This adds an initial machine driver for the ES8328 audio codec. The driver supports headphones, an audio regulator for both the codec itself and a speaker amp, and supports reparenting and adjusting clocks to supply the audio codec with the unusual frequency it requires.
Signed-off-by: Sean Cross xobs@kosagi.com --- .../devicetree/bindings/sound/imx-audio-es8328.txt | 60 ++++ sound/soc/fsl/Kconfig | 13 + sound/soc/fsl/Makefile | 2 + sound/soc/fsl/imx-es8328.c | 359 +++++++++++++++++++++ 4 files changed, 434 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/imx-audio-es8328.txt create mode 100644 sound/soc/fsl/imx-es8328.c
diff --git a/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt b/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt new file mode 100644 index 0000000..bd614a6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-es8328.txt @@ -0,0 +1,60 @@ +Freescale i.MX audio complex with ES8328 codec + +Required properties: +- compatible : "fsl,imx-audio-es8328" +- model : The user-visible name of this sound complex +- clocks : A list of clocks required to run the codec at 22.5792 MHz +- ssi-controller : The phandle of the i.MX SSI controller +- jack-gpio : Optional GPIO for headphone jack +- codec-supply : Power regulator for audio codec chip +- audio-amp-supply : Power regulator for speaker amps +- audio-codec : The phandle of the ES8328 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names could be power + supplies, ES8328 pins, and the jacks on the board: + + Power supplies: + * audio-amp + * codec + + ES8328 pins: + * LOUT1 + * LOUT2 + * ROUT1 + * ROUT2 + + Board connectors: + * Headphone + * Speaker + +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx-audio-es8328"; + model = "imx-audio-es8328"; + clocks = <&clks 169>, <&clks 57>, <&clks 173>, + <&clks 203>, <&clks 201>; + clock-names = "cko1", "cko1_sel", "pll4_audio", + "pll4_post_div", "cko_sel"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + jack-gpio = <&gpio5 15 0>; + codec-supply = <®_audio_codec>; + audio-amp-supply = <®_audio_amp>; + audio-routing = + "Speaker", "LOUT2", + "Speaker", "ROUT2", + "Speaker", "audio-amp", + "Headphone", "ROUT1", + "Headphone", "LOUT1"; + mux-int-port = <1>; + mux-ext-port = <3>; +}; + diff --git a/sound/soc/fsl/Kconfig b/sound/soc/fsl/Kconfig index 3793362..5f1e43f 100644 --- a/sound/soc/fsl/Kconfig +++ b/sound/soc/fsl/Kconfig @@ -229,6 +229,19 @@ config SND_SOC_IMX_WM8962 Say Y if you want to add support for SoC audio on an i.MX board with a wm8962 codec.
+config SND_SOC_IMX_ES8328 + tristate "SoC Audio support for i.MX boards with the ES8328 codec" + depends on OF && (I2C || SPI) + select SND_SOC_ES8328 + select SND_SOC_IMX_PCM_DMA + select SND_SOC_IMX_AUDMUX + select SND_SOC_FSL_SSI + select SND_SOC_FSL_UTILS + select SND_SOC_IMX_PCM_FIQ + help + Say Y if you want to add support for the ES8328 audio codec connected + via SSI/I2S over either SPI or I2C. + config SND_SOC_IMX_SGTL5000 tristate "SoC Audio support for i.MX boards with sgtl5000" depends on OF && I2C diff --git a/sound/soc/fsl/Makefile b/sound/soc/fsl/Makefile index db254e3..e561766 100644 --- a/sound/soc/fsl/Makefile +++ b/sound/soc/fsl/Makefile @@ -48,6 +48,7 @@ snd-soc-eukrea-tlv320-objs := eukrea-tlv320.o snd-soc-phycore-ac97-objs := phycore-ac97.o snd-soc-mx27vis-aic32x4-objs := mx27vis-aic32x4.o snd-soc-wm1133-ev1-objs := wm1133-ev1.o +snd-soc-imx-es8328-objs := imx-es8328.o snd-soc-imx-sgtl5000-objs := imx-sgtl5000.o snd-soc-imx-wm8962-objs := imx-wm8962.o snd-soc-imx-spdif-objs := imx-spdif.o @@ -57,6 +58,7 @@ obj-$(CONFIG_SND_SOC_EUKREA_TLV320) += snd-soc-eukrea-tlv320.o obj-$(CONFIG_SND_SOC_PHYCORE_AC97) += snd-soc-phycore-ac97.o obj-$(CONFIG_SND_SOC_MX27VIS_AIC32X4) += snd-soc-mx27vis-aic32x4.o obj-$(CONFIG_SND_MXC_SOC_WM1133_EV1) += snd-soc-wm1133-ev1.o +obj-$(CONFIG_SND_SOC_IMX_ES8328) += snd-soc-imx-es8328.o obj-$(CONFIG_SND_SOC_IMX_SGTL5000) += snd-soc-imx-sgtl5000.o obj-$(CONFIG_SND_SOC_IMX_WM8962) += snd-soc-imx-wm8962.o obj-$(CONFIG_SND_SOC_IMX_SPDIF) += snd-soc-imx-spdif.o diff --git a/sound/soc/fsl/imx-es8328.c b/sound/soc/fsl/imx-es8328.c new file mode 100644 index 0000000..5345955 --- /dev/null +++ b/sound/soc/fsl/imx-es8328.c @@ -0,0 +1,359 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2012 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/i2c.h> +#include <linux/clk.h> +#include <linux/gpio.h> +#include <linux/of_gpio.h> +#include <linux/regulator/consumer.h> +#include <linux/clk-provider.h> +#include <sound/soc.h> +#include <sound/jack.h> + +#include "imx-audmux.h" + +#define DAI_NAME_SIZE 32 +#define IMX6Q_SYSCLK 0x00 + +struct imx_es8328_data { + struct device *dev; + struct snd_soc_dai_link dai; + struct snd_soc_card card; + struct regulator *codec_regulator; + char codec_dai_name[DAI_NAME_SIZE]; + char platform_name[DAI_NAME_SIZE]; + struct clk *codec_clk; + struct clk *codec_clk_src; + struct clk *codec_clk_sel; + struct clk *codec_clk_post_div; + struct clk *system_cko; + unsigned int clk_freq_src; + unsigned int clk_frequency; + int power_gpio; + int jack_gpio; +}; + +static struct snd_soc_jack_gpio headset_jack_gpios[] = { + { + .gpio = -1, + .name = "headset-gpio", + .report = SND_JACK_HEADSET, + .invert = 0, + .debounce_time = 200, + }, +}; + +static struct snd_soc_jack headset_jack; + +static int imx_es8328_dai_init(struct snd_soc_pcm_runtime *rtd) +{ + struct imx_es8328_data *data = container_of(rtd->card, + struct imx_es8328_data, card); + struct device *dev = rtd->card->dev; + int ret; + + ret = snd_soc_dai_set_sysclk(rtd->codec_dai, IMX6Q_SYSCLK, + data->clk_frequency, SND_SOC_CLOCK_IN); + if (ret) { + dev_err(dev, "could not set codec driver clock params to %d\n", + data->clk_frequency); + return ret; + } + + /* Headphone jack detection */ + if (gpio_is_valid(data->jack_gpio)) { + ret = snd_soc_jack_new(rtd->codec, "Headphone", + SND_JACK_HEADPHONE | SND_JACK_BTN_0, + &headset_jack); + if (ret) + return ret; + + headset_jack_gpios[0].gpio = data->jack_gpio; + ret = snd_soc_jack_add_gpios(&headset_jack, + ARRAY_SIZE(headset_jack_gpios), + headset_jack_gpios); + } + + return ret; +} + +static const struct snd_soc_dapm_widget imx_es8328_dapm_widgets[] = { + SND_SOC_DAPM_MIC("Mic Jack", NULL), + SND_SOC_DAPM_HP("Headphone", NULL), + SND_SOC_DAPM_SPK("Speaker", NULL), + SND_SOC_DAPM_REGULATOR_SUPPLY("audio-amp", 1, 0), +}; + +static int imx_set_frequency(struct imx_es8328_data *data, int freq) +{ + int ret; + + ret = clk_set_parent(data->system_cko, data->codec_clk); + if (ret) { + dev_err(data->dev, "unable to set clk output"); + return ret; + } + + ret = clk_set_parent(data->codec_clk_sel, data->codec_clk_post_div); + if (ret) { + dev_err(data->dev, "unable to set clk parent"); + return ret; + } + + data->clk_freq_src = clk_round_rate(data->codec_clk_src, freq * 32); + data->clk_frequency = clk_round_rate(data->codec_clk, freq); + dev_dbg(data->dev, "clock source frequency: %d\n", data->clk_freq_src); + dev_dbg(data->dev, "clock frequency: %d\n", data->clk_frequency); + + ret = clk_set_rate(data->codec_clk_src, data->clk_freq_src); + if (ret) { + dev_err(data->dev, "unable to set source clock rate\n"); + return ret; + } + + ret = clk_set_rate(data->codec_clk, data->clk_frequency); + if (ret) { + dev_err(data->dev, "unable to set codec clock rate\n"); + return ret; + } + + ret = clk_prepare_enable(data->codec_clk); + if (ret) { + dev_err(data->dev, "unable to prepare codec clk\n"); + return ret; + } + + ret = clk_prepare_enable(data->codec_clk_src); + if (ret) { + dev_err(data->dev, "unable to prepare codec clk source\n"); + return ret; + } + return ret; +} + +static int imx_es8328_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct device_node *ssi_np, *codec_np; + struct platform_device *ssi_pdev; + struct imx_es8328_data *data; + int int_port, ext_port; + int ret; + struct device *dev = &pdev->dev; + + ret = of_property_read_u32(np, "mux-int-port", &int_port); + if (ret) { + dev_err(&pdev->dev, "mux-int-port missing or invalid\n"); + return ret; + } + ret = of_property_read_u32(np, "mux-ext-port", &ext_port); + if (ret) { + dev_err(&pdev->dev, "mux-ext-port missing or invalid\n"); + return ret; + } + + /* + * The port numbering in the hardware manual starts at 1, while + * the audmux API expects it starts at 0. + */ + int_port--; + ext_port--; + ret = imx_audmux_v2_configure_port(int_port, + IMX_AUDMUX_V2_PTCR_SYN | + IMX_AUDMUX_V2_PTCR_TFSEL(ext_port) | + IMX_AUDMUX_V2_PTCR_TCSEL(ext_port) | + IMX_AUDMUX_V2_PTCR_TFSDIR | + IMX_AUDMUX_V2_PTCR_TCLKDIR, + IMX_AUDMUX_V2_PDCR_RXDSEL(ext_port)); + if (ret) { + dev_err(&pdev->dev, "audmux internal port setup failed\n"); + return ret; + } + ret = imx_audmux_v2_configure_port(ext_port, + IMX_AUDMUX_V2_PTCR_SYN, + IMX_AUDMUX_V2_PDCR_RXDSEL(int_port)); + if (ret) { + dev_err(&pdev->dev, "audmux external port setup failed\n"); + return ret; + } + + ssi_np = of_parse_phandle(pdev->dev.of_node, "ssi-controller", 0); + codec_np = of_parse_phandle(pdev->dev.of_node, "audio-codec", 0); + if (!ssi_np || !codec_np) { + dev_err(&pdev->dev, "phandle missing or invalid\n"); + ret = -EINVAL; + goto fail; + } + + ssi_pdev = of_find_device_by_node(ssi_np); + if (!ssi_pdev) { + dev_err(&pdev->dev, "failed to find SSI platform device\n"); + ret = -EINVAL; + goto fail; + } + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) { + ret = -ENOMEM; + goto fail; + } + + data->dev = dev; + + data->jack_gpio = of_get_named_gpio(pdev->dev.of_node, + "jack-gpio", 0); + + data->power_gpio = of_get_named_gpio(pdev->dev.of_node, + "power-gpio", 0); + if (gpio_is_valid(data->power_gpio)) + devm_gpio_request_one(&pdev->dev, data->power_gpio, + GPIOF_OUT_INIT_HIGH, + "audio codec power switch"); + + /* Setup clocks */ + data->codec_clk = devm_clk_get(dev, "cko1"); + if (IS_ERR(data->codec_clk)) { + dev_err(dev, + "codec clock missing or invalid\n"); + goto fail; + } + + data->codec_clk_sel = devm_clk_get(dev, "cko1_sel"); + if (IS_ERR(data->codec_clk_sel)) { + dev_err(dev, + "codec clock select missing or invalid\n"); + goto fail; + } + + data->codec_clk_src = devm_clk_get(dev, "pll4_audio"); + if (IS_ERR(data->codec_clk_src)) { + dev_err(dev, + "codec clock source missing or invalid\n"); + goto fail; + } + + data->codec_clk_post_div = devm_clk_get(dev, "pll4_post_div"); + if (IS_ERR(data->codec_clk_post_div)) { + dev_err(dev, + "codec clock post-div missing or invalid\n"); + goto fail; + } + + data->system_cko = devm_clk_get(dev, "cko_sel"); + if (IS_ERR(data->system_cko)) { + dev_err(dev, + "system clock missing or invalid\n"); + goto fail; + } + + ret = imx_set_frequency(data, 22579200); + if (ret) + goto fail; + + data->codec_regulator = devm_regulator_get(dev, "codec"); + if (IS_ERR(data->codec_regulator)) { + dev_err(dev, "No codec regulator\n"); + data->codec_regulator = NULL; + } else { + ret = regulator_enable(data->codec_regulator); + if (ret) + dev_err(dev, + "Unable to enable codec regulator: %d\n", ret); + } + + data->dai.name = "hifi"; + data->dai.stream_name = "hifi"; + data->dai.codec_dai_name = "es8328-hifi-analog"; + data->dai.codec_of_node = codec_np; + data->dai.cpu_of_node = ssi_np; + data->dai.platform_of_node = ssi_np; + data->dai.init = &imx_es8328_dai_init; + data->dai.dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | + SND_SOC_DAIFMT_CBM_CFM; + + data->card.dev = &pdev->dev; + data->card.dapm_widgets = imx_es8328_dapm_widgets; + data->card.num_dapm_widgets = ARRAY_SIZE(imx_es8328_dapm_widgets); + ret = snd_soc_of_parse_card_name(&data->card, "model"); + if (ret) + goto fail; + ret = snd_soc_of_parse_audio_routing(&data->card, "audio-routing"); + if (ret) + goto fail; + data->card.num_links = 1; + data->card.owner = THIS_MODULE; + data->card.dai_link = &data->dai; + + ret = snd_soc_register_card(&data->card); + if (ret) + goto fail; + + platform_set_drvdata(pdev, data); +fail: + if (ssi_np) + of_node_put(ssi_np); + if (codec_np) + of_node_put(codec_np); + + return ret; +} + +static int imx_es8328_remove(struct platform_device *pdev) +{ + struct imx_es8328_data *data = platform_get_drvdata(pdev); + + snd_soc_jack_free_gpios(&headset_jack, ARRAY_SIZE(headset_jack_gpios), + headset_jack_gpios); + if (data->codec_regulator) { + int ret; + + ret = regulator_disable(data->codec_regulator); + if (ret) + dev_err(&pdev->dev, + "Unable to disable codec regulator: %d\n", ret); + } + + if (data->codec_clk) + clk_disable_unprepare(data->codec_clk); + + if (data->codec_clk_src) + clk_disable_unprepare(data->codec_clk_src); + + snd_soc_unregister_card(&data->card); + + return 0; +} + +static const struct of_device_id imx_es8328_dt_ids[] = { + { .compatible = "fsl,imx-audio-es8328", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, imx_es8328_dt_ids); + +static struct platform_driver imx_es8328_driver = { + .driver = { + .name = "imx-es8328", + .owner = THIS_MODULE, + .of_match_table = imx_es8328_dt_ids, + }, + .probe = imx_es8328_probe, + .remove = imx_es8328_remove, +}; +module_platform_driver(imx_es8328_driver); + +MODULE_AUTHOR("Sean Cross xobs@kosagi.com"); +MODULE_DESCRIPTION("Kosagi i.MX6 ES8328 ASoC machine driver"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:imx-audio-es8328");