The output divider should align with the output sample rate, if use ideal sample rate, there will be a lot of overload, which would cause underrun.
The maximum divider of asrc clock is 1024, but there is no judgement for this limitaion in driver, which may cause the divider setting not correct.
For non-ideal ratio mode, the clock rate should divide the sample rate with no remainder, and the quotient should be less than 1024.
Signed-off-by: Shengjiu Wang shengjiu.wang@nxp.com --- Change in v2 - remove p2p/m2m word - use use_ideal_rate
sound/soc/fsl/fsl_asrc.c | 37 +++++++++++++++++++++++++++---------- 1 file changed, 27 insertions(+), 10 deletions(-)
diff --git a/sound/soc/fsl/fsl_asrc.c b/sound/soc/fsl/fsl_asrc.c index 0bf91a6f54b9..89cf333154c7 100644 --- a/sound/soc/fsl/fsl_asrc.c +++ b/sound/soc/fsl/fsl_asrc.c @@ -259,8 +259,11 @@ static int fsl_asrc_set_ideal_ratio(struct fsl_asrc_pair *pair, * It configures those ASRC registers according to a configuration instance * of struct asrc_config which includes in/output sample rate, width, channel * and clock settings. + * + * Note: + * use_ideal_rate = true is need by some case which need higher performance. */ -static int fsl_asrc_config_pair(struct fsl_asrc_pair *pair) +static int fsl_asrc_config_pair(struct fsl_asrc_pair *pair, bool use_ideal_rate) { struct asrc_config *config = pair->config; struct fsl_asrc *asrc_priv = pair->asrc_priv; @@ -268,7 +271,8 @@ static int fsl_asrc_config_pair(struct fsl_asrc_pair *pair) enum asrc_word_width input_word_width; enum asrc_word_width output_word_width; u32 inrate, outrate, indiv, outdiv; - u32 clk_index[2], div[2]; + u32 clk_index[2], div[2], rem[2]; + u64 clk_rate; int in, out, channels; int pre_proc, post_proc; struct clk *clk; @@ -351,8 +355,10 @@ static int fsl_asrc_config_pair(struct fsl_asrc_pair *pair) /* We only have output clock for ideal ratio mode */ clk = asrc_priv->asrck_clk[clk_index[ideal ? OUT : IN]];
- div[IN] = clk_get_rate(clk) / inrate; - if (div[IN] == 0) { + clk_rate = clk_get_rate(clk); + rem[IN] = do_div(clk_rate, inrate); + div[IN] = (u32)clk_rate; + if (div[IN] == 0 || (!ideal && (div[IN] > 1024 || rem[IN] != 0))) { pair_err("failed to support input sample rate %dHz by asrck_%x\n", inrate, clk_index[ideal ? OUT : IN]); return -EINVAL; @@ -360,18 +366,29 @@ static int fsl_asrc_config_pair(struct fsl_asrc_pair *pair)
clk = asrc_priv->asrck_clk[clk_index[OUT]];
- /* Use fixed output rate for Ideal Ratio mode (INCLK_NONE) */ - if (ideal) - div[OUT] = clk_get_rate(clk) / IDEAL_RATIO_RATE; + /* + * Output rate should be align with the out samplerate. If set too + * high output rate, there will be lots of Overload. + * But some case need higher performance, then we can use + * IDEAL_RATIO_RATE specifically for such case. + */ + clk_rate = clk_get_rate(clk); + if (ideal && use_ideal_rate) + rem[OUT] = do_div(clk_rate, IDEAL_RATIO_RATE); else - div[OUT] = clk_get_rate(clk) / outrate; + rem[OUT] = do_div(clk_rate, outrate); + div[OUT] = clk_rate;
- if (div[OUT] == 0) { + if (div[OUT] == 0 || (!ideal && (div[OUT] > 1024 || rem[OUT] != 0))) { pair_err("failed to support output sample rate %dHz by asrck_%x\n", outrate, clk_index[OUT]); return -EINVAL; }
+ /* Divider range is [1, 1024] */ + div[IN] = min_t(u32, 1024, div[IN]); + div[OUT] = min_t(u32, 1024, div[OUT]); + /* Set the channel number */ channels = config->channel_num;
@@ -560,7 +577,7 @@ static int fsl_asrc_dai_hw_params(struct snd_pcm_substream *substream, config.output_sample_rate = rate; }
- ret = fsl_asrc_config_pair(pair); + ret = fsl_asrc_config_pair(pair, false); if (ret) { dev_err(dai->dev, "fail to config asrc pair\n"); return ret;