For documentation purposes and later use.
Some pre-existing but (mostly) unused definitions were renamed for consistency.
Signed-off-by: Oswald Buddenhagen oswald.buddenhagen@gmx.de --- include/sound/emu10k1.h | 78 ++++++++++++++++++++++---------- sound/pci/emu10k1/emu10k1_main.c | 2 +- 2 files changed, 56 insertions(+), 24 deletions(-)
diff --git a/include/sound/emu10k1.h b/include/sound/emu10k1.h index 6927fac1aa5f..0d288cc618c1 100644 --- a/include/sound/emu10k1.h +++ b/include/sound/emu10k1.h @@ -61,8 +61,8 @@ /* the relevant bits and zero to the other bits */ #define IPR_P16V 0x80000000 /* Bit set when the CA0151 P16V chip wishes to interrupt */ -#define IPR_GPIOMSG 0x20000000 /* GPIO message interrupt (RE'd, still not sure - which INTE bits enable it) */ +#define IPR_WATERMARK_REACHED 0x40000000 +#define IPR_A_GPIO 0x20000000 /* GPIO input pin change */
/* The next two interrupts are for the midi port on the Audigy Drive (A_MPU1) */ #define IPR_A_MIDITRANSBUFEMPTY2 0x10000000 /* MIDI UART transmit buffer empty */ @@ -122,10 +122,14 @@ /* behavior and possibly random segfaults and */ /* lockups if enabled. */
+#define INTE_A_GPIOENABLE 0x00040000 /* Enable GPIO input change interrupts */ + /* The next two interrupts are for the midi port on the Audigy Drive (A_MPU1) */ #define INTE_A_MIDITXENABLE2 0x00020000 /* Enable MIDI transmit-buffer-empty interrupts */ #define INTE_A_MIDIRXENABLE2 0x00010000 /* Enable MIDI receive-buffer-empty interrupts */
+#define INTE_A_SPDIF_BUFFULL_ENABLE 0x00008000 +#define INTE_A_SPDIF_HALFBUFFULL_ENABLE 0x00004000
#define INTE_SAMPLERATETRACKER 0x00002000 /* Enable sample rate tracker interrupts */ /* NOTE: This bit must always be enabled */ @@ -146,9 +150,10 @@ #define WC 0x10 /* Wall Clock register */ #define WC_SAMPLECOUNTER_MASK 0x03FFFFC0 /* Sample periods elapsed since reset */ #define WC_SAMPLECOUNTER 0x14060010 -#define WC_CURRENTCHANNEL 0x0000003F /* Channel [0..63] currently being serviced */ +#define WC_CURRENTCHANNEL_MASK 0x0000003F /* Channel [0..63] currently being serviced */ /* NOTE: Each channel takes 1/64th of a sample */ /* period to be serviced. */ +#define WC_CURRENTCHANNEL 0x06000010
#define HCFG 0x14 /* Hardware config register */ /* NOTE: There is no reason to use the legacy */ @@ -276,7 +281,7 @@ /* NOTE: After the rate is changed, a maximum */ /* of 1024 sample periods should be allowed */ /* before the new rate is guaranteed accurate. */ -#define TIMER_RATE_MASK 0x000003ff /* Timer interrupt rate in sample periods */ +#define TIMER_RATE_MASK 0x03ff /* Timer interrupt rate in sample periods */ /* 0 == 1024 periods, [1..4] are not useful */
#define AC97DATA 0x1c /* AC97 register set data register (16 bit) */ @@ -425,7 +430,7 @@
#define CCCA 0x08 /* Filter Q, interp. ROM, byte size, cur. addr register */ #define CCCA_RESONANCE 0xf0000000 /* Lowpass filter resonance (Q) height */ -#define CCCA_INTERPROMMASK 0x0e000000 /* Selects passband of interpolation ROM */ +#define CCCA_INTERPROM_MASK 0x0e000000 /* Selects passband of interpolation ROM */ /* 1 == full band, 7 == lowpass */ /* ROM 0 is used when pitch shifting downward or less */ /* then 3 semitones upward. Increasingly higher ROM */ @@ -487,7 +492,7 @@ /* 0x8000-n == 666*n usec delay */
#define ATKHLDV 0x11 /* Volume envelope hold and attack register */ -#define ATKHLDV_PHASE0 0x00008000 /* 0 = Begin attack phase */ +#define ATKHLDV_PHASE0_MASK 0x00008000 /* 0 = Begin attack phase */ #define ATKHLDV_HOLDTIME_MASK 0x00007f00 /* Envelope hold time (127-n == n*88.2msec) */ #define ATKHLDV_ATTACKTIME_MASK 0x0000007f /* Envelope attack time, log encoded */ /* 0 = infinite, 1 = 10.9msec, ... 0x7f = 5.5msec */ @@ -510,7 +515,7 @@ /* 0x8000-n == 666*n usec delay */
#define ATKHLDM 0x15 /* Modulation envelope hold and attack register */ -#define ATKHLDM_PHASE0 0x00008000 /* 0 = Begin attack phase */ +#define ATKHLDM_PHASE0_MASK 0x00008000 /* 0 = Begin attack phase */ #define ATKHLDM_HOLDTIME 0x00007f00 /* Envelope hold time (127-n == n*42msec) */ #define ATKHLDM_ATTACKTIME 0x0000007f /* Envelope attack time, log encoded */ /* 0 = infinite, 1 = 11msec, ... 0x7f = 5.5msec */ @@ -839,34 +844,45 @@ #define A_FXWC1 0x74 /* Selects 0x7f-0x60 for FX recording */ #define A_FXWC2 0x75 /* Selects 0x9f-0x80 for FX recording */
-/* Extended Hardware Control */ -#define A_SPDIF_SAMPLERATE 0x76 /* Set the sample rate of SPDIF output */ -#define A_SAMPLE_RATE 0x76 /* Various sample rate settings. */ -#define A_SAMPLE_RATE_NOT_USED 0x0ffc111e /* Bits that are not used and cannot be set. */ -#define A_SAMPLE_RATE_UNKNOWN 0xf0030001 /* Bits that can be set, but have unknown use. */ +#define A_EHC 0x76 /* Extended Hardware Control */ + +#define A_SPDIF_SAMPLERATE A_EHC /* Set the sample rate of SPDIF output */ #define A_SPDIF_RATE_MASK 0x000000e0 /* Any other values for rates, just use 48000 */ -#define A_SPDIF_48000 0x00000000 +#define A_SPDIF_48000 0x00000000 /* kX calls this BYPASS */ #define A_SPDIF_192000 0x00000020 #define A_SPDIF_96000 0x00000040 #define A_SPDIF_44100 0x00000080 +#define A_SPDIF_MUTED 0x000000c0
#define A_I2S_CAPTURE_RATE_MASK 0x00000e00 /* This sets the capture PCM rate, but it is */ #define A_I2S_CAPTURE_48000 0x00000000 /* unclear if this sets the ADC rate as well. */ #define A_I2S_CAPTURE_192000 0x00000200 #define A_I2S_CAPTURE_96000 0x00000400 #define A_I2S_CAPTURE_44100 0x00000800
-#define A_PCM_RATE_MASK 0x0000e000 /* This sets the playback PCM rate on the P16V */ -#define A_PCM_48000 0x00000000 -#define A_PCM_192000 0x00002000 -#define A_PCM_96000 0x00004000 -#define A_PCM_44100 0x00008000 +#define A_EHC_SRC48_MASK 0x0000e000 /* This sets the playback PCM rate on the P16V */ +#define A_EHC_SRC48_BYPASS 0x00000000 +#define A_EHC_SRC48_192 0x00002000 +#define A_EHC_SRC48_96 0x00004000 +#define A_EHC_SRC48_44 0x00008000 +#define A_EHC_SRC48_MUTED 0x0000c000 + +#define A_EHC_P17V_TVM 0x00000001 /* Tank virtual memory mode */ +#define A_EHC_P17V_SEL0_MASK 0x00030000 /* Aka A_EHC_P16V_PB_RATE; 00: 48, 01: 44.1, 10: 96, 11: 192 */ +#define A_EHC_P17V_SEL1_MASK 0x000c0000 +#define A_EHC_P17V_SEL2_MASK 0x00300000 +#define A_EHC_P17V_SEL3_MASK 0x00c00000 + +#define A_EHC_ASYNC_BYPASS 0x80000000
#define A_SRT3 0x77 /* I2S0 Sample Rate Tracker Status */ #define A_SRT4 0x78 /* I2S1 Sample Rate Tracker Status */ #define A_SRT5 0x79 /* I2S2 Sample Rate Tracker Status */ /* - default to 0x01080000 on my audigy 2 ZS --rlrevell */
+#define A_SRT_ESTSAMPLERATE 0x001fffff +#define A_SRT_RATELOCKED 0x01000000 + #define A_TTDA 0x7a /* Tank Table DMA Address */ #define A_TTDD 0x7b /* Tank Table DMA Data */
@@ -981,7 +997,7 @@ #define EMU_HANA_WCLOCK_INT_44_1K 0x01 #define EMU_HANA_WCLOCK_HANA_SPDIF_IN 0x02 #define EMU_HANA_WCLOCK_HANA_ADAT_IN 0x03 -#define EMU_HANA_WCLOCK_SYNC_BNCN 0x04 +#define EMU_HANA_WCLOCK_SYNC_BNC 0x04 #define EMU_HANA_WCLOCK_2ND_HANA 0x05 #define EMU_HANA_WCLOCK_SRC_RESERVED 0x06 #define EMU_HANA_WCLOCK_OFF 0x07 /* For testing, forces fallback to DEFCLOCK */ @@ -1010,23 +1026,27 @@ #define EMU_HANA_IRQ_DOCK_LOST 0x08
#define EMU_HANA_SPDIF_MODE 0x0a /* 00xxxxx 5 bits SPDIF MODE */ -#define EMU_HANA_SPDIF_MODE_TX_COMSUMER 0x00 +#define EMU_HANA_SPDIF_MODE_TX_CONSUMER 0x00 #define EMU_HANA_SPDIF_MODE_TX_PRO 0x01 #define EMU_HANA_SPDIF_MODE_TX_NOCOPY 0x02 -#define EMU_HANA_SPDIF_MODE_RX_COMSUMER 0x00 +#define EMU_HANA_SPDIF_MODE_RX_CONSUMER 0x00 #define EMU_HANA_SPDIF_MODE_RX_PRO 0x04 #define EMU_HANA_SPDIF_MODE_RX_NOCOPY 0x08 #define EMU_HANA_SPDIF_MODE_RX_INVALID 0x10
#define EMU_HANA_OPTICAL_TYPE 0x0b /* 00000xx 2 bits ADAT or SPDIF in/out */ #define EMU_HANA_OPTICAL_IN_SPDIF 0x00 #define EMU_HANA_OPTICAL_IN_ADAT 0x01 #define EMU_HANA_OPTICAL_OUT_SPDIF 0x00 #define EMU_HANA_OPTICAL_OUT_ADAT 0x02
#define EMU_HANA_MIDI_IN 0x0c /* 000000x 1 bit Control MIDI */ -#define EMU_HANA_MIDI_IN_FROM_HAMOA 0x00 /* HAMOA MIDI in to Alice 2 MIDI B */ -#define EMU_HANA_MIDI_IN_FROM_DOCK 0x01 /* Audio Dock MIDI in to Alice 2 MIDI B */ +#define EMU_HANA_MIDI_INA_FROM_HAMOA 0x01 /* HAMOA MIDI in to Alice 2 MIDI A */ +#define EMU_HANA_MIDI_INA_FROM_DOCK1 0x02 /* Audio Dock-1 MIDI in to Alice 2 MIDI A */ +#define EMU_HANA_MIDI_INA_FROM_DOCK2 0x03 /* Audio Dock-2 MIDI in to Alice 2 MIDI A */ +#define EMU_HANA_MIDI_INB_FROM_HAMOA 0x08 /* HAMOA MIDI in to Alice 2 MIDI B */ +#define EMU_HANA_MIDI_INB_FROM_DOCK1 0x10 /* Audio Dock-1 MIDI in to Alice 2 MIDI B */ +#define EMU_HANA_MIDI_INB_FROM_DOCK2 0x18 /* Audio Dock-2 MIDI in to Alice 2 MIDI B */
#define EMU_HANA_DOCK_LEDS_1 0x0d /* 000xxxx 4 bit Audio Dock LEDs */ #define EMU_HANA_DOCK_LEDS_1_MIDI1 0x01 /* MIDI 1 LED on */ @@ -1119,6 +1139,10 @@
/* 0x30 - 0x3f Unused Read only registers */
+// The meaning of this is not clear; kX-project just calls it "lock" in some info-only code. +#define EMU_HANA_LOCK_STS_LO 0x38 /* 0xxxxxx lower 6 bits */ +#define EMU_HANA_LOCK_STS_HI 0x39 /* 0xxxxxx upper 6 bits */ + /************************************************************************************************/ /* EMU1010 Audio Destinations */ /************************************************************************************************/ @@ -1257,8 +1281,12 @@ #define EMU_DST_DOCK_SPDIF_RIGHT2 0x011f /* Audio Dock SPDIF Right, 2nd or 96kHz */ #define EMU_DST_HANA_SPDIF_LEFT1 0x0200 /* Hana SPDIF Left, 1st or 48kHz only */ #define EMU_DST_HANA_SPDIF_LEFT2 0x0202 /* Hana SPDIF Left, 2nd or 96kHz */ +#define EMU_DST_HANA_SPDIF_LEFT3 0x0204 /* Hana SPDIF Left, 3rd or 192kHz */ +#define EMU_DST_HANA_SPDIF_LEFT4 0x0206 /* Hana SPDIF Left, 4th or 192kHz */ #define EMU_DST_HANA_SPDIF_RIGHT1 0x0201 /* Hana SPDIF Right, 1st or 48kHz only */ #define EMU_DST_HANA_SPDIF_RIGHT2 0x0203 /* Hana SPDIF Right, 2nd or 96kHz */ +#define EMU_DST_HANA_SPDIF_RIGHT3 0x0205 /* Hana SPDIF Right, 3rd or 192kHz */ +#define EMU_DST_HANA_SPDIF_RIGHT4 0x0207 /* Hana SPDIF Right, 4th or 192kHz */ #define EMU_DST_HAMOA_DAC_LEFT1 0x0300 /* Hamoa DAC Left, 1st or 48kHz only */ #define EMU_DST_HAMOA_DAC_LEFT2 0x0302 /* Hamoa DAC Left, 2nd or 96kHz */ #define EMU_DST_HAMOA_DAC_LEFT3 0x0304 /* Hamoa DAC Left, 3rd or 192kHz */ @@ -1409,8 +1437,12 @@ #define EMU_SRC_HANA_ADAT 0x0400 /* Hana ADAT 8 channel in +0 to +7 */ #define EMU_SRC_HANA_SPDIF_LEFT1 0x0500 /* Hana SPDIF Left, 1st or 48kHz only */ #define EMU_SRC_HANA_SPDIF_LEFT2 0x0502 /* Hana SPDIF Left, 2nd or 96kHz */ +#define EMU_SRC_HANA_SPDIF_LEFT3 0x0504 /* Hana SPDIF Left, 3rd or 192kHz */ +#define EMU_SRC_HANA_SPDIF_LEFT4 0x0506 /* Hana SPDIF Left, 4th or 192kHz */ #define EMU_SRC_HANA_SPDIF_RIGHT1 0x0501 /* Hana SPDIF Right, 1st or 48kHz only */ #define EMU_SRC_HANA_SPDIF_RIGHT2 0x0503 /* Hana SPDIF Right, 2nd or 96kHz */ +#define EMU_SRC_HANA_SPDIF_RIGHT3 0x0505 /* Hana SPDIF Right, 3rd or 192kHz */ +#define EMU_SRC_HANA_SPDIF_RIGHT4 0x0507 /* Hana SPDIF Right, 4th or 192kHz */
/* Additional inputs for 1616(M)/Microdock */
diff --git a/sound/pci/emu10k1/emu10k1_main.c b/sound/pci/emu10k1/emu10k1_main.c index 39b63c4ca1df..007c445d72bf 100644 --- a/sound/pci/emu10k1/emu10k1_main.c +++ b/sound/pci/emu10k1/emu10k1_main.c @@ -1953,7 +1953,7 @@ static const unsigned char saved_regs[] = { 0xff /* end */ }; static const unsigned char saved_regs_audigy[] = { - A_ADCIDX, A_MICIDX, A_FXWC1, A_FXWC2, A_SAMPLE_RATE, + A_ADCIDX, A_MICIDX, A_FXWC1, A_FXWC2, A_EHC, A_FXRT2, A_SENDAMOUNTS, A_FXRT1, 0xff /* end */ };