Some of the parameters for data ports are not applicable or not implemented in IP. So mark them as invalid/not applicable in DT so that controller is aware of this.
Add comment to these bindings to provide more clarity on the values!
Signed-off-by: Srinivas Kandagatla srinivas.kandagatla@linaro.org --- .../bindings/soundwire/qcom,sdw.txt | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+)
diff --git a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt index b104be131235..b93a2b3e029d 100644 --- a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt +++ b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt @@ -54,6 +54,8 @@ board specific bus parameters. Value type: <prop-encoded-array> Definition: should specify payload transport window offset1 of each data port. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-offset2: @@ -61,6 +63,8 @@ board specific bus parameters. Value type: <prop-encoded-array> Definition: should specify payload transport window offset2 of each data port. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-sinterval-low: @@ -69,12 +73,16 @@ board specific bus parameters. Definition: should be sample interval low of each data port. Out ports followed by In ports. Used for Sample Interval calculation. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-word-length: Usage: optional Value type: <prop-encoded-array> Definition: should be size of payload channel sample. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-block-pack-mode: @@ -84,6 +92,8 @@ board specific bus parameters. 0 to indicate Blocks are per Channel 1 to indicate Blocks are per Port. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-block-group-count: @@ -92,6 +102,8 @@ board specific bus parameters. Definition: should be in range 1 to 4 to indicate how many sample intervals are combined into a payload. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-lane-control: @@ -100,6 +112,8 @@ board specific bus parameters. Definition: should be in range 0 to 7 to identify which data lane the data port uses. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-hstart: @@ -109,6 +123,8 @@ board specific bus parameters. SoundWire Frame, i.e. left edge of the Transport sub-frame for each port. Values between 0 and 15 are valid. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,ports-hstop: @@ -118,6 +134,8 @@ board specific bus parameters. SoundWire Frame, i.e. the right edge of the Transport sub-frame for each port. Values between 0 and 15 are valid. Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
- qcom,dports-type: @@ -128,6 +146,8 @@ board specific bus parameters. 1 for simple ports 2 for full port Out ports followed by In ports. + Value of 0xFF indicates that this option is not implemented + or applicable for the respective data port. More info in MIPI Alliance SoundWire 1.0 Specifications.
Note: