Acked-by: Rob Herring robh@kernel.org Acked-by: Sakari Ailus sakari.ailus@iki.fi Signed-off-by: Tim Harvey tharvey@gateworks.com --- v6: - replace copyright with SPDX tag - added Rob's ack
v5: - added Sakari's ack
v4: - move include/dt-bindings/media/tda1997x.h to bindings patch - clarify port node details
v3: - fix typo
v2: - add vendor prefix and remove _ from vidout-portcfg - remove _ from labels - remove max-pixel-rate property - describe and provide example for single output port - update to new audio port bindings --- .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ include/dt-bindings/media/tda1997x.h | 74 +++++++++ 2 files changed, 253 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt create mode 100644 include/dt-bindings/media/tda1997x.h
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt new file mode 100644 index 0000000..9ab53c3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt @@ -0,0 +1,179 @@ +Device-Tree bindings for the NXP TDA1997x HDMI receiver + +The TDA19971/73 are HDMI video receivers. + +The TDA19971 Video port output pins can be used as follows: + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The TDA19973 Video port output pins can be used as follows: + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The Video port output pins are mapped via 4-bit 'pin groups' allowing +for a variety of connection possibilities including swapping pin order within +pin groups. The video_portcfg device-tree property consists of register mapping +pairs which map a chip-specific VP output register to a 4-bit pin group. If +the pin group needs to be bit-swapped you can use the *_S pin-group defines. + +Required Properties: + - compatible : + - "nxp,tda19971" for the TDA19971 + - "nxp,tda19973" for the TDA19973 + - reg : I2C slave address + - interrupts : The interrupt number + - DOVDD-supply : Digital I/O supply + - DVDD-supply : Digital Core supply + - AVDD-supply : Analog supply + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. + +Optional Properties: + - nxp,audout-format : DAI bus format: "i2s" or "spdif". + - nxp,audout-width : width of audio output data bus (1-4). + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec + mclk. + +The port node shall contain one endpoint child node for its digital +output video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Optional Endpoint Properties: + The following three properties are defined in video-interfaces.txt and + are valid for the output parallel bus endpoint: + - hsync-active: Horizontal synchronization polarity. Defaults to active high. + - vsync-active: Vertical synchronization polarity. Defaults to active high. + - data-active: Data polarity. Defaults to active high. + +Examples: + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over + * 2 pixclk cycles. + */ + nxp,vidout-portcfg = + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >, + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >, + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + diff --git a/include/dt-bindings/media/tda1997x.h b/include/dt-bindings/media/tda1997x.h new file mode 100644 index 0000000..bd9fbd7 --- /dev/null +++ b/include/dt-bindings/media/tda1997x.h @@ -0,0 +1,74 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2017 Gateworks Corporation + */ +#ifndef _DT_BINDINGS_MEDIA_TDA1997X_H +#define _DT_BINDINGS_MEDIA_TDA1997X_H + +/* TDA19973 36bit Video Port control registers */ +#define TDA1997X_VP36_35_32 0 +#define TDA1997X_VP36_31_28 1 +#define TDA1997X_VP36_27_24 2 +#define TDA1997X_VP36_23_20 3 +#define TDA1997X_VP36_19_16 4 +#define TDA1997X_VP36_15_12 5 +#define TDA1997X_VP36_11_08 6 +#define TDA1997X_VP36_07_04 7 +#define TDA1997X_VP36_03_00 8 + +/* TDA19971 24bit Video Port control registers */ +#define TDA1997X_VP24_V23_20 0 +#define TDA1997X_VP24_V19_16 1 +#define TDA1997X_VP24_V15_12 3 +#define TDA1997X_VP24_V11_08 4 +#define TDA1997X_VP24_V07_04 6 +#define TDA1997X_VP24_V03_00 7 + +/* Pin groups */ +#define TDA1997X_VP_OUT_EN 0x80 /* enable output group */ +#define TDA1997X_VP_HIZ 0x40 /* hi-Z output group when not used */ +#define TDA1997X_VP_SWP 0x10 /* pin-swap output group */ +#define TDA1997X_R_CR_CBCR_3_0 (0 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_R_CR_CBCR_7_4 (1 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_R_CR_CBCR_11_8 (2 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_B_CB_3_0 (3 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_B_CB_7_4 (4 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_B_CB_11_8 (5 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_G_Y_3_0 (6 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_G_Y_7_4 (7 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +#define TDA1997X_G_Y_11_8 (8 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ) +/* pinswapped groups */ +#define TDA1997X_R_CR_CBCR_3_0_S (TDA1997X_R_CR_CBCR_3_0 | TDA1997X_VP_SWAP) +#define TDA1997X_R_CR_CBCR_7_4_S (TDA1997X_R_CR_CBCR_7_4 | TDA1997X_VP_SWAP) +#define TDA1997X_R_CR_CBCR_11_8_S (TDA1997X_R_CR_CBCR_11_8 | TDA1997X_VP_SWAP) +#define TDA1997X_B_CB_3_0_S (TDA1997X_B_CB_3_0 | TDA1997X_VP_SWAP) +#define TDA1997X_B_CB_7_4_S (TDA1997X_B_CB_7_4 | TDA1997X_VP_SWAP) +#define TDA1997X_B_CB_11_8_S (TDA1997X_B_CB_11_8 | TDA1997X_VP_SWAP) +#define TDA1997X_G_Y_3_0_S (TDA1997X_G_Y_3_0 | TDA1997X_VP_SWAP) +#define TDA1997X_G_Y_7_4_S (TDA1997X_G_Y_7_4 | TDA1997X_VP_SWAP) +#define TDA1997X_G_Y_11_8_S (TDA1997X_G_Y_11_8 | TDA1997X_VP_SWAP) + +/* Audio bus DAI format */ +#define TDA1997X_I2S16 1 /* I2S 16bit */ +#define TDA1997X_I2S32 2 /* I2S 32bit */ +#define TDA1997X_SPDIF 3 /* SPDIF */ +#define TDA1997X_OBA 4 /* One Bit Audio */ +#define TDA1997X_DST 5 /* Direct Stream Transfer */ +#define TDA1997X_I2S16_HBR 6 /* HBR straight in I2S 16bit mode */ +#define TDA1997X_I2S16_HBR_DEMUX 7 /* HBR demux in I2S 16bit mode */ +#define TDA1997X_I2S32_HBR_DEMUX 8 /* HBR demux in I2S 32bit mode */ +#define TDA1997X_SPDIF_HBR_DEMUX 9 /* HBR demux in SPDIF mode */ + +/* Audio bus channel layout */ +#define TDA1997X_LAYOUT0 0 /* 2-channel */ +#define TDA1997X_LAYOUT1 1 /* 8-channel */ + +/* Audio bus clock */ +#define TDA1997X_ACLK_16FS 0 +#define TDA1997X_ACLK_32FS 1 +#define TDA1997X_ACLK_64FS 2 +#define TDA1997X_ACLK_128FS 3 +#define TDA1997X_ACLK_256FS 4 +#define TDA1997X_ACLK_512FS 5 + +#endif /* _DT_BINDINGS_MEDIA_TDA1997X_H */