On 07/17/2012 07:29 AM, Arun Raghavan wrote:
[x-posting back to pulseaudio-discuss since it's relevant to both lists]
On Tue, 2012-07-17 at 09:38 +1200, Matthew Gregan wrote:
I'm investigating an issue in Firefox's audio code when the PulseAudio ALSA plugin is in use. I posted about this on pulseaudio-discuss last week (http://lists.freedesktop.org/archives/pulseaudio-discuss/2012-July/014091.ht...), but I hoped I might have more success here.
Firefox requests a particular latency (100ms, 4410 frames at 44.1kHz) via snd_pcm_set_params. Inside the plugin (pcm_pulse.c:pulse_hw_params), that value is used to set up buffer_attr. When the PA stream is connected in pcm_pulse.c:pulse_prepare, PA may configure the stream with larger buffer_attr values (e.g. because the minimum sink latency has increased over time due to underruns on the server, or because the sink hardware doesn't support lower latency), but this isn't reflected in pcm->buffer_attr or higher layers in ALSA (i.e. pcm->buffer_size is not updated).
100 ms of latency is a lot, even for PulseAudio - is this some special hardware?
The problem I'm faced with is that there doesn't appear to be a way to detect and handle this issue at the ALSA API level, and requesting a too low latency results in broken audio playback rather than a PCM setup failure or a larger buffer than requested being used.
In the case of the PA server's minimum latency increasing over time, this also means that a stream that was configured and running correctly may break while running if PA increases the minimum latency above what the PCM was originally configured with.
I've attached a simple testcase that uses snd_pcm_wait, snd_pcm_avail_update, and snd_pcm_writei. Run it with a latency argument specified in milliseconds on the command line. For my local machine, 55ms works and 54ms fails immediately like so:
snd_pcm_wait wakes snd_pcm_avail_update returns 4410 snd_pcm_writei writes 4410 snd_pcm_wait wakes immediately snd_pcm_avail_update returns -EPIPE
Could you clarify what versions of PulseAudio and alsa-plugins you're using? The latest improvement to this handling was done less than a year ago and might require the latest versions of these components.
(Note that when I reported this on pulseaudio-discuss, my server's minimum latency was 45ms, and now pacmd list-sinks | grep configured\ latency reports a minimum latency of 56ms)
I'd expect to see one of the following behaviours instead:
- PCM setup fails due to requesting a too small buffer.
- Buffer is silently raised during setup and snd_pcm_avail_update requests the correct number of frames.
I think the better solution would be nr 2 in this case. Nr 1 won't solve the case where the sink's latency is increased dynamically - because the stream is moved, for example.
Presumably this could be achieved by having the PA plugin report valid values from pcm_pulse.c:pulse_hw_constraint, but I'm not sure how to query the necessary values from the server. This also wouldn't address the problem where the buffer_attr changes over time, and I'm not sure what to do about that case.
The necessary values are available via pa_stream_get_buffer_attr(). Potentially we could use this in the pulse_pointer() function to update the corresponding snd_pcm_t's period/buffer sizes, but I don't know if this is kosher with regards to what alsa-lib expects plugins to be doing.
If this is not sufficient for the initial update, from what I can see, snd_pcm_set_params() first sets period/buffer sizes, queries them for later calculations, and then commits them with snd_pcm_hw_params(). If we could move the querying to after the params are committed (and in this case, the stream is connected and buffer attributes are negotiated), that would solve your problem. Again, I'm not sure what side-effects this might have, but I've attached a draft untested patch for it.
I don't know either - and it also does not seem to solve the case where the sink's latency is suddenly increased (e g, when the sink input is moved to another sink).