Mark Brown wrote:
On Wed, Jul 28, 2010 at 12:04:44PM +0900, Chanwoo Choi wrote:
+static struct regulator_consumer_supply wm8994_fixed_voltage0_supplies[] = {
- {
.dev_name = "5-001a",.supply = "DBVDD",- }, {
.dev_name = "5-001a",.supply = "AVDD2",- }, {
.dev_name = "5-001a",.supply = "CPVDD",- },
+};
+static struct regulator_consumer_supply wm8994_fixed_voltage1_supplies[] = {
All these fixed voltage regulators seem a bit suspicous for a mobile phone - I'd have expected that the supplies would all be being provided by your PMIC except for things taken directly from the battery supply (like the speakers tend to be, for example)? There's no problem with the code itself, it just looks a bit odd.
All these consumer supply of WM8994 codec connected the below regulator(VCC_1.8V) on a circuit diagram. "VCC_1.8V" regualtor is always enabled, because it is used to many devices. Then I haven't connected all these consumer supply of WM8994 codec to "VCC_1.8V" regulator. I will modify that the consumer supply would be provided by PMIC.
static struct regulator_init_data aquila_buck3_data = { .constraints = { .name = "VCC_1.8V", .min_uV = 1800000, .max_uV = 1800000, .apply_uV = 1, .state_mem = { .enabled = 1, }, }, };
+static struct i2c_board_info i2c_gpio5_devs[] __initdata = {
- {
/* CS/ADDR = low 0x34 (FYI: high = 0x36) */I2C_BOARD_INFO("wm8994", 0x34 >> 1),.platform_data = &wm8994_platform_data,- },
+};
Probably clearer for generic Linux use to specify the address as 0x1a directly.
Ok, I will do.
+static void __init aquila_sound_init(void) +{
- unsigned int gpio;
- /* CODEC_XTAL_EN */
- gpio = S5PV210_GPH3(2); /* XEINT_26 */
- gpio_request(gpio, "CODEC_XTAL_EN");
- s3c_gpio_cfgpin(gpio, S3C_GPIO_OUTPUT);
- s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
- gpio_direction_output(gpio, 1);
Might be as well to provide some or all this stuff in your audio machine driver?
The Aquila board have a oscillator which provide main clock to WM8994 audio codec. The oscillator provide 24MHz clock to WM8994 audio codec (MCLK1 pin). I set gpio setting of "CODEC_XTAL_EN" to enable a oscillator.
- /* MICBIAS_EN */
- gpio = S5PV210_GPJ4(2); /* XMSMRN */
- gpio_request(gpio, "MICBIAS_EN");
- s3c_gpio_cfgpin(gpio, S3C_GPIO_OUTPUT);
- gpio_direction_output(gpio, 1);
This in particular would benefit from keeping the request of the GPIO joined up with the driver that uses it.
Ok, I will move this code to machine driver(sound/soc/s3c24xxx/aquila_wm8994.c).
- /* ADC_EN */
- gpio = S5PV210_GPJ3(2);
- gpio_request(gpio, "ADC_EN");
- s3c_gpio_cfgpin(gpio, S3C_GPIO_OUTPUT);
- gpio_direction_output(gpio, 1);
I'm not sure what this does?
I explained below description about "ADC_EN" : "ADC_EN : This gpio enable the ADC device which is used to detect the kind of jack. (SND_JACK_HEADPHONE/HEADSET/MECHANICAL/AVOUT) According to the kind of jack, an electric current is changed. (Only used on Aquila board) "
When inserting the jack to Aquila board, I used ADC driver so that, detecting the kind of jack(SND_JACK_HEADPHONE/HEADSET/MECHANICAL/AVOUT).
I will separately make the another function to initialize ADC driver.
Thank you for your comment. Chanwoo Choi