Hello,
I did some tests with the SyncIn-Feature of the HDSPe cards.
[root@localhost ~]# lspci |grep Mult 01:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall DSP MADI (rev d2) 02:00.0 Multimedia audio controller: Xilinx Corporation RME Hammerfall DSP MADI (rev d2)
The SyncOut of card 2:00 was plugged to the SyncIn of 1:00 and 1:00 was put to AutoSync-mode automatically upon boot. Problem is that the amixer output seems to be inconsistent and differs from the proc output as well, so I'm not sure which one to trust.
[root@localhost ~]# amixer -c0 contents numid=5,iface=MIXER,name='AutoSync Reference' ; type=ENUMERATED,access=r-------,values=1,items=5 ; Item #0 'Word Clock' ; Item #1 'MADI' ; Item #2 'TCO' ; Item #3 'Sync In' ; Item #4 'None' : values=3 numid=2,iface=MIXER,name='Internal Clock' ; type=ENUMERATED,access=rw------,values=1,items=9 ; Item #0 '32 kHz' ; Item #1 '44.1 kHz' ; Item #2 '48 kHz' ; Item #3 '64 kHz' ; Item #4 '88.2 kHz' ; Item #5 '96 kHz' ; Item #6 '128 kHz' ; Item #7 '176.4 kHz' ; Item #8 '192 kHz' : values=2 numid=4,iface=MIXER,name='Preferred Sync Reference' ; type=ENUMERATED,access=rw------,values=1,items=3 ; Item #0 'Word Clock' ; Item #1 'MADI' ; Item #2 'Sync In' : values=2 numid=10,iface=MIXER,name='SYNC IN SyncCheck' ; type=ENUMERATED,access=r-------,values=1,items=4 ; Item #0 'No Lock' ; Item #1 'Lock' ; Item #2 'Sync' ; Item #3 'N/A' : values=0 numid=3,iface=MIXER,name='System Clock Mode' ; type=ENUMERATED,access=rw------,values=1,items=2 ; Item #0 'Master' ; Item #1 'AutoSync' : values=1 numid=6,iface=MIXER,name='System Sample Rate' ; type=INTEGER,access=r-------,values=1,min=27000,max=207000,step=1 : values=47999
'Preferred Sync Reference' is SyncIn, 'SYNC IN SyncCheck' says 'No Lock', meaning no signal at all, but the 'System Sample Rate' coming from the master card is detected with 1Hz offset. When putting the master to 32000Hz, 31999Hz are shown and so on.
[root@localhost ~]# cat /proc/asound/card0/hdspm RME MADI (Card #1) Rev.d2 Status2first3bits: 1 HW Serial: 0x0000019196d4 IRQ: 16 Registers bus: 0xfe9f0000 VM: 0xf8920000 --- System --- IRQ Pending: Audio=0, MIDI0=0, MIDI1=0, IRQcount=0 HW pointer: id = 0, rawptr = 0 (0->16320) estimated= 0 (bytes) MIDI FIFO: Out1=0x0, Out2=0x0, In1=0x0, In2=0x0 MIDIoverMADI FIFO: In=0x0, Out=0x0 Register: ctrl1=0x10344ca, ctrl2=0x0, status1=0xc30004, status2=0xc0020361 No TCO module detected. --- Settings --- Size (Latency): 2048 samples (2 periods of 8192 bytes) Line out: on ClearTrackMarker = off, Transmit in 64 Channel Mode, Auto Input off AutoSync Reference: AutoSync Preferred Sync Reference: TCO System Clock Frequency: 48000 --- Status: Inputs MADI=NoLock, WordClock=NoLock AutoSync: Reference= Sync In, Freq=0 (MADI = 3, Word = 3) Input: Coax, Mode=56 channels
Now the proc-output reports 'No TCO module detected', which is correct, as no expansion modules where plugged to the cards. But it also says 'Preferred Sync Reference: TCO' and 'Freq=0', where amixer said SyncIn and 47999? Output of the master card is below.
Regards, Andre
[root@localhost ~]# amixer -c1 contents numid=5,iface=MIXER,name='AutoSync Reference' ; type=ENUMERATED,access=r-------,values=1,items=5 ; Item #0 'Word Clock' ; Item #1 'MADI' ; Item #2 'TCO' ; Item #3 'Sync In' ; Item #4 'None' : values=4 numid=15,iface=MIXER,name='Input Select' ; type=ENUMERATED,access=rw------,values=1,items=2 ; Item #0 'optical' ; Item #1 'coaxial' : values=0 numid=2,iface=MIXER,name='Internal Clock' ; type=ENUMERATED,access=rw------,values=1,items=9 ; Item #0 '32 kHz' ; Item #1 '44.1 kHz' ; Item #2 '48 kHz' ; Item #3 '64 kHz' ; Item #4 '88.2 kHz' ; Item #5 '96 kHz' ; Item #6 '128 kHz' ; Item #7 '176.4 kHz' ; Item #8 '192 kHz' : values=2 numid=4,iface=MIXER,name='Preferred Sync Reference' ; type=ENUMERATED,access=rw------,values=1,items=3 ; Item #0 'Word Clock' ; Item #1 'MADI' ; Item #2 'Sync In' : values=0 numid=10,iface=MIXER,name='SYNC IN SyncCheck' ; type=ENUMERATED,access=r-------,values=1,items=4 ; Item #0 'No Lock' ; Item #1 'Lock' ; Item #2 'Sync' ; Item #3 'N/A' : values=0 numid=3,iface=MIXER,name='System Clock Mode' ; type=ENUMERATED,access=rw------,values=1,items=2 ; Item #0 'Master' ; Item #1 'AutoSync' : values=0 numid=6,iface=MIXER,name='System Sample Rate' ; type=INTEGER,access=r-------,values=1,min=27000,max=207000,step=1 : values=48000
[root@localhost ~]# cat /proc/asound/card1/hdspm RME MADI (Card #2) Rev.d2 Status2first3bits: 1 HW Serial: 0x000001b1c606 IRQ: 17 Registers bus: 0xfeaf0000 VM: 0xf9280000 --- System --- IRQ Pending: Audio=0, MIDI0=0, MIDI1=0, IRQcount=0 HW pointer: id = 0, rawptr = 0 (0->16320) estimated= 0 (bytes) MIDI FIFO: Out1=0x0, Out2=0x0, In1=0x0, In2=0x0 MIDIoverMADI FIFO: In=0x0, Out=0x0 Register: ctrl1=0x10004da, ctrl2=0x0, status1=0x2800000, status2=0xc0020701 No TCO module detected. --- Settings --- Size (Latency): 2048 samples (2 periods of 8192 bytes) Line out: on ClearTrackMarker = off, Transmit in 64 Channel Mode, Auto Input off AutoSync Reference: Master Preferred Sync Reference: Word Clock System Clock Frequency: 48000 --- Status: Inputs MADI=NoLock, WordClock=NoLock AutoSync: Reference= Input not valid, Freq=0 (MADI = 10, Word = 0) Input: Optical, Mode=56 channels