDM + tristate "SoC I2S(TDM mode) Audio for the ADI BF5xx chip" + depends on (BLACKFIN && SND_SOC) + help + Say Y or M if you want to add support for codecs attached to + the Blackfin SPORT (synchronous serial ports) interface in TDM + mode. + You will also need to select the audio interfaces to support below. + +config SND_BF5XX_SOC_AD1836 + tristate "SoC AD1836 Audio support for BF5xx" + depends on SND_BF5XX_TDM + select SND_BF5XX_SOC_TDM + select SND_SOC_AD1836 + help + Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. + +config SND_BF5XX_SOC_AD1938 + tristate "SoC AD1938 Audio support for Blackfin" + depends on SND_BF5XX_TDM + select SND_BF5XX_SOC_TDM + select SND_SOC_AD1938 + help + Say Y if you want to add support for AD1938 codec on Blackfin. + config SND_BF5XX_AC97 tristate "SoC AC97 Audio for the ADI BF5xx chip" depends on BLACKFIN @@ -71,6 +87,30 @@ config SND_BF5XX_MULTICHAN_SUPPORT Say y if you want AC97 driver to support up to 5.1 channel audio. this mode will consume much more memory for DMA.
+config SND_BF5XX_HAVE_COLD_RESET + bool "BOARD has COLD Reset GPIO" + depends on SND_BF5XX_AC97 + default y if BFIN548_EZKIT + default n if !BFIN548_EZKIT + +config SND_BF5XX_RESET_GPIO_NUM + int "Set a GPIO for cold reset" + depends on SND_BF5XX_HAVE_COLD_RESET + range 0 159 + default 19 if BFIN548_EZKIT + default 5 if BFIN537_STAMP + default 0 + help + Set the correct GPIO for RESET the sound chip. + +config SND_BF5XX_SOC_AD1980 + tristate "SoC AD1980/1 Audio support for BF5xx" + depends on SND_BF5XX_AC97 + select SND_BF5XX_SOC_AC97 + select SND_SOC_AD1980 + help + Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. + config SND_BF5XX_SOC_SPORT tristate
@@ -88,30 +128,6 @@ config SND_BF5XX_SOC_AC97 select SND_SOC_AC97_BUS select SND_BF5XX_SOC_SPORT
-config SND_BF5XX_SOC_AD1836 - tristate "SoC AD1836 Audio support for BF5xx" - depends on SND_BF5XX_TDM - select SND_BF5XX_SOC_TDM - select SND_SOC_AD1836 - help - Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. - -config SND_BF5XX_SOC_AD1980 - tristate "SoC AD1980/1 Audio support for BF5xx" - depends on SND_BF5XX_AC97 - select SND_BF5XX_SOC_AC97 - select SND_SOC_AD1980 - help - Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT. - -config SND_BF5XX_SOC_AD1938 - tristate "SoC AD1938 Audio support for Blackfin" - depends on SND_BF5XX_TDM - select SND_BF5XX_SOC_TDM - select SND_SOC_AD1938 - help - Say Y if you want to add support for AD1938 codec on Blackfin. - config SND_BF5XX_SPORT_NUM int "Set a SPORT for Sound chip" depends on (SND_BF5XX_I2S || SND_BF5XX_AC97 || SND_BF5XX_TDM) @@ -120,19 +136,3 @@ config SND_BF5XX_SPORT_NUM default 0 help Set the correct SPORT for sound chip. - -config SND_BF5XX_HAVE_COLD_RESET - bool "BOARD has COLD Reset GPIO" - depends on SND_BF5XX_AC97 - default y if BFIN548_EZKIT - default n if !BFIN548_EZKIT - -config SND_BF5XX_RESET_GPIO_NUM - int "Set a GPIO for cold reset" - depends on SND_BF5XX_HAVE_COLD_RESET - range 0 159 - default 19 if BFIN548_EZKIT - default 5 if BFIN537_STAMP - default 0 - help - Set the correct GPIO for RESET the sound chip.