On 08-01-20, 11:54, Pierre-Louis Bossart wrote:
From: Rander Wang rander.wang@intel.com
In the Intel QA multi-pipelines test case, there are two pipelines for playback and capture on the same bus. The test fails with an error when setting port params:
[ 599.224812] rt711 sdw:0:25d:711:0: invalid dpn_prop direction 1 port_num 0 [ 599.224815] sdw_program_slave_port_params failed -22 [ 599.224819] intel-sdw sdw-master-0: Program transport params failed: -22 [ 599.224822] intel-sdw sdw-master-0: Program params failed: -22
side note, one of these above err logs should be removed :)
[ 599.224828] sdw_enable_stream: SDW0 Pin2-Playback: done
This problem is root-caused to the programming of the capture stream ports while it is not yet prepared, the calling sequence is:
(1) hw_params for playback. The playback stream provide the port information to Bus. (2) stream_prepare for playback, Transport and port parameters are computed for playback. (3) hw_params for capture. The capture stream provide the port information to Bus, but it has not been prepared so is not accounted for in the bandwidth allocation. (4) stream_enable for playback. Program transport and port parameters for all masters and slaves. Since the transport and port parameters are not computed for capture stream, sdw_program_slave_port_params will generate a error when setting port params for capture.
in step (4), we should only program the ports for the stream that have been prepared. A stream that is only in CONFIGURED state should be ignored, its ports will be programmed when it becomes PREPARED.
Tested on Comet Lake.
GitHub issue: https://github.com/thesofproject/linux/issues/1637
This is not relevant for kernel, pls remove
Signed-off-by: Rander Wang rander.wang@intel.com Signed-off-by: Pierre-Louis Bossart pierre-louis.bossart@linux.intel.com
drivers/soundwire/stream.c | 21 ++++++++++++++++----- 1 file changed, 16 insertions(+), 5 deletions(-)
diff --git a/drivers/soundwire/stream.c b/drivers/soundwire/stream.c index da10f38298c0..198372977187 100644 --- a/drivers/soundwire/stream.c +++ b/drivers/soundwire/stream.c @@ -604,12 +604,23 @@ static int sdw_notify_config(struct sdw_master_runtime *m_rt)
- @bus: SDW bus instance
*/ -static int sdw_program_params(struct sdw_bus *bus) +static int sdw_program_params(struct sdw_bus *bus, bool prepare) { struct sdw_master_runtime *m_rt; int ret = 0;
list_for_each_entry(m_rt, &bus->m_rt_list, bus_node) {
/** this loop walks through all master runtimes for a* bus, but the ports can only be configured while* explicitly preparing a stream or handling an* already-prepared stream otherwise.
we can go upto 80 chars, make sure you align the above comment block as such
*/if (!prepare &&m_rt->stream->state == SDW_STREAM_CONFIGURED)continue;- ret = sdw_program_port_params(m_rt); if (ret < 0) { dev_err(bus->dev,
@@ -1502,7 +1513,7 @@ static int _sdw_prepare_stream(struct sdw_stream_runtime *stream,
program_params: /* Program params */
ret = sdw_program_params(bus);
ret = sdw_program_params(bus, true);@@ -1602,7 +1613,7 @@ static int _sdw_enable_stream(struct sdw_stream_runtime *stream) bus = m_rt->bus;
/* Program params */
ret = sdw_program_params(bus);
ret = sdw_program_params(bus, false);@@ -1687,7 +1698,7 @@ static int _sdw_disable_stream(struct sdw_stream_runtime *stream) struct sdw_bus *bus = m_rt->bus;
/* Program params */
ret = sdw_program_params(bus);
ret = sdw_program_params(bus, false);
Can you do a converse test as well, when the streams are running and concurrently two stream are stopped, it would be good to get it confirmed...
if (ret < 0) { dev_err(bus->dev, "Program params failed: %d\n", ret); return ret;@@ -1769,7 +1780,7 @@ static int _sdw_deprepare_stream(struct sdw_stream_runtime *stream) m_rt->ch_count * m_rt->stream->params.bps;
/* Program params */
ret = sdw_program_params(bus);
ret = sdw_program_params(bus, false);-- 2.20.1