From: Kenneth Westfield kwestfie@codeaurora.org
This patch series adds support for I2S audio playback on the Qualcomm Technologies ipq806x SOC.
The ipq806x SOC has audio-related hardware blocks in its low-power audio subsystem (or LPASS). One of the relevant blocks in the LPASS is its low-power audio interface (or LPAIF). This contains an MI2S port, which is what these drivers are configured to use. The LPAIF also contains a DMA engine that is dedicated to moving audio samples into the transmit FIFO of the MI2S port. In addition, there is also low-power memory (LPM) within the audio subsystem, which is used for buffering the audio samples.
The development board being used for testing contains the ipq806x SOC and a Maxim max98357a DAC/amp. One bus from the MI2S port of the SOC is connected to the DAC/amp for stereo playback. This bus is configured so that the SOC is bus master and consists of DATA, LRCLK, and BCLK. The DAC/amp does not need MCLK to operate. In addition, a single GPIO pin from the SOC is connected to the same DAC/amp, which gives enable/disable control over the DAC/amp.
The specific drivers added are: * a codec DAI driver for controlling the DAC/amp * a CPU DAI driver for controlling the MI2S port * a platform driver for controlling the LPAIF DMA engine
These drivers, together, are tied into simple-audio-card to complete the audio implementation. Corresponding additions to the device tree for the ipq806x SOC and its documentation has also been added. Also, as this is a new directory, the MAINTAINERS file has been updated as well.
The LPASS also contains clocks that need to be controlled. Those drivers have been submitted as a separate patch series: [PATCH v3 0/8] qcom audio clock control drivers http://lkml.org/lkml/2015/1/19/656
= Changes since V3 [Patch V3 00/10] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2014-December/085694.ht...
* Placed the content of the inline functions into the callbacks. * Replaced use of readl/writel register access functions with regmap access functions. Notable exception is the ISR, which uses ioread32/iowrite32. * Rearranged the sequencing of the hardware block enables to fit within the ASoC framework callbacks, while remaining functional. REQ 1: The hardware requires the enable sequence to be: LPAIF-DMA[enable],then LPAIF-MI2S[enable], then DAC-GPIO[enable] REQ 2: The hardware requires the disable sequence to be: DAC-GPIO[disable], then LPAIF-MI2S[disable] * Corrected the implementation of the pointer callback. * Utilize the LPM to buffer audio samples, rather than memory external to LPASS. * Corrected the interrupt clearing in the ISR. * Implemented a default system clock (defined by the simple-card DT node), and optional LPASS DT node modifiers that can alter the system clock in order to expand the range of available bit clock frequencies. * Addressed all of the remaining issues raised by Mark Brown. * General code cleanup.
= Changes since V2 [Patch v2 00/11] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2014-December/085186.ht...
* Removed the PCM platform driver from the DTS platform and tied it to the CPU DAI driver. * Changed I2S pinctrl to use generic naming convention and moved control to CPU DAI driver. It should be controlled now by soc-core's pinctrl_pm_* functionality. * Added stub DAPM support in codec driver. As the DAC GPIO needs to be enabled last when starting playback, and disabled first when stopping playback, it seems as though the trigger function may be the place for this. Suggestions are welcome for a better place to put this. * Removed machine driver and tied DAI drivers to simple-audio-card. * Packaged the build files and Maxim codec files together in one change. * Removed QCOM as vendor from Maxim code and documentation. * Separated the SOC and board definitions into the correct DTS files. * Update device tree documentation to reflect changes. * General code cleanup.
= Changes since V1 [PATCH 0/9] ASoC: QCOM: Add support for ipq806x SOC http://mailman.alsa-project.org/pipermail/alsa-devel/2014-November/084322.ht...
* Remove the native LPAIF driver, and move its functionality to the CPU DAI driver. * Add a codec driver to manage the pins going to the external DAC (previously managed by the machine driver). * Use devm_* and dev_* where possible. * ISR only handles relevant DMA channel now. * Update device tree documentation to reflect changes. * General code cleanup.
Kenneth Westfield (10): MAINTAINERS: Add QCOM audio ASoC maintainer ASoC: max98357a: Document MAX98357A bindings ASoC: qcom: Document LPASS CPU bindings ASoC: codec: Add MAX98357A codec driver ASoC: ipq806x: add LPASS header files ASoC: ipq806x: Add LPASS CPU DAI driver ASoC: ipq806x: Add LPASS platform driver ASoC: qcom: Add ability to build QCOM drivers ASoC: Allow for building QCOM drivers ARM: dts: Model IPQ LPASS audio hardware
.../devicetree/bindings/sound/max98357a.txt | 14 + .../devicetree/bindings/sound/qcom,lpass-cpu.txt | 66 +++ MAINTAINERS | 7 + arch/arm/boot/dts/qcom-ipq8064.dtsi | 23 + sound/soc/Kconfig | 1 + sound/soc/Makefile | 1 + sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max98357a.c | 138 +++++ sound/soc/qcom/Kconfig | 27 + sound/soc/qcom/Makefile | 6 + sound/soc/qcom/lpass-cpu.c | 557 +++++++++++++++++++++ sound/soc/qcom/lpass-lpaif-ipq806x.h | 170 +++++++ sound/soc/qcom/lpass-platform.c | 514 +++++++++++++++++++ sound/soc/qcom/lpass.h | 64 +++ 15 files changed, 1594 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/max98357a.txt create mode 100644 Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt create mode 100644 sound/soc/codecs/max98357a.c create mode 100644 sound/soc/qcom/Kconfig create mode 100644 sound/soc/qcom/Makefile create mode 100644 sound/soc/qcom/lpass-cpu.c create mode 100644 sound/soc/qcom/lpass-lpaif-ipq806x.h create mode 100644 sound/soc/qcom/lpass-platform.c create mode 100644 sound/soc/qcom/lpass.h