On 3/17/18 1:28 AM, Guneshwor Singh wrote:
On Fri, Mar 16, 2018 at 02:03:33PM -0500, Pierre-Louis Bossart wrote:
On 3/15/18 10:40 PM, Guneshwor Singh wrote:
Hi Pierre,
On Thu, Mar 15, 2018 at 07:23:05AM -0500, Pierre-Louis Bossart wrote:
+static int cnl_rt274_clock_control(struct snd_soc_dapm_widget *w,
struct snd_kcontrol *k, int event)
+{
- struct snd_soc_dapm_context *dapm = w->dapm;
- struct snd_soc_card *card = dapm->card;
- struct snd_soc_dai *codec_dai =
snd_soc_card_get_codec_dai(card, RT274_CODEC_DAI);
- int ret, ratio = 100;
- if (!codec_dai)
return -EINVAL;
- /* Codec needs clock for Jack detection and button press */
- ret = snd_soc_dai_set_sysclk(codec_dai, RT274_SCLK_S_PLL2,
CNL_FREQ_OUT, SND_SOC_CLOCK_IN);
- if (ret < 0) {
dev_err(codec_dai->dev, "set codec sysclk failed: %d\n", ret);
return ret;
- }
- if (SND_SOC_DAPM_EVENT_ON(event)) {
ret = snd_soc_dai_set_bclk_ratio(codec_dai, ratio);
if (ret) {
dev_err(codec_dai->dev,
"set bclk ratio failed: %d\n", ret);
return ret;
}
ret = snd_soc_dai_set_pll(codec_dai, 0, RT274_PLL2_S_BCLK,
CNL_BE_FIXUP_RATE * ratio,
CNL_FREQ_OUT);
if (ret) {
dev_err(codec_dai->dev,
"enable PLL2 failed: %d\n", ret);
return ret;
}
- }
- return 0;
+}
it's not clear to me why you need a clock control? You are not changing anything that really depends on DAPM events, to e.g. take the MCLK down and use a local clock, so could this be moved to hw_params?
Yes, we can do in hw_params too. When we implemented it we thought during simultaneous playback and capture, hw_params will be called twice but clock clock event will be called just once.
Yes, I remember this discussion but what's missing here is that PLL is always set to the max value, in most cases we fall back to a local clock to save power a bit. And it's probably wrong to leave a PLL on if the clock reference is turned off on the SOC side.
Ok, got you. I should do stop in else part of it something like
else snd_soc_dai_set_pll(codec_dai, 0, RT274_PLL2_S_BCLK, 0, 0);
something like that yes, but likely using an internal codec clock source for e.g. jack detection.
- /* TDM 4 slots 24 bit, set Rx & Tx bitmask to 4 active slots */
- ret = snd_soc_dai_set_tdm_slot(codec_dai, 0xf, 0xf, 4, 24);
what are the 4 slots used for?
Ah, this is a mistake. Thanks for pointing out. It should be snd_soc_dai_set_tdm_slot(codec_dai, 0x3, 0x3, 2, 24) as we do not have speakers on rt274. Will correct in v3.
then it also begs the question why you needed to have both codec0_out and codec1_out mentioned above - same issue really about hard-coding things that should be topology defined.
It should by only codec0_out (codec1_out shouldn't be there at all).
SSP0 is the BE so this need to be hard-codec. codec0_out is a topology item to me and should not be in a machine driver.