I have set up according to the thread.... but when I attempt to play a sound file (with aplay) the program just stop ....
aplay -vvv showed the below....
Plug PCM: Linear conversion PCM (S24_3LE) Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 2 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 21844 period_size : 5461 period_time : 113770 tstamp_mode : NONE period_step : 1 avail_min : 5461 period_event : 0 start_threshold : 21844 stop_threshold : 21844 silence_threshold: 0 silence_size : 0 boundary : 1431568384 Slave: Hardware PCM card 0 'TI I2S' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S24_3LE subformat : STD channels : 2 rate : 48000 exact rate : 48000 (48000/1) msbits : 16 buffer_size : 21844 period_size : 5461 period_time : 113770 tstamp_mode : NONE period_step : 1 avail_min : 5461 period_event : 0 start_threshold : 21844 stop_threshold : 21844 silence_threshold: 0 silence_size : 0 boundary : 1431568384 appl_ptr : 0 hw_ptr : 0 Max peak (10922 samples): 0x0000001a # 0% Max peak (10922 samples): 0x0000001a # 0% Max peak (10922 samples): 0x0000001a # 0% Max peak (10922 samples): 0x00002aed ####### 33%
I have
struct snd_soc_dai_link dai_i2s[] = { { .name = "I2S", .codec_dai_name = "i2s-hifi", .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_CBM_CFM | SND_SOC_DAI_FMT_IB_NF, }
Seems like the something (maybe clock ?) is missing ???
Thx
On 12/8/2014 2:37 PM, Lars-Peter Clausen wrote:
On 12/08/2014 07:03 PM, thomas chen wrote:
Thanks for the info... so it is possible for Asoc to handle such format...
Yes, its not a special format, it is just plain and simple I2S like it is supported by the majority of all drivers/devices.
So where does one specify number of bits in a FRAME/WORD (epsecially if we were to be master instead of slave ?)
That's typically specified in the format that is used, e.g. in your case SNDRV_PCM_FORMAT_S24_3LE. This is not necessarily ideal for all cases, but has work well enough so far.
and, how does one specify number of bits to ignore (before the valid data)
There are no bits to ignore the valid data. I2S has a delay of 1 bit clock cycle between the first bit of the sample and the frame sync signal. So the data bit that is transmitted on the same clock cycle as the frame sync is actually the last bit of the previous sample. So in your case your sample has 16 valid bits followed by 8 ignored bits.
and also how many valid bits (ie size of data word) ???
You can set a snd_pcm_hw_constraint_msbits() constraint to tell userspace that only a certain amount of bits are actually going to be used.
If you are using ASoC you can do this by setting the sig_bits property on your snd_soc_dai_driver.
- Lars
Thanks...
On 12/8/2014 12:01 PM, Clemens Ladisch wrote:
thomas chen wrote:
I am working on a ALSA interface to a particular codec over I2S
the audio stream format is a bit peculiar...
there are 24 BCLK cycle between transition of FSYNC... howver, there are only 16 bit that are valid
bit 0: ignore bit 1-16: valid pcm data (MSB....LSB) bit 17-23: ignore
This is the 'original' I²S format. The format where the sample begins with the 1st BCLK usually is called left-justified (and uses the opposite FSYNC polarity).
Having ignored bits is common. (Typically, there are 32 BCLK cycles per sample.)
In ASoC, this would be SND_SOC_DAIFMT_I2S and SND_SOC_DAIFMT_LEFT_J.
Regards, Clemens
Alsa-devel mailing list Alsa-devel@alsa-project.org http://mailman.alsa-project.org/mailman/listinfo/alsa-devel