Move the DICE interface symbols into a separate header file, and add more documentation.
Signed-off-by: Clemens Ladisch clemens@ladisch.de --- sound/firewire/dice-interface.h | 371 +++++++++++++++++++++++++++++++++++++++ sound/firewire/dice.c | 209 ---------------------- 2 files changed, 373 insertions(+), 207 deletions(-) create mode 100644 sound/firewire/dice-interface.h
diff --git a/sound/firewire/dice-interface.h b/sound/firewire/dice-interface.h new file mode 100644 index 0000000..af916b9 --- /dev/null +++ b/sound/firewire/dice-interface.h @@ -0,0 +1,371 @@ +#ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED +#define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED + +/* + * DICE device interface definitions + */ + +/* + * Generally, all registers can be read like memory, i.e., with quadlet read or + * block read transactions with any alignment or length. Writes are not + * allowed except where noted; quadlet-sized registers must be written with + * a quadlet write transaction. + * + * All values are in big endian. The DICE firmware runs on a little-endian CPU + * and just byte-swaps _all_ quadlets on the bus, so values without endianness + * (e.g. strings) get scrambled and must be byte-swapped again by the driver. + */ + +/* + * Streaming is handled by the "DICE driver" interface. Its registers are + * located in this private address space. + */ +#define DICE_PRIVATE_SPACE 0xffffe0000000uLL + +/* + * The registers are organized in several sections, which are organized + * separately to allow them to be extended individually. Whether a register is + * supported can be detected by checking its offset against its section's size. + * + * The section offset values are relative to DICE_PRIVATE_SPACE; the offset/ + * size values are measured in quadlets. Read-only. + */ +#define DICE_GLOBAL_OFFSET 0x00 +#define DICE_GLOBAL_SIZE 0x04 +#define DICE_TX_OFFSET 0x08 +#define DICE_TX_SIZE 0x0c +#define DICE_RX_OFFSET 0x10 +#define DICE_RX_SIZE 0x14 +#define DICE_EXT_SYNC_OFFSET 0x18 +#define DICE_EXT_SYNC_SIZE 0x1c +#define DICE_UNUSED2_OFFSET 0x20 +#define DICE_UNUSED2_SIZE 0x24 + +/* + * Global settings. + */ + +/* + * Stores the full 64-bit address (node ID and offset in the node's address + * space) where the device will send notifications. Must be changed with + * a compare/swap transaction by the owner. This register is automatically + * cleared on a bus reset. + */ +#define GLOBAL_OWNER 0x000 +#define OWNER_NO_OWNER 0xffff000000000000uLL +#define OWNER_NODE_SHIFT 48 + +/* + * A bitmask with asynchronous events; read-only. When any event(s) happen, + * the bits of previous events are cleared, and the value of this register is + * also written to the address stored in the owner register. + */ +#define GLOBAL_NOTIFICATION 0x008 +/* Some registers in the Rx/Tx sections may have changed. */ +#define NOTIFY_RX_CFG_CHG 0x00000001 +#define NOTIFY_TX_CFG_CHG 0x00000002 +/* Lock status of the current clock source may have changed. */ +#define NOTIFY_LOCK_CHG 0x00000010 +/* Write to the clock select register has been finished. */ +#define NOTIFY_CLOCK_ACCEPTED 0x00000020 +/* Lock status of some clock source has changed. */ +#define NOTIFY_EXT_STATUS 0x00000040 +/* Other bits may be used for device-specific events. */ + +/* + * A name that can be customized for each device; read/write. Padded with zero + * bytes. Quadlets are byte-swapped. The encoding is whatever the host driver + * happens to be using. + */ +#define GLOBAL_NICK_NAME 0x00c +#define NICK_NAME_SIZE 64 + +/* + * The current sample rate and clock source; read/write. Whether a clock + * source or sample rate is supported is device-specific; the internal clock + * source is always available. Low/mid/high = up to 48/96/192 kHz. This + * register can be changed even while streams are running. + */ +#define GLOBAL_CLOCK_SELECT 0x04c +#define CLOCK_SOURCE_MASK 0x000000ff +#define CLOCK_SOURCE_AES1 0x00000000 +#define CLOCK_SOURCE_AES2 0x00000001 +#define CLOCK_SOURCE_AES3 0x00000002 +#define CLOCK_SOURCE_AES4 0x00000003 +#define CLOCK_SOURCE_AES_ANY 0x00000004 +#define CLOCK_SOURCE_ADAT 0x00000005 +#define CLOCK_SOURCE_TDIF 0x00000006 +#define CLOCK_SOURCE_WC 0x00000007 +#define CLOCK_SOURCE_ARX1 0x00000008 +#define CLOCK_SOURCE_ARX2 0x00000009 +#define CLOCK_SOURCE_ARX3 0x0000000a +#define CLOCK_SOURCE_ARX4 0x0000000b +#define CLOCK_SOURCE_INTERNAL 0x0000000c +#define CLOCK_RATE_MASK 0x0000ff00 +#define CLOCK_RATE_32000 0x00000000 +#define CLOCK_RATE_44100 0x00000100 +#define CLOCK_RATE_48000 0x00000200 +#define CLOCK_RATE_88200 0x00000300 +#define CLOCK_RATE_96000 0x00000400 +#define CLOCK_RATE_176400 0x00000500 +#define CLOCK_RATE_192000 0x00000600 +#define CLOCK_RATE_ANY_LOW 0x00000700 +#define CLOCK_RATE_ANY_MID 0x00000800 +#define CLOCK_RATE_ANY_HIGH 0x00000900 +#define CLOCK_RATE_NONE 0x00000a00 +#define CLOCK_RATE_SHIFT 8 + +/* + * Enable streaming; read/write. Writing a non-zero value (re)starts all + * streams that have a valid iso channel set; zero stops all streams. The + * streams' parameters must be configured before starting. This register is + * automatically cleared on a bus reset. + */ +#define GLOBAL_ENABLE 0x050 + +/* + * Status of the sample clock; read-only. + */ +#define GLOBAL_STATUS 0x054 +/* The current clock source is locked. */ +#define STATUS_SOURCE_LOCKED 0x00000001 +/* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */ +#define STATUS_NOMINAL_RATE_MASK 0x0000ff00 + +/* + * Status of all clock sources; read-only. + */ +#define GLOBAL_EXTENDED_STATUS 0x058 +/* + * The _LOCKED bits always show the current status; any change generates + * a notification. + */ +#define EXT_STATUS_AES1_LOCKED 0x00000001 +#define EXT_STATUS_AES2_LOCKED 0x00000002 +#define EXT_STATUS_AES3_LOCKED 0x00000004 +#define EXT_STATUS_AES4_LOCKED 0x00000008 +#define EXT_STATUS_ADAT_LOCKED 0x00000010 +#define EXT_STATUS_TDIF_LOCKED 0x00000020 +#define EXT_STATUS_ARX1_LOCKED 0x00000040 +#define EXT_STATUS_ARX2_LOCKED 0x00000080 +#define EXT_STATUS_ARX3_LOCKED 0x00000100 +#define EXT_STATUS_ARX4_LOCKED 0x00000200 +#define EXT_STATUS_WC_LOCKED 0x00000400 +/* + * The _SLIP bits do not generate notifications; a set bit indicates that an + * error occurred since the last time when this register was read with + * a quadlet read transaction. + */ +#define EXT_STATUS_AES1_SLIP 0x00010000 +#define EXT_STATUS_AES2_SLIP 0x00020000 +#define EXT_STATUS_AES3_SLIP 0x00040000 +#define EXT_STATUS_AES4_SLIP 0x00080000 +#define EXT_STATUS_ADAT_SLIP 0x00100000 +#define EXT_STATUS_TDIF_SLIP 0x00200000 +#define EXT_STATUS_ARX1_SLIP 0x00400000 +#define EXT_STATUS_ARX2_SLIP 0x00800000 +#define EXT_STATUS_ARX3_SLIP 0x01000000 +#define EXT_STATUS_ARX4_SLIP 0x02000000 +#define EXT_STATUS_WC_SLIP 0x04000000 + +/* + * The measured rate of the current clock source, in Hz; read-only. + */ +#define GLOBAL_SAMPLE_RATE 0x05c + +/* + * The version of the DICE driver specification that this device conforms to; + * read-only. + */ +#define GLOBAL_VERSION 0x060 + +/* Some old firmware versions do not have the following global registers: */ + +/* + * Supported sample rates and clock sources; read-only. + */ +#define GLOBAL_CLOCK_CAPABILITIES 0x064 +#define CLOCK_CAP_RATE_32000 0x00000001 +#define CLOCK_CAP_RATE_44100 0x00000002 +#define CLOCK_CAP_RATE_48000 0x00000004 +#define CLOCK_CAP_RATE_88200 0x00000008 +#define CLOCK_CAP_RATE_96000 0x00000010 +#define CLOCK_CAP_RATE_176400 0x00000020 +#define CLOCK_CAP_RATE_192000 0x00000040 +#define CLOCK_CAP_SOURCE_AES1 0x00010000 +#define CLOCK_CAP_SOURCE_AES2 0x00020000 +#define CLOCK_CAP_SOURCE_AES3 0x00040000 +#define CLOCK_CAP_SOURCE_AES4 0x00080000 +#define CLOCK_CAP_SOURCE_AES_ANY 0x00100000 +#define CLOCK_CAP_SOURCE_ADAT 0x00200000 +#define CLOCK_CAP_SOURCE_TDIF 0x00400000 +#define CLOCK_CAP_SOURCE_WC 0x00800000 +#define CLOCK_CAP_SOURCE_ARX1 0x01000000 +#define CLOCK_CAP_SOURCE_ARX2 0x02000000 +#define CLOCK_CAP_SOURCE_ARX3 0x04000000 +#define CLOCK_CAP_SOURCE_ARX4 0x08000000 +#define CLOCK_CAP_SOURCE_INTERNAL 0x10000000 + +/* + * Names of all clock sources; read-only. Quadlets are byte-swapped. Names + * are separated with one backslash, the list is terminated with two + * backslashes. Unused clock sources are included. + */ +#define GLOBAL_CLOCK_SOURCE_NAMES 0x068 +#define CLOCK_SOURCE_NAMES_SIZE 256 + +/* + * Capture stream settings. This section includes the number/size registers + * and the registers of all streams. + */ + +/* + * The number of supported capture streams; read-only. + */ +#define TX_NUMBER 0x000 + +/* + * The size of one stream's register block, in quadlets; read-only. The + * registers of the first stream follow immediately afterwards; the registers + * of the following streams are offset by this register's value. + */ +#define TX_SIZE 0x004 + +/* + * The isochronous channel number on which packets are sent, or -1 if the + * stream is not to be used; read/write. + */ +#define TX_ISOCHRONOUS 0x008 + +/* + * The number of audio channels; read-only. There will be one quadlet per + * channel; the first channel is the first quadlet in a data block. + */ +#define TX_NUMBER_AUDIO 0x00c + +/* + * The number of MIDI ports, 0-8; read-only. If > 0, there will be one + * additional quadlet in each data block, following the audio quadlets. + */ +#define TX_NUMBER_MIDI 0x010 + +/* + * The speed at which the packets are sent, SCODE_100-_400; read/write. + */ +#define TX_SPEED 0x014 + +/* + * Names of all audio channels; read-only. Quadlets are byte-swapped. Names + * are separated with one backslash, the list is terminated with two + * backslashes. + */ +#define TX_NAMES 0x018 +#define TX_NAMES_SIZE 256 + +/* + * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio + * channel. + */ +#define TX_AC3_CAPABILITIES 0x118 + +/* + * Send audio data with IEC60958 label; read/write. Bitmask with one bit per + * audio channel. This register can be changed even while the stream is + * running. + */ +#define TX_AC3_ENABLE 0x11c + +/* + * Playback stream settings. This section includes the number/size registers + * and the registers of all streams. + */ + +/* + * The number of supported playback streams; read-only. + */ +#define RX_NUMBER 0x000 + +/* + * The size of one stream's register block, in quadlets; read-only. The + * registers of the first stream follow immediately afterwards; the registers + * of the following streams are offset by this register's value. + */ +#define RX_SIZE 0x004 + +/* + * The isochronous channel number on which packets are received, or -1 if the + * stream is not to be used; read/write. + */ +#define RX_ISOCHRONOUS 0x008 + +/* + * Index of first quadlet to be interpreted; read/write. If > 0, that many + * quadlets at the beginning of each data block will be ignored, and all the + * audio and MIDI quadlets will follow. + */ +#define RX_SEQ_START 0x00c + +/* + * The number of audio channels; read-only. There will be one quadlet per + * channel. + */ +#define RX_NUMBER_AUDIO 0x010 + +/* + * The number of MIDI ports, 0-8; read-only. If > 0, there will be one + * additional quadlet in each data block, following the audio quadlets. + */ +#define RX_NUMBER_MIDI 0x014 + +/* + * Names of all audio channels; read-only. Quadlets are byte-swapped. Names + * are separated with one backslash, the list is terminated with two + * backslashes. + */ +#define RX_NAMES 0x018 +#define RX_NAMES_SIZE 256 + +/* + * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio + * channel. + */ +#define RX_AC3_CAPABILITIES 0x118 + +/* + * Receive audio data with IEC60958 label; read/write. Bitmask with one bit + * per audio channel. This register can be changed even while the stream is + * running. + */ +#define RX_AC3_ENABLE 0x11c + +/* + * Extended synchronization information. + * This section can be read completely with a block read request. + */ + +/* + * Current clock source; read-only. + */ +#define EXT_SYNC_CLOCK_SOURCE 0x000 + +/* + * Clock source is locked (boolean); read-only. + */ +#define EXT_SYNC_LOCKED 0x004 + +/* + * Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or + * _NONE; read-only. + */ +#define EXT_SYNC_RATE 0x008 + +/* + * ADAT user data bits; read-only. + */ +#define EXT_SYNC_ADAT_USER_DATA 0x00c +/* The data bits, if available. */ +#define ADAT_USER_DATA_MASK 0x0f +/* The data bits are not available. */ +#define ADAT_USER_DATA_NO_DATA 0x10 + +#endif diff --git a/sound/firewire/dice.c b/sound/firewire/dice.c index 3591aeb..1da1dde 100644 --- a/sound/firewire/dice.c +++ b/sound/firewire/dice.c @@ -26,212 +26,7 @@ #include "amdtp.h" #include "iso-resources.h" #include "lib.h" - -#define DICE_PRIVATE_SPACE 0xffffe0000000uLL - -/* offset from DICE_PRIVATE_SPACE; offsets and sizes in quadlets */ -#define DICE_GLOBAL_OFFSET 0x00 -#define DICE_GLOBAL_SIZE 0x04 -#define DICE_TX_OFFSET 0x08 -#define DICE_TX_SIZE 0x0c -#define DICE_RX_OFFSET 0x10 -#define DICE_RX_SIZE 0x14 - -/* pointed to by DICE_GLOBAL_OFFSET */ -#define GLOBAL_OWNER 0x000 -#define OWNER_NO_OWNER 0xffff000000000000uLL -#define OWNER_NODE_SHIFT 48 -#define GLOBAL_NOTIFICATION 0x008 -#define NOTIFY_RX_CFG_CHG 0x00000001 -#define NOTIFY_TX_CFG_CHG 0x00000002 -#define NOTIFY_DUP_ISOC 0x00000004 -#define NOTIFY_BW_ERR 0x00000008 -#define NOTIFY_LOCK_CHG 0x00000010 -#define NOTIFY_CLOCK_ACCEPTED 0x00000020 -#define NOTIFY_INTERFACE_CHG 0x00000040 -#define NOTIFY_MESSAGE 0x00100000 -#define GLOBAL_NICK_NAME 0x00c -#define NICK_NAME_SIZE 64 -#define GLOBAL_CLOCK_SELECT 0x04c -#define CLOCK_SOURCE_MASK 0x000000ff -#define CLOCK_SOURCE_AES1 0x00000000 -#define CLOCK_SOURCE_AES2 0x00000001 -#define CLOCK_SOURCE_AES3 0x00000002 -#define CLOCK_SOURCE_AES4 0x00000003 -#define CLOCK_SOURCE_AES_ANY 0x00000004 -#define CLOCK_SOURCE_ADAT 0x00000005 -#define CLOCK_SOURCE_TDIF 0x00000006 -#define CLOCK_SOURCE_WC 0x00000007 -#define CLOCK_SOURCE_ARX1 0x00000008 -#define CLOCK_SOURCE_ARX2 0x00000009 -#define CLOCK_SOURCE_ARX3 0x0000000a -#define CLOCK_SOURCE_ARX4 0x0000000b -#define CLOCK_SOURCE_INTERNAL 0x0000000c -#define CLOCK_RATE_MASK 0x0000ff00 -#define CLOCK_RATE_32000 0x00000000 -#define CLOCK_RATE_44100 0x00000100 -#define CLOCK_RATE_48000 0x00000200 -#define CLOCK_RATE_88200 0x00000300 -#define CLOCK_RATE_96000 0x00000400 -#define CLOCK_RATE_176400 0x00000500 -#define CLOCK_RATE_192000 0x00000600 -#define CLOCK_RATE_ANY_LOW 0x00000700 -#define CLOCK_RATE_ANY_MID 0x00000800 -#define CLOCK_RATE_ANY_HIGH 0x00000900 -#define CLOCK_RATE_NONE 0x00000a00 -#define CLOCK_RATE_SHIFT 8 -#define GLOBAL_ENABLE 0x050 -#define ENABLE 0x00000001 -#define GLOBAL_STATUS 0x054 -#define STATUS_SOURCE_LOCKED 0x00000001 -#define STATUS_RATE_CONFLICT 0x00000002 -#define STATUS_NOMINAL_RATE_MASK 0x0000ff00 -#define GLOBAL_EXTENDED_STATUS 0x058 -#define EXT_STATUS_AES1_LOCKED 0x00000001 -#define EXT_STATUS_AES2_LOCKED 0x00000002 -#define EXT_STATUS_AES3_LOCKED 0x00000004 -#define EXT_STATUS_AES4_LOCKED 0x00000008 -#define EXT_STATUS_ADAT_LOCKED 0x00000010 -#define EXT_STATUS_TDIF_LOCKED 0x00000020 -#define EXT_STATUS_ARX1_LOCKED 0x00000040 -#define EXT_STATUS_ARX2_LOCKED 0x00000080 -#define EXT_STATUS_ARX3_LOCKED 0x00000100 -#define EXT_STATUS_ARX4_LOCKED 0x00000200 -#define EXT_STATUS_WC_LOCKED 0x00000400 -#define EXT_STATUS_AES1_SLIP 0x00010000 -#define EXT_STATUS_AES2_SLIP 0x00020000 -#define EXT_STATUS_AES3_SLIP 0x00040000 -#define EXT_STATUS_AES4_SLIP 0x00080000 -#define EXT_STATUS_ADAT_SLIP 0x00100000 -#define EXT_STATUS_TDIF_SLIP 0x00200000 -#define EXT_STATUS_ARX1_SLIP 0x00400000 -#define EXT_STATUS_ARX2_SLIP 0x00800000 -#define EXT_STATUS_ARX3_SLIP 0x01000000 -#define EXT_STATUS_ARX4_SLIP 0x02000000 -#define EXT_STATUS_WC_SLIP 0x04000000 -#define GLOBAL_SAMPLE_RATE 0x05c -#define GLOBAL_VERSION 0x060 -#define GLOBAL_CLOCK_CAPABILITIES 0x064 -#define CLOCK_CAP_RATE_32000 0x00000001 -#define CLOCK_CAP_RATE_44100 0x00000002 -#define CLOCK_CAP_RATE_48000 0x00000004 -#define CLOCK_CAP_RATE_88200 0x00000008 -#define CLOCK_CAP_RATE_96000 0x00000010 -#define CLOCK_CAP_RATE_176400 0x00000020 -#define CLOCK_CAP_RATE_192000 0x00000040 -#define CLOCK_CAP_SOURCE_AES1 0x00010000 -#define CLOCK_CAP_SOURCE_AES2 0x00020000 -#define CLOCK_CAP_SOURCE_AES3 0x00040000 -#define CLOCK_CAP_SOURCE_AES4 0x00080000 -#define CLOCK_CAP_SOURCE_AES_ANY 0x00100000 -#define CLOCK_CAP_SOURCE_ADAT 0x00200000 -#define CLOCK_CAP_SOURCE_TDIF 0x00400000 -#define CLOCK_CAP_SOURCE_WC 0x00800000 -#define CLOCK_CAP_SOURCE_ARX1 0x01000000 -#define CLOCK_CAP_SOURCE_ARX2 0x02000000 -#define CLOCK_CAP_SOURCE_ARX3 0x04000000 -#define CLOCK_CAP_SOURCE_ARX4 0x08000000 -#define CLOCK_CAP_SOURCE_INTERNAL 0x10000000 -#define GLOBAL_CLOCK_SOURCE_NAMES 0x068 -#define CLOCK_SOURCE_NAMES_SIZE 256 - -/* pointed to by DICE_TX_OFFSET */ -#define TX_NUMBER 0x000 -#define TX_SIZE 0x004 -/* repeated TX_NUMBER times, offset by TX_SIZE quadlets */ -#define TX_ISOCHRONOUS 0x008 -#define TX_NUMBER_AUDIO 0x00c -#define TX_NUMBER_MIDI 0x010 -#define TX_SPEED 0x014 -#define TX_NAMES 0x018 -#define TX_NAMES_SIZE 256 -#define TX_AC3_CAPABILITIES 0x118 -#define TX_AC3_ENABLE 0x11c - -/* pointed to by DICE_RX_OFFSET */ -#define RX_NUMBER 0x000 -#define RX_SIZE 0x004 -/* repeated RX_NUMBER times, offset by RX_SIZE quadlets */ -#define RX_ISOCHRONOUS 0x008 -#define RX_SEQ_START 0x00c -#define RX_NUMBER_AUDIO 0x010 -#define RX_NUMBER_MIDI 0x014 -#define RX_NAMES 0x018 -#define RX_NAMES_SIZE 256 -#define RX_AC3_CAPABILITIES 0x118 -#define RX_AC3_ENABLE 0x11c - - -#define FIRMWARE_LOAD_SPACE 0xffffe0100000uLL - -/* offset from FIRMWARE_LOAD_SPACE */ -#define FIRMWARE_VERSION 0x000 -#define FIRMWARE_OPCODE 0x004 -#define OPCODE_MASK 0x00000fff -#define OPCODE_GET_IMAGE_DESC 0x00000000 -#define OPCODE_DELETE_IMAGE 0x00000001 -#define OPCODE_CREATE_IMAGE 0x00000002 -#define OPCODE_UPLOAD 0x00000003 -#define OPCODE_UPLOAD_STAT 0x00000004 -#define OPCODE_RESET_IMAGE 0x00000005 -#define OPCODE_TEST_ACTION 0x00000006 -#define OPCODE_GET_RUNNING_IMAGE_VINFO 0x0000000a -#define OPCODE_EXECUTE 0x80000000 -#define FIRMWARE_RETURN_STATUS 0x008 -#define FIRMWARE_PROGRESS 0x00c -#define PROGRESS_CURR_MASK 0x00000fff -#define PROGRESS_MAX_MASK 0x00fff000 -#define PROGRESS_TOUT_MASK 0x0f000000 -#define PROGRESS_FLAG 0x80000000 -#define FIRMWARE_CAPABILITIES 0x010 -#define FL_CAP_AUTOERASE 0x00000001 -#define FL_CAP_PROGRESS 0x00000002 -#define FIRMWARE_DATA 0x02c -#define TEST_CMD_POKE 0x00000001 -#define TEST_CMD_PEEK 0x00000002 -#define CMD_GET_AVS_CNT 0x00000003 -#define CMD_CLR_AVS_CNT 0x00000004 -#define CMD_SET_MODE 0x00000005 -#define CMD_SET_MIDIBP 0x00000006 -#define CMD_GET_AVSPHASE 0x00000007 -#define CMD_ENABLE_BNC_SYNC 0x00000008 -#define CMD_PULSE_BNC_SYNC 0x00000009 -#define CMD_EMUL_SLOW_CMD 0x0000000a -#define FIRMWARE_TEST_DELAY 0xfd8 -#define FIRMWARE_TEST_BUF 0xfdc - - -/* EAP */ -#define EAP_PRIVATE_SPACE 0xffffe0200000uLL - -#define EAP_CAPABILITY_OFFSET 0x000 -#define EAP_CAPABILITY_SIZE 0x004 -/* ... */ - -#define EAP_ROUTER_CAPS 0x000 -#define ROUTER_EXPOSED 0x00000001 -#define ROUTER_READ_ONLY 0x00000002 -#define ROUTER_FLASH 0x00000004 -#define MAX_ROUTES_MASK 0xffff0000 -#define EAP_MIXER_CAPS 0x004 -#define MIXER_EXPOSED 0x00000001 -#define MIXER_READ_ONLY 0x00000002 -#define MIXER_FLASH 0x00000004 -#define MIXER_IN_DEV_MASK 0x000000f0 -#define MIXER_OUT_DEV_MASK 0x00000f00 -#define MIXER_INPUTS_MASK 0x00ff0000 -#define MIXER_OUTPUTS_MASK 0xff000000 -#define EAP_GENERAL_CAPS 0x008 -#define GENERAL_STREAM_CONFIG 0x00000001 -#define GENERAL_FLASH 0x00000002 -#define GENERAL_PEAK 0x00000004 -#define GENERAL_MAX_TX_STREAMS_MASK 0x000000f0 -#define GENERAL_MAX_RX_STREAMS_MASK 0x00000f00 -#define GENERAL_STREAM_CONFIG_FLASH 0x00001000 -#define GENERAL_CHIP_MASK 0x00ff0000 -#define GENERAL_CHIP_DICE_II 0x00000000 -#define GENERAL_CHIP_DICE_MINI 0x00010000 -#define GENERAL_CHIP_DICE_JR 0x00020000 +#include "dice-interface.h"
struct dice { @@ -479,7 +274,7 @@ static int dice_enable_set(struct dice *dice) __be32 value; int rcode, err, errors = 0;
- value = cpu_to_be32(ENABLE); + value = cpu_to_be32(1); for (;;) { rcode = fw_run_transaction(device->card, TCODE_WRITE_QUADLET_REQUEST,