10.12.2019 19:53, Sowjanya Komatineni пишет:
On 12/9/19 3:03 PM, Sowjanya Komatineni wrote:
On 12/9/19 12:46 PM, Sowjanya Komatineni wrote:
On 12/9/19 12:12 PM, Dmitry Osipenko wrote:
08.12.2019 00:36, Sowjanya Komatineni пишет:
On 12/7/19 11:59 AM, Sowjanya Komatineni wrote:
On 12/7/19 8:00 AM, Dmitry Osipenko wrote: > 07.12.2019 18:53, Dmitry Osipenko пишет: >> 07.12.2019 18:47, Dmitry Osipenko пишет: >>> 07.12.2019 17:28, Dmitry Osipenko пишет: >>>> 06.12.2019 05:48, Sowjanya Komatineni пишет: >>>>> Tegra210 and prior Tegra PMC has clk_out_1, clk_out_2, clk_out_3 >>>>> with >>>>> mux and gate for each of these clocks. >>>>> >>>>> Currently these PMC clocks are registered by Tegra clock driver >>>>> using >>>>> clk_register_mux and clk_register_gate by passing PMC base >>>>> address >>>>> and register offsets and PMC programming for these clocks >>>>> happens >>>>> through direct PMC access by the clock driver. >>>>> >>>>> With this, when PMC is in secure mode any direct PMC access >>>>> from the >>>>> non-secure world does not go through and these clocks will >>>>> not be >>>>> functional. >>>>> >>>>> This patch adds these clocks registration with PMC as a clock >>>>> provider >>>>> for these clocks. clk_ops callback implementations for these >>>>> clocks >>>>> uses tegra_pmc_readl and tegra_pmc_writel which supports PMC >>>>> programming >>>>> in secure mode and non-secure mode. >>>>> >>>>> Signed-off-by: Sowjanya Komatineni skomatineni@nvidia.com >>>>> --- >>> [snip] >>> >>>>> + >>>>> +static const struct clk_ops pmc_clk_gate_ops = { >>>>> + .is_enabled = pmc_clk_is_enabled, >>>>> + .enable = pmc_clk_enable, >>>>> + .disable = pmc_clk_disable, >>>>> +}; >>>> What's the benefit of separating GATE from the MUX? >>>> >>>> I think it could be a single clock. >>> According to TRM: >>> >>> 1. GATE and MUX are separate entities. >>> >>> 2. GATE is the parent of MUX (see PMC's CLK_OUT paths diagram >>> in TRM). >>> >>> 3. PMC doesn't gate EXTPERIPH clock but could "force-enable" it, >>> correct?
Was following existing clk-tegra-pmc as I am not sure of reason for having these clocks registered as separate mux and gate clocks.
Yes, PMC clocks can be registered as single clock and can use clk_ops for set/get parent and enable/disable.
enable/disable of PMC clocks is for force-enable to force the clock to run regardless of ACCEPT_REQ or INVERT_REQ.
>> 4. clk_m_div2/4 are internal PMC OSC dividers and thus these clocks >> should belong to PMC. > Also, it should be "osc" and not "clk_m". I followed the same parents as it were in existing clk-tegra-pmc driver.
Yeah they are wrong and they should be from osc and not clk_m.
Will fix in next version.
Reg clk_m_div2/3, they are dividers at OSC pad and not really internal to PMC block.
current clock driver creates clk_m_div clocks which should actually be osc_div2/osc_div4 clocks with osc as parent.
There are no clk_m_div2 and clk_m_div4 from clk_m
Will fix this in next version.
Could you please describe the full EXTPERIPH clock topology and how the pinmux configuration is related to it all?
What is internal to the Tegra chip and what are the external outputs?
Is it possible to bypass PMC on T30+ for the EXTPERIPH clocks?
PMC CLK1/2/3 possible sources are OSC_DIV1, OSC_DIV2, OSC_DIV4, EXTPERIPH from CAR.
OSC_DIV1/2/4 are with internal dividers at the OSC Pads
EXTPERIPH is from CAR and it has reset and enable controls along with clock source selections to choose one of the PLLA_OUT0, CLK_S, PLLP_OUT0, CLK_M, PLLE_OUT0
So, PMC CLK1/2/4 possible parents are OSC_DIV1, OSC_DIV2, OSC_DIV4, EXTERN.
CLK1/2/3 also has Pinmux to route EXTPERIPH output on to these pins.
When EXTERN output clock is selected for these PMC clocks thru CLKx_SRC_SEL, output clock is from driver by EXTPERIPH from CAR via Pinmux logic or driven as per CLKx_SRC_SEL bypassing pinmux based on CLKx_ACCEPT_REQ bit.
PMC Clock control register has bit CLKx_ACCEPT_REQ When CLKx_ACCEPT_REQ = 0, output clock driver is from by EXTPERIPH through the pinmux When CLKx_ACCEPT_REQ = 1, output clock is based on CLKx_SRC_SEL bits (OSC_DIV1/2/4 and EXTPERIPH clock bypassing the pinmux)
FORCE_EN bit in PMC CLock control register forces the clock to run regardless of this.
PMC clock gate is based on the state of CLKx_ACCEPT_REQ and FORCE_EN like explained above.
CLKx_ACCEPT_REQ is 0 default and FORCE_EN acts as gate to enable/disable EXTPERIPH clock output to PMC CLK_OUT_1/2/3.
[and to enable OSC as well]
So I believe we need to register as MUX and Gate rather than as a single clock. Please confirm.
1. The force-enabling is applied to both OSC and EXTERN sources of PMC_CLK_OUT_x by PMC at once.
2. Both of PMC's force-enabling and OSC/EXTERN selection is internal to PMC.
Should be better to define it as a single "pmc_clk_out_x". I don't see any good reasons for differentiating PMC's Gate from the MUX, it's a single hardware unit from a point of view of the rest of the system.
Peter, do you have any objections?