These codecs have a variable number of I/O lines each of which is individually selectable to a wide range of possible functions.
The functionality is slightly different from the traditional muxed GPIO since most of the functions can be mapped to any pin (and even the same function to multiple pins). Most pins have a dedicated "alternate" function that is only available on that pin. The alternate functions are usually a group of signals, though it is not always necessary to enable the full group, depending on the alternate function and how it is to be used. The mapping between alternate functions and GPIO pins varies between codecs depending on the number of alternate functions and available pins.
Signed-off-by: Richard Fitzgerald rf@opensource.wolfsonmicro.com --- .../bindings/pinctrl/cirrus,madera-pinctrl.txt | 103 ++ MAINTAINERS | 2 + drivers/pinctrl/Kconfig | 22 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-madera.c | 1092 ++++++++++++++++++++ 5 files changed, 1220 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt create mode 100644 drivers/pinctrl/pinctrl-madera.c
diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt new file mode 100644 index 0000000..e9e20e6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt @@ -0,0 +1,103 @@ +Cirrus Logic Madera class audio codecs pinctrl driver + +The Cirrus Logic Madera codecs provide a number of GPIO functions for +interfacing to external hardware and to provide logic outputs to other devices. +Certain groups of GPIO pins also have an alternate function, normally as an +audio interface. + +The set of available GPIOs, functions and alternate function groups differs +between codecs so refer to the datasheet for the codec for further information +on what is supported on that device. + +The root node for this driver must be a subnode of the parent MFD driver node. +It contains one subnode that is a container for an arbitrary number of subnodes +to configure each pin or function group. + +See also + the core bindings for the parent MFD driver: + Documentation/devicetree/bindings/mfd/madera.txt + + the generic pinmix bindings: + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Required properties of parent mfd node: + - pinctrl-names : must be "defaults" + - pinctrl-0 : a phandle to the node containing the configuration subnodes + +Required properties of pinctrl subnode: + - compatible : must be "cirrus,madera-pinctrl" + +Required properties of configuration subnodes: + - groups : name of one pin group to configure. One of: + aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2, + dmic4, dmic5, dmic6, + gpio1, gpio2, ..., gpio40 + The gpioN groups select the single pin of this name for configuration + +Optional properties of configuration subnodes: + Any configuration option not explicitly listed in the dts will be left at + chip default setting. + + - function : name of function to assign to this group. One of: + aif1, aif2, aif3, aif4, mif1, mif2, mif3, pdmspk1, pdmspk2, + dmic3, dmic4, dmic5, dmic6, + io, dsp-gpio, irq1, irq2, + fll1-clk, fll1-lock, fll2-clk, fll2-lock, fll3-clk, fll3-lock, + fllao-clk, fllao-lock, + opclk, opclk-async, pwm1, pwm2, spdif, + asrc1-in1-lock, asrc1-in2-lock, asrc2-in1-lock, asrc2-in2-lock, + spkl-short-circuit, spkr-short-circuit, spk-shutdown, + spk-overheat-shutdown, spk-overheat-warn, + timer1-sts, timer2-sts, timer3-sts, timer4-sts, timer5-sts, timer6-sts, + timer7-sts, timer8-sts, + log1-fifo-ne, log2-fifo-ne, log3-fifo-ne, log4-fifo-ne, log5-fifo-ne, + log6-fifo-ne, log7-fifo-ne, log8-fifo-ne, + + - bias-disable : disable pull-up and pull-down + - bias-bus-hold : enable buskeeper + - bias-pull-up : output is pulled-up + - bias-pull-down : output is pulled-down + - drive-push-pull : CMOS output + - drive-open-drain : open-drain output + - drive-strength : drive strength in mA. Valid values are 4 or 8 + - input-schmitt-enable : enable schmitt-trigger mode + - input-schmitt-disable : disable schmitt-trigger mode + - input-debounce : A value of 0 disables debounce, a value !=0 enables + debounce + - output-low : set the pin to output mode with low level + - output-high : set the pin to output mode with high level + +Example: + +codec: cs47l85@0 { + compatible = "cirrus,cs47l85"; + + pinctrl-names = "default"; + pinctrl-0 = <&cs47l85_gpio_defaults>; + + + pinctrl { + compatible = "cirrus,madera-pinctrl"; + + cs47l85_gpio_defaults: defaults { + aif1 { + groups = "aif1"; + function = "aif1"; + bias-bus-hold; + }; + + aif2 { + groups = "aif2"; + function = "aif2"; + bias-bus-hold; + }; + + opclk { + groups = "gpio1"; + function = "opclk"; + bias-pull-up; + drive-strength = <8>; + }; + }; + }; +}; diff --git a/MAINTAINERS b/MAINTAINERS index a06701f..85af1f9 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3268,6 +3268,7 @@ W: https://github.com/CirrusLogic/linux-drivers/wiki S: Supported F: Documentation/devicetree/bindings/interrupt-controller/cirrus,madera.txt F: Documentation/devicetree/bindings/mfd/madera.txt +F: Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt F: Documentation/devicetree/bindings/regulator/madera* F: include/linux/irqchip/irq-madera* F: include/linux/mfd/madera/* @@ -3275,6 +3276,7 @@ F: include/linux/regulator/madera* F: drivers/irqchip/irq-madera* F: drivers/mfd/madera* F: drivers/mfd/cs47l* +F: drivers/pinctrl/pinctrl-madera* F: drivers/regulator/madera*
CLEANCACHE API diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 8f8c2af..483afe5 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -109,6 +109,28 @@ config PINCTRL_DA850_PUPD Driver for TI DA850/OMAP-L138/AM18XX pinconf. Used to control pullup/pulldown pin groups.
+config PINCTRL_MADERA + bool + default y if MFD_MADERA=y + +config PINCTRL_CS47L35 + bool + default y if MFD_CS47L35=y + select PINMUX + select GENERIC_PINCONF + +config PINCTRL_CS47L85 + bool + default y if MFD_CS47L85=y + select PINMUX + select GENERIC_PINCONF + +config PINCTRL_CS47L90 + bool + default y if MFD_CS47L90=y + select PINMUX + select GENERIC_PINCONF + config PINCTRL_DIGICOLOR bool depends on OF && (ARCH_DIGICOLOR || COMPILE_TEST) diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index a251f43..6e6919c 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_AMD) += pinctrl-amd.o obj-$(CONFIG_PINCTRL_DA850_PUPD) += pinctrl-da850-pupd.o obj-$(CONFIG_PINCTRL_DIGICOLOR) += pinctrl-digicolor.o obj-$(CONFIG_PINCTRL_FALCON) += pinctrl-falcon.o +obj-$(CONFIG_PINCTRL_MADERA) += pinctrl-madera.o obj-$(CONFIG_PINCTRL_MAX77620) += pinctrl-max77620.o obj-$(CONFIG_PINCTRL_MESON) += meson/ obj-$(CONFIG_PINCTRL_OXNAS) += pinctrl-oxnas.o diff --git a/drivers/pinctrl/pinctrl-madera.c b/drivers/pinctrl/pinctrl-madera.c new file mode 100644 index 0000000..2cf6021 --- /dev/null +++ b/drivers/pinctrl/pinctrl-madera.c @@ -0,0 +1,1092 @@ +/* + * Pinctrl for Cirrus Logic Madera codecs + * + * Copyright 2016-2017 Cirrus Logic + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/err.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinconf-generic.h> + +#include <linux/mfd/madera/core.h> +#include <linux/mfd/madera/registers.h> + +#include "pinctrl-utils.h" + +/* + * Pins are named after their GPIO number + * NOTE: IDs are zero-indexed for coding convenience + */ +static const struct pinctrl_pin_desc madera_pins[] = { + PINCTRL_PIN(0, "gpio1"), + PINCTRL_PIN(1, "gpio2"), + PINCTRL_PIN(2, "gpio3"), + PINCTRL_PIN(3, "gpio4"), + PINCTRL_PIN(4, "gpio5"), + PINCTRL_PIN(5, "gpio6"), + PINCTRL_PIN(6, "gpio7"), + PINCTRL_PIN(7, "gpio8"), + PINCTRL_PIN(8, "gpio9"), + PINCTRL_PIN(9, "gpio10"), + PINCTRL_PIN(10, "gpio11"), + PINCTRL_PIN(11, "gpio12"), + PINCTRL_PIN(12, "gpio13"), + PINCTRL_PIN(13, "gpio14"), + PINCTRL_PIN(14, "gpio15"), + PINCTRL_PIN(15, "gpio16"), + PINCTRL_PIN(16, "gpio17"), + PINCTRL_PIN(17, "gpio18"), + PINCTRL_PIN(18, "gpio19"), + PINCTRL_PIN(19, "gpio20"), + PINCTRL_PIN(20, "gpio21"), + PINCTRL_PIN(21, "gpio22"), + PINCTRL_PIN(22, "gpio23"), + PINCTRL_PIN(23, "gpio24"), + PINCTRL_PIN(24, "gpio25"), + PINCTRL_PIN(25, "gpio26"), + PINCTRL_PIN(26, "gpio27"), + PINCTRL_PIN(27, "gpio28"), + PINCTRL_PIN(28, "gpio29"), + PINCTRL_PIN(29, "gpio30"), + PINCTRL_PIN(30, "gpio31"), + PINCTRL_PIN(31, "gpio32"), + PINCTRL_PIN(32, "gpio33"), + PINCTRL_PIN(33, "gpio34"), + PINCTRL_PIN(34, "gpio35"), + PINCTRL_PIN(35, "gpio36"), + PINCTRL_PIN(36, "gpio37"), + PINCTRL_PIN(37, "gpio38"), + PINCTRL_PIN(38, "gpio39"), + PINCTRL_PIN(39, "gpio40"), +}; + +/* + * All single-pin functions can be mapped to any GPIO, however pinmux applies + * functions to pin groups and only those groups declared as supporting that + * function. To make this work we must put each pin in its own dummy group so + * that the functions can be described as applying to all pins. + * Since these do not correspond to anything in the actual hardware - they are + * merely an adaptation to pinctrl's view of the world - we use the same name + * as the pin to avoid confusion when comparing with datasheet instructions + */ +static const char * const madera_pin_single_group_names[] = { + "gpio1", "gpio2", "gpio3", "gpio4", "gpio5", "gpio6", "gpio7", + "gpio8", "gpio9", "gpio10", "gpio11", "gpio12", "gpio13", "gpio14", + "gpio15", "gpio16", "gpio17", "gpio18", "gpio19", "gpio20", "gpio21", + "gpio22", "gpio23", "gpio24", "gpio25", "gpio26", "gpio27", "gpio28", + "gpio29", "gpio30", "gpio31", "gpio32", "gpio33", "gpio34", "gpio35", + "gpio36", "gpio37", "gpio38", "gpio39", "gpio40", +}; + +/* set of pin numbers for single-pin groups, zero-indexed */ +static const unsigned int madera_pin_single_group_pins[] = { + 0, 1, 2, 3, 4, 5, 6, + 7, 8, 9, 10, 11, 12, 13, + 14, 15, 16, 17, 18, 19, 20, + 21, 22, 23, 24, 25, 26, 27, + 28, 29, 30, 31, 32, 33, 34, + 35, 36, 37, 38, 39, +}; + +static const char * const madera_aif1_group_names[] = { "aif1" }; +static const char * const madera_aif2_group_names[] = { "aif2" }; +static const char * const madera_aif3_group_names[] = { "aif3" }; +static const char * const madera_aif4_group_names[] = { "aif4" }; +static const char * const madera_mif1_group_names[] = { "mif1" }; +static const char * const madera_mif2_group_names[] = { "mif2" }; +static const char * const madera_mif3_group_names[] = { "mif3" }; +static const char * const madera_dmic3_group_names[] = { "dmic3" }; +static const char * const madera_dmic4_group_names[] = { "dmic4" }; +static const char * const madera_dmic5_group_names[] = { "dmic5" }; +static const char * const madera_dmic6_group_names[] = { "dmic6" }; +static const char * const madera_spk1_group_names[] = { "pdmspk1" }; +static const char * const madera_spk2_group_names[] = { "pdmspk2" }; + +/* + * alt-functions always apply to a single pin group, other functions always + * apply to all pins + */ +static const struct { + const char *name; + const char * const *group_names; + u32 func; +} madera_mux_funcs[] = { + { + .name = "aif1", + .group_names = madera_aif1_group_names, + .func = 0x000 + }, + { + .name = "aif2", + .group_names = madera_aif2_group_names, + .func = 0x000 + }, + { + .name = "aif3", + .group_names = madera_aif3_group_names, + .func = 0x000 + }, + { + .name = "aif4", + .group_names = madera_aif4_group_names, + .func = 0x000 + }, + { + .name = "mif1", + .group_names = madera_mif1_group_names, + .func = 0x000 + }, + { + .name = "mif2", + .group_names = madera_mif2_group_names, + .func = 0x000 + }, + { + .name = "mif3", + .group_names = madera_mif3_group_names, + .func = 0x000 + }, + { + .name = "dmic3", + .group_names = madera_dmic3_group_names, + .func = 0x000 + }, + { + .name = "dmic4", + .group_names = madera_dmic4_group_names, + .func = 0x000 + }, + { + .name = "dmic5", + .group_names = madera_dmic5_group_names, + .func = 0x000 + }, + { + .name = "dmic6", + .group_names = madera_dmic6_group_names, + .func = 0x000 + }, + { + .name = "pdmspk1", + .group_names = madera_spk1_group_names, + .func = 0x000 + }, + { + .name = "pdmspk2", + .group_names = madera_spk2_group_names, + .func = 0x000 + }, + { + .name = "io", + .group_names = madera_pin_single_group_names, + .func = 0x001 + }, + { + .name = "dsp-gpio", + .group_names = madera_pin_single_group_names, + .func = 0x002 + }, + { + .name = "irq1", + .group_names = madera_pin_single_group_names, + .func = 0x003 + }, + { + .name = "irq2", + .group_names = madera_pin_single_group_names, + .func = 0x004 + }, + { + .name = "fll1-clk", + .group_names = madera_pin_single_group_names, + .func = 0x010 + }, + { + .name = "fll2-clk", + .group_names = madera_pin_single_group_names, + .func = 0x011 + }, + { + .name = "fll3-clk", + .group_names = madera_pin_single_group_names, + .func = 0x012 + }, + { + .name = "fllao-clk", + .group_names = madera_pin_single_group_names, + .func = 0x013 + }, + { + .name = "fll1-lock", + .group_names = madera_pin_single_group_names, + .func = 0x018 + }, + { + .name = "fll2-lock", + .group_names = madera_pin_single_group_names, + .func = 0x019 + }, + { + .name = "fll3-lock", + .group_names = madera_pin_single_group_names, + .func = 0x01a + }, + { + .name = "fllao-lock", + .group_names = madera_pin_single_group_names, + .func = 0x01b + }, + { + .name = "opclk", + .group_names = madera_pin_single_group_names, + .func = 0x040 + }, + { + .name = "opclk-async", + .group_names = madera_pin_single_group_names, + .func = 0x041 + }, + { + .name = "pwm1", + .group_names = madera_pin_single_group_names, + .func = 0x048 + }, + { + .name = "pwm2", + .group_names = madera_pin_single_group_names, + .func = 0x049 + }, + { + .name = "spdif", + .group_names = madera_pin_single_group_names, + .func = 0x04c + }, + { + .name = "asrc1-in1-lock", + .group_names = madera_pin_single_group_names, + .func = 0x088 + }, + { + .name = "asrc1-in2-lock", + .group_names = madera_pin_single_group_names, + .func = 0x089 + }, + { + .name = "asrc2-in1-lock", + .group_names = madera_pin_single_group_names, + .func = 0x08a + }, + { + .name = "asrc2-in2-lock", + .group_names = madera_pin_single_group_names, + .func = 0x08b + }, + { + .name = "spkl-short-circuit", + .group_names = madera_pin_single_group_names, + .func = 0x0b6 + }, + { + .name = "spkr-short-circuit", + .group_names = madera_pin_single_group_names, + .func = 0x0b7 + }, + { + .name = "spk-shutdown", + .group_names = madera_pin_single_group_names, + .func = 0x0e0 + }, + { + .name = "spk-overheat-shutdown", + .group_names = madera_pin_single_group_names, + .func = 0x0e1 + }, + { + .name = "spk-overheat-warn", + .group_names = madera_pin_single_group_names, + .func = 0x0e2 + }, + { + .name = "timer1-sts", + .group_names = madera_pin_single_group_names, + .func = 0x140 + }, + { + .name = "timer2-sts", + .group_names = madera_pin_single_group_names, + .func = 0x141 + }, + { + .name = "timer3-sts", + .group_names = madera_pin_single_group_names, + .func = 0x142 + }, + { + .name = "timer4-sts", + .group_names = madera_pin_single_group_names, + .func = 0x143 + }, + { + .name = "timer5-sts", + .group_names = madera_pin_single_group_names, + .func = 0x144 + }, + { + .name = "timer6-sts", + .group_names = madera_pin_single_group_names, + .func = 0x145 + }, + { + .name = "timer7-sts", + .group_names = madera_pin_single_group_names, + .func = 0x146 + }, + { + .name = "timer8-sts", + .group_names = madera_pin_single_group_names, + .func = 0x147 + }, + { + .name = "log1-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x150 + }, + { + .name = "log2-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x151 + }, + { + .name = "log3-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x152 + }, + { + .name = "log4-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x153 + }, + { + .name = "log5-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x154 + }, + { + .name = "log6-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x155 + }, + { + .name = "log7-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x156 + }, + { + .name = "log8-fifo-ne", + .group_names = madera_pin_single_group_names, + .func = 0x157 + }, +}; + +struct madera_pin_groups { + const char *name; + const unsigned int *pins; + unsigned int n_pins; +}; + +struct madera_pin_chip { + unsigned int n_pins; + + const struct madera_pin_groups *pin_groups; + unsigned int n_pin_groups; +}; + +struct madera_pin_private { + struct madera *madera; + + const struct madera_pin_chip *chip; /* chip-specific groups */ + + struct device *dev; + struct pinctrl_dev *pctl; +}; + +/* + * Chip-specific configs + * The alt func groups available differ between codecs. Since these are the + * most commonly used functions we place these at the lower function indexes + * for convenience, and the less commonly used gpio functions at higher indexes + * + * To stay consistent with the datasheet the function names are the same as + * the group names for that function's pins + */ +#ifdef CONFIG_PINCTRL_CS47L35 +/* Note - all 1 less than in datasheet because these are zero-indexed */ +static const unsigned int cs47l35_aif3_pins[] = { 0, 1, 2, 3 }; +static const unsigned int cs47l35_spk_pins[] = { 4, 5 }; +static const unsigned int cs47l35_aif1_pins[] = { 7, 8, 9, 10 }; +static const unsigned int cs47l35_aif2_pins[] = { 11, 12, 13, 14 }; +static const unsigned int cs47l35_mif1_pins[] = { 6, 15 }; + +static const struct madera_pin_groups cs47l35_pin_groups[] = { + { "aif1", cs47l35_aif1_pins, ARRAY_SIZE(cs47l35_aif1_pins) }, + { "aif2", cs47l35_aif2_pins, ARRAY_SIZE(cs47l35_aif2_pins) }, + { "aif3", cs47l35_aif3_pins, ARRAY_SIZE(cs47l35_aif3_pins) }, + { "mif1", cs47l35_mif1_pins, ARRAY_SIZE(cs47l35_mif1_pins) }, + { "pdmspk1", cs47l35_spk_pins, ARRAY_SIZE(cs47l35_spk_pins) }, +}; + +const struct madera_pin_chip cs47l35_pin_chip = { + .n_pins = CS47L35_NUM_GPIOS, + .pin_groups = cs47l35_pin_groups, + .n_pin_groups = ARRAY_SIZE(cs47l35_pin_groups), +}; +#endif + +#ifdef CONFIG_PINCTRL_CS47L85 +/* Note - all 1 less than in datasheet because these are zero-indexed */ +static const unsigned int cs47l85_mif1_pins[] = { 8, 9 }; +static const unsigned int cs47l85_mif2_pins[] = { 10, 11 }; +static const unsigned int cs47l85_mif3_pins[] = { 12, 13 }; +static const unsigned int cs47l85_aif1_pins[] = { 14, 15, 16, 17 }; +static const unsigned int cs47l85_aif2_pins[] = { 18, 19, 20, 21 }; +static const unsigned int cs47l85_aif3_pins[] = { 22, 23, 24, 25 }; +static const unsigned int cs47l85_aif4_pins[] = { 26, 27, 28, 29 }; +static const unsigned int cs47l85_dmic4_pins[] = { 30, 31 }; +static const unsigned int cs47l85_dmic5_pins[] = { 32, 33 }; +static const unsigned int cs47l85_dmic6_pins[] = { 34, 35 }; +static const unsigned int cs47l85_spk1_pins[] = { 36, 38 }; +static const unsigned int cs47l85_spk2_pins[] = { 37, 39 }; + +static const struct madera_pin_groups cs47l85_pin_groups[] = { + { "aif1", cs47l85_aif1_pins, ARRAY_SIZE(cs47l85_aif1_pins) }, + { "aif2", cs47l85_aif2_pins, ARRAY_SIZE(cs47l85_aif2_pins) }, + { "aif3", cs47l85_aif3_pins, ARRAY_SIZE(cs47l85_aif3_pins) }, + { "aif4", cs47l85_aif4_pins, ARRAY_SIZE(cs47l85_aif4_pins) }, + { "mif1", cs47l85_mif1_pins, ARRAY_SIZE(cs47l85_mif1_pins) }, + { "mif2", cs47l85_mif2_pins, ARRAY_SIZE(cs47l85_mif2_pins) }, + { "mif3", cs47l85_mif3_pins, ARRAY_SIZE(cs47l85_mif3_pins) }, + { "dmic4", cs47l85_dmic4_pins, ARRAY_SIZE(cs47l85_dmic4_pins) }, + { "dmic5", cs47l85_dmic5_pins, ARRAY_SIZE(cs47l85_dmic5_pins) }, + { "dmic6", cs47l85_dmic6_pins, ARRAY_SIZE(cs47l85_dmic6_pins) }, + { "pdmspk1", cs47l85_spk1_pins, ARRAY_SIZE(cs47l85_spk1_pins) }, + { "pdmspk2", cs47l85_spk2_pins, ARRAY_SIZE(cs47l85_spk2_pins) }, +}; + +const struct madera_pin_chip cs47l85_pin_chip = { + .n_pins = CS47L85_NUM_GPIOS, + .pin_groups = cs47l85_pin_groups, + .n_pin_groups = ARRAY_SIZE(cs47l85_pin_groups), +}; +#endif + +#ifdef CONFIG_PINCTRL_CS47L90 +/* Note - all 1 less than in datasheet because these are zero-indexed */ +static const unsigned int cs47l90_mif1_pins[] = { 8, 9 }; +static const unsigned int cs47l90_mif2_pins[] = { 10, 11 }; +static const unsigned int cs47l90_mif3_pins[] = { 12, 13 }; +static const unsigned int cs47l90_aif1_pins[] = { 14, 15, 16, 17 }; +static const unsigned int cs47l90_aif2_pins[] = { 18, 19, 20, 21 }; +static const unsigned int cs47l90_aif3_pins[] = { 22, 23, 24, 25 }; +static const unsigned int cs47l90_aif4_pins[] = { 26, 27, 28, 29 }; +static const unsigned int cs47l90_dmic4_pins[] = { 30, 31 }; +static const unsigned int cs47l90_dmic5_pins[] = { 32, 33 }; +static const unsigned int cs47l90_dmic3_pins[] = { 34, 35 }; +static const unsigned int cs47l90_spk1_pins[] = { 36, 37 }; + +static const struct madera_pin_groups cs47l90_pin_groups[] = { + { "aif1", cs47l90_aif1_pins, ARRAY_SIZE(cs47l90_aif1_pins) }, + { "aif2", cs47l90_aif2_pins, ARRAY_SIZE(cs47l90_aif2_pins) }, + { "aif3", cs47l90_aif3_pins, ARRAY_SIZE(cs47l90_aif3_pins) }, + { "aif4", cs47l90_aif4_pins, ARRAY_SIZE(cs47l90_aif4_pins) }, + { "mif1", cs47l90_mif1_pins, ARRAY_SIZE(cs47l90_mif1_pins) }, + { "mif2", cs47l90_mif2_pins, ARRAY_SIZE(cs47l90_mif2_pins) }, + { "mif3", cs47l90_mif3_pins, ARRAY_SIZE(cs47l90_mif3_pins) }, + { "dmic3", cs47l90_dmic3_pins, ARRAY_SIZE(cs47l90_dmic3_pins) }, + { "dmic4", cs47l90_dmic4_pins, ARRAY_SIZE(cs47l90_dmic4_pins) }, + { "dmic5", cs47l90_dmic5_pins, ARRAY_SIZE(cs47l90_dmic5_pins) }, + { "pdmspk1", cs47l90_spk1_pins, ARRAY_SIZE(cs47l90_spk1_pins) }, +}; + +const struct madera_pin_chip cs47l90_pin_chip = { + .n_pins = CS47L90_NUM_GPIOS, + .pin_groups = cs47l90_pin_groups, + .n_pin_groups = ARRAY_SIZE(cs47l90_pin_groups), +}; +#endif + +static int madera_get_groups_count(struct pinctrl_dev *pctldev) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + + /* Number of alt function groups plus number of single-pin groups */ + return priv->chip->n_pin_groups + priv->chip->n_pins; +} + +static const char *madera_get_group_name(struct pinctrl_dev *pctldev, + unsigned int selector) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + + if (selector < priv->chip->n_pin_groups) { + return priv->chip->pin_groups[selector].name; + } else { + selector -= priv->chip->n_pin_groups; + return madera_pin_single_group_names[selector]; + } +} + +static int madera_get_group_pins(struct pinctrl_dev *pctldev, + unsigned int selector, + const unsigned int **pins, + unsigned int *num_pins) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + + if (selector < priv->chip->n_pin_groups) { + *pins = priv->chip->pin_groups[selector].pins; + *num_pins = priv->chip->pin_groups[selector].n_pins; + } else { + /* return the dummy group for a single pin */ + selector -= priv->chip->n_pin_groups; + *pins = &madera_pin_single_group_pins[selector]; + *num_pins = 1; + } + return 0; +} + +static void madera_pin_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, + unsigned int offset) +{ + seq_puts(s, " madera-pinctrl"); +} + + +static const struct pinctrl_ops madera_pin_group_ops = { + .get_groups_count = madera_get_groups_count, + .get_group_name = madera_get_group_name, + .get_group_pins = madera_get_group_pins, + .pin_dbg_show = madera_pin_dbg_show, + .dt_node_to_map = pinconf_generic_dt_node_to_map_all, + .dt_free_map = pinctrl_utils_free_map, +}; + +static int madera_mux_get_funcs_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(madera_mux_funcs); +} + +static const char *madera_mux_get_func_name(struct pinctrl_dev *pctldev, + unsigned int selector) +{ + return madera_mux_funcs[selector].name; +} + +static int madera_mux_get_groups(struct pinctrl_dev *pctldev, + unsigned int selector, + const char * const **groups, + unsigned int * const num_groups) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + + *groups = madera_mux_funcs[selector].group_names; + + if (madera_mux_funcs[selector].func == 0) { + /* alt func always maps to a single group */ + *num_groups = 1; + } else { + /* other funcs map to all available gpio pins */ + *num_groups = priv->chip->n_pins; + } + + return 0; +} + +static int madera_mux_set_mux(struct pinctrl_dev *pctldev, + unsigned int selector, + unsigned int group) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + struct madera *madera = priv->madera; + const struct madera_pin_groups *pin_group = priv->chip->pin_groups; + unsigned int n_chip_groups = priv->chip->n_pin_groups; + const char *func_name = madera_mux_funcs[selector].name; + unsigned int reg; + int i, ret; + + dev_dbg(priv->dev, "%s selecting %u (%s) for group %u (%s)\n", + __func__, selector, func_name, group, + madera_get_group_name(pctldev, group)); + + if (madera_mux_funcs[selector].func == 0) { + /* alt func pin assignments are codec-specific */ + for (i = 0; i < n_chip_groups; ++i) { + if (strcmp(func_name, pin_group->name) == 0) + break; + + ++pin_group; + } + + if (i == n_chip_groups) + return -EINVAL; + + for (i = 0; i < pin_group->n_pins; ++i) { + reg = MADERA_GPIO1_CTRL_1 + (2 * pin_group->pins[i]); + + dev_dbg(priv->dev, "%s setting 0x%x func bits to 0\n", + __func__, reg); + + ret = regmap_update_bits(madera->regmap, reg, 0x1ff, 0); + if (ret) + break; + + } + } else { + /* + * for other funcs the group will be the gpio number and will + * be offset by the number of chip-specific functions at the + * start of the group list + */ + group -= n_chip_groups; + reg = MADERA_GPIO1_CTRL_1 + (2 * group); + + dev_dbg(priv->dev, "%s setting 0x%x func bits to 0x%x\n", + __func__, reg, madera_mux_funcs[selector].func); + + ret = regmap_update_bits(madera->regmap, + reg, + 0x1ff, + madera_mux_funcs[selector].func); + } + + if (ret) + dev_err(priv->dev, "Failed to write to 0x%x (%d)\n", + reg, ret); + + return ret; +} + +static const struct pinmux_ops madera_pin_mux_ops = { + .get_functions_count = madera_mux_get_funcs_count, + .get_function_name = madera_mux_get_func_name, + .get_function_groups = madera_mux_get_groups, + .set_mux = madera_mux_set_mux, +}; + +static unsigned int madera_pin_unmake_drv_str(struct madera_pin_private *priv, + u16 regval) +{ + regval = (regval & MADERA_GP1_DRV_STR_MASK) >> MADERA_GP1_DRV_STR_SHIFT; + + switch (priv->madera->type) { + case CS47L35: + case CS47L85: + case CS47L90: + case WM1840: + switch (regval) { + case 0: + return 4; + case 2: + return 8; + default: + return 0; + } + + default: + switch (regval) { + case 0: + return 4; + case 1: + return 8; + case 2: + return 12; + case 3: + return 16; + default: + return 0; + } + } +} + +static int madera_pin_conf_get(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *config) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + unsigned int param = pinconf_to_config_param(*config); + unsigned int result = 0; + u16 conf[2]; + int ret; + + ret = regmap_bulk_read(priv->madera->regmap, + MADERA_GPIO1_CTRL_1 + (2 * pin), + conf, 2); + if (ret) { + dev_err(priv->dev, "Failed to read GP%d conf (%d)\n", + pin + 1, ret); + return ret; + } + + switch (param) { + case PIN_CONFIG_BIAS_BUS_HOLD: + conf[1] &= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + if (conf[1] == (MADERA_GP1_PU | MADERA_GP1_PD)) + result = 1; + break; + case PIN_CONFIG_BIAS_DISABLE: + conf[1] &= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + if (!conf[1]) + result = 1; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + conf[1] &= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + if (conf[1] == MADERA_GP1_PD_MASK) + result = 1; + break; + case PIN_CONFIG_BIAS_PULL_UP: + conf[1] &= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + if (conf[1] == MADERA_GP1_PU_MASK) + result = 1; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + if (conf[0] & MADERA_GP1_OP_CFG_MASK) + result = 1; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + if (!(conf[0] & MADERA_GP1_OP_CFG_MASK)) + result = 1; + break; + case PIN_CONFIG_DRIVE_STRENGTH: + result = madera_pin_unmake_drv_str(priv, conf[1]); + break; + case PIN_CONFIG_INPUT_DEBOUNCE: + if (conf[0] & MADERA_GP1_DB_MASK) + result = 1; + break; + case PIN_CONFIG_INPUT_ENABLE: + if (conf[0] & MADERA_GP1_DIR_MASK) + result = 1; + break; + case PIN_CONFIG_INPUT_SCHMITT: + case PIN_CONFIG_INPUT_SCHMITT_ENABLE: + if (conf[0] & MADERA_GP1_IP_CFG_MASK) + result = 1; + break; + case PIN_CONFIG_OUTPUT: + if ((conf[1] & MADERA_GP1_DIR_MASK) && + (conf[0] & MADERA_GP1_LVL_MASK)) + result = 1; + break; + default: + break; + } + + *config = pinconf_to_config_packed(param, result); + + return 0; +} + +static u16 madera_pin_make_drv_str(struct madera_pin_private *priv, + unsigned int milliamps) +{ + switch (priv->madera->type) { + case CS47L35: + case CS47L85: + case CS47L90: + case WM1840: + switch (milliamps) { + case 4: + return 0; + case 8: + return 2 << MADERA_GP1_DRV_STR_SHIFT; + default: + break; + } + break; + + default: + switch (milliamps) { + case 4: + return 0; + case 8: + return 1 << MADERA_GP1_DRV_STR_SHIFT; + case 12: + return 2 << MADERA_GP1_DRV_STR_SHIFT; + case 16: + return 3 << MADERA_GP1_DRV_STR_SHIFT; + default: + break; + } + break; + } + + dev_warn(priv->dev, "%u mA not a valid drive strength", milliamps); + + return 0; +} + +static int madera_pin_conf_set(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *configs, unsigned int num_configs) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + u16 conf[2] = {0, 0}; + u16 mask[2] = {0, 0}; + unsigned int reg = MADERA_GPIO1_CTRL_1 + (2 * pin); + unsigned int val; + int ret; + + while (num_configs) { + dev_dbg(priv->dev, "%s config 0x%lx\n", __func__, *configs); + + switch (pinconf_to_config_param(*configs)) { + case PIN_CONFIG_BIAS_BUS_HOLD: + mask[1] |= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + conf[1] |= MADERA_GP1_PU | MADERA_GP1_PD; + break; + case PIN_CONFIG_BIAS_DISABLE: + mask[1] |= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + conf[1] &= ~(MADERA_GP1_PU | MADERA_GP1_PD); + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + mask[1] |= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + conf[1] |= MADERA_GP1_PD; + conf[1] &= ~MADERA_GP1_PU; + break; + case PIN_CONFIG_BIAS_PULL_UP: + mask[1] |= MADERA_GP1_PU_MASK | MADERA_GP1_PD_MASK; + conf[1] |= MADERA_GP1_PU; + conf[1] &= ~MADERA_GP1_PD; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + mask[0] |= MADERA_GP1_OP_CFG_MASK; + conf[0] |= MADERA_GP1_OP_CFG; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + mask[0] |= MADERA_GP1_OP_CFG_MASK; + conf[0] &= ~MADERA_GP1_OP_CFG; + break; + case PIN_CONFIG_DRIVE_STRENGTH: + val = pinconf_to_config_argument(*configs); + mask[1] |= MADERA_GP1_DRV_STR_MASK; + conf[1] &= ~MADERA_GP1_DRV_STR_MASK; + conf[1] |= madera_pin_make_drv_str(priv, val); + break; + case PIN_CONFIG_INPUT_DEBOUNCE: + mask[0] |= MADERA_GP1_DB_MASK; + + /* + * we can't configure debounce time per-pin so value + * is just a flag + */ + val = pinconf_to_config_argument(*configs); + if (val) + conf[0] |= MADERA_GP1_DB; + else + conf[0] &= ~MADERA_GP1_DB; + break; + case PIN_CONFIG_INPUT_ENABLE: + val = pinconf_to_config_argument(*configs); + mask[1] |= MADERA_GP1_DIR_MASK; + if (val) + conf[1] |= MADERA_GP1_DIR; + else + conf[1] &= ~MADERA_GP1_DIR; + break; + case PIN_CONFIG_INPUT_SCHMITT: + val = pinconf_to_config_argument(*configs); + mask[0] |= MADERA_GP1_IP_CFG; + if (val) + conf[0] |= MADERA_GP1_IP_CFG; + else + conf[0] &= ~MADERA_GP1_IP_CFG; + + mask[1] |= MADERA_GP1_DIR_MASK; + conf[1] |= MADERA_GP1_DIR; + break; + case PIN_CONFIG_INPUT_SCHMITT_ENABLE: + mask[0] |= MADERA_GP1_IP_CFG; + conf[0] |= MADERA_GP1_IP_CFG; + mask[1] |= MADERA_GP1_DIR_MASK; + conf[1] |= MADERA_GP1_DIR; + break; + case PIN_CONFIG_OUTPUT: + val = pinconf_to_config_argument(*configs); + mask[0] |= MADERA_GP1_LVL_MASK; + if (val) + conf[0] |= MADERA_GP1_LVL; + else + conf[0] &= ~MADERA_GP1_LVL; + + mask[1] |= MADERA_GP1_DIR_MASK; + conf[1] &= ~MADERA_GP1_DIR; + break; + default: + break; + } + + ++configs; + --num_configs; + } + + dev_dbg(priv->dev, + "%s gpio%d 0x%x:0x%x 0x%x:0x%x\n", + __func__, pin + 1, reg, conf[0], reg + 1, conf[1]); + + ret = regmap_update_bits(priv->madera->regmap, reg, mask[0], conf[0]); + if (ret) + goto err; + + ++reg; + ret = regmap_update_bits(priv->madera->regmap, reg, mask[1], conf[1]); + if (ret) + goto err; + + return 0; + +err: + dev_err(priv->dev, + "Failed to write GPIO%d conf (%d) reg 0x%x\n", + pin + 1, ret, reg); + + return ret; +} + +static int madera_pin_conf_group_set(struct pinctrl_dev *pctldev, + unsigned int selector, + unsigned long *configs, + unsigned int num_configs) +{ + struct madera_pin_private *priv = pinctrl_dev_get_drvdata(pctldev); + const struct madera_pin_groups *pin_group; + unsigned int n_groups = priv->chip->n_pin_groups; + int i, ret; + + dev_dbg(priv->dev, "%s setting group %s\n", __func__, + madera_get_group_name(pctldev, selector)); + + if (selector >= n_groups) { + /* group is a single pin, convert to pin number and set */ + return madera_pin_conf_set(pctldev, + selector - n_groups, + configs, + num_configs); + } else { + pin_group = &priv->chip->pin_groups[selector]; + + for (i = 0; i < pin_group->n_pins; ++i) { + ret = madera_pin_conf_set(pctldev, + pin_group->pins[i], + configs, + num_configs); + if (ret) + return ret; + } + } + + return 0; +} + +static const struct pinconf_ops madera_pin_conf_ops = { + .pin_config_get = madera_pin_conf_get, + .pin_config_set = madera_pin_conf_set, + .pin_config_group_set = madera_pin_conf_group_set, + +}; + +static struct pinctrl_desc madera_pin_desc = { + .name = "madera-pinctrl", + .pins = madera_pins, + .pctlops = &madera_pin_group_ops, + .pmxops = &madera_pin_mux_ops, + .confops = &madera_pin_conf_ops, + .owner = THIS_MODULE, +}; + +static int madera_pin_probe(struct platform_device *pdev) +{ + struct madera *madera = dev_get_drvdata(pdev->dev.parent); + const struct madera_pdata *pdata = dev_get_platdata(madera->dev); + struct madera_pin_private *priv; + int ret; + + BUILD_BUG_ON(ARRAY_SIZE(madera_pin_single_group_names) != + ARRAY_SIZE(madera_pin_single_group_pins)); + + dev_dbg(&pdev->dev, "%s\n", __func__); + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = &pdev->dev; + priv->madera = madera; + pdev->dev.of_node = madera->dev->of_node; + + switch (madera->type) { +#ifdef CONFIG_PINCTRL_CS47L35 + case CS47L35: + priv->chip = &cs47l35_pin_chip; + break; +#endif +#ifdef CONFIG_PINCTRL_CS47L85 + case CS47L85: + case WM1840: + priv->chip = &cs47l85_pin_chip; + break; +#endif +#ifdef CONFIG_PINCTRL_CS47L90 + case CS47L90: + case CS47L91: + priv->chip = &cs47l90_pin_chip; + break; +#endif + default: + break; + } + + if (!priv->chip) + return -ENODEV; + + madera_pin_desc.npins = priv->chip->n_pins; + + priv->pctl = devm_pinctrl_register(&pdev->dev, &madera_pin_desc, priv); + if (IS_ERR(priv->pctl)) { + ret = PTR_ERR(priv->pctl); + dev_err(priv->dev, "Failed pinctrl register (%d)\n", ret); + return ret; + } + + if (pdata) { + ret = pinctrl_register_mappings(pdata->gpio_configs, + pdata->n_gpio_configs); + dev_err(priv->dev, "Failed to register pdata mappings (%d)\n", + ret); + return ret; + } + + dev_dbg(priv->dev, "pinctrl registered\n"); + + return 0; +} + +static struct platform_driver madera_pin_driver = { + .probe = madera_pin_probe, + .driver = { + .name = "madera-pinctrl", + }, +}; + +module_platform_driver(madera_pin_driver); + +MODULE_DESCRIPTION("Madera pinctrl driver"); +MODULE_AUTHOR("Richard Fitzgerald rf@opensource.wolfsonmicro.com"); +MODULE_LICENSE("GPL v2");