The wega board has a TLV320AIC3007 connected via McASP0. In the default configuration, no external crystal is mounted. We run a system clock of 25 MHz, so we use the audio codec PLL for audio clock generation.
Signed-off-by: Stefan Müller-Klieser s.mueller-klieser@phytec.de --- arch/arm/boot/dts/am335x-wega.dtsi | 62 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi index 282f6d4..7f5f8ed 100644 --- a/arch/arm/boot/dts/am335x-wega.dtsi +++ b/arch/arm/boot/dts/am335x-wega.dtsi @@ -11,6 +11,10 @@ model = "Phytec AM335x phyBOARD-WEGA"; compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx";
+ sound: sound_iface { + compatible = "ti,da830-evm-audio"; + }; + regulators { compatible = "simple-bus";
@@ -24,6 +28,58 @@ }; };
+/* Audio */ +&am33xx_pinmux { + mcasp0_pins: pinmux_mcasp0 { + pinctrl-single,pins = < + AM33XX_IOPAD(0x9AC, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_ahclkx.mcasp0_ahclkx */ + AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */ + AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */ + AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr0.mcasp0_axr0 */ + AM33XX_IOPAD(0x9A8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr1.mcasp0_axr1 */ + >; + }; +}; + +&i2c0 { + tlv320aic3007: tlv320aic3007@18 { + compatible = "ti,tlv320aic3007"; + reg = <0x18>; + AVDD-supply = <&vcc3v3>; + IOVDD-supply = <&vcc3v3>; + DRVDD-supply = <&vcc3v3>; + DVDD-supply = <&vdig1_reg>; + status = "okay"; + }; +}; + +&mcasp0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcasp0_pins>; + op-mode = <0>; /* DAVINCI_MCASP_IIS_MODE */ + tdm-slots = <2>; + serial-dir = < + 2 1 0 0 /* # 0: INACTIVE, 1: TX, 2: RX */ + >; + tx-num-evt = <16>; + rt-num-evt = <16>; + status = "okay"; +}; + +&sound { + ti,model = "AM335x-Wega"; + ti,audio-codec = <&tlv320aic3007>; + ti,mcasp-controller = <&mcasp0>; + ti,audio-routing = + "Line Out", "LLOUT", + "Line Out", "RLOUT", + "LINE1L", "Line In", + "LINE1R", "Line In"; + clocks = <&mcasp0_fck>; + clock-names = "mclk"; + status = "okay"; +}; + /* CAN Busses */ &am33xx_pinmux { dcan1_pins: pinmux_dcan1 { @@ -99,6 +155,12 @@ status = "okay"; };
+/* Power */ +&vdig1_reg { + regulator-boot-on; + regulator-always-on; +}; + /* UARTs */ &am33xx_pinmux { uart0_pins: pinmux_uart0 {