Hi Takashi,
-----Original Message----- From: Takashi Iwai [mailto:tiwai@suse.de] Sent: Monday, May 6, 2019 4:40 PM To: Jaroslav Kysela perex@perex.cz Cc: Yang, Libin libin.yang@intel.com; alsa-devel@alsa-project.org; pierre- louis.bossart@linux.intel.com; broonie@kernel.org; subhransu.s.prusty@intel.com; samreen.nilofer@intel.com Subject: Re: [alsa-devel] [RFC PATCH] ASoC: codec: hdac_hdmi: no checking monitor in hw_params
On Mon, 06 May 2019 10:19:48 +0200, Jaroslav Kysela wrote:
Dne 06. 05. 19 v 8:59 libin.yang@intel.com napsal(a):
From: Libin Yang libin.yang@intel.com
This patch move the check of monitor from hw_params to trigger callback.
The original code will check the monitor presence in hw_params. If the monitor doesn't exist, hw_params will return -ENODEV. Mostly this is
OK.
However, pulseaudio will check the pcm devices when kernel is booting up. It will try to open, set hw_params, prepare such pcm devices. We can't guarantee that the monitor will be connected when kernel is booting
up.
Especially, hdac_hdmi will export 3 pcms at most. It's hard to say users will connect 3 monitors to the HDMI/DP ports. This will cause pulseaudio fail in parsing the pcm devices because the driver will return -ENODEV in hw_params.
This patch tries to move the check of monitor presence into trigger callback. This can "trick" the pulseaudio the pcm is ready.
This bug is found when we try to enable HDMI detection in gnome-sound-setting for ASoC hdac_hdmi. After we enable the hdmi in UCM, pulseaudio will try to parse the hdmi pcm devices. It will cause failure if there are no monitors connected.
I don't like this solution much. PA should use the Jack control to add the devices dynamically and avoid probing when the Jack control is false.
Ideally, yes, but this isn't going to happen soon, I'm afraid. And we're still responsible for fixing for the existing platforms. So I find the proposed patch OK although it's hackish. The added code in the trigger has almost no overhead, and it won't break stuff.
Yes, this is why we want to use UCM. We need more changes in the driver to use Jack control.
I have another question: Is it possible that we remove the monitor detection? I mean just returning ok even there are no monitors?
There is one case: playback -> disconnect monitor -> S3. As it will trigger start after S3, my patch will cause playback to exit as it will check the monitors. The original code will not break playback in this case.
Regards, Libin
thanks,
Takashi
JaroslavSigned-off-by: Libin Yang libin.yang@intel.com
sound/soc/codecs/hdac_hdmi.c | 44 +++++++++++++++++++++++++++++++------------- 1 file changed, 31 insertions(+), 13 deletions(-)
diff --git a/sound/soc/codecs/hdac_hdmi.c b/sound/soc/codecs/hdac_hdmi.c index 4de1fbf..f482e09 100644 --- a/sound/soc/codecs/hdac_hdmi.c +++ b/sound/soc/codecs/hdac_hdmi.c @@ -455,24 +455,11 @@ static int hdac_hdmi_set_hw_params(struct
snd_pcm_substream *substream,
struct snd_pcm_hw_params *hparams, struct snd_soc_dai *dai) { struct hdac_hdmi_priv *hdmi = snd_soc_dai_get_drvdata(dai);
struct hdac_device *hdev = hdmi->hdev; struct hdac_hdmi_dai_port_map *dai_map;
struct hdac_hdmi_port *port; struct hdac_hdmi_pcm *pcm; int format;
dai_map = &hdmi->dai_map[dai->id];
port = dai_map->port;
if (!port)
return -ENODEV;if ((!port->eld.monitor_present) || (!port->eld.eld_valid)) {
dev_err(&hdev->dev,"device is not configured for this pin:port%d:%d\n",port->pin->nid, port->id);return -ENODEV;}
format = snd_hdac_calc_stream_format(params_rate(hparams), params_channels(hparams),
params_format(hparams), @@ -630,6
+617,36 @@ static void hdac_hdmi_pcm_close(struct snd_pcm_substream
*substream,
dai_map->port = NULL;}
+static int hdac_hdmi_pcm_trigger(struct snd_pcm_substream *substream,
int cmd,
struct snd_soc_dai *dai)+{
- struct hdac_hdmi_port *port;
- struct hdac_hdmi_dai_port_map *dai_map;
- struct hdac_hdmi_priv *hdmi = snd_soc_dai_get_drvdata(dai);
- struct hdac_device *hdev = hdmi->hdev;
- /*
* When start, if there is no monitor,* It should not start audio.*/- if (cmd == SNDRV_PCM_TRIGGER_START) {
dai_map = &hdmi->dai_map[dai->id];port = dai_map->port;if (!port)return -ENODEV;if ((!port->eld.monitor_present) || (!port->eld.eld_valid)) {dev_err(&hdev->dev,"device is not configured for thispin:port%d:%d\n",
port->pin->nid, port->id);return -ENODEV;}- }
- return 0;
+}
static int hdac_hdmi_query_cvt_params(struct hdac_device *hdev, struct hdac_hdmi_cvt *cvt) { @@ -1389,6 +1406,7 @@ static const struct snd_soc_dai_ops hdmi_dai_ops = { .startup = hdac_hdmi_pcm_open, .shutdown = hdac_hdmi_pcm_close, .hw_params = hdac_hdmi_set_hw_params,
- .trigger = hdac_hdmi_pcm_trigger, .set_tdm_slot = hdac_hdmi_set_tdm_slot, };
-- Jaroslav Kysela perex@perex.cz Linux Sound Maintainer; ALSA Project; Red Hat, Inc.