Hi
On Mon, Apr 01, 2019 at 11:39:10AM +0000, S.j. Wang wrote:
In ESAI synchronous mode, the clock is generated by Tx, So we should always set registers of Tx which relate with the bit clock and frame clock generation (TCCR, TCR, ECR), even there is only Rx is
working.
Signed-off-by: Shengjiu Wang shengjiu.wang@nxp.com
sound/soc/fsl/fsl_esai.c | 28 +++++++++++++++++++++++++++- 1 file changed, 27 insertions(+), 1 deletion(-)
diff --git a/sound/soc/fsl/fsl_esai.c b/sound/soc/fsl/fsl_esai.c index 3623aa9a6f2e..d9fcddd55c02 100644 --- a/sound/soc/fsl/fsl_esai.c +++ b/sound/soc/fsl/fsl_esai.c @@ -230,6 +230,21 @@ static int fsl_esai_set_dai_sysclk(struct
snd_soc_dai *dai, int clk_id,
return -EINVAL;}
- if (esai_priv->synchronous && !tx) {
switch (clk_id) {case ESAI_HCKR_FSYS:fsl_esai_set_dai_sysclk(dai, ESAI_HCKT_FSYS,freq, dir);break;case ESAI_HCKR_EXTAL:fsl_esai_set_dai_sysclk(dai, ESAI_HCKT_EXTAL,freq, dir);Not sure why you call set_dai_sysclk inside set_dai_sysclk again. It feels very confusing to do so, especially without a comments.
For sync mode, only RX is enabled, the register of tx should be set, so call the Set_dai_sysclk again.
Yea, I understood that. But why not just replace RX with TX on the register- writing level? Do we need to set both TCCR and RCCR? Your change in hw_params() only sets TCCR inside fsl_esai_set_bclk(), so we probably only need to change TCCR for recordings running in sync mode, right?
From the commit message, it feels like that only the clock-related fields in the TX registers need to be set. Things like calculation and setting the direction of HCKx pin don't need to run again.
@@ -537,10 +552,21 @@ static int fsl_esai_hw_params(struct snd_pcm_substream *substream,
bclk = params_rate(params) * slot_width * esai_priv->slots;
- ret = fsl_esai_set_bclk(dai, tx, bclk);
- ret = fsl_esai_set_bclk(dai, esai_priv->synchronous ? true : tx,
+bclk); if (ret) return ret;
- if (esai_priv->synchronous && !tx) {
/* Use Normal mode to support monaural audio */regmap_update_bits(esai_priv->regmap, REG_ESAI_TCR,ESAI_xCR_xMOD_MASK,params_channels(params) > 1 ?
ESAI_xCR_xMOD_NETWORK : 0);mask = ESAI_xCR_xSWS_MASK | ESAI_xCR_PADC;val = ESAI_xCR_xSWS(slot_width, width) | ESAI_xCR_PADC;regmap_update_bits(esai_priv->regmap, REG_ESAI_TCR,mask, val);
- }
Does synchronous mode require to set both TCR and RCR? or just TCR?
Both TCR and RCR. RCR will be set in normal flow.
OK. Settings both xCRs makes sense. Would you please try this:
=============== @@ -537,14 +552,20 @@ static int fsl_esai_hw_params(struct snd_pcm_substream *substream,
bclk = params_rate(params) * slot_width * esai_priv->slots;
ret = fsl_esai_set_bclk(dai, tx, bclk);
/* Synchronous mode uses TX clock generator */ret = fsl_esai_set_bclk(dai, esai_priv->synchronous || tx,bclk); if (ret) return ret;
mask = ESAI_xCR_xMOD_MASK | ESAI_xCR_xSWS_MASK;val = ESAI_xCR_xSWS(slot_width, width); /* Use Normal mode to support monaural audio */
regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx),ESAI_xCR_xMOD_MASK, params_channels(params) > 1 ?ESAI_xCR_xMOD_NETWORK : 0);
val |= params_channels(params) > 1 ? ESAI_xCR_xMOD_NETWORK : 0;regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx), mask, val);/* Recording in synchronous mode needs to set TCR also */if (!tx && esai_priv->synchronous)regmap_update_bits(esai_priv->regmap, REG_ESAI_TCR,mask, val);
regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), ESAI_xFCR_xFR_MASK, ESAI_xFCR_xFR); @@ -556,10+577,10 @@ static int fsl_esai_hw_params(struct snd_pcm_substream *substream,
regmap_update_bits(esai_priv->regmap, REG_ESAI_xFCR(tx), mask, val);
mask = ESAI_xCR_xSWS_MASK | (tx ? ESAI_xCR_PADC : 0);val = ESAI_xCR_xSWS(slot_width, width) | (tx ? ESAI_xCR_PADC : 0);regmap_update_bits(esai_priv->regmap, REG_ESAI_xCR(tx), mask, val);
/* Only TCR has padding bit and needs to be set for synchronousmode */
if (tx || esai_priv->synchronous)regmap_update_bits(esai_priv->regmap, REG_ESAI_TCR,ESAI_xCR_PADC, ESAI_xCR_PADC); /* Remove ESAI personal reset by configuring ESAI_PCRC andESAI_PRRC */ regmap_update_bits(esai_priv->regmap, REG_ESAI_PRRC, ===============
It merges those plain settings so we won't need to change both sides if there's a modification of xCR settings in the future.
Thanks for reviewing, will send v2. And the ESAI_xCR_PADC, ESAI_xCR_xMOD_NETWORK Is not needed in sync mode.