05.11.2013 15:43, Takashi Iwai kirjoitti:
At Fri, 01 Nov 2013 23:43:12 +0200, Anssi Hannula wrote:
Hi all!
Currently we allow the use of CA values up to 0x31 as defined in CEA-861-E/F. However, only CA values up to 0x19 are defined in CEA-861-B/C/D.
HDMI specification 1.4b specifies that the CA field is to be filled according to CEA-861-D, and DisplayPort 1.1a according to CEA-861-C.
The ELD (EDID-Like Data) format as specified by Intel HDA specification 1.0a has a speaker allocation bitmask that only accommodates speakers present in CEA-861-D; all of the 0x20+ CAs contain speakers that do not have a corresponding bit in ELD.
Using a CA value unsupported by sink will cause either a completely silent output or stereo output, so I think we should try to prevent selecting such channel maps, if feasible.
However, before doing anything, I wonder if they are actually supported by some newer receivers (mine is 4 years old). It'd be good if someone with a newish receiver could try the below :) To test this, one can run (replacing XX and YY with appropriate values from "aplay -L") on *sound git master*: speaker-test -c6 -Dhdmi:CARD=XX,DEV=YY -m FL,FR,RL,RR,FLH,FRH If you get some output for the RL/RR speakers, that should mean that 0x20+ CAs are supported. If there is no output except on FL/FR and there is proper output without the "-m FL,FR,RL,RR,FLH,FRH", this means that 0x20+ CAs are not supported.
I think there are about these options for us to take: a) drop 0x20+ CAs from channel_allocations altogether b) put the 0x20+ CAs under a module parameter c) only allow 0x20+ CAs if any CEA-861-E+ only speakers are specified in EDID. However, as ELD doesn't have bits for these, we'd have to employ some non-standard bits in ELD or communicate directly with video driver. d) do nothing, allow the 0x20+ CAs.
IMHO we should do something, since players using ALSA channel mapping could just automatically select a manual channel map that uses an unsupported 0x20+ CA if the source audio stream contains such channels...
WDYT?
Practical options as of now are either (b) or (d).
Extending EDID in a non-standard way is no-go. Better to put finger away. OTOH, if we're going to that direction, we should rather build a better / more direct communication way with the graphics driver, instead. This would make things in Intel graphics easier, too, for example.
Yeah, another benefit of that would be getting the sink manufacturer/product/name etc on the older (i.e. all but the very latest) ATI/AMD cards. Of course that is a rather limited benefit, and I'm not sure this 0x20+ CAs stuff is worth it either...
And (a) isn't the best option, obviously.
Now the question is whether (b) or (d). Can 0x20+ CA be chosen by default from any applications without extra setup? If it can be done only via user's manual configuration or option, it's essentially user's responsibility. If so, adding an option to the module is nothing but one more annoyance. Then I'd take (d).
If 0x20+ can be selected automatically in some situations, it'd make sense to block it as default, so (b) would be the choice. But I guess it won't happen normally.
Well, I guess not many applications have ALSA chmap support yet, so the answer is "not chosen by default" for now.
I'm going to probably be writing ALSA chmap support for XBMC, and I will probably try to set a channel map according to the source audio stream channel map (if possible) to avoid software remapping, though. I don't have the exact behavior planned out yet, though, but unless 0x20+ CAs are blocked by ALSA, I think I'll just avoid using the E+ speaker positions by default for HDMI in XBMC ALSA code.
For the record, the E+ speaker positions are FLH, FRH, FCH, FLW, FRW, TC, so they aren't very common. And since HDMI 1.x supports just 8 PCM channels, using those in discrete PCM mode means dropping some of the standard 7.1 speakers (passthrough is of course a different story).
Also, even though Peter's receiver accepted the CAs, the receiver channel mapping was somewhat weird (e.g. front wide channels were mapped to rear speakers).
I guess I'm leaning towards (d)...