Add more fields and improve API when EC presents data through ACPI memory space.
Acked-by: Enric Balletbo i Serra enric.balletbo@collabora.com Acked-by: Benson Leung bleung@chromium.org Reviewed-by: Fabien Lahoudere fabien.lahoudere@collabora.com Signed-off-by: Gwendal Grignou gwendal@chromium.org --- include/linux/mfd/cros_ec_commands.h | 419 +++++++++++++++++++-------- 1 file changed, 293 insertions(+), 126 deletions(-)
diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h index e97e9e976bd0..575066b90bab 100644 --- a/include/linux/mfd/cros_ec_commands.h +++ b/include/linux/mfd/cros_ec_commands.h @@ -83,13 +83,15 @@ /* Unused 0x28 - 0x2f */ #define EC_MEMMAP_SWITCHES 0x30 /* 8 bits */ /* Unused 0x31 - 0x33 */ -#define EC_MEMMAP_HOST_EVENTS 0x34 /* 32 bits */ -/* Reserve 0x38 - 0x3f for additional host event-related stuff */ -/* Battery values are all 32 bits */ +#define EC_MEMMAP_HOST_EVENTS 0x34 /* 64 bits */ +/* Battery values are all 32 bits, unless otherwise noted. */ #define EC_MEMMAP_BATT_VOLT 0x40 /* Battery Present Voltage */ #define EC_MEMMAP_BATT_RATE 0x44 /* Battery Present Rate */ #define EC_MEMMAP_BATT_CAP 0x48 /* Battery Remaining Capacity */ -#define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, defined below */ +#define EC_MEMMAP_BATT_FLAG 0x4c /* Battery State, see below (8-bit) */ +#define EC_MEMMAP_BATT_COUNT 0x4d /* Battery Count (8-bit) */ +#define EC_MEMMAP_BATT_INDEX 0x4e /* Current Battery Data Index (8-bit) */ +/* Unused 0x4f */ #define EC_MEMMAP_BATT_DCAP 0x50 /* Battery Design Capacity */ #define EC_MEMMAP_BATT_DVLT 0x54 /* Battery Design Voltage */ #define EC_MEMMAP_BATT_LFCC 0x58 /* Battery Last Full Charge Capacity */ @@ -103,10 +105,19 @@ /* Unused 0x84 - 0x8f */ #define EC_MEMMAP_ACC_STATUS 0x90 /* Accelerometer status (8 bits )*/ /* Unused 0x91 */ -#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometer data 0x92 - 0x9f */ +#define EC_MEMMAP_ACC_DATA 0x92 /* Accelerometers data 0x92 - 0x9f */ +/* 0x92: Lid Angle if available, LID_ANGLE_UNRELIABLE otherwise */ +/* 0x94 - 0x99: 1st Accelerometer */ +/* 0x9a - 0x9f: 2nd Accelerometer */ #define EC_MEMMAP_GYRO_DATA 0xa0 /* Gyroscope data 0xa0 - 0xa5 */ -/* Unused 0xa6 - 0xfe (remember, 0xff is NOT part of the memmap region) */ +/* Unused 0xa6 - 0xdf */
+/* + * ACPI is unable to access memory mapped data at or above this offset due to + * limitations of the ACPI protocol. Do not place data in the range 0xe0 - 0xfe + * which might be needed by ACPI. + */ +#define EC_MEMMAP_NO_ACPI 0xe0
/* Define the format of the accelerometer mapped memory status byte. */ #define EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK 0x0f @@ -155,6 +166,8 @@ #define EC_BATT_FLAG_DISCHARGING 0x04 #define EC_BATT_FLAG_CHARGING 0x08 #define EC_BATT_FLAG_LEVEL_CRITICAL 0x10 +/* Set if some of the static/dynamic data is invalid (or outdated). */ +#define EC_BATT_FLAG_INVALID_DATA 0x20
/* Switch flags at EC_MEMMAP_SWITCHES */ #define EC_SWITCH_LID_OPEN 0x01 @@ -180,12 +193,200 @@ #define EC_WIRELESS_SWITCH_WWAN 0x04 /* WWAN power */ #define EC_WIRELESS_SWITCH_WLAN_POWER 0x08 /* WLAN power */
+/*****************************************************************************/ +/* + * ACPI commands + * + * These are valid ONLY on the ACPI command/data port. + */ + +/* + * ACPI Read Embedded Controller + * + * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*). + * + * Use the following sequence: + * + * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD + * - Wait for EC_LPC_CMDR_PENDING bit to clear + * - Write address to EC_LPC_ADDR_ACPI_DATA + * - Wait for EC_LPC_CMDR_DATA bit to set + * - Read value from EC_LPC_ADDR_ACPI_DATA + */ +#define EC_CMD_ACPI_READ 0x0080 + +/* + * ACPI Write Embedded Controller + * + * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*). + * + * Use the following sequence: + * + * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD + * - Wait for EC_LPC_CMDR_PENDING bit to clear + * - Write address to EC_LPC_ADDR_ACPI_DATA + * - Wait for EC_LPC_CMDR_PENDING bit to clear + * - Write value to EC_LPC_ADDR_ACPI_DATA + */ +#define EC_CMD_ACPI_WRITE 0x0081 + +/* + * ACPI Burst Enable Embedded Controller + * + * This enables burst mode on the EC to allow the host to issue several + * commands back-to-back. While in this mode, writes to mapped multi-byte + * data are locked out to ensure data consistency. + */ +#define EC_CMD_ACPI_BURST_ENABLE 0x0082 + +/* + * ACPI Burst Disable Embedded Controller + * + * This disables burst mode on the EC and stops preventing EC writes to mapped + * multi-byte data. + */ +#define EC_CMD_ACPI_BURST_DISABLE 0x0083 + +/* + * ACPI Query Embedded Controller + * + * This clears the lowest-order bit in the currently pending host events, and + * sets the result code to the 1-based index of the bit (event 0x00000001 = 1, + * event 0x80000000 = 32), or 0 if no event was pending. + */ +#define EC_CMD_ACPI_QUERY_EVENT 0x0084 + +/* Valid addresses in ACPI memory space, for read/write commands */ + +/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */ +#define EC_ACPI_MEM_VERSION 0x00 +/* + * Test location; writing value here updates test compliment byte to (0xff - + * value). + */ +#define EC_ACPI_MEM_TEST 0x01 +/* Test compliment; writes here are ignored. */ +#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02 + +/* Keyboard backlight brightness percent (0 - 100) */ +#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03 +/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */ +#define EC_ACPI_MEM_FAN_DUTY 0x04 + +/* + * DPTF temp thresholds. Any of the EC's temp sensors can have up to two + * independent thresholds attached to them. The current value of the ID + * register determines which sensor is affected by the THRESHOLD and COMMIT + * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme + * as the memory-mapped sensors. The COMMIT register applies those settings. + * + * The spec does not mandate any way to read back the threshold settings + * themselves, but when a threshold is crossed the AP needs a way to determine + * which sensor(s) are responsible. Each reading of the ID register clears and + * returns one sensor ID that has crossed one of its threshold (in either + * direction) since the last read. A value of 0xFF means "no new thresholds + * have tripped". Setting or enabling the thresholds for a sensor will clear + * the unread event count for that sensor. + */ +#define EC_ACPI_MEM_TEMP_ID 0x05 +#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06 +#define EC_ACPI_MEM_TEMP_COMMIT 0x07 +/* + * Here are the bits for the COMMIT register: + * bit 0 selects the threshold index for the chosen sensor (0/1) + * bit 1 enables/disables the selected threshold (0 = off, 1 = on) + * Each write to the commit register affects one threshold. + */ +#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK BIT(0) +#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK BIT(1) +/* + * Example: + * + * Set the thresholds for sensor 2 to 50 C and 60 C: + * write 2 to [0x05] -- select temp sensor 2 + * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET + * write 0x2 to [0x07] -- enable threshold 0 with this value + * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET + * write 0x3 to [0x07] -- enable threshold 1 with this value + * + * Disable the 60 C threshold, leaving the 50 C threshold unchanged: + * write 2 to [0x05] -- select temp sensor 2 + * write 0x1 to [0x07] -- disable threshold 1 + */ + +/* DPTF battery charging current limit */ +#define EC_ACPI_MEM_CHARGING_LIMIT 0x08 + +/* Charging limit is specified in 64 mA steps */ +#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64 +/* Value to disable DPTF battery charging limit */ +#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff + +/* + * Report device orientation + * Bits Definition + * 3:1 Device DPTF Profile Number (DDPN) + * 0 = Reserved for backward compatibility (indicates no valid + * profile number. Host should fall back to using TBMD). + * 1..7 = DPTF Profile number to indicate to host which table needs + * to be loaded. + * 0 Tablet Mode Device Indicator (TBMD) + */ +#define EC_ACPI_MEM_DEVICE_ORIENTATION 0x09 +#define EC_ACPI_MEM_TBMD_SHIFT 0 +#define EC_ACPI_MEM_TBMD_MASK 0x1 +#define EC_ACPI_MEM_DDPN_SHIFT 1 +#define EC_ACPI_MEM_DDPN_MASK 0x7 + +/* + * Report device features. Uses the same format as the host command, except: + * + * bit 0 (EC_FEATURE_LIMITED) changes meaning from "EC code has a limited set + * of features", which is of limited interest when the system is already + * interpreting ACPI bytecode, to "EC_FEATURES[0-7] is not supported". Since + * these are supported, it defaults to 0. + * This allows detecting the presence of this field since older versions of + * the EC codebase would simply return 0xff to that unknown address. Check + * FEATURES0 != 0xff (or FEATURES0[0] == 0) to make sure that the other bits + * are valid. + */ +#define EC_ACPI_MEM_DEVICE_FEATURES0 0x0a +#define EC_ACPI_MEM_DEVICE_FEATURES1 0x0b +#define EC_ACPI_MEM_DEVICE_FEATURES2 0x0c +#define EC_ACPI_MEM_DEVICE_FEATURES3 0x0d +#define EC_ACPI_MEM_DEVICE_FEATURES4 0x0e +#define EC_ACPI_MEM_DEVICE_FEATURES5 0x0f +#define EC_ACPI_MEM_DEVICE_FEATURES6 0x10 +#define EC_ACPI_MEM_DEVICE_FEATURES7 0x11 + +#define EC_ACPI_MEM_BATTERY_INDEX 0x12 + +/* + * USB Port Power. Each bit indicates whether the corresponding USB ports' power + * is enabled (1) or disabled (0). + * bit 0 USB port ID 0 + * ... + * bit 7 USB port ID 7 + */ +#define EC_ACPI_MEM_USB_PORT_POWER 0x13 + +/* + * ACPI addresses 0x20 - 0xff map to EC_MEMMAP offset 0x00 - 0xdf. This data + * is read-only from the AP. Added in EC_ACPI_MEM_VERSION 2. + */ +#define EC_ACPI_MEM_MAPPED_BEGIN 0x20 +#define EC_ACPI_MEM_MAPPED_SIZE 0xe0 + +/* Current version of ACPI memory address space */ +#define EC_ACPI_MEM_VERSION_CURRENT 2 + + /* * This header file is used in coreboot both in C and ACPI code. The ACPI code * is pre-processed to handle constants but the ASL compiler is unable to * handle actual C code so keep it separate. */ -#ifndef __ACPI__ +
/* * Attributes for EC request and response packets. Just defining __packed @@ -238,7 +439,7 @@ #define EC_LPC_STATUS_PROCESSING 0x04 /* Last write to EC was a command, not data */ #define EC_LPC_STATUS_LAST_CMD 0x08 -/* EC is in burst mode. Unsupported by Chrome EC, so this bit is never set */ +/* EC is in burst mode */ #define EC_LPC_STATUS_BURST_MODE 0x10 /* SCI event is pending (requesting SCI query) */ #define EC_LPC_STATUS_SCI_PENDING 0x20 @@ -2323,6 +2524,8 @@ struct ec_response_temp_sensor_get_info { /*****************************************************************************/ /* Host event commands */
+ +/* Obsolete. New implementation should use EC_CMD_HOST_EVENT instead */ /* * Host event mask params and response structures, shared by all of the host * event commands below. @@ -2348,6 +2551,86 @@ struct ec_response_host_event_mask { #define EC_CMD_HOST_EVENT_SET_WAKE_MASK 0x008E #define EC_CMD_HOST_EVENT_CLEAR_B 0x008F
+/* + * Unified host event programming interface - Should be used by newer versions + * of BIOS/OS to program host events and masks + */ + +struct ec_params_host_event { + + /* Action requested by host - one of enum ec_host_event_action. */ + uint8_t action; + + /* + * Mask type that the host requested the action on - one of + * enum ec_host_event_mask_type. + */ + uint8_t mask_type; + + /* Set to 0, ignore on read */ + uint16_t reserved; + + /* Value to be used in case of set operations. */ + uint64_t value; +} __ec_align4; + +/* + * Response structure returned by EC_CMD_HOST_EVENT. + * Update the value on a GET request. Set to 0 on GET/CLEAR + */ + +struct ec_response_host_event { + + /* Mask value in case of get operation */ + uint64_t value; +} __ec_align4; + +enum ec_host_event_action { + /* + * params.value is ignored. Value of mask_type populated + * in response.value + */ + EC_HOST_EVENT_GET, + + /* Bits in params.value are set */ + EC_HOST_EVENT_SET, + + /* Bits in params.value are cleared */ + EC_HOST_EVENT_CLEAR, +}; + +enum ec_host_event_mask_type { + + /* Main host event copy */ + EC_HOST_EVENT_MAIN, + + /* Copy B of host events */ + EC_HOST_EVENT_B, + + /* SCI Mask */ + EC_HOST_EVENT_SCI_MASK, + + /* SMI Mask */ + EC_HOST_EVENT_SMI_MASK, + + /* Mask of events that should be always reported in hostevents */ + EC_HOST_EVENT_ALWAYS_REPORT_MASK, + + /* Active wake mask */ + EC_HOST_EVENT_ACTIVE_WAKE_MASK, + + /* Lazy wake mask for S0ix */ + EC_HOST_EVENT_LAZY_WAKE_MASK_S0IX, + + /* Lazy wake mask for S3 */ + EC_HOST_EVENT_LAZY_WAKE_MASK_S3, + + /* Lazy wake mask for S5 */ + EC_HOST_EVENT_LAZY_WAKE_MASK_S5, +}; + +#define EC_CMD_HOST_EVENT 0x00A4 + /*****************************************************************************/ /* Switch commands */
@@ -3056,122 +3339,6 @@ struct ec_params_reboot_ec { */ #define EC_CMD_GET_PANIC_INFO 0x00D3
-/*****************************************************************************/ -/* - * ACPI commands - * - * These are valid ONLY on the ACPI command/data port. - */ - -/* - * ACPI Read Embedded Controller - * - * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*). - * - * Use the following sequence: - * - * - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD - * - Wait for EC_LPC_CMDR_PENDING bit to clear - * - Write address to EC_LPC_ADDR_ACPI_DATA - * - Wait for EC_LPC_CMDR_DATA bit to set - * - Read value from EC_LPC_ADDR_ACPI_DATA - */ -#define EC_CMD_ACPI_READ 0x80 - -/* - * ACPI Write Embedded Controller - * - * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*). - * - * Use the following sequence: - * - * - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD - * - Wait for EC_LPC_CMDR_PENDING bit to clear - * - Write address to EC_LPC_ADDR_ACPI_DATA - * - Wait for EC_LPC_CMDR_PENDING bit to clear - * - Write value to EC_LPC_ADDR_ACPI_DATA - */ -#define EC_CMD_ACPI_WRITE 0x81 - -/* - * ACPI Query Embedded Controller - * - * This clears the lowest-order bit in the currently pending host events, and - * sets the result code to the 1-based index of the bit (event 0x00000001 = 1, - * event 0x80000000 = 32), or 0 if no event was pending. - */ -#define EC_CMD_ACPI_QUERY_EVENT 0x84 - -/* Valid addresses in ACPI memory space, for read/write commands */ - -/* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */ -#define EC_ACPI_MEM_VERSION 0x00 -/* - * Test location; writing value here updates test compliment byte to (0xff - - * value). - */ -#define EC_ACPI_MEM_TEST 0x01 -/* Test compliment; writes here are ignored. */ -#define EC_ACPI_MEM_TEST_COMPLIMENT 0x02 - -/* Keyboard backlight brightness percent (0 - 100) */ -#define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03 -/* DPTF Target Fan Duty (0-100, 0xff for auto/none) */ -#define EC_ACPI_MEM_FAN_DUTY 0x04 - -/* - * DPTF temp thresholds. Any of the EC's temp sensors can have up to two - * independent thresholds attached to them. The current value of the ID - * register determines which sensor is affected by the THRESHOLD and COMMIT - * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme - * as the memory-mapped sensors. The COMMIT register applies those settings. - * - * The spec does not mandate any way to read back the threshold settings - * themselves, but when a threshold is crossed the AP needs a way to determine - * which sensor(s) are responsible. Each reading of the ID register clears and - * returns one sensor ID that has crossed one of its threshold (in either - * direction) since the last read. A value of 0xFF means "no new thresholds - * have tripped". Setting or enabling the thresholds for a sensor will clear - * the unread event count for that sensor. - */ -#define EC_ACPI_MEM_TEMP_ID 0x05 -#define EC_ACPI_MEM_TEMP_THRESHOLD 0x06 -#define EC_ACPI_MEM_TEMP_COMMIT 0x07 -/* - * Here are the bits for the COMMIT register: - * bit 0 selects the threshold index for the chosen sensor (0/1) - * bit 1 enables/disables the selected threshold (0 = off, 1 = on) - * Each write to the commit register affects one threshold. - */ -#define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK (1 << 0) -#define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK (1 << 1) -/* - * Example: - * - * Set the thresholds for sensor 2 to 50 C and 60 C: - * write 2 to [0x05] -- select temp sensor 2 - * write 0x7b to [0x06] -- C_TO_K(50) - EC_TEMP_SENSOR_OFFSET - * write 0x2 to [0x07] -- enable threshold 0 with this value - * write 0x85 to [0x06] -- C_TO_K(60) - EC_TEMP_SENSOR_OFFSET - * write 0x3 to [0x07] -- enable threshold 1 with this value - * - * Disable the 60 C threshold, leaving the 50 C threshold unchanged: - * write 2 to [0x05] -- select temp sensor 2 - * write 0x1 to [0x07] -- disable threshold 1 - */ - -/* DPTF battery charging current limit */ -#define EC_ACPI_MEM_CHARGING_LIMIT 0x08 - -/* Charging limit is specified in 64 mA steps */ -#define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA 64 -/* Value to disable DPTF battery charging limit */ -#define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED 0xff - -/* Current version of ACPI memory address space */ -#define EC_ACPI_MEM_VERSION_CURRENT 1 - - /*****************************************************************************/ /* * HDMI CEC commands @@ -3285,8 +3452,6 @@ enum mkbp_cec_event { */ #define EC_CMD_VERSION0 0x00DC
-#endif /* !__ACPI__ */ - /*****************************************************************************/ /* * PD commands @@ -3627,4 +3792,6 @@ struct ec_response_usb_pd_mux_info { #define EC_LPC_ADDR_OLD_PARAM EC_HOST_CMD_REGION1 #define EC_OLD_PARAM_SIZE EC_HOST_CMD_REGION_SIZE
+ + #endif /* __CROS_EC_COMMANDS_H */