The ZL38060 is a "Connected Home Audio Processor" from Microsemi, which consists of a Digital Signal Processor (DSP), several Digital Audio Interfaces (DAIs), analog outputs, and a block of 14 GPIOs.
This driver supports only a tiny subset of the chip's functionality and possible configurations: - bypass mode (whole dsp block is bypassed) - chip's I2S DAI routed directly to/from DACs and microphone - chip's internal clock is driven by a 12 MHz external crystal - chip's DAI connected to CPU is I2S, and bit + frame clock master - chip must be strapped for "host boot": in this mode, firmware will be provided by this driver.
Signed-off-by: Sven Van Asbroeck TheSven73@gmail.com ---
Tree: v5.7-rc1
v1->v2:
Mark Brown:
- fixup comment style at top of file.
- fixup curly braces in if-elseif-else statement.
- explicitly put the chip in reset so it reverts to a known state.
- remove 'mscc,load-firmware' devicetree property, which provided support for switching between chip bootstrap modes (host boot / auto boot from external flash). On reflection, I cannot test correct operation of auto-boot - it involves interaction with the Bootloader Status Register, and I have no access to an auto-boot zl38060. This means the only tested and supported mode will be 'host boot', where the firmware is programmed by the host CPU (ie. Linux).
- remove amplifier enable gpio. if required, it should be part of the machine layer.
Sven Van Asbroeck:
- add dapm widgets: DAC1, DAC2, DMICL. Routed to Playback and Capture, respectively. This is required to drive a microphone amp-enable gpio from the machine layer.
sound/soc/codecs/Kconfig | 11 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/zl38060.c | 638 +++++++++++++++++++++++++++++++++++++ 3 files changed, 651 insertions(+) create mode 100644 sound/soc/codecs/zl38060.c
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index e6a0c5d05fa5..7cb032757d32 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -272,6 +272,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_WM9712 imply SND_SOC_WM9713 imply SND_SOC_WSA881X + imply SND_SOC_ZL38060 help Normally ASoC codec drivers are only built if a machine driver which uses them is also built since they are only usable with a machine @@ -1642,6 +1643,16 @@ config SND_SOC_WSA881X This enables support for Qualcomm WSA8810/WSA8815 Class-D Smart Speaker Amplifier.
+config SND_SOC_ZL38060 + tristate "Microsemi ZL38060 Connected Home Audio Processor" + depends on SPI_MASTER + select GPIOLIB + select REGMAP + help + Support for ZL38060 Connected Home Audio Processor from Microsemi, + which consists of a Digital Signal Processor (DSP), several Digital + Audio Interfaces (DAIs), analog outputs, and a block of 14 GPIOs. + config SND_SOC_ZX_AUD96P22 tristate "ZTE ZX AUD96P22 CODEC" depends on I2C diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 03533157cda6..a603532c7af5 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -288,6 +288,7 @@ snd-soc-wm9712-objs := wm9712.o snd-soc-wm9713-objs := wm9713.o snd-soc-wm-hubs-objs := wm_hubs.o snd-soc-wsa881x-objs := wsa881x.o +snd-soc-zl38060-objs := zl38060.o snd-soc-zx-aud96p22-objs := zx_aud96p22.o # Amp snd-soc-max9877-objs := max9877.o @@ -588,6 +589,7 @@ obj-$(CONFIG_SND_SOC_WM9713) += snd-soc-wm9713.o obj-$(CONFIG_SND_SOC_WM_ADSP) += snd-soc-wm-adsp.o obj-$(CONFIG_SND_SOC_WM_HUBS) += snd-soc-wm-hubs.o obj-$(CONFIG_SND_SOC_WSA881X) += snd-soc-wsa881x.o +obj-$(CONFIG_SND_SOC_ZL38060) += snd-soc-zl38060.o obj-$(CONFIG_SND_SOC_ZX_AUD96P22) += snd-soc-zx-aud96p22.o
# Amp diff --git a/sound/soc/codecs/zl38060.c b/sound/soc/codecs/zl38060.c new file mode 100644 index 000000000000..927ad849ad2d --- /dev/null +++ b/sound/soc/codecs/zl38060.c @@ -0,0 +1,638 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// Codec driver for Microsemi ZL38060 Connected Home Audio Processor. +// +// Copyright(c) 2020 Sven Van Asbroeck + +// The ZL38060 is very flexible and configurable. This driver implements only a +// tiny subset of the chip's possible configurations: +// +// - DSP block bypassed: DAI routed straight to DACs +// microphone routed straight to DAI +// - chip's internal clock is driven by a 12 MHz external crystal +// - chip's DAI connected to CPU is I2S, and bit + frame clock master +// - chip must be strapped for "host boot": in this mode, firmware will be +// provided by this driver. + +#include <linux/gpio/consumer.h> +#include <linux/gpio/driver.h> +#include <linux/property.h> +#include <linux/spi/spi.h> +#include <linux/regmap.h> +#include <linux/module.h> +#include <linux/ihex.h> + +#include <sound/pcm_params.h> +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/soc.h> + +#define DRV_NAME "zl38060" + +#define ZL38_RATES (SNDRV_PCM_RATE_8000 |\ + SNDRV_PCM_RATE_16000 |\ + SNDRV_PCM_RATE_48000) +#define ZL38_FORMATS SNDRV_PCM_FMTBIT_S16_LE + +#define HBI_FIRMWARE_PAGE 0xFF +#define ZL38_MAX_RAW_XFER 0x100 + +#define REG_TDMA_CFG_CLK 0x0262 +#define CFG_CLK_PCLK_SHIFT 4 +#define CFG_CLK_PCLK_MASK (0x7ff << CFG_CLK_PCLK_SHIFT) +#define CFG_CLK_PCLK(bits) ((bits - 1) << CFG_CLK_PCLK_SHIFT) +#define CFG_CLK_MASTER BIT(15) +#define CFG_CLK_FSRATE_MASK 0x7 +#define CFG_CLK_FSRATE_8KHZ 0x1 +#define CFG_CLK_FSRATE_16KHZ 0x2 +#define CFG_CLK_FSRATE_48KHZ 0x6 + +#define REG_CLK_CFG 0x0016 +#define CLK_CFG_SOURCE_XTAL BIT(15) + +#define REG_CLK_STATUS 0x0014 +#define CLK_STATUS_HWRST BIT(0) + +#define REG_PARAM_RESULT 0x0034 +#define PARAM_RESULT_READY 0xD3D3 + +#define REG_PG255_BASE_HI 0x000C +#define REG_PG255_OFFS(addr) ((HBI_FIRMWARE_PAGE << 8) | (addr & 0xFF)) +#define REG_FWR_EXEC 0x012C + +#define REG_CMD 0x0032 +#define REG_HW_REV 0x0020 +#define REG_FW_PROD 0x0022 +#define REG_FW_REV 0x0024 + +#define REG_SEMA_FLAGS 0x0006 +#define SEMA_FLAGS_BOOT_CMD BIT(0) +#define SEMA_FLAGS_APP_REBOOT BIT(1) + +#define REG_HW_REV 0x0020 +#define REG_FW_PROD 0x0022 +#define REG_FW_REV 0x0024 +#define REG_GPIO_DIR 0x02DC +#define REG_GPIO_DAT 0x02DA + +#define BOOTCMD_LOAD_COMPLETE 0x000D +#define BOOTCMD_FW_GO 0x0008 + +#define FIRMWARE_MAJOR 2 +#define FIRMWARE_MINOR 2 + +struct zl38_codec_priv { + struct device *dev; + struct regmap *regmap; + bool is_stream_in_use[2]; + struct gpio_chip *gpio_chip; +}; + +static int zl38_fw_issue_command(struct regmap *regmap, u16 cmd) +{ + unsigned int val; + int err; + + err = regmap_read_poll_timeout(regmap, REG_SEMA_FLAGS, val, + !(val & SEMA_FLAGS_BOOT_CMD), 10000, + 10000 * 100); + if (err) + return err; + err = regmap_write(regmap, REG_CMD, cmd); + if (err) + return err; + err = regmap_update_bits(regmap, REG_SEMA_FLAGS, SEMA_FLAGS_BOOT_CMD, + SEMA_FLAGS_BOOT_CMD); + if (err) + return err; + + return regmap_read_poll_timeout(regmap, REG_CMD, val, !val, 10000, + 10000 * 100); +} + +static int zl38_fw_go(struct regmap *regmap) +{ + int err; + + err = zl38_fw_issue_command(regmap, BOOTCMD_LOAD_COMPLETE); + if (err) + return err; + + return zl38_fw_issue_command(regmap, BOOTCMD_FW_GO); +} + +static int zl38_fw_enter_boot_mode(struct regmap *regmap) +{ + unsigned int val; + int err; + + err = regmap_update_bits(regmap, REG_CLK_STATUS, CLK_STATUS_HWRST, + CLK_STATUS_HWRST); + if (err) + return err; + + return regmap_read_poll_timeout(regmap, REG_PARAM_RESULT, val, + val == PARAM_RESULT_READY, 1000, 50000); +} + +static int +zl38_fw_send_data(struct regmap *regmap, u32 addr, const void *data, u16 len) +{ + __be32 addr_base = cpu_to_be32(addr & ~0xFF); + int err; + + err = regmap_raw_write(regmap, REG_PG255_BASE_HI, &addr_base, + sizeof(addr_base)); + if (err) + return err; + return regmap_raw_write(regmap, REG_PG255_OFFS(addr), data, len); +} + +static int zl38_fw_send_xaddr(struct regmap *regmap, const void *data) +{ + /* execution address from ihex: 32-bit little endian. + * device register expects 32-bit big endian. + */ + u32 addr = le32_to_cpup(data); + __be32 baddr = cpu_to_be32(addr); + + return regmap_raw_write(regmap, REG_FWR_EXEC, &baddr, sizeof(baddr)); +} + +static int zl38_load_firmware(struct device *dev, struct regmap *regmap) +{ + const struct ihex_binrec *rec; + const struct firmware *fw; + u32 addr; + u16 len; + int err; + + /* how to get this firmware: + * 1. request and download chip firmware from Microsemi + * (provided by Microsemi in srec format) + * 2. convert downloaded firmware from srec to ihex. Simple tool: + * https://gitlab.com/TheSven73/s3-to-irec + * 3. convert ihex to binary (.fw) using ihex2fw tool which is included + * with the Linux kernel sources + */ + err = request_ihex_firmware(&fw, "zl38060.fw", dev); + if (err) + return err; + err = zl38_fw_enter_boot_mode(regmap); + if (err) + goto out; + rec = (const struct ihex_binrec *)fw->data; + while (rec) { + addr = be32_to_cpu(rec->addr); + len = be16_to_cpu(rec->len); + if (addr) { + /* regular data ihex record */ + err = zl38_fw_send_data(regmap, addr, rec->data, len); + } else if (len == 4) { + /* execution address ihex record */ + err = zl38_fw_send_xaddr(regmap, rec->data); + } else { + err = -EINVAL; + } + if (err) + goto out; + /* next ! */ + rec = ihex_next_binrec(rec); + } + err = zl38_fw_go(regmap); + +out: + release_firmware(fw); + return err; +} + + +static int zl38_software_reset(struct regmap *regmap) +{ + unsigned int val; + int err; + + err = regmap_update_bits(regmap, REG_SEMA_FLAGS, SEMA_FLAGS_APP_REBOOT, + SEMA_FLAGS_APP_REBOOT); + if (err) + return err; + + /* wait for host bus interface to settle. + * Not sure if this is required: Microsemi's vendor driver does this, + * but the firmware manual does not mention it. Leave it in, there's + * little downside, apart from a slower reset. + */ + msleep(50); + + return regmap_read_poll_timeout(regmap, REG_SEMA_FLAGS, val, + !(val & SEMA_FLAGS_APP_REBOOT), 10000, + 10000 * 100); +} + +static int zl38_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) +{ + struct zl38_codec_priv *priv = snd_soc_dai_get_drvdata(dai); + int err; + + switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { + case SND_SOC_DAIFMT_I2S: + /* firmware default is normal i2s */ + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_INV_MASK) { + case SND_SOC_DAIFMT_NB_NF: + /* firmware default is normal bitclock and frame */ + break; + default: + return -EINVAL; + } + + switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { + case SND_SOC_DAIFMT_CBM_CFM: + /* always 32 bits per frame (= 16 bits/channel, 2 channels) */ + err = regmap_update_bits(priv->regmap, REG_TDMA_CFG_CLK, + CFG_CLK_MASTER | CFG_CLK_PCLK_MASK, + CFG_CLK_MASTER | CFG_CLK_PCLK(32)); + if (err) + return err; + break; + default: + return -EINVAL; + } + + return 0; +} + +static int zl38_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct zl38_codec_priv *priv = snd_soc_dai_get_drvdata(dai); + bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; + unsigned int fsrate; + int err; + + /* We cannot change hw_params while the dai is already in use - the + * software reset will corrupt the audio. However, this is not required, + * as the chip's TDM buses are fully symmetric, which mandates identical + * rates, channels, and samplebits for record and playback. + */ + if (priv->is_stream_in_use[!tx]) + goto skip_setup; + + switch (params_rate(params)) { + case 8000: + fsrate = CFG_CLK_FSRATE_8KHZ; + break; + case 16000: + fsrate = CFG_CLK_FSRATE_16KHZ; + break; + case 48000: + fsrate = CFG_CLK_FSRATE_48KHZ; + break; + default: + return -EINVAL; + }; + + err = regmap_update_bits(priv->regmap, REG_TDMA_CFG_CLK, + CFG_CLK_FSRATE_MASK, fsrate); + if (err) + return err; + + /* chip requires a software reset to apply audio register changes */ + err = zl38_software_reset(priv->regmap); + if (err) + return err; + +skip_setup: + priv->is_stream_in_use[tx] = true; + + return 0; +} + +static int zl38_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct zl38_codec_priv *priv = snd_soc_dai_get_drvdata(dai); + bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; + + priv->is_stream_in_use[tx] = false; + + return 0; +} + +/* stereo bypass with no AEC */ +static const struct reg_sequence cp_config_stereo_bypass[] = { + /* interconnects must be programmed first */ + { 0x0210, 0x0005 }, /* DAC1 in <= I2S1-L */ + { 0x0212, 0x0006 }, /* DAC2 in <= I2S1-R */ + { 0x0214, 0x0001 }, /* I2S1-L in <= MIC1 */ + { 0x0216, 0x0001 }, /* I2S1-R in <= MIC1 */ + { 0x0224, 0x0000 }, /* AEC-S in <= n/a */ + { 0x0226, 0x0000 }, /* AEC-R in <= n/a */ + /* output enables must be programmed next */ + { 0x0202, 0x000F }, /* enable I2S1 + DAC */ +}; + +static const struct snd_soc_dai_ops zl38_dai_ops = { + .set_fmt = zl38_set_fmt, + .hw_params = zl38_hw_params, + .hw_free = zl38_hw_free, +}; + +static struct snd_soc_dai_driver zl38_dai = { + .name = "zl38060-tdma", + .playback = { + .stream_name = "Playback", + .channels_min = 2, + .channels_max = 2, + .rates = ZL38_RATES, + .formats = ZL38_FORMATS, + }, + .capture = { + .stream_name = "Capture", + .channels_min = 2, + .channels_max = 2, + .rates = ZL38_RATES, + .formats = ZL38_FORMATS, + }, + .ops = &zl38_dai_ops, + .symmetric_rates = 1, + .symmetric_samplebits = 1, + .symmetric_channels = 1, +}; + +static const struct snd_soc_dapm_widget zl38_dapm_widgets[] = { + SND_SOC_DAPM_OUTPUT("DAC1"), + SND_SOC_DAPM_OUTPUT("DAC2"), + + SND_SOC_DAPM_INPUT("DMICL"), +}; + +static const struct snd_soc_dapm_route zl38_dapm_routes[] = { + { "DAC1", NULL, "Playback" }, + { "DAC2", NULL, "Playback" }, + + { "Capture", NULL, "DMICL" }, +}; + +static const struct snd_soc_component_driver zl38_component_dev = { + .dapm_widgets = zl38_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(zl38_dapm_widgets), + .dapm_routes = zl38_dapm_routes, + .num_dapm_routes = ARRAY_SIZE(zl38_dapm_routes), + .endianness = 1, + .non_legacy_dai_naming = 1, +}; + +static void chip_gpio_set(struct gpio_chip *c, unsigned int offset, int val) +{ + struct regmap *regmap = gpiochip_get_data(c); + unsigned int mask = BIT(offset); + + regmap_update_bits(regmap, REG_GPIO_DAT, mask, val ? mask : 0); +} + +static int chip_gpio_get(struct gpio_chip *c, unsigned int offset) +{ + struct regmap *regmap = gpiochip_get_data(c); + unsigned int mask = BIT(offset); + unsigned int val; + int err; + + err = regmap_read(regmap, REG_GPIO_DAT, &val); + if (err) + return err; + + return !!(val & mask); +} + +static int chip_direction_input(struct gpio_chip *c, unsigned int offset) +{ + struct regmap *regmap = gpiochip_get_data(c); + unsigned int mask = BIT(offset); + + return regmap_update_bits(regmap, REG_GPIO_DIR, mask, 0); +} + +static int +chip_direction_output(struct gpio_chip *c, unsigned int offset, int val) +{ + struct regmap *regmap = gpiochip_get_data(c); + unsigned int mask = BIT(offset); + + chip_gpio_set(c, offset, val); + return regmap_update_bits(regmap, REG_GPIO_DIR, mask, mask); +} + +static const struct gpio_chip template_chip = { + .owner = THIS_MODULE, + .label = DRV_NAME, + + .base = -1, + .ngpio = 14, + .direction_input = chip_direction_input, + .direction_output = chip_direction_output, + .get = chip_gpio_get, + .set = chip_gpio_set, + + .can_sleep = true, +}; + +static int zl38_check_revision(struct device *dev, struct regmap *regmap) +{ + unsigned int hwrev, fwprod, fwrev; + int fw_major, fw_minor, fw_micro; + int err; + + err = regmap_read(regmap, REG_HW_REV, &hwrev); + if (err) + return err; + err = regmap_read(regmap, REG_FW_PROD, &fwprod); + if (err) + return err; + err = regmap_read(regmap, REG_FW_REV, &fwrev); + if (err) + return err; + + fw_major = (fwrev >> 12) & 0xF; + fw_minor = (fwrev >> 8) & 0xF; + fw_micro = fwrev & 0xFF; + dev_info(dev, "hw rev 0x%x, fw product code %d, firmware rev %d.%d.%d", + hwrev & 0x1F, fwprod, fw_major, fw_minor, fw_micro); + + if (fw_major != FIRMWARE_MAJOR || fw_minor < FIRMWARE_MINOR) { + dev_err(dev, "unsupported firmware. driver supports %d.%d", + FIRMWARE_MAJOR, FIRMWARE_MINOR); + return -EINVAL; + } + + return 0; +} + +static int zl38_bus_read(void *context, + const void *reg_buf, size_t reg_size, + void *val_buf, size_t val_size) +{ + struct spi_device *spi = context; + const u8 *reg_buf8 = reg_buf; + size_t len = 0; + u8 offs, page; + u8 txbuf[4]; + + if (reg_size != 2 || val_size > ZL38_MAX_RAW_XFER) + return -EINVAL; + + offs = reg_buf8[1] >> 1; + page = reg_buf8[0]; + + if (page) { + txbuf[len++] = 0xFE; + txbuf[len++] = page == HBI_FIRMWARE_PAGE ? 0xFF : page - 1; + txbuf[len++] = offs; + txbuf[len++] = val_size / 2 - 1; + } else { + txbuf[len++] = offs | 0x80; + txbuf[len++] = val_size / 2 - 1; + } + + return spi_write_then_read(spi, txbuf, len, val_buf, val_size); +} + +static int zl38_bus_write(void *context, const void *data, size_t count) +{ + struct spi_device *spi = context; + u8 buf[4 + ZL38_MAX_RAW_XFER]; + size_t val_len, len = 0; + const u8 *data8 = data; + u8 offs, page; + + if (count > (2 + ZL38_MAX_RAW_XFER) || count < 4) + return -EINVAL; + val_len = count - 2; + offs = data8[1] >> 1; + page = data8[0]; + + if (page) { + buf[len++] = 0xFE; + buf[len++] = page == HBI_FIRMWARE_PAGE ? 0xFF : page - 1; + buf[len++] = offs; + buf[len++] = (val_len / 2 - 1) | 0x80; + } else { + buf[len++] = offs | 0x80; + buf[len++] = (val_len / 2 - 1) | 0x80; + } + memcpy(buf + len, data8 + 2, val_len); + len += val_len; + + return spi_write(spi, buf, len); +} + +static const struct regmap_bus zl38_regmap_bus = { + .read = zl38_bus_read, + .write = zl38_bus_write, + .max_raw_write = ZL38_MAX_RAW_XFER, + .max_raw_read = ZL38_MAX_RAW_XFER, +}; + +static const struct regmap_config zl38_regmap_conf = { + .reg_bits = 16, + .val_bits = 16, + .reg_stride = 2, + .use_single_read = true, + .use_single_write = true, +}; + +static int zl38_spi_probe(struct spi_device *spi) +{ + struct device *dev = &spi->dev; + struct zl38_codec_priv *priv; + struct gpio_desc *reset_gpio; + int err; + + /* get the chip to a known state by putting it in reset */ + reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(reset_gpio)) + return PTR_ERR(reset_gpio); + if (reset_gpio) { + /* datasheet: need > 10us for a digital + analog reset */ + usleep_range(15, 50); + /* take the chip out of reset */ + gpiod_set_value_cansleep(reset_gpio, 0); + /* datasheet: need > 3ms for digital section to become stable */ + usleep_range(3000, 10000); + } + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = dev; + dev_set_drvdata(dev, priv); + priv->regmap = devm_regmap_init(dev, &zl38_regmap_bus, spi, + &zl38_regmap_conf); + if (IS_ERR(priv->regmap)) + return PTR_ERR(priv->regmap); + + err = zl38_load_firmware(dev, priv->regmap); + if (err) + return err; + + err = zl38_check_revision(dev, priv->regmap); + if (err) + return err; + + priv->gpio_chip = devm_kmemdup(dev, &template_chip, + sizeof(template_chip), GFP_KERNEL); + if (!priv->gpio_chip) + return -ENOMEM; +#ifdef CONFIG_OF_GPIO + priv->gpio_chip->of_node = dev->of_node; +#endif + err = devm_gpiochip_add_data(dev, priv->gpio_chip, priv->regmap); + if (err) + return err; + + /* setup the cross-point switch for stereo bypass */ + err = regmap_multi_reg_write(priv->regmap, cp_config_stereo_bypass, + ARRAY_SIZE(cp_config_stereo_bypass)); + if (err) + return err; + /* setup for 12MHz crystal connected to the chip */ + err = regmap_update_bits(priv->regmap, REG_CLK_CFG, CLK_CFG_SOURCE_XTAL, + CLK_CFG_SOURCE_XTAL); + if (err) + return err; + + return devm_snd_soc_register_component(dev, &zl38_component_dev, + &zl38_dai, 1); +} + +static const struct of_device_id zl38_dt_ids[] = { + { .compatible = "mscc,zl38060", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, zl38_dt_ids); + +static const struct spi_device_id zl38_spi_ids[] = { + { "zl38060", 0 }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(spi, zl38_spi_ids); + +static struct spi_driver zl38060_spi_driver = { + .driver = { + .name = DRV_NAME, + .of_match_table = of_match_ptr(zl38_dt_ids), + }, + .probe = zl38_spi_probe, + .id_table = zl38_spi_ids, +}; +module_spi_driver(zl38060_spi_driver); + +MODULE_DESCRIPTION("ASoC ZL38060 driver"); +MODULE_AUTHOR("Sven Van Asbroeck TheSven73@gmail.com"); +MODULE_LICENSE("GPL v2");