This is the initial imx-wm8962 device-tree-only machine driver working with fsl_ssi driver. More features can be added on top of it later.
Signed-off-by: Nicolin Chen b42378@freescale.com --- .../devicetree/bindings/sound/imx-audio-wm8962.txt | 61 +++ sound/soc/fsl/Kconfig | 12 + sound/soc/fsl/Makefile | 2 + sound/soc/fsl/imx-wm8962.c | 387 ++++++++++++++++++++ 4 files changed, 462 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt create mode 100644 sound/soc/fsl/imx-wm8962.c
diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt new file mode 100644 index 0000000..cb188a6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt @@ -0,0 +1,61 @@ +Freescale i.MX audio complex with WM8962 codec + +Required properties: +- compatible : "fsl,imx-audio-wm8962" +- model : The user-visible name of this sound complex +- ssi-controller : The phandle of the i.MX SSI controller +- audio-codec : The phandle of the WM8962 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names could be power + supplies, WM8962 pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + WM8962 pins: + * HPOUTL + * HPOUTR + * SPKOUTL + * SPKOUTR + * MICBIAS + * IN3R + * DMIC + * DMICDAT + + Board connectors: + * Mic Jack + * Headphone Jack + * Ext Spk + +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer + +- hp-det-gpios : The gpio port of Headphone detection. +- mic-det-gpios: The gpio port of Micphone detection. + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx6q-sabresd-wm8962", + "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "MICBIAS", "AMIC", + "IN3R", "MICBIAS", + "DMIC", "MICBIAS", + "DMICDAT", "DMIC"; + mux-int-port = <2>; + mux-ext-port = <3>; + hp-det-gpios = <&gpio7 8 1>; /* active low */ + mic-det-gpios = <&gpio1 9 1>; /* active low */ +}; diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig index 7860cc2..aa43854 100644 --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -168,6 +168,18 @@ config SND_SOC_EUKREA_TLV320 Enable I2S based access to the TLV320AIC23B codec attached to the SSI interface
+config SND_SOC_IMX_WM8962 + tristate "SoC Audio support for i.MX boards with wm8962" + depends on OF && I2C + select SND_SOC_WM8962 + select SND_SOC_IMX_PCM_DMA + select SND_SOC_IMX_AUDMUX + select SND_SOC_FSL_SSI + select SND_SOC_FSL_UTILS + help + Say Y if you want to add support for SoC audio on an i.MX board with + a wm8962 codec. + config SND_SOC_IMX_SGTL5000 tristate "SoC Audio support for i.MX boards with sgtl5000" depends on OF && I2C diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile index 91883f8..d4b4aa8 100644 --- a/sound/soc/fsl/Makefile +++ b/sound/soc/fsl/Makefile @@ -42,6 +42,7 @@ snd-soc-phycore-ac97-objs := phycore-ac97.o snd-soc-mx27vis-aic32x4-objs := mx27vis-aic32x4.o snd-soc-wm1133-ev1-objs := wm1133-ev1.o snd-soc-imx-sgtl5000-objs := imx-sgtl5000.o +snd-soc-imx-wm8962-objs := imx-wm8962.o snd-soc-imx-mc13783-objs := imx-mc13783.o
obj-$(CONFIG_SND_SOC_EUKREA_TLV320) += snd-soc-eukrea-tlv320.o @@ -49,4 +50,5 @@ obj-$(CONFIG_SND_SOC_PHYCORE_AC97) += snd-soc-phycore-ac97.o obj-$(CONFIG_SND_SOC_MX27VIS_AIC32X4) += snd-soc-mx27vis-aic32x4.o obj-$(CONFIG_SND_MXC_SOC_WM1133_EV1) += snd-soc-wm1133-ev1.o obj-$(CONFIG_SND_SOC_IMX_SGTL5000) += snd-soc-imx-sgtl5000.o +obj-$(CONFIG_SND_SOC_IMX_WM8962) += snd-soc-imx-wm8962.o obj-$(CONFIG_SND_SOC_IMX_MC13783) += snd-soc-imx-mc13783.o diff --git a/sound/soc/fsl/imx-wm8962.c b/sound/soc/fsl/imx-wm8962.c new file mode 100644 index 0000000..7aa42d8 --- /dev/null +++ b/sound/soc/fsl/imx-wm8962.c @@ -0,0 +1,387 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Based on imx-sgtl5000.c + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2012 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/of_i2c.h> +#include <linux/of_gpio.h> +#include <linux/slab.h> +#include <linux/clk.h> +#include <linux/irq.h> +#include <sound/soc.h> +#include <sound/pcm_params.h> +#include <sound/soc-dapm.h> +#include <linux/pinctrl/consumer.h> + +#include "../codecs/wm8962.h" +#include "imx-audmux.h" + +#define DAI_NAME_SIZE 32 + +struct imx_wm8962_data { + struct snd_soc_dai_link dai; + struct snd_soc_card card; + char codec_dai_name[DAI_NAME_SIZE]; + char platform_name[DAI_NAME_SIZE]; + struct clk *codec_clk; + unsigned int clk_frequency; +}; + +struct imx_priv { + int hp_gpio; + int hp_active_low; + int hp_status; + int amic_gpio; + int amic_active_low; + int amic_status; + struct platform_device *pdev; + struct snd_pcm_substream *first_stream; + struct snd_pcm_substream *second_stream; +}; +static struct imx_priv card_priv; + +static const struct snd_soc_dapm_widget imx_wm8962_dapm_widgets[] = { + SND_SOC_DAPM_HP("Headphone Jack", NULL), + SND_SOC_DAPM_SPK("Ext Spk", NULL), + SND_SOC_DAPM_MIC("AMIC", NULL), + SND_SOC_DAPM_MIC("DMIC", NULL), +}; + +static int check_hw_params(struct snd_pcm_substream *substream, + snd_pcm_format_t sample_format, unsigned int sample_rate) +{ + struct imx_priv *priv = &card_priv; + struct device *dev = substream->pcm->card->dev; + + substream->runtime->sample_bits = + snd_pcm_format_physical_width(sample_format); + substream->runtime->rate = sample_rate; + substream->runtime->format = sample_format; + + if (!priv->first_stream) { + priv->first_stream = substream; + } else { + priv->second_stream = substream; + + if (priv->first_stream->runtime->rate != + priv->second_stream->runtime->rate) { + dev_err(dev, "KEEP THE SAME SAMPLE RATE: %d!\n", + priv->first_stream->runtime->rate); + return -EINVAL; + } + if (priv->first_stream->runtime->sample_bits != + priv->second_stream->runtime->sample_bits) { + snd_pcm_format_t first_format = + priv->first_stream->runtime->format; + + dev_err(dev, "KEEP THE SAME FORMAT: %s!\n", + snd_pcm_format_name(first_format)); + return -EINVAL; + } + } + + return 0; +} + +static int imx_hifi_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct snd_soc_dai *codec_dai = rtd->codec_dai; + struct device *dev = substream->pcm->card->dev; + struct imx_priv *priv = &card_priv; + struct imx_wm8962_data *data = platform_get_drvdata(priv->pdev); + unsigned int sample_rate = params_rate(params); + unsigned int sample_format = params_format(params); + int ret = 0; + unsigned int pll_out; + + /* + * WM8962 doesn't support two substreams in different sample rates or + * sample formats. So check the two parameters of two substreams' when + * there're two substreams of playback and of capture in the same time. + */ + ret = check_hw_params(substream, sample_format, sample_rate); + if (ret < 0) { + dev_err(dev, "Failed to match hw params: %d\n", ret); + return ret; + } + + if (sample_format == SNDRV_PCM_FORMAT_S24_LE) + pll_out = sample_rate * 384; + else + pll_out = sample_rate * 256; + + ret = snd_soc_dai_set_pll(codec_dai, WM8962_FLL, WM8962_FLL_MCLK, + data->clk_frequency, pll_out); + if (ret < 0) { + dev_err(dev, "Failed to start FLL: %d\n", ret); + return ret; + } + + ret = snd_soc_dai_set_sysclk(codec_dai, WM8962_SYSCLK_FLL, + pll_out, SND_SOC_CLOCK_IN); + if (ret < 0) { + dev_err(dev, "Failed to set SYSCLK: %d\n", ret); + return ret; + } + + return 0; +} + +static int imx_hifi_hw_free(struct snd_pcm_substream *substream) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct snd_soc_dai *codec_dai = rtd->codec_dai; + struct device *dev = substream->pcm->card->dev; + struct imx_priv *priv = &card_priv; + struct imx_wm8962_data *data = platform_get_drvdata(priv->pdev); + int ret; + + /* We don't need to handle anything if there's no substream running */ + if (!priv->first_stream) + return 0; + + if (priv->first_stream == substream) + priv->first_stream = priv->second_stream; + priv->second_stream = NULL; + + if (!priv->first_stream) { + /* + * SYSCLK of wm8962's not disabled yet. If we wanna close FLL, + * we need to keep SYSCLK alive by changing its source to MCLK. + */ + ret = snd_soc_dai_set_sysclk(codec_dai, WM8962_SYSCLK_MCLK, + data->clk_frequency, SND_SOC_CLOCK_IN); + if (ret < 0) { + dev_err(dev, "Failed to set SYSCLK: %d\n", ret); + return ret; + } + + /* Disable FLL and let codec do pm_runtime_put() */ + ret = snd_soc_dai_set_pll(codec_dai, WM8962_FLL, 0, 0, 0); + if (ret < 0) { + dev_err(dev, "Failed to disable FLL: %d\n", ret); + return ret; + } + } + + return 0; +} + +static struct snd_soc_ops imx_hifi_ops = { + .hw_params = imx_hifi_hw_params, + .hw_free = imx_hifi_hw_free, +}; + +static int imx_wm8962_late_probe(struct snd_soc_card *card) +{ + struct snd_soc_dai *codec_dai = card->rtd[0].codec_dai; + struct imx_priv *priv = &card_priv; + struct imx_wm8962_data *data = platform_get_drvdata(priv->pdev); + int ret; + + ret = snd_soc_dai_set_sysclk(codec_dai, WM8962_SYSCLK_MCLK, + data->clk_frequency, SND_SOC_CLOCK_IN); + if (ret < 0) + dev_err(card->dev, "Failed to set sysclk in %s\n", __func__); + + return ret; +} + +static int imx_wm8962_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct device_node *ssi_np, *codec_np; + struct platform_device *ssi_pdev; + struct imx_priv *priv = &card_priv; + struct i2c_client *codec_dev; + struct imx_wm8962_data *data; + int int_port, ext_port; + int ret; + + priv->pdev = pdev; + + ret = of_property_read_u32(np, "mux-int-port", &int_port); + if (ret) { + dev_err(&pdev->dev, "mux-int-port missing or invalid\n"); + return ret; + } + ret = of_property_read_u32(np, "mux-ext-port", &ext_port); + if (ret) { + dev_err(&pdev->dev, "mux-ext-port missing or invalid\n"); + return ret; + } + + /* + * The port numbering in the hardware manual starts at 1, while + * the audmux API expects it starts at 0. + */ + int_port--; + ext_port--; + ret = imx_audmux_v2_configure_port(int_port, + IMX_AUDMUX_V2_PTCR_SYN | + IMX_AUDMUX_V2_PTCR_TFSEL(ext_port) | + IMX_AUDMUX_V2_PTCR_TCSEL(ext_port) | + IMX_AUDMUX_V2_PTCR_TFSDIR | + IMX_AUDMUX_V2_PTCR_TCLKDIR, + IMX_AUDMUX_V2_PDCR_RXDSEL(ext_port)); + if (ret) { + dev_err(&pdev->dev, "audmux internal port setup failed\n"); + return ret; + } + imx_audmux_v2_configure_port(ext_port, + IMX_AUDMUX_V2_PTCR_SYN, + IMX_AUDMUX_V2_PDCR_RXDSEL(int_port)); + if (ret) { + dev_err(&pdev->dev, "audmux external port setup failed\n"); + return ret; + } + + ssi_np = of_parse_phandle(pdev->dev.of_node, "ssi-controller", 0); + codec_np = of_parse_phandle(pdev->dev.of_node, "audio-codec", 0); + if (!ssi_np || !codec_np) { + dev_err(&pdev->dev, "phandle missing or invalid\n"); + ret = -EINVAL; + goto fail; + } + + ssi_pdev = of_find_device_by_node(ssi_np); + if (!ssi_pdev) { + dev_err(&pdev->dev, "failed to find SSI platform device\n"); + ret = -EINVAL; + goto fail; + } + codec_dev = of_find_i2c_device_by_node(codec_np); + if (!codec_dev || !codec_dev->driver) { + dev_err(&pdev->dev, "failed to find codec platform device\n"); + return -EINVAL; + } + + priv->hp_gpio = of_get_named_gpio_flags(np, "hp-det-gpios", 0, + (enum of_gpio_flags *)&priv->hp_active_low); + priv->amic_gpio = of_get_named_gpio_flags(np, "mic-det-gpios", 0, + (enum of_gpio_flags *)&priv->amic_active_low); + + priv->first_stream = NULL; + priv->second_stream = NULL; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) { + ret = -ENOMEM; + goto fail; + } + + data->codec_clk = clk_get(&codec_dev->dev, NULL); + if (IS_ERR(data->codec_clk)) { + /* assuming clock enabled by default */ + data->codec_clk = NULL; + ret = of_property_read_u32(codec_np, "clock-frequency", + &data->clk_frequency); + if (ret) { + dev_err(&codec_dev->dev, + "clock-frequency missing or invalid\n"); + goto fail; + } + } else { + data->clk_frequency = clk_get_rate(data->codec_clk); + clk_prepare_enable(data->codec_clk); + } + + data->dai.name = "HiFi"; + data->dai.stream_name = "HiFi"; + data->dai.codec_dai_name = "wm8962"; + data->dai.codec_of_node = codec_np; + data->dai.cpu_dai_name = dev_name(&ssi_pdev->dev); + data->dai.platform_of_node = ssi_np; + data->dai.ops = &imx_hifi_ops, + data->dai.dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | + SND_SOC_DAIFMT_CBM_CFM; + + data->card.dev = &pdev->dev; + ret = snd_soc_of_parse_card_name(&data->card, "model"); + if (ret) + goto clk_fail; + ret = snd_soc_of_parse_audio_routing(&data->card, "audio-routing"); + if (ret) + goto clk_fail; + data->card.num_links = 1; + data->card.dai_link = &data->dai; + data->card.dapm_widgets = imx_wm8962_dapm_widgets; + data->card.num_dapm_widgets = ARRAY_SIZE(imx_wm8962_dapm_widgets); + + data->card.late_probe = imx_wm8962_late_probe, + + ret = snd_soc_register_card(&data->card); + if (ret) { + dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret); + goto clk_fail; + } + + platform_set_drvdata(pdev, data); + of_node_put(ssi_np); + of_node_put(codec_np); + + return 0; + +clk_fail: + if (data->codec_clk) { + clk_disable_unprepare(data->codec_clk); + clk_put(data->codec_clk); + } +fail: + if (ssi_np) + of_node_put(ssi_np); + if (codec_np) + of_node_put(codec_np); + + return ret; +} + +static int imx_wm8962_remove(struct platform_device *pdev) +{ + struct imx_wm8962_data *data = platform_get_drvdata(pdev); + + if (data->codec_clk) { + clk_disable_unprepare(data->codec_clk); + clk_put(data->codec_clk); + } + snd_soc_unregister_card(&data->card); + + return 0; +} + +static const struct of_device_id imx_wm8962_dt_ids[] = { + { .compatible = "fsl,imx-audio-wm8962", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, imx_wm8962_dt_ids); + +static struct platform_driver imx_wm8962_driver = { + .driver = { + .name = "imx-wm8962", + .owner = THIS_MODULE, + .of_match_table = imx_wm8962_dt_ids, + }, + .probe = imx_wm8962_probe, + .remove = imx_wm8962_remove, +}; +module_platform_driver(imx_wm8962_driver); + +MODULE_AUTHOR("Freescale Semiconductor, Inc."); +MODULE_DESCRIPTION("Freescale i.MX WM8962 ASoC machine driver"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:imx-wm8962");