Some boards have this pin tied to board and do not require any configuration, some other boards allow to enable chip using GPIO.
Add an option that tells which GPIO is used to power up the codec.
Signed-off-by: Anatol Pomozov anatol.pomozov@gmail.com --- Documentation/devicetree/bindings/sound/rt5677.txt | 41 +++++++++++++++++++++ sound/soc/codecs/rt5677.c | 42 ++++++++++++++++++++++ sound/soc/codecs/rt5677.h | 1 + 3 files changed, 84 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/rt5677.txt
diff --git a/Documentation/devicetree/bindings/sound/rt5677.txt b/Documentation/devicetree/bindings/sound/rt5677.txt new file mode 100644 index 0000000..98509fb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5677.txt @@ -0,0 +1,41 @@ +RT5677 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5677". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin. + +Pins on the device (for linking into audio routes): + + * IN1P + * IN1N + * IN2P + * IN2N + * MICBIAS1 + * DMIC1 + * DMIC2 + * DMIC3 + * DMIC4 + * LOUT1 + * LOUT2 + * LOUT3 + +Example: + +rt5677 { + compatible = "realtek,rt5677"; + reg = <0x2c>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,pow-ldo2-gpio = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c index 9847473..fbaceb6 100644 --- a/sound/soc/codecs/rt5677.c +++ b/sound/soc/codecs/rt5677.c @@ -15,6 +15,7 @@ #include <linux/init.h> #include <linux/delay.h> #include <linux/pm.h> +#include <linux/of_gpio.h> #include <linux/regmap.h> #include <linux/i2c.h> #include <linux/platform_device.h> @@ -3495,6 +3496,24 @@ static const struct i2c_device_id rt5677_i2c_id[] = { }; MODULE_DEVICE_TABLE(i2c, rt5677_i2c_id);
+static int rt5677_parse_dt(struct rt5677_priv *rt5677, struct device_node *np) +{ + rt5677->pow_ldo2 = of_get_named_gpio(np, + "realtek,pow-ldo2-gpio", 0); + + /* + * POW_LDO2 is optional (it may be statically tied on the board). + * -ENOENT means that the property doesn't exist, i.e. there is no + * GPIO, so is not an error. Any other error code means the property + * exists, but could not be parsed. + */ + if (!gpio_is_valid(rt5677->pow_ldo2) && + (rt5677->pow_ldo2 != -ENOENT)) + return rt5677->pow_ldo2; + + return 0; +} + static int rt5677_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { @@ -3513,6 +3532,29 @@ static int rt5677_i2c_probe(struct i2c_client *i2c, if (pdata) rt5677->pdata = *pdata;
+ if (i2c->dev.of_node) { + ret = rt5677_parse_dt(rt5677, i2c->dev.of_node); + if (ret) { + dev_err(&i2c->dev, "Failed to parse device tree: %d\n", + ret); + return ret; + } + } else { + rt5677->pow_ldo2 = -EINVAL; + } + + if (gpio_is_valid(rt5677->pow_ldo2)) { + ret = devm_gpio_request_one(&i2c->dev, rt5677->pow_ldo2, + GPIOF_OUT_INIT_HIGH, + "RT5677 POW_LDO2"); + if (ret < 0) { + dev_err(&i2c->dev, "Failed to request POW_LDO2 %d: %d\n", + rt5677->pow_ldo2, ret); + return ret; + } + msleep(10); + } + rt5677->regmap = devm_regmap_init_i2c(i2c, &rt5677_regmap); if (IS_ERR(rt5677->regmap)) { ret = PTR_ERR(rt5677->regmap); diff --git a/sound/soc/codecs/rt5677.h b/sound/soc/codecs/rt5677.h index b61b72c..222a4137 100644 --- a/sound/soc/codecs/rt5677.h +++ b/sound/soc/codecs/rt5677.h @@ -1550,6 +1550,7 @@ struct rt5677_priv { int pll_src; int pll_in; int pll_out; + int pow_ldo2; /* POW_LDO2 pin */ #ifdef CONFIG_GPIOLIB struct gpio_chip gpio_chip; #endif