Enable support for HDMI LPE audio mode on Baytrail and Cherrytrail when HDaudio controller is not detected
Setup minimum required resources during i915_driver_load: 1. Create a platform device to share MMIO/IRQ resources 2. Make the platform device child of i915 device for runtime PM. 3. Create IRQ chip to forward HDMI LPE audio irqs.
HDMI LPE audio driver (a standalone sound driver) probes the LPE audio device and creates a new sound card.
Signed-off-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com Signed-off-by: Jerome Anand jerome.anand@intel.com --- Documentation/gpu/i915.rst | 9 + drivers/gpu/drm/i915/Makefile | 3 + drivers/gpu/drm/i915/i915_drv.c | 8 +- drivers/gpu/drm/i915/i915_drv.h | 15 ++ drivers/gpu/drm/i915/i915_irq.c | 27 +++ drivers/gpu/drm/i915/i915_reg.h | 3 + drivers/gpu/drm/i915/intel_lpe_audio.c | 363 +++++++++++++++++++++++++++++++++ include/drm/intel_lpe_audio.h | 45 ++++ 8 files changed, 471 insertions(+), 2 deletions(-) create mode 100644 drivers/gpu/drm/i915/intel_lpe_audio.c create mode 100644 include/drm/intel_lpe_audio.h
diff --git a/Documentation/gpu/i915.rst b/Documentation/gpu/i915.rst index 117d2ab..a671eee 100644 --- a/Documentation/gpu/i915.rst +++ b/Documentation/gpu/i915.rst @@ -213,6 +213,15 @@ Video BIOS Table (VBT) .. kernel-doc:: drivers/gpu/drm/i915/intel_vbt_defs.h :internal:
+intel hdmi lpe audio support +---------------------------- + +.. kernel-doc:: drivers/gpu/drm/i915/intel_lpe_audio.c + :doc: LPE Audio integration for HDMI or DP playback + +.. kernel-doc:: drivers/gpu/drm/i915/intel_lpe_audio.c + :internal: + Memory Management and Command Submission ========================================
diff --git a/drivers/gpu/drm/i915/Makefile b/drivers/gpu/drm/i915/Makefile index 580602d..3a2369c 100644 --- a/drivers/gpu/drm/i915/Makefile +++ b/drivers/gpu/drm/i915/Makefile @@ -126,6 +126,9 @@ i915-y += intel_gvt.o include $(src)/gvt/Makefile endif
+# LPE Audio for VLV and CHT +i915-y += intel_lpe_audio.o + obj-$(CONFIG_DRM_I915) += i915.o
CFLAGS_i915_trace_points.o := -I$(src) diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c index b893e67..93811ed 100644 --- a/drivers/gpu/drm/i915/i915_drv.c +++ b/drivers/gpu/drm/i915/i915_drv.c @@ -1144,7 +1144,8 @@ static void i915_driver_register(struct drm_i915_private *dev_priv) if (IS_GEN5(dev_priv)) intel_gpu_ips_init(dev_priv);
- i915_audio_component_init(dev_priv); + if (intel_lpe_audio_init(dev_priv) < 0) + i915_audio_component_init(dev_priv);
/* * Some ports require correctly set-up hpd registers for detection to @@ -1162,7 +1163,10 @@ static void i915_driver_register(struct drm_i915_private *dev_priv) */ static void i915_driver_unregister(struct drm_i915_private *dev_priv) { - i915_audio_component_cleanup(dev_priv); + if (HAS_LPE_AUDIO(dev_priv)) + intel_lpe_audio_teardown(dev_priv); + else + i915_audio_component_cleanup(dev_priv);
intel_gpu_ips_teardown(); acpi_video_unregister(); diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h index 970e50b..2a79048 100644 --- a/drivers/gpu/drm/i915/i915_drv.h +++ b/drivers/gpu/drm/i915/i915_drv.h @@ -2284,6 +2284,12 @@ struct drm_i915_private { /* Used to save the pipe-to-encoder mapping for audio */ struct intel_encoder *av_enc_map[I915_MAX_PIPES];
+ /* necessary resource sharing with HDMI LPE audio driver. */ + struct { + struct platform_device *platdev; + int irq; + } lpe_audio; + /* * NOTE: This is the dri1/ums dungeon, don't add stuff here. Your patch * will be rejected. Instead look for a better place. @@ -2773,6 +2779,8 @@ intel_info(const struct drm_i915_private *dev_priv)
#define HAS_POOLED_EU(dev_priv) ((dev_priv)->info.has_pooled_eu)
+#define HAS_LPE_AUDIO(dev_priv) ((dev_priv)->lpe_audio.platdev != NULL) + #define INTEL_PCH_DEVICE_ID_MASK 0xff00 #define INTEL_PCH_IBX_DEVICE_ID_TYPE 0x3b00 #define INTEL_PCH_CPT_DEVICE_ID_TYPE 0x1c00 @@ -3547,6 +3555,13 @@ extern int i915_restore_state(struct drm_device *dev); void i915_setup_sysfs(struct drm_i915_private *dev_priv); void i915_teardown_sysfs(struct drm_i915_private *dev_priv);
+/* i915_lpe_audio.c */ +int intel_lpe_audio_init(struct drm_i915_private *dev_priv); +int intel_lpe_audio_setup(struct drm_i915_private *dev_priv); +void intel_lpe_audio_teardown(struct drm_i915_private *dev_priv); +void intel_lpe_audio_irq_handler(struct drm_i915_private *dev_priv); +bool intel_lpe_audio_detect(struct drm_i915_private *dev_priv); + /* intel_i2c.c */ extern int intel_setup_gmbus(struct drm_device *dev); extern void intel_teardown_gmbus(struct drm_device *dev); diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c index 07ca71c..6f710da 100644 --- a/drivers/gpu/drm/i915/i915_irq.c +++ b/drivers/gpu/drm/i915/i915_irq.c @@ -1894,6 +1894,14 @@ static irqreturn_t valleyview_irq_handler(int irq, void *arg) valleyview_pipestat_irq_ack(dev_priv, iir, pipe_stats);
/* + * LPE audio interrupts are only enabled on Baytrail and + * CherryView platforms without HDaudio + */ + if (iir & (I915_LPE_PIPE_A_INTERRUPT | + I915_LPE_PIPE_B_INTERRUPT)) + intel_lpe_audio_irq_handler(dev_priv); + + /* * VLV_IIR is single buffered, and reflects the level * from PIPESTAT/PORT_HOTPLUG_STAT, hence clear it last. */ @@ -1974,6 +1982,15 @@ static irqreturn_t cherryview_irq_handler(int irq, void *arg) valleyview_pipestat_irq_ack(dev_priv, iir, pipe_stats);
/* + * LPE audio interrupts are only enabled on Baytrail and + * CherryView platforms without HDaudio + */ + if (iir & (I915_LPE_PIPE_A_INTERRUPT | + I915_LPE_PIPE_B_INTERRUPT | + I915_LPE_PIPE_C_INTERRUPT)) + intel_lpe_audio_irq_handler(dev_priv); + + /* * VLV_IIR is single buffered, and reflects the level * from PIPESTAT/PORT_HOTPLUG_STAT, hence clear it last. */ @@ -2914,6 +2931,7 @@ static void vlv_display_irq_postinstall(struct drm_i915_private *dev_priv) u32 pipestat_mask; u32 enable_mask; enum pipe pipe; + u32 val;
pipestat_mask = PLANE_FLIP_DONE_INT_STATUS_VLV | PIPE_CRC_DONE_INTERRUPT_STATUS; @@ -2930,6 +2948,15 @@ static void vlv_display_irq_postinstall(struct drm_i915_private *dev_priv)
WARN_ON(dev_priv->irq_mask != ~0);
+ /* add interrupt masks unconditially here, the actual unmask + * will take place only if the LPE_AUDIO mode is detected + */ + val = (I915_LPE_PIPE_A_INTERRUPT | + I915_LPE_PIPE_B_INTERRUPT | + I915_LPE_PIPE_C_INTERRUPT); + + enable_mask |= val; + dev_priv->irq_mask = ~enable_mask;
GEN5_IRQ_INIT(VLV_, dev_priv->irq_mask, enable_mask); diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h index fcad8fa..6b16ed0 100644 --- a/drivers/gpu/drm/i915/i915_reg.h +++ b/drivers/gpu/drm/i915/i915_reg.h @@ -2395,6 +2395,9 @@ enum skl_disp_power_wells { #define I915_ASLE_INTERRUPT (1<<0) #define I915_BSD_USER_INTERRUPT (1<<25)
+#define I915_HDMI_LPE_AUDIO_BASE (VLV_DISPLAY_BASE + 0x65000) +#define I915_HDMI_LPE_AUDIO_SIZE 0x1000 + #define GEN6_BSD_RNCID _MMIO(0x12198)
#define GEN7_FF_THREAD_MODE _MMIO(0x20a0) diff --git a/drivers/gpu/drm/i915/intel_lpe_audio.c b/drivers/gpu/drm/i915/intel_lpe_audio.c new file mode 100644 index 0000000..e12e5f7 --- /dev/null +++ b/drivers/gpu/drm/i915/intel_lpe_audio.c @@ -0,0 +1,363 @@ +/* + * Copyright © 2016 Intel Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice (including the next + * paragraph) shall be included in all copies or substantial portions of the + * Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS + * IN THE SOFTWARE. + * + * Authors: + * Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com + * Jerome Anand jerome.anand@intel.com + * based on VED patches + * + */ + +/** + * DOC: LPE Audio integration for HDMI or DP playback + * + * Motivation: + * Atom platforms (e.g. valleyview and cherryTrail) integrates a DMA-based + * interface as an alternative to the traditional HDaudio path. While this + * mode is unrelated to the LPE aka SST audio engine, the documentation refers + * to this mode as LPE so we keep this notation for the sake of consistency. + * + * The interface is handled by a separate standalone driver maintained in the + * ALSA subsystem for simplicity. To minimize the interaction between the two + * subsystems, a bridge is setup between the hdmi-lpe-audio and i915: + * 1. Create a platform device to share MMIO/IRQ resources + * 2. Make the platform device child of i915 device for runtime PM. + * 3. Create IRQ chip to forward the LPE audio irqs. + * the hdmi-lpe-audio driver probes the lpe audio device and creates a new + * sound card + * + * Threats: + * Due to the restriction in Linux platform device model, user need manually + * uninstall the hdmi-lpe-audio driver before uninstalling i915 module, + * otherwise we might run into use-after-free issues after i915 removes the + * platform device: even though hdmi-lpe-audio driver is released, the modules + * is still in "installed" status. + * + * Implementation: + * The MMIO/REG platform resources are created according to the registers + * specification. + * When forwarding LPE audio irqs, the flow control handler selection depends + * on the platform, for example on valleyview handle_simple_irq is enough. + * + */ + +#include <linux/acpi.h> +#include <linux/device.h> +#include <linux/pci.h> + +#include "i915_drv.h" +#include <linux/delay.h> +#include <drm/intel_lpe_audio.h> + +static struct platform_device* +lpe_audio_platdev_create(struct drm_i915_private *dev_priv) +{ + struct drm_device *dev = &dev_priv->drm; + int ret; + struct resource rsc[2] = {}; + struct platform_device *platdev; + u64 *dma_mask; + struct intel_hdmi_lpe_audio_pdata *pdata; + + if (dev_priv->lpe_audio.irq < 0) + return ERR_PTR(-EINVAL); + + platdev = platform_device_alloc("hdmi-lpe-audio", -1); + if (!platdev) { + ret = -ENOMEM; + DRM_ERROR("Failed to allocate LPE audio platform device\n"); + goto err; + } + + /* to work-around check_addr in nommu_map_sg() */ + dma_mask = kmalloc(sizeof(*platdev->dev.dma_mask), GFP_KERNEL); + if (!dma_mask) { + ret = -ENOMEM; + DRM_ERROR("Failed to allocate dma_mask\n"); + goto err_put_dev; + } + *dma_mask = DMA_BIT_MASK(32); + platdev->dev.dma_mask = dma_mask; + platdev->dev.coherent_dma_mask = *dma_mask; + + rsc[0].start = rsc[0].end = dev_priv->lpe_audio.irq; + rsc[0].flags = IORESOURCE_IRQ; + rsc[0].name = "hdmi-lpe-audio-irq"; + + rsc[1].start = pci_resource_start(dev->pdev, 0) + + I915_HDMI_LPE_AUDIO_BASE; + rsc[1].end = pci_resource_start(dev->pdev, 0) + + I915_HDMI_LPE_AUDIO_BASE + I915_HDMI_LPE_AUDIO_SIZE - 1; + rsc[1].flags = IORESOURCE_MEM; + rsc[1].name = "hdmi-lpe-audio-mmio"; + + ret = platform_device_add_resources(platdev, rsc, 2); + if (ret) { + DRM_ERROR("Failed to add resource for platform device: %d\n", + ret); + goto err_put_dev; + } + + pdata = kzalloc(sizeof(*pdata), GFP_KERNEL); + + if (pdata == NULL) { + ret = -ENOMEM; + goto err_put_dev; + } + platdev->dev.platform_data = pdata; + spin_lock_init(&pdata->lpe_audio_slock); + + /* for LPE audio driver's runtime-PM */ + platdev->dev.parent = dev->dev; + ret = platform_device_add(platdev); + if (ret) { + DRM_ERROR("Failed to add LPE audio platform device: %d\n", + ret); + goto err_put_dev; + } + + return platdev; +err_put_dev: + platform_device_put(platdev); + kfree(dma_mask); +err: + return ERR_PTR(ret); +} + +static void lpe_audio_platdev_destroy(struct drm_i915_private *dev_priv) +{ + platform_device_unregister(dev_priv->lpe_audio.platdev); + kfree(dev_priv->lpe_audio.platdev->dev.dma_mask); +} + +static void lpe_audio_irq_unmask(struct irq_data *d) +{ + struct drm_i915_private *dev_priv = d->chip_data; + unsigned long irqflags; + u32 val = (I915_LPE_PIPE_A_INTERRUPT | + I915_LPE_PIPE_B_INTERRUPT); + + spin_lock_irqsave(&dev_priv->irq_lock, irqflags); + + /* + * VLV_IER is already set in the vlv_display_postinstall(), + * we only change VLV_IIR and VLV_IMR + */ + dev_priv->irq_mask &= ~val; + I915_WRITE(VLV_IIR, val); + I915_WRITE(VLV_IIR, val); + I915_WRITE(VLV_IMR, dev_priv->irq_mask); + POSTING_READ(VLV_IMR); + + spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags); +} + +static void lpe_audio_irq_mask(struct irq_data *d) +{ + struct drm_i915_private *dev_priv = d->chip_data; + unsigned long irqflags; + u32 val = (I915_LPE_PIPE_A_INTERRUPT | + I915_LPE_PIPE_B_INTERRUPT); + + spin_lock_irqsave(&dev_priv->irq_lock, irqflags); + + /* + * VLV_IER is already set in the vlv_display_postinstall(), + * we only change VLV_IIR and VLV_IMR + */ + dev_priv->irq_mask |= val; + I915_WRITE(VLV_IMR, dev_priv->irq_mask); + I915_WRITE(VLV_IIR, val); + I915_WRITE(VLV_IIR, val); + POSTING_READ(VLV_IIR); + + spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags); +} + +static struct irq_chip lpe_audio_irqchip = { + .name = "hdmi_lpe_audio_irqchip", + .irq_mask = lpe_audio_irq_mask, + .irq_unmask = lpe_audio_irq_unmask, +}; + +static int lpe_audio_irq_init(struct drm_i915_private *dev_priv) +{ + int irq = dev_priv->lpe_audio.irq; + + WARN_ON(!intel_irqs_enabled(dev_priv)); + irq_set_chip_and_handler_name(irq, + &lpe_audio_irqchip, + handle_simple_irq, + "hdmi_lpe_audio_irq_handler"); + + return irq_set_chip_data(irq, dev_priv); +} + +/** + * intel_lpe_audio_irq_handler() - forwards the LPE audio irq + * @dev_priv: the i915 drm device private data + * + * the LPE Audio irq is forwarded to the irq handler registered by LPE audio + * driver. + */ +void intel_lpe_audio_irq_handler(struct drm_i915_private *dev_priv) +{ + int ret; + + ret = generic_handle_irq(dev_priv->lpe_audio.irq); + if (ret) + DRM_ERROR_RATELIMITED("error handling LPE audio irq: %d\n", + ret); +} + +/** + * intel_lpe_audio_detect() - check & setup lpe audio if present + * @dev_priv: the i915 drm device private data + * + * Detect if lpe audio is present + * + * Return: true if lpe audio present else Return = false + */ +bool intel_lpe_audio_detect(struct drm_i915_private *dev_priv) +{ + int lpe_present = false; + + if (IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv)) { + static const struct pci_device_id atom_hdaudio_ids[] = { + /* Baytrail */ + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x0f04)}, + /* Braswell */ + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x2284)}, + {} + }; + + if (!pci_dev_present(atom_hdaudio_ids)) { + DRM_INFO("%s%s\n", "HDaudio controller not detected,", + "using LPE audio instead\n"); + lpe_present = true; + } + } + return lpe_present; +} + +/** + * intel_lpe_audio_setup() - setup the bridge between HDMI LPE Audio + * driver and i915 + * @dev_priv: the i915 drm device private data + * + * set up the minimum required resources for the bridge: irq chip, + * platform resource and platform device. i915 device is set as parent + * of the new platform device. + * + * Return: 0 if successful. non-zero if allocation/initialization fails + */ +int intel_lpe_audio_setup(struct drm_i915_private *dev_priv) +{ + int ret; + + dev_priv->lpe_audio.irq = irq_alloc_desc(0); + if (dev_priv->lpe_audio.irq < 0) { + DRM_ERROR("Failed to allocate IRQ desc: %d\n", + dev_priv->lpe_audio.irq); + ret = dev_priv->lpe_audio.irq; + goto err; + } + + DRM_DEBUG("irq = %d\n", dev_priv->lpe_audio.irq); + + ret = lpe_audio_irq_init(dev_priv); + + if (ret) { + DRM_ERROR("Failed to initialize irqchip for lpe audio: %d\n", + ret); + goto err_free_irq; + } + + dev_priv->lpe_audio.platdev = lpe_audio_platdev_create(dev_priv); + + if (IS_ERR(dev_priv->lpe_audio.platdev)) { + ret = PTR_ERR(dev_priv->lpe_audio.platdev); + DRM_ERROR("Failed to create lpe audio platform device: %d\n", + ret); + goto err_free_irq; + } + + return 0; +err_free_irq: + irq_free_desc(dev_priv->lpe_audio.irq); +err: + dev_priv->lpe_audio.irq = -1; + dev_priv->lpe_audio.platdev = NULL; + return ret; +} + + +/** + * intel_lpe_audio_init() - detect and setup the bridge between HDMI LPE Audio + * driver and i915 + * @dev_priv: the i915 drm device private data + * + * Return: 0 if successful. non-zero if detection or + * llocation/initialization fails + */ +int intel_lpe_audio_init(struct drm_i915_private *dev_priv) +{ + int ret = -ENODEV; + + if (intel_lpe_audio_detect(dev_priv)) { + ret = intel_lpe_audio_setup(dev_priv); + if (ret < 0) + DRM_ERROR("failed to setup LPE Audio bridge\n"); + } + return ret; +} + +/** + * intel_lpe_audio_teardown() - destroy the bridge between HDMI LPE + * audio driver and i915 + * @dev_priv: the i915 drm device private data + * + * release all the resources for LPE audio <-> i915 bridge. + */ +void intel_lpe_audio_teardown(struct drm_i915_private *dev_priv) +{ + unsigned long irqflags; + struct irq_desc *desc; + + if (!HAS_LPE_AUDIO(dev_priv)) + return; + + desc = irq_to_desc(dev_priv->lpe_audio.irq); + + /** + * mask LPE audio irq before destroying + */ + lpe_audio_irq_mask(&desc->irq_data); + + spin_lock_irqsave(&dev_priv->irq_lock, irqflags); + + lpe_audio_platdev_destroy(dev_priv); + + irq_free_desc(dev_priv->lpe_audio.irq); + + spin_unlock_irqrestore(&dev_priv->irq_lock, irqflags); +} diff --git a/include/drm/intel_lpe_audio.h b/include/drm/intel_lpe_audio.h new file mode 100644 index 0000000..a64c449 --- /dev/null +++ b/include/drm/intel_lpe_audio.h @@ -0,0 +1,45 @@ +/* + * Copyright © 2016 Intel Corporation + * + * Permission is hereby granted, free of charge, to any person obtaining a + * copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice (including the next + * paragraph) shall be included in all copies or substantial portions of the + * Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS + * IN THE SOFTWARE. + */ + +#ifndef _INTEL_LPE_AUDIO_H_ +#define _INTEL_LPE_AUDIO_H_ + +#include <linux/types.h> + +#define HDMI_MAX_ELD_BYTES 128 + +struct intel_hdmi_lpe_audio_eld { + int port_id; + unsigned char eld_data[HDMI_MAX_ELD_BYTES]; +}; + +struct intel_hdmi_lpe_audio_pdata { + bool notify_pending; + int tmds_clock_speed; + bool hdmi_connected; + struct intel_hdmi_lpe_audio_eld eld; + void (*notify_audio_lpe)(void *audio_ptr); + spinlock_t lpe_audio_slock; +}; + +#endif /* _I915_LPE_AUDIO_H_ */