Apart from pure matching, the bindings also support setting the the reset gpio line.
Signed-off-by: Daniel Mack zonque@gmail.com --- .../devicetree/bindings/sound/adi,adau1701.txt | 23 ++++++++++++++++ sound/soc/codecs/adau1701.c | 31 ++++++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/adi,adau1701.txt
diff --git a/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/Documentation/devicetree/bindings/sound/adi,adau1701.txt new file mode 100644 index 0000000..3afeda7 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1701.txt @@ -0,0 +1,23 @@ +Analog Devices ADAU1701 + +Required properties: + + - compatible: Should contain "adi,adau1701" + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Optional properties: + + - reset-gpio: A GPIO spec to define which pin is connected to the + chip's !RESET pin. If specified, the driver will + assert a hardware reset at probe time. + +Examples: + + i2c_bus { + adau1701@34 { + compatible = "adi,adau1701"; + reg = <0x34>; + reset-gpio = <&gpio 23 0>; + }; + }; diff --git a/sound/soc/codecs/adau1701.c b/sound/soc/codecs/adau1701.c index 95e1677..6515ba7 100644 --- a/sound/soc/codecs/adau1701.c +++ b/sound/soc/codecs/adau1701.c @@ -13,6 +13,9 @@ #include <linux/i2c.h> #include <linux/delay.h> #include <linux/slab.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_device.h> #include <sound/core.h> #include <sound/pcm.h> #include <sound/pcm_params.h> @@ -452,13 +455,40 @@ static struct snd_soc_dai_driver adau1701_dai = { .symmetric_rates = 1, };
+#ifdef CONFIG_OF +static const struct of_device_id adau1701_dt_ids[] = { + { .compatible = "adi,adau1701", }, + { } +}; +MODULE_DEVICE_TABLE(of, adau1701_dt_ids); +#endif + static int adau1701_probe(struct snd_soc_codec *codec) { int ret; + struct device *dev = codec->dev; struct i2c_client *client = to_i2c_client(codec->dev); + int gpio_nreset = -EINVAL;
codec->control_data = client;
+ if (of_match_device(of_match_ptr(adau1701_dt_ids), dev)) + gpio_nreset = of_get_named_gpio(dev->of_node, + "reset-gpio", 0); + + if (gpio_is_valid(gpio_nreset)) { + if (devm_gpio_request_one(codec->dev, gpio_nreset, + GPIOF_OUT_INIT_LOW, + "ADAU1701 Reset") < 0) + return -EINVAL; + + /* minimum reset time is 20ns */ + udelay(1); + gpio_set_value(gpio_nreset, 1); + /* power-up time may be as long as 85ms */ + mdelay(85); + } + ret = adau1701_load_firmware(client); if (ret) dev_warn(codec->dev, "Failed to load firmware\n"); @@ -522,6 +552,7 @@ static struct i2c_driver adau1701_i2c_driver = { .driver = { .name = "adau1701", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(adau1701_dt_ids), }, .probe = adau1701_i2c_probe, .remove = adau1701_i2c_remove,